WP3347288 Washer Lower Agitator  Fits Specific Top Load Washer Models. Replaces Part Number: WP3347288, 3347288, 3348245, 3352107, 519233, AP6008022, PS11741151. Description: The Lower Agitator is an OEM part designed for select Kenmore, Whirlpool top-loading washing machines. It sits at the bottom of the wash tub and plays a key agitation role during cycles. This is the bottom part of the agitator assembly.

Read more less

WH22X38697 Washer Genuine Control Board Fits Specific GE Washer Model Main Control Board Fl Washer Le W/instructions Replaces Part Numbers: WH22X38697, WH22X37837, WH22X36638, WH22X32458, WH22X35518, WH22X30897, WH22X29546, WH22X32058, WH22X34660, WH22X36858, WH22X37838, AP8054699, PS17874598.

Read more less

3360629 Washer Transmission Gearcase Description: The Transmission is an OEM part for Whirlpool washing machines. This integral component is at the heart of the washing machine's operation, translating the motor's power into action by driving the agitator and spinning the drum. Regular inspection and maintenance can prolong the life of the transmission, but if these symptoms occur, it may be time to replace this critical component.  Replaces Part Number: 3360629, W10140307, 285362, 62621, 8546456, W10172898, WP62621, WP8546456, 285194, 285291, 285312, 285392, 285515, 3349296, 3360263, 3360629R, 3360630, 388763, 389229, 389230, 389244, 389246, 3946631, 3947637, 3949609, 423, 62528, 62531, 62534, 62570, 62668, 62680, 63025, 63167, 63320, 63563, 63910, 63999, 8532118, 99890390, 99890391, AH341974, EA341974, AP3096209, PS341974, W10140301, W10140304, W10155438, W10251783, W10251785.   

