WB24X25013 Genuine OEM GE Range Surface Burner Infinite Switch Replaces WB24X47186.
The WB24X25013 is a genuine GE OEM infinite control switch for a dual (bridge) surface element on GE, Hotpoint, and select Kenmore electric ranges — the kind of burner with an inner coil and an outer coil that can be run together for a large pot or as the inner coil alone for a small pan. Because it's governing two coil zones instead of one, this switch uses six terminal connections rather than the three or four found on a standard single-element infinite switch, and it mounts to the control panel with a distinctive figure-8 style shaft and two female mounting holes.
Like any infinite switch, it doesn't have fixed heat positions — instead it rapidly cycles power to the element(s) on and off at a ratio set by the knob, giving continuous heat adjustment from warm to high rather than a handful of steps. Rated for 240VAC at 15 amps. Over years of cycling, the internal contacts on a switch like this wear, pit, or weld together, and boilovers or spills can corrode the switch body and cause it to fail. A worn switch on a dual-element burner can produce an unusually wide symptom set: the whole burner may fail, or just the outer ring may stop responding while the inner coil still works, or the burner may stay on continuously regardless of the knob position. It directly replaces WB24X47186, 191D4774P005, AP5999509, PS11729102, EAP11729102, and 4464832. As a genuine OEM part, the WB24X25013 is manufactured by GE to factory specifications — guaranteed fit, materials, and performance.
Quick Answer
The WB24X25013 Genuine OEM GE Range Surface Burner Infinite Switch fixes GE, Hotpoint, and Kenmore electric ranges with a dual (bridge) element burner where the burner won't turn on or off, only the outer ring fails to work while the inner coil still heats, the burner stays on continuously, or heat can't be adjusted. Six-terminal switch, figure-8 shaft, 240VAC / 15A. Replaces WB24X47186, 191D4774P005, AP5999509, PS11729102, EAP11729102, 4464832. Not the same switch as a standard single-element infinite switch — this one is specific to dual/bridge burners with an inner and outer coil.
Common Problems This Part Fixes
Dual-element burner won't turn on at all when the knob is turned
Outer ring of a dual/bridge element won't activate while the inner coil still works
Burner won't turn off — stays hot even with the knob at the off position
Burner stuck at one heat level regardless of where the knob is set
No ability to adjust temperature — always full blast or always low
Intermittent burner operation — works sometimes, not others
Knob feels loose, gritty, or doesn't turn smoothly through its range
Burner failure that followed a boilover or liquid spill on the control panel
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This range surface burner infinite switch directly replaces the following OEM and cross-reference part numbers:
WB24X25013, WB24X47186, 191D4774P005, AGE1543754, AP7216136, PS11729102, PS17872685, EAP11729102, 4464832, 191D4774P005, MDSA-W767-GEM
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This dual-element infinite switch is compatible with select GE, Hotpoint, and Kenmore electric ranges equipped with a dual (bridge) surface element, including model families such as:
GE JB6, JB7, and JB8 series electric ranges (including JB630, JB640, JB645, and JB655)
GE JBS series electric ranges
GE JS6 and JS7 series electric ranges (including the JS760 series)
GE GRS and GRF series electric ranges
Hotpoint electric ranges (select GE-built models)
Select Kenmore electric ranges built on the GE platform
Verified model numbers include: JB645RK6SS, JS760EP6ES, JS760DP6WW, JS760SP7SS, JS760DP7WW, JS760SP6SS, JS760FP7DS, JS760FP6DS, JS760EP7ES, JB860EJAES, JB860FJADS, and GRS500PV1SS.
Note: This is a six-terminal switch built specifically for a dual (bridge) element with a figure-8 style shaft and two female mounting holes — it is NOT interchangeable with a standard single-element infinite switch such as the WB24T10029 or WB24T10025, which use fewer terminals and a different shaft profile. Fitting a standard single-element switch to a dual-element burner circuit will not correctly control both coil zones. Always verify your full model number and confirm the affected burner is a dual/bridge element before ordering. Contact our support team with your model number if you're unsure.
