Washer & Dryer Accessories

XPARTCO 279457 Dryer Heating Element Wire Kit The XPARTCO 279457 is an aftermarket replacement heating element connection wire kit for Whirlpool, Kenmore, Maytag, and KitchenAid electric clothes dryers. This kit includes 2 connecting wires and 2 wire connectors that join the dryer's wiring harness to the heating element terminals. Because these connections carry the full current draw of the heating circuit, they're a common failure point — the terminals and wire insulation gradually degrade from repeated heat cycling, and a loose or corroded connection creates resistance that generates even more heat, which can melt the wire insulation or the connector itself. This kit is the correct fix when you find burnt, melted, or brittle wiring at the heating element terminals rather than a fully failed heating element — replacing just the connection wiring is far cheaper than replacing the whole element when the element itself still tests good. Quick Answer The XPARTCO 279457 Heating Element Wire Kit fixes a dryer with no heat, inadequate heat, or overheating caused by burnt or melted wiring at the heating element connection — not a failed heating element itself. Includes 2 connection wires and 2 wire connectors. Classic symptom: a burning smell, or visibly melted/discolored wire insulation near the heating element terminals. Common Problems This Part Fixes Dryer not heating or producing inadequate heat Dryer overheating or heat cycling erratically Visibly melted, burnt, or discolored wires at the heating element connection Burning smell during operation Intermittent heating caused by a loose or corroded connection Heating element itself tests fine but the dryer still won't heat properly Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This wire kit directly replaces the following part numbers: 279457, 279457VP, 3140, T2502, AP3134638, AWP39894, EAP334206, PD00002893, PS334206 We were not able to confirm additional cross-reference numbers beyond these at this time. If you have one, contact our support team before ordering and we will verify compatibility. Compatibility This wire kit is compatible with a wide range of Whirlpool, Kenmore, Maytag, and KitchenAid electric clothes dryers, including models such as: TEDX640JQ1, WED5620HW1 Numerous additional Whirlpool-built electric dryer models using the 279457 connection kit Note: This kit has also been referenced for use with heating element 4391960 in some sourcing. This is a connection wire kit — it does not include a heating element itself. Confirm your model number against your dryer's parts diagram, or contact our support team to verify fit before ordering. Key Features Direct-fit aftermarket heating element connection wire kit Includes 2 connection wires and 2 wire connectors Resolves melted/burnt-wire, no-heat, and overheating symptoms caused by a bad connection Lower-cost fix than replacing the heating element when the element itself tests good Fits Whirlpool, Kenmore, Maytag, and KitchenAid electric dryers Straightforward swap — typically 15–60 minutes with basic hand tools Product Specifications Part Number XP279457 OEM Part Number 279457 Part Type Dryer Heating Element Connection Wire Kit Condition Aftermarket Replacement Kit Contents 2 Connection Wires & 2 Wire Connectors Application Whirlpool, Kenmore, Maytag & KitchenAid Electric Dryers Installation Notes ⚠️ Unplug Power Before Installing — High-Current Connection Unplug the dryer or switch off its circuit breaker before beginning — this connection carries the full current of the heating circuit and must never be serviced live. Remove the dryer's rear or front panel per your model's service guide to access the heating element. Inspect the existing connection wires and terminals for melting, discoloration, or brittleness — if you see any of these signs, replace both wires and connectors entirely rather than reusing any part of them. Disconnect the two old connection wires from the heating element terminals, install the two new wires in their place, and secure each wire connector firmly so both connections are tight with no exposed bare wire. A loose or poor connection is the most common root cause of this failure in the first place, so double-check the fit on both connections before closing the dryer back up. Frequently Asked Questions Do I need a new heating element, or just this wire kit? If the heating element itself tests good with a multimeter but you see melted, burnt, or discolored wiring specifically at the connection point, this wire kit alone is usually the correct and much cheaper fix. If the element itself has failed (no continuity), you'll need to replace the heating element too. Why did my heating element wires melt in the first place? This usually happens when a connection becomes loose or corroded over time, which increases electrical resistance at that point. That resistance generates extra heat right at the connection, which can melt the wire insulation or the connector. Make sure the new connection is seated tight and secure to prevent it from happening again. How many wires and connectors are in this kit? This kit includes 2 connection wires and 2 wire connectors — enough to replace both terminal connections on the heating element in one kit, per the original manufacturer specification. Is this safe to install myself? Most DIY-capable owners can complete this repair with basic hand tools in under an hour. That said, always unplug the dryer or shut off its breaker before working on it, since this connection carries the full current of the heating circuit — never work on it while the dryer is powered. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

