Search results for "refrigerator switch"

ERP 134715900 Dryer Drum Roller with Axle Replaces Part Numbers: 134715900, 5304523155, AP6979841, 7134715900, AP6977189, PS12746506. Description: The Roller Assembly is a replacement part specific to Electrolux, Frigidaire clothes dryer models. It contains multiple smooth-rolling cylinders that guide the dryer drum assembly as it turns.    This is an aftermarket part that can be used as a replacement for the OEM part.

Read more less

XPARTCO 8318314 Dryer Thermal Cutoff Fuse (352°F) The XPARTCO 8318314 is an aftermarket replacement 352°F thermal cutoff fuse compatible with a wide range of Whirlpool, Maytag, KitchenAid, Kenmore, Amana, Crosley, Roper, Inglis, and Estate dryers. The thermal cutoff fuse is a critical safety device mounted near the heating element housing — it acts as a backup safety in case the high-limit thermostat fails to open. When the air temperature inside the heating element area reaches 352°F, the fuse permanently opens and cuts power to the heater circuit, preventing the dryer from continuing to overheat and creating a fire risk. This is a one-time fuse — once it has tripped, it cannot be reset and must be replaced. White and gray metal/ceramic construction. Dimensions: 1-1/4"L x 1-1/4"W x 2-3/16"H, with approximately 1-5/8" between mounting holes (center to center). It directly replaces 8318314. Important: when the thermal cutoff blows, the high-limit thermostat (8557403 — sold separately) is often also stressed and should be tested or replaced at the same time. Installs in 15–20 minutes with basic hand tools. Quick Answer The XPARTCO 8318314 Dryer Thermal Cutoff Fuse (352°F) fixes Whirlpool, Maytag, KitchenAid, Kenmore, Amana, Crosley, Roper, Inglis, and Estate dryers that suddenly stopped heating after an overheat event. One-time fuse — 352°F open, must be replaced once blown. 1-1/4"L x 1-1/4"W x 2-3/16"H, ~1-5/8" between mounting holes. Metal/ceramic. Often replaced alongside the high-limit thermostat (8557403, sold separately). Common Problems This Part Fixes Dryer suddenly stopped heating with no warning — thermal cutoff has blown after an overheat event Dryer runs and tumbles normally but produces no heat No-heat fault following a partially blocked exhaust vent or restricted airflow event Multimeter continuity test shows the cutoff has an open circuit (no continuity) Visible damage or discoloration around the thermal cutoff housing from a prior overheat event Repeated no-heat problems where the thermal cutoff has tripped more than once Replaces Part Numbers This thermal cutoff fuse directly replaces the following OEM and cross-reference part numbers: 8318314 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This 352°F thermal cutoff fuse is compatible with select dryers from the following brands: Whirlpool dryers (Elite, Cabrio, Duet, and WED series — select models including WED9200, WED7300, WED7400, WED7600 and related) Maytag dryers (Maxima and MED series — select models including MED3500, MED6000XW, MEDE900VW and related) KitchenAid dryers (select models) Kenmore / Sears dryers — Elite 110-series and related Whirlpool-built models Amana dryers — NED and YNED series (select models including NED7500VW1 and related) Crosley dryers (CED series and related models) Roper dryers (select models) Inglis dryers (select models) Estate dryers (select models) Important — Check Vent Before Restarting: A blown thermal cutoff is almost always the result of restricted dryer airflow. Before replacing this fuse and restoring service, thoroughly clean the dryer's exhaust vent line all the way to the exterior wall outlet, the lint screen, and any internal lint buildup. Installing a new thermal cutoff without fixing the underlying airflow problem will cause the new fuse to blow within a short time, repeating the failure. Key Features 352°F one-time safety fuse — permanently opens to cut power to the heater circuit if the dryer overheats Backup safety device — protects against overheating in case the high-limit thermostat fails to open Cannot be reset — must be replaced once blown Dimensions: 1-1/4"L x 1-1/4"W x 2-3/16"H; approximately 1-5/8" between mounting holes (center to center) Metal and ceramic construction in white/gray Often replaced together with the high-limit thermostat (8557403, sold separately) as a paired safety repair Compatible with Whirlpool, Maytag, KitchenAid, Kenmore, Amana, Crosley, Roper, Inglis, and Estate dryers Aftermarket replacement built to OEM-equivalent quality standards Quick DIY repair — installs in 15–20 minutes with basic hand tools Product Specifications Part Number 8318314 Part Type Dryer Thermal Cutoff Fuse (Safety Fuse) Condition Aftermarket Replacement Application Electric and Gas Dryers (Whirlpool platform) Trip Temperature 352°F Fuse Type One-Time (must be replaced once blown — cannot be reset) Dimensions 1-1/4"L x 1-1/4"W x 2-3/16"H Mounting Hole Spacing Approx. 1-5/8" center to center Color White / Gray Material Metal / Ceramic Often Replaced With High-Limit Thermostat (8557403, sold separately) Compatible Brands Whirlpool, Maytag, KitchenAid, Kenmore, Amana, Crosley, Roper, Inglis, Estate Installation Notes ⚠️ Unplug Dryer Before Starting — Clean Vent System First Disconnect power before beginning. Wear work gloves to protect your hands. Before installing the new thermal cutoff, thoroughly clean the dryer's vent line — from the lint screen through the duct to the exterior wall outlet, plus any internal lint buildup around the heater housing. A blown thermal cutoff is virtually always caused by restricted airflow; if you don't fix the underlying cause, the new fuse will trip again soon. Access the thermal cutoff by removing the rear (or front, depending on model) access panel of the dryer to expose the heating element housing. The 8318314 thermal cutoff is mounted on or near the heater housing. Photograph the wire connections before disconnecting. Disconnect the wires from the old cutoff and remove the mounting screw(s). Install the new 8318314 cutoff in the same position and reconnect the wires. While the panel is open, this is also the ideal time to test or replace the high-limit thermostat (8557403) — overheat events that blow this fuse often damage that component too. Reassemble the panel, restore power, and run a test heat cycle to confirm normal heat operation. Tools needed: Phillips screwdriver, 1/4" nut driver, multimeter, work gloves. Frequently Asked Questions What's the difference between a thermal cutoff, a thermal fuse, and a high-limit thermostat? All three are safety components in a dryer's heating circuit but they serve different roles. The high-limit thermostat (such as 8557403 or 3391914) is a resettable safety switch — it opens when the air gets too hot, then closes again automatically once it cools. The thermal cutoff (8318314, 352°F) is a one-time fuse on the heating element circuit — it blows permanently if the temperature exceeds 352°F, meaning the high-limit thermostat failed to do its job. The thermal fuse (often 3392519) is a separate one-time fuse mounted on the exhaust duct — it blows if exhaust airflow temperature exceeds its rating. Each protects against a different failure mode and is replaced individually when it blows. Why did my thermal cutoff blow in the first place? A blown thermal cutoff is almost always the result of restricted airflow through the dryer. The most common causes are: a clogged or kinked exhaust vent line, a clogged lint screen, lint buildup inside the dryer cabinet near the heater housing, or a failed blower wheel/motor that's not moving enough air. Less commonly, a failed high-limit thermostat (stuck closed) can let the dryer overheat until the thermal cutoff blows as a last-resort safety. Before replacing this part, identify and fix the underlying airflow issue — otherwise the new fuse will blow within a short time. Should I replace the high-limit thermostat at the same time? Yes, it's highly recommended. The thermal cutoff is the second line of defense against overheating — for it to trip, the high-limit thermostat ahead of it likely failed to open at its normal cycling temperature, was stressed by the overheat event, or was already weakened. Replacing the high-limit thermostat (8557403 on many compatible Whirlpool-platform dryers) at the same time is standard practice and ensures both safety components work correctly together. The 279973 kit even bundles a thermal cutoff with a high-limit thermostat for this reason. Can the thermal cutoff be reset like a circuit breaker? No — the 8318314 is a one-time thermal fuse. Once it opens at 352°F, it permanently breaks the electrical circuit and cannot be reset. Some appliance components (like a high-limit thermostat) can reset automatically as they cool, but a thermal cutoff fuse is a single-use safety device by design. If your dryer suddenly stopped heating and a continuity test on this fuse shows an open circuit, it must be replaced. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured from metal and ceramic with the same 352°F trip temperature, dimensions (1-1/4"L x 1-1/4"W x 2-3/16"H), and mounting hole spacing (1-5/8" center to center) as the original 8318314 thermal cutoff fuse. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