Key Features
Genuine GE OEM part — factory-specified contact design for dual-element switching
Six-terminal design controls both the inner coil and outer ring of a dual (bridge) surface element
Figure-8 style shaft with two female mounting holes matched to the original control panel bracket
Infinite switch design allows continuous heat adjustment rather than a handful of fixed positions
Rated 240VAC at 15 amps
Resolves "burner won't turn on," "outer ring not working," "won't turn off," and "stuck at one heat level" symptoms caused by worn or corroded switch contacts
Direct drop-in replacement — mounts to the same control panel bracket and wiring harness
Replaces 191D4774P005, AP5999509, PS11729102, EAP11729102, and 4464832
Genuine OEM replacement — guaranteed fit, materials, and performance
Product Specifications
Part Number
WB24X25013
Part Type
Range Surface Burner Infinite Switch (Dual/Bridge Element)
Condition
Genuine OEM
Brand
GE
Element Type Controlled
Dual (bridge) surface element — inner coil + outer ring
Terminal Connections
6
Shaft Style
Figure-8
Mounting
Two female mounting holes
Voltage
240VAC
Amperage
15A
Function
Cycles element power to allow continuous (infinite) heat adjustment across both coil zones
Quantity
1 switch
Compatible Brands
GE, Hotpoint, select Kenmore
Installation Notes
⚠️ 240V Circuit — Unplug Range Or Shut Off Breaker Before Starting Disconnect power at the outlet or shut off the circuit breaker before beginning — this switch operates on a 240V circuit, and working on it while powered presents a serious shock hazard. Wear work gloves. Remove the burner knob (it typically pulls straight off, though some models use a small retaining clip) then remove the screws securing the control panel or backsplash to reach the switch from behind. Photograph the wiring before disconnecting anything — this is a six-terminal switch, and getting even one wire out of place can miswire the inner coil, the outer ring, or both. Label each wire as you remove it. Disconnect all six terminal connections from the old switch, then remove the mounting screws from the two mounting holes and pull the switch free from its figure-8 shaft opening. Install the new WB24X25013 in the same orientation, reconnect each of the six wires exactly as labeled, and secure the mounting hardware. Reinstall the control panel or backsplash, press the knob back onto the shaft, restore power, and test the burner at every knob position — confirm the inner coil and outer ring both activate correctly (together and, if your model supports it, with the outer ring switched off independently) before considering the repair complete. Tools needed: Phillips screwdriver, nut driver, wire terminal pliers (helpful but optional), work gloves.
Frequently Asked Questions
How do I know if my burner uses a dual-element switch like this one?
Look at the burner element itself: a dual (bridge) element has two distinct coil rings — a smaller inner coil and a larger outer ring — usually with a separate control or a knob position that lets you activate just the inner coil for a small pan or both rings together for a large pot. A standard single-ring element has only one coil and uses a simpler switch with fewer terminals. If your range has this two-ring burner design, the WB24X25013 (or the exact switch behind it) is the correct type — but always confirm your model number, since dual-element switches vary by range generation.
Only the outer ring of my dual burner doesn't work. Is it the switch or the element?
It could be either, and it's worth narrowing down before ordering. If the inner coil heats normally but the outer ring never activates at any knob position, check the outer ring element itself first — a broken element coil is a common and cheaper fix than a switch. If the outer ring element tests fine but the switch's six-terminal wiring specific to the outer coil circuit has failed or corroded, the infinite switch is the correct replacement.
Can I use a standard single-element infinite switch instead if this one is out of stock?
No. A standard single-element switch has fewer terminals and cannot correctly control the two separate coil zones of a dual (bridge) burner. Wiring a single-element switch into a dual-element circuit will leave one coil zone permanently uncontrolled or non-functional. Always order the six-terminal dual-element switch specified for your model.
What does "infinite switch" mean?
An infinite switch lets you dial in a continuous range of heat rather than a few fixed positions, by rapidly cycling the element's power on and off at a ratio set by the knob — low settings get short power pulses, high settings get long ones. When the internal contacts wear or weld together from years of cycling, the switch can get stuck feeding constant power (burner always hot) or stop switching at all (burner always off), regardless of where the knob is turned.
