XPARTCO DC97-16350V Washer Suspension Rod Kit (Set of 4)
The XPARTCO DC97-16350V is an aftermarket replacement washer suspension rod kit (set of 4) compatible with select Samsung top-load washers in the WA48, WA50, WA52, and WA54 series. The suspension rods are spring-loaded shock-absorbing rods that connect the outer tub to the top of the washer cabinet, suspending the tub and dampening the vibrations generated during agitation and high-speed spin cycles. All four rods work together to keep the tub centered and stable — when one or more rods weaken, break, or lose their spring tension, the tub swings off-center and strikes the cabinet walls, causing violent shaking, banging, error code dc (out of balance), UE imbalance errors, and progressive damage to the washer cabinet and internal components.
Each rod is 27.5 inches in overall length and is constructed from spring steel with a plastic top cap and bottom cup that clip into the tub and cabinet mounting points. The kit includes all 4 suspension rods — always replace all four at the same time since the rods wear at the same rate. It directly replaces DC97-16350T, DC97-16350U, DC97-16350S, DC97-16350E, DC97-16350D, DC97-16350K, DC97-18610C, AP6975426, and PS12740434. Installs in 20–30 minutes — no special tools required. Note: rods are coated with grease — wear gloves during installation.
Quick Answer
The XPARTCO DC97-16350V Washer Suspension Rod Kit fixes Samsung top-load washers that vibrate violently, bang loudly, walk across the floor, display dc or UE imbalance error codes, or stop mid-cycle during spin. Set of 4 rods, 27.5" overall length, spring steel. Replace all 4 at the same time. Wear gloves — rods are greased. Compatible with Samsung WA48, WA50, WA52, and WA54 series. Replaces DC97-16350T, DC97-16350U, DC97-16350S, DC97-16350E, DC97-18610C, AP6975426, PS12740434.
Common Problems This Kit Fixes
- Washer vibrating violently or shaking excessively during the spin cycle
- Loud banging or thumping — tub striking the cabinet walls during spin
- Washer "walking" or moving across the floor during high-speed spin
- Error code dc displayed — Samsung out-of-balance error during spin
- Error code UE displayed — unbalanced load error the washer cannot correct
- Washer repeatedly stopping and rebalancing the load without completing the spin cycle
- Visible broken, detached, or sagging suspension rod visible inside the cabinet
- Rattling or clunking noise during agitation — tub no longer centered
Replaces Part Numbers
This suspension rod kit directly replaces the following OEM and cross-reference part numbers:
DC97-16350V, AP6975426, EAP12740434, PS12740434, ASM34760, PD00071611.
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This suspension rod kit is compatible with select top-load washers from the following Samsung series:
- Samsung WA48 series — WA48H7400AW, WA48H7400AP, WA48J7700AW, WA48J7770AP and related models
- Samsung WA50 series — WA50F9A6DSW, WA50F9A7DSP, WA50F9A7DSW, WA50F9A8DSP, WA50R5200AW, WA50R5400AV, WA50T5300AC and related models
- Samsung WA52 series — WA52A5500AV, WA52A5500AW, WA52A5500AC and related models
- Samsung WA54 series — WA54R7200AV, WA54R7200AW, WA54R7600AC, WA54R7600AV, WA54R7600AW, WA5AR7200AV and related models
- Samsung WA45 series — WA45H7000AW, WA45K7600AW, WA45M7050AW (select models)
- Kenmore / Sears top-load washers (select Samsung-built models)
Important: Samsung uses several different suspension rod lengths across its top-load washer lineup. The DC97-16350V is 27.5 inches long and is for larger-capacity WA48–WA54 series models. Shorter-capacity models (WA40–WA45) typically use DC97-16350C or DC97-16350U rods. Always verify your model number before ordering to confirm you need the 27.5-inch version.