Read more less

XPARTCO 8572717 Washer Motor Start Capacitor The XPARTCO 8572717 is an aftermarket replacement motor start capacitor for Whirlpool-built top-load washers and washer/dryer combination units. Unlike a run capacitor that stays in the circuit continuously, this start capacitor's job is brief and intense: at the instant the motor is commanded to start, it delivers a strong momentary boost of voltage to help the motor overcome its own inertia and get up to speed quickly. Once the motor reaches running speed, a relay switches it out of the circuit, handing off to the run capacitor for continuous operation. That short, high-stress duty cycle is exactly why start capacitors are a common failure point — they work hard for a fraction of a second on every single cycle start. Rated 189–227 MFD at 125VAC, 60Hz. The capacitor is a black cylindrical component mounted to the rear panel of the washer, held in place by a small plastic retaining clip and wrapped in a foam shield that protects it from moisture. Common failure modes include the internal dielectric breaking down from repeated startup stress, and in some cases the capacitor overheating badly enough to produce visible smoke if it fails while still energized. A failing start capacitor produces a clear symptom: the washer motor hums but won't start, or the motor fails to spin up while other functions of the washer still respond normally. It directly replaces 357021, 3949169, 661606, W10161696, W10244889, AP6013434, AH11746660, EA11746660, EAP11746660, PS11746660, AWP49120, and PD00003006. Quick Answer The XPARTCO 8572717 Washer Motor Start Capacitor fixes Whirlpool-built top-load washers and washer/dryer combos where the motor hums but won't start, the washer won't agitate or spin, or there's a burning smell from the motor area. Includes foam shield. 189–227 MFD, 125VAC, 60Hz. Replaces 357021, 3949169, 661606, W10161696, W10244889, AP6013434, AH11746660, EA11746660, EAP11746660, PS11746660, AWP49120, PD00003006. Capacitors store a dangerous electrical charge even after power is disconnected — always discharge before handling. Common Problems This Part Fixes Washer motor hums but won't start Washer won't agitate Washer won't spin or drain because the motor never starts Burning smell coming from the motor area Washer that starts a cycle but the drum never begins moving Motor that struggles to start under load but may start when the drum is empty Visible discoloration, bulging, or a burnt smell from the capacitor itself Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer motor start capacitor directly replaces the following OEM and cross-reference part numbers: 8572717, WP8572717, 357021, 3949169, 661606, W10161696, W10244889, AP6013434, AH11746660, EA11746660, EAP11746660, PS11746660, AWP49120, PD00003006 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This motor start capacitor is compatible with select Whirlpool-built top-load washers and washer/dryer combination units across the Whirlpool family of brands, including: Whirlpool top-load washers and washer/dryer combos — WET, WGT series Kenmore top-load washers (select Whirlpool-built 110-series models) Maytag, KitchenAid, Jenn-Air, and Amana washers (select models) Roper, Admiral, Hardwick, and Estate washers (select models) Magic Chef, Crosley, Inglis, Norge, Modern Maid, and Caloric washers (select models) Select Ikea washers built on the Whirlpool platform Verified model numbers include: WET4027EW, WET4024EW, LTE5243DQ, WET3300XQ, WGT3300XQ, MTW5670TQ0, SAWS800JQ1, LSN7233BW1, LSR7233DZ1, LSQ8243HQ0, LSQ8512KQ0, LSQ8543JQ0, LSQ8543JQ1, LSQ8543JT0, LSQ8543JT1, LSQ9244EQ0, LSQ9544KQ0, LSQ9549LG0, LSQ9549LG1, LSQ9549LG2, LSQ9549LG3, LSQ9549PW2, 8LSC6244BQ0, and Kenmore 110.72407600, 110.72408440, 110.74414130, 110.81360430, 110.82074620, 110.82984100, 110.91565810, and 110.98573110. Note: This capacitor fits both standalone washers and Whirlpool washer/dryer combination units. Always verify your full model number before ordering, since specifications and mounting can vary by platform. Contact our support team with your model number if you're unsure. Key Features Aftermarket replacement start capacitor — delivers a momentary voltage boost to get the washer motor spinning at startup Resolves "motor hums but won't start," "won't agitate," "won't spin," and "burning smell" symptoms caused by capacitor failure Rated 189–227 MFD, 125VAC, 60Hz Includes foam shield to protect against moisture — transfer or reuse per your model's original configuration Direct drop-in replacement — mounts to the same rear panel retaining clip Replaces 357021, 3949169, 661606, W10161696, W10244889, AP6013434, AH11746660, EA11746660, EAP11746660, PS11746660, AWP49120, and PD00003006 Compatible with Whirlpool, Kenmore, Maytag, KitchenAid, Jenn-Air, Amana, Roper, and related top-load washers and washer/dryer combos Aftermarket replacement built to OEM-equivalent quality standards Product Specifications Part Number 8572717 OEM Part Number WP8572717 Part Type Washer Motor Start Capacitor Condition Aftermarket Replacement Application Top-Load Washers / Washer-Dryer Combos (Whirlpool-Built) Capacitance 189–227 MFD (µF) Voltage 125VAC Frequency 60 Hz Shape Cylindrical (black) Included Components Foam moisture shield Mounting Rear panel, plastic retaining clip Quantity 1 start capacitor Compatible Brands Whirlpool, Kenmore, Maytag, KitchenAid, Jenn-Air, Amana, Roper, Admiral, Hardwick, Estate, Magic Chef, Crosley, Inglis, Norge, Modern Maid, Caloric, Ikea Installation Notes ⚠️ Danger — Capacitors Store A Dangerous Electrical Charge Unplug the washer or shut off the house circuit breaker before beginning. A capacitor stores an electrical charge even after power has been disconnected, and that charge can deliver a serious or fatal shock. Before touching either terminal, discharge the capacitor by shorting its two terminals together using an insulated-handle screwdriver, or by using a proper capacitor discharge tool with a resistor. Never short the terminals with a bare metal tool held with your bare hand. If you are not fully comfortable performing a capacitor discharge safely, have a qualified appliance technician replace this part instead. ⚠️ Transfer The Foam Shield To The New Capacitor Wear work gloves. Remove the washer's console and then the spring clips that secure the top/body assembly to the washer frame, using a putty knife to gently release them. With the body lifted or set aside, locate the capacitor — a black cylindrical component mounted to the rear panel, held in place by a small plastic retaining clip. Using a flat-blade screwdriver, gently pop the plastic clip away from the capacitor to release it. After confirming the capacitor is fully discharged, unplug it from the appliance wiring. Remove the foam shield from the old capacitor and transfer it onto the new one before installing — this shield protects the capacitor from moisture, and skipping it leaves the new part more exposed to washer humidity. Connect the new 8572717 capacitor to the wiring, snap it back into the plastic retaining clip in the same position, and reassemble the body, spring clips, and console in reverse order. Restore power and run a test cycle to confirm the motor starts promptly on both agitate and spin. Tools needed: putty knife, flat-blade screwdriver, Phillips screwdriver, insulated-handle screwdriver or capacitor discharge tool, work gloves. Frequently Asked Questions My washer motor hums but won't start. Is this the right part? Yes, this is the classic symptom of a failed start capacitor. Since this capacitor's entire job is delivering the momentary voltage boost needed to get the motor spinning from a standstill, a failure here often leaves the motor energized and humming but unable to actually overcome its own inertia and start turning. What's the difference between a start capacitor and a run capacitor? A start capacitor works only for a brief moment — it delivers a strong voltage boost the instant the motor is told to start, then a relay switches it out of the circuit once the motor reaches running speed. A run capacitor, by contrast, stays in the circuit continuously while the motor operates, correcting current phase for efficiency. Because the start capacitor works so hard in such a short burst on every single start, it's a more common failure point than a run capacitor on this type of motor. Do I need to reuse the foam shield from my old capacitor? Yes, it's worth transferring. The foam shield wraps around the capacitor to protect it from moisture inside the washer cabinet, and reusing it on the new capacitor helps the replacement hold up the same way the original was designed to. If the foam has degraded significantly, you can skip it, but it's a simple step that adds meaningful protection. My old capacitor got hot and smoked. Is that dangerous? Yes — a capacitor that overheats to the point of smoking has failed in a way that can pose a fire or electrical hazard, and the washer should not be used again until it's replaced. This kind of failure typically happens when a capacitor stays energized longer than it should, generating heat it isn't designed to dissipate. Replace the capacitor and, if the washer's start relay or timer seems to be holding the capacitor in the circuit too long, have that checked as well. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured to match the electrical specifications (189–227 MFD, 125VAC, 60Hz), cylindrical form factor, and mounting configuration of the original WP8572717 start capacitor used in compatible Whirlpool, Kenmore, Maytag, KitchenAid, and related top-load washers and washer/dryer combos. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