A spill got into the control panel and now the burner won't turn off. Is that the switch?
Very likely, yes. Liquid boilovers and spills are one of the most common causes of infinite switch failure — moisture gets into the switch body, corrodes or bridges the internal contacts, and the switch can end up stuck feeding power continuously even with the knob turned to off. If you suspect this, shut off power to the range immediately at the breaker rather than relying on the knob, since a shorted switch may not respond to it at all.
Is this an OEM or aftermarket part?
This is a genuine OEM part, manufactured by GE to factory specifications — guaranteed fit, materials, and performance. It matches the original six-terminal wiring, figure-8 shaft, 240VAC/15A electrical rating, and dual-coil switching behavior of the infinite switch originally installed for the dual (bridge) element in your GE, Hotpoint, or Kenmore range.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
W11025156 Genuine OEM Whirlpool Dryer Heating Element
The W11025156 is a genuine Whirlpool OEM heating element for Whirlpool, Kenmore, and Maytag electric dryers. This element is the source of virtually all the heat in the dryer: it converts electrical energy into heat, which the blower then circulates through the drum to dry your clothes. Even heat distribution from a properly functioning element is what keeps drying times consistent and prevents the dryer from having to run longer cycles to compensate.
Over years of use, the coil typically fails with a visible break somewhere along its length — a section simply burns through and the circuit opens, cutting off heat entirely. Symptoms of a failing element include clothes taking too long to dry, clothes coming out cold, or the dryer not heating at all. This part is also essential for preventing overheating, since a properly functioning element operates within its designed parameters rather than drawing excess current trying to compensate for a partial failure. It directly replaces W10608823.
Quick Answer
The W11025156 Genuine OEM Whirlpool Dryer Heating Element fixes Whirlpool, Kenmore, and Maytag electric dryers with no heat, insufficient heat, or drying times that have gotten noticeably longer. Replaces W10608823. Before replacing, clean out or inspect your exhaust venting — restricted airflow is a common cause of premature heating element failure, and a fresh element installed into a clogged system is likely to fail again.
Common Problems This Part Fixes
Dryer runs a full cycle but produces no heat at all
Dryer produces some heat, but not enough to dry clothes properly
Drying times that have gotten noticeably longer than they used to
Clothes coming out cold or barely warm at the end of a cycle
Visible break or burned-through section in the heating coil
Dryer not drying laundry despite completing a normal cycle
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This dryer heating element directly replaces the following OEM and cross-reference part numbers:
W11025156, W10608823, 4461512, W10608823, AP6037386, AWP42261, EAP11770230, PD00034419, PS11770230.
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This heating element is compatible with select Whirlpool electric dryers, and also fits select Kenmore and Maytag dryers built on the same platform, including model numbers such as:
MEDB855DC2, MEDB955FC1, MEDB955FW1 (Maytag)
YWED8000DW1, YWED8500DW1, WED9500EC0, WED9500EW0, WED8700EC2
Kenmore 11061632610, 11061632611, 11061632612, 11061633610, 11061633611
Kenmore 11068132411, 11068132412, 11068132413, 11068133411, 11068133412, 11068133413
Kenmore 11069132411, 11069132412, 11069132413, 11069133411, 11069133412, 11069133413
Kenmore 110C61633610, 110C68132413
Note: Always verify your full model number before ordering, since Whirlpool uses several different heating elements across its dryer lineup. Contact our support team with your model number if you're unsure.
