Search results for "refrigerator switch"

W11568627 Genuine OEM Whirlpool/Kenmore Dryer Drum Belt The W11568627 is a genuine OEM drum (cylinder) belt for select Whirlpool and Kenmore front-load dryers. This belt wraps around the outside of the drum and routes around the drive motor pulley and idler pulley — it's what actually spins the drum during a drying cycle while the motor and blower keep running independently. Over time this belt stretches, glazes, or cracks from heat and friction, and it eventually slips or snaps, leaving the drum motionless even though the rest of the dryer still runs. Manufactured by Whirlpool to factory spec for smooth, durable drum operation under high-demand drying cycles, this is a genuine OEM part — not an aftermarket equivalent — so fit and long-term performance match what came on the dryer originally. Quick Answer The Genuine OEM W11568627 Dryer Drum Belt fixes a Whirlpool or Kenmore dryer whose drum won't spin, or that runs with a rubbing/thumping noise from the drum area. Genuine OEM replacement, factory fit. Classic symptom: motor and airflow run normally, but the drum sits still — or a rubbing sound right before the belt fails completely. Common Problems This Part Fixes Dryer runs (motor and airflow work) but the drum doesn't spin Rubbing, squealing, or thumping noise from inside the dryer during operation Clothes bunch up in one spot instead of tumbling Burning rubber smell from a slipping or overheating belt Visible cracking, glazing, or fraying on the old belt Dryer drum spins freely by hand with no resistance from the motor Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This drum belt directly replaces the following part number: W11568627, W10577771, AP7175918, AWP45299, EAP16660508, OEM21527763, PD00070745, PS16660508 W10577771 is the previous Whirlpool part number for this belt; W11568627 is the current production number. We were not able to confirm additional cross-reference numbers beyond these two at this time. If you have one, contact our support team before ordering and we will verify compatibility. Compatibility This drum belt is compatible with the following Whirlpool and Kenmore dryer models: 11061632610, 11061632611 11061633610, 11061633611, 11061633612 11071632610, 11071633610, 110C61633610 WED9500EC0, WED9500EW0, WGD9500EC0, WGD9500EW0 Note: Not all applicable models are necessarily listed above — this is the compatibility data we were able to confirm from available sourcing, and Whirlpool may use this belt on additional models not shown here. Confirm the belt shown on your dryer's parts diagram matches this part number, or contact our support team with your model number to verify before ordering. Key Features Genuine OEM drum belt — factory fit and durability, not an aftermarket equivalent Drives drum rotation during the drying cycle Built for smooth, reliable operation under high-demand drying cycles Resolves drum-not-spinning, rubbing/thumping noise, and slipping-belt symptoms Direct replacement for both W11568627 and the earlier W10577771 numbering One-year manufacturer replacement warranty on genuine parts Product Specifications Part Number W11568627 OEM Part Number W11568627 Part Type Dryer Drum (Cylinder) Belt Condition Genuine OEM Application Whirlpool & Kenmore Dryers Country of Origin Mexico Installation Notes ℹ️ Unplug Power Before Installing Unplug the dryer or switch off its circuit breaker before beginning. Remove the dryer's front or rear access panel per your model's service guide to reach the drum, motor pulley, and idler pulley. Release tension on the idler pulley to slip the old belt off, and note the belt's routing path around the drum and pulleys before removing it — a photo taken beforehand makes reinstallation much easier. Loop the new belt around the drum with the ribbed side against the drum surface, then route it around the motor pulley and back around the idler pulley in the same path as the original, making sure it isn't twisted. Reinstall the idler pulley to restore proper tension, then rotate the drum by hand to confirm the belt tracks straight and doesn't rub before closing up the panel. Frequently Asked Questions My dryer runs but the drum won't turn — is this the part I need? Yes, in most cases. A broken or badly slipped drum belt is the most common cause of a dryer that powers on, runs the motor and blower, and still produces heat and airflow, but the drum itself sits motionless. Is W10577771 the same belt as W11568627? Yes. W10577771 was the earlier Whirlpool part number for this belt; W11568627 is the current production number for the same design. If your dryer's parts diagram shows W10577771, this part is the correct current replacement. My exact model isn't listed — will this still fit? Possibly. Whirlpool uses this belt across a range of models beyond what's confirmed in our current compatibility data. Contact our support team with your full model number and we'll verify fit before you order. Do I need to replace the idler pulley at the same time? Not necessarily — this listing is for the belt only. However, if your idler pulley is worn, noisy, or doesn't spin freely, it's worth inspecting and replacing while the dryer is already apart, since a bad idler pulley can shorten the life of a new belt. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

