WD26X25103 Genuine OEM GE Dishwasher Variable Wash Pump Kit
The WD26X25103 is a genuine GE OEM variable wash pump kit for premium GE, Café, GE Profile, Monogram, Hotpoint, and Haier dishwashers. The wash pump is the heart of the cleaning system — it draws filtered water from the sump and drives it under pressure through the lower spray arm, the middle spray arm, and the upper wash manifold. What makes this a variable pump is its variable-speed motor: instead of running at one fixed speed, the control board modulates pump speed throughout the cycle, ramping pressure up for heavy soil and down for delicate loads, and shifting flow between spray zones. That is why a failing variable pump often produces uneven results — the bottom rack comes out clean while the top rack is barely wet.
This is a complete kit, supplied with the circulation pump assembly and its integrated wiring harness, so you are not transferring connectors from the old unit. Typical failure modes include worn motor bearings that produce a loud humming or grinding during the wash portion of the cycle, a seized or debris-jammed impeller, a shaft seal that begins weeping water into the base pan and trips the flood switch, and electrical failure of the variable-speed motor windings. It directly replaces WD26X22789, AP6973120, PS12730515, and EAP12730515. This is a moderate DIY repair — most people budget 1–2 hours.
Quick Answer
The WD26X25103 Genuine OEM GE Variable Wash Pump Kit fixes GE, Café, GE Profile, Monogram, Hotpoint, and Haier dishwashers with dishes that come out dirty or gritty, a top rack that isn't getting wet, weak or no spray arm rotation, loud humming or grinding during the wash cycle, or water pooling in the base pan from a leaking pump seal. Variable-speed motor; kit includes pump assembly plus integrated wiring harness. Replaces WD26X22789, AP6973120, PS12730515, EAP12730515. Fits premium CDT865/CDT866, PDT845/PDT846/PDT855, and ZDT915/ZDT975 platforms — not the same pump as WD26X23258.
Common Problems This Part Fixes
Dishes not getting clean — food soil, grit, or film left behind after a full cycle
Top rack not getting wet or not getting cleaned while the bottom rack washes normally
Spray arms turning slowly or not turning at all — insufficient water pressure
Loud humming, whining, or grinding noise during the wash portion of the cycle
Dishwasher runs a full cycle quietly with no audible water circulation
Water pooling in the base pan under the dishwasher from a leaking pump shaft seal
Flood switch or leak sensor tripping and shutting the dishwasher down mid-cycle
Cleaning performance that has gradually declined over months as bearings wear
Pump motor humming but the impeller not turning — seized shaft or jammed impeller
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This dishwasher variable wash pump kit directly replaces the following OEM and cross-reference part numbers:
WD26X25103, WD26X22789, AGE25305, AP6973120, PD00054224, PS12730515, EAP12730515.
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This variable wash pump kit is compatible with select premium built-in dishwashers from the following brands:
GE and GE Profile dishwashers (PDT845, PDT846, and PDT855 series)
Café dishwashers (CDT865 and CDT866 series)
Monogram dishwashers (ZDT915 and ZDT975 series)
Hotpoint dishwashers (select GE-built models)
Haier dishwashers (select GE-platform models)
Verified model numbers include: CDT865SSJ0SS, CDT865SSJ2SS, CDT865SMJ0DS, CDT865SMJ2DS, CDT866P2M4S1, CDT866P3M4D1, CDT866P4M4W2, PDT845SSJ0SS, PDT845SSJ2SS, PDT845SMJ0ES, PDT845SMJ2ES, PDT845SBL2TS, PDT845SBL3TS, PDT845SFL3DS, PDT846SSJ0SS, PDT846SSJ2SS, PDT846SMJ0ES, PDT846SMJ2ES, PDT855SSJ0SS, PDT855SSJ2SS, PDT855SMJ0ES, PDT855SMJ2ES, PDT855SIJ0II, PDT855SIJ2II, PDT855SBL2TS, PDT855SBL3TS, PDT855SFL3DS, ZDT915SSJ0SS, ZDT915SSJ2SS, ZDT915SIJ0II, ZDT915SIJ2II, ZDT915SPJ0SS, ZDT915SPJ2SS, ZDT975SSJ0SS, ZDT975SSJ2SS, ZDT975SIJ0II, ZDT975SIJ2II, ZDT975SPJ0SS, and ZDT975SPJ2SS.
Note: GE uses several different circulation pumps across its dishwasher lineup, and they are NOT interchangeable. The WD26X25103 is the variable-speed pump used on premium CDT/PDT/ZDT platforms. It is not the same part as the WD26X23258 circulation pump (GDT695/PDT825 platforms) or the WD26X22518 pump (PDF820/GDT535/ADT521 platforms). Fitting the wrong pump can result in a physical mismatch at the sump or a harness that will not mate with your control board. Always verify your full model number — including the suffix — before ordering. Contact our support team with your model number if you're unsure.
Key Features
Genuine GE OEM part — factory-specified flow rate, impeller geometry, and motor control profile
Variable-speed motor allows the control board to modulate wash pressure by cycle and soil level rather than running at one fixed speed
Complete kit — includes the circulation pump assembly and integrated wiring harness, so no connectors need to be transferred from the old pump
Drives water through the lower spray arm, middle spray arm, and upper wash manifold
Resolves "dishes not clean," "top rack not getting wet," "spray arms not turning," "loud humming or grinding," and "water in the base pan" symptoms caused by pump failure
Sealed shaft design protects the motor from sump water intrusion
Direct drop-in replacement for the superseded WD26X22789 — no modifications required
Serves GE Profile, Café, Monogram, Hotpoint, and Haier premium dishwasher platforms
Replaces WD26X22789, AP6973120, PS12730515, and EAP12730515
Genuine OEM replacement — guaranteed fit, materials, and performance
Product Specifications
Part Number
WD26X25103
Part Type
Dishwasher Variable Wash Pump Kit (Circulation Pump)
Condition
Genuine OEM
Brand
GE Appliances
Motor Type
Variable speed
Voltage
120V / 60 Hz
Function
Circulates water under pressure to the spray arms and upper wash manifold
Kit Contents
Wash pump assembly + integrated wiring harness
Location
Underneath the tub, mounted to the sump housing
Connections
2 hose clamps + 2 electrical connections
Supersedes
WD26X22789
Repair Difficulty
Moderate — 1 to 2 hours
Quantity
1 pump kit
Compatible Brands
GE, GE Profile, Café, Monogram, Hotpoint, Haier
Installation Notes
⚠️ Disconnect Power And Shut Off Water Before Starting Turn off the dishwasher's circuit breaker and close the hot water supply valve under the sink before beginning. Wear work gloves — the tub edges and undercarriage brackets are sharp. Before condemning the pump, run a quick check: remove the lower spray arm and filter assembly, clear any glass chips, seeds, or labels from the sump, and confirm the spray arm ports are not blocked. A clogged filter screen produces the same "dishes not clean" complaint as a failing pump and costs nothing to rule out. To replace the pump, first remove the two screws securing the dishwasher to the underside of the countertop (or to the adjacent cabinets), disconnect the water line and drain hose, and slide the unit out. Most technicians then lay the dishwasher on its front or on its back to reach the pump — put a towel down to protect the door and finish. Photograph the hose routing and wiring before disconnecting anything. Release the two hose clamps and separate the two electrical connections, then unlock the pump from the sump housing — it typically twists to release from a bayonet-style mount — and lift it out. Inspect the sump gasket and seat while the pump is off; replace the gasket if it is hardened, flattened, or nicked. Install the new WD26X25103 in the same orientation, twist to lock, reattach both hoses with their clamps, and reconnect the harness. Reinstall the dishwasher, restore water and power, then run a full cycle and check underneath for leaks before pushing the unit all the way back and reattaching the mounting screws. Tools needed: Phillips screwdriver, nut driver, pliers or hose clamp pliers, towel, work gloves.
