Search results for "leveling"

XPARTCO 3390719 Dryer Thermal Fuse – Replaces WP3390719 – Compatible with Whirlpool, Maytag & Kenmore Dryers Product Description Restore safe dryer operation and proper heating with the XPARTCO 3390719 Dryer Thermal Fuse. This dryer Thermal Fuse is a replacement part for specific Whirlpool, Kenmore dryer models. This disposable, one-time fuse ensures safe operation of your appliance by cutting off power if the temperature exceeds safe limits. A bad thermal fuse can cause your appliance to stop functioning or prevent it from turning on altogether. Symptoms of a bad thermal fuse include no heat or a dryer that won't start. It is located on the blower housing and cannot be reset. XPARTCO is a trusted aftermarket brand offering appliance replacement parts built to OEM-equivalent specifications at a cost-effective price. Replaces Part Numbers WP3390719, 3390719, 15-198, 279650, 3389639, 3389640, 660877, 688841, 690198, 690798, 80004, ET402, G4AP0401, PD00002330, EAP11741444, AP6008309, PS11741444. Compatibility This replacement dryer thermal fuse fits select Whirlpool, Maytag, Kenmore, Amana, Estate, Roper, and Crosley dryers. Commonly installed on the blower housing or exhaust duct, depending on model. Always verify your dryer’s model number before ordering.Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement – Matches OEM safety and temperature ratings 🛡️ Overheat Protection – Shuts off power if unsafe temperatures are detected 🔥 Fixes No-Heat or No-Run Issues – Common solution for blown fuse symptoms 🧩 Direct-Fit Design – Installs easily without modification 💰 Cost-Effective Repair – Reliable alternative to OEM thermal fuses 📐 Product Specification Part Number: 3390719 Component Type: Dryer Thermal Fuse Function: One-time over-temperature safety cutoff Application: Blower housing or exhaust system Mounting: Screw-mounted Quality Level: Aftermarket replacement (not OEM) 🛠️ Installation Notes Tools Needed: Phillips screwdriver, nut driver ⚠️ Safety First: Unplug the dryer before servicing to avoid electrical shock. Basic Steps: Disconnect dryer power. Remove the rear or front access panel (model dependent). Locate the thermal fuse on the blower housing or exhaust duct. Disconnect wires and remove the old fuse. Install the new XPARTCO 3390719 thermal fuse. Reconnect wiring, reassemble panels, and restore power. Test dryer operation. ⏱️ Time Required: 15–20 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Aftermarket Appliance Parts 🔄 30-Day Return Policy Restore dryer safety and reliable operation — Add to Cart Now for a dependable, budget-friendly repair!

Read more less

XPARTCO WH11X34740 Washer Drain Pump Assembly – Compatible with GE & Hotpoint Washers Product Description Restore proper draining and reliable washer operation with the XPARTCO WH11X34740 Washer Drain Pump Assembly. This high-quality replacement pump is responsible for removing water from the washer during drain and spin cycles. A failing drain pump can cause standing water, slow draining, loud grinding noises, or error codes. Replacing it with this durable XPARTCO assembly helps ensure efficient water removal and dependable washing performance. XPARTCO is a trusted aftermarket brand offering appliance replacement parts built to OEM-equivalent specifications at a cost-effective price. Replaces Part Numbers WH23X25518, WH23X10038, WH23X25461, PD00079543, EAP16743374, AP7195487, PS16743374. Compatibility This replacement washer drain pump assembly fits select GE and Hotpoint washers. Example compatible models include (but are not limited to): GE GTW465ASNWW, GTW335ASNWW Hotpoint HTW240ASKWS Always verify your washer’s model number before ordering.Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement – Matches OEM fit and pumping performance 💧 Efficient Water Removal – Restores proper draining during cycles 🔇 Quiet Operation – Helps eliminate grinding or buzzing noises 💪 Durable Motor Construction – Designed for long service life 💰 Cost-Effective Repair – Reliable alternative to OEM drain pumps 📐 Product Specification Part Number: WH11X34740 Component Type: Washer Drain Pump Assembly Voltage: 120V AC Mounting: Direct-fit, bolt-on installation Application: Washer drain and spin system Quality Level: Aftermarket replacement (not OEM) 🛠️ Installation Notes Tools Needed: Phillips screwdriver, nut driver, pliers ⚠️ Safety First: Unplug the washer and shut off the water supply before servicing. Basic Steps: Disconnect washer power and water supply. Access the drain pump from the bottom or rear of the washer. Remove hoses and electrical connectors. Remove mounting screws and take out the old pump. Install the new XPARTCO WH11X34740 drain pump assembly. Reconnect hoses and wiring, reassemble panels, and restore power. Run a test cycle to confirm proper draining. ⏱️ Time Required: 25–35 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Aftermarket Appliance Parts 🔄 30-Day Return Policy Restore proper washer draining and prevent water buildup — Add to Cart Now for a dependable, budget-friendly repair!

Read more less

XPARTCO W10581874 Washer Drain Pump – Replaces WPW10581874 – Compatible with Whirlpool, Maytag & Kenmore Washers Product Description Restore proper water drainage and dependable washer performance with the XPARTCO W10581874 Washer Drain Pump. This high-quality aftermarket replacement pump removes wastewater during drain and spin cycles to prevent standing water and incomplete washes. A faulty drain pump can cause slow draining, loud humming or grinding noises, water remaining in the tub, or cycle interruptions. Replacing it with this reliable XPARTCO pump helps ensure smooth operation and restores efficient washing performance at a cost-effective price. XPARTCO offers trusted aftermarket appliance parts engineered to match original fit and function. Replaces Part Numbers WPW10581874, W10581874, 3449735, PD00028019, EAP10056668, AP6023189, PS11756530. Compatibility This replacement washer drain pump fits select Whirlpool, Maytag, Kenmore (Whirlpool-manufactured), Amana, Estate, and Roper washers. Common compatible models include (but are not limited to): Whirlpool WTW5000DW Maytag MVWB765FW Kenmore 110.25132411 Always verify your washer’s model number before ordering.Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement – Matches OEM fit and drainage performance 💧 Efficient Water Removal – Restores proper draining during cycles 🔇 Quiet, Smooth Operation – Helps eliminate excessive pump noise 💪 Durable Motor & Housing – Built for long service life 💰 Cost-Effective Repair – Affordable alternative to OEM drain pumps 📐 Product Specification Part Number: W10581874 Component Type: Washer Drain Pump Voltage: 120V AC Mounting: Direct-fit, bolt-on installation Application: Washer drain and spin system Quality Level: Aftermarket replacement (not OEM) 🛠️ Installation Notes Tools Needed: Phillips screwdriver, nut driver, pliers ⚠️ Safety First: Unplug the washer and shut off the water supply before servicing. Basic Steps: Disconnect washer power and water supply. Access the drain pump from the bottom or rear of the washer. Remove hoses and electrical connectors. Remove mounting screws and remove the old pump. Install the new XPARTCO W10581874 drain pump. Reconnect hoses and wiring, reassemble panels, and restore power. Run a test cycle to confirm proper draining. ⏱️ Time Required: 25–35 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Aftermarket Appliance Parts 🔄 30-Day Return Policy Restore proper washer draining and prevent water buildup — Add to Cart Now for a dependable, budget-friendly repair!