WD26X23258 Dishwasher Genuine Circulation Pump Genuine dishwasher circulation pump designed to move water through the spray arms and restore proper wash performance. ✓ Genuine Part ✓ Replaces WD26X23258 ✓ Compatibility Support Product Description This Pump is a Genuine component for specific GE dishwasher models. It refers to the water pump component that circulates water throughout the dishwasher during cycles. Common cause of a faulty pump can include normal wear over many uses. The continuous motor operation puts strain on internal seals and impellers. Mineral deposits from hard water can also clog pump parts over time. Replacing a faulty circulation pump can help restore proper water movement and improve dishwasher cleaning performance. Quick Answer If your dishwasher is not washing properly, has weak spray pressure, or makes unusual pump noise, the WD26X23258 circulation pump may need replacement. ⚠️ Always verify your dishwasher’s model number before ordering. Contact our support team if you’re unsure. Common Problems This Part Fixes Dishwasher not cleaning dishes properly Weak spray arm water pressure Circulation pump noise Water not circulating during wash cycle Poor wash performance Replaces part Number WD26X23258, 4466766, WD26X22285, WD26X22518, WD26X22826, AGE25293, AP6039424, EAP11772000, PD00041691, PS11772000. Compatibility This part fits select GE, Hotpoint, Kenmore, and compatible dishwasher models using part number WD26X23258. Always verify your dishwasher’s model number before ordering. Contact our support team if you’re unsure. Key Features Genuine dishwasher circulation pump Helps restore proper water circulation Supports spray arm water pressure Designed for compatible dishwasher models Reliable replacement component Product Specifications Brand GE Part Type Dishwasher Circulation Pump Primary Part Number WD26X23258 Compatible Appliance Type Dishwasher Condition Genuine New Installation Disconnect power and water supply before installation. Inspect hoses and seals for leaks after installation. Troubleshooting Guide ⚠️ Disconnect power and water supply before servicing the dishwasher. Check spray arms for blockage before replacing the pump. Inspect pump area for leaks or unusual noise. Verify wiring connections are secure. Replace the circulation pump if water circulation problems continue. When Should You Replace This Part? Replace the dishwasher circulation pump if the dishwasher has poor cleaning performance, weak spray pressure, unusual pump noise, or water is not circulating during the wash cycle. Shop With Confidence We are a U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock parts for major appliance brands and ship quickly from our U.S. warehouse. ✓ Fast Shipping ✓ Genuine Parts ✓ Compatibility Support ✓ Secure Checkout  

