WR30X30972 Refrigerator Ice Maker Assembly — Genuine OEM GE
Product Description
The WR30X30972 is a genuine OEM 7-cube ice maker assembly for select GE-manufactured refrigerators. It is a complete self-contained unit — the ice mold, control module, motor, ejector mechanism, and wiring harness are all built into a single assembly that mounts inside the freezer compartment. The ice maker operates on an automatic repeating cycle: the water inlet valve opens to fill the mold with a measured dose of water, the freezer's ambient temperature freezes the water into cubes, a thermostat inside the ice maker senses when the mold has reached the target temperature, and the control module then activates the motor to rotate the ejector arms and push the finished cubes out of the mold and into the ice bin below.
Once the ejector cycle completes, the control module signals the water inlet valve to refill the mold and the cycle begins again. This continues automatically until the bail arm (a wire lever on the side of the ice maker) is pushed up by a full ice bin — that mechanically trips a shutoff switch inside the module that pauses the cycle. When ice is removed from the bin and the bail arm drops back down, the cycle resumes. The entire process depends on three things working together: a functioning water supply to the inlet valve, a freezer temperature cold enough to freeze the mold (0–5°F is the target range), and an ice maker assembly whose internal motor, thermostat, and control module are all operating correctly. A failure in any one of those stops ice production.
Quick Answer
Why Did the Refrigerator Stop Making Ice?
An ice maker that suddenly stops producing cubes — or produces only a few small, misshapen cubes — usually points to either a failed ice maker assembly or a problem with the water or temperature conditions it depends on. Before replacing the ice maker, check the basics: verify the freezer is at 0–5°F (above 10°F and the ice maker cannot function), confirm the water supply valve behind the refrigerator is fully open, and check that the water filter is not overdue for replacement. If water is reaching the mold and the freezer is cold enough but the ice maker still does not cycle, the internal motor, thermostat, or control module has likely failed. Because individual components inside the ice maker are not sold separately, the entire assembly must be replaced. The WR30X30972 is the genuine OEM replacement for select GE, Hotpoint, Café, Haier, and RCA refrigerators.
Common Symptoms
- Ice maker not producing any ice
- Ice maker produces only a few small or misshapen cubes per cycle
- Ice maker does not cycle — mold fills with water but cubes are never ejected
- Ejector arms do not rotate to push cubes into the bin
- Ice maker runs continuously and overfills the bin (bail arm shutoff not engaging)
- Water leaks from the ice maker area inside the freezer
Replaces Part Numbers
The WR30X30972 is the current GE part number for this ice maker assembly. It replaces the following part and cross-reference numbers.
WR30X30972 replaces WR30X28702, 4930938, SWR29X5128, WR29X5128, WR29X5178, WR30X10014, WR30X30719, 162D3868G010, 245D2613P002, AGE28619, AP6891612, EAP12727331, OEM20674845, PD00051943, PS12727331
Compatibility & Model Cross Reference
This genuine OEM ice maker assembly fits select GE-manufactured refrigerators across multiple platforms — including top-freezer, bottom-freezer, side-by-side, and built-in configurations. It also fits select Hotpoint, Café, Haier, and RCA models, as well as select Kenmore refrigerators manufactured by GE. Always confirm your model number against the manufacturer's parts diagram before ordering.
GE Top-Freezer: GTS18HCMERCC, GTS18HCMFRWW, GTS22KSNCRSS, and other select GTS models
GE Bottom-Freezer: GBE21DGKTRBB, GBE21DGKTRWW, and other select GBE models
GE Side-by-Side: GSS22JETNWW, GSS25LSTCSS, GSH22JSXPSS, GSH22JSZBSS, DSS25KSTESS, DSF25KGTEBG, and other select GSS/GSH/DSS/DSF models
GE Profile / Café / Monogram: PSE26KGEBEBB, ZISW480DXB, ZISP480DTBSS, ZISS480NXBSS, and other select models
Hotpoint: HSS22GFTNWW and other select HSS models
This is a small sample — the WR30X30972 fits over 1,100 models. Not every GE-branded refrigerator uses this ice maker assembly. Your model number is on a label inside the refrigerator compartment (usually on the side wall or ceiling). Not sure if this is the right ice maker for your model? Send us your model number and we'll confirm.