691366 Dryer Idler Pulley - Compatible with Whirlpool, Kenmore, Maytag, KitchenAid Product Description Keep your dryer running smoothly with the 691366 Dryer Idler Pulley. This replacement idler pulley is designed as a replacement for select Whirlpool, Kenmore, Maytag, KitchenAid, and other compatible dryers, offering a cost-effective alternative to the original. It maintains proper tension on the drive belt to ensure the dryer drum spins correctly, preventing issues like belt slippage or drum failure. This part addresses symptoms such as the dryer not tumbling, making unusual noises (e.g., squeaking or squealing), failing to start, or taking too long to dry, often caused by a worn or broken idler pulley. Note: Includes (1) idler arm and pulley assembly. Disconnect power before installation. Verify compatibility with your dryer model. Replaces part numbers: WP691366, 691366, 239477, 26000691366, 337116, 337407, 337510, 3388345, 338946, 3394332, 347034, 347226, 347277, 4319391, 688166, 691366BULK, 8207, 99989677, DE412, K35-163, W10612905, WP691366VP, PD00002256, EAP11743765, AP6010582, PS11743765. Compatibility: Compatible with select dryer models, including but not limited to: Whirlpool: WED4815EW1, WED4850BW0, WED6600VU0, 1CWGD5790VQ0, 7EWED1510YM0 Kenmore: 110.77322600, 110.77432600, 110.72832101, 110.60022010 Maytag: MED5630TQ0, 4KMED5700TQ0, 7MMEDC300BW0 KitchenAid, Amana, Inglis, Roper, Crosley, Estate, Admiral, Magic Chef: Various models (verify with model number) Verify your model number or contact our support team for assistance. Key Features: ✅ Brand and Models Compatibility: Fits select Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Inglis, Roper, Crosley, Estate, Admiral, and Magic Chef dryers. 🔧 Specifications: High-quality plastic pulley with metal idler arm. 💪 Reliable Performance: Ensures proper belt tension for smooth drum rotation and efficient drying. 🛠️ Easy Installation: Requires screwdriver, nut driver, pliers; typically installed in 20–30 minutes. 🛡️ Effective Fixes: Resolves issues like no tumbling, noisy operation, failure to start, or prolonged drying times. Product Specification Part Number: 691366 Component Type: Dryer idler pulley Material: Plastic pulley, metal idler arm Compliance: Prop 65 warning for California Installation Notes: Safety First: Disconnect the dryer from the power source before installation. Shop for high-quality appliance parts with a 30-day return policy. Keep your dryer running efficiently today! Add to cart now for a reliable fix!

Read more less

ERP DC47-00015A Dryer Thermostat Fits Specific Samsung, Whirlpool Dryer models. non-resettable dryer thermostat. Description: This Dryer Thermal Fuse is a exact replacement Part that is situated on the heating element housing for specific Samsung, Whirlpool dryer models. It meticulously measures the air temperature within the dryer drum and adjusts the heat to maintain the optimal drying temperature. In situations where your dryer doesn't start, fails to dry clothes effectively, or doesn't produce heat, a faulty thermal fuse might be the cause. Replaces Part Numbers:DC47-00015A, 2068544, 35001091, 1122484, AH2038382, DC47-00015A, EA2038382, AP4201892, PS4205212, AP4045835, PS2038382. This is an aftermarket part that can be used as a replacement for the OEM part. California Residents only WARNING: California’s Proposition 65 

Read more less

EXP652 Dryer Belt and Idler Pulley Replaces WPW10112954, 279640 The EXP652 is an aftermarket replacement drum belt and idler pulley kit for Whirlpool and Maytag electric and gas dryers, and also fits select KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models. These two components work together: the drum belt circles the drum and attaches to the motor pulley to transmit rotation, while the idler pulley rides against the belt to maintain proper tension so it doesn't slip or sag during operation. Because these two parts share the same drive path and tend to wear on a similar timeline, they're commonly sold and replaced together. Symptoms of failure include the dryer not starting, the drum not tumbling or spinning, and noise issues such as squealing or rubbing during operation. It directly replaces W10112954, WPW10112954, AP6015116, PS11748388 (drum belt), and AP3094197, PS334244, 279640, and 3388674 (idler pulley). Quick Answer The EXP652 Dryer Belt and Idler Pulley fixes Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore electric and gas dryers that won't start, won't tumble or spin, or make squealing/rubbing noise. Includes drum belt and idler pulley. Replaces W10112954, WPW10112954, AP6015116, PS11748388, AP3094197, PS334244, 279640, 3388674. These two parts wear together — replacing both at once, rather than just the one that failed, helps avoid reopening the dryer again soon after. What's In The Kit Component Replaces Function Drum Belt WPW10112954 / W10112954 Circles the drum and attaches to the motor pulley to transmit rotation and keep the drum tumbling. Idler Pulley 279640 Rides against the belt to maintain proper tension so it doesn't slip or sag. Common Problems This Kit Fixes Dryer won't start Drum won't tumble or spin Squealing or rubbing noise during operation Belt slipping or sagging, causing inconsistent tumbling Extended or inconsistent drying times Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dryer belt and idler pulley kit directly replaces the following OEM and cross-reference part numbers: Belt Replaces Part Numbers WPW10112954, W10112954, 1447719, AP6015116, AWP48873, EAP11748388, PD00003553, PS11748388 Idler Pulley Replaces Part Numbers 279640, 279640VP, 2958, 3388672, 697692, TJ279640, W10468057, AH334244, EA334244, ER279640, AWP39098, PD00002356, EAP334244, AP3094197, PS334244. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This kit is compatible with select Whirlpool electric and gas dryers, and also fits select Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore dryers built on the Whirlpool platform, including model numbers such as MED8000AG0, MED8000AW0, MGD6000XW0, MGD6000XW1, MGD6000XW2, MGD8000AG0, MGD8000AG1, MGD8000AW0, MGD8000AW1, 4KMEDC300BW0, 7MMGD0100TQ1, and MGD5500FC0. Note: Whirlpool also uses a different idler pulley, W10837240, on other dryer models — this kit specifically pairs the WPW10112954 belt with the 279640 idler pulley. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Aftermarket replacement kit — drum belt and idler pulley in one purchase Resolves "won't start," "won't tumble or spin," and "squealing/rubbing noise" symptoms Restores smooth drum rotation with proper belt tracking and tension Reduces noise and vibration from a worn belt or pulley Direct drop-in replacement matching the original belt length and pulley mounting Replaces W10112954, WPW10112954, AP6015116, PS11748388, AP3094197, PS334244, 279640, and 3388674 Compatible with Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore electric and gas dryers Built to OEM-equivalent quality standards Product Specifications Part Number EXP652 Set Contents 1x Drum Belt (replaces WPW10112954), 1x Idler Pulley (replaces 279640) Condition Aftermarket Replacement Application Whirlpool / Maytag Electric and Gas Dryers Belt Length Approx. 92-1/2" Belt Profile Flat, 5 ribs, 4 grooves Related Idler Pulley W10837240 (for other models, sold separately) Repair Difficulty Moderate — front/top panel and drum removal required Compatible Brands Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, Kenmore Installation Notes ⚠️ Unplug Dryer Before Starting — This Is A Bigger Repair Requiring Significant Disassembly Disconnect power at the outlet or shut off the circuit breaker before beginning. Wear work gloves. Remove the top and front panels of the dryer, then the drum, to access the belt and idler pulley. Remove the old drum belt from around the drum and motor pulley. Remove the old idler pulley from its mounting bracket. Install the new EXP652 idler pulley in the same position, making sure it spins freely by hand before continuing. Route and install the new drum belt correctly around the drum and motor pulley, matching the original path exactly, and re-tension it through the idler pulley. Reinstall the drum, then reassemble the front and top panels. Restore power and run a test cycle to confirm quiet, smooth operation with the drum tumbling normally and no squealing or rubbing noise. Tools needed: nut driver, Phillips screwdriver, work gloves. Frequently Asked Questions My dryer's motor runs but the drum won't turn. Is this the right kit? Yes, this is the classic symptom addressed by a worn or broken drum belt, and since the idler pulley works together with the belt to maintain proper tension, replacing both at once addresses the most common causes of this problem in one repair. Do I need to replace both parts, or just the one that failed? You can replace just the failed component if you've confirmed which one is actually bad, but these two parts share the same drive path and tend to wear out around the same time — a worn pulley can accelerate belt wear, and a worn belt puts extra strain on the pulley. Replacing both together, since you'll already have the dryer largely disassembled for access, helps avoid a second teardown soon after. Is this the same idler pulley as your other Whirlpool dryer belt kits? Not necessarily — Whirlpool uses more than one idler pulley design across its dryer lineup. This kit specifically pairs the WPW10112954 belt with the 279640 idler pulley. Other kits may pair the same belt with a different pulley, such as W10837240, used on other models. Always confirm your full model number before ordering. Is this an OEM or aftermarket part? This is an aftermarket replacement kit built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured to match the belt length, rib pattern, and pulley design of the original WPW10112954 belt and 279640 idler pulley used in compatible Whirlpool, Maytag, and related electric and gas dryers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

