Search results for "dryer heater"

XPARTCO DC47-00019A Dryer Heating Element Replaces WP35001247 The XPARTCO DC47-00019A is an aftermarket replacement universal-fit dryer heating element compatible with a wide range of electric dryers across multiple manufacturers — including Samsung, Whirlpool, Maytag, Amana, Inglis, and Kenmore. The heating element generates the heat that warms the air circulating through the dryer drum, evaporating moisture from wet clothes during each drying cycle. When the element fails, the dryer continues to tumble normally but produces no heat, leaving clothes damp at the end of a complete cycle. This replacement element comes pre-assembled with insulators and restring already attached, allowing for fast installation. Rated 240V, 5300W, with metal and ceramic construction. Overall dimensions are approximately 17"L x 6-1/2"W x 2-1/2"H. Important: this is a heating element assembly only — you must reuse the housing/cannister from your old element when installing the new one. It directly replaces DC47-00019A, 35001247, WP35001247, WP35001247VP, TJDC47-00019A, DE0019A, ERDC47-00019A, 35001119, 2068550, 1185561, AP4045884, AP4201899, AP6008695, AH2038533, EA2038533, EAP2038533, EAP11741835, PD00001991, PD00002996, PS2038533, PS4205218, and PS11741835. Installs in 30–45 minutes with basic hand tools. Quick Answer The XPARTCO DC47-00019A Dryer Heating Element fixes Samsung, Whirlpool, Maytag, Amana, Inglis, and Kenmore electric dryers that tumble normally but produce no heat or take much longer than usual to dry. Universal-fit element — 240V, 5300W. 17"L x 6-1/2"W x 2-1/2"H. Insulators and restring pre-attached. Must reuse the housing/cannister from the old element. Replaces DC47-00019A, 35001247, WP35001247, WP35001247VP, TJDC47-00019A, DE0019A, ERDC47-00019A, 35001119, 2068550, 1185561, AP4045884, AP4201899, AP6008695, PS2038533, PS4205218, PS11741835. Common Problems This Part Fixes Dryer tumbles normally but produces no heat — element coil burned through Dryer takes significantly longer than usual to dry a load Clothes coming out damp or only partially dried at the end of a cycle Visible breakage in the element coil — snapped or burned-through Ni-Cr wire Dryer trips the circuit breaker when the heat setting is selected — shorted element Burning smell during operation — element arcing at a weak point in the coil Multimeter continuity test on the element shows an open circuit Replaces Part Numbers This dryer heating element directly replaces the following OEM and cross-reference part numbers across multiple brands: DC47-00019A, 2068550, AP4201899, ASM33630, AP2038533, DE0019A, ERDC47-00019A, PD00001991, PS4205218, TJDC47-00019A, WP35001247, 35001247, 1185561, AP6008695, AWP47390, EAP11741835, PD00002996, PS11741835, WP35001247VP. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This universal-fit heating element is compatible with select electric dryers from multiple manufacturers: Samsung electric dryers — DV2, DV3, DV4, DV5, DVE series (DV40J3000EW, DV42H5000EW, DV42H5200EW, DV42H5600EP, DV45H7000EW, DV48H7400EW, DV50F9A7EVW, DV50F9A7EVP, DVE50M7450W, DVE50R5200W, DVE50R5400V, DV203AEW, DV206LEW, DV209AEW, DV210AEW, DV419AEU, DV448AEE, DV448AEP, DV5471AEW and many related models) Whirlpool electric dryers (select models — see WP35001247 cross-reference) Maytag electric dryers (MDE6700AYW, MDE6700AZW, MDG6700AWM, MDG6700AWW and related) Amana electric dryers (NED7200TW10, YIED7200TW10 and related) Inglis electric dryers (select models) Kenmore / Sears electric dryers (Samsung and Whirlpool-built — select models) Important — Reuse Existing Housing: This listing is for the heating element assembly only — the metal housing/cannister that the element sits inside is not included. You must reuse the housing from your old element. Remove the old element from its housing, then install the new DC47-00019A element into that same housing before reinstalling in the dryer. Also: this part is for electric dryers only — gas dryer models use different components. Always verify your specific model number before ordering. Key Features Universal-fit replacement heating element for multiple dryer manufacturers — replaces both Samsung DC47-00019A and Whirlpool/Maytag WP35001247 part numbers Generates the heat that warms drying air — essential for the dryer to actually dry clothes Pre-strung Ni-Cr (nickel-chromium) heating wire — high heat conductivity and resistance to warping over time Insulators and restring already attached — ready for installation into the existing housing Rated 240V, 5300W — correct electrical specifications for compatible electric dryers Dimensions: 17"L x 6-1/2"W x 2-1/2"H Metal and ceramic construction — durable for repeated heat/cool cycles Electric dryers only — NOT compatible with gas dryer models Important: heating element assembly only — must reuse the housing/cannister from the old element Replaces 22+ OEM and cross-reference part numbers across Samsung, Whirlpool, Maytag, Amana, and related brands Aftermarket replacement built to OEM-equivalent quality standards Quick DIY repair — installs in 30–45 minutes with basic hand tools Product Specifications Part Number XPDC47-00019A Also Replaces (Whirlpool-side) WP35001247, 35001247 Part Type Dryer Heating Element Assembly (Universal Fit) Condition Aftermarket Replacement Application Electric Dryers Only (NOT gas) Voltage 240V AC Wattage 5300W Terminal Connections 2 spade terminals Dimensions 17"L x 6-1/2"W x 2-1/2"H Material Metal / Ceramic / Ni-Cr coil wire Includes Heating element assembly with insulators and restring pre-attached (housing NOT included — reuse old) Compatible Brands Samsung, Whirlpool, Maytag, Amana, Inglis, Kenmore Installation Notes ⚠️ Unplug Dryer Before Starting — Do Not Touch the Element with Bare Hands Disconnect power before beginning. Wear work gloves throughout — there are sharp sheet metal edges inside the dryer cabinet. The new heating element coil is sensitive to skin oils, which can cause premature burnout — handle the element only by the metal frame, not the coil wire. Remove the rear panel of the dryer to access the heating element housing/cannister. Take a photo of all wire connections and the orientation of the element before disconnecting anything. Disconnect the wires from the old element terminals and remove the housing from the dryer. With the housing on a workbench, remove the old element from inside the housing — note exactly how it sits and how the restring is positioned. Install the new DC47-00019A element into the same housing, following the same orientation as the old element. Do not let the Ni-Cr heating wire touch the housing during installation — this can cause arcing and immediate burnout. Reinstall the housing in the dryer, reconnect all wires snugly to the correct terminals, and reinstall the rear panel. Restore power and run a test heat cycle to confirm the dryer is heating properly. While the rear panel is open, inspect the high-limit thermostat, thermal fuse, and thermistor — if the element failed due to overheating, these may also be stressed. Tools needed: Phillips screwdriver, 1/4" nut driver, work gloves. Frequently Asked Questions Does this really fit both Samsung AND Whirlpool dryers? Yes — this is one of the more unusual cases in dryer parts where an aftermarket heating element has been designed to serve as a direct replacement for both the Samsung DC47-00019A and the Whirlpool/Maytag WP35001247 (35001247) elements. The two OEM elements share the same physical dimensions, electrical specifications (240V, 5300W), and terminal configuration, allowing a single aftermarket element to function correctly in both platforms. Compatible models span Samsung's DV series, Whirlpool/Maytag's affected dryers (MDE6700/MDG6700 and similar), and select Amana, Inglis, and Kenmore Whirlpool-built or Samsung-built models. Always verify your specific model number before ordering. Why do I need to reuse the housing from the old element? This listing is for the heating element assembly only — the metal cannister or housing that contains the element is not included. The housing is a heavy gauge metal enclosure with mounting brackets that secure it to the dryer cabinet, along with airflow ducting that directs air across the heating coil. Reusing the housing keeps the cost down and is standard practice for this type of replacement. Carefully remove the old element from the housing, install the new element in its place, and then reinstall the housing in the dryer. If your housing is damaged or burned through, it will need to be replaced separately. How do I know if the heating element has failed? The clearest sign is a dryer that tumbles and runs through a complete cycle normally but produces little or no heat, leaving clothes damp at the end. You may also notice the dryer taking much longer than usual to dry a load as it tries to compensate. Visually inspecting the element after removing the rear panel can reveal burn marks, breaks in the coil, or visible arcing damage. A multimeter continuity test on the disconnected element will also confirm failure — a working element shows continuity, while a failed element reads an open circuit (no continuity). Should I replace the thermal fuse and thermostats at the same time? It's a good idea to inspect them. When a heating element fails — especially if it failed due to overheating rather than simple end-of-life wear — the paired thermal fuse, high-limit thermostat, and thermistor located in the same area can also be stressed by the heat event. Since the rear panel must already be open to replace the element, checking these components' continuity with a multimeter is a quick step that can prevent a repeat repair if any of them are also on the verge of failing. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Samsung or Whirlpool OEM part, but is manufactured to match the electrical specifications (240V, 5300W), dimensions, and Ni-Cr coil construction of the original DC47-00019A and WP35001247 heating elements that it replaces. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

