XPARTCO 6501KW2002B Washer Rotor Position Sensor – Compatible with LG and Kenmore Washers Product Description Maintain smooth spin cycles and precise motor control with the XPARTCO 6501KW2002B Washer Rotor Position Sensor. This Sensor Assembly, also known as a hall sensor is a replacement Part and is a vital component in Specific LG, Kenmore washer Models. This part monitors the direction and speed of the spinning rotor. It then communicates this information to the electronic control board. By doing so, it aids in the precise operation of your washer. If your washer pumps but fails to spin or agitate, it may be indicative of a damaged sensor assembly. Replaces Part Numbers 6501KW2002B, 6501KW2002A, AP7015078, PD00073205, EAP16556422, 4962510, PS16556422, EAP16556422. Compatibility This replacement rotor position sensor fits select LG and Kenmore front-load washers. Example compatible models include (but are not limited to): LG WM2487HRM, LG WM0642HW, and Kenmore 796.40272900. Always verify your washer’s model number before ordering. Contact our support team if you’re unsure. Key Features Aftermarket Replacement – Designed to match OEM performance and precision Accurate Rotor Feedback – Helps regulate motor speed and direction for smooth washing Cost-Effective Fix – Delivers OEM-level performance at a fraction of the price Plug-and-Play Installation – No wiring modification required Fixes Common Issues – Resolves LE, UE, SE, and spin cycle errors Product Specification Part Number: 6501KW2002B Component Type: Washer Rotor Position Sensor (Hall Sensor) Material: Durable printed circuit board with reinforced plastic housing Mounting: Direct-fit installation on stator assembly Operating Conditions: Rated for high-humidity, high-vibration washer environments Compliance: Built to OEM-equivalent quality standards (not OEM) Installation Notes Tools Needed: 10 mm socket wrench, Phillips screwdriver ⚠️ Safety First: Always unplug the washer before performing repairs to prevent electrical shock. Steps: Disconnect power and remove the rear access panel. Unscrew the rotor bolt and carefully remove the rotor assembly. Locate and unplug the old sensor from the stator. Install the new XPARTCO 6501KW2002B sensor, aligning mounting tabs. Reconnect the wiring harness, reinstall the rotor, and secure the panel. Restore power and run a spin test to verify correct operation. ⏱️ Time Required: 20–25 minutes Shop With Confidence Trusted Appliance Parts Supplier 30-Day Return Policy Restore precise washer performance — Add to Cart Now for a reliable, budget-friendly repair!

Read more less

XPARTCO W10006355 Washer Shift Actuator  Fits specific Maytag, Kenmore, Whirlpool top-load machine models. Replaces Part Numbers: WPW10006355, W10006355, AP6014711, PS11747977. Description: This Shift Actuator is a replacement part for specific Maytag, Kenmore, Whirlpool washing machine models. It is an electronic component located inside the transmission that controls the shifting between wash cycles. The shift actuator receives signals from the washer control board to change modes, initiating proper movements to advance the cycle.   This is an aftermarket part that can be used as a replacement for the OEM part.

