Dryer Repair Kit

XPARTCO 4392065 Dryer Maintenance Kit Replaces 349241T, 341241, WP691366 The XPARTCO 4392065 is an aftermarket dryer maintenance and repair kit containing the three most commonly replaced drum drive components for Whirlpool-family 29-inch dryers including Whirlpool, Kenmore, Maytag, Amana, KitchenAid, Roper, Admiral, Estate, Crosley, Inglis, and Magic Chef. The kit includes the drum belt (341241), idler pulley (691366), and rear drum support roller kit (349241T) — the three parts that work together to drive and support the dryer drum, and that most frequently cause squealing, thumping, no heat, and drum-not-spinning issues when worn. Replacing all three parts together in a single repair is the recommended approach — since these components wear at similar rates and the dryer must be fully disassembled to access any one of them, doing all three at once saves significant time and cost compared to replacing them individually. The kit contains everything needed: 1 drum belt, 1 idler pulley, 2 drum support rollers, 4 tri-rings, and 2 retaining washers. Installs in 45–60 minutes with basic hand tools. Quick Answer The XPARTCO 4392065 Dryer Maintenance Kit fixes squealing, thumping, no heat, and drum-not-spinning issues in Whirlpool-family 29" dryers in a single repair. Includes 1x 341241 drum belt (92-1/4" x 1/4", 4 ribs), 1x 691366 idler pulley, 2x 349241T drum rollers, 4x tri-rings, and 2x retaining washers. Compatible with Whirlpool, Kenmore, Maytag, Amana, KitchenAid, Roper, Admiral, Estate, Crosley, Inglis, and Magic Chef dryers. Common Problems This Kit Fixes Loud squealing, squeaking, or thumping noise during the drying cycle Dryer drum not spinning — motor runs but belt has broken Clothes not tumbling or drying properly Grinding or rumbling noise from the drum area Dryer drum spinning unevenly or stopping intermittently Belt repeatedly slipping or breaking due to worn idler pulley Drum vibrating excessively due to worn roller bearings What's in the Kit Part 1 of 3 — 1 included 341241 Dryer Drum Belt 92-1/4" L x 1/4" W · 4 ribs, 3 grooves · Neoprene rubber · Wraps around the drum and connects to the idler pulley and motor pulley to drive drum rotation Part 2 of 3 — 1 included 691366 Idler Pulley Sturdy plastic with metal shaft and idler arm · Maintains correct tension on the drum belt between the motor and drum · Self-lubricating bearing Part 3 of 3 — 2 included 349241T Rear Drum Support Roller Kit 2 drum rollers · Reinforced self-lubricating metal bearings, thickened rubber wheel · Supports the rear of the drum as it rotates · Includes 4 tri-rings and 2 retaining washers Replaces Part Numbers Kit (4392065) cross-references: 4392065, 2014, 26000279435, 26000279436, 279435, 279436, 279708, 279708MS, 279709, 279709MS, 279860, 279948, 4392065VP, 587636, 80046, 8106, 8237, 8238, AWP39348, PD00002464, AH373087, EA373087, AP3131942, PS373087. 341241 Belt cross-references: 341241, 14210003, 2008, 26000341241, 26000349533, 31001026, 31531589, 3389628, 3392665, 3394651, 3399844, 341241VP, 345473, 349533, 529597, 53-0186, 53-1080, 53-1086, 53-1528, 53-1589, 53-2671, 53-2910, 660996, 660997, 661561, 693306, 694088, 694416, 694868, 695055, 697388, 8066065, 8206, 8210, 920H4, 920H5, 99906951, 99989673, 99989674, FSP341241, LB276, LB279, P46-037, P46-149, W10127457, W10131364, AH346995, AP32, EA346995, ER341241, AP2946843, PS346995, TJ341241. 691366 Idler Pulley cross-references: WP691366, 691366, 239477, 26000691366, 3346, 337116, 337407, 337510, 3388345, 338946, 3394332, 347034, 347226, 347277, 4319391, 688166, 691366BULK, 8207, 99989677, DE412, K35-163, W10612905, AP6010582, PS11743765. 349241T Drum Roller cross-references: 349241T, 26000349241, 337089, 3389901, 3397588, 3397590, 340352, 3436, 349241, 349241TVP, 661562, 8170, 8205, 99989678, 99989679, AH347627, EA347627, K34-895, AP3098345, PS347627. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This kit is compatible with select 29-inch large-capacity gas and electric dryers from the following brands: Whirlpool dryers (gas and electric) Kenmore / Sears dryers (select Whirlpool-built models) Maytag dryers (gas and electric) Amana dryers KitchenAid dryers Roper dryers Admiral dryers Estate dryers Crosley dryers Inglis dryers Magic Chef dryers Note: This kit is designed for 29-inch large-capacity Whirlpool-family dryers. If your dryer is a compact or stackable model, verify compatibility with our support team before ordering. Key Features Three-part kit addresses the most common drum drive failures in a single repair — saves time and cost vs. replacing parts individually Belt: 92-1/4" x 1/4", 4 ribs, 3 grooves — premium neoprene rubber resists cracking, heat, and stretching Idler pulley: sturdy plastic with metal shaft and self-lubricating bearing — maintains correct belt tension Drum rollers: 2 included — reinforced self-lubricating metal bearings and thickened rubber wheels for quiet, stable drum support All hardware included: 4 tri-rings and 2 retaining washers — everything needed for complete installation Since the dryer must be disassembled to access any one of these parts, replacing all three at once eliminates repeated teardowns Compatible with 11 major appliance brands on the Whirlpool 29-inch platform Aftermarket replacement built to OEM-equivalent quality standards DIY repair — installs in 45–60 minutes with basic hand tools Product Specifications Kit Part Number 4392065 Condition Aftermarket Replacement Application 29-inch Gas and Electric Dryers Kit Includes 1x 341241 Drum Belt, 1x 691366 Idler Pulley, 2x 349241T Drum Rollers, 4x Tri-rings, 2x Retaining Washers Belt Length 92-1/4 inches Belt Width 1/4 inch Belt Ribs 4 ribs, 3 grooves Belt Material Neoprene rubber Idler Pulley Material Plastic / Metal Drum Roller Quantity 2 rollers (replace both at same time) Roller Lubrication Self-lubricating bearings — no grease needed Compatible Brands Whirlpool, Kenmore, Maytag, Amana, KitchenAid, Roper, Admiral, Estate, Crosley, Inglis, Magic Chef Installation Notes ⚠️ Unplug Dryer Before Starting Disconnect power (and shut off gas for gas dryers) before beginning. Remove the lint screen and unscrew the Phillips screws inside the lint screen housing. Use a putty knife to release the top panel clips and lift the top panel. Remove the front panel to access the drum. Release belt tension at the idler pulley, then lift the drum out. Remove the old belt, idler pulley, and drum rollers. Install the 2 new 349241T rollers onto the rear bulkhead shafts, pressing the new tri-rings and washers into place. Install the new 691366 idler pulley onto the idler arm. Loop the new 341241 belt around the drum with the ribbed side facing inward, then route it around the idler pulley and motor pulley. Reinstall the drum, reassemble the front and top panels, and restore power. Run a test cycle to confirm quiet operation. Tools needed: Phillips screwdriver, 1/4" nut driver, putty knife, needle-nose pliers, flat pry tool. Frequently Asked Questions Why should I replace all three parts at the same time? The drum belt, idler pulley, and drum support rollers all work together as a system and wear at similar rates under the same conditions. Since the dryer must be fully disassembled to access any one of these parts, replacing all three in a single repair is far more cost-effective than replacing them one at a time — which would require three separate teardowns. This is the same reason the 4392065 maintenance kit was designed: one repair, all three parts, done. What does each part in this kit do? The 341241 drum belt wraps around the outside of the drum and connects to the idler pulley and motor pulley — the motor drives the belt, which spins the drum. The 691366 idler pulley maintains tension on the belt so it grips the drum and motor pulley properly. The 349241T drum rollers are support wheels mounted on the rear of the dryer that cradle and support the