Drain Pumps

XPARTCO DC97-19289F Washer Drain Pump Assembly The XPARTCO DC97-19289F is an aftermarket replacement washer drain pump assembly compatible with a wide range of Samsung top-load washers in the WA40, WA41, WA42, WA44, WA45, WA48, WA50, WA52, and WA54 series, as well as select Kenmore models built on the Samsung platform. The drain pump removes water from the washer tub during the drain portion of each wash cycle. When the pump fails, the washer will display error codes 5C, SE, nd, 5E, FO2, or E5, leave standing water in the tub, stop mid-cycle, or produce unusual noise during draining. This complete drain pump assembly is rated 120V, 60Hz, 80W, 1.1A with a 30-minute on / 30-minute off duty cycle. It directly replaces DC97-19289A, DC97-19289B, DC97-17349B, DC97-17366A, DC97-17366J, and PX3516-01. Note: the wire plug on the new pump may differ slightly from the original — if the connector does not match your washer's harness, transfer the wiring harness from the old pump to the new one. Installs in 20–30 minutes with basic hand tools. Quick Answer The XPARTCO DC97-19289F Washer Drain Pump Assembly fixes Samsung top-load washers displaying error codes 5C, SE, nd, 5E, FO2, or E5, not draining, leaving standing water, or making loud noise during the drain cycle. 120V/60Hz/80W/1.1A, 30 min on/30 min off duty cycle. Compatible with Samsung WA40 through WA54 series and Kenmore (Samsung-built). Replaces DC97-19289A, DC97-19289B, DC97-17349B, DC97-17366A, DC97-17366J, PX3516-01. Note: if wire plug differs, transfer harness from old pump. Common Problems This Part Fixes Error codes 5C, SE, nd, 5E, FO2, or E5 — washer cannot drain within the allotted time Washer not draining — standing water remaining in the tub after a cycle Washer stopping mid-cycle due to a drain fault Loud humming, grinding, or rattling noise during the drain cycle Water draining very slowly — worn pump motor below rated performance Water leaking from the drain pump area at the bottom of the washer Pump running continuously but water not being expelled from the tub Replaces Part Numbers This drain pump directly replaces the following OEM and cross-reference part numbers: DC97-19289F, DC97-17349B, DC97-19289B,DC97-17366A, DC97-17366J, DC97-19289A,ASM772133, AP6806651, EAP12592631, PD00049911, PX3516-01, PS12592631. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This drain pump is compatible with select top-load washers from the following brands and series: Samsung top-load washers — WA40 series (WA400PJHDWR and related models) Samsung top-load washers — WA41 series (WA41A3000AW and related models) Samsung top-load washers — WA42 series Samsung top-load washers — WA44 series (WA44A3205AW and related models) Samsung top-load washers — WA45 series (WA45H7000AW, WA45M7050AW, WA45N3050AW, WA45T3200AW and related models) Samsung top-load washers — WA48 series (WA48H7400AW and related models) Samsung top-load washers — WA50 series (WA50F9A7DSP, WA50M7450AW and related models) Samsung top-load washers — WA52 series (WA52M7750AW, WA52M8650AW and related models) Samsung top-load washers — WA54 series (WA54M8750AV and related models) Samsung top-load washers — WA456DRHDSU series Kenmore / Sears top-load washers (select Samsung-built models) Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Removes water from the tub during the drain and spin cycles for proper washer operation Resolves Samsung error codes 5C, SE, nd, 5E, FO2, and E5 caused by drain pump failure Rated 120V, 60Hz, 80W, 1.1A — correct electrical specifications for compatible Samsung top-load models 30-minute on / 30-minute off duty cycle — matches the operational requirements of compatible models Replaces DC97-19289A, DC97-19289B, DC97-17349B, DC97-17366A, DC97-17366J, and PX3516-01 Wire plug may differ from original — transfer harness from old pump if connector does not match Compatible with Samsung WA40 through WA54 series and Kenmore Samsung-built top-load washers Aftermarket replacement built to OEM-equivalent quality standards DIY repair — installs in 20–30 minutes with basic hand tools Product Specifications Part Number DC97-19289F Also Replaces DC97-19289A, DC97-19289B (prior versions) Part Type Washer Drain Pump Assembly Condition Aftermarket Replacement Application Samsung Top-Load Washers Voltage 120V AC Frequency 60 Hz Wattage 80W Amperage 1.1A Duty Cycle 30 minutes on / 30 minutes off Error Codes Resolved 5C, SE, nd, 5E, FO2, E5 Connector Note Wire plug may differ — transfer harness from old pump if needed Compatible Brands Samsung, Kenmore (Samsung-built) Installation Notes ⚠️ Unplug Washer and Shut Off Water Before Starting Disconnect power and turn off the water supply before beginning. Tilt the washer back or lay it on its side to access the drain pump at the bottom of the machine. Place towels and a shallow pan to catch residual water when the pump is disconnected. Note the wiring connector orientation before disconnecting — take a photo if needed. If the new pump's connector does not match the washer's harness, carefully transfer the wiring harness from the old pump to the new pump. Disconnect the drain hoses from the pump using pliers to loosen the clamps. Unscrew the pump mounting screws and remove the old