WE11X29790 Dryer Genuine OEM Heating Element – Compatible with GE & Hotpoint Dryers Product Description Restore proper heat and efficient drying performance with the WE11X29790 Dryer Genuine OEM Heating Element. This Heater Assembly is a Genuine OEM part for specific GE dryer models. This component is responsible for generating the heat required to dry clothes effectively. It consists of a heating element and necessary components that work together to maintain the desired drying temperature, ensuring clothes come out dry and ready to wear.  Common causes of a bad heater assembly can include wear and tear from regular use, overheating, electrical issues, or damage to the heating element itself. A malfunctioning heater assembly can lead to inefficient drying or no heat at all. Replaces Part Numbers WE11X29790, PD00069983, EAP12743382, OEM20945621, AP6981872, PS12743382. Compatibility This Genuine OEM heating element fits select GE and Hotpoint electric dryers. Example compatible models include (but are not limited to):GE GTD33EASK0WW, GTD42EASJ2WW, GTD45EASJ2WSHotpoint HTDX100EM8WW, HTDX100ED6WW Always verify your dryer’s model number before ordering.Contact our support team if you’re unsure. ✅ Key Features 🧩 Genuine OEM Replacement – Factory-certified for exact fit and safe operation 🔥 Restores Proper Heating – Provides consistent, even heat for effective drying ⚙️ OEM-Grade Construction – Designed to withstand high temperatures and extended use 🛠️ Direct-Fit Installation – No modifications required 🛡️ Fixes Common Issues – Solves dryer running with no heat or weak heating 📐 Product Specification Part Number: WE11X29790 Component Type: Dryer Heating Element Voltage: 240V Wattage: OEM-specified rating Material: High-temperature resistance wire with metal housing Mounting: Heater housing assembly Compliance: Genuine OEM certified 🛠️ Installation Notes Tools Needed: Phillips screwdriver, nut driver ⚠️ Safety First: Always unplug the dryer and disconnect power before servicing to avoid electrical shock. Steps: Disconnect dryer power and remove the rear panel. Locate the heating element housing. Disconnect wiring and remove the old heating element. Install the new WE11X29790 heating element in the same position. Reconnect wiring, reinstall the panel, and restore power. Run a test cycle to confirm proper heating. ⏱️ Time Required: 20–30 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Genuine OEM Replacement Part 🔄 30-Day Return Policy Restore strong, reliable dryer heat — Add to Cart Now for a factory-quality repair!

