Search results for "refrigerator switch"

XPARTCO 3392519 Dryer Thermal Fuse Replaces WP3392519 The XPARTCO 3392519 is an aftermarket replacement dryer thermal fuse compatible with select gas and electric dryers from Whirlpool, Kenmore, KitchenAid, Maytag, Roper, Estate, Inglis, Crosley, Amana, Admiral, and Magic Chef. The thermal fuse is a critical one-time-use safety device mounted on the exhaust duct or blower wheel housing that monitors the dryer's operating temperature. When the dryer overheats — typically due to a clogged exhaust vent or restricted airflow — the thermal fuse permanently opens the circuit and cuts power to the heating system to prevent a fire. Once blown, the thermal fuse cannot be reset and must be replaced. This part measures 2 inches long x 1/2 inch wide, features two 3/16-inch terminals, and opens at approximately 196°F (91°C). Important: always check and clear the exhaust vent when replacing this fuse, as restricted airflow is the most common cause of thermal fuse failure. Quick Answer The XPARTCO 3392519 Dryer Thermal Fuse fixes dryers that won't start, won't heat, or stop mid-cycle due to overheating. It is a one-time-use safety fuse that permanently opens at 196°F (91°C) to cut power and prevent fires. Compatible with select Whirlpool, Kenmore, KitchenAid, Maytag, Roper, Estate, Inglis, Crosley, Amana, Admiral, and Magic Chef dryers. Replaces WP3392519 and many other part numbers. Common Problems This Part Fixes Dryer won't start at all Dryer runs but produces no heat Dryer stops mid-cycle and won't restart Timer advances but drum does not heat Dryer shuts off too soon before clothes are dry No continuity detected across fuse terminals during testing Replaces Part Numbers This thermal fuse directly replaces the following OEM and cross-reference part numbers: 3392519, WP3392519, 3388651, WE4X857, G4AP0500, 6L4101, 6L4101091C, ET401, 3388651, 694511, 80005, AWP47582, PD00002311, EAP11741460, AP6008325, PS11741460 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This thermal fuse is compatible with select gas and electric dryers from the following brands: Whirlpool dryers (including Duet and Cabrio series) Kenmore / Sears dryers (including Elite series) KitchenAid dryers Maytag dryers (including Centennial and Neptune series) Roper dryers Estate dryers Inglis dryers Crosley dryers Amana dryers Admiral dryers Magic Chef dryers Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features One-time-use safety device — permanently opens at 196°F (91°C) to cut power and prevent dryer fires Mounts on the exhaust duct or blower wheel housing — easy access for DIY replacement Aftermarket replacement built to OEM-equivalent quality standards 2-terminal design — direct drop-in replacement, no modification required Broad compatibility across 11 major appliance brands DIY-friendly repair — installs with basic hand tools in under 30 minutes Budget-friendly safety fix — one of the most common and least expensive dryer repairs Product Specifications Part Number 3392519 Part Type Dryer Thermal Fuse Condition Aftermarket Replacement Application Gas and Electric Dryers Opening Temperature 196°F (91°C) Length 2 inches Width 1/2 inch Terminal Size 3/16 inch (2 terminals) Resettable No — one-time use only, must be replaced when blown Location on Dryer Exhaust duct / blower wheel housing Compatible Brands Whirlpool, Kenmore, KitchenAid, Maytag, Roper, Estate, Inglis, Crosley, Amana, Admiral, Magic Chef Installation Notes ⚠️ Safety First — Unplug Dryer and Shut Off Gas Before Starting Unplug the dryer from the power source (and shut off the gas supply for gas dryers) before beginning any repair. The thermal fuse is located on the exhaust duct or blower wheel housing — access it by removing the back or front panel depending on your dryer model. Disconnect the two wire terminals from the old fuse, remove the fuse from its bracket, install the new fuse in the same position, reconnect the terminals, and reassemble the panel. Tools needed: Phillips screwdriver, 1/4-inch nut driver, and a multimeter to confirm the new fuse has continuity. ⚠️ Important: Before completing the repair, always check and clear the exhaust vent of any lint buildup — a blocked vent is the most common cause of thermal fuse failure and will blow the new fuse if not corrected. Frequently Asked Questions Will the 3392519 fit my dryer? This thermal fuse is compatible with select gas and electric dryers from Whirlpool, Kenmore, KitchenAid, Maytag, Roper, Estate, Inglis, Crosley, Amana, Admiral, and Magic Chef. Use the model search above to verify your model, or contact our support team before ordering. What does a dryer thermal fuse do? The thermal fuse is a one-time-use safety device that monitors the temperature inside the dryer. When the dryer overheats — typically due to a clogged exhaust vent — the fuse permanently opens the circuit, cutting power to the heating system to prevent a fire. Once blown, it cannot be reset and must be replaced. How do I know if my thermal fuse is blown? Test the fuse with a multimeter set to continuity mode. Touch the probes to each of the two terminals. A working fuse will show continuity (beep or near-zero ohms). A blown fuse will show no continuity (open circuit). If there is no continuity, the fuse is blown and must be replaced. Why did my thermal fuse blow? The most common cause is restricted airflow due to a clogged or kinked exhaust vent, a plugged lint trap, or a damaged blower wheel. Always check and clear the exhaust vent before or after replacing the fuse — failing to do so will cause the new fuse to blow again. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is designed to deliver reliable overheat protection at a more affordable price point. Shop With Confidence Parts-O-Matic is a U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock parts for major appliance brands and ship quickly from our U.S. warehouse. Our team is available to help you verify compatibility before you buy. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

DE47-20034A Microwave Genuine High Limit Thermostat Thermal cutout. High limit thermostat. Open for continuity at room temperature, closes when it gets hot. Fits Samsung over counter microwaves. Replaces Part Numbers:DE47-20034A, AP4219754, PS4226431.  California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

