XPARTCO XP6974 Dryer Thermostat Kit Replaces WP3387134, WP3392519, W10900067, 279816
The XPARTCO XP6974 is an aftermarket dryer thermostat kit containing four thermal components for Whirlpool-family electric and gas dryers including Whirlpool, Kenmore, Maytag, Amana, KitchenAid, Roper, Admiral, Estate, Crosley, Inglis, and Magic Chef. The kit includes the cycling thermostat (WP3387134), thermal fuse (WP3392519), high-limit thermostat and thermal cut-off kit (279816 / W10900067) — the complete set of heat-sensing and safety components that regulate dryer temperature and prevent dangerous overheating.
These four components work together to control and protect the dryer's heating system. When any one of them fails, the dryer may produce no heat, overheat, run too long, or stop mid-cycle. Because a failed thermal fuse is almost always caused by an underlying overheating condition that also stresses the other components, replacing all four together in a single repair is the recommended approach. Includes all wiring hardware needed for installation. Installs in 20–30 minutes with basic hand tools.
Quick Answer
The XPARTCO XP6974 Dryer Thermostat Kit fixes Whirlpool-family dryers that produce no heat, overheat, take too long to dry, or stop mid-cycle. Includes all four thermal components: cycling thermostat (L155-25), thermal fuse (196°F), high-limit thermostat (L250-80), and thermal cut-off (309°F). Compatible with Whirlpool, Kenmore, Maytag, Amana, KitchenAid, Roper, Admiral, Estate, Crosley, Inglis, and Magic Chef electric and gas dryers.
Common Problems This Kit Fixes
Dryer produces no heat — thermal fuse or high-limit thermostat has blown
Dryer takes multiple cycles or very long time to dry clothes
Dryer overheats — clothes or drum too hot to touch after a cycle
Dryer shuts off mid-cycle and will not restart
Dryer tumbles normally but generates no heat at all
Dryer runs too long because cycling thermostat is not regulating temperature
Repeated thermal fuse failures — underlying thermostat fault causing recurring overheating
What's in the Kit
Part 1 of 4
WP3387134 Cycling Thermostat
Rated L155-25 · Monitors drum air temperature and cycles the heating element on and off to maintain the set drying temperature · Located on the exhaust duct or blower housing · Should show closed continuity at room temperature
Part 2 of 4
WP3392519 Thermal Fuse
Opens at 196°F (91°C) · One-time safety device located on the exhaust duct · Permanently interrupts power to the heating element if the dryer overheats · Cannot be reset — must be replaced if blown · Most common cause of no-heat in Whirlpool-family dryers
Part 3 of 4
High-Limit Thermostat (279816 / W10900067)
Rated L250-80 · Mounted on the heating element housing · Opens at approximately 250°F to cut power to the heating element if temperature exceeds safe limits · Resets automatically when it cools · Should show closed continuity at room temperature
Part 4 of 4
Thermal Cut-Off Fuse (3977393 / 279816 kit)
Opens at 309°F · Backup one-time safety device on the heating element housing · Permanently interrupts power to the heating element if the high-limit thermostat fails to open · Cannot be reset — must be replaced if blown
Replaces Part Numbers
WP3387134 Cycling Thermostat cross-references:
WP3387134, WP3387134VP, 3387134, 3387135, 3387139, 306910, 3-6910, ET187, AP6008270, PS11741405
WP3392519 Thermal Fuse cross-references:
WP3392519, WP3392519VP, 3392519, 3388651, 694511, 80005, ET401, G4AP0500, AP6008325, PS11741460
279816 High-Limit Thermostat and Thermal Cut-Off Kit cross-references:
279816, 279816VP, W10900067, 3977393, 3977767, WP3977767, WP3977767VP, 3399848, 3399693, 2651, AP3094244, AH334299, EA334299, EAP334299, PS334299
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This thermostat kit is compatible with select gas and electric dryers from the following brands:
Whirlpool dryers (gas and electric)
Kenmore / Sears dryers (Whirlpool-built models)
Maytag dryers (gas and electric)
Amana dryers
KitchenAid dryers
Roper dryers
Admiral dryers
Estate dryers
Crosley dryers
Inglis dryers
Magic Chef dryers
Important: If your thermal fuse has blown, always check for the root cause before replacing — a clogged exhaust vent is the most common cause of dryer overheating. Clean the full length of the exhaust duct before or after this repair. If the vent is clear, a failed cycling thermostat or high-limit thermostat is likely the root cause.
