WD08X23476 Dishwasher Tub Gasket — Genuine OEM
The WD08X23476 is a genuine OEM tub gasket for GE dishwashers. This black plastic gasket sits in a channel around the perimeter of the dishwasher tub opening and presses against the inside face of the door when it closes. It creates the watertight seal that keeps wash water inside the tub during every fill, wash, and rinse cycle. The gasket is molded from a flexible plastic that conforms to the door surface under the compression of the door latch — not a rubber seal in the traditional sense, but a shaped plastic strip designed to channel any water that reaches the door edge back down into the tub rather than letting it escape onto the floor.
Over time the gasket material can harden, crack, or develop flat spots where it no longer makes full contact with the door panel. Food debris, mineral deposits, and detergent residue can also build up in the gasket channel and prevent it from seating properly. When the seal is compromised, water seeps past the gasket during the wash and rinse cycles and drips down the front of the tub onto the floor beneath the dishwasher. The leak is usually slow and may only appear during certain cycle phases when the spray arms are directing water toward the door.
QUICK ANSWER
Will This Fix Your Dishwasher?
If your GE or Hotpoint dishwasher leaks water from around the door during the wash cycle, the WD08X23476 tub gasket is the most common fix. This genuine OEM black plastic gasket presses into the channel around the tub opening and seals against the door when closed. No tools required — pull the old gasket out of its channel and press the new one in. Takes less than 15 minutes.
Common Symptoms
- Water leaking from the front of the dishwasher during wash or rinse cycles
- Puddles on the floor beneath or in front of the dishwasher
- Visible cracks, hardening, or deformation in the existing tub gasket
- Mineral or detergent buildup along the gasket channel preventing a proper seal
- Water dripping down the inside face of the door during operation
Cross Reference Information
The WD08X23476 is GE's current part number for this dishwasher tub gasket. It supersedes the earlier WD08X10088, WD08X20674, and WD08X22094 and is cross-referenced under the following distributor catalog numbers.
WD08X23476 replaces WD08X22094, WD08X10088, WD08X20674, 4466530, AGE24097, AP6041569, EAP11774412, FIX11774412, PS11774412
COMPATIBILITY
This genuine OEM tub gasket fits select GE, Hotpoint, and Crosley dishwashers. It is designed for GE's plastic-tub dishwasher platform. Confirm your model number before ordering.
Sample compatible models: GDF510PGJ4WW, GDF530PSM4SS, GDF535PGR1WW, GDF630PGM1WW, GDT625PGJ0BB, GDT625PSJ0SS, GDT655SSJ2SS, ADT521PGF6WS, GDF520PGJ2WW, GDT535PSJ0SS
Key Features
- Genuine OEM GE dishwasher tub gasket — factory original, not aftermarket
- Black flexible plastic construction — seals by compression against the door panel
- Presses into the channel around the tub opening — no adhesive or fasteners needed
- Creates a watertight seal that prevents leaks during wash and rinse cycles
- Made in the USA
- No tools required — pull old gasket out, press new gasket in
Specifications
| Part Number |
WD08X23476 |
| OEM Part Number |
WD08X23476 |
| Condition |
New |
| Brand |
GE |
| Part Type |
Dishwasher Tub Gasket |
| Appliance Type |
Dishwasher |
| Color |
Black |
| Material |
Plastic |
| Compatible Brands |
GE, Hotpoint, Crosley |
| Supersedes |
WD08X10088, WD08X20674, WD08X22094 |
Safety Warning
Turn off the dishwasher and cancel any active cycle before replacing the gasket. No electrical disconnection is necessary for this repair since you are only working on the door gasket channel and do not need to access any wiring or plumbing. Open the door fully to expose the tub opening. Pull the old gasket out of its channel starting at one corner — it lifts out by hand. Clean the channel of any debris, mineral buildup, or old detergent residue before installing the new gasket. Press the WD08X23476 into the channel starting at the top center and working around both sides to the bottom. Make sure the gasket is fully seated in the channel with no sections popped out or kinked. Close the door and run a short rinse cycle to verify the seal.
Frequently Asked Questions
How does the tub gasket create a seal?
The gasket sits in a molded channel that runs around the entire perimeter of the dishwasher tub opening. When the door closes and the latch engages, the door panel compresses the gasket into the channel. This compression creates a continuous seal that prevents wash water from escaping between the tub rim and the door. The gasket is shaped so that any water reaching the door edge is directed downward back into the tub rather than outward onto the floor.
Why is the gasket made of plastic instead of rubber?
GE uses a flexible plastic for this gasket because it holds its shape better than rubber over the life of the dishwasher. Rubber gaskets can swell, shrink, or degrade when exposed to hot water, detergent chemicals, and rinse aid over thousands of cycles. The plastic material resists chemical breakdown and maintains a consistent seal profile. It is flexible enough to compress against the door but rigid enough to stay seated in the channel without sagging or pulling out of position.
What causes the tub gasket to fail?
The most common cause is age and heat cycling. After years of exposure to hot wash water followed by cool-down periods, the plastic gradually loses flexibility and develops hard spots or hairline cracks. Mineral deposits from hard water and detergent residue can also build up in the gasket channel, pushing the gasket out of its seat and creating gaps. Physical damage from loading or unloading dishes — catching the gasket with a pot handle or rack edge — can tear or deform the seal at a single point, which is enough to cause a leak.
Can I clean the old gasket instead of replacing it?
If the gasket is not cracked, torn, or permanently deformed, cleaning it and the channel may stop the leak temporarily. Remove the gasket, soak it in warm water with white vinegar to dissolve mineral deposits, and scrub the channel clean. Reinstall and test. However, if the plastic has hardened or lost its flexibility — press it with your thumb and see if it springs back — cleaning will not restore the seal and replacement is the correct fix.
Is WD08X23476 the same gasket as WD08X23477?
No. The WD08X23476 fits GE dishwashers with plastic tubs. The WD08X23477 is a different gasket designed for GE dishwashers with stainless steel tubs. The two gaskets have different profiles to match their respective tub materials and rim shapes. Check your model number to determine which tub type your dishwasher has before ordering — installing the wrong gasket can result in a poor seal and continued leaking.
Genuine OEM Part
Fast Shipping
In Stock
No Tools Required