WB44X200 Electric Range Lower Bake Element — Genuine OEM
The WB44X200 is a genuine OEM lower bake element for GE, Hotpoint, and RCA electric ranges and wall ovens. It sits at the bottom of the oven cavity and supplies the primary heat for baking. The element is a resistive heating coil encased in a stainless steel sheath — when the oven control sends 240 volts to the element, the internal coil converts electrical energy into heat at a rated output of 3,100 watts (240V) or 2,330 watts (208V). That heat radiates upward from the bottom of the cavity, which is why baking produces even, bottom-up heat that sets the structure of breads, cakes, and casseroles before the top surface browns.
Bake elements fail when the internal coil develops a hot spot — a point where the resistance is higher than the surrounding wire, causing that section to run hotter until the metal fatigues and breaks. When the coil breaks, the circuit opens and the element stops producing heat entirely. You will often see the failure point as a visible blister, burn-through hole, or crack in the outer sheath. In some cases the element arcs at the break point before it fails completely, producing a brief bright flash and a popping sound. Once the coil is broken, the element cannot be repaired — it must be replaced.
QUICK ANSWER
If your GE, Hotpoint, or RCA electric oven produces no heat on the Bake setting — or heats unevenly with a visible burn-through, blister, or crack on the lower element — the WB44X200 is the direct replacement. This genuine OEM element connects with screw-in terminals and installs in approximately 30 minutes with a Phillips screwdriver. Disconnect the circuit breaker before starting.
Common Symptoms
- Oven does not heat on the Bake setting
- Bake element has a visible hole, blister, or burn-through
- Oven heats unevenly — food is undercooked on the bottom
- Element sparked, arced, or made a popping sound before failing
- Bake element does not glow red when the oven is set to Bake
Cross Reference Information
The WB44X200 is GE's current part number for this lower bake element. It supersedes the earlier WB44X160 and WB44X0200 and is cross-referenced under the following distributor catalog numbers.
WB44X200 replaces TS44X200, WB44X0160, WB44X0200, WB44X160, WB44X200R, WB44X6200, AGE23663, AH249424, AP2031031, EA249424, EAP249424, PD00001067, PS249424
COMPATIBILITY
This genuine OEM bake element fits select GE, Hotpoint, RCA, and select Kenmore electric ranges and wall ovens. The element shape and terminal style must match your oven cavity — confirm your model number before ordering.
Compatible brands: GE, Hotpoint, RCA, Kenmore (select models)
Key Features
- Genuine OEM GE lower bake element — factory original, not aftermarket
- 3,100 watts at 240V / 2,330 watts at 208V — full rated heat output
- Stainless steel alloy sheath encasing a resistive heating coil
- Screw-in terminal connections — no wire nuts or crimp connectors needed
- Fits the lower position in the oven cavity for bottom-up bake heat
- Moderate installation — approximately 30 minutes with a Phillips screwdriver
Specifications
| Part Number |
WB44X200 |
| Condition |
New |
| Brand |
GE |
| Part Type |
Lower Bake Element |
| Appliance Type |
Electric Range / Wall Oven |
| Wattage |
3,100W (240V) / 2,330W (208V) |
| Voltage |
240V / 208V |
| Terminal Type |
Screw-in |
| Material |
Stainless Steel Alloy |
| Compatible Brands |
GE, Hotpoint, RCA, Kenmore |
| Supersedes |
WB44X160, WB44X0200 |
Safety Warning
Disconnect the oven from power at the circuit breaker before beginning any work — do not rely on turning the oven off at the control panel. Electric range bake elements carry 240 volts, which can cause serious injury or death. After turning off the breaker, verify power is off by attempting to turn on the oven light or clock display. When disconnecting the wire terminals from the old element, hold the wire firmly so it does not slip back through the rear oven wall — retrieving a dropped wire from behind the oven liner requires pulling the range away from the wall and removing the rear panel. Never turn on the oven with the element removed — exposed wires behind the oven liner can arc against the metal housing.
Frequently Asked Questions
How does a bake element fail and what does it look like?
Bake elements fail when the internal resistance coil develops a hot spot — a point of higher electrical resistance that overheats the surrounding sheath metal until it burns through. The failure appears as a blister, hole, or crack in the outer steel tube. Sometimes you will see a small bright spot or discoloration before it fails completely. Once the coil breaks at the hot spot, the electrical circuit opens and the element produces no heat at all. In some cases the element arcs briefly at the break point with a visible spark and a popping sound. The failure is permanent — the coil cannot be repaired.
My oven heats on Broil but not on Bake. Is the bake element the problem?
Most likely, yes. In a standard electric oven, the Bake setting powers only the lower element and the Broil setting powers only the upper element. If Broil works normally but Bake produces no heat, the lower bake element is the first thing to check. Inspect it visually for burn-through, blistering, or cracks. If it looks intact, you can test it with a multimeter set to ohms — a good 3,100-watt 240V element should read roughly 18 to 19 ohms. An open reading (infinite resistance) confirms the coil is broken even if the damage is not visible from outside the sheath.
What causes a bake element to burn out prematurely?
Food dripping onto the element is the most common accelerator. Sugary spills — fruit pie filling, cheese, or sauce — carbonize on the hot surface and create a spot where heat cannot radiate normally. That trapped heat concentrates on a small section of the coil, speeding up metal fatigue. Oven cleaner residue left on the element can cause the same localized heating. Using aluminum foil directly on the element to catch drips is another common cause — the foil reflects heat back into the sheath and can create hot spots. Normal thermal cycling over years of use will eventually fatigue the coil regardless, but keeping the element clean extends its life significantly.
What is the difference between 240V and 208V wattage ratings?
Residential homes in the United States are wired for 240 volts, which gives the element its full 3,100-watt output. Some apartments, condos, and commercial kitchens are wired for 208 volts — a configuration common in multi-unit buildings with three-phase power distribution. At 208V the same element draws less current and produces 2,330 watts. The element works on either voltage — it simply produces less heat at 208V, so the oven may take longer to reach the set temperature. You do not need a different element for 208V service.
How do I keep the wires from falling behind the oven wall during replacement?
When you remove the mounting screws and pull the old element forward, the wire terminals come with it through two holes in the rear oven liner. Before disconnecting the wires from the element terminals, take a photo of which wire goes where. Then, as you remove each wire from the old element's terminal screw, immediately bend a small hook or loop in the wire end, or clamp it with a small binder clip, so it cannot slide back through the hole. Some technicians tape the wires temporarily to the inside of the oven liner. If a wire does fall behind the liner, you will need to pull the range forward and remove the rear access panel to retrieve it.
Genuine OEM Part
Fast Shipping
In Stock
30-Minute Install