Dishwasher Parts

W10518394 Genuine OEM Whirlpool Dishwasher Heating Element The W10518394 is a Genuine OEM Whirlpool replacement dishwasher heating element compatible with select Whirlpool, Maytag, KitchenAid, Amana, and Kenmore Whirlpool-built dishwashers — including the WDF, WDT, ADB, and related series. The heating element is mounted at the bottom of the dishwasher tub and serves two purposes: it heats the wash water to the temperature required by the selected cycle (improving cleaning performance and helping detergent dissolve and work effectively), and it provides drying heat at the end of the cycle to evaporate moisture from dishes during the heated dry phase. When the element fails, dishes come out wet, glassware is spotted or cloudy, and wash performance noticeably degrades. This is an oval-shape element rated 1200W, approximately 15"L x 3"W x 3"H. As a Genuine OEM part manufactured by Whirlpool to factory specifications, the W10518394 directly replaces W10518394VP, W10134009, W10441445, 8194250, 8563007, 8563464, 8572861, 2977737, 1381534, 8268559, A3-06, AP4325066, AP5690151, EAP9605070, PD00012075, PS1960583, and PS9605070. The element mounts to the bottom of the tub with large nuts on the underside — the rubber washer (Whirlpool 717273) and heater nut (Whirlpool 8268548) are sold separately if they need replacement. Important: after installation on most Whirlpool dishwashers, you must run the diagnostic mode to reset the control board to recognize the new element. Installs in 30–45 minutes with basic hand tools. Quick Answer The W10518394 Genuine OEM Whirlpool Dishwasher Heating Element fixes Whirlpool, Maytag, KitchenAid, Amana, and Kenmore dishwashers where dishes come out wet, glassware is spotted, wash water isn't getting hot, or the heated dry phase isn't working. Oval shape, 1200W, ~15"L x 3"W x 3"H. Genuine OEM. Replaces W10518394VP, W10134009, W10441445, 8194250, 8563007, 8563464, 8572861, 2977737, AP4325066, AP5690151, PS1960583, PS9605070. Diagnostic reset required on most Whirlpool dishwashers after installation. Rubber washer (717273) and heater nut (8268548) sold separately if needed. Common Problems This Part Fixes Dishes coming out wet at the end of the cycle — element not providing heat for the drying phase Wash water not getting hot enough — poor cleaning performance even with proper detergent Glassware coming out cloudy or spotted — water not reaching temperature for proper detergent activation Heated dry cycle not working — no warm air at the end of the cycle Element visibly burned through, broken, or showing arcing damage Multimeter continuity test on the element shows an open circuit (no continuity) Heating element showing the wrong region glowing red (only a 6" segment heating rather than the whole element) Detergent not fully dissolving — water too cool to activate the formulation Replaces Part Numbers This dishwasher heating element directly replaces the following OEM and cross-reference part numbers: W10518394, 2977737, 8194250, 8563007, 8572861, W10134009, W10441445, W10518394VP, AWP40983, PD00004893, EAP8260087, AP5690151, PS8260087. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Always confirm the shape and dimensions of your old element match this oval ~15" element before ordering — some Whirlpool dishwashers use a different horseshoe-style element instead. Compatibility This dishwasher heating element is compatible with select Whirlpool, Maytag, KitchenAid, Amana, and Kenmore dishwashers, including: Whirlpool dishwashers — WDF330PAHS, WDF520PADM, WDT720PADM, WDT730PAHZ series and related models Whirlpool dishwashers — additional WDF and WDT series models (verify with parts diagram) Maytag dishwashers — select models (verify with parts diagram) KitchenAid dishwashers — select models Amana dishwashers — ADB1400AGW and related models Kenmore / Sears dishwashers — select Whirlpool-built models Important — Confirm Element Shape Before Ordering: The W10518394 is an oval-shape heating element approximately 15" in length. Some Whirlpool-platform dishwashers use a different horseshoe-style heating element instead, which is NOT interchangeable with this one. Before ordering, visually compare your old element's shape and length to this part, or check your dishwasher's parts diagram to confirm W10518394 is the correct element for your specific model. If your element is horseshoe-shaped, you need a different part number — contact our support team with your model number. Key Features Genuine OEM part manufactured by Whirlpool to factory specifications — guaranteed fit and performance Heats wash water for optimal cleaning performance and provides drying heat during the heated dry phase Rated 1200W for efficient heating and reliable temperature control Oval-shape element approximately 15" L x 3" W x 3" H Mounts in the bottom of the dishwasher tub, secured underneath with large nuts Note: rubber washer (Whirlpool 717273) and heater nut (Whirlpool 8268548) sold separately if yours need replacement Diagnostic reset required on most Whirlpool dishwashers after installation (typically pressing any 3 buttons in sequence 3 times) Replaces 18+ OEM and cross-reference part numbers including W10518394VP, W10134009, W10441445, 8194250, 8563007, 8563464, 8572861, AP4325066, AP5690151, PS1960583, PS9605070 Compatible with Whirlpool WDF and WDT series, Maytag, KitchenAid, Amana ADB1400AGW, and Kenmore Whirlpool-built dishwashers DIY repair — installs in 30–45 minutes with basic hand tools Product Specifications Part Number W10518394 Part Type Dishwasher Heating Element Condition Genuine OEM Application Dishwashers (Whirlpool platform) Shape Oval (NOT interchangeable with horseshoe-style elements) Wattage 1200W Dimensions Approximately 15" L x 3" W