Search results for "microwave fuse"

XPARTCO W10900067 Dryer Thermal Cut-Off Fuse & Thermostat Kit – Compatible with Whirlpool, Maytag & Kenmore Dryers Product Description Restore safe and reliable dryer heating with the XPARTCO W10900067 Dryer Thermal Cut-Off Fuse & Thermostat Kit. This cut-off terminal is a replacement Part for specific Kenmore, Maytag, Roper, Whirlpool dryer models. The kit contains a 309°F Thermal Cut-Off Fuse and a high limit thermostat. In electric dryers, it shuts off the heat if overheating occurs to prevent fire risk. The thermal fuse cuts power while the thermostat regulates the operating temperature. To install, first, unplug the dryer. Use a multimeter to test the old fuse for continuity at room temperature; it should read zero ohms. XPARTCO is a trusted aftermarket brand offering appliance replacement parts built to OEM-equivalent specifications at a cost-effective price. Replaces Part Numbers W10900067, 4460718, N197, 197CM, 197, PD00046493, EAP11769432, AP6036100, PS11769432. Compatibility This replacement dryer thermal cut-off fuse and thermostat kit fits select Whirlpool, Maytag, Kenmore, Amana, Estate, Roper, and Crosley electric dryers. Example compatible models include (but are not limited to): Whirlpool WED4800XQ, WED4815EW1 Maytag MEDC215EW1 Kenmore 110.6012010 Always verify your dryer’s model number before ordering.Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement Kit – Matches OEM temperature and safety specifications 🌡️ Accurate Heat Protection – Helps regulate dryer temperature safely 🔥 Overheat Safety Cut-Off – Prevents damage caused by excessive heat 💰 Cost-Effective Repair – Reliable alternative to higher-priced OEM kits 🛡️ Fixes Common Issues – Resolves no heat, overheating, and thermal shutdowns 📐 Product Specification Part Number: W10900067 Component Type: Dryer Thermal Cut-Off Fuse & Thermostat Kit Includes: Thermal cut-off fuse and high-limit thermostat Application: Heater housing / exhaust temperature control Material: Heat-resistant metal housings Mounting: Screw-mounted Quality Level: Aftermarket replacement (not OEM) 🛠️ Installation Notes Tools Needed: Phillips screwdriver, nut driver ⚠️ Safety First: Always unplug the dryer before servicing to avoid electrical shock. Basic Steps: Disconnect dryer power. Remove the rear access panel. Locate the thermal cut-off and thermostat on the heater housing. Disconnect wiring and remove old components. Install the new XPARTCO W10900067 components in the same positions. Reconnect wiring, reinstall panel, and restore power. Run a test cycle to confirm proper heating. ⏱️ Time Required: 20–30 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Aftermarket Appliance Parts 🔄 30-Day Return Policy Restore safe dryer heating and protection — Add to Cart Now for a dependable, budget-friendly repair!