W11244231 Genuine OEM Whirlpool Washer Drain Hose The W11244231 is a genuine Whirlpool OEM drain hose for Whirlpool, Maytag, Kenmore, Amana, Crosley, Admiral, Inglis, and Roper washers. This flexible tube carries used water from the washer tub to your house drain after every wash cycle, connecting the washer's outlet to your standpipe or utility sink drain connection. This hose is approximately 4 feet long and ships as a kit that includes a clamp. Over time, normal wear and tear, exposure to high water pressure or temperature, or physical damage from kinks and pinches can cause the hose to crack, bulge, or leak. A failing drain hose typically shows up as water leaking around the hose connections or along its length, slow or improper draining, or visible cracks and bulges in the hose material. It directly replaces W10221546, W10769870, W10821090, W11203364, W11249137, W10826733, W11199768, W11199820, AP6339776, and PS12578897. Quick Answer The W11244231 Genuine OEM Whirlpool Washer Drain Hose fixes Whirlpool, Maytag, Kenmore, Amana, Crosley, Admiral, Inglis, and Roper washers with a cracked, bulging, or leaking drain hose, slow draining, or a missing hose. Approximately 4 feet long, includes clamp. Replaces W10221546, W10769870, W10821090, W11203364, W11249137, W10826733, W11199768, W11199820, AP6339776, PS12578897. This is a separate part from our W11281268 drain hose listing, which fits a different set of washer models — always confirm your exact model number before ordering. Common Problems This Part Fixes Water leaking around the hose connections or along its length Slow draining or improper drainage of the tub Visible cracks, bulges, or damage to the hose material Missing drain hose on a newly acquired or moved washer Reduced washer efficiency from a clogged, worn, or damaged hose Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer drain hose directly replaces the following OEM and cross-reference part numbers: W11244231, W10826733, W10221546, 4814009, W10769870, W10821090, W11199768, W11199820, W11203364, W11249137, AP6339776, AWP43752, OEM19019337, PD00045186, PS12578897 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This drain hose is compatible with select Whirlpool washers, and also fits select Maytag, Kenmore, Amana, Crosley, Admiral, Inglis, and Roper washers built on the Whirlpool platform, spanning Whirlpool series 1CWTW4, 2DWTW, 3DWTW, 3LWTW, 3NWTW4800, 3SWTW4800, and 4GWTW, and Maytag series 3LMVWC, 4GMVW, 4KMVW, 4KNTW, 7MMVW, and MVWX6, including specific model numbers such as: MVWX655DW1, NTW4516FW3, VAW3584GW0 WTW4816FW2, WTW5000DW1, WTW5000DW2, WTW5000DW3, WTW9500EC0 WTW5100HC0, WTW5500BW0, WTW5600XW0, WTW5700AC0, WTW5800BC0, WTW6120HC0 WTW7000DW0, WTW8000DW0 ITW4871FW0, ITW4871FW1, ITW4871FW2 4KMVWC415FW0, 4KMVWC430JW0, 7MWTW1504DQ0 Kenmore 11026112310 Note — not the same as W11281268: This is a separate part from our W11281268 drain hose listing, which fits a different set of Whirlpool, Maytag, and Amana washer models with its own cross-reference set. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure which hose your washer needs. Key Features Genuine Whirlpool OEM part — factory-specified length and fitting design Carries wastewater from the washer to your house drain during the drain cycle Resolves "leaking around connections," "slow draining," and "cracked or bulging hose" symptoms Approximately 4 feet long Ships as a kit including a clamp Direct drop-in replacement — matches the original fitting and length Replaces W10221546, W10769870, W10821090, W11203364, W11249137, W10826733, W11199768, W11199820, AP6339776, and PS12578897 Compatible with Whirlpool, Maytag, Kenmore, Amana, Crosley, Admiral, Inglis, and Roper washers Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number W11244231 Part Type Washer Drain Hose Kit Condition Genuine OEM Brand Whirlpool Length Approx. 4 feet Includes Clamp Related Part W11281268 (6' hose, different model fitment, sold separately) Repair Difficulty Easy — basic hand tools, novice repair experience Quantity 1 drain hose kit Compatible Brands Whirlpool, Maytag, Kenmore, Amana, Crosley, Admiral, Inglis, Roper Installation Notes ⚠️ Unplug Washer And Shut Off Water Supply Before Starting — Transfer Your Old Clamps To The New Hose Disconnect power at the outlet, or shut off the house circuit breaker for the appliance, and shut off the water supply before beginning. Wear work gloves. Remove the back panel of the washer, then the lower front access panel to access the drain hose connection. Place a towel down before disconnecting any hoses to catch any remaining water. Disconnect the old hose from the washer's outlet spout and from your standpipe or drain connection. Transfer your existing hose clamps onto the new W11244231 hose during installation. Fit the new hose over the outlet spout and secure the clamp, then reconnect the other end to your house drain. Reinstall the lower front access panel and back panel. Restore the water supply and power, then run a test cycle to confirm the hose is secure with no leaks. Tools needed: multi-screwdriver, standard pliers, work gloves, towel. Frequently Asked Questions My washer is leaking. Is this the right part? It's worth checking, especially if the leak appears to come from around the hose connections or along its length rather than from the washer's tub or valve area. A cracked, bulging, or worn drain hose is a documented cause of leaking and can be resolved by replacing the hose to restore proper drainage. Is this the same as your W11281268 listing? No, these are two separate genuine Whirlpool drain hoses that fit different sets of washer models, with their own distinct cross-reference lists. Always confirm your exact model number against the compatibility list for each listing rather than assuming either hose is a universal fit. Do I need to buy new hose clamps separately? This hose kit includes a clamp, but you'll still need to transfer your existing clamps from the old hose for any connections that don't come with a new one included. Keep your old hardware on hand during the swap rather than discarding it with the old hose. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by Whirlpool to factory specifications — guaranteed fit, materials, and performance. It matches the original length and fitting configuration of the drain hose originally installed on your washer. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