Frequently Asked Questions
My top rack isn't getting clean but the bottom rack is fine. Is that the wash pump?
It's the signature symptom of a weakening wash pump, yes — but check two cheaper things first. The upper wash manifold and the middle spray arm are fed last and at the lowest pressure, so they are the first zones to suffer when pump output drops. However, a clogged filter screen or a spray arm with blocked ports will starve the upper rack the same way. Pull the lower spray arm and filter, rinse them under hot water, poke a toothpick through any blocked spray ports, and run a cycle. If the top rack is still dry or dirty after that, the variable pump is losing pressure and should be replaced.
What does "variable" mean on this pump, and does it matter?
It matters a great deal. A variable-speed pump lets the control board change pump speed during the cycle — higher pressure for heavy soil, lower for delicate loads, and different speeds when directing flow to different spray zones. A fixed-speed pump cannot do that. This is why you cannot substitute a standard circulation pump from another GE platform even if it physically resembles this one: the control board expects a variable-speed motor and will not drive a fixed-speed unit correctly.
The dishwasher is making a loud grinding noise. Do I need the whole pump?
Not always — check for foreign objects first. Glass chips, fruit pits, bones, and hard plastic bits routinely get past the filter and rattle inside the pump housing or wedge against the impeller. Remove the filter assembly and inspect the sump thoroughly with a flashlight. If the sump is clean and the noise is a steady hum or grind that rises with the wash cycle, the pump's motor bearings are worn and the complete kit is the correct repair. Bearing noise does not improve on its own and usually precedes a shaft seal leak.
I found water in the pan underneath the dishwasher. Could the pump cause that?
Yes. When the pump's shaft seal wears out, it weeps water down onto the base pan during every wash cycle. GE dishwashers have a flood switch in that pan, so the machine will eventually detect the water and shut itself down mid-cycle or refuse to start. Before ordering, confirm the water is coming from the pump and not from a loose hose clamp, a cracked sump, or the door gasket — dry the pan completely, run a short cycle, and watch where the first drops appear.
Does this kit include everything, or do I need to reuse parts from the old pump?
The kit ships with the wash pump assembly and its integrated wiring harness, so you will not need to cut, splice, or transfer the electrical connector from your old pump. You will reuse your existing hoses and clamps. Inspect the sump gasket while the pump is out and replace it if it looks hardened, flattened, or nicked — a tired gasket is a common cause of a "new pump that still leaks."
What's the difference between WD26X25103 and WD26X22789?
They are the same pump across production revisions. WD26X22789 was the earlier number and WD26X25103 is the current GE part number that supersedes it. If your dishwasher's parts diagram shows WD26X22789, this listing is the correct replacement — order it with confidence. The additional cross-references (AP6973120, PS12730515, EAP12730515) are catalog identifiers used by various parts distributors for the same kit.
Is this an OEM or aftermarket part?
This is a genuine OEM part, manufactured by GE to factory specifications — guaranteed fit, materials, and performance. It matches the original variable-speed motor profile, impeller geometry, flow rate, sump mounting interface, and harness connector of the pump originally installed in your dishwasher, which is important on this platform because the control board is calibrated to drive a variable-speed pump.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
316490000 Oven Genuine OEM Temperature Sensor
Product Overview
The 316490000 Oven Genuine OEM Temperature Sensor is designed to accurately monitor oven temperature and ensure proper heating performance. This Oven Sensor Assembly is a Genuine OEM part for select Frigidaire oven models, designed to accurately measure the oven's internal temperature and communicate it to the control board. This ensures that the oven maintains the desired temperature setting during baking or roasting, providing consistent cooking results.
Quick Answer
If your oven is overheating, not heating properly, or showing incorrect temperature readings, the 316490000 temperature sensor may be faulty. Replacing it restores accurate temperature control and consistent cooking results.
Replaces Part Numbers
Replaces OEM part number: 316490000, 316490003, 1197392, 316490002, 612058426864, 7316490000, AH1528542, EAP1528542, AFR16190, PD00000483, OEM15854618, AP3963654, PS1528542.
Compatibility
This oven temperature sensor is compatible with select Frigidaire, Electrolux, Kenmore, and other compatible ranges and ovens.
Frigidaire Ranges & Ovens
Electrolux Appliances
Kenmore Ranges
Always verify your appliance model number before ordering.
Common Problems This Part Fixes
Oven overheating or under-heating
Inaccurate temperature readings
Uneven cooking results
Error codes related to temperature sensor
Key Features
Genuine OEM temperature sensor
Accurate temperature monitoring
Reliable and durable construction
Restores proper oven performance
Product Specifications
Part Number: 316490000
Part Type: Oven Temperature Sensor
Brand: OEM
Condition: New
OEM / Aftermarket: Genuine OEM
Application: Ovens & Ranges
Troubleshooting Guide
Oven too hot or too cold → Faulty temperature sensor
Food overcooking or under-cooking → Incorrect temperature readings
Error codes displayed → Sensor failure likely
When Should You Replace This Sensor?
Replace this sensor if your oven temperature is inconsistent, inaccurate, or if error codes indicate a sensor issue.
Installation Notes
⚠️ Disconnect power before installation. Remove mounting screws, disconnect wiring, and install the new sensor securely. Refer to your appliance manual if needed.
Related Parts
Oven Control Board
Heating Element
Thermostat Components
Frequently Asked Questions
Will this sensor fit my oven?This sensor fits many Frigidaire and compatible models. Always verify your model number.
What does an oven temperature sensor do?It monitors oven temperature and sends signals to maintain accurate heat levels.
What are signs of a bad sensor?Inconsistent temperatures, error codes, or improper cooking results.
Is this OEM?Yes, this is a genuine OEM temperature sensor.
Shop With Confidence
Parts-O-Matic is a U.S.-based appliance parts retailer specializing in OEM and high-quality replacement parts. We offer fast shipping, reliable products, and expert support.
Fast Shipping Genuine OEM Parts Compatibility Support
XPARTCO WH01X10060 Washer / Dryer Selector Knob – Compatible with GE & Hotpoint Laundry Units
Product Description
Restore smooth control and reliable operation with the XPARTCO WH01X10060 Washer / Dryer Selector Knob. This high-quality aftermarket replacement knob fits securely onto the selector switch shaft, allowing easy and precise cycle or function selection. A cracked, loose, or missing selector knob can make it difficult to operate your washer or dryer correctly. Replacing it with this durable XPARTCO knob helps restore normal operation and improves everyday usability.
XPARTCO is a trusted aftermarket brand offering appliance replacement parts built to OEM-equivalent specifications at a cost-effective price.
Replaces Part Numbers
WH01X10060, WH01X10140, 277248, WE01M0445, WE01X10142, WE01X10147, WE1M445, WE1X10142, WE1X10147, WH01X10107, WH01X10135, WH1X10060, WH1X10107, WH1X10135, WH1X10140, PD00001193, EAP268450, AH268450, EA268450, AP2044504, PS268450.
