XPARTCO DC97-16350ST Washer Suspension Rod Kit (Set of 4)
Inside every Samsung top-load washer, four suspension rods connect the outer tub to the base frame. Each rod is a spring-loaded damper — a steel rod inside a coil spring with a rubber bushing at each end — that absorbs the violent tub movement generated during high-speed spin cycles. When a rod's spring weakens or its rubber bushing cracks, the tub swings too far in that direction, causing the entire washer to vibrate, walk across the floor, or trigger a UE (unbalanced) error code and shut down mid-cycle.
The XPARTCO DC97-16350ST is a complete matched set of all four rods — two DC97-16350S rods (rear position, white spring) and two DC97-16350T rods (front position, pink spring). Samsung uses two different rod types because the front and rear mounting positions handle different directional loads during spin. This kit provides all four in one package so every rod has identical new spring tension, eliminating the uneven damping that causes tub imbalance when only one or two rods are replaced.
Quick Answer
Will This Fix My Washer? Yes — if your Samsung top-load washer vibrates excessively, walks during spin, makes loud banging noises, or throws a UE/UB error code, worn suspension rods are the most common cause. This XPARTCO DC97-16350ST kit replaces all four rods at once with a matched set of 2 rear (S-type, white) and 2 front (T-type, pink). Key diagnostic: push the tub firmly from side to side — if it rocks more than about an inch in any direction, the rods are worn.
Common Symptoms of Worn Suspension Rods
- Washer vibrates heavily or shakes during spin cycle
- Washer walks or moves across the floor during use
- Loud banging or thumping noise during spin
- Samsung displays UE, UB, or dC error code mid-cycle
- Tub rocks excessively when pushed by hand
- Visible spring damage, rust, or cracked rubber bushings on existing rods
Cross Reference Information
Part numbers can change over a product's lifecycle. Below are the known cross-reference numbers this kit replaces. The S-type rods serve the rear positions and the T-type rods serve the front positions.
XPDC97-16350ST, DC97-16350S, DC97-16350T, AP6806420, AP6806421, ASM105145, ASM143652, EAP12708544, EAP12592527, PD00070381, PD00069414, PS12708544, PS12592527
Compatibility
This suspension rod kit fits select Samsung top-load washers, including:
- WA50R5200AW, WA50R5200AV, WA50R5400AV, WA50R5400AW
- WA45T3200AW, WA45T3400AV, WA45T3400AW
- WA45N3050AW, WA45H7000AW, WA45M7050AW
- WA44A3205AW, WA44A3405AP, WA44A3405AV, WA44A3405AW
- WA41A3000AW, WA40A3005AW, WA50T5300AC
Note: This is a partial list. Samsung uses the DC97-16350S and DC97-16350T rods across many WA-series top-load models. Confirm your model number uses these two rod part numbers in your parts diagram before ordering, or contact us and we'll verify compatibility.
Key Features
- Complete matched set of 4 suspension rods — 2x DC97-16350S (rear, white) and 2x DC97-16350T (front, pink)
- XPARTCO aftermarket replacement — engineered for OEM-equivalent fit and performance
- High-grade stainless steel rods with rubber dampers and plastic end caps
- 26.4" overall length per rod, 1-3/8" diameter — matches Samsung factory dimensions
- Reduces excessive vibration, tub movement, and noise during spin cycles
- Cost-effective alternative to replacing rods individually at OEM prices
Product Specifications
| Part Number |
XPDC97-16350ST |
| OEM Part Number |
DC97-16350S / DC97-16350T |
| Part Type |
Washer Suspension Rod Kit |
| Kit Contents |
Set of 4 (2x S-type rear + 2x T-type front) |
| Condition |
Aftermarket |
| Brand |
XPARTCO |
| Material |
High-grade stainless steel with rubber dampers |
| Overall Length |
26.4" per rod |
| Rod Diameter |
1-3/8" |
| Compatible Brand |
Samsung |
Safety & Installation
Unplug the washer before starting. Tilt the washer back against a wall or have a helper hold it steady. Remove the top panel (usually two screws at the rear) and locate the four suspension rods connecting the tub to the base frame — two at the rear (white springs) and two at the front (pink springs). Unhook each rod from the tub bracket at the top, then release it from the base frame at the bottom. If wiring or hoses are clipped to a rod, unclip them first and reattach to the new rod. Install the new S-type rods (white) at the rear positions and the T-type rods (pink) at the front positions. Do not swap front and rear — the rod types are position-specific. Reassemble the top panel, plug in the washer, and run an empty spin cycle to confirm smooth operation. Typical install time: 30–45 minutes.
Frequently Asked Questions
Why does Samsung use two different rod types (S and T) in one washer?
The front and rear mounting positions experience different directional loads during spin. The S-type rods (white spring, rear position) and T-type rods (pink spring, front position) have slightly different spring rates tuned to their respective positions. This is why Samsung specifies 2 of each rather than 4 identical rods.
Can I replace just one or two rods instead of all four?
Technically yes, but it is strongly recommended to replace all four at the same time. Suspension rods wear at roughly the same rate, and mixing a new rod with worn rods creates uneven spring tension that can actually make vibration worse. The cost of one OEM rod is often close to this complete aftermarket kit of four.
How do I tell if my suspension rods are worn?
Open the top panel and push the tub firmly from side to side. A healthy tub on good rods moves slightly and returns to center. If the tub swings more than about an inch, rocks loosely, or does not spring back, the rods are worn. Also check each rod visually — look for stretched or broken springs, rust, cracked rubber bushings, or rods that are bent.
What happens if I put the S and T rods in the wrong positions?
The rods are color-coded for a reason — white springs go to the rear (S-type) and pink springs go to the front (T-type). Installing them in the wrong positions may result in continued vibration because the spring rates will not match the load profile at that position. Always match the rod color to the position of the rod you are removing.
My washer still vibrates after replacing the rods. What else should I check?
First confirm the rods are in the correct positions (white rear, pink front) and fully seated at both ends. Then check that the washer is level — all four leveling feet should contact the floor firmly. Also inspect the damper pads on the base frame, the spider arm assembly under the wash plate, and whether the load was distributed evenly in the tub. Persistent vibration with new rods and a level washer often points to a cracked spider arm.
XPARTCO Aftermarket Part
Fast Shipping
In Stock
30–45 Min Install