Read more less

XPARTCO WH01X24378 Washer / Dryer Cycle Selector Knob The XPARTCO WH01X24378 is an aftermarket replacement cycle selector knob (options knob) compatible with a wide range of GE, Hotpoint, RCA, Haier, Monogram, and Café washers and dryers. The selector knob is one of the primary user controls on the appliance's control panel — it's what you grip and turn to choose the wash or dry options and settings for each load. On many GE-platform washers and dryers, this smaller selector knob works alongside a larger main timer/cycle knob to give you fine-grained control over the specific options within your selected cycle. Over time, selector knobs wear out from repeated twisting motions, get cracked or dropped, or lose their grip on the internal shaft — all of which make it difficult or impossible to change the appliance's settings. Constructed from heat-resistant plastic with a clean white and chrome finish. Snap-on installation — no tools required. Pulls straight off the control shaft and pushes back on. This knob directly replaces WH01X24378, AP5986397, 4396548, and PS11726904. Important: this is the smaller cycle selector/options knob. If you need the larger main timer knob for your GE washer, that's a different part number (PS11736611) — check which knob is broken before ordering. Installs in under 1 minute — no tools required. Quick Answer The XPARTCO WH01X24378 Washer Cycle Selector Knob replaces a cracked, loose, stripped, or missing selector knob on GE, Hotpoint, RCA, Haier, Monogram, and Café washers and dryers. Heat-resistant plastic, white and chrome finish. Snap-on installation — pulls straight off, pushes back on. Replaces AP5986397, 4396548, PS11726904. This is the smaller cycle/options knob — NOT the larger main timer knob (PS11736611). No tools required. Common Problems This Part Fixes Selector knob cracked, broken, or split from age and repeated use Knob loose and slipping on the control shaft — no longer changes settings when turned Knob has stripped or damaged internal grip and won't stay coupled to the shaft Knob missing entirely from the control panel Knob damaged from impact — dropped or bumped Knob discolored, faded, or worn from years of daily handling Difficulty selecting cycle options — knob no longer clicks into detent positions cleanly Water or detergent damage to the knob material Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This cycle selector knob directly replaces the following OEM and cross-reference part numbers: WH01X24378, 4396548, AGE26094, AP5986397, EAP11726904, OEM17959200, PD00037085, PS11726904. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This selector knob is compatible with select washers and dryers from the following brands: GE washers — GTW500ASNWS and related top-load models GE dryers — GTX42GASJWW, GTD45GASJ2WS and related models GE Profile and GE Café washers and dryers (select models) GE Monogram washers and dryers (select models) Hotpoint washers and dryers (select models) RCA washers and dryers (select GE-built models) Haier washers and dryers (select models using GE-platform controls) Important — Two Knobs, Two Part Numbers: Many GE washers and dryers have TWO knobs on the control panel: a larger main timer/cycle knob and a smaller cycle selector/options knob. The WH01X24378 is the smaller cycle selector/options knob. If your broken knob is the larger main timer knob, you need a different part number (PS11736611 on many GE models). Before ordering, visually confirm which knob is broken and compare the size and shape to the images. Contact our support team with your model number if you're unsure. Key Features Cycle selector/options knob — used to choose specific settings within your selected wash or dry cycle Snap-on installation — pulls straight off the control shaft, pushes straight back on; no tools or hardware required Heat-resistant plastic construction — designed for years of daily use without warping or cracking Clean white and chrome finish complements GE appliance styling Ergonomic shape for comfortable grip and precise cycle selection Restores full cycle control when the original knob has cracked, stripped, or gone missing Replaces WH01X24378, AP5986397, 4396548, and PS11726904 Compatible with GE, Hotpoint, RCA, Haier, Monogram, and Café washers and dryers Important: this is the smaller cycle selector/options knob — NOT the larger main timer knob (PS11736611, sold separately) Aftermarket replacement built to OEM-equivalent quality standards Quick replacement — installs in under 1 minute Product Specifications Part Number XPWH01X24378 Part Type Washer/Dryer Cycle Selector Knob (Options Knob) Condition Aftermarket Replacement Application Washers and Dryers (GE platform) Knob Size Smaller cycle/options knob (NOT the larger main timer knob) Color White / Chrome Material Heat-resistant plastic Installation Snap-on — no tools required Larger Timer Knob Different part — PS11736611 (sold separately) Compatible Brands GE, Hotpoint, RCA, Haier, Monogram, Café Installation Notes ⚠️ Unplug Washer/Dryer Before Starting — Quick Toolless Replacement Disconnect power before beginning as a general safety precaution. Wear work gloves if desired. Locate the old cycle selector knob on the control panel of your washer or dryer. Grip the knob firmly and pull it straight off the control shaft — it should come off with a moderate pull (no tools or hardware required). If the knob is stuck or the internal grip has stripped and it's spinning without releasing, use a soft cloth wrapped around it for better grip, or gently pry it off with a plastic tool (avoid metal tools that could damage the control panel finish). Once the old knob is off, inspect the metal or plastic control shaft — if it's damaged, worn round, or spinning freely with no resistance, the underlying switch or shaft may also need replacement. If the shaft is intact, align the new WH01X24378 knob with the flat sides of the shaft (the knob has a matching D-shape or flat receiver inside) and push it firmly into place until it seats fully. Rotate the knob through its full range of positions to confirm it clicks into detents cleanly and turns smoothly. Restore power and run a test cycle. Tools needed: None (soft cloth optional). Frequently Asked Questions Is this the smaller or larger knob on my GE washer? The WH01X24378 is the smaller cycle selector (options) knob. Many GE washers and dryers have two knobs on the control panel: a larger main timer/cycle knob that selects the primary wash program, and a smaller cycle options knob (this one) that selects sub-options like temperature, spin speed, or soil level. Before ordering, look at your control panel and identify which knob has failed — if the smaller knob is broken, this is the correct part. If the larger main timer knob is broken, you need a different part (PS11736611 on many GE models). The two knobs are not interchangeable. How do I remove the old knob if it's cracked or spinning without coming off? If the internal grip on the old knob has stripped and it's spinning freely on the shaft without releasing, wrap a soft cloth around it for extra grip and pull firmly straight up. If that still doesn't work, gently pry it off with a plastic pry tool (a plastic putty knife or credit card can work). Avoid metal tools that could scratch the control panel finish. If the knob is cracked, you can sometimes break away the broken pieces to expose the internal grip on the shaft, then work each piece off. Once the old knob is off, inspect the control shaft — if it's damaged or spinning without resistance, the underlying switch may need replacement too. Do I really not need any tools for this? Correct — the WH01X24378 uses a snap-on installation with no screws or hardware. To install, align the new knob with the flat side (D-shape) of the control shaft and push it straight down until it seats fully. The whole replacement typically takes under a minute. Just make sure the knob is fully seated and rotates through all positions with the correct detent clicks before you plug the appliance back in. The knob installs fine but my washer still doesn't change settings — what next? If the new knob is installed correctly (fully seated and rotates through positions with detent clicks) but changing the knob position doesn't change the cycle behavior, the underlying selector switch or control shaft has likely failed — not the knob. Common causes include the shaft spinning freely without engaging the switch inside (the shaft has stripped or broken), or the electrical selector switch itself has failed. In these cases, replacing just the knob won't fix the problem — the switch assembly behind the panel also needs to be replaced. Contact our support team with your model number for the correct switch part number. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine GE OEM part, but is manufactured from heat-resistant plastic to match the dimensions, D-shape shaft receiver, snap-on installation, and cycle selection function of the original WH01X24378 selector knob used in compatible GE, Hotpoint, RCA, Haier, Monogram, and Café washers and dryers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