Read more less

XPARTCO WB02X35488 Microwave Halogen Light Bulb Product Overview The XPARTCO WB02X35488 Microwave Halogen Light Bulb provides bright interior illumination for your microwave, allowing you to clearly monitor cooking progress. Brighten your microwave with the replacement WB02X35488 Microwave Halogen Light Bulb. This high-quality Light bulb, designed for GE, Hotpoint, and Kenmore/Sears microwaves, provides clear illumination for the interior or surface below, ensuring easy monitoring of your cooking. Featuring a G8 bi-pin base (120V, 50W, 3000K warm white), this durable halogen bulb offers reliable performance and easy installation. Quick Answer If your microwave light is dim, flickering, or not working, the WB02X35488 halogen bulb may be burned out. Replacing it restores clear visibility while cooking. Replaces Part Numbers Replaces OEM part number: WB02X35488, WB08X10057, WB08X10051, WB25X25393, WB36X10292, AGE368071, PD00070655, EAP6989401, AP6989401, PS16216934. Compatibility This microwave halogen light bulb is compatible with select GE, Hotpoint, and other GE-manufactured microwaves. GE: CSA1201RSS01, CSA1201RSS02, CSA1201RSS03, CVM1790SS1SS, CVM1790SS2SS, JVM1790BK01, JVM1790CK01, JVM1790SK01, JVM1790WK01, JNM3163RJ1SS, JNM3163RJ2SS, JNM3163RJ3SS Hotpoint: Select models requiring WB08X10057 or compatible halogen bulbs Kenmore/Sears: Select models requiring WB08X10057 or compatible halogen bulbs Always verify your appliance model number before ordering. Common Problems This Part Fixes Microwave interior light not working Dim or flickering light Reduced visibility while cooking Key Features Bright halogen illumination Restores clear interior visibility High-quality aftermarket replacement Easy bulb replacement design Product Specifications Part Number: WB02X35488 Part Type: Microwave Halogen Light Bulb, 120V, 50W, G8 bi-pin base, 1.69" x 0.5", 3000K warm white, 2400 lumens, dimmable, 2000-hour average life, copper contacts. Brand: XPARTCO Condition: New OEM / Aftermarket: Aftermarket Application: Microwave Interior Lighting Troubleshooting Guide No interior light → Burned out bulb Flickering light → Failing bulb Dim light → Aging or damaged bulb When Should You Replace This Bulb? Replace this bulb if your microwave interior light is not functioning properly or has become dim or inconsistent. Installation Notes ⚠️ Disconnect power before installation. Allow the bulb to cool before handling and replace carefully according to your microwave model. Related Parts Microwave Door Switch Control Panel Turntable Motor Frequently Asked Questions Will this bulb fit my microwave?This bulb fits many GE and compatible models. Always verify your model number. Is this a halogen bulb?Yes, this is a halogen light bulb designed for microwave use. What are signs of a bad bulb?No light, dim light, or flickering indicates replacement is needed. Is installation difficult?Most bulbs are easy to replace, but always follow your appliance manual. Shop With Confidence Parts-O-Matic is a U.S.-based appliance parts retailer specializing in OEM and high-quality replacement parts. We offer fast shipping, reliable products, and expert support. Fast Shipping Quality Tested Parts Compatibility Support  

Read more less

WB06X10625CM Microwave Glass Tray Support (Ring) Rotating ring with rollers. Fits over counter GE microwaves. Replaces part Numbers: WB06X10625, SE-7000-002, AH1016203, EA1016203, AP3866954, PS1016203.   This is an aftermarket part that can be used as a replacement for the OEM part. California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

279769 Dryer Thermostat Kit - Compatible with Whirlpool, Kenmore, Maytag Product Description Keep your dryer running safely with the replacement 279769 Dryer Thermostat Kit. This kit is designed for select Whirlpool, Kenmore, Maytag, Roper, Estate, KitchenAid, and other dryers, featuring a high-limit thermostat (L250-80F) and a thermal cut-off fuse (352F) to prevent overheating. It addresses issues like no heat, not enough heat, overheating, or failure to start, offering a cost-effective alternative to OEM parts. Note: Includes one high-limit thermostat, one thermal cut-off fuse. Disconnect power before installation. Check dryer venting for blockages to prevent repeat failures. Replaces part numbers: 279769, 2004, 279548, 2796769, 279769VP, 2821, 3387812, 3389946, 3398671, 3977394, 695563, 80001, SET184, AH334278, EA334278, EAP334278, PD00002485, AP3094224, PS334278. Compatibility: Compatible with models including but not limited to: Whirlpool: NGD4655EW, WGD4815EW, WGD5000DW, MGDC215EW, MGDX655DW Kenmore: 110.60022010, 110.70102312, 110.78002012 Maytag: MEDC215EW1, MGDX655DW1 Roper: RED4640YQ0 Estate: EED4400WQ0 KitchenAid: YKEHS01PMT0 Verify your model number or contact our support team for assistance. Key Features: ✅ Brand and Models Compatibility: Fits select Whirlpool, Kenmore, Maytag, Roper, Estate, KitchenAid, and other dryers. 🔥 Specifications: High-limit thermostat (L250-80F), thermal cut-off fuse (352F). 💰 Cost-Effective Alternative: Offers OEM-equivalent performance at a lower price. 🛠️ Easy Installation: Requires screwdriver, pliers, work gloves; typically installed in 15–20 minutes. 🛡️ Effective Fixes: Resolves no heat, not enough heat, overheating, or failure to start. Product Specification Part Number: 279769 Component Type: Dryer thermostat kit Material: Metal and plastic Dimensions: High-limit thermostat: 2" L x 1-1/2" W; Thermal cut-off fuse: 2" L x 1-1/2" W (Based on web:6, web:16) Weight: 2.4 oz (Based on web:1, web:15) Electrical Specs: High-limit thermostat: L250-80F (121°C); Thermal cut-off fuse: 352F (178°C) Mounting: Screw-mounted on heater housing. Operating Conditions: Suitable for high-heat dryer environments Compliance: Prop 65 warning for California Installation Notes: Safety First: Disconnect the dryer from the power source before installation. Shop for high-quality replacement appliance parts with a 30-day return policy. Keep your dryer running safely today! Add to cart now for a budget-friendly fix!