Read more less

XPARTCO WH23X29553 Washer Water Valve The XPARTCO WH23X29553 is an aftermarket replacement water inlet valve for GE front-load washers, and also fits select Hotpoint, RCA, Haier, Monogram, and Café models. This valve controls the flow of water into the washer from the household supply line — when the control calls for a fill, the valve's solenoid opens to admit water, and closes again once the correct level is reached. Built with an ABS plastic body and stainless steel components for durability against corrosion. Common failure causes include mineral or sediment buildup inside the valve body, a burned-out internal solenoid coil, and general wear over years of use. A failing valve typically shows up as the washer not filling properly, filling too slowly, or leaking water. It directly replaces AP6983554, PS12743643, EAP12743643, 33090202, and 0024000126GA. As an aftermarket replacement, the WH23X29553 is built to OEM-equivalent quality standards. Quick Answer The XPARTCO WH23X29553 Washer Water Valve fixes GE front-load washers (and select Hotpoint, RCA, Haier, Monogram, and Café models) that aren't filling properly, are filling too slowly, or are leaking water near the valve connections. Replaces AP6983554, PS12743643, EAP12743643, 33090202, 0024000126GA. Not the same part as the similarly-numbered WH23X29538 valve — confirm you have the correct number before ordering. Common Problems This Part Fixes Washer not filling with water, or filling only partially Washer fills much more slowly than it used to Water leaking near the valve connections Cycle stalling at the fill step and never advancing to wash No hot water reaching the tub, or no cold water reaching the tub Washer not washing properly due to insufficient or incorrect-temperature water Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer water inlet valve directly replaces the following OEM and cross-reference part numbers: WH23X29553, 33090202, C-491/20-A13, AGE26162, AP6983554, EAP12743643, PD00067381, PS12743643 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This water valve is compatible with select GE front-load washers, and also fits select Hotpoint, RCA, Haier, Monogram, and Café washers built on the GE platform, including model numbers such as: GFW650SPN0SN, GFW650SPN1SN, GFW650SPN2SN, GFW650SPN3SN, GFW650SPN4SN GFW650SSN0WW, GFW650SSN1WW, GFW650SSN2WW, GFW650SSN3WW, GFW650SSN4WW GFW850SPN0DG, GFW850SPN0RS, GFW850SPN1DG, GFW850SPN1RS, GFW850SPN2DG, GFW850SPN2RS, GFW850SPN3DG, GFW850SPN3RS, GFW850SPN4RS, GFW850SPN5RS GFW850SSN0WW, GFW850SSN1WW, GFW850SSN2WW, GFW850SSN3WW GFW655SSV0WW PFW870SPV0RS PFW950SPT0DS, PFW950SPT1DS, PFW950SPT2DS Note — not the same as WH23X29538: A similarly-numbered valve, WH23X29538, is a separate part (replaces 4977241, AP6990115, PS16217225, EAP16217225, 33090201, 0024000126GB) used on related but distinct models. The two are easy to confuse given how close the numbers are — always confirm you have the exact part number from your appliance or parts diagram before ordering. Contact our support team with your model number if you're unsure. Key Features Aftermarket replacement built to match GE's factory-specified solenoid design and flow rate ABS plastic body with stainless steel components for corrosion resistance Resolves "won't fill," "fills slowly," and "leaking near the valve" symptoms caused by valve failure Direct drop-in replacement — matches the original mounting and hose connections Replaces AP6983554, PS12743643, EAP12743643, 33090202, and 0024000126GA Compatible with GE, Hotpoint, RCA, Haier, Monogram, and Café front-load washers Aftermarket replacement built to OEM-equivalent quality standards Product Specifications Part Number XPWH23X29553 Part Type Washer Water Inlet Valve OEM Part Number WH23X29553 Condition Aftermarket Replacement Brand GE Application Front-Load Washers Body Material ABS plastic Component Material Stainless steel Quantity 1 valve Compatible Brands GE, Hotpoint, RCA, Haier, Monogram, Café Installation Notes ⚠️ Shut Off Water Supply And Unplug Washer Before Starting — Release The Control Panel Carefully Disconnect power at the outlet or shut off the circuit breaker, and shut off both hot and cold water supply valves before beginning. Wear work gloves. Access to this valve is typically behind the front control panel on many models. When removing the front control panel, avoid pulling it straight out too far — slotted tabs on the right side of the panel can break if forced. Instead, pull the panel gently forward, then slide it to the right to release it cleanly. With the panel released, locate the valve and disconnect the hot and cold water supply hoses, keeping a towel handy for residual water. Photograph the wiring and hose connections before disconnecting anything. Disconnect the electrical connector and the outlet hoses from the old valve, remove its mounting screws, and pull it free. Install the new WH23X29553 in the same position, reconnect all outlet hoses to their original positions, reconnect the electrical connector, and secure the mounting screws. Reattach the hot and cold supply hoses, tightening securely. Reinstall the control panel and any surrounding trim, restore the water supply, and check every connection for leaks before restoring power. Run a full test cycle across a few different temperature settings to confirm each fill function works correctly. Tools needed: Phillips screwdriver, pliers, towel, work gloves. Frequently Asked Questions How do I remove the front control panel without breaking it? Avoid pulling the panel straight out with heavy force — the slotted tabs on the right side of the panel can snap if you pull too far. Instead, pull the panel gently forward first, then slide it to the right to release it from its mounting. This gentler approach avoids the most common way this panel gets damaged during a valve repair. I've heard this valve sometimes needs replacing again after just a couple of years. Is that normal? Some owners have reported needing to replace this valve again within a relatively short time, even after a successful repair. While most installations hold up well long-term, if you experience a repeat failure, it's worth double-checking your household water pressure and mineral content, since hard water and high pressure can accelerate wear on any water valve regardless of brand. Is this the same as WH23X29538? The numbers look almost identical. No, these are two separate GE valve part numbers with different cross-reference sets, despite the similar numbering. Always confirm the exact part number from your washer's parts diagram or the sticker on your old valve rather than assuming based on a close match, since ordering the wrong one means it won't fit correctly. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine GE OEM part, but is manufactured to match the solenoid design, flow rate, and connection type of the original WH23X29553 valve used in compatible GE, Hotpoint, RCA, Haier, Monogram, and Café front-load washers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

