XPARTCO W10849499 Dryer Drum Belt
The XPARTCO W10849499 is an aftermarket replacement drum belt for Whirlpool's large-capacity dryer platform. The belt wraps all the way around the outside of the drum, passes around the idler tension pulley, and loops around the drive motor pulley — that belt is the only mechanical connection between the motor and the drum, so when it breaks, the console still lights up, the motor still hums, and the blower still moves air, but the drum sits completely still. Open the door and spin the drum by hand and it will turn freely with no resistance.
This belt measures approximately 97.75 inches long. Belts fail from age and heat: the rubber hardens over years of thermal cycling, the ribs glaze over and begin slipping under a heavy wet load, and eventually the belt cracks through or snaps outright. A worn or seized idler pulley is also a common root cause of premature belt failure, since a pulley that won't turn freely forces the belt to drag continuously against a stationary surface until it shreds. Squealing or chirping at startup, a rhythmic thump timed to drum rotation, fraying at the edges, or black rubber dust in the cabinet are all signs a belt is near the end of its life. As an aftermarket replacement, the W10849499 is built to OEM-equivalent quality standards. It directly replaces AP5989682, 4383705, PS11731121, and W10610882.
Quick Answer
The XPARTCO W10849499 Dryer Drum Belt fixes Whirlpool large-capacity dryers where the motor runs but the drum won't turn, the drum spins freely by hand, or the dryer squeals, chirps, or thumps during operation. Approximately 97.75" long. Replaces AP5989682, 4383705, PS11731121, W10610882. If your belt broke due to a worn idler pulley rather than simple age, replace the pulley (PS334244) at the same time or the new belt will wear out quickly too.
Common Problems This Part Fixes
- Dryer runs and hums but the drum does not turn — the classic broken belt symptom
- Drum spins freely by hand with no resistance when the door is open
- Loud squealing, chirping, or scraping noise from inside the dryer
- Rhythmic thumping or slapping noise timed to drum rotation — cracked or split belt
- Drum turns slowly, intermittently, or stalls under a heavy wet load — glazed belt slipping
- Clothes not drying completely, or drying taking longer than it used to
- Broken belt pieces or fragments found inside the drum
- Visible cracking, fraying, glazing, or stretching on the old belt
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This dryer drum belt directly replaces the following OEM and cross-reference part numbers:
W10849499, W10610882, AP5989682, 4383705, AWP42591, EAP11731121, OEM17969055, PD00046442, PS11731121
W10610882 was the immediately preceding number for this same belt. If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This drum belt is compatible with select large-capacity Whirlpool-built dryers across the Whirlpool family of brands, including:
- Whirlpool large-capacity electric and gas dryers
- Maytag dryers (select Whirlpool-built models)
- KitchenAid, Jenn-Air, and Amana dryers (select models)
- Magic Chef, Admiral, Norge, Roper, and Inglis dryers (select models)
- Select Kenmore and Ikea dryers built on the Whirlpool platform
Verified model numbers include: YWED8500DC, YWED8000DW, YWED8500DW, 7MWGD8000E, and 7MWGD8500E.
Note: Whirlpool uses several different drum belt lengths across its dryer lineup, and this one is approximately 97.75" long — different from the shorter belts used on other Whirlpool-built platforms. Belts of a similar rib profile but a different length are not interchangeable; a belt that's too long or short for your drum will slip, walk off the pulley, or fail to seat properly. Verify your model number, or measure your old belt end to end, before ordering. Contact our support team with your model number if you're unsure.
