Genuine OEM WH23X10043 Washer Drain Pump
The WH23X10043 is a genuine OEM drain pump from GE for GE and Hotpoint washers. The drain pump pushes wash water out of the tub and through the drain hose during the drain portion of the cycle. When it clogs, wears out, or leaks, the washer may leave water in the drum, stop before the spin, throw drain-related problems, leak from the pump, or make unusual noise while draining.
This is a genuine OEM part, not an aftermarket equivalent, so the fit and operation match the original pump. It is a straightforward repair for most owners, usually under an hour, with a nutdriver, pliers and screwdrivers.
Quick Answer
The Genuine OEM WH23X10043 Drain Pump fixes a GE or Hotpoint washer that won't drain, leaves water in the drum, drains slowly, leaks from the pump, or makes noise while draining because the pump has failed. Genuine OEM from GE Appliances. Classic symptom: the cycle stalls with water still in the tub, or you hear the pump hum or grind but the water doesn't leave.
Common Problems This Part Fixes
- Washer won't drain, or water is left in the drum after the cycle
- Slow or incomplete draining
- Water leaking from the pump
- Unusual noise while the washer drains
- Cycle stopping before the spin because the water hasn't drained
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This drain pump is listed under the following part number:
WH23X10043, 2754597, DP035-043, AGE26084, AP5632594, EAP3654194, PD00023322, PS3654194
We have not found any superseded or alternate manufacturer numbers for this pump. If your old pump or parts diagram shows a different number, contact our support team and we'll check whether it matches.
Compatibility
This drain pump is listed for washers from:
- GE, including GBAN2800F0WW, GCWN4950D0WS, GHWN4250D0WW, GLWN5550D0WW, GMAN4250F0WS, and GTWN5650F2WS
- Hotpoint, including HTAP1200D1WW and MTAP1200D0WW
Note: The model list above is only a sample, since retailers list 100 or more compatible models. Confirm fit by matching the number on your old pump or your parts diagram, or contact our support team with your model number and we'll verify before you order.
Key Features
- Genuine OEM GE washer drain pump, not an aftermarket equivalent
- Restores full draining so cycles finish and the washer can spin
- Fits a wide range of GE and Hotpoint washers
- Simple replacement, typically under an hour with basic hand tools
Product Specifications
| Part Number |
WH23X10043 |
| OEM Part Number |
WH23X10043 |
| Part Type |
Washer Drain Pump |
| Condition |
Genuine OEM |
| Manufacturer |
GE Appliances |
| Approx. Size |
About 9 in H x 6 in L x 4 in Thick |
| Application |
Select GE & Hotpoint Washers |
Installation Notes
⚠️ Unplug Power and Expect Water Unplug the washer and turn off the water supply before starting. Work gloves are recommended. Put towels and a shallow pan under the work area, since some water will remain in the pump and hoses. Following your model's service guide, remove the panel needed to reach the pump, disconnect its wiring connector, and loosen the clamps holding the hoses. Pull the hoses off, remove the pump's mounting fasteners, and take out the old pump. Install the new pump in the same position, reattach the hoses with their clamps (replace worn clamps if needed), and reconnect the wiring. Replace the panel, restore power and water, and run a drain cycle while checking for leaks. Reviewers note the hose clamps can be difficult, so have pliers ready.
Frequently Asked Questions
My washer won't drain. Is this the part I need?
A failed or clogged drain pump is a common cause. Before replacing it, check the drain hose and the pump for a clog from a sock, coin, or lint. If the path is clear but the pump hums, grinds, leaks, or doesn't run, replacing it should fix the problem.
Will this fit my GE or Hotpoint washer?
It is listed for a wide range of GE and Hotpoint washers. Match the number on your old pump or parts diagram, or contact our support team with your model number and we'll confirm fit before you order.
Do I need special tools?
No. A nutdriver, pliers, and screwdrivers are typically all you need. Pliers help with the hose clamps.
Is this a genuine GE part?
Yes. This is a genuine OEM part from GE Appliances, not an aftermarket equivalent.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping ✓ Genuine OEM Parts ✓ Compatibility Support ✓ Secure Checkout