ERP IG5068 Gas Oven Igniter Replaces Part Numbers: 5303935068, 316119302, 08067970, 12874, 316T023P03, 316T023P07, 316T023P10, 316T023P12, 316T023S01, 41-201, 5303912567, 5308067970, 54099H07, AH470131, EA470131, F17-034, GR401, gr407, IGN-1, IGN-7, N316T023P10, AP2150414, PS470131, WP9751123, 9751123, 747868, 816624, AP6013893, PS11747123. Description: This Flat Style Oven Igniter Kit is a high-quality replacement part for specific Frigidaire, Whirlpool gas ranges and wall oven models. It functions to ignite the gas to light the oven burner. This does not replace round igniters, or igniters with blue ceramic.  When you turn on the oven, the igniter is activated, and it starts to glow hot. As it heats up, it ignites the gas that is released from the oven's burner. This process continues until the oven reaches the desired temperature. This is an aftermarket part that can be used as a replacement for the OEM part.

Read more less

5220FR2075LCM Washer Water Valve Three solenoid valve for cold water. Fits LG front load washers. Replaces Part Numbers: 5221ER1003A, 1268130, 5221ER1003C, 5221ER1003D, 5221ER1003F, AH3527452, EA3527452, AP4442608, PS3527452. 5220FR2075L, 4322702, AGM73269503, AP5986564, PS11728995. Description: This Water Inlet Valve Assembly is a replacement part for specific Kenmore, LG washing machine models. This critical component regulates the flow of water into the washing machine tub, ensuring the proper water supply for various wash cycles and functions.   This is an aftermarket part that can be used as a replacement for the OEM part.