Key Features
Complete 4-part thermal kit — covers the cycling thermostat, thermal fuse, high-limit thermostat, and thermal cut-off in a single repair
Cycling thermostat (L155-25) — regulates drum temperature to maintain consistent, efficient drying
Thermal fuse (196°F) — one-time safety device that permanently interrupts heat if the dryer overheats
High-limit thermostat (L250-80, ~250°F) — cuts power to the heating element when temperature exceeds safe limits; auto-resets
Thermal cut-off (309°F) — backup one-time safety device protecting against heating element runaway
Replacing all four parts together ensures the complete thermal circuit is renewed — prevents recurrence if a failing thermostat caused the fuse to blow
Includes all wiring hardware for installation
Compatible with 11 major appliance brands on the Whirlpool platform
Aftermarket replacement built to OEM-equivalent quality standards
DIY repair — installs in 20–30 minutes with basic hand tools
Product Specifications
Kit Part Number
XP6974
Condition
Aftermarket Replacement
Application
Gas and Electric Dryers
Kit Includes
1x WP3387134 Cycling Thermostat, 1x WP3392519 Thermal Fuse, 1x High-Limit Thermostat (L250-80), 1x Thermal Cut-Off Fuse (309°F), wiring hardware
Cycling Thermostat Rating
L155-25 (closes at 155°F, opens at 25°F differential)
Thermal Fuse Trip Temp
196°F (91°C) — one-time, non-resettable
High-Limit Thermostat Rating
L250-80 (opens at ~250°F) — auto-resets
Thermal Cut-Off Trip Temp
309°F — one-time, non-resettable
Compatible Brands
Whirlpool, Kenmore, Maytag, Amana, KitchenAid, Roper, Admiral, Estate, Crosley, Inglis, Magic Chef
Installation Notes
⚠️ Unplug Dryer and Shut Off Gas Before Starting Disconnect power (and shut off gas for gas dryers) before beginning. Remove the back panel of the dryer to access the heating element housing and exhaust duct. The thermal fuse (WP3392519) and cycling thermostat (WP3387134) are located on the exhaust duct or blower housing — disconnect the wires, unscrew the mounting screws, and install the new parts in the same positions. The high-limit thermostat and thermal cut-off (279816 kit) are located on the heating element housing — disconnect the wires and unscrew the mounting screws to remove the old parts and install the new ones. Reconnect all wires to the correct terminals — take a photo before disconnecting to reference during reinstallation. Reassemble the back panel, restore power, and run a test cycle to verify heat. Tip: Before running the dryer, also clean the full length of the exhaust duct — a clogged vent is the most common root cause of dryer overheating and repeated thermal fuse failures. Tools needed: Phillips screwdriver, 1/4" nut driver, needle-nose pliers.
Frequently Asked Questions
What does each part in this kit do?
The cycling thermostat (WP3387134) monitors the air temperature in the exhaust duct and cycles the heating element on and off to maintain the correct drying temperature — it is the part that controls how hot the dryer gets during normal operation. The thermal fuse (WP3392519) is a one-time safety device that permanently cuts power to the heating element if the dryer overheats above 196°F — it is the most common cause of no-heat in Whirlpool-family dryers. The high-limit thermostat opens at approximately 250°F to cut heating element power if temperature gets too high, and resets automatically when it cools. The thermal cut-off is a backup one-time fuse on the heating element that opens at 309°F if the high-limit thermostat fails to protect the heater.
Why should I replace all four parts instead of just the one that failed?
When a thermal fuse blows, it almost always blew because the dryer overheated — and that overheating event put significant stress on all the other thermal components as well. A failing cycling thermostat is the most common cause of repeated thermal fuse failures: if the cycling thermostat stops regulating temperature correctly, the dryer runs too hot, the high-limit thermostat is repeatedly stressed, and the thermal fuse eventually blows. Replacing just the fuse without replacing the cycling thermostat means the same overheating will blow the new fuse. Replacing all four parts at once eliminates that risk in a single repair.