pump. Install the new DC97-19289F pump in the same position, reconnect drain hoses and secure with clamps, and reconnect the wiring harness. Restore water supply and power, then run a drain cycle to verify proper drainage and check for leaks. Tools needed: Phillips screwdriver, pliers, shallow pan, towels. Frequently Asked Questions What error codes indicate a drain pump failure on Samsung washers? Error codes 5C, SE, nd, 5E, FO2, and E5 on Samsung top-load washers all indicate a drain fault — the washer was unable to drain within the expected time. These codes can also be caused by a clogged drain filter, blocked hose, or kinked drain line, so check those first. If the filter and hose are clear and the error persists after clearing them, the drain pump is the most likely cause. What is the difference between DC97-19289F, DC97-19289A, and DC97-19289B? These are successive revisions of the same Samsung drain pump assembly. DC97-19289A was the original version, DC97-19289B was an update, and DC97-19289F is the current version. Samsung issues revised part numbers when minor production changes are made — all three perform the same function and the DC97-19289F is the correct current replacement for any of the earlier versions. The DC97-17349B, DC97-17366A, and DC97-17366J are additional older cross-references for this pump used on earlier Samsung top-load models. Why might the wire plug on the new pump differ from the original? Samsung revised the wiring connector on this drain pump across different production runs. If the DC97-19289F pump you receive has a different connector than your washer's harness, do not force the connection. Instead, carefully remove the wiring harness from the old pump and transfer it to the new pump — both versions use the same internal terminals and the harness swap is straightforward. This is a known and documented step for this part and does not affect performance or safety. Should I check the drain filter before replacing the pump? Yes — always check and clean the drain filter and inspect the drain hose for kinks or blockages before replacing the pump. A clogged filter or blocked hose can cause the same error codes as a failed pump and clearing the blockage may resolve the problem without needing a new part. On Samsung top-load washers the drain filter is typically located at the bottom front of the machine. If the filter and hose are clear and the error persists, the pump needs replacement. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Samsung OEM part, but is manufactured to match the electrical specifications and performance of the original DC97-19289F drain pump assembly. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO 137311900 Washer Drain Pump Assembly – Compatible with Frigidaire & Electrolux Washers Product Description Restore proper water drainage and dependable washer operation with the XPARTCO 137311900 Washer Drain Pump Assembly. This high-quality aftermarket replacement pump is designed to efficiently remove water during drain and spin cycles. A worn or failing drain pump can cause standing water, slow draining, error codes, or loud humming noises. Replacing it with this reliable XPARTCO pump helps return your washer to smooth, consistent performance at a budget-friendly price. XPARTCO aftermarket parts are engineered to match original fit and function while offering a cost-effective alternative to OE or Genuine OEM components. Replaces Part Numbers 137311900, 2688889, PD00006068, EAP3655041, AP5630474, PS3655041. Compatibility This replacement washer drain pump assembly fits select Frigidaire, Electrolux, Crosley, Gibson, and Kenmore (Frigidaire-manufactured) washers. Example compatible models include (but are not limited to): Frigidaire FAFW3577KW0, FFTW4120SW Electrolux EIFLW55HIW0 Always verify your washer’s model number before ordering.Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement – Matches OEM fit and pumping performance 💧 Efficient Water Removal – Restores proper draining during cycles 🔇 Quiet, Smooth Operation – Helps eliminate humming or grinding noises 💪 Durable Motor & Housing – Built for reliable long-term use 💰 Cost-Effective Repair – Affordable alternative to OE and OEM pumps 📐 Product Specification Part Number: 137311900 Component Type: Washer Drain Pump Assembly Voltage: 120V AC Mounting: Direct-fit, bolt-on installation Application: Washer drain and spin system Quality Level: Aftermarket replacement (not OE / not OEM) 🛠️ Installation Notes Tools Needed: Phillips screwdriver, nut driver, pliers ⚠️ Safety First: Unplug the washer and shut off the water supply before servicing. Basic Steps: Disconnect washer power and water supply. Access the drain pump from the bottom or rear of the washer. Remove hoses and electrical connectors. Remove mounting screws and take out the old pump. Install the new XPARTCO 137311900 drain pump assembly. Reconnect hoses and wiring, reassemble panels, and restore power. Run a test cycle to confirm proper draining. ⏱️ Time Required: 25–35 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Aftermarket Appliance Parts 🔄 30-Day Return Policy Fix drainage issues and get your washer running smoothly again — Add to Cart Now for a dependable, budget-friendly repair!