131758600 Washer Genuine OEM Timer Replaces Part Numbers: 131758600, AP2107583, PS418697. Description: This washer timer is a Genuine OEM part for select Frigidaire washing machine models. This timer controls the various cycles of the washing machine, including wash, rinse, and spin cycles. By regulating the duration and sequence of each cycle, the timer ensures that the washing machine operates smoothly and efficiently.

Read more less

 WH42X10650 Washer Control Panel, White Replaces Part Numbers: WH42X10650, AP3995175, 1264621, AH1482468, EA1482468, PS1482468. The WH42X10650 is a genuine GE replacement part, specifically designed as a control panel for GE washing machines. It houses and operates the control buttons and display, ensuring compatibility and reliability for your appliance.

Read more less

WH12X10527 Washer Genuine OEM Timer Replaces Part Numbers: WH12X10527, AP5645215, PS4704240. Description: This washer timer is a Genuine OEM part for select GE washing machine models. This timer controls the various cycles of the washing machine, including wash, rinse, and spin cycles. By regulating the duration and sequence of each cycle, the timer ensures that the washing machine operates smoothly and efficiently.

Read more less

WP3363003 Washer Upper Agitator Fits Specific Top Load Washer Models. Replaces Part Number: WP3363003, 3363003, 2654, AP6008106, PS11741237. Description: The Upper Agitator is an OEM part designed for select Kenmore, Whirlpool top-loading washing machines. 

