WE03X37319 Dryer Drum Bearing Slide (2-Pack) — Genuine OEM
The WE03X37319 is a genuine OEM 2-pack of front drum bearing slides from GE. These white molded plastic slides are one of several position-specific slide profiles that GE uses in the front bearing assembly of its dryers. The front bearing ring has multiple slots, and each pair of slots is shaped to accept a slide with a particular profile. The WE03X37319 fits its designated pair of slots — it is not interchangeable with the other GE bearing slides such as the WE03X37317, WE03X37318, or WE03X37320, which are shaped for different positions on the same ring. This position-specific design ensures each section of the drum rim contacts the correct glide surface for even support and smooth rotation.
Each slide in this 2-pack has a snap-fit tab that locks it into the bearing ring. The white plastic provides a low-friction surface for the drum to ride on as it turns. Over thousands of drying cycles the drum wears through the slide material, eventually reaching the point where plastic-on-metal contact becomes metal-on-metal contact. That transition is what produces the squealing or scraping noise that signals replacement is needed. Because both slides in the same position pair wear at the same rate, GE sells them together so you replace both at once.
QUICK ANSWER
Will This Fix Your Dryer?
If your GE or Hotpoint dryer squeals, scrapes, or leaves dark marks on clothes, worn front bearing slides are the most likely cause. The WE03X37319 is a genuine OEM 2-pack of white bearing slides for a specific position on the front bearing assembly. Check your parts diagram to confirm this is the correct slide for the position that needs replacement. Easy to moderate install, approximately 30 minutes to 1 hour.
Common Symptoms
- Squealing or squeaking noise during the tumble cycle
- Scraping or grinding sound from the front of the dryer
- Dark marks or streaks appearing on clothes after drying
- Drum rotation feels rough or catches when spun by hand
- Visible wear-through or grooves on existing bearing slides
Cross Reference Information
The WE03X37319 is GE's current part number for this white dryer drum bearing slide 2-pack. It supersedes earlier numbers WE3M51 and WE1M404 and cross-references to the following distributor catalog numbers.
WE03X37319 replaces WE3M51, WE01M0404, WE1M404, AGE25719, AP7217725, EAP17137207, FIX17137207, OEM21653184, PD00088117, PS17137207
COMPATIBILITY
This genuine OEM bearing slide 2-pack fits select GE, Hotpoint, and Kenmore dryers and washer/dryer combos. These slides mount in a specific pair of slots on the front bearing assembly — confirm your model number and check the parts diagram to verify the WE03X37319 is the correct slide for the position that needs replacement.
Sample compatible models: GTD42EASJ2WW, GTD65EBSJ0WS, GTD75ECPL0DG, GFD45ESSM0WW, GTDP490ED5WS, GTX22EASK0WW, HTDX100ED3WW, HTX24EASK0WS, GUD27ESSJ1WW, PFDS450EL2WW
Key Features
- Genuine OEM GE dryer drum bearing slide — not an aftermarket equivalent
- Sold as a 2-pack — replace both slides in the same bearing position together
- White molded plastic with snap-fit tab for secure seating in the bearing ring
- Position-specific profile — shaped to fit its designated pair of slots on the front bearing
- Eliminates squealing and scraping caused by worn-through bearing pads
- Easy to moderate installation — approximately 30 minutes to 1 hour
Specifications
| Part Number |
WE03X37319 |
| OEM Part Number |
WE03X37319 |
| Condition |
New |
| Brand |
GE |
| Part Type |
Dryer Drum Bearing Slide |
| Appliance Type |
Dryer / Washer Dryer Combo |
| Color |
White |
| Quantity |
2-Pack |
| Compatible Brands |
GE, Hotpoint, Kenmore |
| Supersedes |
WE3M51, WE1M404 |
Safety Warning
Disconnect the dryer from its power source before opening the cabinet. For gas models, also shut off the gas supply valve behind the unit. The front panel must be removed to reach the bearing assembly, which requires disconnecting the door switch wiring harness — photograph the wire positions before disconnecting. When lifting or supporting the drum, handle it evenly to avoid bending the drum rim. Snap the new slides into the correct bearing slots and press firmly until the tab clicks into place. Do not force a slide into a slot shaped for a different profile — if the slide does not seat easily, verify you have the correct part number for that position.
Frequently Asked Questions
Why does GE use different slide part numbers for different bearing positions?
The front bearing ring is not symmetrical — the slots at different positions around the ring have slightly different shapes and angles to distribute the drum's weight evenly. Each slide profile is molded to match the geometry of its specific slot pair. This ensures the drum rim contacts a properly contoured glide surface at every point. The WE03X37319 (white) fits one pair of positions, while the WE03X37317, WE03X37318, and WE03X37320 fit the other positions. They are not interchangeable, so always check your parts diagram to match the slide to the correct slot.
How do I identify which bearing slide position needs replacement?
Remove the front panel and visually inspect each slide in the bearing ring. A worn slide will show shiny grooves, flattened areas, or sections where the plastic has worn through to the metal beneath. Compare what you see to the parts diagram for your model — the diagram labels each slide position with its own part number. Order only the slide that matches the worn position. If multiple positions are worn, order the correct part number for each one.
Can I use the WE03X37320 (green) in place of the WE03X37319 (white)?
No. The green and white slides have different profiles and snap-fit tab positions. Even if a green slide physically fits into a white slide's slot, it will not seat correctly and will not provide the right contact angle for the drum. Using the wrong slide can cause uneven drum support, accelerate wear on the new slide, and may create noise instead of eliminating it. Always use the part number specified for each position.
Should I replace all four slide types at once even if only one pair is worn?
Not necessarily. If only the WE03X37319 pair shows visible wear, you can replace just that pair and leave the others. However, if the dryer has high hours and the other slides are showing early signs of wear — surface glazing, light grooves, or discoloration — it makes sense to replace them all while you have the front panel off. Opening the dryer again later for a second set of slides costs more time than replacing them in one job.
Are WE3M51 and WE1M404 the same as WE03X37319?
Yes. WE3M51 and WE1M404 are earlier GE part numbers that have been superseded by the WE03X37319. The current slides may differ slightly in appearance from the originals because GE updates the mold and material over time, but they fit the same bearing slots and perform the same function. If your parts diagram or old slide shows either of those numbers, the WE03X37319 is the correct current replacement.
Genuine OEM Part
Fast Shipping
In Stock
30–60 Minute Install