back edge of the drum as it rotates. All three are essential to smooth, quiet drum operation. How is this kit different from the 4392067 repair kit? The 4392065 and 4392067 kits are designed for different Whirlpool-family dryer generations. The 4392065 uses the 341241 belt (92-1/4" x 1/4", 4 ribs) and the 691366 idler pulley, and is for older 29-inch Whirlpool-family dryers. The 4392067 uses the 661570V belt (93-1/2" x 1/4", 4 ribs) and the W10837240 idler arm assembly, and is for newer Whirlpool-family dryers (those with the lint screen inside the door). Use your model number to confirm which kit fits your specific dryer before ordering. Do I need to lubricate the drum rollers after installing? No — the 349241T drum rollers include self-lubricating bearings and do not require any additional grease or oil after installation. Applying grease to self-lubricating rollers is not recommended and can actually attract lint and debris, causing the rollers to wear faster. Is this an OEM or aftermarket kit? This is an aftermarket replacement kit built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM kit, but all three included components are manufactured from premium neoprene rubber, durable plastic, and metal to match the dimensions and performance of the original 4392065 kit parts. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

EXP694 Dryer Repair Kit Replaces DC97-16782A, 6602-001655, DC93-00634A The EXP694 Dryer Repair Kit is a complete drum system rebuild solution designed to restore smooth, quiet, and efficient dryer operation. This kit includes the most common wear components found inside your dryer: drum belt, idler pulley, and drum support rollers. Over time, these parts wear down together, causing squeaking, grinding, drum slippage, or complete failure to spin. Replacing all components at once ensures proper alignment, eliminates noise, and prevents repeat breakdowns — making this the most effective long-term repair solution. Quick Answer The EXP694 Dryer Repair Kit fixes dryers that won’t spin, make loud squeaking or grinding noises, or stop tumbling. It replaces the belt, rollers, and idler pulley to restore smooth and quiet drum operation. Note: Includes four rollers (each with shaft and two tri-rings), one idler pulley, and one belt. Replace all four rollers for even wear. Inspect the drum and felt seal (e.g., DC97-07618A) for wear. Clean lint from the drum and cabinet to prevent overheating. Common Problems This Part Fixes Dryer drum not spinning or slipping Loud squeaking, grinding, or thumping noises Uneven or slow drum rotation Dryer stopping mid-cycle Excessive vibration or instability Worn belt, rollers, or idler pulley components Replaces Part Numbers This repair kit replaces the following common drum system components: Drum Roller: DC97-16782A, AP5325135, DC97-16782C, DC97-16782D, 2027851, DC97-07523A, DC97-07523B, PS4221885, WPW10177428, AP6016361, W10177428, 35001136, DC97-07523A, PS11749648 Idler Pulley: DC93-00634A, AP6038887, DC96-00882C, DC61-01230B, DC96-00882B, PS11771601, 12002777, AP4010261, 1401171, 35001083, 35001098, 35001276, AH2004052, DC61-01215A, DC96-00882B, EA2004052, PS2004052 Drum Belt: 6602-001655, AP4373659, 1935594, 6602-001314, PS4133825, WPW10205415, AP6017004, W10205415, 35001137, 6602-001314, PS11750299 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This repair kit is compatible with select dryers from the following brands: Samsung dryers (gas and electric models) Kenmore / Sears dryers (select models built on Samsung platform) Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Complete drum repair kit including belt, rollers, and idler pulley OEM-equivalent fit, performance, and durability Eliminates noise and restores smooth drum rotation Prevents repeat repairs by replacing all wear components together Cost-effective all-in-one repair solution DIY-friendly installation with basic tools Product Specifications Includes 4 drum rollers (DC97-16782A, ~3-1/4" diameter x 1-1/8" width, blue/black plastic/rubber, metal shaft, self-lubricating bushing with ball bearing, each with shaft and two tri-rings), 1 idler pulley (DC93-00634A, metal/plastic), 1 drum belt (6602-001655, 92" long, 5 ribs, neoprene), kit dimensions ~10"L x 6"W x 4"H. Part Type Dryer Repair Kit Includes Belt, Rollers, Idler Pulley Application Dryer Drum System Condition Aftermarket Replacement Compatible Brands Samsung, Kenmore Installation Notes ⚠️ Safety First — Unplug Dryer Before Starting Disconnect power before servicing. Remove dryer panels, release belt tension, and replace worn components. Ensure proper alignment of the belt and rollers before reassembly. For best results, replace all components included in this kit at the same time. Frequently Asked Questions Should I replace all parts at once? Yes. The belt, rollers, and pulley wear together. Replacing all components ensures smooth operation and prevents future breakdowns. Will this fix dryer noise? Yes. This kit resolves most squeaking, grinding, and thumping noises caused by worn drum components. Is this an OEM part? This is a high-quality aftermarket repair kit built to OEM-equivalent standards for performance and durability. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XP311 Dryer Thermostat Kit – Replacement for LG 6931EL3003D, 6323EL2001B, and 6931EL3001E Product Description Restore proper temperature control and dryer performance with the XP311 Dryer Thermostat Kit, designed as a high-quality aftermarket replacement for LG thermostats 6931EL3003D, 6323EL2001B, and 6931EL3001E. This kit includes multiple thermostats and thermal fuses that regulate and protect against overheating. A failing thermostat can lead to no-heat, poor drying, or overheating issues. Replacing it with this reliable kit ensures safe, consistent drying performance. Replaces Part Numbers 6931EL3003D, 1268366, AH3530485, EA3530485, PD00001818, EAP3530485, AP4440975, PS3530485, 6323EL2001B, 1268206, 6323EL2001H, AH3529026, PD00001821, EAP3529026, EA3529026, AP4441539, PS3529026, 6931EL3001E, 1268363, 6931EL3001C, PD00023869, EAP3530481, AH3530481, EA3530481, AP4440977, PS3530481. Compatibility This replacement thermostat kit is compatible with select LG and Kenmore dryers. Example compatible models include (but are not limited to): LG DLE5955G, LG DLE2516W, and Kenmore 796.81022900. Always verify your dryer’s model number before ordering. Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement Kit – Designed to match LG thermostat set specifications 🌡️ Temperature Regulation – Maintains safe and consistent dryer heat levels 💰 Cost-Effective Bundle – Includes multiple thermostats and thermal fuses for one low price 🛠️ DIY Friendly – Installs easily with basic tools and clear wire connections 🛡️ Fixes Common Issues – Solves dryers not heating, overheating, or shutting off mid-cycle 📐 Product Specification Part Number: XP311 Component Type: Dryer Thermostat and Thermal Fuse Kit Material: Metal thermostat housing and heat-resistant plastic connectors Mounting: Direct-fit replacement Operating Conditions: Designed for residential electric dryers Compliance: Built to OEM-equivalent standards (not OEM) 🛠️ Installation Notes Tools Needed: Phillips screwdriver, nut driver, needle-nose pliers ⚠️ Safety First: Always unplug dryer before starting repairs to avoid electrical shock. Steps: Disconnect dryer from power. Remove rear access panel to expose heater housing. Identify and disconnect faulty thermostats or fuses. Install the new XP311 thermostat kit components using existing screws. Reconnect wiring harnesses securely. Restore power and test the dryer for proper heating function. ⏱️ Time Required: 20–30 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders 🛠️ Trusted Appliance Parts Supplier 🔄 30-Day Return Policy Restore consistent heat and drying performance — Add to Cart Now for a reliable, budget-friendly repair solution!