Key Features
- Set of 4 suspension rods — complete replacement kit covering all four tub mounting points
- Suspends and centers the outer tub within the cabinet — dampens agitation and spin vibration to prevent tub-to-cabinet contact
- Resolves Samsung error codes dc (out of balance) and UE (unbalanced load)
- 27.5 inches overall length — correct size for WA48, WA50, WA52, and WA54 series Samsung top-load washers
- Spring steel construction with plastic top cap and bottom cup — durable and corrosion resistant
- Rods are pre-coated with grease — wear work gloves during installation
- Replace all 4 rods at the same time — rods wear together and partial replacement leads to uneven tub support
- No special tools required — installs in 20–30 minutes
- Replaces DC97-16350T, DC97-16350U, DC97-16350S, DC97-16350E, DC97-18610C, and more
- Aftermarket replacement built to OEM-equivalent quality standards
Product Specifications
| Part Number |
DC97-16350V |
| Part Type |
Washer Suspension Rod and Spring Assembly |
| Condition |
Aftermarket Replacement |
| Application |
Samsung Top-Load Washers — WA48, WA50, WA52, WA54 series |
| Quantity |
Set of 4 (replace all four rods at the same time) |
| Rod Length |
27.5 inches overall |
| Material |
Spring steel / Plastic / Metal |
| Color |
Black / Silver / Gray |
| Lubrication |
Pre-coated with grease — wear gloves during installation |
| Error Codes Resolved |
dc (out of balance), UE (unbalanced load) |
| Compatible Brands |
Samsung, Kenmore (Samsung-built) |
Installation Notes
⚠️ Unplug Washer and Shut Off Water Before Starting — Wear Gloves Disconnect power and turn off the water supply before beginning. Wear work gloves throughout — the suspension rods are coated with grease. Remove the lid of the washer and the top panel (typically secured by screws under the lid hinge covers and at the rear corners). With the top panel removed, the four suspension rods are visible, each running from a mounting point on the tub rim up to a hook or bracket at the top corners of the cabinet frame. Note the orientation and attachment method of each rod before removing. Unhook the top of the old rod from the cabinet bracket and lift the bottom cup off the tub mounting pin. Install each new DC97-16350V rod by seating the bottom cup onto the tub mounting pin and hooking the top over the cabinet bracket. Replace all four rods before reassembling. Reinstall the top panel and lid, restore power and water, then run a spin cycle to verify smooth, stable operation. Tools needed: Phillips screwdriver; no special tools required for the rods themselves.
Frequently Asked Questions
What do the suspension rods do?
The suspension rods are spring-loaded shock absorbers that hang the outer washer tub from the top corners of the cabinet frame. They suspend the tub in the center of the cabinet and absorb the vibrations and movement generated during agitation and high-speed spin cycles. As long as all four rods have equal spring tension, the tub stays centered and stable. When one or more rods lose tension, stretch, or break, the tub is no longer held evenly and begins to swing off-center during spin — striking the cabinet walls, causing the loud banging, vibration, and imbalance error codes that indicate the rods need replacement.
Why must I replace all 4 rods instead of just the broken one?
All four suspension rods experience the same amount of wear over the same number of wash cycles. When one rod fails, the remaining three have experienced the same stress and fatigue and are likely to fail soon after. Replacing only the broken rod leaves three worn rods supporting the tub unevenly, which can cause the new rod to wear faster and may not fully resolve the vibration problem. Replacing all four at the same time ensures even tub support, fully resolves the imbalance, and prevents a repeat repair in the near future.
What do error codes dc and UE mean on Samsung washers?
On Samsung top-load washers, error code dc (or sometimes dC) means the washer has detected an out-of-balance condition during the spin cycle and has stopped to prevent damage. Error code UE means an unbalanced load that the machine cannot automatically correct by redistributing. Both codes can be caused by an actual overloaded or unevenly distributed laundry load — but if the errors occur frequently even with normal loads and proper load distribution, worn or broken suspension rods are the most common mechanical cause. Replacing the rod kit resolves these errors in most cases.
How is the DC97-16350V different from DC97-16350U or DC97-16350S?
The DC97-16350V, DC97-16350U, and DC97-16350S are all Samsung suspension rods, but they have different lengths for different washer model generations and capacities. The DC97-16350V is 27.5 inches long and is used on larger-capacity WA48–WA54 series Samsung washers. The DC97-16350U is approximately 26.4 inches and is used on mid-capacity WA45–WA50 series models. The DC97-16350S and DC97-16350C are shorter versions for earlier or smaller-capacity models. Using the wrong length rod can cause the tub to sit at the incorrect height inside the cabinet. Always verify your model number before ordering to confirm the correct rod length.
Is this an OEM or aftermarket part?
This is an aftermarket replacement kit built to OEM-equivalent quality standards. It is not a genuine Samsung OEM part, but is manufactured from spring steel with plastic end caps to match the length and spring tension of the original DC97-16350V suspension rods.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout
