W10440729 Washer Genuine OEM Suspension Rod Support Kit

Description

W10440729 Washer Suspension Rod Support Kit — Genuine OEM

The W10440729 is a genuine OEM suspension rod support kit for Whirlpool-built top-load washers. Inside the cabinet, four suspension rods hang from the top of the frame and connect to the outer tub through ball-and-cup joints. Each rod passes through a plastic cup at the top and seats into a ball bushing at the tub bracket. Together, these eight pieces — four cups and four bushings — allow the tub to move freely during agitation while absorbing the momentum of an unbalanced spin cycle. When the cups or bushings crack, flatten, or wear smooth, they lose the ability to dampen tub movement, and the washer begins to shake, walk, or bang during spin.

The W10440729 kit includes all eight support pieces: four suspension ball cups and four suspension ball bushings. The cups and bushings are made of plastic and wear gradually under the repeated stress of spin cycles. A washer that has been in service for several years will often develop a progressive vibration problem as these supports lose their shape. Because all four rod positions share the same load, it is standard practice to replace all eight pieces at once rather than isolating a single worn cup — the remaining supports are typically close behind.

QUICK ANSWER

Will This Fix Your Washer?

If your top-load washer shakes violently during spin, walks across the floor, or makes a loud banging noise when the drum shifts direction, worn suspension rod supports are one of the most common causes. The W10440729 replaces all four cup-and-bushing sets at once. After installation, run the washer's recalibration cycle so the control board relearns the tub's balance profile with the new supports in place.

Common Symptoms

  • Washer shakes or vibrates excessively during spin cycle
  • Washer walks or moves across the floor while running
  • Loud banging or thumping noise during spin
  • Tub rocks visibly when the drum changes direction
  • Vibration has gotten progressively worse over time

Cross Reference Information

The W10440729 replaces the following earlier part numbers and distributor catalog numbers. If any of these appear in a parts lookup for your washer model, the W10440729 is the current replacement.

W10440729, 2118951, W10215136, W10256551, W10316397, W10405423, W10560146, AH3502189, AP5306956, AWP40782, EAP3502189, EA3502189, PD00006079, PS3502189
COMPATIBILITY

This genuine OEM kit fits Whirlpool-built top-load washers sold under the Whirlpool, Maytag, Kenmore, Amana, Crosley, Admiral, Inglis, and Roper brand names. Confirm your model number before ordering.

Sample compatible models: WTW5000DW1, WTW4800XQ2, WTW5500XW2, WTW5700XW3, WTW4815EW1, MVWX600XW2, NTW4655EW1, 11021352112, 11026012012, 3DWTW4840YW0

Key Features

  • Genuine OEM Whirlpool suspension rod support kit
  • Includes 4 suspension ball cups and 4 suspension ball bushings (8 pieces)
  • Plastic construction — cups measure 1-13/16" diameter × ⅞" H
  • Dampens tub movement during agitation and spin cycles
  • Replaces all four rod support positions in one kit
  • Fits Whirlpool, Maytag, Kenmore, Amana, Crosley, Admiral, Inglis, and Roper washers

Specifications

Part Number W10440729
Condition New
Brand Whirlpool
Part Type Suspension Rod Support Kit
Appliance Type Washer
Kit Contents 4 suspension ball cups, 4 suspension ball bushings
Material Plastic
Color White (opaque cups / translucent bushings)
Compatible Brands Whirlpool, Maytag, Kenmore, Amana, Crosley, Admiral, Inglis, Roper
Supersedes W10405423, W10316397, W10256551, W10215136
Safety Warning
Unplug the washer and disconnect the water supply hoses before beginning this repair. Accessing the suspension rods requires lifting or tipping the washer cabinet, which is heavy. Use a second person or a prop to hold the cabinet in place while working. After installing the new supports, run the washer's recalibration cycle before using it — the control board needs to relearn the tub's balance profile with the new supports installed.