Read more less

XPARTCO WB02X35488 (2 Pack) Microwave Halogen Light Bulb Product Overview The XPARTCO WB02X35488 Microwave Halogen Light Bulb provides bright interior illumination for your microwave, allowing you to clearly monitor cooking progress. Brighten your microwave with the replacement WB02X35488 Microwave Halogen Light Bulb. This high-quality Light bulb, designed for GE, Hotpoint, and Kenmore/Sears microwaves, provides clear illumination for the interior or surface below, ensuring easy monitoring of your cooking. Featuring a G8 bi-pin base (120V, 50W, 3000K warm white), this durable halogen bulb offers reliable performance and easy installation. Quick Answer If your microwave light is dim, flickering, or not working, the WB02X35488 halogen bulb may be burned out. Replacing it restores clear visibility while cooking. Replaces Part Numbers Replaces OEM part number: WB02X35488, WB08X10057, WB08X10051, WB25X25393, WB36X10292, AGE368071, PD00070655, EAP6989401, AP6989401, PS16216934. Compatibility This microwave halogen light bulb is compatible with select GE, Hotpoint, and other GE-manufactured microwaves. GE: CSA1201RSS01, CSA1201RSS02, CSA1201RSS03, CVM1790SS1SS, CVM1790SS2SS, JVM1790BK01, JVM1790CK01, JVM1790SK01, JVM1790WK01, JNM3163RJ1SS, JNM3163RJ2SS, JNM3163RJ3SS Hotpoint: Select models requiring WB08X10057 or compatible halogen bulbs Kenmore/Sears: Select models requiring WB08X10057 or compatible halogen bulbs Always verify your appliance model number before ordering. Common Problems This Part Fixes Microwave interior light not working Dim or flickering light Reduced visibility while cooking Key Features Bright halogen illumination Restores clear interior visibility High-quality aftermarket replacement Easy bulb replacement design Product Specifications Part Number: WB02X35488 Part Type: Microwave Halogen Light Bulb, 120V, 50W, G8 bi-pin base, 1.69" x 0.5", 3000K warm white, 2400 lumens, dimmable, 2000-hour average life, copper contacts. Brand: XPARTCO Condition: New OEM / Aftermarket: Aftermarket Application: Microwave Interior Lighting Troubleshooting Guide No interior light → Burned out bulb Flickering light → Failing bulb Dim light → Aging or damaged bulb When Should You Replace This Bulb? Replace this bulb if your microwave interior light is not functioning properly or has become dim or inconsistent. Installation Notes ⚠️ Disconnect power before installation. Allow the bulb to cool before handling and replace carefully according to your microwave model. Related Parts Microwave Door Switch Control Panel Turntable Motor Frequently Asked Questions Will this bulb fit my microwave?This bulb fits many GE and compatible models. Always verify your model number. Is this a halogen bulb?Yes, this is a halogen light bulb designed for microwave use. What are signs of a bad bulb?No light, dim light, or flickering indicates replacement is needed. Is installation difficult?Most bulbs are easy to replace, but always follow your appliance manual. Shop With Confidence Parts-O-Matic is a U.S.-based appliance parts retailer specializing in OEM and high-quality replacement parts. We offer fast shipping, reliable products, and expert support. Fast Shipping Quality Tested Parts Compatibility Support  