XPARTCO Dryer Repair Set XPARTCO EXP526 Dryer Belt and Idler Pulley Set 2-piece drum drive repair set replacing 661570V and W10837240 on compatible Whirlpool-built dryers. Product Overview The XPARTCO EXP526 Dryer Belt and Idler Pulley Set combines two common dryer drive-system wear parts in one repair package: a drum drive belt and a complete idler pulley assembly with arm/bracket. The belt transfers motor power to the dryer drum, while the idler assembly maintains the proper belt tension needed for smooth drum rotation. Quick Answer EXP526 includes 2 pieces: one 661570V-style drum belt and one W10837240-style idler pulley assembly. The belt is approximately 93-1/2 inches long, 1/4 inch wide, with 4 ribs and 3 grooves. Common Problems This Kit May Fix Dryer drum will not turn Broken or stretched drum belt Squealing or chirping from the idler area Intermittent drum rotation Belt slipping or running loose Worn or seized idler pulley Replaces and Cross-References WP40111201, 40111201, 14218936, 40051501, 40051502, 59174, PD00002505, EAP11742271, AP6009126, PS11742271, R0606549, WP40111201VP, 661570V, 661570, 3387610, 3389728, 3393999, 339728, 661570VP, PD00023608, AP5983729, PS11722115, W10837240, W10547287, W10547290, 3387372, 3388674, W10118754, W10118756, W10837240VP, PD00025564, FIX11726337, AP5988716, PS11726337, 279640, AP3094197, 279640VP, 2958, 3388672, 697692, TJ279640, W10468057, AH334244, EA334244, ER279640, PS334244 Cross-reference numbers are provided for identification. XPARTCO is an aftermarket replacement brand and is not manufactured by Whirlpool Corporation. Compatibility Fits select Whirlpool-built dryers using both the 661570V belt and W10837240 idler assembly. Verified examples include: WED8300SW0 MEDB750YW0 NED7300WW1 110.C87571601 110.C87566601 110.C96562500 Important: This is only a partial model list. Some similar dryers use a different belt or idler design. Verify the complete dryer model number and original part numbers before ordering. Key Features Complete 2-piece drive repair set Includes drum belt and idler pulley assembly Idler includes pulley wheel, arm/bracket and axle Helps restore proper drum rotation and belt tension Quality XPARTCO aftermarket replacement Product Specifications Kit Number EXP526 Brand XPARTCO Kit Contents 1 Drum Belt + 1 Idler Pulley Assembly Belt Reference 661570V Belt Length Approx. 93-1/2 in. Belt Width Approx. 1/4 in. Belt Rib/Groove 4 Ribs / 3 Grooves Idler Reference W10837240 Idler Type Complete Pulley with Arm/Bracket Condition New Aftermarket Replacement Installation Notes Disconnect the dryer from electrical power before service. Shut off the gas supply on gas dryers. Access the drum drive system according to the appliance service procedure. Note the original belt routing around the motor pulley and idler before removal. Install the idler assembly securely and confirm the pulley rotates freely. Install the new belt with the ribbed side against the drum and motor pulley. Route the belt through the idler correctly so proper tension is applied. Rotate the drum by hand before reassembly to confirm smooth belt tracking. Diagnostic tip: If a belt failed prematurely, inspect the drum rollers, motor pulley, drum alignment, and idler system before returning the dryer to service. FAQ What is included in EXP526? One 661570V-style drum drive belt and one W10837240-style complete idler pulley assembly. How many ribs does the belt have? The 661570V-style belt has 4 ribs and 3 grooves and is approximately 93-1/2 inches long. Is this a Genuine Whirlpool OEM kit? No. EXP526 is a quality XPARTCO aftermarket replacement set designed to replace the listed OEM part numbers. Will it fit every Whirlpool dryer? No. Whirlpool-built dryers use multiple belt and idler designs. Verify your complete model number and the original belt/idler part numbers before ordering. Shop With Confidence Confirm your dryer model number before ordering. Compatibility support is available to help verify the correct belt and idler combination. XPARTCO Replacement2-Piece Drive KitCompatibility SupportFast U.S. Shipping