How do I test these parts with a multimeter?
Set the multimeter to continuity or resistance mode. The thermal fuse (WP3392519), cycling thermostat (WP3387134), and high-limit thermostat should all show closed continuity (near-zero resistance) at room temperature. The thermal cut-off should also show closed continuity at room temperature. Any part that reads open (no continuity / infinite resistance) at room temperature has failed and needs to be replaced. A blown thermal fuse or cut-off will always read open — they are one-time devices and cannot reset.
What causes the thermal fuse to blow repeatedly?
The most common cause by far is a clogged exhaust vent — lint accumulation inside the dryer duct restricts airflow, causing heat to build up inside the dryer cabinet until the thermal fuse trips. Always clean the full length of the exhaust duct before and after replacing these parts. Other causes include a failing cycling thermostat that is not regulating temperature correctly, a stuck heating element relay, or a dryer placed in an enclosed space without adequate ventilation.
Is this kit compatible with both electric and gas dryers?
Yes — the XP6974 kit is compatible with both electric and gas Whirlpool-family dryers. Both types use the same cycling thermostat (WP3387134) and thermal fuse (WP3392519). The high-limit thermostat and thermal cut-off (279816 kit) are located on the heating element in electric models and on the burner assembly area in gas models. Always verify your specific model number before ordering to confirm all four parts apply to your dryer.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout
XPARTCO WR17X11653 Refrigerator Dispenser Ice Door Flapper
The XPARTCO WR17X11653 is an aftermarket replacement ice door flapper, also sold as the dispenser door assembly, ice chute door or door recess assembly, for GE, Hotpoint and Kenmore side-by-side refrigerators, replacing GE part WR17X11653. It sits in the ice chute opening, seals the freezer against warm room air, and opens when the dispenser lever is pressed so ice can reach your glass.
If the door is cracked, warped, or its gasket no longer seals, warm air gets into the chute and the dispenser suffers. Check your model number before ordering, as the kit may include more than one piece.
Quick Answer
The XPARTCO WR17X11653 Ice Door Flapper replaces the ice chute door on a compatible GE, Hotpoint or Kenmore refrigerator when it is cracked, warped, or no longer seals. Classic symptoms: door sweating, frost buildup at the chute, or ice not dispensing.
Common Problems This Part Fixes
Ice dispenser door sweating
Frost buildup around the ice chute
Ice not dispensing
Cracked, warped or damaged ice door
Worn rubber gasket leaking air into the freezer
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This ice door flapper directly replaces the following part numbers:
WR17X11653, WR17X3093, WR17X3492, AGE28222, AH964304, AP3672582, EA964304, EAP964304, PD00001157, PS964304
If your old part shows a different number, contact our support team and we'll check whether it matches.
Compatibility
This ice door flapper is listed for GE, Hotpoint and Kenmore side-by-side refrigerators, including these examples:
GE TPH21PRSABB, TPH21PBSAWW, TFX20JRSBAD
GE DSE26JSEBCSS, DSF25KGTABG, DSF26DHWABB, CSK28DRBBAA
Kenmore 3639544313, 3639537713, 3639542623
Note: The models above are a small sample. One retailer lists this part for over 1,000 models. Check your full model number against your parts diagram, or contact our support team to verify fit before ordering.
Key Features
Aftermarket replacement for the GE WR17X11653 ice door flapper
Seals the ice chute opening against warm room air
Opens when the dispenser lever is pressed to release ice
Replaces a cracked, warped or leaking ice door
Product Specifications
Part Number
XPWR17X11653
OEM Part Number
WR17X11653
Part Type
Refrigerator Dispenser Ice Door Flapper
Condition
Aftermarket Replacement
Application
Select GE, Hotpoint and Kenmore Side-by-Side Refrigerators
Installation Notes
⚠️ Unplug Power Before Installing Unplug the refrigerator and move perishable food to a cooler before you begin. Wear work gloves. A Phillips screwdriver and a small flat-blade screwdriver are typically needed. No installation instructions are included with the part, so keep your model's parts diagram handy and note how the old door and any springs or pieces come apart before removing them. Install the new door the same way, then restore power and test the dispenser.