Read more less

W11244231 Genuine OEM Whirlpool Washer Drain Hose The W11244231 is a genuine Whirlpool OEM drain hose for Whirlpool, Maytag, Kenmore, Amana, Crosley, Admiral, Inglis, and Roper washers. This flexible tube carries used water from the washer tub to your house drain after every wash cycle, connecting the washer's outlet to your standpipe or utility sink drain connection. This hose is approximately 4 feet long and ships as a kit that includes a clamp. Over time, normal wear and tear, exposure to high water pressure or temperature, or physical damage from kinks and pinches can cause the hose to crack, bulge, or leak. A failing drain hose typically shows up as water leaking around the hose connections or along its length, slow or improper draining, or visible cracks and bulges in the hose material. It directly replaces W10221546, W10769870, W10821090, W11203364, W11249137, W10826733, W11199768, W11199820, AP6339776, and PS12578897. Quick Answer The W11244231 Genuine OEM Whirlpool Washer Drain Hose fixes Whirlpool, Maytag, Kenmore, Amana, Crosley, Admiral, Inglis, and Roper washers with a cracked, bulging, or leaking drain hose, slow draining, or a missing hose. Approximately 4 feet long, includes clamp. Replaces W10221546, W10769870, W10821090, W11203364, W11249137, W10826733, W11199768, W11199820, AP6339776, PS12578897. This is a separate part from our W11281268 drain hose listing, which fits a different set of washer models — always confirm your exact model number before ordering. Common Problems This Part Fixes Water leaking around the hose connections or along its length Slow draining or improper drainage of the tub Visible cracks, bulges, or damage to the hose material Missing drain hose on a newly acquired or moved washer Reduced washer efficiency from a clogged, worn, or damaged hose Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer drain hose directly replaces the following OEM and cross-reference part numbers: W11244231, W10826733, W10221546, 4814009, W10769870, W10821090, W11199768, W11199820, W11203364, W11249137, AP6339776, AWP43752, OEM19019337, PD00045186, PS12578897 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This drain hose is compatible with select Whirlpool washers, and also fits select Maytag, Kenmore, Amana, Crosley, Admiral, Inglis, and Roper washers built on the Whirlpool platform, spanning Whirlpool series 1CWTW4, 2DWTW, 3DWTW, 3LWTW, 3NWTW4800, 3SWTW4800, and 4GWTW, and Maytag series 3LMVWC, 4GMVW, 4KMVW, 4KNTW, 7MMVW, and MVWX6, including specific model numbers such as: MVWX655DW1, NTW4516FW3, VAW3584GW0 WTW4816FW2, WTW5000DW1, WTW5000DW2, WTW5000DW3, WTW9500EC0 WTW5100HC0, WTW5500BW0, WTW5600XW0, WTW5700AC0, WTW5800BC0, WTW6120HC0 WTW7000DW0, WTW8000DW0 ITW4871FW0, ITW4871FW1, ITW4871FW2 4KMVWC415FW0, 4KMVWC430JW0, 7MWTW1504DQ0 Kenmore 11026112310 Note — not the same as W11281268: This is a separate part from our W11281268 drain hose listing, which fits a different set of Whirlpool, Maytag, and Amana washer models with its own cross-reference set. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure which hose your washer needs. Key Features Genuine Whirlpool OEM part — factory-specified length and fitting design Carries wastewater from the washer to your house drain during the drain cycle Resolves "leaking around connections," "slow draining," and "cracked or bulging hose" symptoms Approximately 4 feet long Ships as a kit including a clamp Direct drop-in replacement — matches the original fitting and length Replaces W10221546, W10769870, W10821090, W11203364, W11249137, W10826733, W11199768, W11199820, AP6339776, and PS12578897 Compatible with Whirlpool, Maytag, Kenmore, Amana, Crosley, Admiral, Inglis, and Roper washers Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number W11244231 Part Type Washer Drain Hose Kit Condition Genuine OEM Brand Whirlpool Length Approx. 4 feet Includes Clamp Related Part W11281268 (6' hose, different model fitment, sold separately) Repair Difficulty Easy — basic hand tools, novice repair experience Quantity 1 drain hose kit Compatible Brands Whirlpool, Maytag, Kenmore, Amana, Crosley, Admiral, Inglis, Roper Installation Notes ⚠️ Unplug Washer And Shut Off Water Supply Before Starting — Transfer Your Old Clamps To The New Hose Disconnect power at the outlet, or shut off the house circuit breaker for the appliance, and shut off the water supply before beginning. Wear work gloves. Remove the back panel of the washer, then the lower front access panel to access the drain hose connection. Place a towel down before disconnecting any hoses to catch any remaining water. Disconnect the old hose from the washer's outlet spout and from your standpipe or drain connection. Transfer your existing hose clamps onto the new W11244231 hose during installation. Fit the new hose over the outlet spout and secure the clamp, then reconnect the other end to your house drain. Reinstall the lower front access panel and back panel. Restore the water supply and power, then run a test cycle to confirm the hose is secure with no leaks. Tools needed: multi-screwdriver, standard pliers, work gloves, towel. Frequently Asked Questions My washer is leaking. Is this the right part? It's worth checking, especially if the leak appears to come from around the hose connections or along its length rather than from the washer's tub or valve area. A cracked, bulging, or worn drain hose is a documented cause of leaking and can be resolved by replacing the hose to restore proper drainage. Is this the same as your W11281268 listing? No, these are two separate genuine Whirlpool drain hoses that fit different sets of washer models, with their own distinct cross-reference lists. Always confirm your exact model number against the compatibility list for each listing rather than assuming either hose is a universal fit. Do I need to buy new hose clamps separately? This hose kit includes a clamp, but you'll still need to transfer your existing clamps from the old hose for any connections that don't come with a new one included. Keep your old hardware on hand during the swap rather than discarding it with the old hose. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by Whirlpool to factory specifications — guaranteed fit, materials, and performance. It matches the original length and fitting configuration of the drain hose originally installed on your washer. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