Read more less

Genuine OEM WB26X44167 Wall Oven Convection Motor Kit The Genuine OEM GE WB26X44167 is the convection motor kit for select GE wall ovens. The motor spins the convection fan blade that circulates hot air through the oven cavity for even heating. When it wears out, airflow weakens, the oven gets noisy, and convection performance drops. This is the original GE part, not an aftermarket equivalent. It is sold as a kit. Check your model number before ordering. Quick Answer The Genuine OEM WB26X44167 Convection Motor Kit replaces the convection fan motor on a compatible GE wall oven when it has failed. Replaces WB26T10069, WB26X21763, WB26X23476, WB26X27929 and WB26X31224. Classic symptoms: no convection heat, uneven baking, weak airflow, or a noisy oven fan. Common Problems This Part Fixes No convection heat, or the convection fan not working Uneven baking Weak airflow or declining convection performance Increased noise from the oven fan Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This convection motor kit replaces or supersedes the following part numbers: WB26X44167, WB26X23476, WB26X27929, WB26X31224, WB26T10069, WB26X21763, AGE22636, AP7193683, OEM21581058, EAP16742591, PD00089141, PS16742591 If your old motor shows a different number, contact our support team and we'll check whether it matches. Compatibility This convection motor kit is listed for GE, GE Profile and Café wall ovens, including these examples: GE CT9050EK2DS, CT9050SH1SS, CT9070SH1SS GE CT9550EK2DS, CT9550SH1SS, CT9570SL1SS GE CTD70DM2N2S5, CTD70DP2N1S1 GE PT7550DF2BB, PT7550EH1ES, PCT7050DF2BB Note: The models above are a sample, not a full list. GE sells several convection motor kits with different part numbers. Check your full model number against your parts diagram, or contact our support team to verify fit before ordering. Key Features Genuine OEM GE part, not an aftermarket equivalent Drives the convection fan that circulates hot air for even heating Replaces five earlier GE convection motor part numbers Sold as a kit Product Specifications Part Number WB26X44167 OEM Part Number WB26X44167 Part Type Wall Oven Convection Motor Kit Condition Genuine OEM Manufacturer GE Quantity 1 Kit Application Select GE Wall Ovens Installation Notes ⚠️ Disconnect Power Before Installing Shut off the oven's circuit breaker or unplug the oven before you begin, let the oven cool, and wear work gloves. Remove the oven's rear cover per your model's service guide to reach the motor, disconnect the wire connector, and remove the old motor. Install the new motor, reconnect the wiring, refit the cover, restore power, and run a convection cycle to confirm the fan runs quietly. Frequently Asked Questions My oven fan is noisy or not turning. Is this the part I need? It can be. With the oven off and cool, turn the fan blade by hand. If it is hard to turn, the motor bearings may be worn. A multimeter continuity check on the motor can confirm a failed motor. Is this an OEM or aftermarket part? This is a genuine OEM part from GE, not an aftermarket equivalent. What is in the kit? It is sold as a convection motor kit. Retailers do not itemize the contents, so contact our support team if you need to confirm them before ordering. Will this fit my wall oven? It is listed for many GE wall oven models, but the model list above is only a sample. Check your full model number against your parts diagram, or contact our support team and we'll verify it before you order. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Genuine OEM Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO DC47-00018A Dryer Hi Limit Thermostat The XPARTCO DC47-00018A is an aftermarket replacement cycling high-limit thermostat for Samsung and select Kenmore electric dryers. This is a genuine, automatically resetting thermostat — not a one-time fuse. It monitors temperature in the heating circuit and opens to cut power to the heating element at approximately 260°F, protecting the dryer from overheating. Once the temperature drops to around 210°F, it closes again on its own, letting the dryer resume heating without any part replacement needed. This thermostat works alongside a downstream thermal fuse (such as our DC96-00887C listing) in the same overheat-protection circuit. If this thermostat is cycling excessively, tripping prematurely, or failing to regulate temperature correctly, it can put stress on that thermal fuse, sometimes causing it to blow as a last-resort safety measure. Symptoms of a failing high-limit thermostat include no heat or insufficient heat, drying that takes too long, or the dryer shutting off too soon before a load is fully dry. It directly replaces 35001092, WP35001092, 1122485, AP4201898, PS4205217, EAP2430930, PS2430930, and AP6008682. Quick Answer The XPARTCO DC47-00018A Dryer Hi Limit Thermostat fixes Samsung and select Kenmore electric dryers with no heat or insufficient heat, drying that takes too long, or premature shutoff before a load is fully dry. Opens at approximately 260°F, resets automatically around 210°F. Replaces 35001092, WP35001092, 1122485, AP4201898, PS4205217, EAP2430930, PS2430930, AP6008682. This is a resettable thermostat, not a fuse — it does not need replacement after each trip. It's a different component from our DC96-00887C thermal fuse listing, though the two are often checked together. Common Problems This Part Fixes Dryer has no heat or insufficient heat Drying takes too long to complete a cycle Dryer shuts off too soon, before clothes are fully dry Timer will not advance through the cycle Dryer that stopped working suddenly after running unusually hot Dryer with a history of repeated downstream thermal fuse failures Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dryer high-limit thermostat directly replaces the following OEM and cross-reference part numbers: DC47-00018A, AP4201898, T-O-D 60T11, ASM33627, 1122485, PD00002011, PS4205217. WP35001092, 35001092, PD00004704, EAP11741822, AP6008682, AWP47350, PS11741822, L260-50F If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This high-limit thermostat is compatible with select Samsung electric dryers, and also fits select Kenmore dryers built on the Samsung platform, including model numbers such as: DV5471AEW/XAA DV40J3000EW/A2, DV42H5000EW/A3, DV45H7000EW/A2, DV48H7400EW/A2 DV400EWHDWR/AA DVE50M7450W/A3 Note — resettable thermostat, not a fuse: This DC47-00018A is a true cycling thermostat that resets itself automatically. Our DC96-00887C listing, despite frequently being labeled a "thermostat" on other marketplaces, is actually a one-time thermal fuse mounted separately on the blower housing — it cannot reset and must be replaced once blown. The two are different device types serving the same circuit. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Aftermarket replacement cycling high-limit thermostat — automatically resetting, no replacement needed after each trip Opens at approximately 260°F, resets around 210°F Resolves "no heat," "insufficient heat," "takes too long to dry," and "shuts off too soon" symptoms Genuine thermostat, distinct from the downstream thermal fuse in the same circuit No special tools required for installation Replaces 35001092, WP35001092, 1122485, AP4201898, PS4205217, EAP2430930, PS2430930, and AP6008682 Compatible with Samsung and select Kenmore electric dryers Aftermarket replacement built to OEM-equivalent quality standards Product Specifications Part Number XPDC47-00018A OEM Part Number DC47-00018A Part Type Dryer Cycling High-Limit Thermostat Condition Aftermarket Replacement Type Automatically resetting — not a one-time fuse Open Temperature ~260°F Reset Temperature ~210°F Related Component DC96-00887C thermal fuse (blower housing, different device, sold separately) Quantity 1 high-limit thermostat Compatible Brands Samsung, select Kenmore Installation Notes ⚠️ Unplug Dryer Before Starting Disconnect power at the outlet or shut off the circuit breaker before beginning. Wear work gloves. Access is typically through the rear panel, near the heater duct and blower housing area where this thermostat is mounted. Photograph the wiring connections before disconnecting anything, since this thermostat can be positioned close to other similar-looking components in the same circuit. Remove the old thermostat from its mounting position, noting orientation, and disconnect its wiring. Install the new DC47-00018A in the same position, reconnecting wiring exactly as photographed. Reassemble the panel, restore power, and run a full test cycle to confirm normal, consistent heating with no premature shutoffs. Tools needed: Phillips or nut driver (model-dependent), work gloves. Frequently Asked Questions Do I need to reset this thermostat after it trips, or replace it? Neither, in normal operation — this is a genuine cycling thermostat that resets itself automatically once the dryer cools to around 210°F. You should only need to replace it if it has failed outright (stuck open, stuck closed, or no longer switching at the correct temperatures), not simply because it tripped once during normal operation. My dryer shuts off before the load is fully dry. Is that this part? It's a strong possibility. If this high-limit thermostat is tripping prematurely — opening at a lower temperature than it should — the dryer can cut heat and end the cycle early even though the load isn't actually dry yet. This is one of the more common symptoms this thermostat addresses. My thermal fuse keeps blowing. Could this thermostat be the underlying cause? Yes, this is worth investigating. This thermostat and the downstream thermal fuse (our DC96-00887C listing) protect the same circuit at different points. If this thermostat isn't regulating temperature correctly — cycling excessively or failing to catch a temperature spike — the thermal fuse can end up blowing repeatedly as the last line of defense. If you've replaced the fuse more than once, checking or replacing this thermostat at the same time is a reasonable next step. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Samsung OEM part, but is manufactured to match the electrical specifications and opening/reset temperatures of the original DC47-00018A high-limit thermostat used in compatible Samsung and Kenmore electric dryers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