Frequently Asked Questions
What does the ice door flapper do?
It seals the ice chute opening to keep warm room air out of the freezer, and it opens when you press the dispenser lever so ice can drop into your glass.
How do I know if my ice door needs replacing?
Look for a cracked or warped door, a damaged rubber gasket, door sweating, or frost buildup around the chute. Ice that won't dispense can also point to the door.
Is this an OEM or aftermarket part?
This is an aftermarket replacement from XPARTCO, made to replace GE part WR17X11653. If you specifically need a genuine GE part, contact our support team.
Will this fit my refrigerator?
It is listed for a large number of GE, Hotpoint and Kenmore side-by-side models, but the list above is only a sample. Check your full model number against your parts diagram, or contact our support team and we'll verify it before you order.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout
12002782 Refrigerator Genuine OEM Overload Relay Kit
Replaces Part Numbers: 12002782, 1194680, 61005518, AH2004057, EA2004057, OEM12028982, AP4009659, PS2004057.
Description: This is a Genuine OEM compressor overload and relay kit for Specific Whirlpool, Maytag, Kenmore Refrigerator models. Kit was recently redesigned by manufacturer.
California Residents only
WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov
XPARTCO 62-23543-01 Gas Furnace Flame Sensor – Compatible with Rheem, Ruud, and WeatherKing Furnaces
Product Description
Restore safe and reliable furnace operation with the XPARTCO 62-23543-01 Gas Furnace Flame Sensor. This high-quality aftermarket replacement detects the presence of a burner flame and signals the control board to keep the gas valve open. A dirty or failed flame sensor can cause short cycling, ignition failure, or a furnace that won’t stay lit. Replacing it with this durable XPARTCO sensor ensures proper flame detection and dependable heating performance.
Specification :
The furnace flame sensor is designed to detect the flame.
1/4”male quick connect, Angle - sensor offset: 90 degree.
Replaces Part Numbers
62-23543-01,62-23543-02, 62-23543-03, 62-23543-04
Compatibility
This replacement flame sensor fits select Rheem, Ruud, and WeatherKing gas furnaces.
Example compatible models include (but are not limited to):Rheem RGRJ series, Ruud UGDG series, WeatherKing RGRA series.
Always verify your furnace’s model number before ordering.Contact our support team if you’re unsure.
✅ Key Features
🔄 Aftermarket Replacement – Designed to match OEM flame-sensing performance
🔥 Accurate Flame Detection – Ensures gas valve remains open only when flame is present
💰 Cost-Effective Repair – Reliable alternative to expensive OEM sensors
🛠️ Simple Installation – Direct-fit design with single mounting screw
🛡️ Fixes Common Issues – Solves furnace short cycling, ignition failure, or burner shutdown
📐 Product Specification
Part Number: 62-23543-01
Component Type: Gas Furnace Flame Sensor
Material: Stainless steel sensor rod with ceramic insulator
Mounting: Single-screw bracket mount
Electrical Connection: Spade terminal
Compliance: Built to OEM-equivalent quality standards (not OEM)
🛠️ Installation Notes
Tools Needed: Phillips screwdriver, fine abrasive pad (optional for cleaning)
⚠️ Safety First: Turn off power and gas supply to the furnace before servicing.
Steps:
Shut off furnace power and gas supply.
Locate the flame sensor near the burner assembly.
Disconnect the wire and remove the mounting screw.
Install the new XPARTCO 62-23543-01 flame sensor.
Reconnect the wire, restore power and gas, and test furnace operation.
⏱️ Time Required: 5–10 minutes
📦 Shop With Confidence
🚚 Free Shipping on All Orders
⚙️ Trusted Appliance & HVAC Parts Supplier
🔄 30-Day Return Policy
Restore safe furnace ignition and heating — Add to Cart Now for a reliable, budget-friendly replacement!
279769 Dryer Thermostat Kit - Compatible with Whirlpool, Kenmore, Maytag
Product Description
Keep your dryer running safely with the replacement 279769 Dryer Thermostat Kit. This kit is designed for select Whirlpool, Kenmore, Maytag, Roper, Estate, KitchenAid, and other dryers, featuring a high-limit thermostat (L250-80F) and a thermal cut-off fuse (352F) to prevent overheating. It addresses issues like no heat, not enough heat, overheating, or failure to start, offering a cost-effective alternative to OEM parts.