Read more less

XPARTCO WB26X10038 Microwave Turntable Motor The XPARTCO WB26X10038 is an aftermarket replacement turntable motor compatible with a wide range of GE, Hotpoint, RCA, Kenmore/Sears, and Frigidaire microwaves. This small synchronous motor mounts beneath the microwave cavity floor and spins the glass turntable so food cooks and heats evenly under the magnetron. When the motor wears out or its internal gears strip, the turntable stops rotating, rotates unevenly, or starts making a grinding or clicking noise as it struggles to turn. It's built with a D-shaped 1/4" metal drive shaft and two 3/16" male spade terminals matching the original connector, so it swaps in as a direct plug-and-play replacement. It directly replaces WB26X10038, 769741, ST16F, SM16F, SSM-16H, 15QBP1017, AGE21998, AH237772, AP2024962, EA237772, OEM6074895, PD00001126, PS237772, 5304408980, 639447, AH471476, EA471476, OEM6453786, AFR80909, AP2151259, PS471476, DE31-10172A. Installs in 5–10 minutes with basic hand tools. Quick Answer The XPARTCO WB26X10038 Microwave Turntable Motor fixes GE, Hotpoint, RCA, Kenmore/Sears, and Frigidaire microwaves with a turntable that won't turn, turns unevenly, or grinds/clicks while trying to rotate. 21V AC, 50/60Hz, 2.5–3 RPM, 3.0W, D-shaped 1/4" metal shaft, two 3/16" male spade terminals. Replaces WB26X10038, 769741, ST16F, SM16F, SSM-16H, 15QBP1017, AGE21998, AH237772, AP2024962, EA237772, OEM6074895, PD00001126, PS237772, 5304408980, 639447, AH471476, EA471476, OEM6453786, AFR80909, AP2151259, PS471476, DE31-10172A. Classic symptom: microwave heats fine, but the glass tray sits still or turns only partway. Common Problems This Part Fixes Turntable doesn't rotate at all, even though the microwave heats normally Turntable turns partway then stalls or reverses Grinding, clicking, or straining noise coming from under the cavity floor Uneven cooking or hot/cold spots caused by the tray not rotating Turntable coupler or drive hub spins but the glass tray doesn't move Intermittent rotation that works sometimes and not others Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This turntable motor directly replaces the following OEM and cross-reference part numbers: WB26X10038, 769741, ST16F, SM16F, SSM-16H, 15QBP1017, MDPJ030AF, AGE21998, AH237772, AP2024962, EA237772, OEM6074895, PD00001126, PS237772, 5304408980, 639447, AH471476, EA471476, OEM6453786, AFR80909, AP2151259, PS471476, DE31-10172A, MDPJ030AF If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This turntable motor is compatible with a wide range of microwaves from the following brands: GE microwaves (JVM, DVM, EMO, and CGLMV series) Hotpoint microwaves (GE-built models) RCA microwaves (GE-built models) Kenmore and Sears microwaves (363- and 721-prefix model numbers) Frigidaire microwaves (select models sharing this motor design) Note: This motor spans both GE-built and Frigidaire microwave platforms — a cross-brand fitment worth confirming against your specific model number, since not every model on either platform uses this exact motor. Always verify your appliance model number before ordering. Contact our support team with your model number if you're unsure. Key Features Direct-fit replacement microwave turntable motor with D-shaped 1/4" metal drive shaft Resolves "won't rotate," "grinding noise," and "uneven cooking" symptoms caused by motor failure 21V AC, 50/60Hz synchronous motor rated for 2.5–3 RPM output 3.0W power draw matching original electrical specifications Two 3/16" male spade terminals for a secure plug-and-play connection CW/CCW rotation capable to match your original motor's turning direction Replaces WB26X10038, 769741, ST16F, SM16F, SSM-16H, 15QBP1017, AGE21998, AH237772, AP2024962, EA237772, OEM6074895, PD00001126, PS237772, 5304408980, 639447, AH471476, EA471476, OEM6453786, AFR80909, AP2151259, PS471476, DE31-10172AXP, and several additional cross-reference numbers Compatible with GE, Hotpoint, RCA, Kenmore/Sears, and Frigidaire microwaves Aftermarket replacement built to OEM-equivalent quality standards Product Specifications Part Number XPWB26X10038 OEM Part Number WB26X10038 Part Type Microwave Turntable Drive Motor Condition Aftermarket Replacement Voltage 21V AC Frequency 50/60 Hz Speed 2.5–3 RPM Power 3.0W Shaft Type D-shaped metal, 1/4" Diameter ~2 inches Terminals Two 3/16" male spade connectors Compatible Brands GE, Hotpoint, RCA, Kenmore, Sears, Frigidaire Installation Notes ⚠️ Unplug Microwave Before Starting Disconnect power at the outlet. For over-the-range or built-in units, most turntable motors are accessed from inside the cavity by removing the drive coupler and roller guide, then reaching the motor from underneath the cavity floor (may require removing the microwave from its mount or accessing from the bottom/rear panel, depending on model). Photograph the wiring before disconnecting. Unplug the two spade terminal connectors from the old motor. Remove the mounting screws holding the motor bracket in place and remove the old motor. Install the new WB26X10038 motor in the same position and secure the mounting screws. Reconnect the spade terminals, matching your photos (polarity typically doesn't matter on these motors, but match original wire colors when in doubt). Reinstall the drive coupler and roller guide, reassemble any panels, restore power, and test that the turntable rotates smoothly and consistently. Tools needed: Phillips screwdriver, nut driver. Frequently Asked Questions My microwave heats food fine, but the turntable doesn't spin — is this the part? Yes, this is the classic symptom of a failed turntable motor. The heating function (magnetron, high-voltage components) is a completely separate system from the turntable drive, so a microwave can heat normally while the turntable motor has failed. Before ordering, also check that the glass tray and roller guide are seated correctly, since a stuck tray can sometimes be mistaken for a motor failure. Will this fit both GE and Frigidaire microwaves? This motor design is shared across select GE-built and Frigidaire microwave models, but not every model on either platform uses it. Confirm fit using your microwave's exact model number before ordering rather than assuming by brand alone. Do I need to transfer the drive coupler from my old motor? The drive coupler (the plastic piece that connects the motor shaft to the turntable support) is typically a separate component that sits on top of the motor shaft rather than being permanently attached, so you'll generally reuse your existing coupler and roller guide with the new motor unless they're visibly worn or damaged. Why is my turntable turning slowly or grinding instead of stopping completely? This usually means the motor's internal gears are stripped or worn rather than the motor being fully dead — it's still trying to turn but can't do so smoothly. This is a sign the motor needs replacement even if it hasn't failed outright yet. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO WB03X27704 Microwave Waveguide Locking Button – Compatible with GE Microwaves Product Description Protect your microwave’s internal components with the XPARTCO WB03X27704 Microwave Waveguide Locking Button. This high-quality aftermarket replacement secures the waveguide cover in place, preventing it from shifting, falling, or allowing food splatter to enter the waveguide channel. A broken or missing locking button can lead to sparking, uneven heating, or damage to the magnetron. Replacing it with this durable XPARTCO button restores safe and reliable microwave performance. Replaces Part Numbers WB03X27704, WB02X10997, PD00045753, EAP12582530, AP6783280, 4813990, PS12582530 Compatibility This replacement waveguide locking button fits select GE countertop, over-the-range, and built-in microwaves. Example compatible models include (but are not limited to):GE JVM3160DFWW, JVM6175SK3SS, JVM7195SK5SS, PVM9005SJ2SS, and many others. Always verify your microwave’s model number before ordering. Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement – Designed to match OEM fit, size, and retention strength 🔒 Secures Waveguide Cover – Prevents shifting, sparking, or magnetron contamination 💰 Cost-Effective Solution – Affordable alternative to OEM locking buttons 🛠️ Durable Construction – Precision-molded plastic resists heat and wear 🛡️ Fixes Common Issues – Solves loose or missing cover, arcing, or uneven microwave heating 📐 Product Specification Part Number: WB03X27704 Component Type: Microwave Waveguide Cover Locking Button Material: High-strength molded plastic Color: Black (may vary slightly by batch) Mounting: Snaps into microwave cavity to retain waveguide cover Compliance: Built to OEM-equivalent quality standards (not OEM) 🛠️ Installation Notes Tools Needed: None (in most models) ⚠️ Safety First: Always unplug the microwave before servicing.Microwaves contain high-voltage components even when unplugged — avoid internal access unless qualified. Steps: Disconnect power to the microwave. Open the microwave interior and remove the damaged or missing locking button. Position the new XPARTCO WB03X27704 locking button in the designated cavity slot. Press firmly until it snaps into place. Ensure the waveguide cover is securely held. Restore power and test microwave operation. ⏱️ Time Required: 1–2 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Appliance Parts Supplier 🔄 30-Day Return Policy Protect your microwave and prevent sparking — Add to Cart Now for a fast, reliable fix!