WD15X26078 Genuine OEM GE Dishwasher Water Inlet Valve The WD15X26078 is a Genuine OEM GE replacement dishwasher water inlet valve compatible with a wide range of GE, GE Profile, Café, Haier, Hotpoint, RCA, and Kenmore GE-built dishwashers. The water inlet valve is mounted at the base of the dishwasher behind the lower access panel, connecting the household water supply line to the dishwasher's fill circuit. When the control board calls for water during the fill phase, the valve's internal solenoid opens, allowing water to flow into the tub — and it closes the instant the call is dropped, stopping flow precisely at the correct fill level. Without a properly functioning inlet valve, the dishwasher can't fill correctly — leading to poor cleaning performance, error codes, or no wash at all. Rated 120V, 60Hz. Approximate dimensions: 3.75" H x 3.25" W x 3.00" L. Silver/multi-color metal and plastic construction with a deep-threaded, high-quality water inlet for a tight supply-line connection and a secure outlet design that keeps the internal fill hose firmly attached. As a Genuine OEM part manufactured by GE to factory specifications, the WD15X26078 directly replaces 4959029, AP6986683, PS16217027, EAP16217027, and PD00064270. Hard water sediment is a leading cause of inlet valve clogging and failure on GE dishwashers — if your old valve is restricted by mineral buildup, replacement (not cleaning) is the recommended fix, as the internal components are easily damaged during cleaning attempts. Installs in 20–30 minutes with basic hand tools. Quick Answer The WD15X26078 Genuine OEM GE Dishwasher Water Inlet Valve fixes GE, GE Profile, Café, Haier, Hotpoint, and Kenmore dishwashers that aren't filling with water, fill slowly, display the H2O error code, make strange noises or vibration during fill, won't stop filling, or leak from the valve area. 120V, 60Hz. Approx 3.75"H x 3.25"W x 3.00"L. Genuine OEM GE. Replaces 4959029, AP6986683, PS16217027, EAP16217027, PD00064270. Compatible with GDF, GDT, GDP, PDT, PDP, QDP, ZDT, DDT, and Café CDT series dishwashers. Common Problems This Part Fixes Dishwasher not filling with water at all — valve solenoid not opening Dishwasher filling slowly or not getting enough water — valve clogged with hard water sediment H2O error code displayed — insufficient water intake detected Strange noises or vibration during the fill phase — worn valve diaphragm Dishwasher won't stop filling — valve stuck open (overfill/flood risk) Water leaking from the valve area or its connections Dishes not being cleaned properly due to insufficient water fill Wash cycle interrupted or extended due to fill timeouts Valve inlet screen visibly clogged with mineral deposits Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dishwasher water inlet valve directly replaces the following OEM and cross-reference part numbers: WD15X26078, AGE846049, AP6986683, EAP16217027, PD00064270, PS16217027 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Note: some similar-looking GE valves (such as WD15X24213 or WD15X26140) are different parts — verify your original valve's part number or your dishwasher model number before ordering. Compatibility This water inlet valve is compatible with select dishwashers from the following brands: GE dishwashers — GDF series (GDF510PGM4BB/WW, GDF510PSM4SS/5SS, GDF511PSM5SS, GDF511PGM5WW, GDF530PGM4BB/CC/WW/5WW, GDF530PSM4SS/5SS, GDF530PMM4ES, GDF565SSN3SS, GDF630PFM4DS/5DS, GDF630PGM4BB/WW/5BB, GDF630PMM4ES/5ES, GDF630PSM4SS, GDF640HFM4DS, GDF640HGM4WW/5BB, GDF640HMM4ES, GDF645SGN2BB/WW/3BB/3WW, GDF645SMN2ES/3ES, GDF645SSN2SS/3SS and related) GE dishwashers — GDT series (GDT530PGP5BB, GDT530PSP5SS, GDT535PSMASS, GDT535PSM5SS, GDT565SSN2SS, GDT605PSM5SS, GDT630PFM4DS, GDT630PMM4ES/5ES, GDT630PYM4FS, GDT635HMM4ES, GDT635HSM4SS/5SS, GDT645SGN2BB/WW/3WW, GDT645SMN3ES, GDT645SSN2SS, GDT645SYN2FS, GDT665SBN2TS/3TS, GDT665SFN3DS, GDT665SGN2WW/3WW, GDT665SMN2ES, GDT665SSN3SS and related) GE dishwashers — GDP series (GDP615HFM4DS, GDP645SYN3FS/4FS/8FS, GDP665SYN2FS/3FS/4FS/8F7S and related) GE Profile dishwashers — PDT series (PDT715SBN2TS/3TS, PDT715SFN3DS, PDT715SMN2ES/3ES, PDT715SYN3FS, PDT775SYN2FS/3FS, PDT785SBN2TS, PDT785SYN2FS/3FS/5FS and related) GE Profile dishwashers — PDP series (PDP715SBN3TS, PDP715SYN3FS and related) GE dishwashers — QDP series (QDP555SBN4TS, QDP555SYN4FS and related) GE Monogram dishwashers — ZDT series (ZDT925SIN2II/3II/5II, ZDT925SPN2SS/3SS, ZDT925SSN2SS/3SS/5SS, ZDT985SIN3II, ZDT985SPN5SS, ZDT985SSN5SS and related) GE dishwashers — DDT series (DDT700SBN2TS/3TS, DDT700SFN2DS/3DS, DDT700SGN2BB/WW, DDT700SMN2ES and related) Café dishwashers — CDT series (CDT800P2N2S1-N5S1, CDT805M5N2S5-N4S5, CDT805P2N2S1-N5S1, CDT845M5N2S5-N5S5, CDT845P2N2S1-N5S1, CDT845P3N2D1-N5D1, CDT845P4N2W2-N5W2, CDT855M5N2S5/N3S5/N5S5, CDT855P2N2S1/N3S1/N5S1, CDT875M5N2S5-N7S5, CDT875P2N2S1-N5S1, CDT875P3N5D1 and related) Haier dishwashers (select models using the GE-platform valve) Hotpoint and RCA dishwashers (select GE-built models) Kenmore / Sears dishwashers (select GE-built models) Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Genuine OEM part manufactured by GE to factory specifications — guaranteed fit and performance Controls the flow of water into the dishwasher during fill cycles — precise fill for optimal cleaning performance Solenoid-actuated — opens when the control board calls for water and closes the moment the call is dropped Rated 120V, 60Hz — correct electrical specifications for compatible GE-platform dishwashers Approximate dimensions: 3.75" H x 3.25" W x 3.00" L Deep-threaded water inlet for a tight, leak-free supply line connection Secure outlet design keeps the internal fill hose firmly attached Resolves H2O error codes, no-fill, slow-fill, overfill, and fill-noise symptoms Replaces 4959029, AP6986683, PS16217027, EAP16217027, and PD00064270 Compatible with GE GDF/GDT/GDP series, GE Profile PDT/PDP series, QDP series, Monogram ZDT series, DDT series, Café CDT series, plus Haier, Hotpoint, RCA, and Kenmore GE-built dishwashers DIY repair — installs in 20–30 minutes with basic hand tools Product Specifications Part Number WD15X26078 Part Type Dishwasher Water Inlet Valve Assembly Condition Genuine OEM Application Dishwashers (GE platform) Voltage 120V AC Frequency 60 Hz Dimensions Approximately 3.75" H x 3.25" W x 3.00" L Color Silver / Multiple Colors Material Metal / Plastic Error Codes Resolved H2O (insufficient water intake) Compatible Brands GE, GE Profile, Café, Monogram, Haier, Hotpoint, RCA, Kenmore Installation Notes ⚠️ Unplug Dishwasher and Shut Off Water Supply Before Starting — Wear Work Gloves Disconnect power at the breaker and shut off the household water supply at the shutoff valve under the sink before beginning. Wear work gloves to protect your hands. Have towels and a shallow dish ready — residual water remains in the