Read more less

XPARTCO XP6974 Dryer Thermostat Kit Replaces WP3387134, WP3392519, W10900067, 279816 The XPARTCO XP6974 is an aftermarket dryer thermostat kit containing four thermal components for Whirlpool-family electric and gas dryers including Whirlpool, Kenmore, Maytag, Amana, KitchenAid, Roper, Admiral, Estate, Crosley, Inglis, and Magic Chef. The kit includes the cycling thermostat (WP3387134), thermal fuse (WP3392519), high-limit thermostat and thermal cut-off kit (279816 / W10900067) — the complete set of heat-sensing and safety components that regulate dryer temperature and prevent dangerous overheating. These four components work together to control and protect the dryer's heating system. When any one of them fails, the dryer may produce no heat, overheat, run too long, or stop mid-cycle. Because a failed thermal fuse is almost always caused by an underlying overheating condition that also stresses the other components, replacing all four together in a single repair is the recommended approach. Includes all wiring hardware needed for installation. Installs in 20–30 minutes with basic hand tools. Quick Answer The XPARTCO XP6974 Dryer Thermostat Kit fixes Whirlpool-family dryers that produce no heat, overheat, take too long to dry, or stop mid-cycle. Includes all four thermal components: cycling thermostat (L155-25), thermal fuse (196°F), high-limit thermostat (L250-80), and thermal cut-off (309°F). Compatible with Whirlpool, Kenmore, Maytag, Amana, KitchenAid, Roper, Admiral, Estate, Crosley, Inglis, and Magic Chef electric and gas dryers. Common Problems This Kit Fixes Dryer produces no heat — thermal fuse or high-limit thermostat has blown Dryer takes multiple cycles or very long time to dry clothes Dryer overheats — clothes or drum too hot to touch after a cycle Dryer shuts off mid-cycle and will not restart Dryer tumbles normally but generates no heat at all Dryer runs too long because cycling thermostat is not regulating temperature Repeated thermal fuse failures — underlying thermostat fault causing recurring overheating What's in the Kit Part 1 of 4 WP3387134 Cycling Thermostat Rated L155-25 · Monitors drum air temperature and cycles the heating element on and off to maintain the set drying temperature · Located on the exhaust duct or blower housing · Should show closed continuity at room temperature Part 2 of 4 WP3392519 Thermal Fuse Opens at 196°F (91°C) · One-time safety device located on the exhaust duct · Permanently interrupts power to the heating element if the dryer overheats · Cannot be reset — must be replaced if blown · Most common cause of no-heat in Whirlpool-family dryers Part 3 of 4 High-Limit Thermostat (279816 / W10900067) Rated L250-80 · Mounted on the heating element housing · Opens at approximately 250°F to cut power to the heating element if temperature exceeds safe limits · Resets automatically when it cools · Should show closed continuity at room temperature Part 4 of 4 Thermal Cut-Off Fuse (3977393 / 279816 kit) Opens at 309°F · Backup one-time safety device on the heating element housing · Permanently interrupts power to the heating element if the high-limit thermostat fails to open · Cannot be reset — must be replaced if blown Replaces Part Numbers WP3387134 Cycling Thermostat cross-references: WP3387134, WP3387134VP, 3387134, 3387135, 3387139, 306910, 3-6910, ET187, AP6008270, PS11741405 WP3392519 Thermal Fuse cross-references: WP3392519, WP3392519VP, 3392519, 3388651, 694511, 80005, ET401, G4AP0500, AP6008325, PS11741460 279816 High-Limit Thermostat and Thermal Cut-Off Kit cross-references: 279816, 279816VP, W10900067, 3977393, 3977767, WP3977767, WP3977767VP, 3399848, 3399693, 2651, AP3094244, AH334299, EA334299, EAP334299, PS334299 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This thermostat kit is compatible with select gas and electric dryers from the following brands: Whirlpool dryers (gas and electric) Kenmore / Sears dryers (Whirlpool-built models) Maytag dryers (gas and electric) Amana dryers KitchenAid dryers Roper dryers Admiral dryers Estate dryers Crosley dryers Inglis dryers Magic Chef dryers Important: If your thermal fuse has blown, always check for the root cause before replacing — a clogged exhaust vent is the most common cause of dryer overheating. Clean the full length of the exhaust duct before or after this repair. If the vent is clear, a failed cycling thermostat or high-limit thermostat is likely the root cause. Key Features Complete 4-part thermal kit — covers the cycling thermostat, thermal fuse, high-limit thermostat, and thermal cut-off in a single repair Cycling thermostat (L155-25) — regulates drum temperature to maintain consistent, efficient drying Thermal fuse (196°F) — one-time safety device that permanently interrupts heat if the dryer overheats High-limit thermostat (L250-80, ~250°F) — cuts power to the heating element when temperature exceeds safe limits; auto-resets Thermal cut-off (309°F) — backup one-time safety device protecting against heating element runaway Replacing all four parts together ensures the complete thermal circuit is renewed — prevents recurrence if a failing thermostat caused the fuse to blow Includes all wiring hardware for