x 3" H Mounting Location Bottom of dishwasher tub Related Parts (Sold Separately) Rubber Washer (717273), Heater Nut (8268548) Post-Install Step Diagnostic reset required on most Whirlpool dishwashers Compatible Brands Whirlpool, Maytag, KitchenAid, Amana, Kenmore Installation Notes ⚠️ Unplug Dishwasher and Shut Off Water Before Starting — Don't Touch Element with Bare Hands Disconnect power at the breaker and shut off the water supply at the valve under the sink before beginning. Wear work gloves and safety glasses to protect your hands and eyes. Handle the new heating element only by the metal end terminals or its support brackets — do NOT touch the heating coil itself with bare fingers; skin oils can cause hot spots that shorten element life. From inside the dishwasher tub, the element is visible at the bottom — it's the looped metal coil running along the floor of the tub. Remove the bottom rack and any debris to clear access. To access the wire connections and mounting nuts, you'll need to either reach underneath the dishwasher from the front access panel or, on some installations, pull the dishwasher out partially. From underneath: disconnect the two wires from the bottom of the element terminals (photograph the wire connections first to ensure correct reinstallation). Remove the plastic nuts holding the element terminals in place. From inside the tub, lift the old element straight up and out. Inspect the rubber washers — if they're cracked, hardened, or torn, replace them now with new 717273 washers. Install the new W10518394 element through the same mounting holes, replace the rubber washers if needed, and secure with the plastic nuts (or new 8268548 nuts) from underneath. Reconnect the two wires to the terminals matching your original orientation. Important: after restoring power, run the Whirlpool diagnostic mode to reset the control board — on most models this is done by pressing any three buttons in sequence three times and closing the door, which initiates a ~30-minute diagnostic cycle. The new element will not be recognized by the control until this is done. Tools needed: Phillips screwdriver, 5/8" wrench, 5/16" nut driver, 3/4" wrench, work gloves, safety glasses. Frequently Asked Questions Why are my dishes coming out wet — is the heating element the cause? Most likely, yes — wet dishes are the classic signature of a failed dishwasher heating element. The element provides heat for the dry phase, evaporating moisture from dish surfaces. When it fails, dishes simply air-dry, which leaves them wet (especially plastics and the interior of inverted glassware). To confirm: with the dishwasher unplugged, disconnect the wires from the element and check continuity with a multimeter. A working element shows continuity; a failed element shows an open circuit (infinite resistance). Also check that you have the heated dry option enabled in your cycle settings — some users mistakenly turn off heated dry and then assume the element has failed. After installing the new element, the dishwasher still isn't heating — why? On most Whirlpool dishwashers, you must run the diagnostic mode after replacing the heating element so the control board recognizes the new part. To enter diagnostic mode on most Whirlpool models, press any three buttons in sequence three times rapidly, then close the door — this starts a roughly 30-minute diagnostic cycle that resets the heater logic. If you've installed the new element correctly and it still isn't heating after the diagnostic cycle, also check the high-limit thermostat (a safety component that can stop power to the element if it has failed open). Confirm your wire connections are tight on the element terminals as well. How is the W10518394 different from horseshoe-shape heating elements? The W10518394 is an oval-shape element about 15" in length. Some Whirlpool-platform dishwashers — even similar-looking models — use a horseshoe-shape element instead, which has a different mounting hole pattern and shape that won't fit positions designed for the oval element. The two are NOT interchangeable. Before ordering, compare your old element to a photo of the W10518394, or check your dishwasher's parts diagram. If your old element is horseshoe-shaped, contact our support team with your model number and we'll help identify the correct horseshoe-style element for your dishwasher. Do I need to replace the rubber washers and nuts when installing this? Not always — they're reusable as long as they're in good condition. Inspect the rubber washers (Whirlpool 717273) for cracks, hardening, or tears. If they're brittle or torn, replace them now while you have the element out — they prevent water leaks from the tub at the element mounting points. The plastic heater nuts (Whirlpool 8268548) are usually reusable unless visibly damaged. Both parts are sold separately if you need replacements. Reusing torn rubber washers is the most common cause of leaks after this repair, so don't skip the inspection. Is this a Genuine OEM or aftermarket part? This is a Genuine OEM part manufactured by Whirlpool to factory specifications. It is the exact same heating element installed in compatible Whirlpool, Maytag, KitchenAid, Amana, and Kenmore Whirlpool-built dishwashers from the factory — guaranteed fit, materials, and performance. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO DD31-00016A Dishwasher Drain Pump Motor The XPARTCO DD31-00016A is an aftermarket replacement BLDC (brushless DC) drain pump motor for Samsung dishwashers. This motor removes water from the dishwasher tub during the drain phase of the cycle — an impeller mechanism pumps water out through the drain hose, running during the draining phase to ensure a constant, steady flow and help prevent clogs. Weighs approximately 0.50 lbs, with package dimensions of 4.02" x 3.50" x 3.54". Compatible with 120V and 230V systems. Common causes of failure include worn motor bearings, electrical failure, or debris obstructing the impeller. Symptoms of a failing drain pump motor include water not draining from the tub, standing water left after a cycle, unusual noise during the drain phase, or intermittent draining problems that don't happen every cycle. It directly replaces AP5917178, 113121, 4000925, EAP9606350, PS9606350, ASM773863, PD00036475, and 045900194701. Quick Answer The XPARTCO DD31-00016A Dishwasher Drain Pump Motor fixes Samsung dishwashers that aren't draining, leave standing water after a cycle, make unusual noise during draining, or have intermittent draining problems. BLDC motor, 120V/230V, ~0.50 lbs. Replaces AP5917178, 113121, 4000925, EAP9606350, PS9606350, ASM773863, PD00036475, 045900194701. When removing the old motor, you'll need to hold a release tab open while twisting the motor counterclockwise at the same time — this two-handed step trips up a lot of first-time installers. Common Problems This Part Fixes Dishwasher not draining water from the tub Standing water left in the tub after a completed cycle Unusual noise during the drain phase Intermittent draining problems that don't occur every cycle Reduced water circulation and cleaning performance Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dishwasher drain pump motor directly replaces the following OEM and cross-reference part numbers: DD31-00016A, 113121, 4000925, AP5917178, ASM773863, EAP9606350, PD00036475, PS9606350 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This drain pump motor is compatible with select Samsung dishwashers, including model numbers such as DW80R9950QH/AA, DW80B7070UG/AA, DW80R9950MT/AA, DW80B6061UG/AA, DW80R9950QN/AA, DW80B7070US/AA, DW80B6061US/AA, DW80B7071UG/AA, DW80B6060US/AA, DW80B6060UG/AA, DW80BB7070U1/AA, DW80B7070AP/AA, DW80B7071US/AA, DW80R7061UG/AA, DDW24T999BB/DA, DDW24M999UM/DA, DDW24T998US/DA, DDW24M999US/DA, DW60M9990AP, and DW80B6060UG. Note: This part is not a replacement for any earlier designation — per Samsung's own listing, DD31-00016A is a new part that doesn't supersede another part number. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Aftermarket replacement BLDC (brushless DC) drain pump motor Resolves "won't drain," "standing water," "unusual noise," and "intermittent draining" symptoms Impeller mechanism pumps water out through the drain hose to prevent clogs Compatible with 120V and 230V systems Direct drop-in replacement matching the original mounting and connections Replaces AP5917178, 113121, 4000925, EAP9606350, PS9606350, ASM773863, PD00036475, and 045900194701 Compatible with Samsung dishwashers Aftermarket replacement built to OEM-equivalent quality standards Typical repair takes 30 to 60 minutes Product Specifications Part Number XPDD31-00016A OEM Part Number DD31-00016A Part Type Dishwasher Drain Pump Motor (BLDC) Condition Aftermarket Replacement Brand Samsung Motor Type Brushless DC (BLDC) Voltage Compatibility 120V / 230V Weight Approx. 0.50 lbs Package Dimensions 4.02" x 3.50" x 3.54" Repair Difficulty Moderate — 30 to 60 minutes Quantity 1 drain pump motor Compatible Brand Samsung Installation Notes ⚠️ Unplug Dishwasher And Shut Off Water Supply Before Starting — This Step Needs Two Hands Turn off and unplug the dishwasher for safety, and shut off the water supply before beginning. Wear work gloves. Remove any panels or components blocking access to the motor pump. Disconnect all wiring from the old motor. Removing the old motor requires holding a release tab open while simultaneously twisting the motor counterclockwise — this two-handed step trips up a lot of first-time installers, so take it slowly and make sure the tab stays held open through the full twist. Once free, remove the old motor. Install the new DD31-00016A securely in the same mounting position. Reconnect all wiring according to the original connections. Reinstall any panels or components removed for access. Restore the water supply and power, then run a test cycle to confirm the dishwasher drains completely with no leaks or unusual noise. Tools needed: screwdriver, work gloves. Frequently Asked Questions My dishwasher isn't draining. Is this the part I need? Yes, this is the most direct symptom of a failed drain pump motor. Since this motor is what removes water from the tub during the drain phase, a worn or failed motor can leave standing water behind or prevent the cycle from completing properly. My dishwasher's drainage problem only happens sometimes. Could this still be the motor? Yes, this is possible. One customer replaced this exact motor to address an intermittent draining issue, noting it was somewhat of a guess since the problem didn't occur every cycle. Intermittent symptoms can still point to a motor that's beginning to fail rather than one that's failed completely, though it's worth noting the customer wasn't fully certain the replacement resolved their specific issue. What's the trickiest part of installing this motor? Removing the old motor requires holding a release tab open while twisting the motor counterclockwise at the same time — a two-handed maneuver that one customer specifically called out as the biggest challenge of the whole repair. Taking it slowly and keeping steady pressure on the tab through the full twist makes this easier. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Samsung OEM part, but is manufactured to match the motor design, impeller mechanism, and voltage compatibility of the original DD31-00016A drain pump motor used in compatible Samsung dishwashers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO W10195416 Dishwasher Lower Rack Wheel Replaces W10195416V The XPARTCO W10195416 is an aftermarket replacement lower dishrack wheel assembly for Whirlpool dishwashers, and also fits select Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models. This assembly attaches directly to the lower dishrack and lets it slide in and out of the dishwasher smoothly during loading and unloading. This is a current, superseding part number — it replaces the earlier W10195416V designation. Finished in gray, made of heat-resistant ABS plastic without BPA, rated for temperatures up to 300°F. The wheel measures approximately 1.59" in diameter, with an overall assembly height of about 2.83" and a footprint of roughly 3" x 6". Over time, normal wear and tear can crack or break the wheel or its mounting caps. Symptoms of a failing wheel assembly include the rack becoming difficult to slide, jerky or uneven wheel movement, noisy or screeching sounds when moving the rack, or in more advanced cases, dishes not cleaning properly because the rack isn't positioned correctly. It directly replaces W10195416V, W10195416, W10195416VP, 1872127, 4245021, AP5983730, AWP1252597, EAP11722152, PD00024134, PS11722152 Quick Answer The XPARTCO W10195416 Dishwasher Lower Rack Wheel fixes Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore dishwashers where the lower rack is hard to slide, moves jerkily, makes noise, or won't clean dishes properly because it's out of position. Gray, ABS plastic, ~1.59" wheel diameter. Replaces W10195416V, W10195416, W10195416VP, 1872127, 4245021, AP5983730, AWP1252597, EAP11722152, PD00024134, PS11722152. This wheel snaps on and off — no tools are typically required for installation. Common Problems This Part Fixes Lower rack difficult to slide in or out Jerky or uneven wheel movement Noisy or screeching sound when moving the rack Dishes not cleaning properly due to a misaligned rack Broken or cracked wheel visible on the rack Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dishwasher lower rack wheel directly replaces the following OEM and cross-reference part numbers: W10195416V, W10195416, W10195416VP, 1872127, 4245021, AP5983730, AWP1252597, EAP11722152, PD00024134, PS11722152 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This lower rack wheel is compatible with select Whirlpool dishwashers, and also fits select Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore dishwashers built on the Whirlpool platform, including model numbers such as WDT780SAEM1, MDB4949SDM2, and Kenmore 66513222N410, 66513222N411, 66513222N412, 66513222N413, 66513223N410, 66513223N411, 66513293K116, and 66513299K110. Note: This wheel is a different part from the similarly-numbered W10195417 and W10195420 wheels used on other models. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure which wheel your dishwasher needs. Key Features Aftermarket replacement wheel assembly — factory-equivalent wheel and mount design Lets the lower dishrack slide in and out of the dishwasher smoothly Resolves "rack hard to slide," "jerky movement," "noisy operation," and "dishes not cleaning properly" symptoms Superseding part number — current replacement for the earlier W10195416V designation Gray, heat-resistant ABS plastic without BPA, rated up to 300°F Approximately 1.59" wheel diameter, 2.83" assembly height, ~3" x 6" footprint Snap-on/snap-off installation — no tools typically required Replaces W10195416V, W10195416, W10195416VP, 1872127, 4245021, AP5983730, AWP1252597, EAP11722152, PD00024134, PS11722152 Compatible with Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore dishwashers Aftermarket replacement built to OEM-equivalent quality standards Product Specifications Part Number W10195416 OEM Part Number W10195416V Part Type Dishwasher Lower Rack Wheel Assembly Condition Aftermarket Replacement Brand Whirlpool Color Gray Material ABS plastic (BPA-free) Heat Resistance Up to 300°F Wheel Diameter Approx. 1.59" Assembly Height Approx. 2.83" Overall Footprint Approx. 3" x 6" Supersedes W10195416V Repair Difficulty Very Easy — snap-on, no tools required Quantity 1 wheel assembly Compatible Brands Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, Kenmore Installation Notes ⚠️ Unplug Dishwasher Before Starting Disconnect power to the dishwasher before beginning. Open the dishwasher door and pull out the lower dishrack fully. Locate the old wheel assembly and push the tab from both sides — it should pop out of the rack. Take the new W10195416 wheel assembly and position it on the rack, making sure the caps overlap the wire from the inside before clipping it into place by pushing on the wheel until it snaps securely. Repeat for any other worn wheels on the rack. Slide the rack back into the dishwasher and test it by pulling it in and out to confirm smooth, quiet movement. Tools needed: none typically required. Frequently Asked Questions My dishwasher rack is hard to slide. Is this the part I need? Yes, this is the most common symptom of a worn or broken lower rack wheel. Since this wheel is what lets the rack roll smoothly in and out of the dishwasher, a cracked or damaged wheel can make the rack feel stiff, jerky, or difficult to move. Is this a difficult repair? No, this is one of the simplest dishwasher repairs. One customer described it as "an easy fix" — the old wheel snaps off, and the new one snaps right on, typically without needing any tools. My old part number is W10195416V. Is this the same thing? Yes, W10195416 is the current part number and supersedes the earlier W10195416V designation. If your old wheel's number matches either of these, this is the correct current part to order. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured to match the wheel design, mounting caps, and dimensions of the original W10195416V lower rack wheel used in compatible Whirlpool, Maytag, KitchenAid, and related dishwashers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO DD62-00084A Dishwasher Water Valve – Compatible with Samsung Dishwashers Product Description Restore proper water flow and reliable cleaning performance with the XPARTCO DD62-00084A Dishwasher Water Valve. This Dishwasher Water Valve is an essential component for maintaining the optimal performance of your dishwasher. This replacement part ensures precise water flow control, allowing your dishwasher to operate efficiently and effectively. A faulty water valve can cause no water entering the dishwasher, slow filling, or poor cleaning performance. Replacing it with this dependable XPARTCO valve helps restore consistent water flow and efficient operation. XPARTCO provides cost-effective aftermarket appliance parts engineered to match original fit and function. Replaces Part Numbers DD62-00084A, 2692215, ASM36078, EAP4222448, PD00002158, 737534554937, OEM15534663, AP5178218, PS4222448 Compatibility This replacement dishwasher water inlet valve fits select Samsung dishwashers. Common compatible models include (but are not limited to): Samsung DW80F600UTS Samsung DW80J3020US Always verify your dishwasher’s model number before ordering.Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement – Matches OEM fit and water flow performance 💧 Accurate Water Fill Control – Ensures proper water levels for effective cleaning ⚙️ Fixes Common Issues – Resolves no-fill or slow-fill problems 💪 Durable Solenoid Valve – Designed for reliable long-term use 💰 Cost-Effective Repair – Affordable alternative to OEM valves ⚠️ Symptoms If your dishwasher is experiencing any of the following issues, this part may need replacement: ❌ Dishwasher not filling with water 💧 Slow or weak water flow ⚠️ Poor cleaning performance due to low water level 🔄 Cycle not starting properly 🚫 No water entering during wash cycle Replacing this water valve can restore proper dishwasher operation and cleaning efficiency. 📐 Product Specification Part Number: XPDD62-00084A Component Type: Dishwasher Water Inlet Valve Voltage: 120V AC Application: Dishwasher water supply system Mounting: Screw-mounted with hose connection Quality Level: Aftermarket replacement (not OEM) 🛠️ Installation Notes Tools Needed: Phillips screwdriver, adjustable wrench ⚠️ Safety First: Disconnect power and shut off the water supply before servicing the dishwasher. Basic Steps: Turn off power and water supply. Remove the lower access panel. Disconnect water supply line and electrical connector. Remove mounting screws and remove the old valve. Install the new XPARTCO DD62-00084A valve. Reconnect water line and wiring. Restore power and water, then test for leaks and proper filling. ⏱️ Time Required: 20–30 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Aftermarket Appliance Parts 🔄 30-Day Return Policy Restore reliable dishwasher performance — Add to Cart Now for a dependable repair!

Read more less

2 Pack - XPARTCO 4933DD3001B Dishwasher Door Hinge Cable – Compatible with LG & Kenmore Dishwashers Product Description Restore smooth and controlled dishwasher door movement with the XPARTCO 4933DD3001B Dishwasher Door Hinge Cable. This high-quality aftermarket replacement connects the dishwasher door to the hinge spring system, allowing the door to open and close evenly without slamming or dropping. A worn or broken hinge cable can cause the door to fall open, feel too heavy, or fail to stay balanced. Replacing it with this durable XPARTCO cable helps restore proper door tension and safe operation. XPARTCO is a trusted aftermarket brand offering appliance replacement parts designed to meet OEM-equivalent specifications at a cost-effective price. Replaces Part Numbers 4933DD3001B, 1395107, 4933DD3001A, PD00001803, EAP3524406, AH3524406, AP4511304, EA3524406, PS3524406   Compatibility This replacement dishwasher door hinge cable fits select LG and Kenmore (LG-manufactured) dishwashers. Example compatible models include (but are not limited to):LG LDF7811ST, LDF6920STKenmore 795.13293K701, 795.13299K701 Always verify your dishwasher’s model number before ordering.Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement – Matches OEM fit, length, and tension performance 🚪 Restores Proper Door Balance – Prevents door from dropping or slamming 💪 Durable Steel Cable – Designed to withstand repeated door cycles 💰 Cost-Effective Repair – Reliable alternative to OEM hinge cables 🛡️ Fixes Common Issues – Solves loose door, uneven opening, or excessive door weight 📐 Product Specification Part Number: 4933DD3001B Component Type: Dishwasher Door Hinge Cable Material: Braided steel cable with end fittings Application: Door hinge and spring tension system Installation Side: Typically used on left or right side (model dependent) Quality Level: Aftermarket replacement (not OEM) 🛠️ Installation Notes Tools Needed: Phillips screwdriver, needle-nose pliers ⚠️ Safety First: Disconnect power to the dishwasher before servicing. Door springs are under tension—use caution during installation. Basic Steps: Disconnect dishwasher power. Remove the lower access panel. Carefully release tension from the old hinge cable. Remove the damaged cable from the hinge and spring. Install the new XPARTCO 4933DD3001B cable in the same routing. Reattach spring tension and reinstall access panel. Test door movement for smooth, balanced operation. ⏱️ Time Required: 20–30 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Aftermarket Appliance Parts 🔄 30-Day Return Policy Restore smooth, controlled dishwasher door operation — Add to Cart Now for a dependable, budget-friendly repair!