EXPW79SC (4 Pack) Washing Machine Fill Hose Gasket with Screen 4 Pack compatible with 5/ 8 inch washing machine and 3/4 inch garden hose Fine Screen the rubber washer with stainless steel filter mesh, serves as a flow restrictor can reduce the waste of water effectively     

Read more less

XPARTCO 5304511335 Washer Water Level Pressure Switch – Compatible with Frigidaire & Electrolux Washers Product Description Restore accurate water level control and proper washer operation with the XPARTCO 5304511335 Washer Water Level Pressure Switch. It is responsible for detecting the water level inside the washer tub and ensuring accurate water level control during the wash cycle. It detects the pressure changes caused by the water level, allowing the washer to adjust the water intake accordingly. A faulty pressure switch can cause overfilling, under-filling, or cycles not advancing properly. Replacing it with this reliable XPARTCO component helps ensure correct water levels and consistent wash performance. XPARTCO provides cost-effective aftermarket appliance parts engineered to match original fit and function. Replaces Part Numbers 5304511335, 4584277, EAP12176459, AFR17584, OEM18784872, PD00046588, AP6261621, PS12176459. Compatibility This replacement washer water level pressure switch fits select Frigidaire, Electrolux, Gibson, Crosley, and Kenmore (Frigidaire-manufactured) washers. Common compatible models include (but are not limited to): Frigidaire FFTW4120SW1, FFTW4120SW0, FFTW4120SW, FFTW4120SW0 Always verify your washer’s model number before ordering.Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement – Matches OEM fit and pressure sensing performance 💧 Accurate Water Level Detection – Ensures proper fill and cycle control ⚙️ Fixes Common Issues – Resolves overfill, underfill, and cycle errors 🧩 Direct-Fit Design – Installs easily with existing hose and wiring 💰 Cost-Effective Repair – Affordable alternative to OEM pressure switches ⚠️ Symptoms If your washer is experiencing any of the following issues, this part may need replacement: 💧 Washer overfilling or underfilling ⚠️ Incorrect water levels during cycles 🔄 Cycle not advancing properly 🛑 Washer stops mid-cycle 🚫 No water or continuous filling Replacing this pressure switch can restore proper water level control and washer performance. 📐 Product Specification Part Number: 5304511335 Component Type: Washer Water Level Pressure Switch Function: Detects water level and signals control board Connection Type: Air hose + electrical connector Application: Washer water level sensing system Quality Level: Aftermarket replacement (not OEM) 🛠️ Installation Notes Tools Needed: Phillips screwdriver ⚠️ Safety First: Unplug the washer before servicing to avoid electrical shock. Basic Steps: Disconnect washer power. Access the control panel or top panel. Locate the pressure switch and disconnect the air hose and wiring. Remove mounting screws and remove the old switch. Install the new XPARTCO 5304511335 pressure switch. Reconnect hose and wiring, reassemble, and restore power. Run a test cycle to verify correct water levels. ⏱️ Time Required: 20–30 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Aftermarket Appliance Parts 🔄 30-Day Return Policy Restore accurate water level control and reliable washer performance — Add to Cart Now for a dependable repair!