installation Compatible with 11 major appliance brands on the Whirlpool platform Aftermarket replacement built to OEM-equivalent quality standards DIY repair — installs in 20–30 minutes with basic hand tools Product Specifications Kit Part Number XP6974 Condition Aftermarket Replacement Application Gas and Electric Dryers Kit Includes 1x WP3387134 Cycling Thermostat, 1x WP3392519 Thermal Fuse, 1x High-Limit Thermostat (L250-80), 1x Thermal Cut-Off Fuse (309°F), wiring hardware Cycling Thermostat Rating L155-25 (closes at 155°F, opens at 25°F differential) Thermal Fuse Trip Temp 196°F (91°C) — one-time, non-resettable High-Limit Thermostat Rating L250-80 (opens at ~250°F) — auto-resets Thermal Cut-Off Trip Temp 309°F — one-time, non-resettable Compatible Brands Whirlpool, Kenmore, Maytag, Amana, KitchenAid, Roper, Admiral, Estate, Crosley, Inglis, Magic Chef Installation Notes ⚠️ Unplug Dryer and Shut Off Gas Before Starting Disconnect power (and shut off gas for gas dryers) before beginning. Remove the back panel of the dryer to access the heating element housing and exhaust duct. The thermal fuse (WP3392519) and cycling thermostat (WP3387134) are located on the exhaust duct or blower housing — disconnect the wires, unscrew the mounting screws, and install the new parts in the same positions. The high-limit thermostat and thermal cut-off (279816 kit) are located on the heating element housing — disconnect the wires and unscrew the mounting screws to remove the old parts and install the new ones. Reconnect all wires to the correct terminals — take a photo before disconnecting to reference during reinstallation. Reassemble the back panel, restore power, and run a test cycle to verify heat. Tip: Before running the dryer, also clean the full length of the exhaust duct — a clogged vent is the most common root cause of dryer overheating and repeated thermal fuse failures. Tools needed: Phillips screwdriver, 1/4" nut driver, needle-nose pliers. Frequently Asked Questions What does each part in this kit do? The cycling thermostat (WP3387134) monitors the air temperature in the exhaust duct and cycles the heating element on and off to maintain the correct drying temperature — it is the part that controls how hot the dryer gets during normal operation. The thermal fuse (WP3392519) is a one-time safety device that permanently cuts power to the heating element if the dryer overheats above 196°F — it is the most common cause of no-heat in Whirlpool-family dryers. The high-limit thermostat opens at approximately 250°F to cut heating element power if temperature gets too high, and resets automatically when it cools. The thermal cut-off is a backup one-time fuse on the heating element that opens at 309°F if the high-limit thermostat fails to protect the heater. Why should I replace all four parts instead of just the one that failed? When a thermal fuse blows, it almost always blew because the dryer overheated — and that overheating event put significant stress on all the other thermal components as well. A failing cycling thermostat is the most common cause of repeated thermal fuse failures: if the cycling thermostat stops regulating temperature correctly, the dryer runs too hot, the high-limit thermostat is repeatedly stressed, and the thermal fuse eventually blows. Replacing just the fuse without replacing the cycling thermostat means the same overheating will blow the new fuse. Replacing all four parts at once eliminates that risk in a single repair. How do I test these parts with a multimeter? Set the multimeter to continuity or resistance mode. The thermal fuse (WP3392519), cycling thermostat (WP3387134), and high-limit thermostat should all show closed continuity (near-zero resistance) at room temperature. The thermal cut-off should also show closed continuity at room temperature. Any part that reads open (no continuity / infinite resistance) at room temperature has failed and needs to be replaced. A blown thermal fuse or cut-off will always read open — they are one-time devices and cannot reset. What causes the thermal fuse to blow repeatedly? The most common cause by far is a clogged exhaust vent — lint accumulation inside the dryer duct restricts airflow, causing heat to build up inside the dryer cabinet until the thermal fuse trips. Always clean the full length of the exhaust duct before and after replacing these parts. Other causes include a failing cycling thermostat that is not regulating temperature correctly, a stuck heating element relay, or a dryer placed in an enclosed space without adequate ventilation. Is this kit compatible with both electric and gas dryers? Yes — the XP6974 kit is compatible with both electric and gas Whirlpool-family dryers. Both types use the same cycling thermostat (WP3387134) and thermal fuse (WP3392519). The high-limit thermostat and thermal cut-off (279816 kit) are located on the heating element in electric models and on the burner assembly area in gas models. Always verify your specific model number before ordering to confirm all four parts apply to your dryer. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO 50561602 Heater Safety Thermostat  Compatible with Victory 50561602 Safety Switch, Heater, 250F