AJU75152606 Genuine OEM LG Washer Water Inlet Valve Assembly The AJU75152606 is a genuine LG OEM water inlet valve assembly for LG top-load agitator washing machines. This assembly connects to the washer's hot and cold water supply and controls the flow of water into the tub during the fill portion of the wash and rinse cycles — electrical signals from the control system open and close the appropriate water passage, filling the tub to the correct level and shutting off once it's reached. This electric-powered valve assembly is finished in gray, designed for freestanding installation, and rated for an 8 lb capacity washer. Common causes of failure include mineral buildup or debris restricting flow through the valve, or general electrical wear in the solenoid coils. Symptoms of a failing valve include the washer not filling with water, hose leaks at the connections, the valve not opening fully, or reduced flow rate from internal buildup. Replacing this assembly requires removing the control panel and main top of the washer — a moderate difficulty repair. It directly replaces AP7005965. Quick Answer The AJU75152606 Genuine OEM LG Washer Water Inlet Valve Assembly fixes LG top-load agitator washers that won't fill with water, are leaking at the hose connections, or have reduced flow from internal buildup. Gray, electric-powered, 8 lb capacity rating. Replaces AP7005965. Not the same as the similarly-numbered AJU75152602 valve, which is used on different LG WT7000-series models — confirm your exact part number before ordering. Common Problems This Part Fixes Washer not filling with water Hose leaks at the valve connections Valve not opening fully, restricting water flow Reduced flow rate from mineral buildup or debris Overflow or filling problems from inconsistent water pressure Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers AJU75152606, ALG53799, AP7005965, EAP16547657, PD00074631, PS16547657 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This water inlet valve assembly is compatible with select LG top-load agitator washing machines, including model numbers such as WT7000CW, WT7005CW, WT6100CW, WT6105CM, WT6105CW, T14A4SEHTW, T1490SEHTW, T15A4SEHT2, T1590SEHTW, T15A4SEHTW, T14A4SEHTC, T1490SEHTC, and T14A4SEHBW. Note — not the same as AJU75152602: A similarly-numbered valve, AJU75152602, is a separate part used on other LG WT7000-series models (WT7100CW, WT7150CW, WT7300CV, WT7300CW, WT7400CW, WT7400CV, WT7405CV, WT7405CW, WT7800CW, WT7800CV, WT7900HBA, WT7155CW). The two numbers are easy to confuse given how close they are — always confirm the exact part number from your appliance or parts diagram before ordering. Contact our support team with your model number if you're unsure which valve your washer needs. Key Features Genuine LG OEM part — factory-specified solenoid design and flow rate Regulates hot and cold water flow into the tub during fill Resolves "won't fill," "hose leaks," "valve not opening fully," and "reduced flow" symptoms caused by valve failure Electric-powered, gray finish Designed for freestanding installation Rated for 8 lb capacity washers Direct drop-in replacement — matches the original mounting and hose connections Replaces AP7005965 Compatible with LG top-load agitator washing machines Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number AJU75152606 Part Type Washer Water Inlet Valve Assembly Condition Genuine OEM Brand LG Application Top-Load Agitator Washing Machines Color Gray Power Type Electric Installation Type Freestanding Capacity Rating 8 lb Repair Difficulty Moderate — requires control panel and main top removal Quantity 1 valve assembly Compatible Brand LG Installation Notes ⚠️ Unplug Washer And Shut Off Water Supply Before Starting Disconnect power at the outlet or shut off the circuit breaker, and shut off the water supply before beginning. Wear work gloves. Remove the washer's control panel and main top to access the inlet valve — this is a moderate difficulty repair due to the disassembly involved. Photograph the wiring and hose connections before disconnecting anything. Disconnect the water hoses and wiring connectors from the old valve. Unscrew and remove the old inlet valve assembly. Position the new AJU75152606 in the same location and secure it with screws. Reconnect the water hoses and wiring connectors fully. Reassemble the main top and control panel. Restore the water supply and power, then run a test cycle to confirm the washer fills correctly with no leaking at the hose connections. Tools needed: Phillips screwdriver, pliers, work gloves. Frequently Asked Questions My washer isn't filling with water. Is this the right part? Yes, this is the most direct symptom of a failed water inlet valve. Since this valve is what admits water from your household supply into the washer, a solenoid failure, mineral buildup, or debris can prevent water from entering properly, stopping the wash cycle from proceeding. Is this the same as AJU75152602? No, these are two separate LG valve part numbers used on different washer model series, despite the similar numbering. Always confirm the exact part number from your washer's parts diagram or the sticker on your old valve rather than assuming based on a close number match. Is this a difficult repair? It's a moderate difficulty repair, since it requires removing the washer's control panel and main top to access the valve. Basic hand tools are sufficient, but budget more time than you would for a simpler part swap. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by LG to factory specifications — guaranteed fit, materials, and performance. It matches the original solenoid design, flow rate, and connection type of the water inlet valve originally installed in your washer. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO WH13X10031 Washer Water Inlet Valve The XPARTCO WH13X10031 is an aftermarket replacement water inlet valve for GE washer/dryer combo units, and also fits select Hotpoint and Kenmore combo models. This valve controls the flow of water into the washer side of the combination unit, opening to admit hot and cold water as the cycle calls for it and closing once the correct fill level is reached. Made of durable metal construction for long-term reliability. Rated 115V. Common failure causes include mineral or sediment buildup inside the valve body and general electrical wear in the solenoid coils. A failing valve produces a clear set of symptoms: the washer side not filling properly, water continuing to enter the machine even when it's turned off, or leaking near the valve connections. Quick Answer The XPARTCO WH13X10031 Washer Water Inlet Valve fixes GE washer/dryer combo units (and select Hotpoint and Kenmore combo models) that aren't filling properly, or where water continues entering the machine even when it's turned off. 115V, metal construction. This is a combo washer/dryer unit valve — a different application from a standalone top-load or front-load washer valve. Confirm your unit type before ordering. Common Problems This Part Fixes Washer side of the combo unit not filling with water properly Water continuing to enter the machine even when it's turned off Leaking near the valve connections Cycle stalling at the fill step and never advancing to wash No hot water reaching the tub, or no cold water reaching the tub Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers WH13X10031, 1264513, AGE1189086, AP3995207, PS1482394. We were not able to confirm additional cross-reference or superseding part numbers for this specific part from reliable sources at the time this page was built, so none are listed here rather than guessed. If you have a cross-reference number for your appliance, contact our support team and we will verify compatibility before you order. Compatibility This water inlet valve is compatible with select GE washer/dryer combo units, and also fits select Hotpoint and Kenmore combo models built on the GE platform. Note — combo unit valve, not a standalone washer valve: This valve is specifically designed for washer/dryer combo units. GE also sells several similarly-numbered valves for standalone top-load and front-load washers, including WH13X10015, WH13X10030, WH13X10033, and WH13X10037 — these are separate parts for different platforms and are not interchangeable with this combo unit valve. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure which valve your appliance needs. Key Features Aftermarket replacement water inlet valve for GE washer/dryer combo units Resolves "won't fill properly" and "water continues entering when off" symptoms caused by valve failure Rated 115V Durable metal construction Direct drop-in replacement — matches the original mounting and hose connections Compatible with GE, Hotpoint, and Kenmore washer/dryer combo units Aftermarket replacement built to OEM-equivalent quality standards Product Specifications Part Number WH13X10031 OEM Part Number WH13X10031 Part Type Washer/Dryer Combo Water Inlet Valve Condition Aftermarket Replacement Application Washer/Dryer Combo Units Voltage 115V Material Metal Quantity 1 valve Compatible Brands GE, Hotpoint, Kenmore Installation Notes ⚠️ Shut Off Water Supply And Unplug The Unit Before Starting Disconnect power at the outlet or shut off the circuit breaker, and shut off both hot and cold water supply valves before beginning. Wear work gloves. Access to the valve on combo units typically requires removing a front or rear access panel — check your model's service diagram, since access varies more on combo units than on standalone washers. Photograph the wiring and hose connections before disconnecting anything. Disconnect the water supply lines from the old valve, disconnect the electrical connector, and remove the mounting screws holding it in place, then pull the valve free. Install the new WH13X10031 in the same position, reconnect all hose connections to their original positions, reconnect the electrical connector fully, and secure the mounting screws. Reattach the hot and cold supply lines, tightening securely. Restore the water supply and check every connection for leaks before restoring power. Run a full test cycle to confirm the washer side fills correctly with no leaking. Tools needed: Phillips screwdriver, pliers, work gloves. Frequently Asked Questions Is this the right valve for my standalone washer, or only for a combo unit? This valve is designed specifically for GE washer/dryer combo units, where the washer and dryer are built into a single appliance. If you have a standalone washer, this is not the correct valve — GE uses several other similarly-numbered valves, such as WH13X10015, WH13X10030, WH13X10033, and WH13X10037, for standalone top-load and front-load washers. Confirm your unit type and model number before ordering. Water keeps entering my machine even when it's off. Is this the valve? Yes, this is a documented symptom of a failing water inlet valve. If the internal solenoid is stuck open or has worn out, water can continue to flow into the machine even after it's been turned off, since the valve can no longer fully seal. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine GE OEM part, but is manufactured to match the voltage rating, solenoid design, and connection type of the original WH13X10031 valve used in compatible GE, Hotpoint, and Kenmore washer/dryer combo units. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