Read more less

WP3387747 Genuine OEM Whirlpool Dryer Heating Element The WP3387747 is a Genuine OEM Whirlpool replacement dryer heating element assembly compatible with a wide range of Whirlpool, Kenmore, Maytag, Amana, KitchenAid, Roper, Estate, Crosley, Inglis, Admiral, Jenn-Air, and Magic Chef electric dryers — particularly higher-capacity and newer-generation Duet, Cabrio, HE, and GEW/GEQ series models. The heating element is the primary heat source in an electric dryer — a nickel-chromium resistance coil wound on ceramic insulators inside a steel housing. When the coil burns through, the circuit opens and the dryer produces no heat. When the coil shorts to the housing, the dryer runs too hot or heats continuously after the cycle ends — which is a fire hazard requiring immediate repair. This Genuine OEM part is manufactured by Whirlpool to factory specifications and is rated at 5200W / 240V with two 5/16" male terminals. Note: Whirlpool updated the wattage of this element from the original 5400W down to 5200W — the WP3387747 at 5200W is the correct current OEM replacement for all compatible models. The thermostat and thermal fuse are not included and should be inspected and replaced separately if needed. It directly replaces 3387747, W11344457, W11045584, 80003, 525502, AP6008281, PS11741416, and additional cross-reference numbers. Installs in 20–45 minutes with basic hand tools. Quick Answer The WP3387747 Genuine OEM Whirlpool Dryer Heating Element fixes electric dryers that produce no heat, run too hot, heat continuously, or take too long to dry. 5200W / 240V, nickel-chromium coil, two 5/16" male terminals. Thermostat and thermal fuse not included. Genuine OEM. Replaces 3387747, W11344457, W11045584, 80003, AP6008281, PS11741416. Compatible with Whirlpool Duet/Cabrio/HE/GEW/GEQ, Kenmore, Maytag, Amana, KitchenAid, Roper, Estate, Inglis, and more. Common Problems This Part Fixes Dryer produces no heat at all — element coil burned through Dryer takes much longer than normal to dry clothes Dryer tumbles normally but generates no heat during the cycle Dryer overheating or running hotter than normal — coil shorted to housing Dryer continues to heat after the cycle ends — shorted element (fire hazard) Visible break, burn spot, or sagging coil inside the housing Burning smell during operation — arcing at a weak point in the coil Dryer trips the circuit breaker when the heat cycle is selected Replaces Part Numbers This heating element directly replaces the following OEM and cross-reference part numbers: WP3387747, 3387747, 80003, W11045584, W11344457, PD00002365, EAP11741416, AP6008281, AWP47520, FIX11741416, PS11741416, WP3387747VP. Contact our support team with your model number if you need confirmation before ordering. Compatibility This heating element is compatible with select electric dryers only from the following brands and series: Whirlpool electric dryers — Duet (WED8xxx, WED9xxx), Cabrio (WED7xxx), HE series, GEW9xxx, GEQ9xxx, WED4xxx, WED5xxx and more Kenmore / Sears electric dryers — 110 series and Whirlpool-built models (including Kenmore HE2, HE3, Elite HE4, 90 series) Maytag electric dryers — MEDB, MED series Amana electric dryers KitchenAid electric dryers Roper electric dryers Estate electric dryers Crosley electric dryers Inglis electric dryers Admiral electric dryers Jenn-Air electric dryers Magic Chef electric dryers Note: This is for electric dryers only. Gas dryers use a gas burner and do not have a heating element. Also: do not touch the new element's coil wire with bare hands — skin oils degrade the nickel-chromium wire and significantly shorten element life. Handle by the frame and terminals only. Key Features Genuine OEM part manufactured by Whirlpool to factory specifications — guaranteed fit and performance Primary heat source for electric dryers — nickel-chromium resistance coil generates heat for every drying cycle Rated 5200W / 240V — current OEM wattage (updated from original 5400W by Whirlpool) Two 5/16" male terminals — matches original terminal configuration for direct wire connection Metal and ceramic construction — high-temp terminals and ceramic insulators resist heat fatigue Thermostat and thermal fuse are not included — inspect and replace separately if needed Do not touch the coil wire during installation — skin oils degrade nickel-chromium wire Replaces 3387747, W11344457, W11045584, 80003, AP6008281, and PS11741416 Compatible with Whirlpool Duet, Cabrio, HE, GEW/GEQ series and 11 additional brand platforms DIY repair — installs in 20–45 minutes with basic hand tools Product Specifications Part Number WP3387747 Part Type Dryer Heating Element Assembly (Electric) Condition Genuine OEM Application Electric Dryers Only Wattage 5200W (updated from original 5400W — current OEM spec) Voltage 240V AC Coil Material Nickel-chromium resistance wire Terminals Two 5/16" male terminals Material Metal / Ceramic Color Black / Silver Does Not Include Thermostat or thermal fuse — inspect and replace separately Handling Note Do not touch coil wire — skin oils degrade nickel-chromium wire Compatible Brands Whirlpool, Kenmore, Maytag, Amana, KitchenAid, Roper, Estate, Crosley, Inglis, Admiral, Jenn-Air, Magic Chef Installation Notes ⚠️ Unplug Dryer Before Starting — Do Not Touch the Coil Wire Disconnect power before beginning. The heating element housing is accessible from the lower front panel of the dryer on most Duet/Cabrio HE models — remove the front kick panel to access the heater housing without fully disassembling the dryer. For other models, remove the back panel. Before touching the new element, review the wiring layout of the old element so you can reconnect wires to the correct terminals. Do not touch the nickel-chromium coil wire with bare hands at any point — skin oils on the wire cause hot spots that will prematurely burn the element. Handle only by the frame, terminals, and housing. Photograph the existing wiring before disconnecting. Disconnect the element terminal wires and the thermostat and thermal fuse wires. Unscrew the housing and remove the old element. Install the new WP3387747 element, reconnect all wiring in the same positions, reinstall the housing and panels, restore power, and run a test heat cycle. Tools needed: Phillips screwdriver, 1/4" nut driver. Frequently Asked Questions My original element was 5400W but this one is 5200W — is that correct? Yes — Whirlpool intentionally updated the wattage of this heating element from 5400W to 5200W during a design revision. The WP3387747 at 5200W is the current correct OEM replacement for all compatible models that previously used the higher-wattage element. While the wattage is slightly lower, the element is designed to provide equivalent drying performance within the thermal control system of compatible dryers. The updated wattage is by manufacturer design and does not indicate a defect or an incorrect part. How do I test if the heating element has failed? Unplug the dryer and disconnect the element terminals. Set your multimeter to continuity or resistance mode. A working element shows resistance — typically around 9–12 ohms for a 5200W/240V element. An open circuit confirms the coil has burned through. Also test each terminal individually against the metal housing frame — a working element shows no continuity between either terminal and the housing. If continuity exists between a terminal and the housing, the element coil is shorted to ground and must be replaced immediately — do not operate the dryer in this condition. What is the difference between WP3387747 and 279838? Both are Genuine OEM Whirlpool dryer heating elements, but they are for different model generations and are not interchangeable. The 279838 (5400W, 240V) is for standard-capacity Whirlpool-family dryers — many WTW/NED series and standard front-load models. The WP3387747 (5200W, 240V) is for higher-capacity and newer-generation models including Whirlpool Duet, Cabrio, HE, and GEW/GEQ series. Always verify your exact model number to confirm which heating element is correct for your dryer before ordering. Why is it important not to touch the element coil wire? The heating element coil is made of nickel-chromium wire that reaches very high temperatures during operation. Oils from skin contact leave microscopic residue on the wire that creates hot spots when the element heats up — these hot spots cause premature burnout at the contaminated area, often within a few months of installation. Handle the new element by its steel frame, ceramic insulators, and terminals only. If the coil wire is accidentally touched, wipe the contact area with a dry cloth or isopropyl alcohol before installation. Is this a Genuine OEM or aftermarket part? This is a Genuine OEM part manufactured by Whirlpool to factory specifications. It is the exact same heating element assembly installed in compatible Whirlpool, Kenmore, Maytag, and related brand electric dryers from the factory — guaranteed fit, materials, and performance. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

5301EL1001J Dryer Genuine Heating Element Fits Specific LG Dryer Models. 240V, 5400W complete assembly with housing and thermostats Replaces Part Numbers: 5301EL1001J, 5301EL1001A, 1377645, AEG72910307, AH3527791, AP4439759, EA3527791, PS3527791, 5301EL1001H, 1377645, 5301EL1001E, 5301EL1001G, 5301EL1001S, 5301EL1001U, 5301EL1001W, AH3527790, AP5072170, EA3527790, PS3527790, AEG72910301, AP5669354, AEG72910309, AP7211081. Description:  This Heater Assembly is a Genuine OEM part for specific LG dryer models. This component is responsible for generating the heat required to dry clothes effectively. It consists of a heating element and necessary components that work together to maintain the desired drying temperature, ensuring clothes come out dry and ready to wear.  Causes of a bad heater assembly can include wear and tear from regular use, overheating, electrical issues, or damage to the heating element itself. A malfunctioning heater assembly can lead to inefficient drying or no heat at all. California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.go