Key Features
Genuine Whirlpool OEM part — factory-specified coil design and electrical rating
Converts electrical energy into heat, circulated through the drum by the blower
Resolves "no heat," "insufficient heat," and "drying takes too long" symptoms caused by a burned-through coil
Ensures even heat distribution for consistent drying performance
Direct drop-in replacement — no modification required
Replaces W10608823
Compatible with Whirlpool, Kenmore, and Maytag electric dryers
Genuine OEM replacement — guaranteed fit, materials, and performance
Product Specifications
Part Number
W11025156
Part Type
Dryer Heating Element
Condition
Genuine OEM
Brand
Whirlpool
Function
Generates heat to dry clothes, circulated through the drum
Repair Difficulty
Medium — basic electrical skills and dryer panel disassembly required
Quantity
1 heating element
Compatible Brands
Whirlpool, Kenmore, Maytag
Installation Notes
⚠️ Unplug Dryer Before Starting — Clean The Vent While You Have The Panel Open Disconnect power at the outlet or shut off the circuit breaker before beginning. Wear work gloves. Access is typically through the back panel: a 1/4" ratchet with a 5/16" socket handles most of the screws, and using a socket adapter on a screw gun can speed up removing and reinstalling the panel, since there are several screws to deal with. With the panel off, locate the heating element in the duct housing. Photograph the wiring before disconnecting anything. Disconnect the wire terminals from the old element, remove the mounting screws or clips holding it in the duct housing, and pull it free. Install the new W11025156 in the same position, reconnect the wire terminals, and secure the mounting hardware. While the dryer is open, this is a good time to fully clean the exhaust vent ducting from the lint trap to the outside vent hood — restricted airflow is a major cause of heating element failure, and a fresh element installed into a clogged system will likely fail again prematurely. Reassemble the panel, restore power, and run a test cycle to confirm the dryer is heating normally. Tools needed: 1/4" ratchet, 5/16" socket, work gloves.
Frequently Asked Questions
My dryer runs a full cycle but the clothes are still wet. Is this the heating element?
It's a strong possibility, especially if you've noticed drying times gradually getting longer before the dryer stopped heating altogether. One customer described exactly this symptom — "dryer not drying laundry" — and resolved it with this exact replacement element.
Do I need any special tools for this repair?
Just basic hand tools. A 1/4" ratchet with a 5/16" socket handles the back panel screws on most models. Using a socket adapter on a screw gun can speed up the process, since there are several screws to remove and reinstall on the back panel alone.
Why does the listing recommend cleaning the vent during this repair?
Restricted airflow from a lint-clogged exhaust duct is one of the most common root causes of heating element failure — when air can't move through the system properly, heat builds up around the element well beyond its designed operating range, accelerating wear and often leading directly to a burned-through coil. Since you'll already have the dryer open for this repair, cleaning the full duct run from the lint trap to the outside vent hood is a good use of the same trip and helps the new element last.
Is this an OEM or aftermarket part?
This is a genuine OEM part, manufactured by Whirlpool to factory specifications — guaranteed fit, materials, and performance. It matches the original coil design and electrical rating of the heating element originally installed in your dryer.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
S48D21 8" Range Surface Element
Product Title
Aftermarket S48D21 8" Range Surface Element - Compatible with Whirlpool, Maytag, Kenmore, Jenn-Air, Amana Electric Ranges
Product Description
Revive your electric range’s cooking performance with the Aftermarket S48D21 8" Range Surface Element from Parts-O-Matic. This high-quality aftermarket burner element replaces the original S48D21, delivering 2100 watts at 240V with a 4-turn coil design for efficient and even heating. Ideal for select Whirlpool, Maytag, Kenmore, Jenn-Air, Amana, and other brand electric ranges, it addresses issues like uneven heating, slow warm-up, or non-functional burners. Enjoy free shipping on all orders at Parts-O-Matic!
Key Features:
✅ Broad Compatibility: Fits select Whirlpool, Maytag, Kenmore, Jenn-Air, Amana, and other electric range models.
🔥 Efficient Heating: 8" diameter, 4-turn coil delivers 2100 watts at 240V for consistent, even cooking.
💰 Cost-Effective Alternative: Aftermarket part offers OEM-equivalent performance at a lower price.
🛠️ Easy Installation: Plug-in design with Y-style bracket; requires no tools and takes 5–10 minutes to install.
🛡️ Fixes Common Issues: Resolves uneven heating, slow warm-up, or burners that fail to heat.