Read more less

W11175771 Genuine OEM Whirlpool Dishwasher Water Valve The W11175771 is a genuine Whirlpool OEM water inlet valve for Whirlpool, Kenmore, KitchenAid, Amana, Crosley, Magic Chef, and Inglis dishwashers, located behind the lower kick plate panel in either the right or left corner. This valve controls the flow of water into the appliance during the wash cycle — an electrical solenoid plunger opens and closes the valve to admit exactly the right amount of water at the appropriate stages of the dishwasher's cycle. Measuring approximately 3.37" in height, this is a superseding part, replacing the earlier W10872255 and W11130744 valve numbers so older models can be updated with the current version. Over time, a screen inside the valve can become clogged with sediment — this screen isn't designed to be cleaned or serviced, so a clog means the whole valve needs to be replaced. A failing valve produces a clear set of symptoms: the dishwasher not filling with enough water or not filling at all, leaking into the dishwasher while not in use, or overfilling with too much water. It directly replaces AP6339872, W10195047, W10327250, W10872255, W11130744, W10327249, W10316814, and W11130743. Quick Answer The W11175771 Genuine OEM Whirlpool Dishwasher Water Valve fixes Whirlpool, Kenmore, KitchenAid, Amana, Crosley, Magic Chef, and Inglis dishwashers that aren't filling with water, are leaking, or are overfilling. Located behind the lower kick plate panel. Replaces AP6339872, W10195047, W10327250, W10872255, W11130744, W10327249, W10316814, W11130743. While the dishwasher is disassembled for this repair, consider also checking or replacing the water supply adapter, since it's in the same area and easy to inspect at the same time. Common Problems This Part Fixes Dishwasher not filling with enough water, or not filling at all Water leaking into the dishwasher while it's not in use Dishwasher overfilling with too much water High-pitched whining sound while the dishwasher is filling Poor washing results or an error code related to water fill Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dishwasher water inlet valve directly replaces the following OEM and cross-reference part numbers: W11175771, 3015468, 328C151-T, 4451572, 4843711, AP5804368, AP6024301, AP6339872, EAP11738107, EAP12578165, EAP3406951, AWP43823, PD00052484, PS11738107, PS12578165 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This water inlet valve is compatible with select Whirlpool dishwashers, and also fits select Kenmore, KitchenAid, Amana, Crosley, Magic Chef, and Inglis dishwashers built on the Whirlpool platform, including model numbers such as WDF130PAHB1, WDF130PAHB2, WDF130PAHS1, WDF130PAHS2, WDF130PAHW2, WDF330PAHB3, WDF330PAHW4, WDF331PAHB1, WDF520PADB9, WDF520PADM, WDT730PAHZ, WDT720PADM, WDF330PAHS, ADB1400AGW, KDTE104ESS1, and Kenmore 66513222N410 through N414. Note: Always verify your full model number before ordering, since similar-looking dishwasher water valves can vary between models. Contact our support team with your model number if you're unsure. Key Features Genuine Whirlpool OEM part — factory-specified solenoid design and flow rate Regulates water flow into the dishwasher via an electrical solenoid plunger Resolves "won't fill," "leaking," "overfilling," and "whining noise" symptoms caused by valve failure Superseding part — current replacement for the earlier W10872255 and W11130744 valves Approximately 3.37" in height Direct drop-in replacement — matches the original mounting and hose connections Replaces AP6339872, W10195047, W10327250, W10872255, W11130744, W10327249, W10316814, and W11130743 Compatible with Whirlpool, Kenmore, KitchenAid, Amana, Crosley, Magic Chef, and Inglis dishwashers Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number W11175771 Part Type Dishwasher Water Inlet Valve Condition Genuine OEM Brand Whirlpool Location Behind the lower kick plate panel, right or left corner Height 3.37" Supersedes W10872255, W11130744 Screen Serviceable No — replace valve if clogged Repair Difficulty Easy to Moderate — approx. 15 to 30 minutes Quantity 1 valve Compatible Brands Whirlpool, Kenmore, KitchenAid, Amana, Crosley, Magic Chef, Inglis Installation Notes ⚠️ Unplug Dishwasher And Shut Off Water Supply Before Starting Disconnect power at the outlet or shut off the circuit breaker, and shut off the water supply before beginning. Wear work gloves. Remove the bottom front kick plate to access the interior, where the valve is located behind the panel in either the right or left corner depending on your model. Photograph the wiring and hose connections before disconnecting anything. Disconnect the water line, the electrical connector, and remove the mounting screws securing the old valve, then pull it free. Install the new W11175771 in the same position, securely reconnect the water line and electrical connector, and secure the mounting screws. While you're in this area, it's worth inspecting the water supply adapter for wear, since it's a related part in the same location that's easy to check