Read more less

4392067 Genuine OEM Whirlpool Dryer Repair Kit — Belt, Rollers & Idler (27") The 4392067 is a Genuine OEM Whirlpool dryer maintenance and repair kit that contains all the components most commonly replaced when a 27-inch Whirlpool-family dryer becomes noisy, stops tumbling, or starts vibrating — specifically the drum drive belt, all four drum support rollers, the idler pulley, tri-ring retaining clips, a washer, and installation instructions. Installing all of these components together in a single repair restores smooth, quiet drum rotation and eliminates the most common causes of dryer noise and drum drive failure in one visit. As a Genuine OEM kit assembled by Whirlpool to factory specifications, the 4392067 includes the belt (661570V), four rollers (WPW10314173), idler pulley (279640), nine tri-rings, one washer, and instructions. Compatible with 27-inch Whirlpool, Kenmore 110-series, Maytag, Roper, Estate, Crosley, Amana, and Admiral dryers built in 1965 or later. Important: the included belt (661570V, 93-1/2" x 1/4", 4-rib) is correct for many models but does not fit all — verify that 661570V is the correct belt for your specific model before ordering. It directly replaces AP3109602, 2015, 4392067VP, 587637, 80047, AH373088, EA373088, EAP373088, and PS373088. Installs in 45–60 minutes with basic hand tools. Quick Answer The 4392067 Genuine OEM Whirlpool Dryer Repair Kit fixes 27-inch Whirlpool-family dryers that are squealing, thumping, rumbling, or where the drum has stopped spinning. All-in-one kit: belt 661570V + 4 rollers (WPW10314173) + idler pulley (279640) + 9 tri-rings + washer + instructions. Genuine OEM. Important: belt 661570V fits many but not all models — verify your belt part number before ordering. Replaces AP3109602, 2015, 4392067VP, 587637, PS373088. Common Problems This Kit Fixes Loud squealing, squeaking, or thumping noise during the drying cycle Rumbling or grinding noise — worn drum support rollers Drum not spinning — broken or stretched drive belt Motor running but drum still — belt has snapped Belt repeatedly slipping — worn idler pulley no longer maintaining belt tension Burning rubber smell — slipping belt from a failed idler pulley Extended drying times — drum not rotating at correct speed due to belt or roller wear Excessive vibration during the drying cycle What's in the Kit Part 1 Drum Drive Belt — 661570V 93-1/2" long x 1/4" wide · 4-rib profile · Wraps around the drum and connects to the motor pulley and idler pulley to spin the drum · Important: 661570V is correct for many but not all compatible models — verify this belt number fits your specific dryer before ordering Parts 2–5 (qty: 4) Drum Support Rollers — WPW10314173 (set of 4) Cylindrical rubber-and-plastic wheels that support the drum rim as it rotates · LG/Whirlpool 27" dryer platform · Replace all 4 at the same time for even drum support Part 6 Idler Pulley Assembly — 279640 Spring-tensioned pulley wheel that presses against the drive belt to maintain correct belt tension · Pulley wheel only (not the arm) — mounts on the existing idler arm inside the dryer Hardware 9 Tri-Ring Retaining Clips + 1 Washer + Instructions Tri-ring clips secure the drum rollers to their mounting shafts · Washer provides proper spacing at roller shaft · Instruction sheet included Replaces Part Numbers This dryer repair kit directly replaces the following OEM and cross-reference part numbers: 661570V, 279640, WPW10314173, 8536974, 4392067, 2015, 4392067VP, 587637, 80047, AH373088, EA373088, AWP39353, EAP373088, PD00002451, AP3109602, PS373088. Contact our support team with your model number if you need confirmation before ordering. Compatibility This repair kit is compatible with 27-inch gas and electric dryers from the following brands (built 1965 or later): Whirlpool dryers (27" WED, WGD, Cabrio, Duet, and related series) Kenmore / Sears dryers — 110-series (Whirlpool-built models) Maytag dryers (Bravos XL and related series) Roper dryers Estate dryers Crosley dryers Admiral dryers Amana dryers (select models) Important — Belt Compatibility: The belt included in this kit is part number 661570V (93-1/2" x 1/4", 4-rib). This belt is correct for many 27-inch Whirlpool-family dryers but does not fit all compatible models. Before ordering, verify that 661570V is the correct belt part number for your specific dryer model. If your dryer uses a different belt, the rollers and idler pulley in this kit will still