137292700 Dryer Genuine OEM Drum Belt The 137292700 is a genuine Frigidaire OEM multi-rib drum belt for Frigidaire stacked laundry center (combination washer/dryer) units, and also fits select Crosley, Electrolux, Gibson, Kelvinator, Kenmore, Tappan, and White Westinghouse combo models. This belt attaches to the motor pulley and spins the drum as the motor rotates, keeping clothes tumbling evenly throughout the drying cycle. Measures approximately 89-1/2" long and 1/4" wide, with multiple ribs. Over time, this belt naturally dries out, cracks, or breaks from regular use. If your dryer is running but the drum won't turn, there's a good chance the belt has broken. Symptoms of a failing belt include the drum not turning, loud banging noises, or the dryer failing to tumble clothes. It directly replaces 134163500, 134503900, 5303283287, 4PH 2273, 4PH2273, AFR14366, AH3408299, AP4565702, EA3408299, EAP3408299, PD00000115, PS3408299. Quick Answer The 137292700 Dryer Genuine OEM Drum Belt fixes Frigidaire, Crosley, Electrolux, Gibson, Kelvinator, Kenmore, Tappan, and White Westinghouse stacked laundry center units where the drum won't turn, you hear loud banging noises, or the dryer won't tumble clothes. Approximately 89-1/2" long, 1/4" wide, multiple ribs. Replaces 134163500, 134503900, 5303283287, 4PH 2273, 4PH2273, AFR14366, AH3408299, AP4565702, EA3408299, EAP3408299, PD00000115, PS3408299. This is a laundry center (stacked combo) belt, distinct from standalone dryer belts — verify your full model number before ordering. Common Problems This Part Fixes Drum won't turn even though the motor is running Loud banging noises during operation Dryer failing to tumble clothes Belt visibly cracked, dried out, or broken Drum stopping mid-cycle Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dryer drum belt directly replaces the following OEM and cross-reference part numbers: 134163500, 134503900, 5303283287, 4PH 2273, 4PH2273, AFR14366, AH3408299, AP4565702, EA3408299, EAP3408299, PD00000115, PS3408299 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This drum belt is compatible with select Frigidaire stacked laundry center units, and also fits select Crosley, Electrolux, Gibson, Kelvinator, Kenmore, Tappan, and White Westinghouse combo units built on the same platform, including model numbers such as WLXG42REW0, FLSE72GCTC, FLSG72GCT1, FLSG72GCT6, LCE852LL1, FLXG52RBS2, FLXG52RBS8, FLXE52RBS9, CLCG900FW0, CLCG900FW1, CLCG900FW2, CLCG900FW3, CLCE900FW0, CLCE900FW1, CLCE900FW2, CLCG500FW0, CLCG500FW1, CLCE600RW0, CLCE500MW1, CLCE500FW2, and CLCE500FW4. Note: This is a laundry center (stacked washer/dryer combo) belt, distinct from standalone Frigidaire dryer belts. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Genuine Frigidaire OEM part — factory-specified multi-rib design Attaches to the motor pulley to spin the drum for laundry center (combo) units Resolves "drum won't turn," "loud banging noises," and "won't tumble" symptoms Approximately 89-1/2" long, 1/4" wide, multiple ribs Direct drop-in replacement matching the original length and profile Replaces 134163500, 134503900, 5303283287, 4PH 2273, 4PH2273, AFR14366, AH3408299, AP4565702, EA3408299, EAP3408299, PD00000115, PS3408299 Compatible with Frigidaire, Crosley, Electrolux, Gibson, Kelvinator, Kenmore, Tappan, and White Westinghouse laundry center units Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number 137292700 Part Type Laundry Center Multi-Rib Drum Belt Condition Genuine OEM Brand Frigidaire Application Stacked Washer/Dryer Laundry Centers Length Approx. 89-1/2" Width 1/4" Ribs Multiple Function Transmits motor rotation to spin the drum Repair Difficulty Moderate — laundry center disassembly required Quantity 1 drum belt Compatible Brands Frigidaire, Crosley, Electrolux, Gibson, Kelvinator, Kenmore, Tappan, White Westinghouse Installation Notes ⚠️ Unplug The Laundry Center Before Starting Disconnect power to the laundry center unit at the outlet before beginning. Wear work gloves. This repair is best approached from the top down: remove the top of the unit first, which gives more room to get the dryer tub out. Remove the two screws from the vented plate on the back of the machine to access and undo the old belt. Since this is a stackable washer/dryer combo, also remove the white plate on the front between the washer and dryer sections for full access. Locate the old belt connecting the motor pulley to the drum and remove it. Fit the new 137292700 belt around the drum and motor pulley in the same path as the old one, making sure it seats correctly and is properly tensioned. Reassemble the front plate, vented back plate, and top of the unit. Restore power and run a test cycle to confirm the drum tumbles smoothly with no banging or unusual noise. Tools needed: putty knife, screwdriver set, work gloves. Frequently Asked Questions The motor is running but the drum won't turn. Is this the belt I need? Yes, this is the classic and most reliable sign of a broken drum belt. If you can hear the motor running normally but the drum itself stays still, the belt has likely dried out and broken, no longer connecting the motor's rotation to the drum. Is this the same as a standalone Frigidaire dryer belt? No, this belt is specifically sized and profiled for Frigidaire-style stacked laundry center units, where the washer and dryer are combined into one appliance. It's a different part from standalone Frigidaire dryer belts used on separate dryers. Confirm your unit type and model number before ordering. Is this a difficult repair? It's a moderate repair since it involves removing the top of the laundry center unit, the vented back plate, and the front plate between the washer and dryer sections to get full access to the belt. One customer described working from the top down as the easiest approach, since it gives more room to remove the dryer tub. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by Frigidaire to factory specifications — guaranteed fit, materials, and performance. It matches the original length, width, and rib pattern of the multi-rib drum belt originally installed in your laundry center. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

154825001 Genuine OEM Frigidaire Dishwasher Heating Element The 154825001 is a genuine Frigidaire OEM round heating element that sits exposed at the bottom of the dishwasher tub. Unlike a hidden element concealed beneath the tub floor, this is a visible ring-shaped element you can see sitting right in the bottom of the wash chamber. It serves two jobs: it heats the wash water to the temperature needed to properly dissolve detergent and break down grease and food soil, and at the end of the cycle it provides the heat that drives the drying phase, helping moisture evaporate off your dishes rather than leaving them wet. Mounted through a 0.98" hole with two mounting nuts and connected by two wire terminals, this element carries a pair of white alignment dots that must line up with the tub's retaining clips during installation. Over time, mineral buildup from hard water, general corrosion, or simple electrical wear can cause the element to fail. A failing or dead element produces a specific and recognizable pattern: water never gets hot enough to clean effectively, dishes come out wet at the end of the cycle instead of dry, and the whole cycle may run noticeably longer as the dishwasher's control tries to compensate. It directly replaces AP5628696, 154482901, 154663801, 2308825, PS3653449, and EAP3653449. As a genuine OEM part, the 154825001 is manufactured by Frigidaire to factory specifications — guaranteed fit, materials, and performance. Quick Answer The 154825001 Genuine OEM Frigidaire Dishwasher Heating Element fixes Frigidaire, Kenmore, Electrolux, Crosley, Gibson, Kelvinator, Tappan, and Westinghouse dishwashers with dishes that don't get properly clean, dishes that come out wet instead of dry, or cycles that take longer than they used to. Exposed round heating element, 0.98" mounting hole, 2 wire terminals. Replaces AP5628696, 154482901, 154663801, 2308825, PS3653449, EAP3653449. Before replacing, test the old element with a multimeter for resistance — a bad control board relay can produce identical symptoms with a perfectly good element. Common Problems This Part Fixes Dishes not getting properly clean because wash water isn't reaching the correct temperature Dishwasher not drying dishes — items come out wet at the end of the cycle Cycle taking noticeably longer than usual to complete Visible damage, corrosion, or discoloration on the element itself Element that doesn't glow or heat up when the wash cycle is running Water leaking near the high-temperature wire connector at the element terminals Mineral scale buildup visible on or around the element Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dishwasher heating element directly replaces the following OEM and cross-reference part numbers: 154825001, 154482901, 154663801, 2308825, AP5628696, AFR14520, EAP3653449, PD00000951, PS3653449. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This heating element is compatible with select Frigidaire, Electrolux, Kenmore, Crosley, Gibson, Kelvinator, Tappan, and Westinghouse dishwashers, spanning a wide range of model series including BBBD, BGBD, BGHD, DGBD, DGCD, DGHD, FDB, FDBB, FDBD, FFBD, FFID, FGBD, FGCD, FGHD, FGID, FPHD, FPID, GLD, GSB, LEDB, LFBD, LFID, LGBD, LGHD, and PLD. Verified model numbers include: FFCD2413UW1A, FGID2466QF4A, FGID2466QF5A, FFID2426TD1A, FGBD2438PF4A, FGHD2465NF1A, FGHD2433KF1, LFID2426TF1A, LFID2422RF0A, LFID2422RF3B, LFID2422RF4B, LFID2426TF4A, LFID2426TF5A, LGBD2431LF0A, LGBD2431NF0B, LGBD2431NF1B, LGBD2432LW0A, LGBD2432LW0B, and CDB350/CDB500/CDB900 series models. Also fits Kenmore 587-series, Crosley CBD-series, Kelvinator KADB240, and White-Westinghouse WWBD2400 dishwashers. Note: This is an exposed round heating element sitting visibly in the bottom of the tub, not a hidden element mounted underneath. It is not interchangeable with hidden/concealed heating elements used on other dishwasher platforms. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Genuine Frigidaire OEM part — factory-specified heating output and terminal configuration Exposed round design sits in the tub bottom for direct water heating and drying support Resolves "not cleaning properly," "not drying," and "cycle taking too long" symptoms caused by element failure 0.98" mounting hole with two mounting nuts and wire terminals Two white alignment dots for correct positioning in the tub's retaining clips Direct drop-in replacement — no modification required Replaces 154482901, 154663801, 2308825, AP5628696, PS3653449, and EAP3653449 Compatible with Frigidaire, Electrolux, Kenmore, Crosley, Gibson, Kelvinator, Tappan, and Westinghouse dishwashers Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number 154825001 Part Type Dishwasher Round Heating Element (Exposed) Condition Genuine OEM Brand Frigidaire / Electrolux Location Bottom of the wash tub (exposed, visible) Mounting Hole 0.98 in. Terminals 2 wire connections + 2 mounting nuts Alignment 2 white dots must align with tub retaining clips Repair Difficulty Medium — basic dishwasher familiarity required Tools Required Screwdrivers, wrench set Quantity 1 heating element Compatible Brands Frigidaire, Electrolux, Kenmore, Crosley, Gibson, Kelvinator, Tappan, Westinghouse Installation Notes ⚠️ Unplug Dishwasher And Shut Off Water Before Starting — Handle The Element Carefully Disconnect power at the circuit breaker and shut off the water supply before beginning. Wear work gloves. On many models you'll need to pull the dishwasher out from under the counter to access the undercarriage — remove the two screws securing the unit to the counter first. Remove the lower rack and the lower spray arm (it typically pushes down and twists to unlock) to access the element inside the tub. From underneath, disconnect the two wires from the element's terminals and remove the two mounting nuts with a 1/2" wrench, taking care not to overtighten when you reach the new element — over-torquing can crush the sealing washers and cause a leak at the connector. Lift the old element free from its retaining clips inside the tub. To install the new 154825001, locate the two white alignment dots on the element and position them so they slide into the tub's retaining clips correctly — this ensures the element seats in its proper orientation. Push the terminals down through the mounting hole, then from underneath, reinstall and tighten the mounting nuts snugly but not excessively. Reconnect the two wires to the terminals, reinstall the lower spray arm and press it down to lock it in place, and reinstall the lower rack. Restore water and power, then slide the dishwasher back into place and secure it to the counter with its mounting screws. Run a test cycle and check underneath for any leaks at the element connection before considering the repair complete. Tools needed: screwdriver, 1/2" wrench, work gloves. Frequently Asked Questions How do I know it's the heating element and not something else, like the control board? Before replacing the element, it's worth testing it with a multimeter for resistance — a healthy element typically reads in the neighborhood of 14 ohms, though exact values vary by model. If the old element tests fine but dishes still aren't drying or getting hot enough, the more likely cause is upstream of the element itself, such as a control board relay that isn't sending power to it correctly. Some owners have replaced a perfectly good element only to find the actual fault was a bad solder connection on the control board relay — testing first can save you an unnecessary purchase. Can I clean the element instead of replacing it? Light surface cleaning to remove mineral scale buildup is reasonable and can sometimes help if reduced heating output is due to scale insulating the element. However, if the element tests as an open circuit (no continuity) or shows visible damage, cracking, or corrosion through the metal sheath, cleaning won't restore it — replacement is the correct fix at that point. I noticed water leaking near the element's wire connector. Is that related? Yes, this is a documented failure point on this element design — the high-temperature wire connector at the terminals can develop a leak, especially if the mounting nuts were overtightened during a prior installation and damaged the sealing washer. When installing the new element, tighten the mounting nuts snugly but avoid excessive force, which helps prevent this same leak point from recurring. Do I really need to pull the dishwasher out from under the counter? On most installations, yes — accessing the mounting nuts and wire terminals underneath the tub requires pulling the unit forward after removing the two screws that secure it to the counter. Some technicians have managed the nut removal with a deep socket without fully pulling the unit, but planning for full access makes the job considerably easier, especially the first time. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by Frigidaire to factory specifications — guaranteed fit, materials, and performance. It matches the original heating output, mounting configuration, and terminal layout of the element originally installed in your dishwasher. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

