316530101 Genuine OEM Frigidaire Range Infinite Switch — Hyper Element
The 316530101 is the Genuine OEM infinite switch for the hyper element (radiant dual-zone surface burner) on select Frigidaire and Kenmore electric ranges. The infinite switch is the control behind your surface knob — it uses a bimetallic strip and internal contacts to cycle power on and off rapidly, creating a continuously variable heat level rather than fixed steps. When this switch fails, the burner loses the ability to hold a set temperature: it may stay on full blast, stay off entirely, or cycle erratically regardless of knob position.
Because the hyper element is a dual-zone unit — a smaller inner coil and a larger outer ring that activate at different power levels — its infinite switch carries higher internal loads than a standard single-element switch. The 316530101 is engineered specifically for this application, with contact ratings matched to the hyper element's power draw. Installing a standard-element switch in its place will result in premature contact failure and unreliable temperature control.
🔧 Quick Answer: Will This Fix Your Burner?
Replace this switch if your hyper element burner stays on full heat, won't turn on, or won't hold temperature at any knob setting. Part Number: 316530101 — Genuine OEM Frigidaire, hyper element application.
Common Symptoms This Part Fixes
- Hyper element burner stays on full power regardless of knob setting
- Burner won't heat at all after turning knob to any position
- Burner cycles on and off erratically with no stable heat output
- Only inner zone heats — outer ring fails to activate at higher settings
- Knob turns freely but burner doesn't respond to position changes
- Burning smell from control panel area during use
Replaces These Part Numbers
316530101 replaces 2210875, AFR16377, AH3506352, AP5330876, EA3506352, EAP3506352, OEM15992637, PD00055047, PS3506352
Compatible With
Compatible Brands
Frigidaire Kenmore
Fits select electric ranges with hyper element (dual-zone radiant) surface burners. Verify your model number before ordering.
Key Features
- Genuine OEM Frigidaire part — engineered for hyper element power ratings
- Bimetallic strip design provides continuously variable heat control
- Controls both inner and outer zones of the dual-zone hyper element
- Direct plug-in replacement — no wiring modifications needed
- Restores precise knob-position-to-heat-output response
- Fits select Frigidaire and Kenmore electric ranges
Specifications
| Part Number |
316530101 |
| OEM Part Number |
316530101 |
| Condition |
Genuine OEM |
| Part Type |
Infinite Switch — Hyper Element |
| Appliance Type |
Electric Range |
| Brand |
Frigidaire |
| Dimensions |
6.7"L × 5.8"W × 4.8"H |
| Weight |
0.49 lbs |
| Compatible Brands |
Frigidaire, Kenmore |
⚠ Safety Warning
Disconnect power to the range at the circuit breaker or by unplugging before beginning this repair. The control panel area carries 240V. Never work on the switch with power connected.
Frequently Asked Questions
What makes the hyper element switch different from a standard infinite switch?
A hyper (dual-zone) element has two separate heating coils — an inner and an outer ring — that activate at different knob positions. Its infinite switch must handle the combined load of both zones and route power correctly to each. Standard single-element switches are not rated for this load and will fail early if used as a substitute. Always confirm your burner type before ordering an infinite switch replacement.
How does an infinite switch work, and how do I know when it fails?
An infinite switch uses a bimetallic strip that heats and bends as current passes through it. That bending motion opens and closes internal contacts, cycling the element on and off at a rate proportional to the knob position. At low settings the contacts are open most of the time; at high settings they stay closed nearly continuously. When the bimetallic strip warps, the contacts pit or burn, or the cam mechanism wears out, the switch loses accurate control — it may default to full-on, full-off, or erratic cycling. These symptoms are specific to the switch and don't indicate a faulty element or control board.
Can I confirm the switch is bad before replacing it?
Yes. With the range unplugged, pull the control knob and disconnect the switch from its wiring harness. Use a multimeter set to continuity. At the LOW knob position, the switch's load contacts should cycle (you'll hear clicking). At the HIGH position, contacts should read continuous. No continuity at any position, or contacts that stick closed, confirms a failed switch. If the switch tests normal but the burner still misbehaves, check the element itself for visible breaks in the coil.
Is this a difficult repair to do myself?
This is a moderate DIY repair — typically 30–45 minutes. After disconnecting power, you'll remove the rear or side panel to access the control console, unplug the wiring harness from the old switch, unmount it, and install the new one. Take a photo of the wiring before unplugging — infinite switches can have multiple terminals and the connector orientation matters. The 316530101 is a direct plug-in replacement with no modification needed.
Will this switch also fix a burner that only heats on the inner zone?
Possibly. If the outer ring of your hyper element only activates at higher knob settings and has stopped doing so, a failed switch is a common cause — the contacts responsible for switching the outer zone on may be damaged while the inner zone contacts still work. That said, the outer coil of the element itself can also fail independently. Test the element with a multimeter (each coil should show continuity) to rule it out before replacing the switch.
✔ Genuine OEM Part ✔ Secure Checkout ✔ Compatibility Support ✔ Fast US Shipping