Read more less

XPARTCO 6931EL3002M Dryer Blower Thermostat – Compatible with LG and Kenmore Dryers Product Description Restore proper temperature regulation in your dryer with the XPARTCO 6931EL3002M Dryer Blower Thermostat. This Dryer Blower Thermostat is a replacement part for select LG dryer models. It plays a role in regulating the operation of the blower motor, which is responsible for circulating hot air throughout the dryer during the drying cycle. Common causes of a bad dryer blower thermostat can include electrical malfunctions, physical damage, or simply wear and tear over time.  Replaces Part Numbers 6931EL3002M, 6931EL3002A, 6931EL3002K, PD00023476, EAP8747887, AP5782317, PS8747887. Compatibility This replacement blower thermostat (mounts on blower housing). fits select LG and Kenmore (manufactured by LG) dryers. Example compatible models include (but are not limited to):LG DLE5977W, DLE3170W, DLEX3470V, and Kenmore 796.81022900. Always verify your dryer’s model number before ordering. Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement – Matches OEM temperature control performance 🌡️ Accurate Temperature Regulation – Maintains proper blower housing heat levels. Thermostat 85C, 185F. 💰 Budget-Friendly Option – Provides OEM-level reliability at a lower price 🛠️ Easy Installation – Direct-fit design with standard mounting hardware 🛡️ Fixes Common Issues – Solves overheating, no-heat problems, long dry times, and auto-shutoff issues 📐 Product Specification Part Number: 6931EL3002M Component Type: Dryer Blower Thermostat Material: Metal thermostat housing with bimetal sensor Temperature Rating: Opens/closes at OEM-equivalent temperature thresholds Mounting: Two-screw mounting to blower housing Compliance: Built to OEM-equivalent quality standards (not OEM) 🛠️ Installation Notes Tools Needed: Phillips screwdriver, nut driver ⚠️ Safety First: Always unplug the dryer before performing repairs to prevent electrical shock and injury. Steps: Disconnect power and remove the dryer’s rear access panel. Locate the blower housing and identify the thermostat. Remove the mounting screws and disconnect the wiring. Install the new XPARTCO 6931EL3002M thermostat in the same position. Reconnect wires, reinstall the panel, and restore power. Run a test cycle to confirm proper temperature cycling. ⏱️ Time Required: 10–15 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Appliance Parts Supplier 🔄 30-Day Return Policy Restore safe temperature control — Add to Cart Now for a reliable, cost-effective repair!

Read more less

XP53-0771 Dryer Thermostat This thermostat has a limit of 248°F. It will turn the heating element back on when the temperature drops by 80°F. Fits Maytag, Admiral, Norge Electric Dryers Replaces Part Numbers:WP53-0771, 53-0771, 53-0306, 53-1037, 53-1459, ER53-0771, OEM18028919, AP6009638, PS11742806, SET176, TJSET176.   This is an aftermarket part that can be used as a replacement for the OEM part. California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

WE4X800 Dryer Genuine OEM Thermostat Replaces Part Numbers: WE4X800, 2285, AH268245, EA268245, ET800, WE04X0730, WE04X0800, WE4X730, OEM10477750, AP2619437, PS268245. Description: This Thermal Cut-Off Kit is a Genuine OEM part for specific GE dryer models. This safety kit is designed to protect the dryer from overheating by interrupting the heat source when the dryer air temperature reaches dangerously high levels.    California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

XPARTCO 35001087 Dryer Thermal Cut Off - Compatible with Samsung, Kenmore, Maytag Dryers Product Description Safeguard your dryer with the replacement XPARTCO 35001087 Dryer Thermal Cut Off. This thermal cut-off fuse is designed for select Samsung, Kenmore, and Maytag dryers, shutting off the heating element or burner when the dryer overheats to prevent fires or damage. It addresses issues like no heat, failure to start, or premature shutoff, offering a cost-effective alternative to OEM parts. Note: Includes one thermal cut-off fuse with two 1/4" male spade terminals. Disconnect power before installation. Replaces part numbers: WP35001087, 35001087, 1122480, PD00003747, EAP11741821, AP6008681, PS11741821.  Compatibility: Compatible with models including but not limited to: Samsung: DV203AES, DV209AEW/XAA-0000, DV210AEW/XAA, DV42H5000EW/A3, DV45H7000EW/A2, DV48H7400EW/A2 Kenmore: 40289032010, 40289032011, 40299032010, 40299032012 Maytag: MDE3000AYW, MEDB200VQ0, MEDB850WB0 Verify your model number or contact our support team for assistance. Key Features: ✅ Brand and Models Compatibility: Fits select Samsung, Kenmore, Maytag, Amana, and Inglis dryers. 🔥 Specifications: replacement thermal cut-off fuse, opens at 185°F (85°C), 25A at 125/250VAC. 💰 Cost-Effective Alternative: Offers OEM-equivalent performance at a lower price. 🛠️ Easy Installation: Requires Phillips screwdriver, pliers, work gloves; typically installed in 15–20 minutes. 🛡️ Effective Fixes: Resolves no heat, failure to start, or premature shutoff due to overheating. Product Specification Part Number: XPARTCO 35001087 Component Type: Thermal cut-off fuse Material: Plastic and metal Electrical Specs: 25A at 125/250VAC, opens at 185°F (85°C) Mounting: Two 1/4" male spade terminals, 1" between mounting holes (center to center) Operating Conditions: Suitable for high-temperature dryer environments Compliance: UL-listed components, Prop 65 warning for California Installation Notes: Safety First: Disconnect the dryer from the power source before installation. Shop for high-quality replacement appliance parts with a 30-day return policy. Keep your dryer safe and operational today! Add to cart now for a budget-friendly fix!