Note: Includes one high-limit thermostat, one thermal cut-off fuse. Disconnect power before installation. Check dryer venting for blockages to prevent repeat failures.
Replaces part numbers: 279769, 2004, 279548, 2796769, 279769VP, 2821, 3387812, 3389946, 3398671, 3977394, 695563, 80001, SET184, AH334278, EA334278, EAP334278, PD00002485, AP3094224, PS334278.
Compatibility:
Compatible with models including but not limited to:
Whirlpool: NGD4655EW, WGD4815EW, WGD5000DW, MGDC215EW, MGDX655DW
Kenmore: 110.60022010, 110.70102312, 110.78002012
Maytag: MEDC215EW1, MGDX655DW1
Roper: RED4640YQ0
Estate: EED4400WQ0
KitchenAid: YKEHS01PMT0
Verify your model number or contact our support team for assistance.
Key Features:
✅ Brand and Models Compatibility: Fits select Whirlpool, Kenmore, Maytag, Roper, Estate, KitchenAid, and other dryers.
🔥 Specifications: High-limit thermostat (L250-80F), thermal cut-off fuse (352F).
💰 Cost-Effective Alternative: Offers OEM-equivalent performance at a lower price.
🛠️ Easy Installation: Requires screwdriver, pliers, work gloves; typically installed in 15–20 minutes.
🛡️ Effective Fixes: Resolves no heat, not enough heat, overheating, or failure to start.
Product Specification
Part Number: 279769
Component Type: Dryer thermostat kit
Material: Metal and plastic
Dimensions: High-limit thermostat: 2" L x 1-1/2" W; Thermal cut-off fuse: 2" L x 1-1/2" W (Based on web:6, web:16)
Weight: 2.4 oz (Based on web:1, web:15)
Electrical Specs: High-limit thermostat: L250-80F (121°C); Thermal cut-off fuse: 352F (178°C)
Mounting: Screw-mounted on heater housing.
Operating Conditions: Suitable for high-heat dryer environments
Compliance: Prop 65 warning for California
Installation Notes:
Safety First: Disconnect the dryer from the power source before installation.
Shop for high-quality replacement appliance parts with a 30-day return policy. Keep your dryer running safely today!
Add to cart now for a budget-friendly fix!
WR84X10055 Genuine OEM Condenser Fan Motor
Genuine GE part. GE brands include General Electric, Hotpoint, RCA, and others.
Cross Reference Information: WR84X10055, 1093723, AH967775, EA967775, AP3797248, PS967775.
WARNING: California’s Proposition 65 (California Residents Only)
WH44X10288 Washer Lid Lock and Switch Assembly
Replaces Part Numbers: WH44X10288, 1974376, AH3496878, EA3496878, AP5270191, PS3496878.
120V, 60Hz, lid lock and switch assembly.
Fits select GE laundry center.
Description: This Door Latch Lid Lock is a replacement part for select GE washing machine models. It is designed to securely lock the washing machine's lid or door during operation, ensuring safety and preventing water from spilling during the wash cycle.
This is an aftermarket part that can be used as a replacement for the OEM part.
67006390 Refrigerator Hv Control Box
Replaces Part Numbers: WP67006390, 67006390, 12957601, 12957601SP, 4435670, AP6010509, PS11743690.
California Residents only
WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov
31001192 Genuine OEM Dryer Cycling Thermostat
Replaces Part Numbers: WP31001192, 31001192, 487706, 53-2880, AP6007590, PS11740707.
Description: This Dryer Cycling Thermostat is a Genuine OEM replacement part for Select Maytag, Kenmore, Whirlpool dryer models. It monitors internal temperatures and cycles power to the heating element accordingly. The thermostat ensures the drying air reaches and maintains the optimal heat level selected for fast, effective drying results
6601EN1003D Washer Door Lock Interlock Switch
Replaces Part Numbers: 6601EN1003D, 6601ER1005A, 2651099, AH3636296, AP5594317, EA3636296, PS3636296.
This is an aftermarket part that can be used as a replacement for the OEM part.