EXPW79SC (4 Pack) Washing Machine Fill Hose Gasket with Screen 4 Pack compatible with 5/ 8 inch washing machine and 3/4 inch garden hose Fine Screen the rubber washer with stainless steel filter mesh, serves as a flow restrictor can reduce the waste of water effectively     

Read more less

XPARTCO 279393 Dryer Terminal Block Screw Kit The XPARTCO 279393 is an aftermarket replacement terminal block screw kit compatible with a wide range of Whirlpool-family electric dryers including Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Roper, Admiral, Estate, Crosley, Inglis, Magic Chef, and Norge. The terminal block screws secure the dryer power cord wires to the terminal block — the connection point where 240V power enters the dryer. Loose, corroded, or damaged screws at this connection can cause intermittent power loss, blown fuses, tripped breakers, or dangerous arcing. This kit includes 3 chrome-plated screws and 3 nuts — everything needed to restore a secure, conductive connection at the terminal block. The chrome plating improves electrical conductivity and corrosion resistance. Screws measure 7/16" L x 7/16" W x 11/16" H; nuts measure 1/2" L x 1/2" W x 1/8" H. Installs in under 15 minutes with basic hand tools. Quick Answer The XPARTCO 279393 Terminal Block Screw Kit fixes electric dryers with intermittent power, blown fuses, tripped circuit breakers, hot terminals, or visible arcing and scorching at the power cord connection. Includes 3 chrome-plated screws and 3 nuts. Compatible with Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Roper, Admiral, and more. Common Problems This Part Fixes Dryer has intermittent power or will not start at all Internal fuses repeatedly blowing without another clear cause Circuit breaker for the dryer repeatedly tripping Terminal block area is hot to the touch during or after operation Visible arcing, sparks, scorch marks, or smoke around the terminal block cover Heating element or motor works intermittently but not consistently Dryer power cord connection is loose, corroded, or visibly damaged Replaces Part Numbers This terminal block screw kit directly replaces the following OEM and cross-reference part numbers: 279393, 279393D, 279393VP, 3184, EAP334188, AWP39844, PD00003883, AH334188, EA334188, AP3020386, PS334188 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This terminal block screw kit is compatible with select electric dryers from the following brands: Whirlpool electric dryers Kenmore / Sears electric dryers (Whirlpool-built models) Maytag electric dryers KitchenAid electric dryers Amana electric dryers Roper electric dryers Admiral electric dryers Estate electric dryers Crosley electric dryers Inglis electric dryers Magic Chef, Norge, and Jenn-Air electric dryers Note: This kit is for electric dryers only. Gas dryers do not use a terminal block for power cord connections. Key Features Secures the dryer power cord wires to the terminal block for a safe, reliable 240V connection Kit includes 3 screws and 3 nuts — one complete set for all three terminal positions Chrome-plated metal construction — improves electrical conductivity and resists corrosion Screw dimensions: 7/16" L x 7/16" W x 11/16" H; Nut dimensions: 1/2" L x 1/2" W x 1/8" H Direct replacement for OEM part numbers 279393, 279393D, and 279393VP — no modification required Compatible with Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Roper, Admiral, and more Aftermarket replacement built to OEM-equivalent quality standards Quick DIY repair — installs in under 15 minutes with basic hand tools Product Specifications Part Number 279393 Part Type Terminal Block Screw and Nut Kit Condition Aftermarket Replacement Application Electric Dryers (240V terminal block) Kit Contents 