while everything is already accessible. Reinstall the kick plate, restore the water supply and power, then run a test cycle to confirm the dishwasher fills correctly with no leaks. Tools needed: Phillips screwdriver, pliers, work gloves. Frequently Asked Questions My dishwasher isn't filling with water at all. Is this the right part? Yes, this is the most direct symptom of a failed water inlet valve. Since this valve is what admits water from your household supply into the dishwasher, a solenoid failure or internal blockage can prevent any water from entering at all, stopping the wash cycle from proceeding. Can I just clean the valve's screen instead of replacing the whole thing? No — the screen inside this valve isn't designed to be cleaned or serviced. If it becomes clogged with sediment from your household water supply, the entire valve should be replaced rather than attempting to clean or repair the screen itself. My dishwasher makes a high-pitched whining sound while filling. Is that this valve? Yes, this is a documented symptom of a failing water inlet valve. One customer specifically traced an "obnoxious high-pitched whining sound when filling with water" to this exact valve and resolved it with a straightforward replacement in about 15 minutes. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by Whirlpool to factory specifications — guaranteed fit, materials, and performance. It matches the original solenoid design, flow rate, and connection type of the water inlet valve originally installed in your dishwasher. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

WD21X25468 Genuine OEM GE Dishwasher Pressure Sensor Assembly The WD21X25468 is a Genuine OEM GE replacement dishwasher pressure sensor assembly compatible with a wide range of GE, GE Profile, GE Café, Hotpoint, Haier, and Monogram dishwashers in the GDF, GDT, GDP, PDT, CDT, ZDT, QDP, and HDF series. The pressure sensor monitors water pressure inside the dishwasher tub during fill and drain cycles and sends real-time readings to the electronic control board. The control board uses these readings to calculate the correct amount of water needed for each wash cycle and to confirm that the tub has drained properly before advancing to the next cycle phase. When the pressure sensor fails — or when it becomes clogged with grease, food residue, or mineral buildup — the dishwasher may not fill with water, may overfill, may stop mid-cycle, may fail to drain correctly, or may display error codes H2O or FTD (Failure to Drain). This Genuine OEM part is manufactured by GE to factory specifications. It directly replaces AP6976524, PS12741258, EAP12741258, 4962334, 37640602, and 265D3356P001. Sold individually. Installs in 15–20 minutes — a screwdriver is the only tool required for most models. Quick Answer The WD21X25468 Genuine OEM GE Dishwasher Pressure Sensor Assembly fixes GE dishwashers displaying error codes H2O or FTD (Failure to Drain), not filling with water, overfilling, stopping mid-cycle, or running excessive noise from the spray arms. Monitors water level and pressure — signals the control board to fill, wash, and drain correctly. Genuine OEM. Replaces AP6976524, PS12741258, EAP12741258, 4962334, 37640602, 265D3356P001. Sold individually. Compatible with GE GDF, GDT, PDT, CDT, ZDT, QDP, HDF, and related series. Common Problems This Part Fixes Error code H2O displayed — dishwasher not receiving enough water or no water at all Error code FTD (Failure to Drain) displayed — sensor not confirming tub has drained Dishwasher not filling with water when a cycle is started Dishwasher overfilling — sensor not signaling the control board to stop filling Dishwasher stopping mid-cycle without completing the wash Excessive noise during operation — sensor not accurately controlling spray arm water pressure Dishwasher requires priming with water to start (filling the tub manually before it will run) Replaces Part Numbers This pressure sensor directly replaces the following OEM and cross-reference part numbers: WD21X25468, 265D3356P001, AGE24772, AP6976524, EAP12741258, OEM20929581, PD00067609, PS12741258. Contact our support team with your model number if you need confirmation before ordering. Compatibility This pressure sensor is compatible with a wide range of dishwashers from the following GE product lines: GE dishwashers — GDF450, GDF510, GDF511, GDF535, GDF550, GDF565, GDF570, GDF630, GDF640, GDF645 series GE dishwashers — GDT530, GDT535, GDT565, GDT580, GDT605, GDT625, GDT630, GDT635, GDT645, GDT695 series GE dishwashers — GDP615, GDP645, GDP665 series GE Profile dishwashers — PDT715, PDT775, PDT785 series GE Café dishwashers — CDT800, CDT875 series GE Monogram dishwashers — ZDT800, ZDT870, ZDT925, ZDT985 series Hotpoint dishwashers — HDF310, HDF330 series Haier dishwashers (select GE-platform models) GE / Café / Profile — QDP555 series Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Genuine OEM part manufactured by GE to factory specifications — guaranteed fit and performance Monitors water pressure inside the tub throughout fill and