Read more less

XPARTCO 675813 Dishwasher Thermal Fuse The XPARTCO 675813 is an aftermarket replacement bimetal thermal fuse (TCO — thermal cut-off) kit compatible with a wide range of Whirlpool-family dishwashers including Whirlpool, Kenmore, KitchenAid, Maytag, Estate, Crosley, Inglis, Roper, and Admiral. The thermal fuse is a one-time safety device located on or near the control board that monitors internal temperature. If the dishwasher overheats — due to a blocked vent, malfunctioning heating element, or other fault — the fuse permanently interrupts power to protect the dishwasher and prevent fire hazards. Unlike a resettable thermostat, a blown thermal fuse must be replaced. Once it trips, the dishwasher will show no power and will not start. The kit includes one thermal cutoff fuse with a 2-wire harness (leads extending approximately 18 inches from the fuse), one zip tie, and installation instructions. The fuse body measures 1-1/16" L x 1" W x 7/16" H. The new wiring harness must always be used when replacing the fuse. Installs in 5–15 minutes with basic hand tools. Quick Answer The XPARTCO 675813 Dishwasher Thermal Fuse Kit fixes Whirlpool-family dishwashers that show no power, won't start, have a blank control panel, or stopped mid-cycle with no response. The thermal fuse permanently trips when the dishwasher overheats and must be replaced. Kit includes fuse with 2-wire harness, zip tie, and instructions. Fuse body 1-1/16" L x 1" W x 7/16" H. Always install using the new harness included. Compatible with Whirlpool, Kenmore, KitchenAid, Maytag, and more. Common Problems This Part Fixes Dishwasher completely dead — no power, no lights, no response when buttons are pressed Control panel blank with no indicator lights or display Dishwasher stopped mid-cycle and will not restart Dishwasher will not start despite the door being closed and latched No sounds when attempting to start the dishwasher Dishwasher behaves as if it has no power even though the outlet is live Replaces Part Numbers This dishwasher thermal fuse kit directly replaces the following OEM and cross-reference part numbers: 675813, 3375557, 3376359, 675813VP, 679723, AH382828, OEM9345567, AWP39651 PD00002439, EA382828, EAP382828, AP3115186, PS382828. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This thermal fuse kit is compatible with select dishwashers from the following brands: Whirlpool dishwashers Kenmore / Sears dishwashers (Whirlpool-built models) KitchenAid dishwashers Maytag dishwashers Estate dishwashers Crosley dishwashers Inglis dishwashers Roper dishwashers Admiral dishwashers Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Bimetal thermal cut-off (TCO) fuse — permanently interrupts power if the dishwasher overheats, protecting against fire hazard One-time safety device — once tripped, the fuse must be replaced (it does not reset) Rated at 98°C — trips when internal temperature exceeds the safe operating limit Fuse body dimensions: 1-1/16" L x 1" W x 7/16" H; leads extend approximately 18" from fuse Kit includes thermal fuse with 2-wire harness, zip tie, and installation instructions Always install using the new harness included — never reuse the old harness Metal and plastic construction — reliable performance and heat resistance Direct replacement for 675813, 675813VP, 3375557, and 3376359 — no modification required Aftermarket replacement built to OEM-equivalent quality standards Quick DIY repair — installs in 5–15 minutes with basic hand tools Product Specifications Part Number 675813 Part Type Dishwasher Thermal Fuse / Thermal Cut-Off (TCO) Kit Condition Aftermarket Replacement Fuse Type Bimetal thermal cut-off (one-time, non-resettable) Trip Temperature 98°C (208°F) Fuse Body Dimensions 1-1/16" L x 1" W x 7/16" H Lead Length Approximately 18 inches from fuse body Color White / Brown Material Metal / Plastic Kit Includes Thermal cutoff fuse with 2-wire harness, zip tie, instructions Compatible Brands Whirlpool, Kenmore, KitchenAid, Maytag, Estate, Crosley, Inglis, Roper, Admiral Installation Notes ⚠️ Unplug or Switch Off Breaker Before Starting Unplug the dishwasher or turn off the circuit breaker before beginning any repair. The thermal fuse is located inside the dishwasher door panel near the control board. Open the dishwasher door and remove all screws from the inner door panel — a Torx bit is typically required on Whirlpool-family models. Carefully lift the inner door panel to expose the control board housing. Remove the black plastic cover over the control board to access the thermal fuse — it is typically on the right side of the board with one wire connected to each terminal. Test the old fuse with a multimeter for continuity (no continuity confirms the fuse has blown). Disconnect the old fuse and its harness. Connect the new 675813 fuse using the new 2-wire harness included in the kit — do not reuse the old harness. Secure the harness with the included zip tie. Reinstall the control board cover, inner door panel, and all screws. Restore power and run a test cycle. Note: If the fuse blows again after replacement, an underlying cause such as a blocked vent, failed heating element, or faulty control board should be diagnosed before replacing the fuse a second time. Tools needed: Torx screwdriver (T15 or T20), Phillips screwdriver, multimeter, work gloves. Frequently Asked Questions What does the dishwasher thermal fuse do? The thermal fuse is a one-time safety device that monitors the internal temperature of the dishwasher. If the temperature rises above the safe operating limit — 98°C in this case — the fuse permanently interrupts the electrical circuit, cutting all power to the dishwasher. This protects both the appliance and your home from fire hazard caused by overheating. Unlike a resettable thermostat, a blown thermal fuse cannot be reset and must be physically replaced. How do I know if my thermal fuse has blown? The most obvious sign is a completely dead dishwasher — no lights, no sounds, and no response when you press any buttons, even though the outlet has power. You can confirm a blown fuse with a multimeter: disconnect the fuse from the harness and test for continuity across its two terminals. A working fuse will show continuity (near-zero resistance); a blown fuse will show no continuity (open circuit). If the fuse tests bad, replace it with the 675813 kit. Why did my thermal fuse blow, and will it happen again? Thermal fuses blow when the dishwasher overheats. Common causes include a blocked air vent, a malfunctioning or shorted heating element, a failed thermostat, or an electrical fault in the control board. If you simply replace the fuse without addressing the root cause, it may blow again. After replacing the fuse, run the dishwasher and monitor for any unusual heat, steam, or burning smell. If the fuse blows again, have the underlying fault diagnosed before ordering another replacement. Why must I use the new harness and not the old one? When a thermal fuse blows, the wiring harness connected to it may have been exposed to the same overheating event that tripped the fuse. The wires or connectors may have degraded or partially melted even if they appear intact. Using the old harness risks a poor connection or a recurring fault. Always install the new 2-wire harness included in the kit to ensure a reliable, safe connection. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured from metal and plastic to match the dimensions, trip temperature, and performance of the original 675813 thermal fuse. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout  