supply line and hoses and will spill when disconnected. Remove the lower access panel (baffle) at the front bottom of the dishwasher — typically 2–4 screws. Locate the water inlet valve where the household supply line enters the dishwasher. Photograph the hose and wire connections before disconnecting anything. Disconnect the household water supply line from the valve inlet (use pliers for the larger ingress connection — place the dish underneath to catch leftover water). Disconnect the internal fill hose from the valve outlet (needle-nose pliers help with the smaller egress hose clamp). Unplug the electrical connector that snaps onto the valve solenoid. Remove the mounting screws holding the valve bracket to the frame and lift the old valve out. Install the new WD15X26078 valve in the same position, secure the mounting screws, reconnect the internal fill hose with its clamp, and snap the electrical connector back on. Reconnect the household water supply line to the valve inlet — align the threads carefully and tighten snugly without over-torquing. Turn the water supply back on and use a flashlight to inspect all connections for leaks BEFORE reinstalling the access panel. Restore power and run a test cycle to confirm proper filling with no leaks. Tools needed: Phillips screwdriver, pliers, needle-nose pliers, shallow dish, towels, flashlight, work gloves. Frequently Asked Questions What does the H2O error code mean on my GE dishwasher? The H2O error code on GE dishwashers indicates the control board is not detecting sufficient water intake during the fill phase. Common causes are: a failed or clogged water inlet valve (the most frequent culprit), the household water supply shutoff valve partially closed, a kinked supply line, or low household water pressure. First verify the supply valve under the sink is fully open and the line isn't kinked. If the supply checks out, the WD15X26078 inlet valve is the standard fix — hard water sediment gradually clogs the valve's internal screen and passages, restricting flow until the dishwasher can't fill within its expected time window. Can I clean the old valve instead of replacing it? It's not recommended. While the inlet screen on some valves can be carefully brushed clean, the internal passages and solenoid diaphragm of a sediment-clogged valve are easily damaged during cleaning attempts — a common outcome is a valve that leaks or sticks open after being "cleaned," which risks flooding. Real-world experience (including customer stories with this exact part) shows that attempting to clean a hard-water-clogged valve often breaks it. Given the moderate cost of the OEM replacement versus the flood risk of a compromised valve, replacement is the reliable repair. If your area has hard water, consider this a maintenance item that may need periodic replacement. My dishwasher won't stop filling — is that also this valve? Yes — a valve stuck in the open position is the other failure mode. When sediment or a worn diaphragm prevents the valve from sealing fully closed, water continues to flow into the tub even when the control board has cut power to the solenoid. This can lead to overfilling and potentially flooding through the door or float overflow. If your dishwasher keeps filling past its normal level, or you find water accumulating in the tub between cycles, shut off the water supply at the sink immediately and replace the valve before running the dishwasher again. How do I know this is the right valve for my GE dishwasher? Check your dishwasher's model number (on a label along the door frame or tub edge) against the compatibility list above — the WD15X26078 covers a broad range of GE GDF, GDT, GDP, Profile PDT/PDP, QDP, Monogram ZDT, DDT, and Café CDT series dishwashers. Be aware that some similar-looking GE valves (such as WD15X24213 or WD15X26140) are different parts used on other model groups — they are not interchangeable with the WD15X26078. If your model isn't in the list or your original valve shows a different part number, contact our support team with your model number and we'll verify the correct valve before you order. Is this a Genuine OEM or aftermarket part? This is a Genuine OEM part manufactured by GE to factory specifications. It is the exact same water inlet valve installed in compatible GE, GE Profile, Café, Monogram, Haier, Hotpoint, RCA, and Kenmore GE-built dishwashers from the factory — guaranteed fit, materials, and performance. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO 6931EL3001E Dryer Thermostat – Compatible with LG and Kenmore Dryers Product Description Maintain proper dryer safety and temperature control with the 6931EL3001E Dryer Thermostat. This replacement part monitors and regulates dryer temperature to prevent overheating and ensure efficient drying cycles. A faulty thermostat may cause your dryer to stop heating, overheat, or shut off unexpectedly. Replacing it restores reliable performance and helps extend the life of your dryer. Replaces Part Numbers 6931EL3001E, 1268363, 6931EL3001B, 6931EL3001C, AH3530481, EA3530481, PD00023869, EAP3530481, AP4440977, PS3530481, L125-31C, 503475. Compatibility This dryer thermostat is compatible with select LG and Kenmore dryer models. Example compatible models include (but are not limited to): LG DLE2516W, DLE7177WM, and Kenmore 796.80272900. Always verify your dryer’s model number before ordering. Contact our support team if you’re unsure. ✅ Key Features 🔄 Broad Compatibility – Fits select LG and Kenmore dryers 🔒 Reliable Safety – Prevents overheating by regulating dryer temperature 💰 Cost-Effective Replacement – OEM-equivalent performance at a lower price 🛠️ DIY-Friendly – Quick installation with basic tools 🛡️ Fixes Common Issues – Restores heating, prevents overheating, and fixes dryer shutdown problems 📐 Product Specification Part Number: XP6931EL3001E Component Type: Dryer Thermostat Material: High-heat resistant metal and thermal components Mounting: Direct replacement, mounts on heating element housing Operating Conditions: Designed for residential dryers Compliance: OEM-equivalent performance and safety standards 🛠️ Installation Notes Tools Needed: Phillips screwdriver, flathead screwdriver, needle-nose pliers ⚠️ Safety First: Always disconnect power before starting repairs to avoid electrical shock. Steps: Unplug dryer and remove back access panel. Locate thermostat on heating element housing. Disconnect wire terminals from the old thermostat. Remove screws holding it in place and replace with the new thermostat. Reconnect wires, secure the component, and reinstall the access panel. Restore power and test dryer operation. ⏱️ Time Required: 15–20 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders 🛠️ Trusted Appliance Parts Supplier 🔄 30-Day Return Policy Restore your dryer’s safe operation today — Add to Cart Now for fast, budget-friendly repair!

