Genuine OEM 5304522535 Washer Water Inlet Valve Assembly
The water inlet valve on an Electrolux front-load washer is the electrically controlled gate between your home's water supply and the wash tub. When the control board sends voltage to the valve's solenoid coils, internal plungers lift and water flows in. What makes the 5304522535 assembly different from a basic inlet valve is its built-in flow meter — a small turbine sensor that measures the exact volume of water entering the tub and reports it back to the control board, letting the washer fill to the correct level for each cycle and load size rather than relying on a pressure switch alone.
This is a genuine OEM Frigidaire part, manufactured by the same supplier that builds it for the factory assembly line. It is a direct replacement for the earlier 5304514791 valve assembly, which Frigidaire superseded with this updated version. The integrated flow meter is included — it is not sold separately on this assembly — so the entire valve-and-sensor unit installs as one piece.
Quick Answer
Will This Fix My Washer? Yes — if your Electrolux front-load washer won't fill with water, fills too slowly, overfills, leaks from the back near the hose connections, or stops mid-cycle with a water-related error, the Genuine OEM 5304522535 Water Inlet Valve Assembly is the most likely fix. This valve includes the integrated flow meter. Quick test: if unplugging the washer while it's filling stops the water, the valve solenoid is stuck open and needs replacing.
Common Symptoms of a Failing Water Inlet Valve
- Washer won't fill with water at all
- Water fills very slowly compared to normal
- Washer overfills or continues filling when it shouldn't
- Leaking from the back of the washer near hose connections
- Washer stops mid-cycle due to fill timeout
- Error codes related to water supply or fill level
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs. Below are the known cross-reference numbers for this valve assembly.
5304522535, 5304514791, AFR18813, AP6973371, EAP12731608, PD00084841, PS12731608
Compatibility
This water inlet valve assembly fits select Electrolux front-load washers:
- EFLW427UIW0 — 27" Front Load Washer with LuxCare Wash System
- EFLW427UIW1 — 27" Front Load Washer with LuxCare Wash System
- EFLW427UIW2 — 27" Front Load Washer with LuxCare Wash System
Note: This valve is listed specifically for the Electrolux EFLW427UIW series. These washers are manufactured by Electrolux under the Frigidaire parts system. Confirm your model number matches before ordering, or contact us with your model and we'll verify compatibility.
Key Features
- Genuine OEM Frigidaire water inlet valve assembly — factory-original part
- Integrated flow meter included — measures water volume entering the tub
- Direct replacement for superseded part number 5304514791
- Solenoid-operated valve controls water flow from household supply lines
- Designed for Electrolux 27" front-load washers (EFLW427UIW series)
- Install time approximately 15–30 minutes with basic screwdrivers
Product Specifications
| Part Number |
5304522535 |
| OEM Part Number |
5304522535 |
| Replaces Part Number |
5304514791 |
| Part Type |
Washer Water Inlet Valve Assembly |
| Includes |
Integrated Flow Meter |
| Condition |
New |
| Brand |
Frigidaire |
| Compatible Brand |
Electrolux / Frigidaire |
| Appliance Type |
Front Load Washer |
| Voltage |
120V |
Safety Warning
Unplug the washer and turn off both hot and cold water supply valves before starting this repair. Have towels ready — residual water will drain from the hoses when disconnected. The valve sits at the back of the washer behind the top or rear access panel. Disconnect the water supply hoses from the old valve, unplug the wire harness connectors from each solenoid coil, and remove the mounting screws. Install the new 5304522535 valve in the same orientation, reconnect the wire harnesses to the matching solenoid terminals, and reattach the water supply hoses. Hand-tighten the hose connections first, then snug with pliers — do not overtighten or you may crack the plastic inlet ports. Turn the water back on and check for leaks at every connection before plugging the washer in and running a test cycle.
Frequently Asked Questions
My washer fills slowly — is this the right part?
It depends on the cause. First check that both water supply valves behind the washer are fully open and that the inlet hose screens are not clogged with sediment. If the water pressure is fine and the screens are clean, a failing inlet valve is the next most likely cause of slow fill on these Electrolux models.
What does the integrated flow meter do?
The flow meter is a small turbine sensor built into the valve assembly. As water passes through the valve, the turbine spins and generates pulses that the control board counts to measure the exact volume of water entering the tub. This is how the washer determines when the correct fill level has been reached for each cycle and load size.
What is the difference between 5304522535 and 5304514791?
The 5304514791 is the earlier version of this valve assembly. Frigidaire superseded it with 5304522535, which is the current replacement. If you order 5304514791 from Frigidaire today, you will receive the 5304522535 since it is the updated part number for the same valve.
My washer keeps filling after I unplug it — what does that mean?
If water continues flowing into the tub after the washer is unplugged, the valve's solenoid plunger is physically stuck in the open position. This is a definitive sign that the inlet valve has failed mechanically and must be replaced. Turn off the water supply valves immediately to stop the flow.
Is this compatible with other Electrolux or Frigidaire washer models?
This valve assembly is currently listed only for the Electrolux EFLW427UIW series (suffix 0, 1, and 2). Other Electrolux and Frigidaire front-load washers use different valve assemblies with different flow meter configurations. Do not substitute this valve on a model it is not listed for — the solenoid coil count, hose port arrangement, and flow meter type may differ.
Genuine OEM Part
Fast Shipping
In Stock
Easy Install
