WH16X27182 Washer Suspension Rod Assembly (24-Inch) — Genuine OEM
Product Description
The WH16X27182 is a genuine OEM suspension rod assembly for GE unitized laundry centers (stacked washer/dryer combinations). This 24-inch rod connects the washer tub to the outer cabinet frame and functions as a damper — it absorbs the kinetic energy generated when wet laundry shifts to one side of the tub during the wash and spin cycles. Each rod consists of a steel shaft with a spring mechanism and friction-fit ball joints at each end. The spring compresses and rebounds as the tub oscillates, and the ball joints pivot to follow the tub's movement in multiple directions. The combined effect is controlled deceleration: the rod converts the tub's lateral and vertical movement into spring compression and friction heat, which dissipates harmlessly into the cabinet rather than transferring to the floor as vibration, walking, or structural noise.
GE unitized laundry centers in the GUD24 platform use multiple suspension rods — typically four — to cradle the washer tub. Each rod is sold individually, and the rods come in two part numbers that correspond to different mounting positions on the cabinet frame. When one or more rods fail, the tub loses its damping at that attachment point and begins swinging wider on every cycle. The most common mode of failure is spring fatigue — after thousands of compression-rebound cycles over years of use, the spring loses its tension and can no longer absorb tub oscillation effectively. The ball joints at either end can also crack, corrode, or wear smooth from moisture exposure in the humid environment inside the cabinet, causing the rod to detach or rattle loosely in its socket. Because the rods work as a system, a single failed rod puts increased stress on the remaining rods and accelerates their wear.
Quick Answer
Is a Worn Suspension Rod Causing Your Laundry Center to Shake?
A GE unitized laundry center that vibrates excessively, shakes hard during the spin cycle, produces loud banging or knocking sounds, or walks across the floor may have one or more worn suspension rods. These rods dampen the natural movement of the washer tub — when their springs lose tension or their ball joints crack, the tub swings freely and hammers against the cabinet walls. Before replacing rods, confirm the laundry center is level, the load is not severely unbalanced, and the unit is on a solid floor surface. If the machine still shakes violently with a small balanced load, the suspension system is the likely cause. This rod is sold individually — most technicians recommend replacing all rods at the same time, since a new rod paired with worn rods creates uneven damping and can cause the tub to track off-center.
Common Symptoms
Excessive vibration and shaking during the wash or spin cycle
Loud banging, knocking, or thumping sounds from inside the cabinet
Laundry center walks or moves across the floor during operation
Washer tub visibly off-center or tilted when at rest
Increased noise with unbalanced loads that the machine previously handled
Replaces Part Numbers
The WH16X27182 is the current GE part number for the 24-inch washer suspension rod assembly used in select unitized laundry centers. It replaces the following part and catalog numbers.
WH16X27182 replaces 4588128, AGE26970, AP6328301, EAP12343389, PD00062746, PS12343389
Compatibility & Model Cross Reference
This genuine OEM suspension rod fits select GE-manufactured unitized laundry centers (stacked washer/dryer combos). Always confirm your specific model number against the manufacturer's parts diagram before ordering.
GE (General Electric): GUD24ESSM0WW, GUD24ESSM1WW, GUD24GSSM0WW, GUD24GSSM1WW
Hotpoint / RCA / Kenmore: Select unitized laundry center models using the same 24-inch rod platform
This is a partial list of verified sample models — not every model from these brands uses this rod. GE laundry centers use different rod lengths depending on the platform. Your model number is typically on a label inside the washer lid or on the rear cabinet panel. Not sure if this fits? Send us your model number and we'll confirm compatibility before you order.