Read more less

279838 Genuine OEM Whirlpool Dryer Heating Element The 279838 is a Genuine OEM Whirlpool replacement dryer heating element assembly compatible with a wide range of Whirlpool, Kenmore, Maytag, Amana, KitchenAid, Roper, Crosley, Estate, Inglis, Admiral, and Magic Chef electric dryers. The heating element is the primary heat source in an electric dryer — a nickel-chromium resistance coil wound around a series of ceramic insulators inside a steel housing. When electricity passes through the coil during the drying cycle, it generates the heat needed to evaporate moisture from clothes. When the element coil burns through at a weak point, the circuit is broken and the dryer produces no heat. This Genuine OEM part is manufactured by Whirlpool to factory specifications and is rated at 5400W / 240V with two 5/16" male terminals. It includes the heating element coil with partial housing and ceramic insulators already mounted — the remaining outer housing from your old assembly is reused. Note: the heating element does not include the thermostat or thermal fuse — those are separate parts. It directly replaces WP279837, 279837, 279838A, 279838VP, 3398063, 3398064, 3403585, 8565582, W10724237, 2438, AP3094254, and several additional cross-reference numbers. Installs in 20–30 minutes with basic hand tools. Quick Answer The 279838 Genuine OEM Whirlpool Dryer Heating Element fixes electric dryers that produce no heat, heat weakly, or take much longer than usual to dry clothes. 5400W / 240V, nickel-chromium coil, two 5/16" male terminals. Includes element coil with partial housing — reuses remaining outer housing from old assembly. Thermostat and thermal fuse not included. Replaces WP279837, 3398064, 3403585, 8565582, W10724237, 2438, AP3094254. Compatible with Whirlpool, Kenmore, Maytag, Amana, KitchenAid, Roper, Crosley, Estate, Inglis, Admiral, and Magic Chef electric dryers. Common Problems This Part Fixes Dryer produces no heat at all — heating element coil has burned through Dryer takes much longer than normal to dry clothes Dryer tumbles normally but generates no heat during the cycle Visible break, burn spot, or separation in the heating coil inside the housing No continuity across the heating element terminals when tested with a multimeter Burning smell from the dryer — arcing at a weak spot in the coil Dryer trips the circuit breaker when the heat cycle is selected — shorted element Replaces Part Numbers This heating element directly replaces the following OEM and cross-reference part numbers: 279838, 279837, WP279837, 2438, 279838A, 279838VP, 3398063, 3398064, 3403585, 8565582, 4531017, 4617547, 4675511, 5324919, 5329098, 5895597, W10724237, AH334313, AWP39215, EA334313, EAP334313, FIX334313, AP3094254, PD00002351, PS334313. Contact our support team with your model number if you need confirmation before ordering. Compatibility This heating element is compatible with select electric dryers only from the following brands: Whirlpool electric dryers (WED, MEDC, MEDX, Duet, Cabrio series and more) Kenmore / Sears electric dryers — 110 series and Whirlpool-built models Maytag electric dryers (MEDC, MEDX, MED series) Amana electric dryers (NED series) KitchenAid electric dryers Roper electric dryers Crosley electric dryers Estate electric dryers Inglis electric dryers Admiral electric dryers Magic Chef electric dryers Note: This is for electric dryers only. Gas dryers use a gas burner assembly and do not have an electric heating element. Always verify your dryer type and model number before ordering. When replacing the heating element, it is strongly recommended to also replace the high-limit thermostat and thermal cut-off fuse (279973 kit) — a failed element is almost always associated with an overheating event that also stresses the thermal components. Key Features Genuine OEM part manufactured by Whirlpool to factory specifications — guaranteed fit and performance Primary heat source for electric dryers — nickel-chromium resistance coil generates heat during every drying cycle Rated 5400W / 240V — correct wattage for compatible Whirlpool-family electric dryers Two 5/16" male terminals — matches the original terminal configuration for direct wire connection Includes heating element coil with partial housing and ceramic insulators pre-installed Reuses remaining outer housing from old assembly — partial housing replacement only Thermostat and thermal fuse not included — order 279973 kit separately if those also need replacement Replaces WP279837, 3398064, 3403585, 8565582, W10724237, 2438, and over 15 additional cross-reference numbers Compatible with 11 major appliance brands on the Whirlpool platform DIY repair — installs in 20–30 minutes with basic hand tools Product Specifications Part Number 279838 Part Type Dryer Heating Element Assembly (Electric) Condition Genuine OEM Application Electric Dryers Only Wattage 5400W Voltage 240V AC Coil Material Nickel-chromium resistance wire Terminals Two 5/16" male terminals Includes Element coil with partial housing and ceramic insulators — reuses remaining outer housing Does Not Include Thermostat, thermal fuse — order 279973 kit separately Often Replaced With 279973 High-Limit Thermostat and Thermal Cut-Off Kit Compatible Brands Whirlpool, Kenmore, Maytag, Amana, KitchenAid, Roper, Crosley, Estate, Inglis, Admiral, Magic Chef Installation Notes ⚠️ Unplug Dryer Before Starting — Electric Dryers Only Disconnect power before beginning. Remove the back panel of the dryer by unscrewing the perimeter screws to access the heating element housing at the lower rear of the dryer. Photograph the wiring connections before disconnecting anything. Remove the two wire connections from the element terminals and the thermostat/thermal fuse wire connections from the housing. Unscrew the heating element housing from the dryer cabinet and slide the old assembly out. Remove the inner element frame from the outer housing — the outer housing is reused. Transfer the new 279838 element (which comes with a partial housing) into the existing outer housing. Reinstall the housing into the dryer, reconnect all wiring in the same positions as photographed, reinstall the back panel, restore power, and run a test heat cycle. Tip: while the element housing is removed, inspect the thermal fuse (3392519) and high-limit thermostat/cut-off kit (279973) and replace if needed. Tools needed: Phillips screwdriver, 1/4" nut driver. Frequently Asked Questions How do I test if the heating element has failed? Unplug the dryer and remove the back panel to access the heating element housing. Disconnect the two wire terminals from the element and set your multimeter to continuity or resistance mode. Probe both terminals. A working heating element will show a resistance reading — typically between 8 and 15 ohms for a 5400W/240V element. An open circuit (no continuity / infinite resistance) confirms the element coil has burned through at a break point. You can also visually inspect the coil inside the housing for a visible gap, burn spot, or sag in the wire — any break in the coil indicates a failed element. Does this element include the thermostat and thermal fuse? No — the 279838 includes the heating element coil and partial housing only. The high-limit thermostat and thermal cut-off fuse are separate parts that mount on the element housing and are not included. When replacing the heating element, it is strongly recommended to also replace these thermal components using the 279973 thermostat kit, as a burned-out element is almost always the result of an overheating condition that also stresses the thermostat and thermal cut-off. Replacing them together ensures the heating system is fully restored and reduces the chance of a repeat failure. Why does the 279838 only come with partial housing? The 279838 heating element is designed as a replacement for the inner coil and frame assembly only — it installs inside the existing outer housing from your old assembly. The outer housing is a steel shell that does not wear out and does not need to be replaced under normal circumstances. By including only the partial housing (inner frame and coil), Whirlpool reduces part cost and simplifies installation — you simply swap the new element into your existing outer housing rather than replacing the entire assembly. Will replacing the heating element fix my dryer if the thermal fuse is also blown? Not by itself. If the thermal fuse (3392519) has also blown — which is common when the heating element fails — replacing only the element will not restore heat because the blown fuse permanently interrupts the circuit. You will need to replace both the heating element and the thermal fuse to restore normal operation. Since a thermal fuse blows due to overheating, also replacing the high-limit thermostat and thermal cut-off kit (279973) at the same time is recommended to ensure complete thermal protection is in place. Is this a Genuine OEM or aftermarket part? This is a Genuine OEM part manufactured by Whirlpool to factory specifications. It is the exact same heating element assembly installed in compatible Whirlpool, Kenmore, Maytag, and related brand electric dryers from the factory — guaranteed fit, materials, and performance. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO 279838 Dryer Heating Element The XPARTCO 279838 is an aftermarket replacement heating element for Whirlpool, Kenmore, Maytag, Amana, Roper, Estate, Crosley, Admiral, Inglis, KitchenAid, and Jenn-Air electric dryers. This element is the source of virtually all the heat in the dryer: current flows through a nickel-chromium coil, which glows and radiates heat as the blower pushes air across it and into the drum. This part is often nicknamed the "shorty" because of its compact size compared to the larger, older Whirlpool element it replaced, part number 4391960 — the shorty design is used on dryers with the lint filter positioned on the top right near the control housing. Over years of use, the coil typically fails with a visible break somewhere along its length — a section simply burns through and the circuit opens, cutting off heat entirely. A quick way to check: a healthy element reads approximately 9 to 10 ohms across its terminals with a multimeter; a reading of no resistance (open circuit) confirms the element has failed. This element shares the same dryer platform as our WP3392519 thermal fuse and works alongside a cycling thermostat and high-limit thermostat in the same heating circuit — all commonly checked or replaced together when a dryer stops heating. It directly replaces 279837, WP279837, 2438, 279838VP, 279838A, 3398063, 3398064, 3403585, 8565582, W10724237, AP3094254, AH334313, EA334313, PS334313, and PS3343130. Quick Answer The XPARTCO 279838 Dryer Heating Element fixes Whirlpool, Kenmore, Maytag, Amana, Roper, Estate, Crosley, Admiral, Inglis, KitchenAid, and Jenn-Air electric dryers with no heat, insufficient heat, or drying times that have gotten noticeably longer. Also called the "shorty" element. Replaces 279837, WP279837, 2438, 279838VP, 279838A, 3398063, 3398064, 3403585, 8565582, W10724237, AP3094254, AH334313, EA334313, PS334313, PS3343130. A healthy element reads approximately 9-10 ohms with a multimeter; if the dryer has no heat at all, also check the thermal fuse (such as our WP3392519 listing) before assuming the element is at fault — a blown fuse produces the identical symptom. Common Problems This Part Fixes Dryer runs a full cycle but produces no heat at all Dryer produces some heat, but not enough to dry clothes properly Drying times that have gotten noticeably longer than they used to Clothes coming out cold or barely warm at the end of a cycle Visible break or burned-through section in the heating coil Element that reads no resistance (open circuit) on a multimeter continuity or ohms test Dryer that heats inconsistently, cycling on and off unexpectedly Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dryer heating element directly replaces the following OEM and cross-reference part numbers: 279838, WP279837, 279837, 2438, 279838A, 279838VP, 3398063, 3398064, 3403585, 8565582, W10724237, AH334313, AP3094254, AWP39215, PD00002351, EA334313, OEM9282771, PS334313. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This heating element is compatible with select Whirlpool electric dryers, and also fits select Kenmore, Maytag, Amana, Roper, Estate, Crosley, Admiral, Inglis, KitchenAid, and Jenn-Air dryers built on the same platform, including model numbers such as: LER5624DQ0, LER4634EQ2 NED4655EW, NED4600YQ1 WED4815EW, WED4800BQ1, WED49STBW1, WED8300SW0 MEDC465HW, MEDC215EW, MEDX655DW, MEDX655DW1 RED4640YQ1, AED4675YQ1, AED4475TQ1 EED4400WQ0 Kenmore 70, 80, 90, 300, 400, 500, and 600 Series Model 110 Note: This element fits Whirlpool-platform dryers with the lint filter positioned on the top right near the control housing. It is a compact "shorty" design and is not the same element as the larger, older 4391960 used on earlier Whirlpool dryers. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Aftermarket replacement heating element — generates the heat that dries clothes Resolves "no heat," "insufficient heat," and "drying takes too long" symptoms caused by a burned-through coil Nickel-chromium coil for effective, heat-and-abrasion-resistant heating Compact "shorty" design for dryers with the lint filter near the control housing Direct drop-in replacement — no modification required Replaces 279837, WP279837, 2438, 279838VP, 279838A, 3398063, 3398064, 3403585, 8565582, W10724237, AP3094254, AH334313, EA334313, PS334313, and PS3343130 Compatible with Whirlpool, Kenmore, Maytag, Amana, Roper, Estate, Crosley, Admiral, Inglis, KitchenAid, and Jenn-Air electric dryers Aftermarket replacement built to OEM-equivalent quality standards Product Specifications Part Number XP279838 OEM Part Number 279838 Part Type Dryer Heating Element Assembly ("Shorty") Condition Aftermarket Replacement Coil Material Nickel-chromium Typical Resistance (Healthy Element) Approx. 9-10 ohms Legacy Predecessor 4391960 (larger, older design, not interchangeable) Related Components Cycling thermostat, high-limit thermostat, thermal fuse (see our WP3392519 listing) Repair Difficulty Medium — basic electrical skills and dryer panel disassembly required Quantity 1 heating element assembly Compatible Brands Whirlpool, Kenmore, Maytag, Amana, Roper, Estate, Crosley, Admiral, Inglis, KitchenAid, Jenn-Air Installation Notes ⚠️ Unplug Dryer Before Starting — Test Resistance Before Assuming It's The Element Disconnect power at the outlet or shut off the circuit breaker before beginning. Wear work gloves. Access is typically through the rear panel or the front, depending on your model, to reach the heater duct/blower housing area where the element is mounted. Before removing anything, inspect the old element visually for a break in the coil — sometimes you can see it directly, or feel it by gently wiggling each section of the coil. If nothing is visibly broken, test with a multimeter: place one probe on each terminal and look for a reading of approximately 9-10 ohms on a good element; no resistance at all confirms the element has failed. Photograph the wiring before disconnecting anything. Disconnect the wire terminals from the old element, remove the mounting screws or clips holding it in the duct housing, and pull it free. Install the new 279838 assembly in the same position, reconnect the wire terminals, and secure the mounting hardware — if the original connection wire shows burning or damage, replace it as well rather than reusing a damaged connector. Reassemble the panel, restore power, and run a test cycle to confirm the dryer is heating normally. Tools needed: 1/4" nut driver, 5/16" wrench, Phillips screwdriver, multimeter, work gloves. Frequently Asked Questions How do I test whether the element is actually bad? Start with a visual inspection — often you can see a break directly in the coil, or find it by gently wiggling each section to check for a loose or separated point. If nothing is visible, use a multimeter set to ohms and place one probe on each terminal. A good element typically reads approximately 9 to 10 ohms; a reading of no resistance at all (open circuit) confirms the element has failed and needs replacing. My dryer has no heat at all. Should I replace the element first, or check something else? Check the thermal fuse first, since a blown fuse produces the exact same "no heat at all" symptom as a failed heating element and is a cheaper, faster part to test and replace — our WP3392519 listing covers the thermal fuse used on this same dryer platform. If the fuse tests good and the dryer still has no heat, the element itself is the next thing to test. What's the difference between this "shorty" element and the older 4391960? Both are Whirlpool dryer heating elements, but this 279838 is a more compact design used on dryers with the lint filter positioned on the top right near the control housing, while 4391960 is the larger, older element used on earlier Whirlpool dryer platforms. They are not interchangeable, so confirm which style your dryer uses — checking your model number or comparing the physical size of your old element — before ordering. Should I check the connection wire while I'm replacing the element? Yes, it's worth a look. The wire connecting to the element terminals can occasionally show burning or damage if the element was arcing or overheating before it failed. If you notice any discoloration, melting, or damage on the connection wire, replace it along with the element rather than reusing a compromised connector. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured to match the nickel-chromium coil composition, resistance rating, compact "shorty" form factor, and terminal configuration of the original 279838 heating element used in compatible Whirlpool, Kenmore, Maytag, Amana, Roper, and related dryers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