Compatibility:
Compatible with models including but not limited to:
Whirlpool: RF110AXSQ0, RF262LXSB, RF365PXKW0
Maytag: MER4110AAH, MER4120AAQ
Kenmore: 629.4297, 629.60003600 (pre-2004 models)
Jenn-Air: JES9750AAB
Amana: AER5511AAQ
Replaces part numbers: TJ90SP21MA, 14215226, 1938283, 309917, 403782, 404110, 406000, 814154, ERS48D21, SE302, SP21MA, SU214, SU302, TS4D8221, TS4D8221PB, TS4D8221SR, TS4D8221WI, YSP21MA, AP4503257.
Verify compatibility with your appliance brand and model number, please contact Parts-O-Matic support for assistance.
Installation Notes:
Tools Needed: None for standard installation; a flathead screwdriver may help for stubborn connections.
Safety First: Unplug the range before installation to avoid electrical shock.
Steps: Remove the old burner element by gently pulling it from the receptacle, align the Y-style bracket of the new S48D21 element, and plug it into the socket. Ensure the element sits flat in the drip pan. If the burner is not level, adjust the connection bolts to ensure they are parallel and push down gently. Installation takes 5–10 minutes. Note: A slight burning smell during first use is normal due to a protective coating; this will dissipate after 15–20 minutes.
Download our installation guide or watch our YouTube tutorial for step-by-step instructions.
Shop Parts-O-Matic for high-quality aftermarket appliance parts with free shipping on all orders and a 30-day return policy. Restore your range’s cooking performance today!
Add to cart now for an affordable fix with free shipping on your entire order!
WD12X10304 Genuine GE OEM Rack End Cap Clip
Replaces Part Number: WD12X10304, 1556527, WD12X0344, WD12X344, WD30X97, AH2370502, EA2370502, OEM13454003, AP4484666, PS2370502.
Description: This Rack Slide End Cap is a Genuine OEM part for specific GE dishwasher models. This small but essential component is designed to secure the end of the rack slide rail, preventing the dish racks from sliding off the track or becoming misaligned.
California Residents only
WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov
WD26X25104 Dishwasher Genuine OEM Drain Pump
Fits Specific GE Dishwasher Models.
Replaces Part Numbers: WD26X25104, WD26X22810, WD26X20306, AP6990087, PS16217045
Description: The Variable Drain Pump Kit is a Genuine OEM replacement part for select GE built-in dishwasher models. It includes both the drain pump and clamps needed to remove water from the dishwasher during cycles. Common causes are blockages in the drain hose inhibiting water outflow or failure of the electric pump motor components over extended use.
8270020CM Dishwasher Door Spring
Door balance spring - 7.75" overall length.
Fits Whirlpool dishwashers.
Replaces Part Numbers:WP8270020, 8270020, AP6012319, PS11745526.
This is an aftermarket part that can be used as a replacement for the OEM part.
California Residents only
WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov
4 Pack - XPARTCO DD66-00023A Dishwasher Lower Dish Rack Roller - Compatible with select Samsung models
Product Description
Restore smooth operation to your dishwasher with the XPARTCO DD66-00023A Dishwasher Lower Dish Rack Roller. This replacement roller is designed as a replacement for select Samsung dishwashers, offering a cost-effective alternative to the original. It supports the lower dish rack, ensuring it glides smoothly in and out for easy loading and unloading. This part addresses issues like the rack sticking, wobbling, or falling off the rails, often caused by worn or broken rollers.
Note: Includes (1) lower dish rack roller. Disconnect power before installation. Verify compatibility with your dishwasher model.
Replaces part numbers: DD66-00023A, PD00002184, EAP4222532, DW0023A, AP4342187, 2002711, PS4222532.
Compatibility:
Compatible with select Samsung dishwasher models, including but not limited to:
Samsung: DW80J3020US/AA-0000, DW80J3020US/AA-0001, DW80J3020US/AA-0002, DW80J3020US/AA-0003, DW80J3020US/AA-0004, DW80J3020US/AA-0005, DW80J3020US/AA-0006, DW80J3020US/AA-0007, DW80J3020US/AA-0008, DW80J3020US/AA-0009, DW80J3020US/AA-0010, DW80J3020US/AA-0011, DW80J3020US/AA-0012, DW80J3020US/AA-0013, DW80J3020US/AA-0014
Verify your model number or contact our support team for assistance.