fit, but you will need to order the correct belt separately. Key Features Genuine OEM kit assembled by Whirlpool — all components manufactured to factory specifications All-in-one repair: belt (661570V) + 4 rollers (WPW10314173) + idler pulley (279640) + tri-rings + washer + instructions in a single box Replaces all the most commonly worn drum drive components in a single repair — eliminates the need for separate part orders and multiple teardowns For 27-inch Whirlpool-family dryers built 1965 or later Belt 661570V: 93-1/2" long x 1/4" wide, 4-rib — verify fit for your model before ordering Idler pulley (279640) is the pulley wheel only — mounts on the existing idler arm Compatible with Whirlpool, Kenmore 110-series, Maytag, Roper, Estate, Crosley, Admiral, and Amana Installs in 45–60 minutes with basic hand tools Product Specifications Kit Part Number 4392067 Condition Genuine OEM Application 27-inch Gas and Electric Dryers (built 1965 or later) Belt Included 661570V — 93-1/2"L x 1/4"W, 4-rib (verify fit for your model) Rollers Included 4x WPW10314173 drum support rollers Idler Pulley Included 279640 (pulley wheel only — not the arm) Hardware Included 9 tri-ring retaining clips, 1 washer, instructions Compatible Brands Whirlpool, Kenmore, Maytag, Roper, Estate, Crosley, Admiral, Amana Installation Notes ⚠️ Unplug Dryer Before Starting Disconnect power (and shut off gas for gas dryers) before beginning. Remove the top panel by inserting a putty knife under the front edge to release the spring clips, then lift. Remove the front panel to fully expose the drum. Take a photo of the existing belt routing before removing anything. Release the drive belt from the idler pulley and slide it off the drum. Remove the drum and set it aside. Replace all four drum support rollers — remove the old tri-ring clips with needle-nose pliers, slide the old rollers off the shafts, and install the new WPW10314173 rollers with new tri-rings and the included washer. Replace the idler pulley (279640) by pressing the new wheel onto the idler arm shaft. Route the new 661570V belt around the drum (ribbed side against the drum), under the idler pulley, and around the motor pulley. Reinstall the drum, front panel, and top panel. Restore power and run a test cycle. Tools needed: Phillips screwdriver, putty knife, needle-nose pliers, socket set. Frequently Asked Questions How do I know if the belt in this kit (661570V) fits my dryer? The belt included in this kit is 661570V (93-1/2" long, 1/4" wide, 4-rib). To confirm it is correct for your dryer, look up your dryer's model number in an online parts diagram and check the belt part number listed. If the parts diagram shows 661570V or its cross-reference 661570, this kit's belt is correct. If your diagram shows a different belt part number — for example 341241, W10205415, or WP8547157 — the rollers and idler in this kit will still fit your dryer, but you will need to order the correct belt separately. This is the most important compatibility check before purchasing this kit. Is the idler pulley (279640) a complete arm assembly or just the wheel? The 279640 included in this kit is the pulley wheel only — it does not include the idler arm or bracket. It presses onto the existing idler arm shaft inside your dryer. If the idler arm itself is cracked or broken, the arm assembly will need to be replaced separately. On most Whirlpool 27-inch dryers the arm itself rarely fails — it is the wheel bearing that wears out, which is what the 279640 wheel in this kit addresses. Why should I replace all four rollers instead of just the one that's noisy? All four drum support rollers wear at the same rate through the same number of drying cycles. When one roller starts making noise, the other three have experienced the same wear and are likely close behind. Replacing only the noisy roller leaves three worn rollers supporting the drum unevenly, often leading to a repeat repair within months. Since the dryer is already fully disassembled for this repair, replacing all four at once is the most cost-effective and long-lasting approach. How is the 4392067 kit different from the 4392065 kit? Both are Genuine OEM Whirlpool dryer repair kits but for different dryer platforms. The 4392065 is for older Whirlpool 29-inch dryers with the lint screen on top (contains belt 341241, 2 rollers 349241T, idler pulley 691366). The 4392067 is for newer Whirlpool 27-inch dryers with the lint screen inside the door — typically the Duet, Cabrio, Bravos XL, and Thin Twin platforms (contains belt 661570V, 4 rollers WPW10314173, idler pulley wheel 279640). They are not interchangeable — verify your dryer's lint filter location and model series before ordering. Is this a Genuine OEM or aftermarket part? This is a Genuine OEM kit assembled by Whirlpool to factory specifications. All components — belt, rollers, idler pulley, tri-rings, and washer — are the same parts installed in compatible Whirlpool, Kenmore, Maytag, and related brand 27-inch dryers from the factory. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