Choice 8544771 Dryer Heating Element - Compatible with Whirlpool, Maytag, Kenmore, Amana Dryers Product Description Restore your dryer’s heating performance with the Replacement 8544771 Dryer Heating Element. This high-quality replacement heating element coil replaces the Whirlpool WP8544771, designed for select Whirlpool, Maytag, Kenmore, Amana, and other brand dryers. Made of durable metal and ceramic with a nickel-chromium coil, it produces 5400W at 240V to heat air for efficient drying. It fixes issues like no heat, insufficient heat, long drying times, or clothes remaining damp. Note: Requires reuse of the existing heating element housing. Inspect thermostats (e.g., 279973, 279816) and thermal fuses (e.g., 3392519) for continuity, as they often fail alongside the element. Test the coil with a multimeter before replacement to confirm failure. Replaces part numbers: WP8544771, 8544771, 1180054, W10836011, WP8544771VP,  DE771, AP6013115, PS11746337. Compatibility: Compatible with models including but not limited to: Whirlpool: WED8300SW0, WED8300SW1, WED8500SR0, WGD8300SW0, WGD8300SW1, MEDB850WB, MEDB850WL, MEDB850WR0 Maytag: 7MMGDB850WL0, 7MMGDB850WL1, MEDB200VQ0, MEDB400VQ1, MEDB700VQ0, MEDB800VB0, MEDB800VQ0, MEDB800VU0, MEDB850WB0 Kenmore: 110.67042600, 110.77086600, 110.87081601, 110.87088602 Amana: NED5800DW0, YNED5800DW0 Verify your model number or contact Parts-O-Matic support for assistance. Key Features: ✅ Brand and Models Compatibility: Fits select Whirlpool, Maytag, Kenmore, Amana, Crosley, Inglis, Roper, Admiral, Jenn-Air, Estate, and KitchenAid dryer models. 🔥 Specifications: Heater coil with 5/16" male terminals, 5400W, 240V, made of metal and ceramic with nickel-chromium wire, dimensions 13-7/8"L x 6-1/2"W x 2-1/2"H, insulators and restring pre-attached. 💰 Cost-Effective Alternative: Replacement element offers OEM-equivalent performance at a lower price. 🛠️ Easy Installation: Requires a Phillips screwdriver, 5/16" nut driver, pliers, work gloves, and multimeter; typically installed in 30–60 minutes. 🛡️ Reliable Fixes: Resolves no heat, insufficient heat, long drying times, or damp clothes after drying. Installation Notes: Tools Needed: Phillips screwdriver, 5/16" nut driver, pliers, work gloves, multimeter, flathead screwdriver. Safety First: Unplug the dryer from the power source and, for gas dryers, shut off the gas valve before installation. Shop Parts-O-Matic for high-quality replacement appliance parts with a 30-day return policy. Get your dryer back to efficient, reliable performance today! Add to cart now for a budget-friendly fix!