Read more less

XPARTCO 6501KW2001A Washer Rotor Positioning Sensor – Compatible with LG and Kenmore Washers Product Description Restore accurate motor control and spin performance with the XPARTCO 6501KW2001A Washer Rotor Positioning Sensor. This Sensor Assembly, also known as a hall sensor is a replacement Part and is a vital component in Specific LG, Kenmore washer Models. This part monitors the direction and speed of the spinning rotor. It then communicates this information to the electronic control board. By doing so, it aids in the precise operation of your washer. If your washer pumps but fails to spin or agitate, it may be indicative of a damaged sensor assembly. Replaces Part Numbers 6501KW2001A, 6501KW2001D, PD00001726, EAP2497738, 6501KW2001C, EBR37560301, AP4457567, PS3529185.  Compatibility This replacement rotor positioning sensor fits select LG and Kenmore front-load washers. Example compatible models include (but are not limited to): LG WM2101HW, LG WM2487HRM, and Kenmore 796.40272900. Always verify your washer’s model number before ordering. Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement – Designed to match OEM performance and accuracy ⚙️ Precise Motor Feedback – Helps control drum rotation and spin speed 💰 Cost-Effective Solution – High-quality alternative to OEM sensor assembly 🛠️ Easy Installation – Plug-and-play design with secure connector fit 🛡️ Fixes Common Issues – Resolves LE, UE, or spin-related error codes 📐 Product Specification Part Number: 6501KW2001A Component Type: Washer Rotor Position Sensor (Hall Sensor) Material: High-durability circuit board and plastic housing Mounting: Direct-fit replacement on motor stator assembly Operating Conditions: Designed for high-humidity washer environments Compliance: Built to OEM-equivalent quality standards (not OEM) 🛠️ Installation Notes Tools Needed: 10mm socket wrench, Phillips screwdriver ⚠️ Safety First: Always unplug the washer before performing any repairs to prevent electrical shock. Steps: Disconnect power and remove the rear access panel. Remove the rotor bolt and pull off the rotor assembly. Locate and disconnect the wiring harness from the old sensor. Remove the old 6501KW2001A sensor and install the new XPARTCO replacement. Reconnect wiring, reinstall the rotor, and secure the rear panel. Restore power and run a spin test to verify repair. ⏱️ Time Required: 20–25 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Appliance Parts Supplier 🔄 30-Day Return Policy Fix washer spin and motor issues — Add to Cart Now for a reliable, budget-friendly repair!