Key Features:
✅ Brand and Models Compatibility: Fits select Samsung dishwashers.
🔧 Specifications: High-quality plastic roller with metal axle.
💪 Reliable Performance: Ensures smooth gliding of the lower dish rack.
🛠️ Easy Installation: Tool-free; typically installed in 5–10 minutes.
🛡️ Effective Fixes: Resolves sticking, wobbling, or falling rack issues.
Product Specification
Part Number: XPARTCO DD66-00023A
Component Type: Dishwasher lower dish rack roller
Material: Plastic
Compliance: Prop 65 warning for California
Installation Notes:
Safety First: Disconnect the dishwasher from the power source before installation.
Shop for high-quality appliance parts with a 30-day return policy. Keep your dishwasher running smoothly today!
Add to cart now for a reliable fix!
WD24X10018 Dishwasher Genuine Piston & Nut Assembly
Replaces Part Numbers: WD24X10018, 821081, WD22X0133, WD22X133, WD24X0199, WD24X0220, WD24X199, WD24X220, AH260690, EA260690, AP2617344, PS260690.
Description: This Piston & Nut Assembly is a Genuine parts for specific GE dishwasher models. It plays a critical role in the dishwasher’s water management system, helping to control water flow and ensuring proper drainage during the wash cycle. You should replace this piston & nut assembly if it becomes worn out or damaged. Common causes of a bad piston & nut assembly can include mineral buildup from hard water, general wear and tear from regular use, or physical damage due to debris or foreign objects in the dishwasher.
154246801 Dishwasher Genuine OEM Sump Gasket
Description: This Dishwasher fill valve assembly is an OEM replacement part for specific Whirlpool brand dishwasher models. It is responsible for controlling the water flow into the dishwasher during the wash or rinse cycles. This part is typically located at the back or bottom of the appliance, where the water supply hoses connect. The fill valve assembly ensures that the appliance receives the correct amount of water while regulating water pressure and preventing overflow.
Replaces Part Number: 154246801, 419205, AH420465, EA420465, AP2109100, PS420465.
California Residents only
WARNING: California’s Proposition 65
10023852 Genuine OEM Bosch Dishwasher Water Valve
The 10023852 is a genuine Bosch OEM warm water inlet valve for Bosch, Thermador, Dacor, and Gaggenau dishwashers. This valve regulates the flow of warm water into the dishwasher during each wash cycle — a solenoid opens when the dishwasher calls for water and closes once the required amount has been reached, which is what prevents overfilling or underfilling and supports thorough cleaning performance.
Rated 110-127V, 60Hz. Common causes of a bad valve range from mineral buildup due to hard water, which can obstruct the valve, to general mechanical wear and electrical problems that impair the valve's ability to open or close correctly. Symptoms of a failing valve include inadequate water filling the dishwasher, overfilling that can lead to leaks and water damage, unusual noises coming from the valve area, or the dishwasher failing to start. It directly replaces 00628334, 3278459, 33199023, 628334, 9000655808, ABS12394, AP5691117, AP7193108, EAP8729241, PD00075605, PS8729241.
Quick Answer
The 10023852 Genuine OEM Bosch Dishwasher Water Valve fixes Bosch, Thermador, Dacor, and Gaggenau dishwashers with inadequate water filling, overfilling, unusual noise near the valve, or a dishwasher that won't start. 110-127V, 60Hz. Replaces 00628334, 3278459, 33199023, 628334, 9000655808, ABS12394, AP5691117, AP7193108, EAP8729241, PD00075605, PS8729241. If you're also seeing a slow leak near the sump area, be aware that on some Bosch models the sump gasket is built into the sump itself rather than sold as a separate part — a leak there is a different repair from this valve.