Key Features
- Aftermarket replacement drum belt for Whirlpool's large-capacity dryer platform
- Approximately 97.75" in length
- Wraps around the drum, idler tension pulley, and drive motor pulley to transfer motor rotation to the drum
- Resolves "motor runs but drum won't turn," "squealing or chirping," and "drum spins freely by hand" symptoms
- Direct drop-in replacement — no cutting, splicing, or modification required
- Replaces W10610882, AP5989682, 4383705, and PS11731121
- Compatible with Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, Inglis, and Kenmore large-capacity dryers
- Aftermarket replacement built to OEM-equivalent quality standards
Product Specifications
| Part Number |
W10849499 |
| OEM Part Number |
W10849499 (formerly W10610882) |
| Part Type |
Dryer Drum Drive Belt |
| Condition |
Aftermarket Replacement |
| Application |
Whirlpool Large-Capacity Dryers |
| Length |
Approx. 97.75 in. |
| Routing |
Around drum → idler tension pulley → drive motor pulley |
| Fuel Type |
Electric and gas dryers |
| Companion Part |
Idler pulley PS334244 (check/replace if belt failed prematurely) |
| Quantity |
1 belt |
| Compatible Brands |
Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, Inglis, Kenmore |
Installation Notes
⚠️ Unplug Dryer Before Starting — A Second Person Helps Support The Drum Disconnect power at the outlet or shut off the circuit breaker before beginning. On a gas model, also close the gas shutoff valve before moving the cabinet. Wear work gloves — sheet metal edges inside the cabinet are sharp. On many large-capacity models, both the front and rear panels need to come off to fully access the belt and drum, so budget extra time compared to a simpler platform. Photograph how the old belt routes around the drum, the idler pulley, and the motor pulley before removing anything. Loosen and remove the motor mount or bracket as needed to slip the old belt free, and check the idler pulley by spinning it with your fingers — if it's stiff, gritty, or doesn't spin freely, replace it at the same time, since a worn pulley is a common cause of premature belt failure and will shorten the life of the new belt. With the front panel off, the drum may need to be supported by hand as it comes free — having a second person hold the drum steady makes this significantly easier and reduces the risk of scratching the drum or dropping it. Vacuum out accumulated lint while the cabinet is open. Place the new belt around the drum, seat it in the polished wear track left by the old belt, then route it around the idler pulley and around the motor pulley. Reinstall the motor mount, rotate the drum by hand to confirm the belt tracks straight and stays centered, then reassemble the front and rear panels. Restore power and run a short empty cycle listening for squeal or thump before loading it. Tools needed: nut driver or bit driver, open-end wrench, Phillips screwdriver, work gloves, and ideally a second person to support the drum.
Frequently Asked Questions
How do I confirm the belt is broken and not the motor?
With the dryer unplugged, open the door and try to spin the drum by hand. An intact belt gives firm resistance, because you're turning the motor and idler through the belt. If the drum coasts freely like a bicycle wheel, the belt is broken or has jumped off its pulleys. Sound is the other tell: with a broken belt the motor hums and the blower whooshes normally, so the dryer sounds like it's running perfectly while the drum sits still.
My belt broke and I noticed the idler pulley felt stiff. Do I need to replace that too?
Yes, strongly consider it. A worn or seized idler pulley is a well-documented cause of belt failure — if the pulley can't spin freely, it drags against the belt continuously instead of rolling with it, which wears through even a brand-new belt quickly. If your old belt broke and the pulley feels stiff, gritty, or doesn't spin smoothly when you turn it by hand, replace the idler pulley (part PS334244) along with the belt to avoid repeating this repair soon.
Is this the same length as your other Whirlpool dryer belt listings?
Not necessarily — Whirlpool uses different belt lengths across different dryer platforms even when the rib profile looks similar. This belt is approximately 97.75" long, which is specific to the large-capacity platform it's designed for. Always check your model number or measure your old belt's total length before ordering, since a belt of the wrong length will not seat and tension correctly.
Why does replacing this belt need two people?
On this large-capacity platform, accessing the belt often means removing the front panel and freeing the drum, which is heavy and can be awkward to support single-handedly while also working with your other hand. A second person holding the drum steady while you route the new belt reduces the risk of the drum shifting, scratching the finish, or being dropped. It's not strictly required, but it makes the job considerably easier.
Is this an OEM or aftermarket part?
This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured to match the approximately 97.75" length and rib profile of the original W10849499 / W10610882 belt used in compatible Whirlpool, Maytag, KitchenAid, Jenn-Air, and related large-capacity dryers.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