drain cycles — signals the control board to fill to the correct level and confirm complete drainage Resolves H2O and FTD error codes on compatible GE dishwashers Sensor can also fail due to grease or mineral buildup blocking the pressure port — cleaning may resolve the issue without replacement Replaces AP6976524, PS12741258, EAP12741258, 4962334, 37640602, and 265D3356P001 Compatible with GE GDF, GDT, GDP, PDT, CDT, ZDT, QDP, HDF, and Hotpoint dishwasher series Sold individually Quick DIY repair — installs in 15–20 minutes with a screwdriver Product Specifications Part Number WD21X25468 Part Type Dishwasher Pressure Sensor Assembly (Pressure Switch) Condition Genuine OEM Application GE, GE Profile, GE Café, GE Monogram, Hotpoint, Haier Dishwashers Function Monitors tub water level and pressure — signals control board for fill and drain control Error Codes Resolved H2O (no/low water), FTD (Failure to Drain) Sold As Single sensor assembly Compatible Brands GE, GE Profile, GE Café, GE Monogram, Hotpoint, Haier Installation Notes ⚠️ Unplug Dishwasher and Shut Off Water Before Starting Disconnect power and shut off the water supply before beginning. On most compatible GE models, the pressure sensor is located near the bottom of the dishwasher tub, accessible after removing the lower front kick panel (secured by one or two screws). The sensor assembly connects to a small hose and a wiring harness connector. Tip: before replacing the sensor, remove it and inspect the pressure port and hose for grease, food residue, or mineral buildup — a clogged sensor port can cause H2O and FTD errors without the sensor itself being electrically failed. Clean the port and hose with warm water and a small brush, reinstall, and test the dishwasher. If the error codes persist after cleaning, replace the WD21X25468 sensor. To replace: disconnect the hose and wiring harness from the old sensor, unclip or unscrew the sensor from its mounting bracket, and install the new sensor in the same position. Reconnect the hose and harness, restore power and water, and run a test cycle. Tools needed: Phillips screwdriver. Frequently Asked Questions What does the dishwasher pressure sensor do? The pressure sensor monitors the water pressure — and therefore the water level — inside the dishwasher tub throughout the wash cycle. It sends continuous readings to the electronic control board, which uses the data to determine how much water to add during fill, when to stop filling, and whether the tub has drained completely before advancing to the next cycle phase. An accurate pressure sensor is essential for the dishwasher to fill to the correct level (not too much, not too little), wash with the correct spray arm pressure, and drain fully before moving on to rinse or dry cycles. What do error codes H2O and FTD mean on GE dishwashers? H2O error code on compatible GE dishwashers indicates that the dishwasher is not detecting enough water in the tub — either water is not filling at all, or the pressure sensor is not sensing the water that has filled. FTD (Failure to Drain) code indicates the dishwasher has not confirmed that the tub has drained within the expected time. Both codes can be caused by a faulty pressure sensor, a clogged sensor port, a failed fill valve, a blocked drain system, or control board issues. The pressure sensor should be inspected and tested first since it is the most accessible and commonly replaced component for these two error codes. Should I try cleaning the sensor before replacing it? Yes — absolutely. The pressure sensor on GE dishwashers can produce H2O and FTD error codes when its pressure port or connected hose becomes clogged with grease, food residue, or hard water mineral deposits — even if the sensor itself is electrically intact. Before ordering a replacement, remove the sensor, inspect the pressure port opening, and clean it thoroughly with warm water and a small brush. Flush the connected hose to clear any buildup. Reinstall and run a test cycle. If the error codes return, the sensor has electrically failed and needs replacement with the WD21X25468. My dishwasher won't fill unless I pour water in manually first — is this the pressure sensor? Yes — this is a classic symptom of a clogged or failed pressure sensor. When the sensor port is blocked, the sensor reads zero pressure (empty tub) even when the dishwasher starts. In some cases the control board interprets this as a drainage confirmation and will not initiate the fill cycle. Pouring water into the filter manually raises the physical water level enough to trigger filling. Check and clean the sensor port as described above. If cleaning does not resolve the issue, replace the WD21X25468 sensor. Is this a Genuine OEM or aftermarket part? This is a Genuine OEM part manufactured by GE to factory specifications. It is the exact same pressure sensor assembly installed in compatible GE, GE Profile, GE Café, Hotpoint, and related brand dishwashers from the factory — guaranteed fit, materials, and performance. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less