Read more less

XPARTCO WH16X29509 Washer Damper Vent The XPARTCO WH16X29509 is an aftermarket replacement washer damper vent compatible with select GE, Hotpoint, RCA, and Kenmore front-load washers in the GFW510, GFW550, and GFW650 series. The damper vent is a one-way flap valve located on the drain system that automatically opens during draining to equalize pressure inside the drain pipe, allowing water to drain quickly and completely. When closed, it seals the drain path to prevent backflow of residual dirty water and lint from re-entering the drum and soiling clean laundry. Made from high-strength plastic with a reinforced hinge mechanism, this damper vent is designed to resist deformation under high-frequency operation and to prevent lint accumulation that can cause blockages. It directly replaces OEM part numbers WH16X29509, 4982970, AP6990392, and several additional cross-reference numbers. Snap-in installation requires no special tools and takes just minutes to complete. Quick Answer The XPARTCO WH16X29509 Washer Damper Vent fixes GE front-load washers displaying error codes 38, 39, 40, or 84, draining slowly, or returning dirty water or lint to clean clothes. The damper opens during draining and closes to block backflow. Compatible with GE GFW510, GFW550, and GFW650 series. Snap-in installation — no tools required. Common Problems This Part Fixes Slow or incomplete draining during the wash or spin cycle Dirty water or lint backflowing into the drum and soiling clean laundry Washer not draining fully, leaving standing water in the drum Drain hose blockages caused by a stuck or failed damper vent flap Moisture or odor buildup inside the washer due to poor drain ventilation Replaces Part Numbers This washer damper vent directly replaces the following OEM and cross-reference part numbers: WH16X29509, EAP16219913, FIX16219913, AGE26992, PD00079480, AP6990392, PS16219913. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This damper vent is compatible with select front-load washers from the following brands and series: GE front-load washers — GFW510 series GE front-load washers — GFW550 series GE front-load washers — GFW650 series GE front-load washers — GFW850 series (select models) GE Profile front-load washers — PFW series (select models) Hotpoint front-load washers (select models) RCA front-load washers (select models) Kenmore / Sears front-load washers (select GE-built models) Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features One-way flap valve — opens automatically during draining to equalize pipe pressure and ensure fast, complete drainage Seals shut when not draining — blocks residual dirty water and lint from backflowing into the drum and re-soiling clean laundry High-strength plastic construction with reinforced hinge — resists deformation under high-frequency operation Optimized airflow design minimizes lint accumulation for long-lasting, clog-free performance Heat-resistant materials — withstands high-temperature wash programs Direct replacement for WH16X29509 — snap-in installation, no special tools required Aftermarket replacement built to OEM-equivalent quality standards Product Specifications Part Number WH16X29509 Part Type Washer Damper Vent (Drain Vent Flap Valve) Condition Aftermarket Replacement Application Front-Load Washers Function Equalizes drain pipe pressure during draining; blocks backflow when closed Material High-strength plastic Installation Snap-in — no special tools required Error Codes Resolved 38, 39, 40, 84 (on compatible GE models) Compatible Series GFW510, GFW550, GFW650, GFW850, PFW (select models) Compatible Brands GE, Hotpoint, RCA, Kenmore Installation Notes ⚠️ Unplug Washer Before Starting Unplug the washer from the power outlet before beginning any repair. The damper vent is located in the drain system — typically accessible from the front lower panel or by removing the washer's access panel. Locate the existing damper vent on the drain hose or drain port. Press the tabs or release clips to remove the old damper vent from its snap-in mounting position. Align the new WH16X29509 damper vent with the mounting port and press firmly until it snaps into place. Restore power and run a short drain or rinse cycle to verify the washer drains correctly and no error codes are displayed. Tools needed: None for the damper vent itself; a screwdriver may be needed to remove the access panel on some models. Frequently Asked Questions What does the washer damper vent do? The damper vent is a one-way valve on the washer's drain system. During the drain cycle, it opens automatically to equalize the air pressure inside the drain hose, which allows water to drain quickly and completely. When draining stops, the flap closes to create a seal that prevents residual wastewater and lint from flowing back up the drain hose and into the drum — which would re-soil clothes that have already been washed. What error codes does a failed damper vent cause on GE washers? A blocked, stuck, or failed WH16X29509 damper vent is a known cause of error codes 38, 39, 40, and 84 on compatible GE GFW510, GFW550, and GFW650 series front-load washers. These codes are typically triggered when the control board detects a drain pressure or flow issue. Replacing the damper vent resolves the issue in many cases when the drain pump and hose are otherwise clear. How do I know if my damper vent has failed? Common signs of a failed damper vent include slow or incomplete draining, one of the error codes listed above, dirty water or lint reappearing on clothes after a wash cycle, or a stuck flap that is visibly open or closed when it should not be. You can inspect the damper vent by removing the access panel and checking whether the flap moves freely — it should open easily when you apply gentle pressure and spring closed when released. Is the WH16X29509 compatible with GE Profile and GE Café washers? The WH16X29509 is confirmed compatible with select GFW and PFW series models from GE and GE Profile. GE Café washers use different model series — verify your specific model number before ordering. Contact our support team if you need help confirming compatibility for your Café or Profile model. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine GE OEM part, but is manufactured from high-strength plastic to match the dimensions and performance of the original WH16X29509 damper vent. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout  