EXP651 Dryer Belt and Idler Pulley Kit Replaces WPW10112954, W10837240 The EXP651 is an aftermarket dryer repair kit containing two essential drum drive components for select Whirlpool, Maytag, Amana, Kenmore, KitchenAid, Crosley, Admiral, Inglis, and Roper dryers. The kit includes one drum belt (replaces WPW10112954) and one idler pulley assembly with bracket (replaces W10837240) — the two parts most commonly worn together when a dryer drum stops spinning or becomes noisy. Replacing both the belt and idler pulley at the same time is the smart repair choice. Since the dryer must be disassembled to access either part, doing both in one repair saves you from having to take the machine apart again if the second part fails shortly after. This kit covers the two most common failure points in the Whirlpool-family dryer drum drive system. Quick Answer The EXP651 Dryer Belt and Idler Pulley Kit fixes dryers where the drum is not spinning, making loud squeaking or grinding noises, or the belt has broken. Includes one 93-1/4" x 5/16" 5-rib drum belt (WPW10112954) and one idler pulley assembly with bracket (W10837240). Compatible with select Whirlpool, Maytag, Amana, Kenmore, KitchenAid, Crosley, Admiral, Inglis, and Roper dryers. What's in the Kit Part 1 of 2 Dryer Drum Belt — Replaces WPW10112954 93-1/4" L x 5/16" W x 1/8" H · 5-rib Multi-V rubber belt · Wraps around drum and connects to motor and idler pulleys to drive drum rotation Part 2 of 2 Idler Pulley Assembly with Bracket — Replaces W10837240 2-1/8" pulley diameter · 6-1/4" L x 1-1/4" W x 3-7/16" H overall · Plastic/metal construction · Maintains correct belt tension to spin the drum · Fits Whirlpool dryers with lint screen inside door Common Problems This Kit Fixes Dryer drum not spinning — motor runs but drum stays still Loud squeaking, squealing, or grinding noise during operation Clothes not tumbling during the drying cycle Thumping or slapping noise when dryer is running Belt slipping off or repeatedly breaking Burning rubber smell coming from the dryer Dryer drum turning erratically or stopping while motor continues to run Replaces Part Numbers Drum Belt (WPW10112954) cross-references: WPW10112954, W10112954, 1447719, AWP48873, PD00003553, EAP11748388, AP6015116, PS11748388. Idler Pulley Assembly (W10837240) cross-references: W10837240, W10547287, W10547290, 3387372, 3388674, W10118754, W10118756, W10837240VP, AWP41730, PD00025564, FIX11726337, AP5988716, PS11726337, 279640, AP3094197, 279640VP, 2958, 3388672, 697692, TJ279640, W10468057, AH334244, EA334244, ER279640, PS334244. If your part numbers are not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This kit is compatible with select dryers from the following brands: Whirlpool dryers (gas and electric — fits models with lint screen inside door) Maytag dryers (gas and electric) Amana dryers Kenmore / Sears dryers (select Whirlpool-built models) KitchenAid dryers Crosley dryers Admiral dryers Inglis dryers Roper dryers Note: The W10837240 idler pulley fits Whirlpool-family dryers with the lint screen located inside the door. If your dryer has the lint screen on top of the cabinet, a different idler pulley part number may be required. Contact our support team to confirm before ordering. Key Features Two-part kit covers the most common drum drive failures in Whirlpool-family dryers in a single repair Belt: 93-1/4" L x 5/16" W, 5-rib Multi-V rubber — resists cracking, stretching, and heat damage Idler pulley: 2-1/8" diameter pulley with arm and bracket — maintains correct belt tension for smooth drum rotation Replacing both parts together saves a second disassembly if the other part fails soon after Aftermarket replacement built to OEM-equivalent quality standards Belt directly replaces WPW10112954 / W10112954 — no modification required Idler pulley directly replaces W10837240 / W10547287 / W10547290 — no modification required DIY-friendly repair — installs in 30–60 minutes with basic hand tools Product Specifications Kit Part Number EXP651 Condition Aftermarket Replacement Application Gas and Electric Dryers Kit Includes 1x Drum Belt (WPW10112954), 1x Idler Pulley Assembly with Bracket (W10837240) Belt Length 93-1/4 inches Belt Width 5/16 inch Belt Height 1/8 inch Belt Ribs 5 ribs, 4 grooves (Multi-V) Belt Material Rubber Pulley Diameter 2-1/8 inches Pulley Overall Dimensions 6-1/4" L x 1-1/4" W x 3-7/16" H Pulley Material Plastic / Metal Compatible Brands Whirlpool, Maytag, Amana, Kenmore, KitchenAid, Crosley, Admiral, Inglis, Roper Installation Notes ⚠️ Safety First — Unplug Dryer Before Starting Unplug the dryer from the power source (and shut off the gas supply for gas dryers) before beginning any repair. Remove the lint screen, then unscrew the Phillips screws inside the lint screen housing. Use a putty knife to release the top panel clips and lift the top panel. Remove the front panel to access the drum and drive components. Release belt tension at the old idler pulley, lift the drum slightly, and slide the old belt off. Remove the old idler arm assembly by unscrewing the mounting screw, then install the new W10837240 idler pulley assembly and secure with the screw. Loop the new WPW10112954 belt around the drum with the ribbed side facing inward, then route it around the new idler pulley and motor pulley. Consult your model's service manual or a model-specific repair video for the correct belt path. Reassemble and run a test cycle. Tools needed: Phillips screwdriver, putty knife or flat pry tool. Frequently Asked Questions Why should I replace the belt and idler pulley at the same time? The belt and idler pulley wear together — when one fails, the other is usually close behind. Since the dryer must be fully disassembled to access either part, replacing both in a single repair saves you from having to take the machine apart again soon after. It also protects the new belt from being damaged by a worn pulley, and vice versa. How does the W10837240 differ from other Whirlpool idler pulleys? The W10837240 is the updated idler pulley arm and bracket assembly designed for Whirlpool-family dryers that have the lint screen inside the door. It replaces the older W10547287 and W10547290 assemblies. Some older or different Whirlpool models use a different idler pulley style — if you're unsure which one your dryer needs, contact our support team with your model number before ordering. What is the difference between WPW10112954 and W10112954? These are the same belt. WPW10112954 is the updated Whirlpool OEM part number that superseded the original W10112954. Both refer to the identical drum belt included in this kit. Should I also replace the drum rollers at the same time? It depends on the condition of your rollers. Since the dryer is already fully disassembled, it is a good opportunity to inspect the drum support rollers for flat spots, cracks, or wobbling. If they show any wear, replacing them at the same time is recommended to avoid a third disassembly. Check your model's roller part number before ordering. Are these OEM or aftermarket parts? Both parts in this kit are aftermarket replacements built to OEM-equivalent quality standards. They are not genuine Whirlpool OEM parts, but are manufactured to match the dimensions and performance of the original WPW10112954 belt and W10837240 idler pulley assembly. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