Read more less

12500039 Range Genuine OEM Radiant Surface Element Radiant heating element. 6" smoothtop range element with overheat limit switch For glass cooktops and freestanding ranges. Replaces Part Numbers:W10823704, 12500039, 74002653, WP74002653, 04100415, 0E00602299, 3189893, 3196428, 4454863, 71001423, 74001011, 74002651, 74005476, 7406P034-60, 7406P053-60, 7406P058-60, 7406P074-60, 8185657, 8203553, AP6030932, PS11764912, W10823736, Y04100415, Y0E00602299.  Description: This Radiant Surface Element is a Genuine OEM part for specific Maytag, Whirlpool ranges models. It provides the heat necessary for cooking by radiating heat through the cooktop surface. This element is designed to fit under the glass surface of your range, delivering consistent and even heat for various cooking tasks.  Causes of a bad radiant surface element can include wear and tear from regular use, overheating, or damage due to impact. Electrical issues can also affect the performance of the element, leading to inconsistent heating.   California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

Genuine Frigidaire OEM Frigidaire 5304533220 Washer Water Fill Hose Assembly Genuine OEM internal valve-to-tub fill hose for select Frigidaire-built laundry centers and washer/dryer combination units. Product Overview The Frigidaire 5304533220 Washer Water Fill Hose Assembly is a Genuine OEM internal fill hose used to route incoming water from the washer water inlet valve to the wash tub on compatible laundry-center models. This is the valve-to-tub hose inside the appliance. It is not the external hot/cold household water-supply hose that connects the appliance to the wall faucets. Quick Answer 5304533220 is the Genuine Frigidaire OEM valve-to-tub washer fill hose. It replaces earlier Frigidaire numbers 5304508358 and 809191901 and is used on select Frigidaire, Kenmore, Crosley, and other Electrolux-manufactured laundry centers. Common Problems This Part May Fix Water leaking inside the washer cabinet during fill Cracked, split, hardened, or deteriorated fill hose Leak between the inlet-valve outlet and wash tub Loose or damaged internal water-fill connection Water dripping from the valve-to-tub hose during operation Replaces and Cross-References 5304533220, 5304508358, 809191901, AFR20016, AP7194866, EAP11775692, PD00076846, PS16745853 Cross-reference numbers are provided for identification. Always verify the full appliance model number before ordering. Compatibility Confirmed applications include select Frigidaire-built laundry centers and washer/dryer combinations such as: FLCE7523AW0 FLCE7523AW1 FLCE7522AW1 FLCE7522AW4 FFLE3900UW0 FFLE3900UW1 FFLG3900UW0 FFLE3911QW1 CFLE3900UW0 41761712511 41761732810 41771732810 Important: This is only a partial compatibility list. Confirm the complete model number from the appliance rating label before purchase. Key Features Genuine Frigidaire OEM replacement part Internal valve-to-tub fill hose Routes fill water from the inlet valve to the washer tub Direct replacement for 5304508358 and 809191901 Factory-style fit for compatible laundry centers Used on select Frigidaire, Kenmore, and related Electrolux-built models Product Specifications Manufacturer Part Number 5304533220 Brand Frigidaire Part Type Washer Internal Water Fill Hose Hose Location Water Inlet Valve to Wash Tub OEM Status Genuine OEM Appliance Type Laundry Center / Washer-Dryer Combo Condition New External Supply Hose? No — this is an internal appliance hose Installation Notes Disconnect electrical power to the appliance before service. Shut off both household water-supply valves. Access the washer inlet-valve and tub-fill connection according to the model-specific service procedure. Place towels or a shallow pan below the hose connections to catch residual water. Release the clamps and remove the old hose without damaging the valve outlet or tub fitting. Install the new hose fully onto both fittings and reinstall the clamps in their original positions. Restore water and inspect carefully for leaks before returning the appliance to service. Diagnostic tip: If water is leaking during fill, inspect the hose, clamps, inlet valve, and tub connection before replacing parts. A leak from the external household supply hose requires a different part. Frequently Asked Questions Is 5304533220 a Genuine OEM part? Yes. It is a Genuine Frigidaire OEM fill hose. Does 5304533220 replace 5304508358? Yes. 5304533220 supersedes 5304508358 and 809191901. Is this the hose that connects the washer to the wall faucet? No. This is an internal valve-to-tub fill hose located inside the laundry center. Can this part correct a washer leak? Yes, if the leak is caused by a cracked or damaged valve-to-tub fill hose or its connection. Inspect all nearby fittings and clamps before ordering. Shop With Confidence Verify your complete laundry-center model number before ordering. This listing is for the Genuine Frigidaire OEM internal valve-to-tub fill hose. Genuine Frigidaire OEMValve-to-Tub Fill HoseCompatibility SupportFast U.S. Shipping

Read more less

8270020CM Dishwasher Door Spring Door balance spring - 7.75" overall length. Fits Whirlpool dishwashers. Replaces Part Numbers:WP8270020, 8270020, AP6012319, PS11745526.   This is an aftermarket part that can be used as a replacement for the OEM part.   California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