Read more less

XPARTCO 8557403 Dryer High-Limit Thermostat with Thermistor Replaces WP8557403 The XPARTCO 8557403 is an aftermarket replacement dryer high-limit thermostat and thermistor sensor assembly compatible with a wide range of Whirlpool, Maytag, Kenmore, Amana, KitchenAid, Jenn-Air, Roper, Admiral, Norge, and Magic Chef electric dryers — including the Whirlpool Duet and Maytag MED series. This single component combines two functions: the high-limit thermostat (rated L146-44C, opens at 295°F) acts as a resettable safety switch that cuts power to the heating element if the dryer air temperature exceeds safe limits, and the integrated 50-ohm thermistor continuously monitors air temperature and sends resistance-based readings to the control board to regulate the drying cycle. When this part fails — whether the thermostat opens permanently or the thermistor provides incorrect temperature data — the dryer may produce no heat, run too hot, take too long to dry, overheat, or display temperature-related error codes. It measures 1-5/8"L x 1-5/8"W x 2"H with approximately 1-5/8" between mounting holes and is constructed from black/gray plastic and metal. It directly replaces WP8557403, 1180102, AP6013164, EAP11746386, PD00003588, and PS11746386. Note: the exhaust duct thermostat and thermal fuse are separate parts — if those have also failed, they must be ordered separately. Installs in 15–20 minutes with basic hand tools. Quick Answer The XPARTCO 8557403 Dryer High-Limit Thermostat with Thermistor fixes Whirlpool Duet, Maytag MED, and related dryers with no heat, overheating, or erratic temperature. Combined part: L146-44C high-limit thermostat (opens at 295°F, auto-resets) + 50-ohm NTC thermistor. 1-5/8"L x 1-5/8"W x 2"H, ~1-5/8" between mounting holes. Replaces WP8557403, 1180102, AP6013164, EAP11746386, PD00003588, PS11746386. For Whirlpool, Maytag, Kenmore, Amana, KitchenAid, Jenn-Air, Roper, and Admiral electric dryers. Common Problems This Part Fixes Dryer produces no heat — high-limit thermostat has failed open Dryer overheating — thermostat not opening at the correct temperature Dryer takes too long to dry — thermistor providing incorrect temperature readings to the control board Dryer cycling on and off erratically — thermistor fault causing incorrect cycle control Temperature-related error codes on models with digital displays Multimeter test shows open circuit on the thermostat at room temperature Multimeter test shows open or shorted thermistor (not ~50 ohms at room temperature) Replaces Part Numbers This thermostat/thermistor assembly directly replaces the following OEM and cross-reference part numbers: WP8557403, 8557403, 1180102, AP6013164, AWP48681, EAP11746386, PD00003588, PS11746386. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This high-limit thermostat and thermistor is compatible with select electric dryers only from the following brands: Whirlpool electric dryers — Duet, WED5000, WED5500, WED5600, WED5620, WED8000, WED8200, WED8500, WED9200, WED92HEF, WED7000 series and related models Maytag electric dryers — MED3500, MED5630, MED6630, MED7230, MEDB835 series and related models Kenmore / Sears electric dryers — 110-series (Whirlpool-built models) Amana electric dryers (select models) KitchenAid electric dryers (select models) Jenn-Air electric dryers (select models) Roper electric dryers Admiral electric dryers Norge electric dryers Magic Chef electric dryers Note: This part is for electric dryers only. The exhaust duct thermal fuse and cycling thermostat are separate parts — if those have also failed, they must be ordered separately. Always verify your model number before ordering. Key Features Combined high-limit thermostat and thermistor in a single assembly — replaces both functions in one part High-limit thermostat rated L146-44C — opens at 295°F (146°C), resets automatically when cooled Integrated 50-ohm NTC thermistor — continuously monitors dryer air temperature and sends readings to the control board for cycle regulation Dimensions: 1-5/8"L x 1-5/8"W x 2"H; approx. 