W10240513 Washer Lid Lock Strike – Replaces WPW10240513 – Compatible with Whirlpool, Maytag & Kenmore Washers Product Description Restore proper lid locking function with the W10240513 Washer Lid Lock Strike. This replacement part attaches to the washer lid and engages with the lid lock assembly to ensure the washer detects when the lid is closed and can safely begin operation. A damaged or broken lid strike can prevent the washer from starting, cause lid lock errors, or stop the spin cycle. Replacing it with this durable replacement part restores proper lid engagement and ensures smooth washer operation. This part is designed to match original fit and function for reliable performance. Replaces Part Numbers WPW10240513, W10240513, AWP50167, PD00004624, 1873013, 045900191755, EAP11750882, AP6017583, PS11750882. Compatibility This replacement washer lid lock strike fits select Whirlpool, Maytag, Kenmore (Whirlpool-manufactured), Amana, and Roper washers. Common compatible models include (but are not limited to): Whirlpool WTW5000DW Maytag MVWC565FW Kenmore 110.22352510 Always verify your washer’s model number before ordering.Contact our support team if you’re unsure. ✅ Key Features 🔄 Direct Replacement Part – Matches OEM fit and function 🔒 Ensures Proper Lid Lock Engagement – Works with lid lock assembly ⚙️ Fixes Common Issues – Resolves lid lock errors and start failures 🧩 Simple Installation – Attaches easily to washer lid 💰 Cost-Effective Repair – Affordable solution for lid lock problems ⚠️ Symptoms If your washer is experiencing any of the following issues, this part may need replacement: ❌ Washer will not start 🔒 Lid not locking properly ⚠️ Lid lock error codes 🔄 Cycle won’t begin or stops mid-cycle 🛑 Washer won’t spin Replacing this lid strike can restore proper lid locking and washer operation. 📐 Product Specification Part Number: W10240513 Component Type: Washer Lid Lock Strike Material: Durable molded plastic Application: Lid lock engagement system Mounting: Snap-in or screw-mounted (model dependent) Quality Level: Aftermarket replacement 🛠️ Installation Notes Tools Needed: Screwdriver (if required) ⚠️ Safety First: Unplug the washer before servicing to avoid electrical shock. Basic Steps: Disconnect washer power. Locate the lid strike on the washer lid. Remove the damaged strike. Install the new W10240513 strike in place. Ensure proper alignment with the lid lock assembly. Restore power and test operation. ⏱️ Time Required: Under 10 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Appliance Replacement Parts 🔄 30-Day Return Policy Restore proper lid locking and washer performance — Add to Cart Now for a quick and easy fix!