EXP653 Dryer Idler Pulley and Belt Set – Replaces 6602-001655, DC93-00634A – Compatible with Samsung & Kenmore Dryers Product Description Restore smooth drum rotation and proper belt tension with the EXP653 Dryer Idler Pulley and Belt Set. This high-quality aftermarket repair kit includes a dryer drum belt and idler pulley, designed to work together to keep the drum turning quietly and efficiently. Worn belts or failing idler pulleys can cause squealing noises, belt slippage, or a drum that won’t rotate. Replacing both components at the same time helps ensure long-lasting performance and prevents repeat breakdowns. EXP653 is an aftermarket solution built to OEM-equivalent specifications, offering reliable performance at a cost-effective price. Replaces Part Numbers Drum Belt Replaces: 6602-001655, 6602-001314, 5PH2337, PD00002012, EXP645, EAP2407938, AP4373659, PS4133825.  Idler Pulley Replaces:  DC93-00634A, DC97-07509B, DC61-01230B, DC96-00882B, DC96-00882C, EXP645, 4455850, PD00032419, EAP11771601, AP6038887, PS11771601. Compatibility This replacement dryer belt and idler pulley set fits select Samsung and Kenmore (Samsung-manufactured) electric dryers. Example compatible models include (but are not limited to): Samsung DV42H5000EW, DV45H7000EW Kenmore 592.89003, 592.89004 Always verify your dryer’s model number before ordering.Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement Set – Designed to match OEM fit and performance 🌀 Restores Smooth Drum Rotation – Ensures proper belt tracking and tension 🔇 Reduces Noise & Vibration – Helps eliminate squealing or grinding sounds 💪 Durable Construction – Reinforced belt and heavy-duty pulley bearing 💰 Cost-Effective Repair – Replaces multiple wear parts in one kit 📐 Product Specification Kit Name: EXP653 Component Type: Dryer Belt & Idler Pulley Set Includes: Dryer drum belt and idler pulley Belt Style: Ribbed, OEM-equivalent length Pulley Type: Bearing-style idler pulley Application: Drum drive and belt tension system Quality Level: Aftermarket replacement (not OEM) 🛠️ Installation Notes Tools Needed: Phillips screwdriver, nut driver, needle-nose pliers ⚠️ Safety First: Always unplug the dryer before servicing to prevent electrical shock. Basic Steps: Disconnect dryer power. Open the cabinet and remove the drum. Remove the worn belt and idler pulley. Install the new EXP653 idler pulley. Route and install the new drum belt correctly. Reinstall the drum, reassemble the dryer, and restore power. Run a test cycle to confirm quiet, smooth operation. ⏱️ Time Required: 30–45 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Aftermarket Appliance Parts 🔄 30-Day Return Policy Fix belt noise and restore smooth dryer operation — Add to Cart Now for a dependable, budget-friendly repair!

Read more less

WE49X21874 Dryer Front Bearing Repair Kit Replaces Part Numbers: WE49X21874, AP5970729, 4379300, PS11700897, WE14M124,  1257069, AH1766010, EA1766010, WE14M106, WE14M120, WG04L00523, AP4297334, PS1766010, WE09X27634, WE09X20441, WE9M30, WE09M0015, WE9M15, AP6889049, PS12722961, WE03X29897, WE12M29, WE12X21574, WE21M29, 559C197P001, 559C197P003, WE03X29897-30PK, WE120122, WE12M0022, WE12M22, WE12M33, AP7012633, PS16542496, WE03X37318, WE1M504, WE01M0333, WE03X37318-50PK, WE1M333, AP7217724, PS17137205, WE03X37317, WE1M1067, WE01M0316, WE03X37317-50PK, WE1M1067-100PK, WE1M316, WE1M481, WE1M507, AP7217723, PS17137203. This Kit Includes Following Parts WE14M124 top front bearing WE09X27634 front drum felt WE03X29897 drive belt 2 x WE1M504 bearing slides, 2 x WE1M1067 glide slides Description: The WE49X21874 Dryer Bearing Kit is designed for front-load dryers and makes servicing the dryer easy, affordable, and convenient. This kit works for select GE front-load dryer models. This is an aftermarket part that can be used as a replacement for the OEM part.

Read more less

WE49X20697 Dryer Genuine OEM Front Bearing Repair Kit This Kit Includes Following Parts WE3M26 top front bearing WE09X27634 front drum felt WE03X29897 drive belt 2 x WE03X37317 bearing slides, 2 x WE03X37318 glide slides Replaces Part Numbers:WE49X20697, AP5806906, PS9493092, WE03X37318, WE1M504, WE01M0333, WE1M333, AP7217724, WE03X37317, WE1M1067, WE01M0316, WE1M316, WE1M481, WE1M507, AP7217723, WE03X29897, WE12M29, WE12X21574, WE21M29, 559C197P001, 559C197P003, WE120122, WE12M0022, WE12M22, WE12M33, AP7012633, WE3M26,  1089201, AH960316, EA960316, PS960316, WE03M0020, WE3M20, AP3790641, WE09X27634, WE09X20441, WE9M30, WE09M0015, WE9M15, AP6889049.   California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

W11189144 Genuine OEM Dryer Felt Drum Seal - Compatible with Whirlpool, Maytag, Kenmore Product Description Maintain your dryer’s efficiency with the W11189144 Genuine OEM Dryer Felt Drum Seal. This Whirlpool-manufactured felt seal is designed as a replacement for select Whirlpool, Maytag, Kenmore, and other compatible dryers. It wraps around the drum, creating a protective barrier between the drum and the cabinet to prevent air leaks, lint buildup, and debris accumulation. This part addresses issues like excess lint near the door, dust inside the dryer, or longer drying times due to reduced airflow efficiency, often caused by wear from regular use or high-heat conditions. Note: Includes (1) felt drum seal. Disconnect power before installation. Verify compatibility with your dryer model. Replaces part numbers: W11189144, W10664120, 4547089, AP6286713, PS12348807, PD00049832, EAP12348807. Compatibility: Compatible with select dryer models, including but not limited to: Whirlpool: WED8500DC2, WED8500DC3, WED8500DC4, YWED8500DW0, YWED8500DW4 Maytag: MEDB835DW4, MEDB855DC4, MGDB835DW3, YMEDB855DW4 Kenmore: 110.68132410, 110.68132414, 110.69133410, 110.79133414 Amana: NED4655EW0 Verify your model number or contact our support team for assistance. Key Features: ✅ Brand and Models Compatibility: Fits select Whirlpool, Maytag, Kenmore, Amana, and other dryers. 🔧 Specifications: Genuine OEM Whirlpool felt drum seal, high-quality felt material. 💪 Reliable Performance: Prevents air leaks and lint buildup for efficient drying. 🛠️ Easy Installation: Requires adhesive and basic tools; typically installed in 30–60 minutes. 🛡️ Effective Fixes: Resolves excess lint buildup, dust accumulation, and longer drying times. Product Specification Part Number: W11189144 Component Type: Dryer felt drum seal Material: High-quality felt Additional Specs: Adhesive-backed for secure installation Compliance: Prop 65 warning for California Installation Notes: Safety First: Disconnect the dryer from the power source before installation. Shop for high-quality appliance parts with a 30-day return policy. Keep your dryer running efficiently today! Add to cart now for a reliable fix!

Read more less

EXP643 Dryer Belt & Idler Pulley Kit for LG  This Set is Combination of Dryer Drum Belt and Idler Pulley Roller. Parts Included in Kit:      Dryer Drum Belt Replaces Part Numbers: 4400EL2001F, 4400EL2001A, 4400EL2001C, 4400EL2001E, AP5972814, PS11705916. Dryer Idler Pulley Roller Replaces Part Numbers: 4560EL3001A, PS3523032, AP4438625   This is an aftermarket part that can be used as a replacement for the OEM part. California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less