Read more less

XPARTCO 3387747 Dryer Heating Element Replaces WP3387747 The XPARTCO 3387747 is an aftermarket replacement heating element assembly for Whirlpool, Kenmore, Maytag, KitchenAid, Amana, and Roper electric dryers. This element is the source of virtually all the heat in the dryer: current flows through a nickel-chromium coil, which glows and radiates heat as the blower pushes air across it and into the drum. Everything downstream — the drum temperature, the drying time, the final dampness of your clothes — depends on this coil working correctly. Rated 5400W at 240V, with two 5/16" terminals for a direct connection. The nickel-chromium coil is rated at roughly 85% nickel-chromium content for effective, heat-and-abrasion-resistant heating, and it's mounted in high-temperature ceramic insulators that hold it firmly in the frame so it won't loosen or shift under the vibration of a running dryer. Over years of use, the coil itself typically fails with a visible break somewhere along its length — a section simply burns through and the circuit opens, cutting off heat entirely. It directly replaces WP3387747, WP3387747VP, W11045584, W11344457, 80003, 525502, AP6008281, AP2947033, PS344597, PS11741416, EAP11741416, FIX11741416, AWP47520, and PD00002365. Quick Answer The XPARTCO 3387747 Dryer Heating Element fixes Whirlpool, Kenmore, Maytag, KitchenAid, Amana, and Roper electric dryers with no heat, insufficient heat, or drying times that have gotten noticeably longer. 5400W, 240V, two 5/16" terminals. Replaces WP3387747, WP3387747VP, W11045584, W11344457, 80003, 525502, AP6008281, AP2947033, PS344597, PS11741416, EAP11741416, FIX11741416, AWP47520, PD00002365. If the dryer has no heat at all, check the thermal fuse first — it's a cheaper, faster fix, and a blown fuse produces the same "no heat" symptom as a failed element. Common Problems This Part Fixes Dryer runs a full cycle but produces no heat at all Dryer produces some heat, but not enough to dry clothes properly Drying times that have gotten noticeably longer than they used to Clothes coming out cold or barely warm at the end of a cycle Visible break or burned-through section in the heating coil Element that tests as an open circuit (no continuity) with a multimeter Dryer that heats inconsistently, cycling on and off unexpectedly Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dryer heating element directly replaces the following OEM and cross-reference part numbers: WP3387747, WP3387747VP, W11045584, W11344457, 80003, 525502, AP6008281, AP2947033, PS344597, PS11741416, EAP11741416, FIX11741416, AWP47520, PD00002365 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This heating element is compatible with select Whirlpool electric dryers, and also fits select Kenmore, Maytag, KitchenAid, Amana, and Roper dryers built on the same platform, including model numbers such as: GEW9200LW0, GEW9200LW1, GEW9250PL0, GEW9250PW0, GEW9250PW1 GEQ9800PW1, GEQ9800PW2 MEDB835DW4, MEDC700VW0 WED5100HW1, WED5500XW1, WED5700AC1, WED6120HW1, WED6620HW1, WED8300SW2 MED5500FW1, MED6230HW1, MED6230RHW1 Kenmore 110.82822101 Note: Always verify your full model number before ordering, since Whirlpool uses several different heating elements across its dryer lineup. Contact our support team with your model number if you're unsure. Key Features Aftermarket replacement heating element assembly — generates the heat that dries clothes Resolves "no heat," "insufficient heat," and "drying takes too long" symptoms caused by a burned-through coil Nickel-chromium coil (approx. 85% Ni-Cr content) for effective, heat-and-abrasion-resistant heating High-temperature ceramic insulators hold the coil firmly in the frame against vibration Rated 5400W at 240V Two 5/16" terminals for a direct connection Approximately 10"L x 6"W x 1"H Direct drop-in replacement — no modification required Replaces WP3387747VP, W11045584, W11344457, 80003, 525502, AP6008281, AP2947033, PS344597, PS11741416, EAP11741416, FIX11741416, AWP47520, and PD00002365 Compatible with Whirlpool, Kenmore, Maytag, KitchenAid, Amana, and Roper electric dryers Aftermarket replacement built to OEM-equivalent quality standards Product Specifications Part Number 3387747 OEM Part Number WP3387747 Part Type Dryer Heating Element Assembly Condition Aftermarket Replacement Wattage 5400 W Voltage 240V Terminals 2 (5/16") Coil Material Nickel-chromium (approx. 85% Ni-Cr) Insulators High-temperature ceramic Dimensions Approx. 10"L x 6"W x 1"H Repair Difficulty Medium — basic electrical skills and dryer panel disassembly required Quantity 1 heating element assembly Compatible Brands Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Roper Installation Notes ⚠️ Unplug Dryer Before Starting — Test Continuity Before Assuming It's The Element Disconnect power at the outlet or shut off the circuit breaker before beginning. Wear work gloves. Access is typically through the rear panel or the front, depending on your model, to reach the heater duct/blower housing area where the element is mounted. Before removing anything, test the old element with a multimeter set to continuity — a healthy element reads continuous end to end, while a failed one (with a visible break in the coil) reads open. Photograph the wiring before disconnecting anything. Disconnect the two wire terminals from the old element, remove the mounting screws or clips holding it in the duct housing, and pull it free. Install the new 3387747 assembly in the same position, reconnect the two wire terminals, and secure the mounting hardware. While the dryer is open, this is a good time to fully clean the exhaust vent ducting from the lint trap to the outside vent hood — restricted airflow is a major cause of heating element failure, and a fresh element installed into a clogged system will likely fail again prematurely. Reassemble the panel, restore power, and run a test cycle to confirm the dryer is heating normally. Tools needed: 1/4" nut driver, 5/16" wrench, Phillips screwdriver, multimeter, work gloves. Frequently Asked Questions My dryer has no heat at all. Should I replace the element first, or check something else? Check the thermal fuse first. A blown thermal fuse produces the exact same "no heat at all" symptom as a failed heating element, and it's a much cheaper, faster part to test and replace. Whirlpool's own service guidance recommends checking the thermal fuse before replacing the element. If the fuse tests good and the dryer still has no heat, the element itself is the next thing to test and likely replace. How can I tell if the element has actually failed? The most reliable way is a continuity test with a multimeter — set it to continuity mode, disconnect the element's wires, and touch a probe to each terminal. A healthy element shows continuity (a complete circuit); a failed one shows open (no continuity), which usually corresponds to a visible break or burned-through section somewhere in the coil if you inspect it closely. Why does the listing recommend cleaning the vent duct during this repair? Restricted airflow from a lint-clogged exhaust duct is one of the most common root causes of heating element failure — when air can't move through the system properly, heat builds up around the element well beyond its designed operating range, accelerating wear and often leading directly to a burned-through coil. Since you'll already have the dryer open for this repair, cleaning the full duct run from the lint trap to the outside vent hood is a good use of the same trip and helps the new element last. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured to match the 5400W/240V electrical rating, nickel-chromium coil composition, ceramic insulator mounting, and terminal configuration of the original WP3387747 heating element used in compatible Whirlpool, Kenmore, Maytag, KitchenAid, Amana, and Roper dryers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO 5300622034 Dryer Heater Restring Terminal Size: 5/16 inch 4600 Watts 240 Volts. Restring Coil for 131553900, WE14X10015 Replaces Part Numbers: 5300622034, AH451032, EA451032, OEM6405389, AP2135128, PS451032. Description:  This Electric Dryer Heating Element is a replacement part for specific Frigidaire dryer models. Located within the dryer drum cavity, this component produces the necessary hot air to evaporate moisture from wet laundry. Terminal Size: 5/16 inch.  This electric dryer heating element restring coil does not include the heater housing insulators.   This is an aftermarket part that can be used as a replacement for the OEM part. California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