Frequently Asked Questions

What do the suspension rod cups and bushings actually do?
Each suspension rod hangs from the top of the washer frame and connects to the outer tub. The cup sits at the top of the rod where it passes through the frame, and the bushing sits at the tub bracket. Together they create a ball-and-socket joint that lets the tub swing freely during agitation while absorbing the inertia of unbalanced spin loads. When the plastic wears down or cracks, the rod loses its damping — the tub swings too far and slams against the cabinet.
Why replace all four sets instead of just the one that's worn?
All four rod positions share the same load every cycle, so they wear at roughly the same rate. If one cup is cracked or flattened, the other three are close behind. Replacing only one leaves three weak points that will fail soon, and the uneven damping can actually make the vibration worse by letting the tub tilt during spin. The W10440729 includes all eight pieces for this reason.
How can I tell if the cups are worn without disassembling the washer?
Open the lid and push down firmly on one side of the wash tub. Release it and watch how it rebounds. A tub with good supports will bounce once or twice and settle. A tub with worn supports will continue rocking or will not return to center. You can also listen — if you hear a hollow clunking when you push the tub, a cup has likely cracked and the rod is rattling in its socket.
Do I need to recalibrate the washer after replacing the supports?
Yes. Most Whirlpool-built top-load washers with electronic controls require a recalibration cycle after any suspension work. The control board uses a stored balance profile to manage spin speed — if the profile does not match the new supports, the washer may still vibrate or throw an off-balance error. The recalibration procedure is in the technician's manual, which is usually taped inside the cabinet or behind the control panel.
Is this the same as a suspension rod kit?
No. The W10440729 is the support kit — it contains only the cups and bushings that sit on the rods. The rods themselves are a separate part, sold as a suspension rod kit under a different part number. If your rods are bent, rusted, or the springs are stretched, you need the rod kit in addition to this support kit. If the rods are straight and the springs are intact, the W10440729 support kit alone is typically all you need.
Genuine OEM Part Fast Shipping In Stock 1–2 Hour Install
Product form

W10440729 Washer Genuine OEM Suspension Rod Support Kit

Free Pickup in In Stock Parts-O-Matic - WB Store 1820 Featherstone Road Woodbridge, VA 22191 Usually ready in 1 hour
Online Shipped Price $16.00 List Price $13.50You Save: $2.50Delivered to your address
Store Walk-In
Discounted Price
$6.83Walk-In Savings: $6.67In-store purchase only — not valid for online checkout
✓ IN STOCK
Ships Today if ordered within --:--:--
Free Pickup in our Store • Usually ready in 1 hour
  • Shipped today? Order within: Nov 21, 2026 14:00:00 -0500

Description

W10440729 Washer Suspension Rod Support Kit — Genuine OEM

The W10440729 is a genuine OEM suspension rod support kit for Whirlpool-built top-load washers. Inside the cabinet, four suspension rods hang from the top of the frame and connect to the outer tub through ball-and-cup joints. Each rod passes through a plastic cup at the top and seats into a ball bushing at the tub bracket. Together, these eight pieces — four cups and four bushings — allow the tub to move freely during agitation while absorbing the momentum of an unbalanced spin cycle. When the cups or bushings crack, flatten, or wear smooth, they lose the ability to dampen tub movement, and the washer begins to shake, walk, or bang during spin.

The W10440729 kit includes all eight support pieces: four suspension ball cups and four suspension ball bushings. The cups and bushings are made of plastic and wear gradually under the repeated stress of spin cycles. A washer that has been in service for several years will often develop a progressive vibration problem as these supports lose their shape. Because all four rod positions share the same load, it is standard practice to replace all eight pieces at once rather than isolating a single worn cup — the remaining supports are typically close behind.

QUICK ANSWER

Will This Fix Your Washer?

If your top-load washer shakes violently during spin, walks across the floor, or makes a loud banging noise when the drum shifts direction, worn suspension rod supports are one of the most common causes. The W10440729 replaces all four cup-and-bushing sets at once. After installation, run the washer's recalibration cycle so the control board relearns the tub's balance profile with the new supports in place.

Common Symptoms

  • Washer shakes or vibrates excessively during spin cycle
  • Washer walks or moves across the floor while running
  • Loud banging or thumping noise during spin
  • Tub rocks visibly when the drum changes direction
  • Vibration has gotten progressively worse over time

Cross Reference Information

The W10440729 replaces the following earlier part numbers and distributor catalog numbers. If any of these appear in a parts lookup for your washer model, the W10440729 is the current replacement.

W10440729, 2118951, W10215136, W10256551, W10316397, W10405423, W10560146, AH3502189, AP5306956, AWP40782, EAP3502189, EA3502189, PD00006079, PS3502189
COMPATIBILITY

This genuine OEM kit fits Whirlpool-built top-load washers sold under the Whirlpool, Maytag, Kenmore, Amana, Crosley, Admiral, Inglis, and Roper brand names. Confirm your model number before ordering.

Sample compatible models: WTW5000DW1, WTW4800XQ2, WTW5500XW2, WTW5700XW3, WTW4815EW1, MVWX600XW2, NTW4655EW1, 11021352112, 11026012012, 3DWTW4840YW0

Key Features

  • Genuine OEM Whirlpool suspension rod support kit
  • Includes 4 suspension ball cups and 4 suspension ball bushings (8 pieces)
  • Plastic construction — cups measure 1-13/16" diameter × ⅞" H
  • Dampens tub movement during agitation and spin cycles
  • Replaces all four rod support positions in one kit
  • Fits Whirlpool, Maytag, Kenmore, Amana, Crosley, Admiral, Inglis, and Roper washers

Specifications

Part Number W10440729
Condition New
Brand Whirlpool
Part Type Suspension Rod Support Kit
Appliance Type Washer
Kit Contents 4 suspension ball cups, 4 suspension ball bushings
Material Plastic
Color White (opaque cups / translucent bushings)
Compatible Brands Whirlpool, Maytag, Kenmore, Amana, Crosley, Admiral, Inglis, Roper
Supersedes W10405423, W10316397, W10256551, W10215136
Safety Warning
Unplug the washer and disconnect the water supply hoses before beginning this repair. Accessing the suspension rods requires lifting or tipping the washer cabinet, which is heavy. Use a second person or a prop to hold the cabinet in place while working. After installing the new supports, run the washer's recalibration cycle before using it — the control board needs to relearn the tub's balance profile with the new supports installed.

Frequently Asked Questions

What do the suspension rod cups and bushings actually do?
Each suspension rod hangs from the top of the washer frame and connects to the outer tub. The cup sits at the top of the rod where it passes through the frame, and the bushing sits at the tub bracket. Together they create a ball-and-socket joint that lets the tub swing freely during agitation while absorbing the inertia of unbalanced spin loads. When the plastic wears down or cracks, the rod loses its damping — the tub swings too far and slams against the cabinet.
Why replace all four sets instead of just the one that's worn?
All four rod positions share the same load every cycle, so they wear at roughly the same rate. If one cup is cracked or flattened, the other three are close behind. Replacing only one leaves three weak points that will fail soon, and the uneven damping can actually make the vibration worse by letting the tub tilt during spin. The W10440729 includes all eight pieces for this reason.
How can I tell if the cups are worn without disassembling the washer?
Open the lid and push down firmly on one side of the wash tub. Release it and watch how it rebounds. A tub with good supports will bounce once or twice and settle. A tub with worn supports will continue rocking or will not return to center. You can also listen — if you hear a hollow clunking when you push the tub, a cup has likely cracked and the rod is rattling in its socket.
Do I need to recalibrate the washer after replacing the supports?
Yes. Most Whirlpool-built top-load washers with electronic controls require a recalibration cycle after any suspension work. The control board uses a stored balance profile to manage spin speed — if the profile does not match the new supports, the washer may still vibrate or throw an off-balance error. The recalibration procedure is in the technician's manual, which is usually taped inside the cabinet or behind the control panel.
Is this the same as a suspension rod kit?
No. The W10440729 is the support kit — it contains only the cups and bushings that sit on the rods. The rods themselves are a separate part, sold as a suspension rod kit under a different part number. If your rods are bent, rusted, or the springs are stretched, you need the rod kit in addition to this support kit. If the rods are straight and the springs are intact, the W10440729 support kit alone is typically all you need.
Genuine OEM Part Fast Shipping In Stock 1–2 Hour Install
W10440729, 2118951, W10215136, W10256551, W10316397, W10405423, W10560146, AH3502189, AP5306956, AWP40782, EAP3502189, EA3502189, PD00006079, PS3502189

Recently viewed products

© 2026 Parts-O-Matic,

    • Amazon
    • American Express
    • Apple Pay
    • Diners Club
    • Discover
    • Google Pay
    • Mastercard
    • PayPal
    • Shop Pay
    • USDC
    • Visa

    Login

    Forgot your password?

    Don't have an account yet?
    Create account

    Need Help? Call Us Now +1 (855) 200-8978 CONTACT US
    W10440729 Washer Genuine OEM Suspension Rod Support Kit
    W10440729 Washer Genuine OEM Suspension Rod Support Kit
    $16.00 $13.50