XPARTCO 137292700 Dryer Drum Belt The XPARTCO 137292700 is an aftermarket replacement multi-rib drum belt for Frigidaire stacked laundry center (combination washer/dryer) units, and also fits select Crosley, Electrolux, Gibson, Kelvinator, Kenmore, Tappan, and White Westinghouse combo models. This belt attaches to the motor pulley and spins the drum as the motor rotates, keeping clothes tumbling evenly throughout the drying cycle. Measures approximately 89-1/2" long and 1/4" wide, with multiple ribs. Over time, this belt naturally dries out, cracks, or breaks from regular use. If your dryer is running but the drum won't turn, there's a good chance the belt has broken. Symptoms of a failing belt include the drum not turning, loud banging noises, or the dryer failing to tumble clothes. It directly replaces 137292700, 134163500, 134503900, 5303283287, 4PH 2273, 4PH2273, AFR14366, AH3408299, AP4565702, EA3408299, EAP3408299, PD00000115, PS3408299. Quick Answer The XPARTCO 137292700 Dryer Drum Belt fixes Frigidaire, Crosley, Electrolux, Gibson, Kelvinator, Kenmore, Tappan, and White Westinghouse stacked laundry center units where the drum won't turn, you hear loud banging noises, or the dryer won't tumble clothes. Approximately 89-1/2" long, 1/4" wide, multiple ribs. Replaces 137292700, 134163500, 134503900, 5303283287, 4PH 2273, 4PH2273, AFR14366, AH3408299, AP4565702, EA3408299, EAP3408299, PD00000115, PS3408299. This is a laundry center (stacked combo) belt, distinct from standalone dryer belts — verify your full model number before ordering. Common Problems This Part Fixes Drum won't turn even though the motor is running Loud banging noises during operation Dryer failing to tumble clothes Belt visibly cracked, dried out, or broken Drum stopping mid-cycle Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dryer drum belt directly replaces the following OEM and cross-reference part numbers: 137292700, 134163500, 134503900, 5303283287, 4PH 2273, 4PH2273, AFR14366, AH3408299, AP4565702, EA3408299, EAP3408299, PD00000115, PS3408299 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This drum belt is compatible with select Frigidaire stacked laundry center units, and also fits select Crosley, Electrolux, Gibson, Kelvinator, Kenmore, Tappan, and White Westinghouse combo units built on the same platform, including model numbers such as WLXG42REW0, FLSE72GCTC, FLSG72GCT1, FLSG72GCT6, LCE852LL1, FLXG52RBS2, FLXG52RBS8, FLXE52RBS9, CLCG900FW0, CLCG900FW1, CLCG900FW2, CLCG900FW3, CLCE900FW0, CLCE900FW1, CLCE900FW2, CLCG500FW0, CLCG500FW1, CLCE600RW0, CLCE500MW1, CLCE500FW2, and CLCE500FW4. Note: This is a laundry center (stacked washer/dryer combo) belt, distinct from standalone Frigidaire dryer belts. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Aftermarket replacement multi-rib drum belt — built to OEM-equivalent specifications Attaches to the motor pulley to spin the drum for laundry center (combo) units Resolves "drum won't turn," "loud banging noises," and "won't tumble" symptoms Approximately 89-1/2" long, 1/4" wide, multiple ribs Direct drop-in replacement matching the original length and profile Replaces 137292700, 134163500, 134503900, 5303283287, 4PH 2273, 4PH2273, AFR14366, AH3408299, AP4565702, EA3408299, EAP3408299, PD00000115, PS3408299 Compatible with Frigidaire, Crosley, Electrolux, Gibson, Kelvinator, Kenmore, Tappan, and White Westinghouse laundry center units Aftermarket replacement built to OEM-equivalent quality standards Product Specifications Part Number XP137292700 OEM Part Number 137292700 Part Type Laundry Center Multi-Rib Drum Belt Condition Aftermarket Replacement Compatible Brand Frigidaire Application Stacked Washer/Dryer Laundry Centers Length Approx. 89-1/2" Width 1/4" Ribs Multiple Function Transmits motor rotation to spin the drum Repair Difficulty Moderate — laundry center disassembly required Quantity 1 drum belt Compatible Brands Frigidaire, Crosley, Electrolux, Gibson, Kelvinator, Kenmore, Tappan, White Westinghouse Installation Notes ⚠️ Unplug The Laundry Center Before Starting Disconnect power to the laundry center unit at the outlet before beginning. Wear work gloves. This repair is best approached from the top down: remove the top of the unit first, which gives more room to get the dryer tub out. Remove the two screws from the vented plate on the back of the machine to access and undo the old belt. Since this is a stackable washer/dryer combo, also remove the white plate on the front between the washer and dryer sections for full access. Locate the old belt connecting the motor pulley to the drum and remove it. Fit the new 137292700 belt around the drum and motor pulley in the same path as the old one, making sure it seats correctly and is properly tensioned. Reassemble the front plate, vented back plate, and top of the unit. Restore power and run a test cycle to confirm the drum tumbles smoothly with no banging or unusual noise. Tools needed: putty knife, screwdriver set, work gloves. Frequently Asked Questions The motor is running but the drum won't turn. Is this the belt I need? Yes, this is the classic and most reliable sign of a broken drum belt. If you can hear the motor running normally but the drum itself stays still, the belt has likely dried out and broken, no longer connecting the motor's rotation to the drum. Is this the same as a standalone Frigidaire dryer belt? No, this belt is specifically sized and profiled for Frigidaire-style stacked laundry center units, where the washer and dryer are combined into one appliance. It's a different part from standalone Frigidaire dryer belts used on separate dryers. Confirm your unit type and model number before ordering. Is this a difficult repair? It's a moderate repair since it involves removing the top of the laundry center unit, the vented back plate, and the front plate between the washer and dryer sections to get full access to the belt. One customer described working from the top down as the easiest approach, since it gives more room to remove the dryer tub. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Frigidaire OEM part, but is manufactured to match the length, width, and rib pattern of the original 137292700 multi-rib drum belt used in compatible Frigidaire, Crosley, Electrolux, Gibson, Kelvinator, Kenmore, Tappan, and White Westinghouse laundry center units. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

