WB24X47193 Range Genuine OEM Triple Burner Infinite Switch

Description

Genuine OEM WB24X47193 Range Triple Burner Infinite Switch

An infinite switch is the dial-controlled regulator behind every electric range knob — it cycles power on and off rapidly at varying intervals to hold the element at the temperature you select. The WB24X47193 is the GE genuine OEM infinite switch specifically designed for the triple burner (also called a haliant element), the large surface element with three concentric heating rings that let you match the heated area to your pot size. Inside the switch, a bimetal strip heats up alongside the element circuit; as it warps, it physically breaks and re-makes the electrical contact, creating the on-off cycling that maintains your chosen heat level.

When this switch fails, the bimetal strip either stays permanently closed — locking the burner on high with no way to reduce heat — or opens permanently and the burner won't heat at all. Because the triple burner routes all three rings through a single infinite switch, a failed switch can knock out the entire element even though the rings themselves are fine. This is a genuine GE part with the correct electrical ratings and terminal configuration for direct replacement, and typical installation behind the control panel takes about 15–30 minutes.

Quick Answer

Will This Fix My Range?

The Genuine OEM WB24X47193 Infinite Switch is the replacement for GE electric ranges and cooktops where the triple burner won't heat, is stuck on high, or won't adjust temperature. It supersedes the earlier WB24X25152. Classic symptoms: burner stuck on high and won't simmer, one or more rings of the triple element won't heat, or the hot surface indicator stays on after the knob is turned off.

Common Symptoms

  • Triple burner stuck on high heat — won't reduce when turned down
  • Burner won't heat at all when the knob is turned on
  • Outer ring works but inner rings don't respond
  • Burner turns on briefly then shuts off after a few seconds
  • Hot surface indicator light stays on after burner is switched off
  • Burner heats erratically or cycles at the wrong temperature

Replaces Part Numbers

Part numbers change over a product's lifecycle as manufacturers update designs. These are the known superseded, alternate, and cross-reference numbers for this switch:

WB24X47193 replaces WB24X25152, 191D8398P005, MHSA-W779-GEM, AGE1176033, AP7216143, EAP11773823, FIX11773823, PS11773823

If your old switch or parts diagram shows any of these numbers, this is the correct replacement.

Compatibility

This infinite switch is listed for select GE, Hotpoint, Monogram, Café, and Haier electric ranges and cooktops with a triple burner element, including:

  • GE JB750, JB755, JS750 series electric ranges
  • GE PB930, PB935, PB960, PB965, PB980 series electric ranges
  • GE PCB980 series electric ranges
  • GE PCS968 series slide-in electric ranges
  • Select Café and Monogram built-in electric cooktops

Note: The model list above is a sample. This switch fits many more GE-family range and cooktop models with a triple (3-ring) haliant surface element. Always confirm compatibility against your model number before ordering, or contact our support team for verification.

Key Features

  • Genuine OEM GE infinite switch control — not an aftermarket part
  • Designed specifically for triple burner (3-ring haliant) surface elements
  • Restores smooth heat adjustment from low simmer to full high
  • Correct electrical ratings and terminal configuration for direct replacement
  • Supersedes earlier part number WB24X25152
  • Typical installation takes 15–30 minutes with basic hand tools

Product Specifications

Part Number WB24X47193
Supersedes WB24X25152
Part Type Infinite Switch Control
Condition Genuine OEM
Brand GE
Controls Triple Burner (3-Ring Haliant Element)
Compatible Brands GE, Hotpoint, Monogram, Café, Haier
Appliance Type Electric Range / Cooktop
Install Time 15–30 minutes
Safety Warning Disconnect the range from power at the circuit breaker before starting any repair — electric ranges operate on 240V, which can cause serious injury or death. The infinite switch is located behind the control panel. Remove the back panel screws or the rear access cover to reach the switch mounting. Note the wire positions before disconnecting — a phone photo is the easiest reference. The switch connects to the element circuit with push-on spade terminals. Pull terminals straight off; do not twist or pry sideways. Seat the new switch in the mounting bracket, reconnect the wires to the same terminals, reassemble the panel, restore power, and test all three rings of the triple burner at low, medium, and high settings.

Frequently Asked Questions

How does an infinite switch actually control temperature?

Inside the switch, a small bimetal strip sits in a heater circuit that runs parallel to the element circuit. When you turn the knob, you adjust the gap between the bimetal strip and the electrical contact. The strip heats up, warps, and breaks the contact — cutting power to the element — then cools, straightens, and re-makes contact. This on-off cycling happens continuously, and the ratio of on-time to off-time determines the heat level. At "High," the contact stays closed nearly all the time. At "Low," it's open far more than it's closed.

My burner is stuck on high. Is it the switch or the element?

A burner stuck on high is almost always the infinite switch, not the element. When the bimetal strip inside the switch fails in the closed position, it sends continuous power to the element with no cycling. The element itself has no way to "stick on" — it simply converts whatever power it receives into heat. If the burner won't reduce from high regardless of knob position, replacing the infinite switch is the correct repair.

The outer ring of my triple burner works but the inner rings don't. Is this one switch?

Yes — all three rings of a triple burner are controlled by a single infinite switch. However, the individual rings within the element have separate heating circuits. If only some rings heat, the problem could be the element itself (a broken internal circuit in one ring) rather than the switch. You can test the switch with a multimeter: turn the knob to High and check for continuity across the switch terminals. If the switch shows continuity but a ring won't heat, the element is the likely cause.

What is the difference between WB24X47193 and WB24X25152?

WB24X25152 is the earlier part number that has been superseded by WB24X47193. GE periodically updates part numbers when they make manufacturing changes. The WB24X47193 is the current replacement — it fits the same models and mounts the same way. If your parts diagram shows WB24X25152, order WB24X47193.

Can I test my infinite switch before replacing it?

Yes. Disconnect power at the breaker, remove the back panel to access the switch, and use a multimeter set to continuity or resistance. With the knob turned to High, you should read near-zero ohms (closed circuit) across the load terminals. With the knob on Off, you should read infinite resistance (open circuit). If the switch reads open at High or closed at Off, it has failed and needs replacement. Always test with power disconnected.

Genuine OEM Part Fast Shipping In Stock 15–30 Min Install
Product form

WB24X47193 Range Genuine OEM Triple Burner Infinite Switch

Online Shipped Price $98.00 List Price $69.80You Save: $28.20Delivered to your address
Store Walk-In
Discounted Price $57.23Walk-In Savings: $12.57In-store purchase only — not valid for online checkout
  •  This product will be available for pickup at a designated location within 3–4 business days after checkout.
✓ IN STOCK
Ships Today if ordered within --:--:--
🔍 CHECK YOUR MODEL COMPATIBILITY

Enter your appliance model number to check compatibility.

View Full Compatibility List ↓

Description

Genuine OEM WB24X47193 Range Triple Burner Infinite Switch

An infinite switch is the dial-controlled regulator behind every electric range knob — it cycles power on and off rapidly at varying intervals to hold the element at the temperature you select. The WB24X47193 is the GE genuine OEM infinite switch specifically designed for the triple burner (also called a haliant element), the large surface element with three concentric heating rings that let you match the heated area to your pot size. Inside the switch, a bimetal strip heats up alongside the element circuit; as it warps, it physically breaks and re-makes the electrical contact, creating the on-off cycling that maintains your chosen heat level.

When this switch fails, the bimetal strip either stays permanently closed — locking the burner on high with no way to reduce heat — or opens permanently and the burner won't heat at all. Because the triple burner routes all three rings through a single infinite switch, a failed switch can knock out the entire element even though the rings themselves are fine. This is a genuine GE part with the correct electrical ratings and terminal configuration for direct replacement, and typical installation behind the control panel takes about 15–30 minutes.

Quick Answer

Will This Fix My Range?

The Genuine OEM WB24X47193 Infinite Switch is the replacement for GE electric ranges and cooktops where the triple burner won't heat, is stuck on high, or won't adjust temperature. It supersedes the earlier WB24X25152. Classic symptoms: burner stuck on high and won't simmer, one or more rings of the triple element won't heat, or the hot surface indicator stays on after the knob is turned off.

Common Symptoms

  • Triple burner stuck on high heat — won't reduce when turned down
  • Burner won't heat at all when the knob is turned on
  • Outer ring works but inner rings don't respond
  • Burner turns on briefly then shuts off after a few seconds
  • Hot surface indicator light stays on after burner is switched off
  • Burner heats erratically or cycles at the wrong temperature

Replaces Part Numbers

Part numbers change over a product's lifecycle as manufacturers update designs. These are the known superseded, alternate, and cross-reference numbers for this switch:

WB24X47193 replaces WB24X25152, 191D8398P005, MHSA-W779-GEM, AGE1176033, AP7216143, EAP11773823, FIX11773823, PS11773823

If your old switch or parts diagram shows any of these numbers, this is the correct replacement.

Compatibility

This infinite switch is listed for select GE, Hotpoint, Monogram, Café, and Haier electric ranges and cooktops with a triple burner element, including:

  • GE JB750, JB755, JS750 series electric ranges
  • GE PB930, PB935, PB960, PB965, PB980 series electric ranges
  • GE PCB980 series electric ranges
  • GE PCS968 series slide-in electric ranges
  • Select Café and Monogram built-in electric cooktops

Note: The model list above is a sample. This switch fits many more GE-family range and cooktop models with a triple (3-ring) haliant surface element. Always confirm compatibility against your model number before ordering, or contact our support team for verification.

