WD19X24829 Genuine OEM GE Dishwasher Drain Pump Kit
The WD19X24829 is a Genuine OEM GE replacement dishwasher drain pump kit compatible with select GE, GE Café, GE Monogram, Hotpoint, Haier, and Kenmore dishwashers. The drain pump removes wastewater from the dishwasher tub during the drain portion of each wash and rinse cycle. Without a properly functioning drain pump, water cannot be expelled from the tub — leaving standing water after a cycle, preventing the dishwasher from advancing to the next phase, or causing slow drainage that affects wash and dry performance.
As a Genuine OEM part manufactured by GE to factory specifications, the WD19X24829 is the current production drain pump kit that supersedes the earlier WD19X24394. Note: replacing this pump requires pulling the dishwasher out from under the counter to access the pump on the underside of the appliance — the pump is not accessible from inside the tub. It directly replaces WD19X24394, AP6802078, 4863016, PS12582714, and EAP12582714. Installs in 30–45 minutes with basic hand tools.
Quick Answer
The WD19X24829 Genuine OEM GE Dishwasher Drain Pump Kit fixes GE dishwashers that won't drain, leave standing water in the tub, make unusual noise during draining, or stop mid-cycle due to a drain fault. Genuine OEM — supersedes WD19X24394. Note: dishwasher must be pulled out from the cabinet to access the pump from the underside. Replaces WD19X24394, AP6802078, 4863016, PS12582714, EAP12582714. Compatible with GE, GE Café, GE Monogram, Hotpoint, Haier, and Kenmore dishwashers.
Common Problems This Part Fixes
- Dishwasher not draining — standing water remaining in the tub after a cycle
- Dishwasher draining very slowly — pump motor weakening below rated performance
- Dishwasher stopping mid-cycle — pump fault detected by control board
- Loud humming or buzzing during the drain phase — motor running but pump not expelling water
- Grinding or rattling during drain — damaged pump impeller or worn motor bearings
- Dishes not drying properly — standing water remaining in the tub affecting drying performance
- Water leaking from the bottom of the dishwasher near the pump area
Replaces Part Numbers
This drain pump kit directly replaces the following OEM and cross-reference part numbers:
WD19X24394, 4863016, AGE24616, AP6802078, EAP12582714, PD00050849, PS12582714.
WD19X24829 is the current production part number superseding WD19X24394. Contact our support team with your model number if you need confirmation before ordering.
Compatibility
This drain pump kit is compatible with select dishwashers from the following GE product lines:
- GE dishwashers — GDF510, GDF520, GDF530, GDF535, GDF570, GDF620, GDF630, GDF640, GDF645, GDF650 series
- GE dishwashers — GDT530, GDT535, GDT545, GDT580, GDT605, GDT625, GDT630, GDT635, GDT645, GDT655, GDT695 series
- GE dishwashers — GDP615, GDP645, GDP665 series
- GE dishwashers — DDT575, DDT595 series
- GE Profile dishwashers — PDT715, PDT720, PDT760, PDT775, PDT785, PDT820, PDT825 series
- GE Café dishwashers — CDT836, CDT875 series
- GE Monogram dishwashers — ZDT925, ZDT985 series
- Hotpoint dishwashers — HDF310, HDF330 series
- Haier dishwashers (select GE-platform models)
- Kenmore / Sears dishwashers (select GE-built models)
Important: Replacing this drain pump requires pulling the dishwasher out from under the counter and tilting it on its side to access the pump from the underside. The pump is not accessible from inside the tub. Always verify your model number before ordering.
Key Features
- Genuine OEM part manufactured by GE to factory specifications — guaranteed fit and performance
- Removes wastewater from the tub during each drain phase so the dishwasher can advance through the wash cycle properly
- Engineered for quiet operation — minimizes noise during the drain cycle
- Current production part — directly supersedes WD19X24394
- Compatible with GE, GE Profile, GE Café, GE Monogram, Hotpoint, Haier, and Kenmore dishwashers
- Note: dishwasher must be pulled out and tilted for pump access — not accessible from inside the tub
- Installs in 30–45 minutes with basic hand tools
Product Specifications
| Part Number |
WD19X24829 |
| Supersedes |
WD19X24394 |
| Part Type |
Dishwasher Drain Pump Kit |
| Condition |
Genuine OEM |
| Access Method |
Dishwasher must be pulled out and tilted — pump on underside |
| Compatible Brands |
GE, GE Profile, GE Café, GE Monogram, Hotpoint, Haier, Kenmore |
Installation Notes
⚠️ Unplug Dishwasher and Shut Off Water Before Starting Disconnect power and shut off the water supply before beginning. This repair requires pulling the dishwasher out from under the counter. Disconnect the water supply line, drain hose, and electrical connection before pulling the unit out. Place a blanket or cardboard on the floor and carefully lay the dishwasher on its side to access the drain pump on the underside. Loosen the hose clamps at both ends of the pump and disconnect the drain hoses. Disconnect the pump wiring connector. Rotate or unscrew the old pump assembly to release it from the pump housing. Install the new WD19X24829 pump in the same position, reconnect the hoses and wiring connector, and secure the clamps and mounting hardware. Return the dishwasher to upright, reconnect the supply line, drain hose, and electrical connection, and slide it back under the counter. Restore power and water and run a test cycle to confirm normal drainage and check for leaks. Tools needed: Phillips screwdriver, pliers, adjustable wrench, blanket or cardboard.
Frequently Asked Questions
What is the difference between WD19X24829 and WD19X24394?
These are the same dishwasher drain pump kit. WD19X24829 is the current production part number that GE issued to supersede the earlier WD19X24394. If your dishwasher's parts diagram shows WD19X24394, the WD19X24829 is the correct current replacement to order.
Why does this pump require pulling the dishwasher out?
Unlike some dishwasher drain pumps that are accessible from inside the tub through the filter and pump cover, the drain pump on compatible GE models is mounted to the exterior underside of the dishwasher tub. It cannot be reached from inside without removing the entire tub assembly — which is a much larger repair. Pulling the dishwasher out from the cabinet, disconnecting it, and tilting it onto its side is the standard and only practical method for replacing this pump on compatible models.
What is the difference between the drain pump (WD19X24829) and the circulation pump (WD26X23258)?
These are two completely different pumps that serve different functions. The drain pump (WD19X24829) removes wastewater from the tub at the end of each wash and rinse cycle — it is the pump responsible for draining. The circulation pump (WD26X23258) pressurizes clean water and sends it to the spray arms during the wash cycle — it is responsible for cleaning. When the drain pump fails, the dishwasher won't drain and leaves standing water. When the circulation pump fails, the dishwasher drains normally but dishes don't get clean because no water is being sprayed.
My dishwasher has standing water — is it always the drain pump?
Not always. Standing water in a dishwasher after a cycle can be caused by a failed drain pump, a clogged drain filter, a blocked or kinked drain hose, a clogged garbage disposal connection, or a failed drain solenoid. Before replacing the pump, check the dishwasher drain filter (accessible from inside the tub at the bottom), confirm the drain hose is not kinked, and check whether the garbage disposal knockout plug has been removed if the drain hose connects to a new disposal. If all of these are clear and the dishwasher still won't drain, the pump is the most likely cause.
Is this a Genuine OEM or aftermarket part?
This is a Genuine OEM part manufactured by GE to factory specifications. It is the exact same drain pump kit installed in compatible GE, GE Profile, GE Café, and Monogram dishwashers from the factory — guaranteed fit, materials, and performance.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