Read more less

XPARTCO WH49X10042 Washer Agitator Coupler The XPARTCO WH49X10042 is an aftermarket replacement agitator coupling kit for GE top-load washers, and also fits select Hotpoint, RCA, Haier, Monogram, and Café models. Also known as the agitator drive bell or drive block, this small but essential part connects the transmission drive shaft to the agitator base, transmitting the back-and-forth rotational motion that lets the agitator move clothes through the wash cycle. Made of pale yellow plastic with a matte finish, this coupler measures approximately 3-7/16"L x 3-7/16"W x 3-1/8"H, and includes 1 agitator drive bell plus 1 hold-down bolt. Common causes of failure include normal wear and tear over time, or overuse with heavy or unbalanced loads that place extra strain on the coupler's plastic teeth. Symptoms of a bad coupler include the agitator not moving at all, moving too slowly or weakly, loud banging or grinding noises during operation, or oil stains appearing on clothes. It directly replaces WH43X10032, WH02X10037, WH43X10009, AH1517844, WH02X1200, WH2X10037, WH2X1200, WH43X0137, WH43X137, 175D2110P002, 175D2846P001, LP10042, 1195917, 1264702, AH1482517, EA1482517, EA1517844, EAP1517844, PD00001044, PS1482517, PS1517844, AP3964635, and AP3995059. Quick Answer The XPARTCO WH49X10042 Washer Agitator Coupler fixes GE, Hotpoint, RCA, Haier, Monogram, and Café top-load washers where the agitator won't move, moves too slowly, makes banging or grinding noise, or leaves oil stains on clothes. Pale yellow plastic, includes drive bell and bolt. Replaces WH43X10032, WH02X10037, WH43X10009, AH1517844, WH02X1200, WH2X10037, WH2X1200, WH43X0137, WH43X137, 175D2110P002, 175D2846P001, LP10042, 1195917, 1264702, AH1482517, EA1482517, EA1517844, EAP1517844, PD00001044, PS1482517, PS1517844, AP3964635, AP3995059. Several customers describe this as an easy repair — a 7/16" socket removes the bolt, and the agitator hub then pulls off by hand. Common Problems This Part Fixes Agitator not moving at all during the wash cycle Agitator moving too slowly or weakly Loud banging or grinding noise during operation Oil stains appearing on clothes after washing Agitator feeling loose or slipping when pushed or pulled by hand Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer agitator coupler directly replaces the following OEM and cross-reference part numbers: WH49X10042, WH43X10032, WH02X10037, WH43X10009, WH02X1200, WH2X10037, WH2X1200, WH43X0137, WH43X137, 175D2110P002, 175D2846P001, LP10042, 1195917, 1264702, AH1482517, AH1517844, AGE26676, AP3964635, OEM11893914, EA1517844, EAP1517844, PD00001044, PS1517844 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This agitator coupler is compatible with select GE top-load washers, and also fits select Hotpoint, RCA, Haier, Monogram, and Café washers built on the GE platform. Fits newer top-load washer designs. Note: Always verify your full model number before ordering, since GE uses different agitator coupler designs across its washer lineup. Contact our support team with your model number if you're unsure. Key Features Aftermarket replacement agitator coupling kit — also known as the agitator drive bell or drive block Connects the transmission drive shaft to the agitator base Resolves "agitator not moving," "moving too slowly," "banging or grinding noise," and "oil stains on clothes" symptoms Pale yellow plastic, matte finish Approximately 3-7/16"L x 3-7/16"W x 3-1/8"H Includes 1 agitator drive bell and 1 hold-down bolt Direct drop-in replacement matching the original mounting Replaces WH43X10032, WH02X10037, WH43X10009, AH1517844, WH02X1200, WH2X10037, WH2X1200, WH43X0137, WH43X137, 175D2110P002, 175D2846P001, LP10042, 1195917, 1264702, AH1482517, EA1482517, EA1517844, EAP1517844, PD00001044, PS1482517, PS1517844, AP3964635, and AP3995059 Compatible with GE, Hotpoint, RCA, Haier, Monogram, and Café top-load washers Aftermarket replacement built to OEM-equivalent quality standards Simple, quick DIY repair with basic tools Product Specifications Part Number XPWH49X10042 OEM Part Number WH49X10042 Part Type Washer Agitator Coupling Kit (Drive Bell) Condition Aftermarket Replacement Color Pale Yellow Material Plastic Finish Matte Dimensions 3-7/16"L x 3-7/16"W x 3-1/8"H Includes 1 agitator drive bell, 1 hold-down bolt Repair Difficulty Easy — 7/16" socket required Quantity 1 agitator coupling kit Compatible Brands GE, Hotpoint, RCA, Haier Installation Notes ⚠️ Unplug Washer Before Starting Disconnect power at the outlet before beginning. Wear work gloves. Remove the fabric softener dispenser or cap from the top of the agitator if your model has one. Using a 7/16" socket, remove the hold-down bolt securing the agitator to the transmission drive shaft. Pull the agitator straight up and off the hub — this typically comes off easily by hand once the bolt is removed. Locate the old coupler (drive bell) on the drive shaft and remove it, noting its orientation. Install the new WH49X10042 coupler onto the drive shaft in the same orientation. Place the agitator back down onto the hub, aligning it correctly, and reinstall the hold-down bolt, tightening it securely with the 7/16" socket. Reattach the fabric softener dispenser or cap. Restore power and run a test cycle to confirm the agitator moves properly through its full back-and-forth range with no unusual noise. Tools needed: 7/16" socket and ratchet, work gloves. Frequently Asked Questions My agitator isn't moving at all. Is this the part I need? Yes, this is the most common symptom of a failed agitator coupler. Since this part is what transmits rotational motion from the transmission to the agitator, worn or stripped plastic teeth inside the coupler can prevent that motion from being transferred, leaving the agitator still or barely moving even though the motor and transmission are working fine. Is this a difficult repair? No, this is one of the simpler washer repairs. Multiple customers describe it as very easy: remove a single 7/16" bolt, pull the agitator off the hub by hand, swap the coupler, and reverse the process. No special skills are typically required. Why does my washer make banging or grinding noise? A worn agitator coupler can cause this noise as its plastic components degrade and no longer mesh smoothly with the transmission shaft. Replacing the coupler typically resolves this noise along with any accompanying agitation problems. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine GE OEM part, but is manufactured to match the size, material, and drive shaft fit of the original WH49X10042 agitator coupling kit used in compatible GE, Hotpoint, RCA, Haier, Monogram, and Café top-load washers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