Compatibility
This replacement washer / dryer selector knob fits select GE and Hotpoint washers and dryers.
Commonly used on laundry units with rotary selector switches.
Always verify your appliance’s model number before ordering.Contact our support team if you’re unsure.
✅ Key Features
🔄 Aftermarket Replacement – Matches OEM fit and appearance
🎛️ Smooth Selector Control – Restores easy cycle or function selection
🧩 Direct-Fit Design – Push-on fit for secure installation
💪 Durable Plastic Construction – Built for repeated daily use
💰 Cost-Effective Repair – Affordable alternative to OEM knobs
📐 Product Specification
Part Number: WH01X10060
Component Type: Washer / Dryer Selector Knob
Material: High-strength molded plastic
Color: White (OEM-style)
Mounting: Push-on / shaft-fit
Quality Level: Aftermarket replacement (not OEM)
🛠️ Installation Notes
Tools Needed: None
⚠️ Safety First: Ensure the washer or dryer is powered off before installing the knob.
Basic Steps:
Turn the appliance off.
Align the new XPARTCO WH01X10060 knob with the selector shaft.
Press firmly until fully seated.
Rotate to confirm smooth operation.
⏱️ Time Required: Under 2 minutes
📦 Shop With Confidence
🚚 Free Shipping on All Orders
⚙️ Trusted Aftermarket Appliance Parts
🔄 30-Day Return Policy
Restore smooth control in seconds — Add to Cart Now for a quick, budget-friendly fix!
XPARTCO (2 Pack) EXP571 Dryer Door Catch
The XPARTCO (2 Pack) EXP571 is a two-pack of aftermarket replacement door catches for electric and gas dryers from Whirlpool, Maytag, Kenmore, Frigidaire, Electrolux, GE, Amana, Crosley, White-Westinghouse, and LG. The door catch is the small plastic part the dryer door latches onto to stay securely shut during a cycle. Keeping the door tightly closed holds heat and airflow inside the drum, so clothes dry efficiently. Over time, regular wear, physical damage, or a door that has drifted out of alignment can cause the catch to crack, wear down, or lose its grip, and the door stops latching reliably.
Made from durable plastic, this is a direct-fit replacement with a simple snap-in installation — no tools required. Because the same catch design was used across several appliance families, it carries a long cross-reference list spanning Whirlpool, Frigidaire, and GE part numbers; see the Replaces list below. Each order includes 2 door catches.
Quick Answer
The XPARTCO (2 Pack) EXP571 Dryer Door Catch fixes a dryer door that won't stay closed, won't latch properly, or pops open during a cycle because the catch is cracked, worn, or damaged. Durable plastic, snap-in install with no tools, 2 catches per order. Fits Whirlpool, Maytag, Kenmore, Frigidaire, Electrolux, GE, Amana, Crosley, White-Westinghouse, and LG dryers. Classic symptom: you have to push or hold the door shut, or it swings open mid-cycle and heat escapes.
Common Problems This Part Fixes
Dryer door won't stay closed or pops open during a cycle
Door doesn't latch with a firm, positive click
Visibly cracked, broken, or worn catch
Heat escaping around the door, leaving clothes damp after a full cycle
Door feels loose or misaligned when closed
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This door catch directly replaces the following part numbers:
WP71002106, WP3389441, 3389441, 71002106, AWP47565, PD00004499, AP6010685, PS11743869, AP6008299, PS11741434, WE1X1195, AGE1230465, AP2042209, PS266896, 131658800, AFR14189, AP2107362, PD00000626, PS418433, 5307521419, 10690002, 10690001, AFR14189, AP4450746, PD00000626, PS418433
This one catch design was sold under the part numbers of several manufacturers: Whirlpool/Maytag (WP71002106, WP3389441), Frigidaire/Electrolux (131658800, 5307521419), and GE (WE1X1195, WE1X1153, WE01X10023, and related). The AP/PS-prefixed numbers are third-party catalog cross-references for the same physical part.
Compatibility
This door catch is used on dryer models from the following brands:
Whirlpool, Maytag, Amana, and Kenmore (Whirlpool-built) dryers
Frigidaire, Electrolux, Crosley, White-Westinghouse, and Kenmore (Frigidaire-built) dryers
GE dryers
Select LG dryers
Note: Because this catch was used across so many brands and model years, a full model-number list can't be shown here. The safest way to confirm fit is to match the number on your old catch, or on your dryer's parts diagram, against the Replaces list above rather than relying on brand alone. Contact our support team with your model number and we'll verify before you order.
Key Features
Aftermarket replacement dryer door catch
Durable plastic construction for long-lasting use
Simple snap-in installation — no tools required
Holds the door securely closed to keep heat and airflow in the drum
Cross-references to Whirlpool, Frigidaire, GE, and other OEM numbering
2 door catches per order
Product Specifications
Part Number
EXP571 (2 Pack)
OEM Part Number
WP71002106, 131658800, WE1X1195
Part Type
Dryer Door Catch
Condition
Aftermarket Replacement
Material
Plastic
Quantity
2 Door Catches
Installation
Snap-In, No Tools Required
Application
Whirlpool, Maytag, Kenmore, Frigidaire, Electrolux, GE, Amana, Crosley, White-Westinghouse & LG Dryers
Installation Notes
ℹ️ No Tools Required Unplug the dryer before starting as a general safety precaution. Open the dryer door and locate the worn or broken catch the door latches onto. Pull or pry the old catch free from its mounting position, then press the new catch into the same opening until it snaps firmly into place. Close the door and confirm it latches with a positive click and stays shut. If the door still won't seat or latch evenly after the swap, check the door's alignment and hinges, since a misaligned door can wear out a new catch quickly.
Frequently Asked Questions
My dryer door won't stay shut — is this the part I need?
Very likely. A cracked, worn, or damaged door catch is a common reason a dryer door won't latch or pops open mid-cycle. Inspect the old catch for cracks or wear; if it looks damaged, replacing it should restore a firm latch.
Will this fit my dryer? I have a Whirlpool, Frigidaire, or GE.
This catch is cross-referenced to part numbers from all three families, plus several others. Match the number on your old catch or your dryer's parts diagram against the Replaces list above. If you're unsure, contact our support team with your model number and we'll confirm fit before you order.
Do I need tools to install it?
No. It's a simple snap-in design — remove the old catch and press the new one into place until it clicks.
How many catches come in this order?
Each order includes 2 door catches.
The door still doesn't close right after replacing the catch. What else could be wrong?
A door that has drifted out of alignment can keep a new catch from seating properly and wear it out fast. Check the door hinges and alignment against the cabinet opening.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout
W10919003 Washer Genuine OEM Drain Pump
Replaces Part Numbers: W10919003, 4461359, W10775446, AP6038235, PS11770076.
Description: This Water Pump is a Genuine OEM replacement part for specific Maytag, Kenmore, Whirlpool washing machine models. It plays a crucial role in circulating water throughout the wash cycles and draining the used water from the tub.