WP8544772 Dryer Genuine OEM Heating Element Replaces part Numbers: WP8544772, 8544772, 1180055, AP6013116, PS11746338. Restore your dryer’s heating performance with the WP8544772 Heating Element. This Genuine OEM part is designed to provide consistent, efficient heat for drying your clothes quickly and evenly. Key Features: ✅ Genuine OEM Part – built for performance and durability 🔁 Replaces: WP8544772, 8544772, 1180055, AP6013116, PS11746338. 🔥 Produces the necessary heat for drying cycles 🛠️ Fits select Whirlpool, Kenmore, Maytag, Amana, and Crosley dryers 🧰 Easy to install – plug-and-play direct replacement ⚠️ Unplug dryer before servicing. Need help confirming fit? We’re here to assist! 📦 Part Number: WP8544772💯 30-Day Money Back Guarantee

Read more less

WP4391960 Genuine OEM Whirlpool Dryer Heating Element The WP4391960 is a Genuine OEM Whirlpool replacement dryer heating element used in older-generation Whirlpool-family electric dryers, including Whirlpool, Kenmore, Roper, Estate, Amana, and Admiral models — particularly the LE, EL, and early LG series dryers. The heating element is the primary heat source in an electric dryer — a nickel-chromium resistance coil wound around ceramic insulators inside a steel housing that generates heat when electrical current passes through it. When the coil burns through, the circuit opens and the dryer produces no heat. A shorted coil that contacts the housing is a fire hazard and requires immediate replacement. This Genuine OEM part is manufactured by Whirlpool to factory specifications and is rated 5200W / 240V with 1/4" male spade terminals. Note: this element uses 1/4" terminals — different from the 5/16" terminals on the 279838 and WP3387747 elements. The wire kit and wire nuts (part 279457) are no longer included with this element and must be ordered separately if the original wires are damaged. It consolidates a very large list of older cross-reference numbers including 4391960, 2013, 279247, 279248, 279410, 279411, 696579, 696326, 697290, 786077, AP6009347, PS11742505, and dozens more. Installs in 20–45 minutes with basic hand tools. Quick Answer The WP4391960 Genuine OEM Whirlpool Dryer Heating Element fixes older Whirlpool-family electric dryers (LE, EL, early LG series) that produce no heat, run too hot, or take too long to dry. 5200W / 240V, 1/4" male spade terminals (not 5/16"). Wire kit 279457 sold separately — not included. Genuine OEM. Replaces 4391960, 2013, 279247, 279248, 279410, 279411, 696579, AP6009347, PS11742505, and many more. Compatible with older Whirlpool, Kenmore, Roper, Estate, Amana, and Admiral electric dryers. Common Problems This Part Fixes Dryer produces no heat — element coil burned through Dryer takes much longer than normal to dry a load Dryer tumbles normally but produces no heat at all during the cycle Dryer overheating or running continuously — coil shorted to housing (fire hazard) Visible break, burn spot, or collapsed section in the heating coil Burning smell during operation — arcing at a weak point in the coil Dryer trips the circuit breaker when the heat cycle is selected Replaces Part Numbers This heating element directly replaces the following OEM and cross-reference part numbers: WP4391960, 4391960, 2013, 279218, 279247, 279248, 279410, 279411, 279455, 279598, 279698, 3367, 337378, 337430, 339655, 340468, 348775, 349542, 349543, 349545, 349546, 660933, 660982, 685182, 685942, 689805, 689980, 690241, 690983, 691724, 692758, 693061, 693062, 693297, 693298, 693299, 693300, 695182, 696324, 696326, 696579, 697290, 786077, 8218, 8700-599, WP4391960VP, AWP47415, DE177, DE193, DE195, DE698, EAP11742505, ER4391960, AP6009347, PD00002385, PS11742505, TJ90DE698. Contact our support team with your model number if you need confirmation before ordering. Compatibility This heating element is compatible with select older-generation electric dryers only from the following brands: Whirlpool electric dryers — LE, EL, and early LG/LER series (older models) Kenmore / Sears electric dryers — older 110-series models (Whirlpool-built) Roper electric dryers Estate electric dryers Amana electric dryers (older models) Admiral electric dryers Important: The WP4391960 uses 1/4" male spade terminals — different from the 5/16" terminals on the 279838 and WP3387747 elements. Verify your existing element's terminal size before ordering. Also: the wire kit (part 279457) is no longer included with this element — order separately if needed. Always verify your exact model number before ordering. Key Features Genuine OEM part manufactured by Whirlpool to factory specifications — guaranteed fit and performance Primary heat source for older Whirlpool-family electric dryers — nickel-chromium resistance coil Rated 5200W / 240V — correct electrical specifications for compatible older-generation dryer models 1/4" male spade terminals — different from the 5/16" terminals on 279838 and WP3387747; verify before ordering Consolidates over 50 older cross-reference part numbers into a single current OEM part Wire kit (part 279457) no longer included — order separately if original wires are damaged Do not touch the element coil with bare hands — skin oils cause premature burnout Compatible with Whirlpool LE/EL series, Kenmore older 110-series, Roper, Estate, Amana, and Admiral electric dryers DIY repair — installs in 20–45 minutes with basic hand tools Product Specifications Part Number WP4391960 Part Type Dryer Heating Element (Electric) Condition Genuine OEM Application Older-Generation Electric Dryers (LE, EL, early LG/LER series) Wattage 5200W Voltage 240V AC Coil Material Nickel-chromium resistance wire Terminals 1/4" male spade terminals (not 5/16") Wire Kit Not included — order part 279457 separately if needed Handling Note Do not touch coil wire — skin oils cause premature burnout Compatible Brands Whirlpool, Kenmore, Roper, Estate, Amana, Admiral Installation Notes ⚠️ Unplug Dryer Before Starting — Do Not Touch the Coil Wire Disconnect power before beginning. Remove the back panel of the dryer to access the heating element housing. On older LE-series Whirlpool models, the element housing is mounted at the lower rear of the dryer and may have a top panel over the housing that must be removed before the element can be freed. Photograph all wiring before disconnecting. Note: the element's wires and wire nuts (279457 kit) are no longer included with the WP4391960 — if your existing wires are in good condition, reuse them; if damaged, order 279457 separately before beginning. Do not touch the new element's coil wire at any point — skin oils create hot spots that will prematurely burn the element. Disconnect the old element wires, unscrew the housing mounting screws, and remove the old element. Install the new WP4391960 in the same orientation, reconnect wiring, reinstall the housing, and restore power. Run a test heat cycle to confirm normal operation. Tools needed: Phillips screwdriver, 1/4" nut driver. Frequently Asked Questions What is the difference between WP4391960 and 279838 or WP3387747? All three are Genuine OEM Whirlpool dryer heating elements, but for different generations of dryers and with different terminal sizes. The WP4391960 (5200W, 1/4" spade terminals) is for older-generation Whirlpool LE/EL series and early Kenmore dryers. The 279838 (5400W, 5/16" terminals) is for standard-capacity mid-generation Whirlpool-family dryers. The WP3387747 (5200W, 5/16" terminals) is for newer higher-capacity models like the Duet, Cabrio, HE, and GEW/GEQ series. The terminal size difference is important — the WP4391960 uses 1/4" spade terminals, while the other two use 5/16" terminals. Always verify your model number before ordering. Why does this element have so many cross-reference part numbers? The WP4391960 consolidates a very large number of older Whirlpool heating element part numbers that were used across many different model runs over the years. As Whirlpool refined the design and standardized parts across its lineup, it consolidated these older numbers into the current WP4391960. If your dryer's parts diagram shows any of the hundreds of older cross-reference numbers listed above, the WP4391960 is the correct current replacement. Why is the wire kit (279457) not included? Whirlpool changed the packaging of this part during a production revision and no longer includes the wire kit and wire nuts that were previously bundled with the element. If your existing element wires are in good condition, you can reuse them — carefully transfer each wire to the corresponding terminal on the new element, maintaining the original connections. If any wires are burned, melted, or damaged, order part 279457 (wire kit) separately before beginning the repair. How do I test if the heating element has failed? Unplug the dryer and disconnect the element terminals. Set your multimeter to continuity or resistance mode. A working 5200W/240V element shows a resistance reading — typically around 9–12 ohms. No continuity (open circuit) means the coil has burned through. Also test each terminal individually to the metal housing frame — if continuity exists between a terminal and the housing, the element is shorted to ground and must be replaced immediately as a fire hazard. Is this a Genuine OEM or aftermarket part? This is a Genuine OEM part manufactured by Whirlpool to factory specifications. It is the exact same heating element installed in compatible older-generation Whirlpool, Kenmore, Roper, and related brand electric dryers from the factory — guaranteed fit, materials, and performance. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

WP3387749 Dryer Genuine OEM Heating Element – Compatible with Whirlpool, Kenmore, Maytag Dryers Product Description Restore your dryer’s heating performance with the WP3387749 Dryer Genuine OEM Heating Element. This factory-approved replacement part generates the heat needed to dry laundry efficiently. A failed heating element may cause your dryer to run but not heat, take longer to dry clothes, or shut down during cycles. Replacing it with this genuine OEM part ensures safe operation and long-lasting performance. Replaces Part Numbers WP3387749, 3387749, 525504, PD00003387, EAP344599, AP6008283, PS11741418. Compatibility This heating element is compatible with select Whirlpool, Kenmore, Maytag dryers. Example compatible models include (but are not limited to): Whirlpool LER4634EQ2, Kenmore 110.96573220, and Maytag MEDC215EW1. Always verify your dryer’s model number before ordering. Contact our support team if you’re unsure. ✅ Key Features 🔄 Wide Compatibility – Fits Whirlpool, Kenmore, Maytag dryers 🔥 Restores Heating – Generates reliable, consistent heat for drying 💰 Cost-Effective OEM Repair – Genuine part ensures durability and performance 🛠️ DIY Friendly – Installs with standard tools in under 30 minutes 🛡️ Fixes Common Issues – Solves no-heat problems, long drying times, or mid-cycle shutdowns 📐 Product Specification Part Number: WP3387749 Component Type: Dryer Heating Element Material: High-temperature resistant metal coil with mounting housing Mounting: Direct replacement heating element assembly Operating Conditions: Designed for residential dryers Compliance: Genuine OEM certified 🛠️ Installation Notes Tools Needed: Nut driver, Phillips screwdriver, needle-nose pliers ⚠️ Safety First: Always unplug the dryer before beginning repairs to prevent electrical shock. Steps: Disconnect power and remove dryer rear access panel. Locate the heating element housing inside the dryer. Disconnect wire terminals and remove screws securing the old element. Slide out defective element and install the new WP3387749. Reconnect wires, secure housing, and reinstall rear panel. Restore power and test dryer heating. ⏱️ Time Required: 20–30 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders 🛠️ Trusted Appliance Parts Supplier 🔄 30-Day Return Policy Get your dryer heating again — Add to Cart Now for a safe, factory-approved repair! WP3387749 Dryer Genuine OEM Heating Element Cross Reference Information   Part Number WP3387749, 3387749, 525504, PD00003387, EAP344599, AP6008283, PS11741418.

Read more less