21001335 Washer Control Timer Replaces Part Numbers: 21001335, 436688, AH2017781, EA2017781, AP4025600, PS2017781.      

Read more less

W11396717 Genuine OEM Whirlpool Washer Drain Pump Assembly The W11396717 is a Genuine OEM Whirlpool replacement drain pump assembly compatible with select Whirlpool, Maytag, and Kenmore high-efficiency top-load washers — including the Whirlpool WTW5100, WTW6120, WTW7120, WTW8120, and WTW8127 series, and the Maytag MVW6200, MVW6230, MVW7230, MVW7232, and MVW8230 series. The drain pump removes water from the washer tub during the drain portion of each wash cycle. When the pump fails, the washer will not drain, will leave standing water in the tub, stop mid-cycle, or make loud humming, grinding, or rattling noises during the drain phase. Rated 120V, 60Hz, 1.2A (CL.F duty class), this complete pump assembly is mounted to the underside of the outer tub and secured by three mounting screws. It directly replaces the earlier W11263349 as well as 4960510, AP6974116, PS12731177, and EAP12731177. Note: the pump is accessed from the bottom of the washer — the machine must be tilted or laid on its back to reach the mounting screws. Installs in 20–35 minutes with basic hand tools. Quick Answer The W11396717 Genuine OEM Whirlpool Washer Drain Pump fixes Whirlpool and Maytag HE top-load washers that won't drain, leave standing water, stop mid-cycle, or make loud noise during the drain cycle. 120V/60Hz/1.2A CL.F. Mounted on the underside of the outer tub — access by tilting the washer. Replaces W11263349, 4960510, AP6974116, PS12731177, EAP12731177. Compatible with Whirlpool WTW5100/6120/7120/8120/8127 and Maytag MVW6200/6230/7230/7232/8230 series top-load washers. Common Problems This Part Fixes Washer not draining — standing water remaining in the tub after a cycle Washer stopping mid-cycle due to a drain fault Loud humming during the drain phase — motor energized but pump not moving water Grinding or rattling during drain — damaged impeller or worn bearings Clothes excessively wet after a full cycle — pump not fully removing water before spin Water draining very slowly — pump motor weakening below rated performance Water leaking from the pump area underneath the washer Replaces Part Numbers This drain pump directly replaces the following OEM and cross-reference part numbers: W11396717, W11263349, Hanyu B25-3A04, AP6974116, AWP44690, EAP12731177, PD00065247, PS12731177 W11396717 is the current production part number superseding W11263349. If your parts diagram shows W11263349, the W11396717 is the correct current replacement. Contact our support team if you need confirmation before ordering. Compatibility This drain pump is compatible with select HE top-load washers from the following brands and series: Whirlpool top-load washers — WTW5100HC0, WTW5100HW0, WTW5105HC0, WTW5105HW0, WTW6120HC0, WTW6120HW0, WTW7120HC0, WTW7120HC1, WTW7120HW0, WTW8120HC0, WTW8120HW0, WTW8127LC1, WTW8127LW0, WTW8127LW1 and related models Maytag top-load washers — MVW6200KW0, MVW6230HC0, MVW6230HW0, MVW6230RHW0, MVW7230HC0, MVW7230HC1, MVW7230HW0, MVW7230HW1, MVW7232HC0, MVW7232HC1, MVW7232HC2, MVW7232HW0, MVW7232HW1, MVW7232HW2, MVW8230HC0, 7MMVW7230LC0, 7MMVW7230LW0 and related models Kenmore / Sears top-load washers — 11021112021, 11021652020, 11031652020 and related models Note: This pump is mounted on the underside of the outer tub and requires tilting or laying the washer on its back for access. Always verify your model number before ordering. Key Features Removes water from the tub during drain and spin cycles for proper washer operation Rated 120V, 60Hz, 1.2A (CL.F) — correct electrical specifications for compatible HE top-load washers Current production part — directly supersedes W11263349 Mounted on the underside of the outer tub and secured by three mounting screws — tilt or lay washer on its back for access Replaces W11263349, 4960510, AP6974116, PS12731177, EAP12731177, and B25-3A04 Compatible with Whirlpool WTW5100/6120/7120/8120/8127 and Maytag MVW6200/6230/7230/7232/8230 series top-load washers Genuine OEM part manufactured by Whirlpool to factory specifications — guaranteed fit and performance DIY repair — installs in 20–35 minutes with basic hand tools Product Specifications Part Number W11396717 Supersedes W11263349 Part Type HE Top-Load Washer Drain Pump Assembly Condition Genuine OEM Application Whirlpool / Maytag / Kenmore HE Top-Load Washers Voltage 120V AC Frequency 60 Hz Amperage 1.2A Duty Class CL.F Mounting 3 screws on underside of outer tub — tilt washer for access Compatible Brands Whirlpool, Maytag, Kenmore Installation Notes ⚠️ Unplug Washer and Shut Off Water Before Starting — Work Gloves Recommended Disconnect power and turn off the water supply before beginning. Wear work gloves throughout. The drain pump is mounted on the underside of the outer tub — to access it, disconnect the water supply hoses, drain hose, and lid switch wiring, then carefully tilt the washer onto its back or side on a padded surface. Locate the pump on the bottom of the tub. Using a 5/16" nut driver, remove the three mounting screws securing the pump assembly to the tub. Release the two spring clamps with channel-lock pliers and disconnect the inlet and outlet hoses from the pump. Disconnect the wiring harness and remove the old pump. Install the new W11396717 pump in the same position, reconnect hoses and clamps, reconnect the wiring harness, and secure with the three mounting screws. Return the washer to upright, reconnect all hoses and wiring, restore power and water, and run a drain/spin cycle to confirm drainage and check for leaks. Tools needed: Phillips screwdriver, 5/16" nut driver, channel-lock pliers, padded surface for tilting, work gloves. Frequently Asked Questions What is the difference between W11396717 and W11263349? These are the same drain pump assembly across two production revisions. W11263349 was the original part number, and W11396717 is the current updated version that supersedes it. Whirlpool issues updated part numbers when minor engineering changes are made during production. Both are the same pump with the same specifications, dimensions, and function. If your washer's parts diagram shows W11263349, the W11396717 is the correct current replacement to order. Why does accessing this pump require tilting the washer? On compatible Whirlpool WTW and Maytag MVW HE top-load washers, the drain pump is mounted directly to the underside of the outer tub — not on the cabinet side panel or behind a front access panel as on some other models. The pump's three mounting screws are only reachable from below the machine. The standard repair procedure is to unplug and disconnect the washer, tilt it onto its back or side on a padded surface, access the pump from underneath, and return the washer to upright after installation. How do I know if it's the drain pump versus a blocked drain hose? Before replacing the pump, check the drain hose for kinks or blockages — disconnect the hose and blow through it to confirm it is clear. Also check whether the drain hose standpipe height is within the recommended range (typically 39–96 inches from the floor). If the hose is clear and properly positioned but the washer still won't drain, listen during the drain phase: a completely silent drain cycle (motor not running) suggests a failed motor or control board issue, while a humming or grinding noise during drain confirms the pump motor is receiving power but the pump is mechanically failed and needs replacement. Is this pump the same as the W10876600 used in older Whirlpool Cabrio models? No — the W11396717 and the W10876600 are different drain pumps for different Whirlpool top-load washer generations. The W10876600 (and its successor WPW10730972) is used in older Whirlpool Cabrio and Maytag Centennial models. The W11396717 is used in newer WTW5100/6120/7120/8120 and MVW6200/6230/7230/7232/8230 series models. They are not interchangeable — verify your model number before ordering. Is this an OEM or aftermarket part? This is a Genuine OEM part manufactured by Whirlpool to factory specifications. It is the exact same drain pump assembly installed in compatible Whirlpool, Maytag, and Kenmore top-load washers from the factory — guaranteed fit, materials, and performance. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Genuine OEM Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

(4 Pack) 74009592CM Burner Control Knob Black plastic burner knob Fits Specific Maytag, Jenn Air, Whirlpool ranges Replaces Part Numbers: WP74009592, 74009592, 1032643, 71003477, AP6011140, PS11744334. Description: This Top Burner Control Knob is a replacement part for specific Whirlpool ranges and cooktop models. This part allows for precise control over the heat level of the stove's burners, enabling users to adjust the flame size for various cooking needs. Constructed from durable materials, the knob is designed to withstand the rigors of daily use, providing a reliable interface for setting and maintaining the desired cooking temperature. This is an aftermarket part that can be used as a replacement for the OEM part.

Read more less

W11688994 Washer Genuine OEM Water Valve Single water inlet valve, hot Replaces Part Numbers: W11688994, W11316255, W11036928, W11486360, AP7218602, PS17216729. Description: This Water Inlet Valve is a Genuine OEM part for specific Maytag, Kenmore, Whirlpool washing machine models. It controls the flow of water into the washer tub at designated stages in the washing process. Water enters through the valve inlet and is distributed to internal components like the detergent dispenser, water pipes, and sump hoses. Common causes of a bad valve can include mineral scale buildup inhibiting proper flow regulation over time, or cracks and leaks from wear and tear on rubber gaskets and seals. 

Read more less