1408 Gas Furnace Hot Surface Igniter The 1408 is a replacement 120V silicon carbide hot surface igniter for gas furnaces. When the furnace calls for heat, the igniter glows white hot and lights the gas burners. Over time the element can crack or wear out, and a failed igniter is a common reason a gas furnace tries to start but never lights or never heats. This igniter replaces the Robertshaw 41-408 and the Rheem 62-22868-93. It is a furnace igniter, not an oven igniter, so check the part number and the look of your old igniter before ordering. Quick Answer The 1408 Gas Furnace Igniter replaces a cracked, burned-out, or failed hot surface igniter on a gas furnace that tries to start but won't light. Replaces 41-408 and 62-22868-93. Classic symptom: the inducer runs, but the igniter never glows and the burners never light. Common Problems This Part Fixes Furnace won't light, with no heat Igniter does not glow when the furnace calls for heat Cracked, broken, or visibly damaged igniter element Furnace cycles through ignition attempts and then locks out Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This igniter directly replaces the following part numbers: 1408, 41-408, 62-22868-93, 62-22868-02, 62-22868-82, 62-22441-01, 62-22868-92, B340039P01, 767A-372, 271N, IG408, 41-408, 67900, IG1408 The first three numbers are the main references for this igniter. The others appear on retailer cross-reference lists. Confirm against your furnace's parts list, or contact our support team, if your furnace calls out a different number. Compatibility This igniter is a replacement for the Robertshaw 41-408 and the Rheem 62-22868-93, and it is used on gas furnaces that call for either one. The Rheem number is used on Rheem, Ruud, WeatherKing, and Protech furnaces, including these series examples: Rheem/Ruud UGDG, UGLG, UGLH, UGPH, UGTA, UGVG Rheem/Ruud 80LJ, 80PJ, 90RJ, 90TJ Note: The series above are a sample, not a full list. Retailers do not list the lead length or connector style for this igniter, so compare your old igniter's shape, lead, and connector to the new one, and contact our support team with your furnace model number to verify fit before ordering. Key Features 120V silicon carbide hot surface igniter for gas furnaces Replaces Robertshaw 41-408 and Rheem 62-22868-93 Resolves no-light and no-heat problems caused by a failed igniter Furnace igniter, not for gas ovens Product Specifications Part Number 1408 OEM Part Number 62-22868-93, 41-408 Part Type Gas Furnace Hot Surface Igniter Condition Aftermarket Replacement Element Material Silicon Carbide Voltage 120V Application Gas Furnaces Installation Notes ⚠️ Turn Off Power and Gas Before Installing Switch off power to the furnace at the breaker and the furnace switch, and shut off the gas supply, before beginning. Wear work gloves. Let the old igniter cool, disconnect its lead, remove it, and fit the new igniter in the same position. Handle the new igniter only by its ceramic base, and avoid touching the silicon element, since skin oils can cause early failure. If the furnace still does not light, check the control board and the gas valve. Frequently Asked Questions My furnace won't light. Is this the part I need? A cracked or burned-out igniter is a common cause. If the igniter doesn't glow when the furnace calls for heat, or the element is visibly cracked, it is likely the problem. If the igniter glows but the burners don't light, check the gas valve and control. Does this replace the Robertshaw 41-408 and the Rheem 62-22868-93? Yes, it is listed as a replacement for both. Because retailers do not list lead length or connector style, compare your old igniter to this one, or contact our support team, before ordering. Why shouldn't I touch the igniter element? Skin oils on the silicon element can cause the igniter to fail early. Handle it by the ceramic base only. Will this fit my furnace? It is used on gas furnaces that call for a 41-408 or 62-22868-93 igniter, but the series list above is only a sample. Check your furnace's parts list, or contact our support team and we'll verify it before you order. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

2 Pack - XPARTCO 4933DD3001B Dishwasher Door Hinge Cable – Compatible with LG & Kenmore Dishwashers Product Description Restore smooth and controlled dishwasher door movement with the XPARTCO 4933DD3001B Dishwasher Door Hinge Cable. This high-quality aftermarket replacement connects the dishwasher door to the hinge spring system, allowing the door to open and close evenly without slamming or dropping. A worn or broken hinge cable can cause the door to fall open, feel too heavy, or fail to stay balanced. Replacing it with this durable XPARTCO cable helps restore proper door tension and safe operation. XPARTCO is a trusted aftermarket brand offering appliance replacement parts designed to meet OEM-equivalent specifications at a cost-effective price. Replaces Part Numbers 4933DD3001B, 1395107, 4933DD3001A, PD00001803, EAP3524406, AH3524406, AP4511304, EA3524406, PS3524406   Compatibility This replacement dishwasher door hinge cable fits select LG and Kenmore (LG-manufactured) dishwashers. Example compatible models include (but are not limited to):LG LDF7811ST, LDF6920STKenmore 795.13293K701, 795.13299K701 Always verify your dishwasher’s model number before ordering.Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement – Matches OEM fit, length, and tension performance 🚪 Restores Proper Door Balance – Prevents door from dropping or slamming 💪 Durable Steel Cable – Designed to withstand repeated door cycles 💰 Cost-Effective Repair – Reliable alternative to OEM hinge cables 🛡️ Fixes Common Issues – Solves loose door, uneven opening, or excessive door weight 📐 Product Specification Part Number: 4933DD3001B Component Type: Dishwasher Door Hinge Cable Material: Braided steel cable with end fittings Application: Door hinge and spring tension system Installation Side: Typically used on left or right side (model dependent) Quality Level: Aftermarket replacement (not OEM) 🛠️ Installation Notes Tools Needed: Phillips screwdriver, needle-nose pliers ⚠️ Safety First: Disconnect power to the dishwasher before servicing. Door springs are under tension—use caution during installation. Basic Steps: Disconnect dishwasher power. Remove the lower access panel. Carefully release tension from the old hinge cable. Remove the damaged cable from the hinge and spring. Install the new XPARTCO 4933DD3001B cable in the same routing. Reattach spring tension and reinstall access panel. Test door movement for smooth, balanced operation. ⏱️ Time Required: 20–30 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Aftermarket Appliance Parts 🔄 30-Day Return Policy Restore smooth, controlled dishwasher door operation — Add to Cart Now for a dependable, budget-friendly repair!

Read more less