Key Features

  • Genuine OEM GE infinite switch control — not an aftermarket part
  • Designed specifically for triple burner (3-ring haliant) surface elements
  • Restores smooth heat adjustment from low simmer to full high
  • Correct electrical ratings and terminal configuration for direct replacement
  • Supersedes earlier part number WB24X25152
  • Typical installation takes 15–30 minutes with basic hand tools

Product Specifications

Part Number WB24X47193
Supersedes WB24X25152
Part Type Infinite Switch Control
Condition Genuine OEM
Brand GE
Controls Triple Burner (3-Ring Haliant Element)
Compatible Brands GE, Hotpoint, Monogram, Café, Haier
Appliance Type Electric Range / Cooktop
Install Time 15–30 minutes
Safety Warning Disconnect the range from power at the circuit breaker before starting any repair — electric ranges operate on 240V, which can cause serious injury or death. The infinite switch is located behind the control panel. Remove the back panel screws or the rear access cover to reach the switch mounting. Note the wire positions before disconnecting — a phone photo is the easiest reference. The switch connects to the element circuit with push-on spade terminals. Pull terminals straight off; do not twist or pry sideways. Seat the new switch in the mounting bracket, reconnect the wires to the same terminals, reassemble the panel, restore power, and test all three rings of the triple burner at low, medium, and high settings.

Frequently Asked Questions

How does an infinite switch actually control temperature?

Inside the switch, a small bimetal strip sits in a heater circuit that runs parallel to the element circuit. When you turn the knob, you adjust the gap between the bimetal strip and the electrical contact. The strip heats up, warps, and breaks the contact — cutting power to the element — then cools, straightens, and re-makes contact. This on-off cycling happens continuously, and the ratio of on-time to off-time determines the heat level. At "High," the contact stays closed nearly all the time. At "Low," it's open far more than it's closed.

My burner is stuck on high. Is it the switch or the element?

A burner stuck on high is almost always the infinite switch, not the element. When the bimetal strip inside the switch fails in the closed position, it sends continuous power to the element with no cycling. The element itself has no way to "stick on" — it simply converts whatever power it receives into heat. If the burner won't reduce from high regardless of knob position, replacing the infinite switch is the correct repair.

The outer ring of my triple burner works but the inner rings don't. Is this one switch?

Yes — all three rings of a triple burner are controlled by a single infinite switch. However, the individual rings within the element have separate heating circuits. If only some rings heat, the problem could be the element itself (a broken internal circuit in one ring) rather than the switch. You can test the switch with a multimeter: turn the knob to High and check for continuity across the switch terminals. If the switch shows continuity but a ring won't heat, the element is the likely cause.

What is the difference between WB24X47193 and WB24X25152?

WB24X25152 is the earlier part number that has been superseded by WB24X47193. GE periodically updates part numbers when they make manufacturing changes. The WB24X47193 is the current replacement — it fits the same models and mounts the same way. If your parts diagram shows WB24X25152, order WB24X47193.

Can I test my infinite switch before replacing it?

Yes. Disconnect power at the breaker, remove the back panel to access the switch, and use a multimeter set to continuity or resistance. With the knob turned to High, you should read near-zero ohms (closed circuit) across the load terminals. With the knob on Off, you should read infinite resistance (open circuit). If the switch reads open at High or closed at Off, it has failed and needs replacement. Always test with power disconnected.

Genuine OEM Part Fast Shipping In Stock 15–30 Min Install
WB24X47193, WB24X25152 191D8398P005, MHSA-W779-GEM, AGE1176033, AP7216143, EAP11773823, FIX11773823, OEM21648438, PS11773823

Model Compatibility

Search your appliance model number below. Supports partial or full model search.

🔍 CHECK YOUR MODEL COMPATIBILITY

Type your full or partial model number above to instantly check if this part fits your appliance.

✓ Guaranteed Fit — exact model match found.
No matching model found. Please verify your full model number or contact support.
Loading compatible models...
Model Number Manufacturer Appliance Type

⚠️ Note: This is a partial compatibility list. Always verify your appliance model number before ordering. Contact our support team if you’re unsure.

Recently viewed products

© 2026 Parts-O-Matic,

    • Amazon
    • American Express
    • Apple Pay
    • Diners Club
    • Discover
    • Google Pay
    • Mastercard
    • PayPal
    • Shop Pay
    • USDC
    • Visa

    Login

    Forgot your password?

    Don't have an account yet?
    Create account

    Need Help? Call Us Now +1 (855) 200-8978 CONTACT US
    WB24X47193 Range Genuine OEM Triple Burner Infinite Switch
    WB24X47193 Range Genuine OEM Triple Burner Infinite Switch
    $98.00 $69.80