Read more less

WH22X37840 Genuine OEM GE Washer Main Control Board The WH22X37840 is a genuine GE OEM main control board for GE and Profile UltraFresh front-load washers. This board is the washer's central processor — it reads every button press and cycle selection, drives the motor and inverter, opens and closes the water valves, runs the drain pump, and continuously monitors water level through an integrated water pressure switch built into the board itself. Because so many functions route through this single board, a failing control board can produce almost any symptom: a washer that won't power on, won't start a cycle, stalls partway through, fails to fill or drain, or runs a cycle that doesn't match what was selected on the display. This board revises and supersedes WH22X36637, and also replaces WH22X29532, WH22X30898, WH22X32057, WH22X32457, WH22X34659, WH22X35517, WH22X36857, and WH22X37839. As a genuine OEM part, the WH22X37840 is manufactured by GE to factory specifications — guaranteed fit, materials, and performance. Important: this board is not universal across GE's front-load lineup. It must be matched to your specific model and, after installation, programmed with the correct "personality" code for your washer before it will operate properly. Quick Answer The WH22X37840 Genuine OEM GE Washer Main Control Board fixes GE and Profile UltraFresh front-load washers that won't power on, won't start, stall mid-cycle, fail to fill or drain, run the wrong cycle, or have an unresponsive control panel. Genuine OEM, includes an integrated water pressure switch. Revises WH22X36637; also replaces WH22X29532, WH22X30898, WH22X32057, WH22X32457, WH22X34659, WH22X35517, WH22X36857, WH22X37839. Fits GFW650S, GFW850S, PFW870S, and PFW950S platforms. Requires programming a model-specific "personality" code after install, and the drain pump must be confirmed good before installing — a failed pump can damage a new board. Common Problems This Part Fixes Washer won't power on or the display stays completely dark Washer won't start a cycle even though buttons respond and lights come on Cycle stalls or stops partway through with no error explanation Washer won't fill with water, or fills but never advances to wash Washer won't drain or won't spin at the end of a cycle Control panel unresponsive — button presses do nothing, or the wrong cycle runs Display shows scrambled characters, flashing LEDs, or a persistent error code Washer runs erratically — random starts, stops, or cycle changes on its own Board that failed after repeated cycles where the drain pump was struggling Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer main control board directly replaces the following OEM and cross-reference part numbers: WH22X37840, WH22X36637, WH22X35517, WH22X34659, WH22X30898, WH22X29532, WH22X32057, WH22X32457, WH22X36857, WH22X37839, AP7245609, AGE26864, PD00089582, PS17874601. WH22X36637 was the immediately preceding number that GE revised to WH22X37840. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This main control board is compatible with select GE and Profile UltraFresh front-load washers, including: GE front-load washers — GFW650S series GE front-load washers — GFW850S series GE Profile front-load washers — PFW870S series GE Profile front-load washers — PFW950S series Verified model numbers include: GFW650SPN0SN, GFW650SPN1SN, GFW650SPN3SN, GFW650SPN4SN, GFW650SSN4WW, and PFW955SPW0DS. Note: This board only works for the specific GE and Profile models listed above and must be programmed with the correct personality code for your washer after installation. It is NOT a universal front-load control board. If your model number is not listed above, ordering this board is likely to result in a board that installs but never runs correctly. Always verify your full model number before ordering, and contact our support team with your model number if you're unsure. Key Features Genuine GE OEM part — factory-specified firmware, relay switching, and sensor interface Functions as the washer's central processor, coordinating the motor, inverter, water valves, and drain pump Includes an integrated water pressure switch — not available or serviceable as a separate part Resolves "won't power on," "won't start," "stalls mid-cycle," "won't fill or drain," and "unresponsive control panel" symptoms caused by control board failure Revises and directly replaces WH22X36637 and 7 additional legacy board numbers Direct drop-in replacement for the original board mounting and harness connectors Fits GFW650S, GFW850S, PFW870S, and PFW950S GE and Profile UltraFresh platforms Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number WH22X37840 Part Type Washer Main Control Board (Electronic Control Module) Condition Genuine OEM Brand GE / GE Profile Application GE and Profile UltraFresh Front-Load Washers Integrated Components Water pressure switch (built into board, not separately serviceable) Programming Required Yes — model-specific personality code must be set after installation Supersedes WH22X36637 Repair Difficulty Medium — top panel removal and electrical connections required Quantity 1 control board Compatible Models GFW650S, GFW850S, PFW870S, PFW950S series Installation Notes ⚠️ 240V Circuit — Unplug Washer Before Starting. Verify Drain Pump First. Board Requires Programming. Disconnect power at the outlet or shut off the circuit breaker before beginning; front-load washers on this platform run on a 120V/240V circuit and internal components can retain a charge briefly after power is removed. Before replacing the board, confirm the drain pump is working correctly. A drain pump that has been struggling, clogged, or intermittently failing can send the control board erratic electrical feedback