2 Pack - XPARTCO XPIBE1740 Microwave Light Bulb 40W Replaces 8206232A, WB25X10030
The XPARTCO XPIBE1740 is an aftermarket replacement 40-watt T8 appliance light bulb compatible with a wide range of microwaves, range hoods, refrigerators, ovens, and other kitchen appliances from GE, Whirlpool, KitchenAid, Maytag, Amana, LG, Frigidaire, Kenmore, Hotpoint, and more. It uses the standard E17 intermediate screw base found on most over-the-range and built-in microwave interior lights, range hood lights, and select appliance bulb sockets. With a clear T8 glass envelope, warm white 2800K color temperature, and 280-lumen output, it matches the brightness and look of the original OEM bulbs it replaces.
Specifications: 40W, 125V (AC 110-130V/60Hz), E17 intermediate screw base, T8 shape (1" diameter × 2-3/8" length), 280 lumens, warm white (~2800K), dimmable (compatible with microwave HIGH/LOW light settings), 1000-hour rated life, working temperature High Temp Resistance 300℃. It directly replaces 8206232A, 8206232, 8189961, 8204855, 8205422, 1890433, 0053437, 05200136, 05200137, AP4512653, R0712011, W10321375, W10598935, WB36X10003, WB25X10029, WB25X10030, WB25X10030-24PK, 261201500480, 3015548, 6912W1Z004B, AP5809052, PS2376034, and PS8767095. Installs in under 5 minutes — no tools required for the bulb itself.
Quick Answer
The XPARTCO XPIBE1740 Microwave Light Bulb (40W) replaces burned-out interior microwave lights, range hood lights, and select appliance bulbs across GE, Whirlpool, KitchenAid, Maytag, Amana, LG, Frigidaire, Kenmore, and Hotpoint. T8 shape, 40W, 125V, E17 intermediate screw base. 1" diameter × 2-3/8" length. 280 lumens warm white (~2800K). Dimmable. 1000-hour life. Replaces 8206232A, 8206232, 8189961, 8204855, 8205422, 1890433, AP4512653, R0712011, W10321375, W10598935, WB36X10003, WB25X10029, WB25X10030, WB25X10030-24PK, 6912W1Z004B, AP5809052, PS2376034, PS8767095. Make sure your appliance uses an E17 intermediate base — not E26 standard, E12 candelabra, or E14 European.
Common Problems This Part Fixes
Microwave interior light not working — bulb burned out
Range hood light bulb burned out — under-cabinet area no longer illuminates when cooking
Over-the-range microwave under-cabinet light not working
Bulb flickering or dimming inconsistently — filament starting to fail
Bulb visibly burned out, broken, or rattling when shaken (broken filament)
Microwave light works only intermittently — bulb on the verge of failure
Replacement after long service life — most appliance bulbs last about 2,000 hours
Replaces Part Numbers
This 40W appliance light bulb directly replaces the following OEM and cross-reference part numbers from multiple brands:
8206232A, 8206443, 8183993, 0053437, 05200136, 05200137, 14209237, 14210453, 14210811, 14218311, 14218312, 14218318, 1890433, 2635-0004, 2635-0005, 2665-0003, 4158344, 4158365, 4158432, 4164062, 4166665, 4174608, 4338831, 4359625, 4393681, 53001372, 53422, 53437, 56001071, 56001089, 57001073, 7-47000, 7-47001, 747000, 747001, 8189961, 8204855, 8205422, 8205586, 8206232, R0712013, R0712015, R0713503, R9900310, W10321375, W10598935, Y0053422, Y0053437, Y05200136, Y05200137, Y747000, Y747001, AWP39609, PD00003046, AH2376034, EA2376034, AP4512653, PS2376034, WB25X10030, 261201500480, 3015548, AGE22225 PD00034740, AP5809052, PS8767095, 26QBP4093.
If your bulb part number isn't listed above, check that the base is E17 intermediate and the bulb is 40W — most appliance bulbs in this category are interchangeable. Contact our support team if you need confirmation.
Compatibility
This 40W E17 appliance light bulb is compatible with a wide range of microwaves, range hoods, refrigerators, and ovens using E17 intermediate base sockets, including:
GE over-the-range and countertop microwaves (interior lights)
GE Profile, Café, and Monogram microwaves and range hoods
Whirlpool microwaves and range hoods (over-the-range models)
KitchenAid microwaves (built-in and over-the-range)
Maytag microwaves (select models)
Amana microwaves (select models)
LG over-the-range microwaves
Frigidaire microwaves and range hoods (select models)
Kenmore / Sears microwaves (multi-brand-built models)
Hotpoint microwaves and range hoods
Corningware microwaves (select models)
Also fits select refrigerator interior light sockets, oven lights, and lava lamps using the same E17 base
Important — Check Your Base Type: This bulb uses an E17 intermediate screw base. It will NOT fit appliances designed for E26 (standard household), E12 (candelabra), or E14 (European) bases. The E17 base is the most common base for over-the-range microwaves and range hoods, but check your old bulb or appliance manual to confirm before ordering. Some newer LG microwaves use a 30W bulb instead of 40W — verify your wattage requirement as well.
Key Features
40-watt T8 appliance incandescent bulb — replaces burned-out interior lights in microwaves, range hoods, refrigerators, and select ovens
Standard E17 intermediate screw base — fits the most common appliance bulb socket
T8 shape: 1" (25mm) diameter × 2-3/8" (62mm) length — matches OEM bulb dimensions for clear cover fit
125V (works on AC 110-130V / 60Hz household power)
400 lumens of warm white light (~2800K) — matches the brightness and color of original incandescent OEM bulbs
Dimmable — compatible with microwave HIGH/LOW light settings without flicker
1000-hour rated lifetime — standard for appliance incandescent bulbs
Working temperature range: High Temp Resistance 300℃. — suitable for microwave and range hood heat environments
Replaces 8206232A, 1890433, AP4512653, WB25X10030, WB36X10003, W10321375, W10598935, 6912W1Z004B, and many additional cross-references
Multi-brand cross-compatibility: GE, Whirlpool, KitchenAid, Maytag, Amana, LG, Frigidaire, Kenmore, Hotpoint, Corningware
Aftermarket replacement built to OEM-equivalent quality standards
Quick DIY replacement — installs in under 5 minutes
Product Specifications
Part Number
XPIBE1740
Common OEM Replacements
8206232A, WB25X10030, WB36X10003, 6912W1Z004B
Part Type
Appliance Light Bulb (Incandescent)
Condition
Aftermarket Replacement
Application
Microwave, Range Hood, Refrigerator, Oven, Appliance Lights
Wattage
40W
Voltage
125V (operates AC 110-130V / 60Hz)
Base Type
E17 Intermediate Screw Base
Bulb Shape
T8
Dimensions
1" (25mm) D x 2-3/8" (62mm) L
Brightness
280 lumens
Color Temperature
Warm White (~2800K)
Cover
Clear glass
Dimmable
Yes — compatible with HIGH/LOW microwave settings
Lifetime
over 2,000+
Working Temperature
High Temp Resistance 300℃.