Key Features
Genuine OEM GE suspension rod assembly — 24 inches long
Steel shaft with spring damper mechanism absorbs tub oscillation during wash and spin
Ball joints at each end allow multi-directional pivot as the tub moves
Designed for GE unitized laundry centers (stacked washer/dryer combos)
Sold individually — multiple rods per machine (check parts diagram for your model)
Replaces earlier rod revision WH16X27181
Product Specifications
Part Number
WH16X27182
Condition
New
Brand
GE (General Electric)
Part Type
Washer Suspension Rod Assembly
Appliance Type
Unitized Laundry Center (Stacked Washer/Dryer)
Rod Length
24 inches
Material
Steel shaft with spring and polymer ball joints
Quantity
1 (sold individually)
Supersedes
WH16X27181
Installation & Safety Notes
Safety Warning
Unplug the laundry center from the wall outlet before beginning any work. Because this is a stacked unit, ensure the machine is stable and will not tip during service — do not attempt to tilt or move the unit without a helper. Wear work gloves to protect your hands from sharp cabinet edges. When removing old rods, support the washer tub to prevent it from dropping onto internal components. After installing the new rod(s), confirm all mounting points are fully seated before restoring power.
Frequently Asked Questions
How do suspension rods work inside a GE laundry center?
The suspension rods connect the washer tub assembly to the outer cabinet frame. Each rod contains a spring mechanism that compresses when the tub moves toward the cabinet wall and rebounds when the tub moves away. Ball joints at each end allow the rod to pivot freely as the tub oscillates in multiple directions during agitation and spin. Together, the rods form a damping system that converts the tub's kinetic energy into spring compression and friction heat, preventing the tub from slamming into the cabinet walls and transferring vibration to the floor. The system is designed to handle normal load imbalances — a few heavier items on one side of the tub — without excessive shaking or noise.
What causes suspension rods to fail?
The most common cause is spring fatigue. Each rod's spring compresses and rebounds thousands of times during every wash cycle, and over years of use the metal gradually loses its elasticity. A fatigued spring cannot absorb tub oscillation as effectively, so the tub swings wider and hits harder. The ball joints at each end also degrade — the humid environment inside a laundry center promotes corrosion on metal surfaces and drying/cracking on polymer components. Repeatedly overloading the washer or running frequent unbalanced loads accelerates wear on both the springs and joints because the rods absorb more force per cycle than they were designed for.
Why does GE use two different rod part numbers on the same laundry center?
GE unitized laundry centers in the GUD24 platform use rods in different mounting positions on the cabinet frame. The two part numbers correspond to rods designed for specific positions — typically front and rear, or left and right — which may differ in spring tension, angle, or ball joint configuration to match the geometry of that mounting point. When ordering, check your model's parts diagram to confirm which part number goes in which position and how many of each you need.
Should I replace all suspension rods at once or just the failed one?
Most technicians recommend replacing all rods at the same time. The rods work as a balanced system — each one shares the load of dampening tub movement. If you install one new rod with full spring tension alongside worn rods with reduced tension, the tub's damping becomes uneven. The new rod will absorb more force on its side while the worn rods allow more movement on theirs, which can cause the tub to track off-center and produce a wobble that was not present before. Replacing all rods at once ensures even damping across the entire tub.
How can I tell if the suspension rods are worn without disassembling the machine?
Open the washer lid and firmly press down on the washer tub with both hands, then release. A healthy suspension system will let the tub drop and return to center with one or two controlled bounces. If the tub bounces repeatedly, swings side to side before settling, or drops and stays low without rebounding, one or more rods have lost their damping ability. You can also run a small balanced load on the spin cycle — if the entire unit shakes, vibrates, or walks across the floor with a load it previously handled, the rods are the likely cause after confirming the machine is level.
Is the 24-inch rod length specific to my model?
Yes. GE manufactures suspension rods in different lengths for different laundry center platforms. The WH16X27182 is a 24-inch rod designed specifically for the GUD24 series of unitized laundry centers. Other GE platforms use 27-inch or other-length rods that are physically incompatible with the GUD24 mounting points. Always confirm the correct rod length by checking the parts diagram for your specific model number — installing a rod of the wrong length will not seat properly and can damage the tub or cabinet.
Genuine OEM Part
Fast Shipping
Easy Installation
Please verify your appliance model number before ordering.