Read more less

WPW10409079 Washer Genuine OEM Drain Pump Replaces Part Number: WPW10409079, W10409079, 2118648, AP6021043, PS11754363, LP09079. Description: This Drain Pump is a replacement part for specific Whirlpool top-loading washing machine models. Located near the bottom center of the machine, it actively pumps water out of the washer tub at the end of each cycle.  The pump motor spins an impeller chamber to push water through the drain hose and out of the home. Causes of failure include clogging from mineral buildup or fabric fibers within the pumping components. Over time, motor windings experience excess heat and may burn out from consistent drainage cycles. WPW10409079 is the part number for a Whirlpool washer drain pump that removes water from the washer during the drain cycle. It is compatible with many Whirlpool, KitchenAid, Maytag, Jenn-Air, Amana, Inglis, and Magic Chef models.

Read more less

WH23X10040 Washer Drain Pump – Genuine OEM for GE Washers The Drain Pump is a Genuine OEM part for select GE washing machine models that is responsible for removing water from the washer at the end of the wash cycle. The pump forces water out through the drain hose so that clothing comes out free of excess water, making the drying process faster.  Whether your washer is not draining, displaying error codes, or stopping mid-cycle, this original replacement pump restores full functionality and performance. ✅ Key Features: Genuine OEM part – WH23X10040 Direct fit for many GE, Hotpoint, and RCA washers Quiet and energy-efficient operation Built to factory specifications for reliability and performance Includes pump motor and housing assembly 120V, 85W, 60Hz. 🔁 Replaces Part Numbers: WH23X10040, 2216538, 228C89P001, AH3501453, EA3501453, AP5306354, PS3501453. ⚠️ Fixes These Common Washer Problems: Washer not draining properly Standing water left after spin cycle Error codes related to pump failure Washer won’t complete the cycle Loud or buzzing noise from the drain pump 🧰 Compatible Models: 36361532110 GTUN275GM1WW GTUP240EM0WW GTUP240EM1WW GTUP240EM2WW GTUP240EM3WW GTUP240EM4WW GTUP240EM5WW GTUP240EM6WW GTUP240GM0WW GTUP240GM1WW GTUP240GM2WW GTUP240GM3WW GTUP240GM4WW GTUP240GM5WW GTUP240GM6WW GTUP270EM0WW GTUP270EM1WW GTUP270EM2WW GTUP270EM3WW GTUP270GM1WW GTUP270GM2WW GTUP270GM3WW GTUP270GM4WW GTUP270GM5WW GUD27GSSJ0WW 36361542 36361542211 36361542310 36361542410 36361542411 36371532110 36371542 36371542211 36371542310 36371542410 36361532412 GTUN275GM0WW GTUN275GM2WW GTUP270EM4WW GTUP270EM5WW GTUP270GM0WW GUD24ESSJ0WW GUD24GSSJ0WW 26715321 2671532110 2671532210 2671532211 2671532212 2671532311 2671532312 2671532412 2671532413 GTUN275EM0WW GTUN275EM1WW GTUN275EM2WW 2661532412 2661532210 2661532110 2661532211 2661532212 2661532311 2661532312 2661532413 2661532513 363.6153241 GUD27ESSJ1WW GUD27ESSM0WW GUV27ESSM0WW GUD27GSSM0WW GUD27GSSM1WW GUD27ESPM0DG GUD27GSPM0DG GUD27ESPM1DG GUD27GSSJ1WW GUD27GSPM1DG GUV27ESSM1WW GUD27EESN0WW GUD27GESN0WW GUD27ESSM1WW GUD27GSSM2WW GUD27ESSJ0WW 🧰 Compatible With: ✔️ GE✔️ Hotpoint✔️ RCA (by GE)(Check your washer’s model number to ensure fit — or contact us for support.) 