Read more less

AAS73229402 Genuine OEM LG Washer Tub to Pump Hose The AAS73229402 is a Genuine OEM LG replacement tub-to-pump hose (also called a drain pump bellows assembly) compatible with a wide range of LG and Kenmore washing machines. This hose carries water from the outer tub to the drain pump, allowing the used wash and rinse water to properly empty from the tub during the drain cycle. It features flexible bellows that let the hose expand and contract as the tub moves during operation, while forming a watertight connection between the tub and the pump. When this hose cracks, splits, or develops porous areas, water leaks out during draining — typically showing up as a puddle under the washer. Made of durable rubber engineered to resist wear through years of flexing and water exposure. As a Genuine OEM part manufactured by LG to factory specifications, the AAS73229402 directly replaces AP6973533, AGM76891101, AHA75673401, and AEM74073303. This is one of those repairs where using the exact OEM hose matters — the correct fit and internal diameter ensure proper drainage and a leak-free seal, which unverified substitute hoses can't always guarantee. Installs in 30–60 minutes with basic hand tools. Quick Answer The AAS73229402 Genuine OEM LG Washer Tub to Pump Hose fixes LG and Kenmore washers that leak water under the machine during or after draining, don't fully drain the tub, leave standing water, or develop mold in the pump housing. Tub-to-pump hose / drain pump bellows assembly with flexible bellows — carries water from the outer tub to the drain pump. Genuine OEM. Replaces AP6973533, AGM76891101, AHA75673401, AEM74073303. Compatible with LG front-load and top-load washers plus select Kenmore models. Use the exact OEM hose for correct fit and diameter. Common Problems This Part Fixes Water leaking or puddling under the washer during or after the drain cycle Washer not fully draining — water left in the tub after the cycle Excess water left in the tub requiring additional emptying Drips or leaks from the tub-to-pump connection Standing water or mold growth inside the pump housing Hose visibly cracked, split, or showing porous/worn areas Hose no longer staying securely attached to the tub or pump Musty/moldy smell from water trapped by a leaking or sagging hose Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This tub-to-pump hose directly replaces the following OEM and cross-reference part numbers: AAS73229402, AAS73229405, AAS73229403, AGM76891101, AP6973533, PS12738715, ALG52189, PD00071151. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. For a proper leak-free seal, use the exact OEM hose rather than an unverified substitute — the correct fit and internal diameter matter. Compatibility This tub-to-pump hose is compatible with select LG and Kenmore washing machines, including front-load and top-load models: LG front-load washers — select WM-series models LG top-load washers — select WT-series models (including WT7305CV and related) LG washers using the AAS73229402 tub-to-pump bellows hose (verify with your parts diagram) Kenmore / Sears washers — select LG-built models Because LG uses several different tub-to-pump and drain hoses across its washer lineup, always verify your appliance model number before ordering to confirm the AAS73229402 is the correct hose for your machine. Contact our support team if you're unsure. Key Features Genuine OEM part manufactured by LG to factory specifications — guaranteed fit and performance Tub-to-pump hose (drain pump bellows assembly) — carries water from the outer tub to the drain pump for proper draining Flexible bellows design — expands and contracts as the tub moves during operation while keeping a watertight seal Resolves "leaking under the washer," "won't fully drain," "standing water," and "mold in pump housing" symptoms when caused by a failed hose Durable rubber construction engineered to resist cracking, splitting, and porosity over years of use Correct OEM fit and internal diameter for proper drainage and a leak-free seal Replaces AP6973533, AGM76891101, AHA75673401, and AEM74073303 Compatible with LG front-load (WM-series) and top-load (WT-series) washers, plus select Kenmore LG-built models Genuine OEM — the exact part sourced from the manufacturer DIY repair — installs in 30–60 minutes with basic hand tools Product Specifications Part Number AAS73229402 Part Type Washer Tub-to-Pump Hose (Drain Pump Bellows Assembly) Condition Genuine OEM Application Front-Load & Top-Load Washing Machines (LG platform) Function Carries water from the outer tub to the drain pump Design Flexible bellows (expands/contracts with tub movement) Material Rubber Location Between the outer tub and the drain pump Compatible Brands LG, Kenmore Installation Notes ⚠️ Unplug Washer and Shut Off Water Before Starting — Wear Work Gloves — Drain the Tub First Unplug the washer and shut off the water supply before