that damages a brand-new board the same way it damaged the old one — replacing the board alone, without checking the pump, is one of the most common reasons a "new" board fails again within days. Access is typically through the top panel: remove the rear top screws and slide the panel back, then locate the control board housing (commonly behind the top-front console or in a housing near the top of the cabinet, depending on model). Photograph all harness connections before disconnecting anything — this board has numerous connectors and getting even one out of place will cause a no-start or miswired symptom. Ground yourself before handling the board to avoid static damage to its electronics. Remove the mounting screws, disconnect each harness connector, and lift the old board free. Install the new WH22X37840 in the same orientation, reconnect every harness connector exactly as photographed, and secure the mounting screws. Before closing the washer back up, you must program the board with the personality code specific to your model. This is done through a button sequence on the control panel — press and release Start repeatedly until the display shows the personality ID number for your model, then confirm to save it; the control will return to an idle state once accepted. GE's official instructions (publication 99-3000289) detail the exact sequence and a Field Service Mode test if the LEDs don't flash correctly after programming — follow those instructions rather than guessing at the code, since an incorrect personality setting will cause the washer to behave unpredictably. Once programmed, reassemble the top panel, restore power, and run a full test cycle to confirm normal fill, wash, drain, and spin behavior. Tools needed: Phillips screwdriver, nut driver, anti-static wrist strap (recommended), and access to GE's personality programming instructions for your model. Frequently Asked Questions Do I really need to program the board after installing it? Yes — this is not optional. The WH22X37840 is shared across several GE and Profile washer models, and it needs to be told which specific model it's installed in through a "personality" code before it will run correctly. Skipping this step, or entering the wrong code, will leave the washer behaving unpredictably even though the board itself is functioning normally. GE provides official programming instructions (publication 99-3000289) with the button sequence for your model — follow those closely rather than guessing. Why does the listing say to check the drain pump before installing this board? Because on this platform, a failing or clogged drain pump can feed electrical strain back into the control board that damages it over time — the same failure that likely killed your original board. If you install a new board without addressing a bad drain pump, there's a real risk of burning out the replacement as well. Before installing, run the pump through a diagnostic or physically inspect it for clogs, a seized impeller, or electrical failure, and address any issues found there first. My washer won't power on at all. Is this the right part? It's a strong candidate, but rule out the obvious first: confirm the outlet has power, check that the washer's power cord and connection are intact, and check the home's circuit breaker or a blown fuse. If those are all fine and the washer still shows zero signs of life — no lights, no display, no response to any button — the main control board has very likely failed and this board is the correct replacement. What's the difference between WH22X37840 and WH22X36637? They are the same board across production revisions. WH22X36637 was the prior GE part number and WH22X37840 is the current number that supersedes it. If your washer's parts diagram shows WH22X36637 or any of the older numbers (WH22X29532, WH22X30898, WH22X32057, WH22X32457, WH22X34659, WH22X35517), this listing is the correct replacement — it installs and programs the same way. Does this board include the water pressure switch? Yes. The water pressure switch that monitors fill level is integrated directly into this control board and is not available as a separate part per GE. If your washer's issue turns out to be water-level detection specifically — overfilling, underfilling, or an error related to water level — this board is the correct and only OEM fix, since the pressure switch cannot be replaced on its own. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by GE to factory specifications — guaranteed fit, materials, and performance. It carries the same firmware, relay switching, integrated water pressure switch, and harness layout as the control board originally installed in your washer, and it is the officially supported replacement for your model once the correct personality code is programmed. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

WH12X10614C Washer Genuine Electronic Control Board Replaces Part Number: WH12X10614C, WH12X10614, WH12X10538, AP8056060.

Read more less

W11248040 Washer Console (Control Panel Housing) Genuine Whirlpool part Replaces Part Number W11248040, 4845509, W11035013, W11120176, W11192407, PD00087512, EAP12584120, AP6783239, PS12584120. Model Cross Reference This part #W11248040 works with all models listed. Kenmore / Sears 110.27132412 Washer Kenmore / Sears 110.27132413 Washer  

Read more less

285727 Washer Agitator Assembly  Fits Specific Top Load Washer Models. Replaces Part Number: 285727, 285559, 295559, 3347674, 3361598, 470865, AH334617, EA334617, AP3094515, PS334617. Description: The Agitator is a Genuine OEM part designed for select Kenmore, Whirlpool top-loading washing machines. It sits at the bottom of the wash tub and plays a key agitation role during cycles.

Read more less