🚚 Why Buy from Parts-O-Matic? ✅ 100% Genuine OEM part – no cheap imitations ✅ Always Fast and Free U.S. shipping ✅ Competitive pricing with professional support ✅ Trusted by technicians and DIYers nationwide 🛒 Get your washer draining like new again — order the WH23X10040 Genuine GE Drain Pump today at Parts-O-Matic.com, and enjoy fast, free delivery across the U.S.

Read more less

W11458345 Genuine OEM Washer Drain Pump - Compatible with Whirlpool, Maytag, Amana Product Description Restore your washer’s performance with the W11458345 Genuine OEM Washer Drain Pump. This Whirlpool-manufactured pump is designed as a replacement for select Whirlpool, Maytag, Amana, Inglis, and Kenmore washing machines. It efficiently drains wastewater during wash cycles and includes a large filter that can be cleaned monthly with Washing Machine Cleaner Tablets. This part addresses issues like water not draining, loud buzzing or grinding noises, or failure to enter agitation cycles, often caused by blockages, wear, or pump motor failure. Note: Includes (1) drain pump assembly. Disconnect power before installation. Verify compatibility with your washer model. Replaces part numbers: W11458345, W11316609, W10918608, W11319789, PD00062450, EAP16218041, AP6989186, PS16218041. Compatibility: Compatible with select washer models, including but not limited to: Whirlpool: WFW862CHC3, WFW6620HW1, WFW6620HW2, WFW9620HC2, 8TWFW8620HW1 Maytag: MHW5630HW1, MHW5630HW3, 7MWFW5622HW2 Amana: NFW5800HW0 Kenmore: 110.42932200 Inglis: IFW5900HW0 Verify your model number or contact our support team for assistance. Key Features: ✅ Brand and Models Compatibility: Fits select Whirlpool, Maytag, Amana, Inglis, and Kenmore washers. 🔧 Specifications: Genuine OEM Whirlpool drain pump, 120V, stainless steel construction. 💪 Reliable Performance: Efficiently drains wastewater for optimal washer operation. 🛠️ Easy Installation: Requires screwdriver, pliers, and nut driver; typically installed in 30–60 minutes. 🛡️ Effective Fixes: Resolves water not draining, buzzing/grinding noises, or agitation cycle issues. Product Specification Part Number: W11458345 Component Type: Washer drain pump assembly Material: Stainless steel and plastic (Based on web:0, web:1, web:2, web:3, web:4, web:5, web:6, web:7, web:8, web:9, web:10, web:11, web:12, web:13, web:14, web:15) Dimensions: Approximately 9.75" L x 9.5" W x 5.25" H (Based on web:0) Weight: 3.32 lbs (Based on web:0) Electrical Specs: 120V, submersible design (Based on web:0, web:2) Compliance: UL-listed, Prop 65 warning for California (Based on web:0, web:1, web:2, web:3, web:4, web:5, web:6, web:7, web:8, web:9, web:10, web:11, web:12, web:13, web:14, web:15) Installation Notes: Safety First: Disconnect the washer from the power source before installation. Shop for high-quality appliance parts with a 30-day return policy. Keep your washer running smoothly today! Add to cart now for a reliable fix!

Read more less

W11399437 Genuine OEM Washer Drain Pump Replaces Part Numbers: AP6974144, PS12731241 Description: This Drain Pump is a Genuine OEM part for select Maytag, Kenmore, Whirlpool washer models. It is responsible for circulating water through the washing machine during all cycles. The pump draws water from the tub and dispenses it through the water supply hoses to soak, scrub, and rinse clothes.  

Read more less

W10919003 Washer Genuine OEM Drain Pump Replaces Part Numbers: W10919003, 4461359, W10775446, AP6038235, PS11770076. Description: This Water Pump is a Genuine OEM replacement part for specific Maytag, Kenmore, Whirlpool washing machine models. It plays a crucial role in circulating water throughout the wash cycles and draining the used water from the tub.

Read more less

8182415 Washer Genuine OEM Drain Pump Fits Specific Whirlpool, Maytag washer Models. Replaces Part Numbers: WP8182415, 8182415, OEM24047170, AP6011792, 1065543, PS11744991. Description: This Drain Pump is a Genuine OEM part for specific Whirlpool, Maytag, Kenmore washing machine models.    California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

XPARTCO W10276397 Washer Drain Pump Replaces WPW10276397 The XPARTCO W10276397 is an aftermarket replacement washer drain pump and motor assembly compatible with a wide range of Whirlpool-family top-load washers including Whirlpool Cabrio, Maytag Centennial, Amana, Kenmore, Roper, Crosley, and Inglis. The drain pump removes water from the washer tub during the drain portion of each wash cycle. When the pump fails, the washer will not drain, will leave standing water in the tub, display error code F9E1, stop mid-cycle, or produce unusual humming or grinding noises during the drain phase. This complete drain pump and motor assembly uses a Hanyu B40-3A motor (also marked 91PS3132) and includes the integrated impeller — the impeller is not sold separately. It directly replaces WPW10276397, W10276397, WPW10276397VP, 1874334, B40-3A, LP397, AP6018417, PS11751719, and several additional cross-reference numbers. Before ordering, confirm that the drain hose and any coin trap or filter are clear — a blocked hose or clogged filter can mimic pump failure symptoms. Installs in 20–30 minutes with basic hand tools. Quick Answer The XPARTCO W10276397 Washer Drain Pump fixes Whirlpool Cabrio and Maytag Centennial top-load washers that won't drain, leave standing water, display error code F9E1, or make humming/grinding noises during the drain cycle. Complete pump and motor assembly with integrated impeller. Motor: Hanyu B40-3A / 91PS3132. Replaces WPW10276397, 1874334, B40-3A, LP397, AP6018417, PS11751719. Compatible with Whirlpool Cabrio, Maytag Centennial/MVWC/MVWX, Amana, Kenmore, Roper, Crosley, and Inglis top-load washers. Common Problems This Part Fixes Washer not draining — standing water remaining in the tub after a cycle Error code F9E1 displayed — drain pump fault or slow drain detected Washer stopping mid-cycle due to a drain fault Loud humming during the drain phase — motor running but impeller not pumping Grinding or rattling noise during drain — physical damage to impeller or pump housing Water draining very slowly — worn pump motor below rated flow Water leaking from the drain pump area Replaces Part Numbers This drain pump directly replaces the following OEM and cross-reference part numbers: WPW10276397, W10276397, 1874334, AWP50231 EAP11751719 FIX11751719, OEM24073670, PD00003595, AP6018417, PS11751719, WPW10276397VP If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This drain pump is compatible with select top-load washers from the following brands and series: Whirlpool top-load washers — Cabrio series (WTW4800, WTW4810, WTW4850, WTW4900, WTW5000, WTW5200, WTW5300, WTW5500, WTW5600, WTW5640, WTW5700 and related models) Maytag top-load washers — Centennial series (MVWC200, MVWC215, MVWC300, MVWC400, MVWC415, MVWC416, MVWC425, MVWC465 and related models) Maytag top-load washers — MVWX series (MVWX500, MVWX550, MVWX600, MVWX700 and related models) Amana top-load washers (ATW, NTW series and related models) Kenmore / Sears top-load washers — 110 series (Whirlpool-built Cabrio-platform models) Roper top-load washers (RTW series) Crosley top-load washers (CAE series) Inglis top-load washers (select models) Note: This pump is for top-load washers only. Always verify your exact model number before