Read more less

WD21X25468 Genuine OEM GE Dishwasher Pressure Sensor Assembly The WD21X25468 is a Genuine OEM GE replacement dishwasher pressure sensor assembly compatible with a wide range of GE, GE Profile, GE Café, Hotpoint, Haier, and Monogram dishwashers in the GDF, GDT, GDP, PDT, CDT, ZDT, QDP, and HDF series. The pressure sensor monitors water pressure inside the dishwasher tub during fill and drain cycles and sends real-time readings to the electronic control board. The control board uses these readings to calculate the correct amount of water needed for each wash cycle and to confirm that the tub has drained properly before advancing to the next cycle phase. When the pressure sensor fails — or when it becomes clogged with grease, food residue, or mineral buildup — the dishwasher may not fill with water, may overfill, may stop mid-cycle, may fail to drain correctly, or may display error codes H2O or FTD (Failure to Drain). This Genuine OEM part is manufactured by GE to factory specifications. It directly replaces AP6976524, PS12741258, EAP12741258, 4962334, 37640602, and 265D3356P001. Sold individually. Installs in 15–20 minutes — a screwdriver is the only tool required for most models. Quick Answer The WD21X25468 Genuine OEM GE Dishwasher Pressure Sensor Assembly fixes GE dishwashers displaying error codes H2O or FTD (Failure to Drain), not filling with water, overfilling, stopping mid-cycle, or running excessive noise from the spray arms. Monitors water level and pressure — signals the control board to fill, wash, and drain correctly. Genuine OEM. Replaces AP6976524, PS12741258, EAP12741258, 4962334, 37640602, 265D3356P001. Sold individually. Compatible with GE GDF, GDT, PDT, CDT, ZDT, QDP, HDF, and related series. Common Problems This Part Fixes Error code H2O displayed — dishwasher not receiving enough water or no water at all Error code FTD (Failure to Drain) displayed — sensor not confirming tub has drained Dishwasher not filling with water when a cycle is started Dishwasher overfilling — sensor not signaling the control board to stop filling Dishwasher stopping mid-cycle without completing the wash Excessive noise during operation — sensor not accurately controlling spray arm water pressure Dishwasher requires priming with water to start (filling the tub manually before it will run) Replaces Part Numbers This pressure sensor directly replaces the following OEM and cross-reference part numbers: WD21X25468, 265D3356P001, AGE24772, AP6976524, EAP12741258, OEM20929581, PD00067609, PS12741258. Contact our support team with your model number if you need confirmation before ordering. Compatibility This pressure sensor is compatible with a wide range of dishwashers from the following GE product lines: GE dishwashers — GDF450, GDF510, GDF511, GDF535, GDF550, GDF565, GDF570, GDF630, GDF640, GDF645 series GE dishwashers — GDT530, GDT535, GDT565, GDT580, GDT605, GDT625, GDT630, GDT635, GDT645, GDT695 series GE dishwashers — GDP615, GDP645, GDP665 series GE Profile dishwashers — PDT715, PDT775, PDT785 series GE Café dishwashers — CDT800, CDT875 series GE Monogram dishwashers — ZDT800, ZDT870, ZDT925, ZDT985 series Hotpoint dishwashers — HDF310, HDF330 series Haier dishwashers (select GE-platform models) GE / Café / Profile — QDP555 series Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Genuine OEM part manufactured by GE to factory specifications — guaranteed fit and performance Monitors water pressure inside the tub throughout fill and drain cycles — signals the control board to fill to the correct level and confirm complete drainage Resolves H2O and FTD error codes on compatible GE dishwashers Sensor can also fail due to grease or mineral buildup blocking the pressure port — cleaning may resolve the issue without replacement Replaces AP6976524, PS12741258, EAP12741258, 4962334, 37640602, and 265D3356P001 Compatible with GE GDF, GDT, GDP, PDT, CDT, ZDT, QDP, HDF, and Hotpoint dishwasher series Sold individually Quick DIY repair — installs in 15–20 minutes with a screwdriver Product Specifications Part Number WD21X25468 Part Type Dishwasher Pressure Sensor Assembly (Pressure Switch) Condition Genuine OEM Application GE, GE Profile, GE Café, GE Monogram, Hotpoint, Haier Dishwashers Function Monitors tub water level and pressure — signals control board for fill and drain control Error Codes Resolved H2O (no/low water), FTD (Failure to Drain) Sold As Single sensor assembly Compatible Brands GE, GE Profile, GE Café, GE Monogram, Hotpoint, Haier Installation Notes ⚠️ Unplug Dishwasher and Shut Off Water Before Starting Disconnect power and shut off the water supply before beginning. On most compatible GE models, the pressure sensor is located near the bottom of the dishwasher tub, accessible after removing the lower front kick panel (secured by one or two screws). The sensor assembly connects to a small hose and a wiring harness connector. Tip: before replacing the sensor, remove it and inspect the pressure port and hose for grease, food residue, or mineral buildup — a clogged sensor port can cause H2O and FTD errors without the sensor itself being electrically failed. Clean the port and hose with warm water and a small brush, reinstall, and test the dishwasher. If the error codes persist after cleaning, replace the WD21X25468 sensor. To replace: disconnect the hose and wiring harness from the old sensor, unclip or unscrew the sensor from its mounting bracket, and install the new sensor in the same position. Reconnect the hose and harness, restore power and water, and run a test cycle. Tools needed: Phillips screwdriver. Frequently Asked Questions What does the dishwasher pressure sensor do? The pressure sensor monitors the water pressure — and therefore the water level — inside the dishwasher tub throughout the wash cycle. It sends continuous readings to the electronic control board, which uses the data to determine how much water to add during fill, when to stop filling, and whether the tub has drained completely before advancing to the next cycle phase. An accurate pressure sensor is essential for the dishwasher to fill to the correct level (not too much, not too little), wash with the correct spray arm pressure, and drain fully before moving on to rinse or dry cycles. What do error codes H2O and FTD mean on GE dishwashers? H2O error code on compatible GE dishwashers indicates that the dishwasher is not detecting enough water in the tub — either water is not filling at all, or the pressure sensor is not sensing the water that has filled. FTD (Failure to Drain) code indicates the dishwasher has not confirmed that the tub has drained within the expected time. Both codes can be caused by a faulty pressure sensor, a clogged sensor port, a failed fill valve, a blocked drain system, or control board issues. The pressure sensor should be inspected and tested first since it is the most accessible and commonly replaced component for these two error codes. Should I try cleaning the sensor before replacing it? Yes — absolutely. The pressure sensor on GE dishwashers can produce H2O and FTD error codes when its pressure port or connected hose becomes clogged with grease, food residue, or hard water mineral deposits — even if the sensor itself is electrically intact. Before ordering a replacement, remove the sensor, inspect the pressure port opening, and clean it thoroughly with warm water and a small brush. Flush the connected hose to clear any buildup. Reinstall and run a test cycle. If the error codes return, the sensor has electrically failed and needs replacement with the WD21X25468. My dishwasher won't fill unless I pour water in manually first — is this the pressure sensor? Yes — this is a classic symptom of a clogged or failed pressure sensor. When the sensor port is blocked, the sensor reads zero pressure (empty tub) even when the dishwasher starts. In some cases the control board interprets this as a drainage confirmation and will not initiate the fill cycle. Pouring water into the filter manually raises the physical water level enough to trigger filling. Check and clean the sensor port as described above. If cleaning does not resolve the issue, replace the WD21X25468 sensor. Is this a Genuine OEM or aftermarket part? This is a Genuine OEM part manufactured by GE to factory specifications. It is the exact same pressure sensor assembly installed in compatible GE, GE Profile, GE Café, Hotpoint, and related brand dishwashers from the factory — guaranteed fit, materials, and performance. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