WARNING: California’s Proposition 65 (California Residents Only)
(8 Pack) 3977394 Dryer Thermal Cut-Off Kit – Replaces 3977394 – Compatible with Whirlpool, Kenmore, Maytag, and KitchenAid Dryers
Product Description
Protect your dryer from overheating with the 3977394 Dryer Thermal Cut-Off Kit. This high-quality aftermarket replacement shuts off the heating element if the dryer temperature rises above safe operating limits. A failed cut-off can cause no-heat issues or overheating during drying cycles. Installing this reliable 3977394 kit restores safe temperature control and helps prevent damage to internal components.
Replaces Part Numbers
XPTC352, 3977394, 352F
Compatibility
This replacement thermal cut-off kit fits select Whirlpool, Kenmore, Maytag, Roper, Estate, Crosley, and KitchenAid dryers.
Example compatible models include (but are not limited to): Whirlpool WED4815EW1, Kenmore 110.86573110, and Maytag MEDC215EW1.
Always verify your dryer’s model number before ordering. Contact our support team if you’re unsure.
✅ Key Features
🔄 Aftermarket Replacement – Matches OEM safety and temperature performance
🔥 Overheat Protection – Automatically shuts off power to the heating element if the dryer overheats
💰 Cost-Effective Fix – Affordable alternative to OEM thermal cut-off kits
🛠️ Easy Installation – Direct-fit design with included thermostats and connectors
🛡️ Fixes Common Issues – Solves dryer not heating, overheating, or shutting off prematurely
📐 Product Specification
Part Number: 3977394
Component Type: Dryer Thermal Cut-Off Kit
Includes: Thermal cut-off, high-limit thermostat, mounting hardware, and wire connectors
Temperature Rating: Cut-off opens at ~352°F.
Material: Metal thermostat housing and heat-resistant components
Compliance: Built to OEM-equivalent quality standards (not OEM)
🛠️ Installation Notes
Tools Needed: Nut driver, Phillips screwdriver
⚠️ Safety First: Always unplug the dryer before performing any repairs to prevent electrical shock.
Steps:
Disconnect power and remove the rear dryer panel.
Locate the heating element housing and identify the cut-off and thermostat.
Disconnect wires and remove the old components.
Install the new 3977394 cut-off and thermostat in the same locations.
Reconnect wires, reassemble the back panel, and restore power.
Run a short test cycle to verify proper heating.
⏱️ Time Required: 15–25 minutes
📦 Shop With Confidence
🚚 Free Shipping on All Orders
⚙️ Trusted Appliance Parts Supplier
🔄 30-Day Return Policy
Keep your dryer safe and efficient — Add to Cart Now for a reliable, budget-friendly repair!
DE92-02588G Genuine OEM Samsung Range Control Board
The DE92-02588G is a genuine Samsung OEM main control board and clock assembly for Samsung gas ranges. This board is the range's central processor for the oven side of the appliance — it monitors oven temperature, drives the heating functions, and includes the digital display that shows the time and temperature settings. Every button press on the control panel is interpreted here, and every heating command the oven executes is issued from this board.
Samsung's own service guidance draws a clear line for when this board is the correct part: order it when the range display is completely blank or unresponsive, or when the clock/timer still works but none of the oven's heating functions operate. It is specifically the wrong part when only certain buttons fail to respond or specific functions are missing while the rest of the panel works normally — that pattern points to a failed switch membrane (touchpad) instead, a separate component. Power surges, including lightning strikes near the home's electrical service, are a documented real-world cause of this board failing outright. It directly replaces AP5800586, 3553835, and PS8764724.
Quick Answer
The DE92-02588G Genuine OEM Samsung Range Control Board fixes Samsung gas ranges with a completely blank or unresponsive display, or a range where the clock/timer works but none of the oven's heating functions operate. Includes the digital clock/display. Replaces AP5800586, 3553835, PS8764724. Do NOT order this board if only certain buttons don't respond or specific functions are missing while everything else works — that points to a failed switch membrane (touchpad), not this board.