ordering. Check and clear the drain hose and any coin trap before replacing the pump — a blocked hose can produce the same symptoms as a failed pump. Key Features Removes water from the tub during the drain and spin cycles for proper washer operation Complete pump and motor assembly — includes integrated impeller (impeller not sold separately) Motor: Hanyu B40-3A / 91PS3132 — matched to original pump specifications Resolves error code F9E1 (drain pump fault / slow drain) on compatible Whirlpool and Maytag top-load washers Replaces WPW10276397, W10276397, 1874334, B40-3A, LP397, and AP6018417 Compatible with Whirlpool Cabrio, Maytag Centennial/MVWX, Amana, Kenmore, Roper, Crosley, and Inglis top-load washers Aftermarket replacement built to OEM-equivalent quality standards DIY repair — installs in 20–30 minutes with basic hand tools Product Specifications Part Number W10276397 OEM Part Number WPW10276397 Part Type Washer Drain Pump and Motor Assembly Condition Aftermarket Replacement Application Top-Load Washers (Cabrio, Centennial, and related platforms) Motor Hanyu B40-3A / 91PS3132 Includes Pump motor and integrated impeller assembly Error Code Resolved F9E1 (drain pump fault / slow drain) Compatible Brands Whirlpool, Maytag, Amana, Kenmore, Roper, Crosley, Inglis Installation Notes ⚠️ Unplug Washer and Shut Off Water Before Starting Disconnect power and turn off the water supply before beginning. Place towels and a shallow pan near the pump access area to catch residual water. The drain pump is located beneath the washer tub on Cabrio and Centennial models — access it by removing the front lower panel or by tilting the washer back and working from underneath. Disconnect the drain hose clamp and hose from the pump, then disconnect the wire harness connector. Unscrew the pump mounting screws and remove the old pump. Before installing the new pump, verify the drain hose and any coin trap or filter are completely clear of debris — a blocked hose or trap will cause the new pump to fail again. Install the new W10276397 pump in the same position, reconnect the hose and wire harness, and secure the mounting screws. Restore power and water and run a drain or spin cycle to confirm drainage and check for leaks. Tools needed: Phillips screwdriver, pliers, shallow pan, towels. Frequently Asked Questions What does error code F9E1 mean on Whirlpool Cabrio and Maytag Centennial washers? F9E1 indicates a drain fault — the washer was unable to drain within the expected time during the cycle. It can be caused by a clogged drain hose, a blocked coin trap or filter, a kinked drain hose, or a failed drain pump motor. Always check and clear the drain hose and filter before replacing the pump — a blockage is often the cause and clearing it resolves the error without needing a new pump. If the hose and filter are clear and the error persists, the pump motor has likely failed. What is the difference between W10276397 and WPW10276397? These are the same drain pump assembly. WPW10276397 is the updated Whirlpool OEM part number that superseded the original W10276397. The 1874334 and B40-3A are also cross-references for this same pump. This aftermarket replacement is compatible with all of these numbers. My washer hums but won't drain — is it the pump? A humming sound during the drain cycle without water being expelled usually means the pump motor is receiving power and running, but the impeller is not turning — either because it is jammed with debris or because the impeller shaft has broken. First check for and remove any foreign objects (coins, lint, small clothing items) from the pump area. If the impeller is clear and the pump still hums without draining, the motor or impeller is mechanically failed and the pump assembly needs replacement. Does this pump fit the Whirlpool Cabrio and Maytag Bravos washers? The W10276397 is compatible with Whirlpool Cabrio and Maytag Centennial top-load washers on the VM transmission platform. Maytag Bravos XL and Bravos X models may also be compatible depending on the specific model number — verify your exact model before ordering. Contact our support team if you need confirmation for a specific Bravos model. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured with a Hanyu B40-3A motor to match the specifications and performance of the original WPW10276397 drain pump assembly. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