Compatible Brands
GE, Whirlpool, KitchenAid, Maytag, Amana, LG, Frigidaire, Kenmore, Hotpoint, Corningware
Installation Notes
⚠️ Let the Bulb Cool Completely Before Touching — Unplug Microwave Before replacing the bulb, unplug the microwave (or disconnect power at the breaker for hardwired range hoods) and allow the old bulb to cool completely — incandescent appliance bulbs run very hot, and the glass can stay hot for several minutes after the light is turned off. For an over-the-range microwave's interior light, the bulb is typically accessed through a small panel or by removing a screw-on cover inside the microwave cavity. For under-cabinet/exterior lights, access the bulb by removing the protective cover or vent grille on the bottom of the microwave or range hood. Unscrew the old bulb counterclockwise and dispose of it safely. Screw in the new XPIBE1740 bulb clockwise — hand-tight only, do not over-tighten. Avoid touching the glass envelope of the new bulb with bare fingers; skin oils on the glass can shorten bulb life. If you must touch the glass, wipe it down with a clean cloth before powering the appliance back on. Replace the cover, restore power, and confirm the light works. Tools needed: none for most models, or a small Phillips screwdriver if a panel/cover must be removed.
Frequently Asked Questions
How do I know if I need an E17, E26, or E12 base bulb?
The "E" number refers to the screw base diameter in millimeters. E17 (intermediate) is 17mm — the most common size for over-the-range microwave interior lights, range hood lights, and many appliance lights. E26 (medium/standard) is 26mm — typical household light bulbs (do NOT fit appliance sockets). E12 (candelabra) is 12mm — used for chandelier and decorative bulbs. E14 (European intermediate) is 14mm — common in Europe but rare in U.S. appliances. The XPIBE1740 is an E17 intermediate base. If your old bulb is noticeably smaller or larger than what you're holding, it's the wrong base — confirm by comparing dimensions or checking your appliance manual before ordering.
Can I use an LED bulb instead of this incandescent one?
In many appliances, yes — LED appliance bulbs with E17 intermediate bases are available and use significantly less power for similar brightness. However, LED bulbs sometimes have compatibility issues with the dimming/HIGH-LOW settings on microwaves, can flicker, or may not work with the appliance's lighting control circuit. The XPIBE1740 incandescent bulb is fully dimmable and a guaranteed direct match to the original appliance bulb's behavior. If you prefer LED for energy savings, confirm the LED is rated for appliance use, has an E17 base, and is dimmable for microwave applications before substituting.
My LG microwave's bulb says 30W — does this 40W bulb fit?
Physically, yes — both the 30W and 40W bulbs use the same E17 intermediate base and similar T8 shape. However, some LG microwave models specifically call for a 30W bulb (such as the 6912W1Z004B variant). Using a 40W bulb in a socket rated for 30W may cause the bulb to run hotter than designed, shortening its life or the surrounding socket components' life. Check your LG microwave's manual or the marking on the old bulb — if it specifies 30W, use a 30W bulb. The XPIBE1740 is 40W, suitable for the majority of microwaves that specify 40W bulbs.
Why do appliance bulbs burn out faster than regular household bulbs?
Appliance bulbs operate in harsher environments than typical household bulbs — high temperatures (microwaves and range hoods can hit 480°F nearby), heavy vibration from cooking appliances, repeated rapid on-off cycling, and frequent thermal shock from cooking steam. Even though they're rated for 1,000 hours of operation, real-world life in an appliance is often shorter than the same incandescent bulb in a household lamp. Buying multi-packs and replacing when one burns out is a common approach. Always allow the appliance to cool before swapping the bulb, and don't touch the new glass with bare fingers to maximize service life.
Is this an OEM or aftermarket part?
This is an aftermarket replacement bulb built to OEM-equivalent quality standards. It is not a branded GE, Whirlpool, or LG OEM bulb, but is manufactured to match the dimensions (T8, 1" × 2-3/8"), electrical specifications (40W, 125V, E17 base), brightness (400 lumens, warm white), and dimmable performance of the original appliance bulbs it replaces. Bulb spec compatibility (not brand) is what determines fit, so a properly specified aftermarket bulb performs identically to the OEM.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout
Genuine GE OEM Part
GE WD24X25325 Dishwasher Genuine Fan Vent Assembly
Genuine GE door-vent blower/fan assembly for select GE and Haier dishwashers.
Product Overview
The GE WD24X25325 Dishwasher Fan Vent Assembly is a genuine OEM replacement used in the dishwasher door ventilation system.
The blower circulates air through the door vent during the drying portion of the cycle to help reduce retained moisture and improve drying performance.
Quick Answer
WD24X25325 is a Genuine GE OEM dishwasher door-vent blower/fan motor assembly. It is used on select GE and Haier dishwashers and helps move moist air through the door vent during drying.
Common Problems This Part May Fix
Poor drying performance
Excess moisture remaining after a cycle
Door vent fan does not run
Unusual noise from the vent/blower area
Moist air is not being exhausted through the door vent
Replaces and Cross-References
WD24X25325, 265D2664G005, U40G12BS3A5-51, AGE25072, AP6972063, EAP12726435, PD00073154, PS12726435.
Cross-reference numbers are supplied for identification. Always verify the complete dishwasher model number before ordering.
Compatibility
Fits select GE and Haier dishwashers. Compatible model examples include:
CDT800P2N0S1
CDT805P2N0S1
CDT845P2N3S1
DDT700SBN0TS
GDF645SSN0SS
GDT645SFN3DS
GDT665SFN0DS
GDP665SYN3FS
PDT715SYN2FS
PDT715SFN0DS
PDP715SYN3FS
QDP555SYN0FS
Important: This is only a partial compatibility list. Confirm the exact dishwasher model number before purchase because similar models may use a different vent or blower assembly.
Key Features
Genuine GE Appliances OEM part
Complete door-vent blower/fan assembly
Circulates air through the dishwasher door vent
Helps reduce moisture during drying
For select GE and Haier dishwashers
Product Specifications
Manufacturer
GE Appliances
Manufacturer Part Number
WD24X25325
Part Type
Dishwasher Fan Vent / Door Vent Blower Assembly
Condition
New
Part Quality
Genuine OEM
Application
Dishwasher Door Ventilation / Drying System
Approx. Shipping Weight
0.5 lb
Installation Notes
Disconnect electrical power to the dishwasher at the breaker before service.
Access the door vent assembly according to the appliance service procedure.
Disconnect the wiring connector carefully before removing the old fan assembly.
Transfer or reuse any hardware only as directed for the specific model.
Confirm the vent path is clear and the new assembly is fully seated before reassembly.
Diagnostic note: Poor drying can also result from rinse-aid settings, heating-system faults, blocked vent passages, or control issues. Confirm the fan assembly is defective before replacing it.
Frequently Asked Questions
Is WD24X25325 a Genuine GE OEM part?
Yes. GE Appliances identifies WD24X25325 as a genuine replacement fan vent assembly.
What does this fan assembly do?
It circulates air through the dishwasher door vent to help reduce moisture during the drying stage.
Does it fit every GE dishwasher?
No. It fits specific GE and Haier models. Verify the complete model number before ordering.
Is this only the fan motor?
This listing is for the complete WD24X25325 fan vent / door-vent blower assembly as supplied by GE.
Shop With Confidence
Use your dishwasher's complete model number to confirm fitment before purchase.
Genuine GE OEMFan Vent AssemblyModel Verification RecommendedFast U.S. Shipping
EXP572 Dryer Door Catch – Aftermarket Replacement for Whirlpool, Kenmore, Maytag, GE, Hotpoint
Product Overview
This Door Catch is a replacement part for specific GE, Hotpoint dryer models. It includes the door catch. This part ensures the dryer door remains securely closed during operation, preventing heat loss and ensuring the appliance functions efficiently. Common causes of a bad door catch include regular wear and tear, physical damage, or misalignment of the door, which can impact the catch's ability to latch properly
Replaces Part Numbers
WE1M1011, PS3502777, AP5324728, WE01M0197, WE01X0889, WE01X0903, WE01X1032, WE1M187, WE1M197, WE1M536, WE1X1032, WE1X889, WE1X903. It provides a reliable fit and function similar to OEM components.