Common Problems This Part Fixes
Inadequate water filling the dishwasher
Overfilling, which can lead to leaks and water damage
Unusual noises coming from the valve area
Dishwasher failing to start
Poor washing results due to insufficient water supply
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This dishwasher water inlet valve directly replaces the following OEM and cross-reference part numbers:
10023852, 00628334, 3278459, 33199023, 628334, 9000655808, ABS12394, AP5691117, AP7193108, EAP8729241, PD00075605, PS8729241.
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This water inlet valve is compatible with select Bosch dishwashers, and also fits select Thermador, Dacor, and Gaggenau dishwashers built on the Bosch platform, including model numbers such as SHXM98W75N/01, SHX863WD5N/01, SHEM63W55N/01, and SHPM65Z55N/01, and spanning model series SHE, DWH, SHX, SHV, and SHP.
Note: This valve is not universal — it's designed for specific Bosch, Thermador, Dacor, and Gaggenau models. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure.
Key Features
Genuine Bosch OEM part — factory-specified solenoid design and flow rate
Regulates warm water flow into the dishwasher during each wash cycle
Resolves "won't fill properly," "overfilling," "unusual noise," and "won't start" symptoms caused by valve failure
Direct drop-in replacement — matches the original mounting and connections
Replaces 00628334, 3278459, 33199023, 628334, 9000655808, ABS12394, AP5691117, AP7193108, EAP8729241, PD00075605, PS8729241
Compatible with Bosch, Thermador, Dacor, and Gaggenau dishwashers
Genuine OEM replacement — guaranteed fit, materials, and performance
Product Specifications
Part Number
10023852
Part Type
Dishwasher Warm Water Inlet Valve
Condition
Genuine OEM
Brand
Bosch
Voltage
110-127V
Frequency
60 Hz
Function
Regulates warm water flow into the dishwasher during fill
Repair Difficulty
Easy to Moderate
Quantity
1 valve
Compatible Brands
Bosch, Thermador, Dacor, Gaggenau
Installation Notes
⚠️ Unplug Dishwasher And Shut Off Water Supply Before Starting Disconnect power at the outlet or shut off the circuit breaker, and shut off the water supply before beginning. Wear work gloves. On many Bosch models, pulling the dishwasher out from under the counter gives the best access to the valve and surrounding sump area. Photograph the wiring and hose connections before disconnecting anything. Disconnect the electrical connector and water line from the old valve, remove its mounting hardware, and pull it free. Install the new 10023852 in the same position, reconnect the water line and electrical connector fully, and secure the mounting hardware. If you're troubleshooting a slow leak in this general area rather than a fill problem, be aware that on some Bosch models the sump gasket is built directly into the sump itself and isn't sold as a separate part — a leak there is a different repair involving the sump assembly (diverter, circulation pump, drain pump, and aqua-sensor) rather than this valve. Restore the water supply and power, then run a test cycle to confirm the dishwasher fills correctly with no leaks. Tools needed: Phillips screwdriver, pliers, work gloves.
Frequently Asked Questions
My dishwasher isn't filling with enough water. Is this the right part?
Yes, this is one of the most direct symptoms of a failed water inlet valve. Since this valve is what admits warm water from your household supply into the dishwasher, mineral buildup, mechanical wear, or an electrical fault can prevent it from opening fully, leaving the dishwasher without enough water for a proper wash.
I have a slow leak near the bottom of my dishwasher. Is that this valve too?
Not necessarily. One customer traced a slow, worsening leak on a Bosch dishwasher to the sump gasket, not the water valve — and found that on their model, the gasket is built into the sump itself rather than being a separately replaceable part, requiring a more involved repair pulling the sump apart to address it. If your leak is coming specifically from the sump area rather than showing up as a fill problem, it may be a different repair than this valve replacement.
What causes this valve to fail over time?
The most common cause is mineral buildup from hard water, which can gradually obstruct the valve's internal passages. Mechanical wear and general electrical problems can also affect the valve's ability to open and close correctly over years of use.
Is this an OEM or aftermarket part?
This is a genuine OEM part, manufactured by Bosch to factory specifications — guaranteed fit, materials, and performance. It matches the original solenoid design, flow rate, and connection type of the water inlet valve originally installed in your dishwasher.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