WH11X39237 Genuine OEM GE Washer Drain Pump The WH11X39237 is a Genuine OEM GE replacement drain pump and filter assembly compatible with select GE, GE Profile, and GE 2-in-1 Washer/Dryer Combo front-load washers in the GFW510, GFW550, GFW650, GFW655, GFW850, PFW, and PFQ series. The drain pump is responsible for removing water from the washer drum during the drain and spin cycles — when it fails, the washer will not drain, will leave standing water in the drum, or will produce unusual noises during the drain cycle. This complete drain pump and filter assembly operates at 120V, 60Hz, 1.2A and includes the pump motor, impeller housing, and integrated filter. It directly replaces the discontinued WH11X29539 — WH11X39237 is the current manufacturer-approved updated part number. Also replaces AP6986715, 4962370, B25-3A04, and several additional cross-reference numbers. Installs in 30–45 minutes with basic hand tools. Quick Answer The WH11X39237 Genuine OEM GE Washer Drain Pump fixes GE front-load washers that won't drain, leave standing water in the drum, display drain error codes, or make loud humming or grinding noises during the drain cycle. Complete pump and filter assembly. 120V/60Hz/1.2A. Replaces discontinued WH11X29539. Compatible with GE GFW510, GFW550, GFW650, GFW655, GFW850, PFW, and PFQ series. Common Problems This Part Fixes Washer not draining — standing water remaining in the drum after a cycle Drain error codes displayed on GE front-load washers (e.g. E23, E24, or pump-related codes) Loud humming, grinding, or buzzing noise during the drain cycle Washer stopping mid-cycle due to a drain fault Water leaking from around the drain pump area Drain pump running continuously but water not being expelled Pump impeller jammed by debris and motor burned out Replaces Part Numbers This drain pump directly replaces the following OEM and cross-reference part numbers: WH11X39237, WH11X29539, Hanyu B25-3A04, 9019841, PD00094541, AGE1260100, AP8054992, PS18351790. WH11X39237 is the current manufacturer-approved replacement for the discontinued WH11X29539. If your appliance documentation lists WH11X29539, this is the correct updated part. Compatibility This drain pump is compatible with select front-load washers and laundry combos from the following GE product lines: GE front-load washers — GFW510 series GE front-load washers — GFW550 series GE front-load washers — GFW650 series GE front-load washers — GFW655 series GE front-load washers — GFW850 series GE Profile front-load washers — PFW870, PFW950, PFW955 series GE Profile front-load washers — PFQ83 series GE 2-in-1 Washer/Dryer Combo (select models) Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Complete drain pump and filter assembly — pump motor, impeller housing, and integrated filter all included Removes water from the drum during drain and spin cycles for proper washer operation Integrated filter traps lint, coins, and debris to prevent pump impeller damage and clogs Electrical specs: 120V, 60Hz, 1.2A — correct for compatible GE front-load models WH11X39237 is the current manufacturer-approved replacement for discontinued WH11X29539 Direct replacement — installs into existing pump housing with no modification required Genuine OEM part manufactured by GE to factory specifications — guaranteed fit and performance Compatible with GFW510, GFW550, GFW650, GFW655, GFW850, PFW, and PFQ series DIY-friendly repair — installs in 30–45 minutes with basic hand tools Product Specifications Part Number WH11X39237 