beginning. Wear work gloves to protect your hands. Drain any excess water from the washer before starting — the tub and hose still hold water that will spill out when you disconnect the hose, so have towels and a shallow pan ready. Pull the washer away from the wall to access the panels (on many models you can leave the water supply hoses connected and just unplug the electrical cord). The hose is accessed by removing the rear panel: remove the screws (often 4) securing the rear panel to the back of the washer and set the panel aside. On some front-load models, the top panel is removed instead — remove the top panel bracket screws, slide the top toward the rear, and lift it off. Locate the tub-to-pump hose connecting the outer tub to the drain pump. Photograph the hose routing and clamp positions before disconnecting. Use slip-joint pliers to squeeze and slide back the spring hose clamps at each end of the hose (and loosen any center clamp with a screwdriver). Pull the old hose straight off both connections. Note: on some models the clamp on the pump differs from other nearby hose clamps — mark them so you reinstall each in the right spot. Install the new AAS73229402 hose, seating it fully onto both the tub and pump fittings, and secure the clamps in their original positions using the existing clamps. Make sure the hose is seated all the way on and the clamps are secure — a hose that isn't fully seated will leak and make a large mess. Reinstall the panel, push the washer back into place, restore power and water, and run a rinse/spin cycle to test drainage and check for leaks. Tip: some people find it easier to tip the washer up a few inches on a couple of 2x4s for better access. Tools needed: Phillips screwdriver, slip-joint pliers, towels, shallow pan, work gloves. Frequently Asked Questions There's a puddle under my LG washer — is this hose the cause? It's one of the most common causes, yes. The tub-to-pump hose carries water under pressure from the tub to the drain pump, so when it cracks, splits, or develops a porous spot, water escapes during the drain cycle and puddles under the machine. Before ordering, inspect the hose and its connections: pull the washer out, remove the rear (or top) panel, and look for visible cracks, splits, or wet spots along the hose and at the clamps. Also check the drain pump itself and the other hoses, since a leak can come from several nearby points. If the tub-to-pump hose shows damage or the leak traces to it, this is the correct part. Many people replace the drain pump and hoses together as a "while you're in there" repair. What's the difference between the tub-to-pump hose and the drain hose? They're two different hoses. The tub-to-pump hose (this part, AAS73229402) is an internal hose that carries water from the outer tub to the drain pump inside the washer cabinet. The drain hose is the external hose that carries the water from the pump out of the washer to your standpipe, sink, or drain. If your leak is inside the cabinet or under the machine, it's often the internal tub-to-pump hose. If water is leaking where the external hose meets your drain, that's the drain hose. Make sure you're ordering the right one for your symptom. Can I use an aftermarket substitute hose instead? We recommend the exact OEM hose. Tub-to-pump hoses have to match the specific fit and internal diameter of your washer's tub and pump fittings to seal properly and drain correctly. Appliance technicians specifically caution against using unverified substitute hoses on LG washers because an incorrect fit or diameter can cause leaks or drainage problems. The AAS73229402 is the genuine OEM part with the correct dimensions for the models it fits, giving you a reliable, leak-free seal. If you're unsure whether this is the right hose for your model, send us your model number and we'll confirm. My washer won't drain fully and leaves standing water — is it this hose? It can be, though incomplete draining has a few possible causes. A tub-to-pump hose that has partially collapsed, kinked, or is leaking can reduce the water flow to the pump and leave water behind. But standing water is also commonly caused by a clogged pump, a blocked hose, or a failing drain pump. Inspect the tub-to-pump hose for kinks, sagging, cracks, and blockages first. Also check the drain pump inlet and clean out any debris. If the hose is damaged, replacing it with the AAS73229402 restores proper flow. If the hose is fine, the drain pump or a blockage is the more likely cause. Is this a Genuine OEM or aftermarket part? This is a Genuine OEM part manufactured by LG to factory specifications. It is the exact same tub-to-pump hose (drain pump bellows assembly) installed in compatible LG and Kenmore LG-built washers from the factory — guaranteed fit, materials, and performance, sourced directly from the manufacturer. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less