Fixes the Following Issues
Dryer door won’t stay closed
Dryer doesn’t start
Door pops open mid-cycle
Worn or damaged door catch
Compatible Brands
Compatible with dryers made by Whirlpool, Kenmore (Whirlpool-built), Maytag, Amana, Roper, Estate, GE and Crosley. Suitable for many front-load and top-load residential models.
Why Buy from Parts-O-Matic
High-quality, durable replacement part
Always Fast and Free U.S. shipping
Easy to install – no special tools required
Trusted by appliance repair professionals and DIYers
XPARTCO 6501KW2001B Washer Rotor Positioning Sensor
The XPARTCO 6501KW2001B is an aftermarket replacement rotor position sensor (RPS) compatible with a wide range of LG and Kenmore direct-drive front-load washers. This 5-pin Hall effect sensor mounts to the motor stator and monitors the speed and rotational direction of the motor rotor, feeding that data back to the control board so it can properly manage spin speed, direction changes during wash/rinse agitation, and load balancing.
When this sensor fails or reads inaccurately, the control board loses the feedback it needs to run the motor correctly, and the washer commonly throws an "LE" (motor/rotor position) error code, fails to spin or agitate, or runs unusually long cycles as it struggles to detect motor movement. Built with PBT-GF30 housing and black epoxy potting for durability in the motor compartment. It directly replaces 6501KW2001A, 6501KW2001D, AP5973402, PS11706506, EAP11706506, and 3282954. Installs in 30–60 minutes with basic hand tools.
Quick Answer
The XPARTCO 6501KW2001B Washer Rotor Positioning Sensor fixes LG and Kenmore (LG-built) direct-drive front-load washers throwing an "LE" error code, failing to spin or agitate, or running abnormally long cycles. 5-pin Hall effect sensor, PBT-GF30 housing, black epoxy potting. Replaces 6501KW2001A, 6501KW2001D, AP5973402, PS11706506, EAP11706506, 3282954. Classic symptom: washer displays "LE" and stops mid-cycle, or won't spin at all.
Common Problems This Part Fixes
Washer displays an "LE" (motor/rotor position) error code
Tub fails to spin or agitate during the wash cycle
Washer struggles to detect load movement, resulting in abnormally long cycle times
Motor runs erratically or stalls mid-cycle
Washer stops partway through a cycle without completing
Inconsistent or failed direction changes during agitation
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This rotor position sensor directly replaces the following OEM and cross-reference part numbers:
6501KW2001B, 6501KW2001A, 6501KW2001D, PD00001726, EAP2497738, 6501KW2001C, EBR37560301, ALG52243, AP4457567, AP5973402, EAP11706506, 3282954, PD00059513, PS3529185, PS11706506
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This rotor position sensor is compatible with select LG-built direct-drive front-load washers, including:
LG front-load washers (including WM1814CW, WM2010CW, WM2016CW, WM3455HW)
Kenmore front-load washers (select LG-built models, including WD-3243RHD, WD-3245RHD, WD-3274RHD)
Important: Do not confuse this with 6501KW2002B, which is a different, non-interchangeable rotor position sensor used on other LG washer platforms. Some newer LG models also integrate the Hall sensor directly into the motor stator assembly (such as AJB73816004) rather than using a standalone sensor like this one. Always verify your appliance model number before ordering, and check your parts diagram to confirm whether your model uses a standalone sensor. Contact our support team with your model number if you're unsure.
Key Features
Direct-fit replacement LG/Kenmore washer rotor position sensor (Hall effect, 5-pin)
Resolves "LE error code," "won't spin," "won't agitate," and "long cycle time" symptoms
Monitors motor rotor speed and rotational direction for accurate control board feedback
PBT-GF30 housing with black epoxy potting for durability in the motor compartment
Replaces 6501KW2001A, 6501KW2001D, AP5973402, PS11706506, EAP11706506, and 3282954
Compatible with select LG and Kenmore (LG-built) direct-drive front-load washers
Aftermarket replacement built to OEM-equivalent quality standards
Product Specifications
Part Number
XP6501KW2001B
OEM Part Number
6501KW2001B
Part Type
Washer Motor Rotor Position Sensor
Condition
Aftermarket Replacement
Sensor Type
Hall Effect, 5-Pin
Housing Material
PBT-GF30 with black epoxy potting
Application
LG-Built Direct-Drive Front-Load Washer Motor Assembly
Compatible Brands
LG, Kenmore
Installation Notes
⚠️ Unplug Washer Before Starting Disconnect power before beginning. Access the motor compartment, typically by removing the rear panel of the washer. Locate the rotor position sensor mounted to the motor stator near the rotor. Photograph the wiring before disconnecting, then unplug the sensor's connector from the wiring harness. Remove the mounting screw(s) or clip holding the sensor to the stator and remove the old sensor. Install the new 6501KW2001B sensor in the same position, taking care to seat it at the correct distance/orientation from the rotor magnets, and secure it. Reconnect the wiring harness connector, matching your photos. Reinstall the rear panel, restore power, and run a test cycle to confirm the washer spins and agitates normally without triggering an LE error code. Tools needed: nut driver or screwdriver, needle-nose pliers (for wiring connectors).
Frequently Asked Questions
My washer shows an "LE" error code — is this the part I need?
This is one of the most common causes of an LE (motor/rotor position) error on LG and LG-built Kenmore washers. If your washer displays LE and stops mid-cycle or won't spin, this sensor is a likely culprit. That said, LE errors can also stem from the control board or a damaged wiring harness between the sensor and the board, so if replacing the sensor doesn't resolve the error, those components are the next things to inspect.
Is this the same as the 6501KW2002B sensor?
No — 6501KW2001B and 6501KW2002B are different, non-interchangeable rotor position sensors used on different LG washer platforms. Confirm your exact part number from your appliance's parts diagram before ordering, since these two are easy to mix up by their similar naming.
My LG washer's parts diagram doesn't show a separate rotor position sensor — why?
Some newer LG models integrate the Hall sensor directly into the motor stator assembly (such as part AJB73816004) rather than using a standalone sensor like this one. If your model doesn't list a standalone sensor, check whether your repair requires the full stator assembly instead. Contact our support team with your model number if you're unsure which one applies to your washer.
Do I need any special tools to install this?
No special tools — a nut driver or screwdriver to access the rear panel and remove the sensor's mounting screw(s), plus needle-nose pliers to help with the wiring connector. The main thing to get right is reinstalling the new sensor at the same position and orientation relative to the rotor as the original.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout
WP4449751 Genuine OEM Whirlpool Oven High Limit Thermostat
The WP4449751 is a Genuine OEM Whirlpool replacement oven high limit thermostat compatible with a wide range of Whirlpool, KitchenAid, Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore ovens, wall ovens, microwave-oven combinations, and ranges. The high limit thermostat is a critical safety device mounted near the oven cavity — it continuously monitors the oven's temperature and cuts off electrical power to the heating element if the oven exceeds its safe operating temperature. When the oven temperature drops back to normal, the thermostat closes and allows normal operation to resume. This backup safety layer protects against fires, damage to the oven, and unsafe cooking conditions when the main temperature control fails.