Supersedes WH11X29539 (discontinued) Part Type Washer Drain Pump and Filter Assembly Condition Genuine OEM Application GE Front-Load Washers and 2-in-1 Washer/Dryer Combos Voltage 120V AC Frequency 60 Hz Amperage 1.2A Includes Pump motor, impeller housing, and integrated filter Compatible Series GFW510, GFW550, GFW650, GFW655, GFW850, PFW870, PFW950, PFW955, PFQ83 Compatible Brands GE, GE Profile Installation Notes ⚠️ Unplug Washer and Shut Off Water Before Starting Disconnect power and turn off the water supply before beginning any repair. Place towels and a shallow pan under the pump access area to catch residual water. Remove the front lower access panel of the washer. Before removing the pump, first clean the pump filter (WH23X38617) and check for a clogged filter or debris in the pump housing — a jammed impeller is sometimes mistaken for a failed pump. If the pump motor is confirmed failed, disconnect the wire harness and drain hoses from the old pump assembly, then unscrew or unclip the pump from the mounting bracket. Install the new WH11X39237 pump assembly, reconnect the drain hoses and secure with clamps, reconnect the wire harness, and reinstall the access panel. Restore power and water supply, then run a drain-only cycle to verify proper drainage and check for leaks. Tools needed: Phillips screwdriver, pliers, shallow pan or towels. Frequently Asked Questions What is the difference between WH11X39237 and WH11X29539? These are the same drain pump assembly — WH11X39237 is the current updated part number that GE issued to replace the discontinued WH11X29539. If your washer's documentation, parts diagram, or old pump label shows WH11X29539, the WH11X39237 is the correct replacement to order. Should I check the pump filter before replacing the drain pump? Yes — always check and clean the pump filter (WH23X38617) before replacing the drain pump. A heavily clogged filter can restrict water flow enough to mimic pump failure symptoms, and a foreign object jammed in the impeller can stall the pump motor without permanently damaging it. Remove the filter, clear any debris from the housing and impeller, and test the washer again. If the pump still fails to drain after cleaning, then pump replacement is the next step. How do I know if my drain pump has failed? A failed drain pump typically causes the washer to stop mid-cycle with a drain error code, or to finish a cycle with standing water in the drum. You may also hear a loud humming noise during the drain phase — this indicates the motor is running but the impeller is not turning (jammed or broken). A grinding noise suggests physical damage to the impeller or pump housing. If the pump is completely silent during the drain cycle despite power being delivered to it, the motor has likely burned out. Is the WH11X39237 compatible with GE Profile and GE 2-in-1 models? Yes — the WH11X39237 is compatible with select GE Profile front-load washers in the PFW870, PFW950, PFW955, and PFQ83 series, as well as select GE 2-in-1 Washer/Dryer Combo models. Always verify your specific model number before ordering to confirm compatibility. Is this an OEM or aftermarket part? This is a Genuine OEM part manufactured by GE to factory specifications. It is the exact same drain pump and filter assembly installed in compatible GE and GE Profile front-load washers from the factory — guaranteed fit, materials, and performance. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Genuine OEM Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less