3 chrome-plated screws and 3 nuts Screw Dimensions 7/16" L x 7/16" W x 11/16" H Nut Dimensions 1/2" L x 1/2" W x 1/8" H Material Chrome-plated metal Compatible Brands Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Roper, Admiral, Estate, Crosley, Inglis, Magic Chef, Norge, Jenn-Air Dryer Type Electric dryers only ⚠️ Electrical Safety Warning This kit connects the power cord to the dryer's terminal block — a high-voltage connection carrying 240V. Always unplug the dryer and shut off the circuit breaker before beginning installation. Loose or improperly tightened terminal screws can cause arcing, overheating, blown fuses, or fire. If you are not comfortable working with high-voltage electrical connections, have this part installed by a qualified appliance technician. Installation Notes ⚠️ Unplug and Switch Off Breaker Before Starting Unplug the dryer from the wall outlet and turn off the circuit breaker for the dryer before beginning any work on the terminal block. Locate the terminal block cover plate on the back of the dryer and remove it by unscrewing the retaining screw. Use needle-nose pliers to carefully disconnect the power cord wires from the terminal block. Remove the old screws and nuts using a Phillips or flat-head screwdriver. Install the new 279393 screws and nuts into the terminal block. Reconnect the power cord wires to the correct terminals — refer to the label inside the terminal block cover or your dryer's wiring diagram to confirm wire positions. Tighten all screws firmly but do not overtighten. Replace the terminal block cover plate. Restore power and run a test cycle to verify correct operation. Tip: While the cover is off, inspect the terminal block itself (part 694431) for burn marks or damage. If the block is damaged, replace it before reinstalling. Tools needed: Phillips screwdriver, flat-head screwdriver, needle-nose pliers. Frequently Asked Questions What is the terminal block screw kit used for? The terminal block screw kit secures the three wires of the dryer's power cord (two hots and a neutral, or two hots and a ground depending on cord type) to the terminal block at the back of the dryer. This is the point where 240V power enters the machine. The screws must be firmly tightened to maintain a safe, low-resistance electrical connection. If they loosen or corrode over time, resistance increases at the connection — causing heat, arcing, blown fuses, or power loss. Can I also use this kit when installing a new dryer power cord? Yes — this kit is commonly needed when installing a new 3-wire or 4-wire dryer power cord. When switching from a 3-wire to 4-wire cord (or vice versa), the terminal block screws and nuts often need to be loosened and retightened, and replacing them with a fresh set ensures a secure, corrosion-free connection from the start. Should I also inspect the terminal block itself? Yes. While the terminal block cover is off, inspect the block itself (part 694431) for burn marks, melted plastic, or damaged terminals. If the block shows any of these signs, it should be replaced before reinstalling — new screws alone cannot fix a damaged terminal block. Contact our support team to find the correct terminal block for your model. Does this kit work for gas dryers? No. Gas dryers use a standard 120V three-prong household plug and do not have a terminal block for power cord connections. The 279393 kit is for electric dryers only, which use a 240V outlet and require a hard-wired terminal block connection for the power cord. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is made from chrome-plated metal to match the dimensions and electrical performance of the original 279393 screw kit. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout  

Read more less

XPARTCO DC66-00887A Washer Pulsator Cap – Compatible with Samsung Washers Product Description Replace your worn or missing washer pulsator cap with the XPARTCO DC66-00887A Washer Pulsator Cap. This high-quality aftermarket replacement protects the central bolt of the pulsator (wash plate) from water intrusion and corrosion. A damaged or missing cap can lead to imbalance, leaks, or noise during spin cycles. Installing this part restores proper drum function and extends the washer’s lifespan. Replaces Part Numbers DC66-00887A, PD00038471, EAP11762121, AP6027557, 4814077, PS11762121. Compatibility This replacement pulsator cap fits select Samsung top-load washers. Example compatible models include (but are not limited to):Samsung WA45H7000AW/A2, WA400PJHDWR/AA, WA422PRHDWR/AA Always verify your washer’s model number before ordering. Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement – Compatible with Samsung top-load washers 💧 Protective Design – Prevents water from reaching the pulsator bolt 💰 Budget-Friendly Fix – Quality replacement at a lower cost than OEM 🛠️ Simple Installation – Snaps securely into place in seconds 🛡️ Fixes Common Issues – Resolves missing, cracked, or leaking pulsator caps 📐 Product Specification Part Number: DC66-00887A Component Type: Washer Pulsator (Wash Plate) Cap Material: Durable, water-resistant plastic Mounting: Snap-fit installation, tool-free Operating Conditions: Designed for residential top-load washers Compliance: Built to OEM-equivalent quality standards (not OEM) 🛠️ Installation Notes Tools Needed: None ⚠️ Safety First: Always unplug the washer before performing repairs. Steps: Unplug washer and open lid. Remove any debris around the pulsator area. Gently pry off the old cap using a flathead screwdriver if needed. Align and press the new XPARTCO DC66-00887A cap firmly until it clicks. Confirm a tight seal before restarting the washer. ⏱️ Time Required: 5 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders 🛠️ Trusted Appliance Parts Supplier 🔄 30-Day Return Policy Restore your washer’s performance — Add to Cart Now for a reliable, affordable replacement!

Read more less

Genuine Whirlpool 8212546RP Washer Fill Hoses 2-Pack 4 Feet - Compatible with Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Kenmore Product Description Ensure reliable water supply for your washer with the Genuine Whirlpool 8212546RP Washer Fill Hoses 2-Pack. These OEM 4-foot black rubber hoses are designed for Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, and Kenmore washing machines, delivering hot and cold water with anti-corrosive brass couplings and pre-installed high-quality EPDM washers. With a 1050 PSI burst strength, they prevent leaks and ensure consistent water flow, addressing issues like leaking, low water flow, or hose failure. Note: Includes two 4-foot hoses with built-in O-rings. Disconnect power and water supply before installation. Replace hoses every 5 years to reduce the risk of failure. Replaces part numbers: 8212546RP, AP3885155, 1178876, 49535, 8212546IP, 8212546RW, PS1156134. Compatibility: Compatible with models including but not limited to: Whirlpool: WFW72HEDW0, WFW75HEFW0, WFW90HEFC0, WTW5000DW0 Maytag: MHW3500FW0, MHW5500FC0, MVWC565FW0, MVWB835DW0 KitchenAid: KSMW1030SS0 Jenn-Air, Amana, Kenmore: (select models, verify compatibility) Verify your model number or contact our support team for assistance. Key Features: ✅ Brand and Models Compatibility: Fits select Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, and Kenmore washing machines. 💧 Specifications: OEM 4-foot black rubber hoses with brass couplings, 1050 PSI burst strength, and EPDM washers. 💪 Reliable Performance: Authentic Whirlpool part ensures long-lasting durability and leak-free operation. 🛠️ Easy Installation: Requires pliers and work gloves; typically installed in 10–15 minutes. 🛡️ Effective Fixes: Resolves leaking, low water flow, or hose failure issues. Product Specification Part Number: Genuine Whirlpool 8212546RP Component Type: Washer fill hoses (2-pack) Material: Black rubber with brass couplings, EPDM washers Dimensions: 4 ft. length. Mounting: 3/4" male and female connections with built-in O-rings Operating Conditions: Suitable for hot and cold water in household washing machine environments Compliance: Exceeds IAPMO, CSA, ANSI, IEC 61770, and RMA standards; Prop 65 warning for California Installation Notes: Safety First: Disconnect the washer from the power source and turn off hot and cold water supplies before installation. Shop for high-quality Genuine appliance parts with a 30-day return policy. Keep your washer running efficiently today! Add to cart now for a reliable fix!

Read more less

EXPW79SC (8 Pack) Washing Machine Fill Hose Gasket with Screen 8 Pack compatible with 5/ 8 inch washing machine and 3/4 inch garden hose Fine Screen the rubber washer with stainless steel filter mesh, serves as a flow restrictor can reduce the waste of water effectively     

Read more less