Key Features
- Genuine OEM GE ice maker assembly — complete 7-cube unit
- Includes ice mold, control module, motor, ejector mechanism, and wiring harness
- Automatic fill-freeze-harvest-eject cycle
- Bail arm mechanical shutoff stops production when bin is full
- Fits select GE, Hotpoint, Café, Haier, RCA, and Kenmore refrigerators
- Direct replacement — same mounting holes and harness connector as the original
Product Specifications
| Part Number |
WR30X30972 |
| Condition |
New |
| Brand |
GE |
| Part Type |
Ice Maker Assembly (7-Cube) |
| Appliance Type |
Refrigerator |
| Material |
Molded Plastic Housing with Internal Motor and Ejector |
| Weight |
Approx. 1.0–1.5 lbs |
Installation & Safety Notes
Safety Warning
Disconnect the refrigerator from the electrical outlet and shut off the water supply valve before beginning work. Remove the ice bin to access the ice maker mounting area. Disconnect the wire harness from the old ice maker, remove the mounting screws, and lift the assembly out. Install the new WR30X30972 in reverse order — secure with mounting screws and reconnect the wire harness. After installation, restore power and water supply, then allow 24 hours for the ice maker to begin producing ice. The first batch or two may be undersized or off-tasting — discard them. Verify that the freezer temperature is set between 0°F and 5°F for proper ice production.
Frequently Asked Questions
- How does the automatic ice maker cycle work?
- The cycle has four stages that repeat automatically. First, the control module signals the water inlet valve to open for a few seconds, delivering a measured amount of water into the ice mold. Second, the water sits in the mold while the freezer's ambient air freezes it into cubes — this is the longest stage and depends entirely on the freezer temperature. Third, a thermostat embedded in the ice maker senses when the mold reaches the target temperature (indicating the water is fully frozen) and signals the control module to begin the harvest. Fourth, the motor rotates the ejector arms, which push the cubes up and out of the mold into the ice bin, then return to the starting position. At the end of the ejector rotation, the control module triggers another fill and the cycle starts over.
- What causes the ice maker to stop producing ice?
- Ice production depends on three systems working together — the water supply, the freezer temperature, and the ice maker assembly itself. The most common causes of failure are: a clogged or overdue water filter that reduces water flow to the inlet valve, a freezer temperature that is too warm (above 10°F and the ice maker cannot complete its cycle), a frozen fill tube that blocks water from reaching the mold, a failed water inlet valve that does not open when signaled, or a failed ice maker assembly whose internal thermostat, motor, or control module has stopped working. Always check the simpler causes — water supply, filter, and freezer temperature — before replacing the ice maker.
- Why does freezer temperature matter so much?
- The ice maker's internal thermostat controls the entire cycle. It waits until the mold drops to a specific temperature before initiating the harvest — if the freezer is too warm, the thermostat never reaches that threshold and the cycle stalls. The recommended range is 0°F to 5°F (–18°C to –15°C). Above 10°F, the ice maker generally cannot produce ice at all. Conversely, a freezer set far below 0°F can freeze the water fill tube solid, which prevents water from reaching the mold — so the ice maker cycles but produces no cubes because the mold is empty.
- What is the bail arm and how does it control ice production?
- The bail arm is a metal wire lever on the side of the ice maker. It acts as a mechanical on/off switch. When the ice bin fills up, the pile of cubes physically pushes the bail arm upward, which trips a shutoff switch inside the control module and stops the cycle. When you remove ice from the bin, the bail arm drops back down under its own weight, the switch resets, and the cycle resumes. If you need to manually stop ice production — for example, when going on vacation — you can lift the bail arm into the up position by hand. If the bail arm is stuck in the up position or jammed by ice buildup around it, the ice maker will not cycle even though nothing is mechanically wrong with it.
- Can individual components inside the ice maker be replaced separately?
- No. The motor, thermostat, control module, ejector mechanism, and mold are all integrated into a single sealed assembly. If any one internal component fails — a motor that does not turn, a thermostat that does not sense correctly, a control module that does not signal — the entire ice maker assembly must be replaced. This is a GE design decision. The WR30X30972 is the complete replacement unit.
- How long does it take for the new ice maker to start producing ice after installation?
- Allow up to 24 hours after restoring power and water supply. The ice maker needs to acclimate to the freezer temperature before its thermostat begins cycling normally. The first one or two batches of cubes may be smaller than normal or have an off taste from manufacturing residues — discard those initial batches. Full production depends on the freezer holding the proper temperature range (0°F to 5°F) and adequate water pressure reaching the inlet valve.
Genuine OEM Part
Fast Shipping
Easy Installation
Please verify your appliance model number before ordering.