Common Problems This Part Fixes
Range display is completely blank or dead
Control panel is entirely unresponsive to any button press
Clock and timer function normally, but no oven heating functions work at all
Oven won't heat despite the range otherwise appearing to have power
SE or similar error code displayed on the control panel
Range that stopped working suddenly after a power surge or nearby lightning strike
Digital display showing incorrect or scrambled time/temperature readings
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This range control board directly replaces the following OEM and cross-reference part numbers:
DE92-02588G, AP5800586, 3553835, EAP8764724, ASM553766, PD00025599, PS8764724
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This control board is compatible with select Samsung gas ranges, including model numbers such as:
NX58F5300SS, NX58F5300SW
NX58F5500SS, NX58F5500SW, NX58F5500SB
NX58R4311SS, NX58R4311SG
Note: Before ordering, confirm your symptom matches this board specifically. If the display is blank/dead, or the clock works but heating functions don't, this board is correct. If only some buttons or functions fail while others work fine, the issue is very likely the switch membrane (touchpad) instead — a separate part from this control board. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure.
Key Features
Genuine Samsung OEM part — factory-specified processor, relay, and display circuitry
Monitors oven temperature and drives all oven heating functions
Includes the digital clock/display for time and temperature readouts
Resolves "blank display," "unresponsive control panel," and "no heating functions" symptoms caused by control board failure
Direct drop-in replacement for the original board mounting and harness connectors
Replaces AP5800586, 3553835, and PS8764724
Genuine OEM replacement — guaranteed fit, materials, and performance
Straightforward repair — typically 15 to 45 minutes with basic tools
Product Specifications
Part Number
DE92-02588G
Part Type
Range Oven Main Control Board & Clock
Condition
Genuine OEM
Brand
Samsung
Application
Gas Ranges
Function
Monitors oven temperature, drives heating functions, digital clock/display
Repair Difficulty
Easy to Moderate — 15 to 45 minutes
Quantity
1 control board
Compatible Brand
Samsung
Installation Notes
⚠️ Unplug Range Or Shut Off Breaker Before Starting — Handle The Board By Its Edges Unplug the range or shut off the house circuit breaker before beginning to avoid electrical hazards, and allow the range to cool if recently used. Wear work gloves. Access is typically through the rear of the control panel: remove the screws securing the back cover to reach the board. Photograph all harness connections before disconnecting anything — this board has multiple connectors, and getting one out of place will cause a no-start or miswired symptom. Handle the new board by its edges rather than touching the components directly, and avoid working on a carpeted surface or in conditions with static buildup, since these boards can be sensitive to static discharge. Remove the mounting screws, disconnect each harness connector from the old board, and lift it free. Install the new DE92-02588G in the same orientation, reconnect every harness connector exactly as photographed, and secure the mounting screws. Reinstall the rear cover, restore power, and test the display, clock, and all oven functions to confirm normal operation. Tools needed: Phillips screwdriver, nut driver, work gloves.
Frequently Asked Questions
Some of my buttons don't respond but others work fine. Do I need this board?
Probably not. Samsung's own guidance is specific here: if certain buttons don't respond, specific functions are missing, or you can't adjust particular settings while the rest of the panel works normally, that pattern points to a failed switch membrane (touchpad) rather than this main control board. This board is the correct part when the display is completely blank/dead, or when the clock and timer work but no heating functions operate at all.
My range stopped working right after a thunderstorm. Could that be related?
Yes, this is a documented real-world cause of this exact board failing. Power surges, including those from a nearby lightning strike, can damage the control board's circuitry outright, leading to a sudden and complete loss of function. If your range died abruptly during or shortly after a storm, this board is a strong candidate for the cause.
Should I replace the switch membrane at the same time, just in case?
Some people do replace both together, especially if they want to be certain the repair is complete on the first attempt rather than risk needing a second repair shortly after. But if your symptoms clearly match this board (blank display, or clock works with no heat) rather than the switch membrane's symptoms (some buttons unresponsive, others fine), replacing just this board is usually sufficient.
Does this board include the digital clock and display?
Yes. This is a combined control board and clock assembly — the digital display for time and temperature settings is part of this same board, not a separate component.
Is this an OEM or aftermarket part?
This is a genuine OEM part, manufactured by Samsung to factory specifications — guaranteed fit, materials, and performance. It includes the same processor, relay switching, and display circuitry as the control board originally installed in your range.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
