12238200001084 Genuine OEM Midea Dryer Bearing House Assembly (Drum Rear Bearing)
The 12238200001084 is a Genuine OEM Midea replacement bearing house assembly compatible with select Midea, Criterion, and Insignia electric and gas dryers, including the CDE41N1AW series. The bearing house assembly is mounted at the rear of the drum and houses the bearing that the rear drum shaft rotates within, supporting the back of the drum and allowing it to spin smoothly. Unlike front-mounted slide rollers used on some dryer platforms, this Midea design uses a rear bearing housing assembly to carry the load at the back of the drum.
When the bearing house assembly wears out — typically from age, lack of lubrication, or accumulated lint and debris — the drum no longer spins smoothly on its rear support, resulting in grinding, rumbling, or squealing noise, increased drum drag, and in advanced cases, visible wobble or binding of the drum during rotation. As a Genuine OEM part manufactured by Midea to factory specifications, the 12238200001084 is a complete bearing house assembly designed as a direct replacement for the original equipment component. Installs in 45–60 minutes with basic hand tools, as drum removal is required.
Quick Answer
The 12238200001084 Genuine OEM Midea Dryer Bearing House Assembly fixes Midea, Criterion, and Insignia dryers with grinding, rumbling, or squealing noise from the rear of the drum, increased drum drag, or visible drum wobble. Mounted at the rear of the drum — houses the bearing the rear drum shaft rotates within. Genuine OEM. Compatible with Midea CDE41N1AW and related Midea electric dryer platform models. Requires drum removal to access — a more involved repair than a front roller swap.
Common Problems This Part Fixes
- Loud grinding or rumbling noise from the rear of the drum during the drying cycle
- Squealing or squeaking noise as the drum rotates — worn or dry bearing surface
- Increased drag or resistance felt when manually rotating the drum by hand
- Drum wobbling or binding during rotation — worn bearing no longer providing stable support
- Excessive vibration during the drying cycle
- Visible wear, cracking, or lint/debris buildup in the bearing house area
- Drum scraping against the rear bulkhead due to lost bearing support
Replaces Part Numbers
This bearing house assembly directly replaces the following part number:
12238200001084, AP7154967, PS18167713
This is the Midea manufacturer part number used across the compatible Midea, Criterion, and Insignia dryer platform. Contact our support team with your model number if you need confirmation before ordering.
Compatibility
This bearing house assembly is compatible with select Midea, Criterion, and Insignia dryers, including:
- Midea CDE41N1AW electric dryer
- Midea MLE series electric dryers (select models — same drum/bearing platform)
- Criterion electric dryers built on the Midea platform (select models)
- Insignia electric dryers built on the Midea platform (select models)
Always verify your appliance model number before ordering. Contact our support team if you're unsure.
Key Features
- Genuine OEM part manufactured by Midea to factory specifications — guaranteed fit and performance
- Complete bearing house assembly — supports the rear of the drum and allows smooth, quiet rotation
- Houses the bearing that the rear drum shaft rotates within — a sealed-style design intended to resist lint intrusion
- Direct replacement for the original equipment bearing house assembly
- Compatible with Midea CDE41N1AW and related Midea, Criterion, and Insignia electric dryer platform models
- Installs in 45–60 minutes with basic hand tools (drum removal required)
Product Specifications
| Part Number |
12238200001084 |
| Part Type |
Dryer Bearing House Assembly (Drum Rear Bearing) |
| Condition |
Genuine OEM |
| Application |
Electric Dryers (Midea platform) |
| Location |
Rear of drum — houses rear drum shaft bearing |
| Compatible Brands |
Midea, Criterion, Insignia |
Installation Notes
⚠️ Unplug Dryer Before Starting — Wear Work Gloves Disconnect power before beginning. Wear work gloves — there are sharp sheet metal edges inside the dryer cabinet. Remove the lint filter housing screws, release the top panel locking clips with a putty knife, and lift the top panel. Remove the front panel to access the drum. Take a photo of the belt routing before disconnecting the drive belt from the idler pulley. Carefully lift the drum out of the cabinet and set it aside on a padded surface. Locate the bearing house assembly mounted at the rear bulkhead where the drum's rear shaft was seated. Remove the mounting screws or clips securing the old bearing house assembly and pull it free. Clean any accumulated lint or debris from the mounting area before installing the new part. Install the new 12238200001084 bearing house assembly in the same position and secure the mounting hardware. Reinstall the drum, re-route and reconnect the drive belt, and reassemble the front and top panels. Restore power and run a test cycle to confirm the drum rotates smoothly and quietly. Tools needed: Phillips screwdriver, putty knife, work gloves.
Frequently Asked Questions
What does the bearing house assembly do?
The bearing house assembly is mounted at the rear bulkhead of the dryer and houses the bearing that the rear drum shaft rotates within. It supports the back of the drum as it spins, allowing smooth, low-friction rotation throughout the drying cycle. Unlike dryer platforms that use front-mounted slide rollers or felt seals for drum support, this Midea design relies on a dedicated rear bearing housing to carry the structural load at the back of the drum. As the bearing wears, friction increases, leading to noise, drag, and eventually wobble or binding if left unaddressed.
How do I know if the bearing house assembly has failed versus another component?
A grinding, rumbling, or squealing noise specifically tied to drum rotation — rather than the blower motor or idler pulley — and noise that changes pitch as the drum speeds up or slows down often points to the rear bearing. With the dryer unplugged and the drum exposed (front panel removed), try rotating the drum by hand: if you feel noticeable resistance, grinding, or grittiness compared to a smooth, free rotation, the bearing house assembly has likely worn out and needs replacement.
Why does this repair require removing the drum?
The bearing house assembly is mounted at the rear bulkhead behind the drum, supporting the drum's rear shaft from the inside. There is no way to access this component without first removing the front panel and lifting the drum out of the cabinet. This makes it a more involved repair than swapping a front-accessible part like a belt or idler pulley, but it follows the same general dryer disassembly procedure used for accessing other internal drum components.
Should I inspect other components while the drum is out?
Yes — since the drum must already be removed to access the bearing house assembly, this is an excellent opportunity to inspect the drive belt, idler pulley, and any felt seals or gaskets around the drum opening for wear. Components in this drum drive system tend to wear together, and addressing multiple worn parts in a single repair session helps avoid a near-term repeat teardown.
Is this a Genuine OEM or aftermarket part?
This is a Genuine OEM part manufactured by Midea to factory specifications. It is the exact same bearing house assembly installed in compatible Midea, Criterion, and Insignia electric dryers from the factory — guaranteed fit, materials, and performance.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