Genuine Whirlpool WPW10131172 Dryer Drive Belt - Compatible with Admiral, Amana, Maytag, Whirlpool Product Description Ensure efficient drying with the Genuine Whirlpool WPW10131172 Dryer Drive Belt. This OEM drive belt is designed for select Admiral, Amana, Crosley, Inglis, Maytag, and Whirlpool dryers, driving the drum to ensure proper rotation and consistent performance. Made of durable rubber, it delivers reliable tension and flexibility, addressing issues like the drum not spinning, excessive noise, or failure to start. Note: Includes one drive belt. Disconnect power and gas (if applicable) before installation. Inspect drum rollers and idler pulley for wear during replacement. Replaces part numbers: WPW10131172, W10131172, 1449763, PD00003839, EAP11748749, AP6015470, PS11748749. Verify your model number or contact our support team for assistance. Key Features: ✅ Brand and Models Compatibility: Fits select Admiral, Amana, Crosley, Inglis, Maytag, and Whirlpool dryers. 🔄 Specifications: OEM rubber drive belt, 4 ribs, 3 grooves. 💪 Reliable Performance: Authentic Whirlpool part ensures long-lasting durability and proper tension. 🛠️ Easy Installation: Requires screwdriver, socket wrench, and work gloves; typically installed in 20–30 minutes. 🛡️ Effective Fixes: Resolves drum not spinning, excessive noise, or failure to start issues. Product Specification Part Number: Genuine Whirlpool WPW10131172 Component Type: Dryer drive belt Material: Rubber Mounting: Tension-mounted around drum and motor pulley Operating Conditions: Suitable for household and commercial dryer environments Compliance: Prop 65 warning for California Installation Notes: Safety First: Disconnect the dryer from the power source and gas supply (if applicable) before installation. Shop for high-quality Genuine appliance parts with a 30-day return policy. Keep your dryer running smoothly today! Add to cart now for a reliable fix!

Read more less

XPARTCO LA1053 Dryer Thermostat Kit – Replaces LA-1053 – Compatible with Whirlpool, Maytag, Admiral, and Amana Dryers Product Description Restore proper dryer temperature control with the XPARTCO LA1053 Dryer Thermostat Kit. This Dryer Thermostat Kit is a replacement part for specific Maytag, Whirlpool dryer models. This kit includes a high-limit thermostat and a thermal fuse, both of which are crucial for regulating the dryer’s temperature. The high-limit thermostat prevents the dryer from overheating, while the thermal fuse will cut off power if a critical temperature is exceeded, ensuring safety. The kit includes a high-limit thermostat (53-0771) and two thermal fuses. 53-1096 (blue dot for Gas) 53-1182 (Red dot for Electric) Replaces Part Numbers LA-1053, 3344, 53-0143, 53-0170, 53-0261, 53-1133, 53-1526, AH2162282, EA2162282, ERLA1053, ET403, ET405, K35-601, LA-1053VP, LA1053, SET405, TJ90SET405, 531526, 531182, 531133, 530261, LA1053, 530143, WP53-1182, 53-1182, 53-0143, 53-1096 , L248-80F, PD00002446, EAP2162282, AP4242472, PS2162282, WP53-0771, 53-0771, 1422, 53-0306, 53-1037, 53-1459, ER53-0771, SET176, TJSET176, AP6009638, PS11742806, WP53-1096, 53-1096, 4434853, AP6009640, PS11742808.  Compatibility This replacement thermostat kit fits select Whirlpool, Maytag, Admiral, and Amana dryers. Example compatible models include (but are not limited to): Maytag DE303, Whirlpool LDE8824ACE, and Amana LEA30AW. Always verify your dryer’s model number before ordering. Contact our support team if you’re unsure. ✅ Key Features 🔄 Compatibility – Compatible with Whirlpool, Maytag, Admiral, and Amana dryers 🔥 Complete Kit – Includes cycling thermostat, high-limit thermostat, and thermal fuse. Dryer thermal fuse and high limit thermostat kit for both gas and electric models. If the dryer does not heat then the thermal fuse may have blown and will need to be replaced.  💰 Cost-Effective Repair – Replaces multiple components in one package 🛠️ Easy to Install – Direct-fit parts require only basic tools 🛡️ Fixes Common Issues – Resolves dryers not heating, overheating, or shutting off early 📐 Product Specification Part Number: LA1053 Component Type: Dryer Thermostat and Thermal Fuse Kit Material: Heat-resistant metal with high-quality electrical connectors Mounting: Direct-fit replacement on heater housing and blower housing Operating Conditions: Designed for residential electric dryers Compliance: Built to OEM-equivalent quality standards (not OEM) 🛠️ Installation Notes Tools Needed: Phillips screwdriver, nut driver ⚠️ Safety First: Always unplug the dryer before performing any repairs to prevent electrical shock. Steps: Unplug the dryer and remove the rear access panel. Locate the thermostat and thermal fuse on the heater housing. Remove screws securing the old components and disconnect wires. Install the new thermostats and fuse from the XPARTCO LA1053 kit. Reconnect wiring, reinstall the back panel, and restore power. Run a test cycle to confirm proper heating and temperature control. ⏱️ Time Required: 20–25 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders 🛠️ Trusted Appliance Parts Supplier 🔄 30-Day Return Policy Get your dryer running safely and efficiently again — Add to Cart Now for a reliable, budget-friendly repair kit!

Read more less