WH13X10029 Genuine OEM GE Washer Water Valve The WH13X10029 is a genuine GE OEM water inlet valve for GE, Hotpoint, Haier, Monogram, and Café front-load washers. This is a 2-inlet, 3-outlet valve assembly built around three internal solenoids: two work together during the wash portion of the cycle, opening in different combinations depending on the wash temperature you select, while the third solenoid handles the dedicated cold-only rinse. Because three separate solenoids share one valve body, a failure in any single one of them can affect only part of your washer's fill behavior while the rest continues working normally. Rated 120V, 60Hz, and measuring approximately 5-3/8"L x 3-1/8"W x 2-1/2"H, this valve ships as a complete 3-solenoid assembly with its mounting bracket included. Common failure symptoms include the washer continuing to fill after it should have stopped, slow filling, or a complete failure to fill on one specific water temperature setting while others work fine. It directly replaces AP4303282, WV10029, 33090039, 1475762, AH1482392, EA1482392, EAP1482392, PD00001515, and PS1482392. As a genuine OEM part, the WH13X10029 is manufactured by GE to factory specifications — guaranteed fit, materials, and performance. Quick Answer The WH13X10029 Genuine OEM GE Washer Water Valve fixes GE, Hotpoint, Haier, Monogram, and Café front-load washers that won't shut off after filling, fill slowly, or won't fill on a specific temperature setting (such as cold-only rinse) while other settings work fine. 2-inlet, 3-outlet, 3-solenoid valve assembly with mounting bracket, 120V, 60Hz, 5-3/8"L x 3-1/8"W x 2-1/2"H. Replaces AP4303282, WV10029, 33090039, 1475762, AH1482392, EA1482392, EAP1482392, PD00001515, PS1482392. Genuine OEM — manufactured by GE to factory specifications for guaranteed fit, materials, and performance. Common Problems This Part Fixes Washer keeps filling and won't shut off, even after reaching the correct level Washer fills much more slowly than it used to Washer won't fill at all on one specific temperature setting while other settings work normally Cold-only rinse cycle failing to fill while wash-cycle fills work fine (or vice versa) Cycle stalling at the fill step and never advancing to wash Water leaking or dripping near the valve connections Washer stopping mid-cycle due to a fill-related fault Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer water valve directly replaces the following OEM and cross-reference part numbers: WH13X10029, 33090039, PD00001515, EAP1482392, AGE26067, AH1482392, EA1482392, AP4303282, PS1482392. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This water valve is compatible with select GE, Hotpoint, Haier, Monogram, and Café front-load washers, including model families such as GFA, GFW, GMA, and WBV, and specific models such as GFWS1600H, GFWS1605H, GFWS1700H, and GFWS1705H. Note: This valve is specific to GE's front-load washer platform. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Genuine GE OEM part — factory-specified solenoid design and flow-rate calibration Complete 3-solenoid water valve assembly — 2 inlets (hot and cold), 3 outlets Two solenoids manage the wash-cycle fill combinations by temperature selection; a third handles cold-only rinse Resolves "won't shut off," "fills slowly," and "won't fill on a specific temperature setting" symptoms caused by valve failure Includes the mounting bracket — no need to transfer hardware from the old valve Rated 120V, 60Hz Approximately 5-3/8"L x 3-1/8"W x 2-1/2"H Direct drop-in replacement — matches the original mounting and hose connections Replaces AP4303282, WV10029, 33090039, 1475762, AH1482392, EA1482392, EAP1482392, PD00001515, and PS1482392 Compatible with GE, Hotpoint, Haier, Monogram, and Café front-load washers Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number WH13X10029 Condition Genuine OEM Part Type Washer Water Inlet Valve (2-In / 3-Out, 3-Solenoid) Brand GE Application Front-Load Washers Voltage 120V Frequency 60 Hz Inlets 2 (hot and cold) Outlets 3 Solenoids 3 (one double, one single, one dedicated cold-rinse) Dimensions 5-3/8"L x 3-1/8"W x 2-1/2"H Kit Contents Valve assembly + mounting bracket Quantity 1 valve assembly Compatible Brands GE, Hotpoint, Haier, Monogram, Café Installation Notes ⚠️ Shut Off Water Supply And Unplug Washer Before Starting — Stackable Units May Need A Second Person Disconnect power at the outlet or shut off the circuit breaker, and shut off both hot and cold water supply valves before beginning. Wear work gloves. If your washer is part of a stacked laundry center, the dryer sitting on top will need to be removed first to access the top of the washer — this is much easier with a second person helping to lift and support the dryer safely. Remove the screws securing the top panel of the washer, then slide the panel back and lift it off to access the valve assembly. Disconnect the hot and cold water supply hoses from the back of the valve, keeping a towel handy for residual water. Photograph the wiring and hose connections before disconnecting anything, since this valve has multiple solenoids and outlet hoses that must be reconnected in the correct positions. Disconnect the electrical connectors and the three outlet hoses from the old valve, then remove its mounting screws and pull it free along with its bracket. Install the new WH13X10029 assembly in the same position, reconnect all three outlet hoses to their original positions, reconnect the electrical connectors, and secure the mounting screws. Reattach the hot and cold supply hoses, tightening securely. Reinstall the top panel, restore the water supply, and check every connection for leaks before restoring power. Run a full test cycle across a few different temperature settings, including a cold-only rinse if your washer has one, to confirm each solenoid is filling and shutting off correctly. If this is a stackable unit, carefully reposition the dryer back on top once testing is complete. Tools needed: Phillips screwdriver, pliers, towel, work gloves, and a helper for stackable units. Frequently Asked Questions My washer won't shut off and keeps filling. Is that this valve? Yes, this is one of the most common symptoms of a failing valve on this platform. A worn internal seal on one of the three solenoids can fail to close fully, letting water continue flowing even after the correct fill level is reached. Since this could lead to overflow, it's worth shutting off the water supply at the wall if you notice this happening rather than waiting to address it. Only my cold-only rinse doesn't fill, but regular wash cycles work fine. Do I need the whole valve? Yes. This valve houses three separate solenoids in one assembly — two that combine for wash-cycle fills at different temperatures, and one dedicated specifically to the cold-only rinse. If just one of those three has failed, the others can continue working normally, which is exactly why a single-cycle fill problem can appear alongside otherwise normal operation. The three solenoids aren't sold or serviced individually, so replacing the complete assembly is the correct repair even if only one function is affected. Do I really need to remove the dryer if this is a stacked unit? On most stacked laundry centers, yes — the top panel of the washer sits underneath the dryer, so the dryer needs to come off first to get access. This is a heavier, more awkward step than the rest of the repair, so it's worth having a second person help lift and support the dryer safely rather than attempting it alone. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by GE to factory specifications — guaranteed fit, materials, and performance. It includes the same 3-solenoid design, flow rate, and mounting configuration as the water valve originally installed in your front-load washer. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO AEZ73293801 Cooktop Burner Control Knob – Compatible with LG & Kenmore Cooktops Product Description Restore smooth, precise burner control with the XPARTCO AEZ73293801 Cooktop Burner Control Knob. This high-quality aftermarket replacement knob fits securely onto the burner control shaft, allowing accurate flame adjustment and dependable operation. A cracked, loose, or missing knob can make it difficult to control heat or safely operate your cooktop. Replacing it with this durable XPARTCO knob restores proper functionality and everyday cooking convenience. XPARTCO is a trusted aftermarket brand offering appliance replacement parts built to OEM-equivalent specifications at a cost-effective price. Replaces Part Numbers AEZ73293801, EBZ60710601, 2025031, PD00055975, EAP3639420, AH3639420, EA3639420, AP5594929, PS3639420. Compatibility This replacement cooktop burner control knob fits select LG and Kenmore (LG-manufactured) gas cooktops and ranges. Commonly used on surface burner controls. Always verify your appliance’s model number before ordering.Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement – Matches original fit and appearance 🎛️ Smooth Flame Control – Restores accurate burner adjustment 🧩 Direct-Fit Design – Push-on installation for secure seating 💪 Durable Plastic Construction – Built for daily kitchen use 💰 Cost-Effective Repair – Affordable alternative to OEM knobs 📐 Product Specification Part Number: AEZ73293801 Component Type: Cooktop Burner Control Knob Material: High-strength molded plastic Color: Black (OEM-style) Mounting: Push-on / shaft-fit Application: Gas cooktop or range burner control Quality Level: Aftermarket replacement (not OEM) 🛠️ Installation Notes Tools Needed: None ⚠️ Safety First: Ensure the cooktop or range is turned off and cool before installing the knob. Basic Steps: Turn the burner control to the OFF position. Align the new XPARTCO AEZ73293801 knob with the control shaft. Press firmly until fully seated. Rotate to confirm smooth operation. ⏱️ Time Required: Under 2 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Aftermarket Appliance Parts 🔄 30-Day Return Policy Restore safe, precise burner control in seconds — Add to Cart Now for a quick, budget-friendly fix!

Read more less

3148953CM Surface Burner Infinite Switch 240V, 7.5-9.3A switch for 8" elements. Fits specific Whirlpool electric ranges. Replaces Part Numbers: WP3148953, 3148953, 492439, AP6007658, PS11740775, WP3148953VP. Description The Infinite Control Switch is a replacement part for specific Whirlpool ranges and cooktop models. This part allows for precise adjustment of the heat level, enabling users to achieve the perfect temperature for various cooking techniques, from simmering to boiling. Causes of a bad Infinite Control Switch can range from electrical issues, such as short circuits or worn contacts, to mechanical failures within the switch itself.   This is an aftermarket part that can be used as a replacement for the OEM part. California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

WB24X25013 Genuine OEM GE Range Surface Burner Infinite Switch Replaces WB24X47186. The WB24X25013 is a genuine GE OEM infinite control switch for a dual (bridge) surface element on GE, Hotpoint, and select Kenmore electric ranges — the kind of burner with an inner coil and an outer coil that can be run together for a large pot or as the inner coil alone for a small pan. Because it's governing two coil zones instead of one, this switch uses six terminal connections rather than the three or four found on a standard single-element infinite switch, and it mounts to the control panel with a distinctive figure-8 style shaft and two female mounting holes. Like any infinite switch, it doesn't have fixed heat positions — instead it rapidly cycles power to the element(s) on and off at a ratio set by the knob, giving continuous heat adjustment from warm to high rather than a handful of steps. Rated for 240VAC at 15 amps. Over years of cycling, the internal contacts on a switch like this wear, pit, or weld together, and boilovers or spills can corrode the switch body and cause it to fail. A worn switch on a dual-element burner can produce an unusually wide symptom set: the whole burner may fail, or just the outer ring may stop responding while the inner coil still works, or the burner may stay on continuously regardless of the knob position. It directly replaces WB24X47186, 191D4774P005, AP5999509, PS11729102, EAP11729102, and 4464832. As a genuine OEM part, the WB24X25013 is manufactured by GE to factory specifications — guaranteed fit, materials, and performance. Quick Answer The WB24X25013 Genuine OEM GE Range Surface Burner Infinite Switch fixes GE, Hotpoint, and Kenmore electric ranges with a dual (bridge) element burner where the burner won't turn on or off, only the outer ring fails to work while the inner coil still heats, the burner stays on continuously, or heat can't be adjusted. Six-terminal switch, figure-8 shaft, 240VAC / 15A. Replaces WB24X47186, 191D4774P005, AP5999509, PS11729102, EAP11729102, 4464832. Not the same switch as a standard single-element infinite switch — this one is specific to dual/bridge burners with an inner and outer coil. Common Problems This Part Fixes Dual-element burner won't turn on at all when the knob is turned Outer ring of a dual/bridge element won't activate while the inner coil still works Burner won't turn off — stays hot even with the knob at the off position Burner stuck at one heat level regardless of where the knob is set No ability to adjust temperature — always full blast or always low Intermittent burner operation — works sometimes, not others Knob feels loose, gritty, or doesn't turn smoothly through its range Burner failure that followed a boilover or liquid spill on the control panel Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This range surface burner infinite switch directly replaces the following OEM and cross-reference part numbers: WB24X25013, WB24X47186, 191D4774P005, AGE1543754, AP7216136, PS11729102, PS17872685, EAP11729102, 4464832, 191D4774P005, MDSA-W767-GEM If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This dual-element infinite switch is compatible with select GE, Hotpoint, and Kenmore electric ranges equipped with a dual (bridge) surface element, including model families such as: GE JB6, JB7, and JB8 series electric ranges (including JB630, JB640, JB645, and JB655) GE JBS series electric ranges GE JS6 and JS7 series electric ranges (including the JS760 series) GE GRS and GRF series electric ranges Hotpoint electric ranges (select GE-built models) Select Kenmore electric ranges built on the GE platform Verified model numbers include: JB645RK6SS, JS760EP6ES, JS760DP6WW, JS760SP7SS, JS760DP7WW, JS760SP6SS, JS760FP7DS, JS760FP6DS, JS760EP7ES, JB860EJAES, JB860FJADS, and GRS500PV1SS. Note: This is a six-terminal switch built specifically for a dual (bridge) element with a figure-8 style shaft and two female mounting holes — it is NOT interchangeable with a standard single-element infinite switch such as the WB24T10029 or WB24T10025, which use fewer terminals and a different shaft profile. Fitting a standard single-element switch to a dual-element burner circuit will not correctly control both coil zones. Always verify your full model number and confirm the affected burner is a dual/bridge element before ordering. Contact our support team with your model number if you're unsure. Key Features Genuine GE OEM part — factory-specified contact design for dual-element switching Six-terminal design controls both the inner coil and outer ring of a dual (bridge) surface element Figure-8 style shaft with two female mounting holes matched to the original control panel bracket Infinite switch design allows continuous heat adjustment rather than a handful of fixed positions Rated 240VAC at 15 amps Resolves "burner won't turn on," "outer ring not working," "won't turn off," and "stuck at one heat level" symptoms caused by worn or corroded switch contacts Direct drop-in replacement — mounts to the same control panel bracket and wiring harness Replaces 191D4774P005, AP5999509, PS11729102, EAP11729102, and 4464832 Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number WB24X25013 Part Type Range Surface Burner Infinite Switch (Dual/Bridge Element) Condition Genuine OEM Brand GE Element Type Controlled Dual (bridge) surface element — inner coil + outer ring Terminal Connections 6 Shaft Style Figure-8 Mounting Two female mounting holes Voltage 240VAC Amperage 15A Function Cycles element power to allow continuous (infinite) heat adjustment across both coil zones Quantity 1 switch Compatible Brands GE, Hotpoint, select Kenmore Installation Notes ⚠️ 240V Circuit — Unplug Range Or Shut Off Breaker Before Starting Disconnect power at the outlet or shut off the circuit breaker before beginning — this switch operates on a 240V circuit, and working on it while powered presents a serious shock hazard. Wear work gloves. Remove the burner knob (it typically pulls straight off, though some models use a small retaining clip) then remove the screws securing the control panel or backsplash to reach the switch from behind. Photograph the wiring before disconnecting anything — this is a six-terminal switch, and getting even one wire out of place can miswire the inner coil, the outer ring, or both. Label each wire as you remove it. Disconnect all six terminal connections from the old switch, then remove the mounting screws from the two mounting holes and pull the switch free from its figure-8 shaft opening. Install the new WB24X25013 in the same orientation, reconnect each of the six wires exactly as labeled, and secure the mounting hardware. Reinstall the control panel or backsplash, press the knob back onto the shaft, restore power, and test the burner at every knob position — confirm the inner coil and outer ring both activate correctly (together and, if your model supports it, with the outer ring switched off independently) before considering the repair complete. Tools needed: Phillips screwdriver, nut driver, wire terminal pliers (helpful but optional), work gloves. Frequently Asked Questions How do I know if my burner uses a dual-element switch like this one? Look at the burner element itself: a dual (bridge) element has two distinct coil rings — a smaller inner coil and a larger outer ring — usually with a separate control or a knob position that lets you activate just the inner coil for a small pan or both rings together for a large pot. A standard single-ring element has only one coil and uses a simpler switch with fewer terminals. If your range has this two-ring burner design, the WB24X25013 (or the exact switch behind it) is the correct type — but always confirm your model number, since dual-element switches vary by range generation. Only the outer ring of my dual burner doesn't work. Is it the switch or the element? It could be either, and it's worth narrowing down before ordering. If the inner coil heats normally but the outer ring never activates at any knob position, check the outer ring element itself first — a broken element coil is a common and cheaper fix than a switch. If the outer ring element tests fine but the switch's six-terminal wiring specific to the outer coil circuit has failed or corroded, the infinite switch is the correct replacement. Can I use a standard single-element infinite switch instead if this one is out of stock? No. A standard single-element switch has fewer terminals and cannot correctly control the two separate coil zones of a dual (bridge) burner. Wiring a single-element switch into a dual-element circuit will leave one coil zone permanently uncontrolled or non-functional. Always order the six-terminal dual-element switch specified for your model. What does "infinite switch" mean? An infinite switch lets you dial in a continuous range of heat rather than a few fixed positions, by rapidly cycling the element's power on and off at a ratio set by the knob — low settings get short power pulses, high settings get long ones. When the internal contacts wear or weld together from years of cycling, the switch can get stuck feeding constant power (burner always hot) or stop switching at all (burner always off), regardless of where the knob is turned. A spill got into the control panel and now the burner won't turn off. Is that the switch? Very likely, yes. Liquid boilovers and spills are one of the most common causes of infinite switch failure — moisture gets into the switch body, corrodes or bridges the internal contacts, and the switch can end up stuck feeding power continuously even with the knob turned to off. If you suspect this, shut off power to the range immediately at the breaker rather than relying on the knob, since a shorted switch may not respond to it at all. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by GE to factory specifications — guaranteed fit, materials, and performance. It matches the original six-terminal wiring, figure-8 shaft, 240VAC/15A electrical rating, and dual-coil switching behavior of the infinite switch originally installed for the dual (bridge) element in your GE, Hotpoint, or Kenmore range. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less