W11168743 Genuine OEM Whirlpool Washer Hot Water Inlet Valve
The W11168743 is a genuine Whirlpool OEM hot water inlet valve for Whirlpool top-load washers. This is a single-solenoid valve dedicated specifically to hot water, with a standard hose fitting inlet and one water outlet. When the wash cycle calls for hot water, the valve's solenoid opens to admit it from your home's hot water supply line; once the correct fill level is reached, it closes again.
Rated 120V, 60Hz. Common causes of failure include wear and tear over time, clogging from mineral deposits or sediment in the water supply, and electrical faults that prevent the valve from opening or closing properly. A failing hot water valve typically shows up as the washer not filling properly or not filling at all, slow or irregular water flow even when the inlet screens are clear of obstruction, no hot water reaching the tub, or water dripping inside the tub when the washer isn't running. It directly replaces AP6327638, WPW10240948, W10240948, 4585634, PS12348074, W10921515, and 33390068.
Quick Answer
The W11168743 Genuine OEM Whirlpool Washer Hot Water Inlet Valve fixes Whirlpool top-load washers (and select Maytag, KitchenAid, Jenn-Air, Amana, Roper, and Kenmore washers) that won't fill, fill slowly, have no hot water reaching the tub, or leak water inside the drum when not running. 1-solenoid, 1-inlet, 1-outlet hot water valve. 120V, 60Hz. Replaces AP6327638, WPW10240948, W10240948, 4585634, PS12348074, W10921515, 33390068. This is the hot valve — the matching cold valve for the same platform is a separate part, W11168740.
Common Problems This Part Fixes
- Washer not filling properly, or not filling at all
- Water flow slow or irregular even when inlet screens are clear
- No hot water reaching the tub during the wash cycle
- Water dripping or leaking inside the tub when the washer isn't running
- Washer not washing properly due to insufficient hot water
- Washer that won't start because it's stuck waiting for water
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This washer hot water inlet valve directly replaces the following OEM and cross-reference part numbers:
W11168743, 1873019, 33390068, 4585634, W10240948, W10921515, WPW10240948, AP6017592, AP6327638, EAP11750891, EAP12348074, PS11750891, AWP43142, OEM18982923, PD00040928, PS12348074.
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This hot water inlet valve is compatible with select Whirlpool top-load washers, and also fits select Maytag, KitchenAid, Jenn-Air, Amana, Roper, Admiral, Hardwick, Estate, Magic Chef, Crosley, Inglis, Norge, Modern Maid, Caloric, Kenmore, and Ikea washers built on the Whirlpool platform.
Note — hot valve, not cold: This is the hot water valve. The matching cold water valve for the same Whirlpool top-load platform is a separate part, W11168740 (blue body, 2-solenoid). The two are not interchangeable, so replace the correct one for the symptom you're seeing — or both if you're unsure which is causing the issue. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure.
Key Features
- Genuine Whirlpool OEM part — factory-specified solenoid design and flow-rate calibration
- Dedicated hot water valve — standard hose fitting inlet, single water outlet
- Resolves "won't fill," "fills slowly," "no hot water," and "leaking inside the tub" symptoms caused by valve failure
- Rated 120V, 60Hz
- Direct drop-in replacement — matches the original mounting and hose connections
- Replaces AP6327638, WPW10240948, W10240948, 4585634, PS12348074, W10921515, and 33390068
- Compatible with Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Roper, and Kenmore top-load washers
- Genuine OEM replacement — guaranteed fit, materials, and performance
Product Specifications
| Part Number |
W11168743 |
| Part Type |
Washer Hot Water Inlet Valve |
| Condition |
Genuine OEM |
| Brand |
Whirlpool |
| Application |
Top-Load Washers |
| Voltage |
120V |
| Frequency |
60 Hz |
| Solenoids |
1 |
| Inlets |
1 (standard hose fitting) |
| Outlets |
1 |
| Companion Part |
W11168740 (cold water valve, 2-solenoid, sold separately) |
| Quantity |
1 valve |
| Compatible Brands |
Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Roper, Admiral, Hardwick, Estate, Magic Chef, Crosley, Inglis, Norge, Modern Maid, Caloric, Kenmore, Ikea |
Installation Notes
⚠️ Shut Off Water Supply And Unplug Washer Before Starting Disconnect power at the outlet or shut off the circuit breaker, and shut off the hot water supply valve before beginning. Wear work gloves. Access is typically from the rear of the washer: remove the screws securing the top or rear panel to reach the valve. Have a towel handy for residual water when you disconnect the supply hose. Photograph the wiring and hose connections before disconnecting anything. Disconnect the hot water supply hose, disconnect the electrical connector, and remove the mounting screws holding the valve in place, then pull it free. Install the new W11168743 in the same position, secure the mounting screws, and reconnect the electrical connector fully. Reattach the hot water supply hose, tightening securely by hand plus a partial turn with pliers — avoid overtightening plastic threaded fittings. While you're in there, it's also worth checking the hoses that run from the valve into the detergent dispenser drawer, since a loose or damaged hose at that connection can produce similar fill or leak symptoms. Restore the water supply and check for leaks before restoring power. Run a test cycle to confirm the washer fills normally with hot water. Tools needed: Phillips screwdriver, pliers, towel, work gloves.
Frequently Asked Questions
How do I know if it's the hot valve or the cold valve that's failed?
Pay attention to which water temperature is affected. If the washer isn't getting hot water but cold-water fills work fine, this hot valve (W11168743) is the likely cause. If the opposite is true, the cold valve (W11168740) is more likely the issue. If both hot and cold fills are affected, or you're not sure, it's worth checking both valves before ordering.
I have water dripping inside the tub when the washer isn't running. Is this the valve?
Yes, likely one of the two inlet valves. A worn internal seal can let water seep through even when the valve should be fully closed, causing exactly this symptom. Since there are two valves (hot and cold) on this platform, you may need to inspect both to determine which one is leaking, or replace both if you're unable to isolate it.
The valve and hoses look fine but water flow is still irregular. What else should I check?
If the inlet screens are clear of obstruction and water flow is still weak or inconsistent, it's worth checking the hoses that run from the valve into the detergent dispenser drawer, since a kink, clog, or loose connection there can produce similar symptoms to a failing valve. Household water pressure and any inline filter screens are also worth ruling out.
Is this an OEM or aftermarket part?
This is a genuine OEM part, manufactured by Whirlpool to factory specifications — guaranteed fit, materials, and performance. It matches the original solenoid design, flow rate, and hose connection configuration of the hot water inlet valve originally installed in your washer.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