1-5/8" between mounting holes Black/gray plastic and metal construction Electric dryers only — not for gas dryer models Replaces WP8557403, 1180102, AP6013164, EAP11746386, PD00003588, and PS11746386 Compatible with Whirlpool Duet, Maytag MED, Kenmore, Amana, KitchenAid, Jenn-Air, Roper, Admiral, Norge, and Magic Chef electric dryers Aftermarket replacement built to OEM-equivalent quality standards Quick DIY repair — installs in 15–20 minutes with basic hand tools Product Specifications Part Number 8557403 OEM Part Number WP8557403 Part Type Dryer High-Limit Thermostat with Integrated Thermistor Sensor Condition Aftermarket Replacement Application Electric Dryers Only Thermostat Rating L146-44C — opens at 295°F (146°C), auto-resets Thermistor 50-ohm NTC (at room temperature ~25°C) Dimensions 1-5/8"L x 1-5/8"W x 2"H Mounting Hole Spacing Approx. 1-5/8" center to center Color Black / Gray Material Plastic / Metal Compatible Brands Whirlpool, Maytag, Kenmore, Amana, KitchenAid, Jenn-Air, Roper, Admiral, Norge, Magic Chef Installation Notes ⚠️ Unplug Dryer Before Starting — Electric Dryers Only Disconnect power before beginning. The 8557403 thermostat/thermistor assembly is typically located on the heating element housing or duct inside the dryer — access it by removing the back panel. On Whirlpool Duet and Maytag front-load-style dryers, the component may be accessible by removing the lower front panel. Photograph all wire connections before disconnecting — the thermistor wires and thermostat wires must be reconnected to the correct terminals. Remove the two mounting screws and pull the old assembly off. Note the position and orientation before removing. Install the new 8557403 assembly in the same position and orientation, reconnect all wires, and reinstall the mounting screws and panel. Restore power and run a test heat cycle to confirm normal operation. Tools needed: Phillips screwdriver, 1/4" nut driver. Frequently Asked Questions What makes this part unusual — why does it combine a thermostat and a thermistor? The WP8557403 is a combined assembly used on newer Whirlpool Duet and Maytag MED series dryers that use electronic temperature control rather than purely mechanical thermostats. The high-limit thermostat (L146-44C) provides the traditional safety function — it opens the circuit if dryer temperature exceeds 295°F. The integrated NTC thermistor continuously reports resistance-based temperature data to the electronic control board, which uses the data to regulate the heating element and control cycle timing. Both functions are built into a single compact housing, making this a unique part that replaces what older dryers used to handle with separate components. How do I test the thermostat and thermistor? Set your multimeter to continuity or resistance mode. For the thermostat portion: probe the thermostat terminals — at room temperature, a working thermostat shows closed continuity (near-zero resistance). An open circuit at room temperature confirms the thermostat has failed. For the thermistor portion: probe the thermistor terminals — at room temperature (approximately 25°C/77°F), a working 50-ohm NTC thermistor should read approximately 50 ohms. A reading of zero ohms (shorted) or open circuit (no continuity) confirms the thermistor has failed. Either failure mode warrants replacing the complete 8557403 assembly. What is the difference between 8557403 and WP8557403? These are the same part. WP8557403 is the updated Whirlpool OEM part number that superseded the original 8557403. The 1180102 is also a cross-reference for this same assembly. This aftermarket replacement is compatible with all of these numbers. Do I also need to replace the thermal fuse or cycling thermostat? The 8557403 replaces the high-limit thermostat and thermistor mounted on the heating element housing area. The exhaust duct thermal fuse (WP3392519 on most Whirlpool-family dryers) and cycling thermostat (WP3387134) are separate components located on the exhaust duct and are not included in or replaced by the 8557403. If your dryer has no heat, test all thermal components before ordering — check the 8557403 assembly, the thermal fuse, and the cycling thermostat, then order only what has failed. If an overheating event caused the high-limit to fail, the other thermal components may be stressed as well. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured from plastic and metal with an L146-44C thermostat and 50-ohm NTC thermistor to match the specifications and performance of the original WP8557403 assembly. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less