Rated to trip at approximately 335°F (170°C). Common causes for the high limit thermostat to trip include a faulty control board, cooling fan failure, blocked ventilation, poor door sealing, disrupted air circulation, or an abnormal self-cleaning cycle. As a Genuine OEM part manufactured by Whirlpool to factory specifications, the WP4449751 directly replaces 4449751, 1550872, AP6009390, AH2375382, EA2375382, PS2375382, PS11742549, EAP11742549, and AH11742549. Installs in 30–45 minutes with basic hand tools by experienced DIYers. This is a safety component in a 240V oven circuit — proceed only if you're comfortable with high-voltage electrical work, or call a qualified appliance technician.
Quick Answer
The WP4449751 Genuine OEM Whirlpool Oven High Limit Thermostat fixes Whirlpool, KitchenAid, Maytag, Jenn-Air, Amana, and Kenmore ovens with symptoms including oven not heating, oven overheating, uneven heating, oven failing to start, and self-clean door won't unlock after cycle. 335°F (170°C) trip temperature — cuts off power to heating element on overheat, then resets when temperature returns to normal. Genuine OEM. Replaces 4449751, 1550872, AP6009390, AH2375382, EA2375382, PS2375382, PS11742549, EAP11742549, AH11742549. Compatible with WOS/WOD wall ovens, KOSE/KODE/KOCE series, JJW/JMW/JDRP/JDR series, and many more.
Common Problems This Part Fixes
Oven not heating at all — high limit thermostat tripped open
Oven overheating — thermostat failing to trip when needed (rare failure mode)
Inconsistent oven temperatures leading to undercooked or overcooked food
Oven fails to start when powered on
Oven door won't unlock after a self-cleaning cycle completes
Uneven heating — hot spots or cold spots inside the oven cavity
Oven cuts off heat mid-cycle without reaching set temperature
F-code or thermostat-related error displayed on the control panel
Multimeter continuity test on the thermostat shows an open circuit at room temperature
Visible damage or discoloration on the thermostat housing from a prior overheat event
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This oven high limit thermostat directly replaces the following OEM and cross-reference part numbers:
WP4449751, 4449751, 1550872, AP6009390, AWP47600, EAP2375382, PD00025977, PS11742549
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This high limit thermostat is compatible with select ovens, wall ovens, ranges, and microwave-oven combinations from the following brands:
Whirlpool wall ovens — WOS series (WOS31ES0JS, WOS51EC0AS, WOS51EC0HS, WOS51EC7HW02, WOS51EC7HW21, WOS72EC0HS/HV, WOS72EC7HS/HV, WOS92EC0/EC7 all revisions, WOS97ES0ES series)
Whirlpool double wall ovens — WOD series (WOD51EC0AW03, WOD51EC7HS, WOD93EC7AS)
Whirlpool combination wall ovens — WOC54EC0/EC7 series
KitchenAid wall ovens — KOSE, KODE, and KOCE series (KOSE500ESS, KODE500ESS, KOCE500ESS, KOCE500EBL00/EBL01/EBL02/EBL04/EBL05)
Jenn-Air wall ovens — JJW, JMW, JDRP, and JDR series (JJW2427DB/DS 00/01, JJW2430DS, JJW3430DS, JMW2430DS, JDRP430HL/HM 00/01, JDRP430WP00, JDRP436HL/HM/WP series, JDRP536HL/HM/WP series)
Maytag wall ovens and ranges (select models)
Amana wall ovens (select models — AWO6313SFB00/02, AWO6313SFS00/02, AWO6313SFW00/02)
KitchenAid ranges — KDRS407 series (KDRS407VBK01, KDRS407VBU01, KDRS407VSS00)
Whirlpool ranges — IBD350DS00, IBS300DS00, IBS350DS00 series
Magic Chef, Admiral, Norge, Roper wall ovens (select Whirlpool-built models)
Kenmore / Sears wall ovens (select Whirlpool-built models)
Suitable for single or double electric wall ovens and microwave-oven combination units
Always verify your appliance model number before ordering. Contact our support team if you're unsure.
Key Features
Genuine OEM part manufactured by Whirlpool to factory specifications — guaranteed fit and performance
High limit thermostat (safety switch) — cuts off power to the oven's heating element when temperature exceeds 335°F (170°C) to prevent overheating damage or fire
Auto-reset design — closes and restores normal operation when the oven temperature returns to safe range
Precision-calibrated to Whirlpool factory specifications for accurate trip temperature and reliable safety response
One-year Whirlpool warranty on Genuine OEM parts
Replaces 4449751, 1550872, AP6009390, AH2375382, EA2375382, PS2375382, PS11742549, EAP11742549, and AH11742549
Compatible with Whirlpool WOS/WOD/WOC series, KitchenAid KOSE/KODE/KOCE series, Jenn-Air JJW/JMW/JDRP/JDR series, plus Maytag, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore ovens
Fits single wall ovens, double wall ovens, ranges, and microwave-oven combination units
Resolves "oven won't heat," "overheating," "uneven heating," "self-clean door stuck locked," and "won't start" symptoms when caused by a failed high limit thermostat
For experienced DIYers or qualified appliance technicians — this is a safety component in a 240V oven circuit
Installation typically takes 30–45 minutes with basic hand tools
Product Specifications
Part Number
WP4449751
Part Type
Oven High Limit Thermostat (Safety Switch)
Condition
Genuine OEM
Application
Wall Ovens, Ranges, Microwave-Oven Combinations (Whirlpool platform)
Trip Temperature
335°F (170°C)
Type
Auto-Reset (closes when temperature returns to safe range)
Warranty
One-Year Whirlpool Warranty (Genuine OEM)
Compatible Brands
Whirlpool, KitchenAid, Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, Kenmore
Installation Notes
⚠️ Turn Off Power at Breaker Before Starting — This Is a 240V Oven Circuit — Wear Work Gloves Disconnect power at the household breaker before beginning — this is a 240V circuit and there is a serious risk of electrical shock if power is not fully disconnected. Verify power is off with a voltage tester before touching any wiring. Wear work gloves and safety glasses. Allow the oven to cool completely before beginning (several hours after any recent cooking). The high limit thermostat is typically mounted on the rear or side of the oven cavity, accessed by removing the back panel of the appliance (for freestanding ranges) or the front trim/service panel (for wall ovens). The exact location varies by model — consult your appliance's service diagram before starting. Photograph all wire connections and mounting details before disconnecting anything. Disconnect the wire terminals from the old thermostat (typically two spade-terminal wires). Remove the mounting screws or clips holding the thermostat to the oven cavity, and lift it out. Install the new WP4449751 in the exact same position and orientation — the thermostat must be in good thermal contact with the oven cavity to function correctly. Secure the mounting hardware and reconnect the wires to their correct terminals. Reinstall the access panels. Restore power at the breaker and test the oven — start with a low-temperature bake cycle to confirm normal heating operation before running a high-temperature or self-clean cycle. Tools needed: Phillips screwdriver, 1/4" nut driver, voltage tester (essential), work gloves, safety glasses.
Frequently Asked Questions
Why did my high limit thermostat trip in the first place?
A high limit thermostat trips because the oven exceeded its safe operating temperature — meaning something upstream in the temperature control chain failed to shut off the heating element when it should have. Common causes are: a failed oven control board (relay stuck closed), a failed cooling fan (allowing the oven cavity or electronics to overheat), blocked or restricted ventilation, poor door sealing (letting the cavity overheat), disrupted air circulation, or an abnormal self-cleaning cycle. Before installing the new thermostat, investigate and address the underlying cause — otherwise the new thermostat will trip again in short order. Also inspect the ventilation, oven door gasket, and cooling fan while you have the appliance open.
What's the difference between a high limit thermostat and the operating thermostat?
These are two different components serving two different roles. The operating thermostat (or the oven control board with its temperature sensor) is the primary component that maintains the oven at your set temperature by cycling the heating element on and off during normal operation — it opens and closes at your selected temperature (e.g., 350°F). The high limit thermostat (WP4449751) is a backup safety device that only trips when the oven temperature far exceeds normal operation (335°F over the cavity's safe threshold), typically because the operating thermostat or control has failed. If the high limit thermostat trips, both need to be checked — the operating thermostat may also need replacement.
Does the high limit thermostat reset itself, or does it need to be replaced after tripping?
The WP4449751 is an auto-reset thermostat — it closes automatically once the oven cools back to a safe temperature, allowing normal operation to resume. If your oven is heating normally again after cooling, the thermostat is likely still functional (the underlying overheating cause needs investigation). However, if the thermostat has failed permanently open — often the result of repeated overheat events or age — it will need replacement. Test with a multimeter set to continuity: a working thermostat shows continuity at room temperature. If it reads open (infinite resistance) when cold, it has failed and needs replacement.
Why does my self-cleaning cycle leave the oven door locked and the oven won't heat?
This is a classic symptom of a high limit thermostat that tripped during the self-clean cycle. Self-cleaning cycles run at extreme temperatures (800–1000°F) and stress every component in the oven — if the ventilation, door gasket, or cooling fan can't keep up, the high limit thermostat will trip open. Once tripped, the oven can't heat OR unlock the self-clean door lock mechanism, leaving the door stuck closed. Once the thermostat cools and closes (or is replaced), the door lock releases and normal operation resumes. If self-clean cycles routinely trip the thermostat, investigate whether the ventilation, cooling fan, or door gasket are causing the problem.
Can I do this repair myself, or should I hire a technician?
Replacing an oven high limit thermostat is a manageable DIY repair for someone comfortable with mechanical work and electrical connections, but this is a 240V circuit and the thermostat is a safety component — any error can create a serious safety risk. If you have experience with appliance repair, follow the safety precautions carefully (breaker off, voltage tester, correct thermostat orientation), and can confirm the wiring connections are secure, this is a feasible DIY. If you've never worked with 240V appliance circuits before, hiring a qualified appliance technician is the safer option. Also identify and address whatever caused the original overheat event — otherwise the new thermostat will trip again.
Is this a Genuine OEM or aftermarket part?
This is a Genuine OEM part manufactured by Whirlpool to factory specifications. It is the exact same high limit thermostat installed in compatible Whirlpool, KitchenAid, Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore ovens from the factory — guaranteed fit, materials, and performance. Backed by Whirlpool's one-year warranty on Genuine OEM parts.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
XPARTCO 12138200000320 Dryer Door Catch
The XPARTCO 12138200000320 is an aftermarket replacement dryer door catch compatible with select Midea and Insignia dryers. The door catch is a small plastic spring-clip mechanism mounted on the dryer door that snaps over the door strike o12138200000320 n the cabinet opening to hold the door firmly closed during operation. When the door is closed and latched, the door switch is activated — signaling the control board that it is safe to run. When the catch breaks, cracks, or loses its spring tension, the door will not stay closed, the door switch will not activate properly, and the dryer will either not start or will stop mid-cycle.
This is a snap-in replacement catch — the color or exact finish may vary by production run. It directly replaces AP7152622 and PS18161385. Sold individually. Installs in under 5 minutes — no tools required in most cases.
Quick Answer
The XPARTCO 12138200000320 Dryer Door Catch fixes Midea and Insignia dryers where the door won't stay closed, pops open during a cycle, or where the dryer won't start because the door switch isn't being activated. Snap-in installation — no tools required, installs in under 5 minutes. Sold individually. Replaces AP7152622, PS18161385.
Common Problems This Part Fixes
Dryer door will not stay closed during the drying cycle
Door pops open mid-cycle, stopping the dryer
Dryer will not start — door switch not being activated by a worn or broken catch
Door feels loose or does not click shut firmly when closed
Door catch visibly cracked, broken, or missing
Dryer requires the door to be held or pushed to stay running
Replaces Part Numbers
This door catch directly replaces the following part numbers:
12138200000320, AP7152622, PS18161385.
Contact our support team with your model number if you need confirmation before ordering.
Compatibility
This door catch is compatible with select dryers from the following brands:
Midea dryers (gas and electric — select models)
Insignia dryers (select models)
Always verify your appliance model number before ordering. Contact our support team if you're unsure.
Key Features
Holds the dryer door closed and activates the door switch so the dryer can run safely
Snap-in installation — no tools required in most cases; installs in under 5 minutes
Durable plastic construction — designed to withstand repeated opening and closing
Sold individually — one door catch per order
Replaces AP7152622 and PS18161385
Aftermarket replacement built to OEM-equivalent quality standards
Product Specifications
Part Number
12138200000320
Part Type
Dryer Door Catch (Door Latch Clip)
Condition
Aftermarket Replacement
Application
Gas and Electric Dryers
Material
Plastic
Installation
Snap-in — no tools required
Sold As
Single door catch
Compatible Brands
Midea, Insignia
Installation Notes
⚠️ Unplug Dryer Before Starting Disconnect power before beginning. Open the dryer door and locate the old door catch — it is a small plastic clip mounted on the inside of the door or on the cabinet opening around the door. Press the tabs on the old catch to release it from its mounting slot and pull it free. Note the orientation before removing. Insert the new 12138200000320 catch into the slot in the same orientation and press firmly until it snaps into place. Close the door to confirm it latches securely. Restore power and run a short cycle to verify the door stays closed and the dryer operates normally. Tools needed: None in most cases; a small flat-head screwdriver may help with removal.
Frequently Asked Questions
What dryers is the 12138200000320 compatible with?
The 12138200000320 door catch is used on select Midea and Insignia dryer models. Insignia is a Best Buy house brand whose appliances are manufactured by Midea. Always verify your exact model number before ordering to confirm this catch fits your dryer's door latch assembly.
Why won't my dryer start even though I'm closing the door?
If the door catch is broken or worn, the door may not be engaging the door switch firmly enough to signal the control board that the door is closed. Most dryers will not run unless the door switch is fully activated. Replacing the 12138200000320 catch restores the firm snap needed to trigger the switch. If replacing the catch does not resolve the start issue, the door switch itself may also need to be checked.
Do I need to replace the door strike as well?
Not necessarily. In most cases only the door catch (the spring-clip on the door) needs replacement. The door strike (the post or tab on the cabinet that the catch snaps onto) is typically more durable. Inspect the strike for cracks or breakage before ordering — if it is intact, just the 12138200000320 catch is all you need.
Is this an OEM or aftermarket part?
This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Midea OEM part, but is manufactured from durable plastic to match the dimensions and function of the original 12138200000320 door catch.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout
