Search results for "microwave switch"

5304517587 Dishwasher Switch Assembly Description:  The Switch Assembly is an OEM replacement part for specific Frigidaire dishwasher models. It contains a touchpad and electronic controls that operate wash cycles and drying features.  Replaces Part Numbers:5304517587, 4840235, AP6802340, PS12585690.  California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

XPARTCO 3406105 Dryer Door Switch Replaces WP3406105 The XPARTCO 3406105 is an aftermarket replacement dryer door switch assembly compatible with a wide range of Whirlpool-family dryers including Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Roper, Estate, Crosley, Inglis, Admiral, Jenn-Air, Magic Chef, and Norge. The door switch is a safety component mounted inside the dryer cabinet near the door opening. When the door is closed, the door strike depresses the switch actuator, completing the circuit and allowing the dryer to start and run. When the door is opened, the switch opens the circuit and stops the dryer. On models with a broken belt detection circuit, the door switch also plays a role in belt failure detection. A failed door switch causes the dryer to either not start at all or to run continuously with the door open. This is a Single Pole, Double Throw (SPDT) 3-wire switch with stainless steel terminals and a heat-resistant housing. It measures 1-3/4" L x 1-5/8" W x 1-1/4" H with a 7-3/4" wiring harness. Electrical specs are 120-240V, 50-60Hz, 11A, 1/3HP. The kit includes the switch and 3-wire harness assembly. It directly replaces WP3406105, 3406104, 3405104, 3405105, 528947, AP6008560, and several additional cross-reference numbers. Installs in 15–30 minutes with basic hand tools. Quick Answer The XPARTCO 3406105 Dryer Door Switch fixes Whirlpool-family dryers that won't start, won't stop when the door is opened, or require the door to be slammed to start. SPDT 3-wire switch, 120-240V/50-60Hz/11A/1/3HP. Body 1-3/4" L x 1-5/8" W x 1-1/4" H, 7-3/4" harness. Includes switch and harness assembly. Compatible with Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Roper, and more. Replaces WP3406105, 3406104, 3405104, 528947, AP6008560. Common Problems This Part Fixes Dryer will not start at all — door switch not completing the circuit when door is closed Dryer starts only when the door is slammed or held firmly closed Dryer continues to run after the door is opened — switch not opening the circuit Drum light not turning on when the door is opened (on models with drum light) Dryer starts intermittently — door switch contact worn and making unreliable contact Dryer stops mid-cycle randomly — switch opening the circuit due to vibration or wear Door switch visibly cracked, broken, or the actuator button no longer springs back Replaces Part Numbers This door switch directly replaces the following OEM and cross-reference part numbers: WP3406105, 3405104, 3405105, 3406104, 3406105, WP3406105VP, AWP47182, PD00003898, EAP11741700, AP6008560, PS11741700. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This door switch is compatible with select gas and electric dryers from the following brands: Whirlpool dryers (gas and electric) Kenmore / Sears dryers (Whirlpool-built models) Maytag dryers (gas and electric) KitchenAid dryers Amana dryers Roper dryers Estate dryers Crosley dryers Inglis dryers Admiral dryers Jenn-Air dryers Magic Chef dryers Norge dryers Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Safety switch — prevents dryer from operating when the door is open and stops the dryer immediately when the door is opened mid-cycle Single Pole, Double Throw (SPDT) 3-wire switch — provides both normally-open and normally-closed contacts for dryer start circuit and belt failure detection on compatible models Rated 120-240V, 50-60Hz, 11A, 1/3HP — correct electrical specifications for compatible Whirlpool-family dryers Switch body: 1-3/4" L x 1-5/8" W x 1-1/4" H; wiring harness: 7-3/4" L Stainless steel terminals and heat-resistant housing Kit includes switch and 3-wire harness assembly — complete plug-in replacement Replaces WP3406105, 3406104, 3405104, 3405105, 528947, and AP6008560 Compatible with 13 major appliance brands on the Whirlpool platform Aftermarket replacement built to OEM-equivalent quality standards Quick DIY repair — installs in 15–30 minutes with basic hand tools Product Specifications Part Number 3406105 OEM Part Number WP3406105 Part Type Dryer Door Switch Assembly (SPDT 3-Wire) Condition Aftermarket Replacement Application Gas and Electric Dryers Switch Type Single Pole, Double Throw (SPDT) Wires 3-wire Voltage 120-240V Frequency 50-60Hz Amperage 11A Horsepower 1/3 HP Switch Body Dimensions 1-3/4" L x 1-5/8" W x 1-1/4" H Harness Length 7-3/4 inches Color Off-White / Black / Gray Material Plastic / Metal (stainless steel terminals) Includes Switch and 3-wire harness assembly Compatible Brands Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Roper, Estate, Crosley, Inglis, Admiral, Jenn-Air, Magic Chef, Norge Installation Notes ⚠️ Unplug Dryer Before Starting Disconnect power (and shut off gas for gas dryers) before beginning. The door switch is located inside the dryer cabinet near the door opening, typically mounted in the front panel or top panel. Access it by inserting a putty knife under the top panel to release the spring clips and lift the top, then release the front panel. Locate the old door switch — it is a small rectangular component with a spring-loaded actuator button. Photograph the wiring connections before disconnecting. Disconnect the 3-wire harness from the old switch. Release the switch from its mounting bracket by pressing the retaining tabs and pulling the switch free, or unscrewing the mounting screw. Snap the new 3406105 switch into the mounting bracket and reconnect the 3-wire harness in the same positions. Reassemble the front and top panels, restore power, and run a test cycle to confirm the dryer starts, stops when the door is opened, and runs normally. Tools needed: Phillips screwdriver, putty knife. Frequently Asked Questions What does the dryer door switch do? The door switch is a safety component that monitors whether the dryer door is open or closed. When the door is closed, the door strike depresses the switch actuator, completing the electrical circuit and signaling the control board that it is safe to run. When the door is opened, the actuator releases, opening the circuit and stopping the dryer immediately. On many Whirlpool-family dryers, the 3-wire SPDT switch also provides a secondary circuit used for broken belt detection — one of the switch's contacts is part of the motor start circuit, while the other is part of a safety cutoff circuit. How do I test the door switch with a multimeter? Unplug the dryer and disconnect the switch from the harness. Set your multimeter to continuity mode. The 3406105 is an SPDT switch with three terminals — typically labeled Common (C), Normally Open (NO), and Normally Closed (NC). With the actuator button not pressed (door open position), you should read continuity between C and NC, and no continuity between C and NO. With the actuator button pressed (door closed position), you should read continuity between C and NO, and no continuity between C and NC. Any deviation from this pattern confirms the switch has failed. What is the difference between 3406105 and 3406104? The 3406104 was the original part number, and the 3406105 (later updated to WP3406105) is the current replacement that superseded it. They are the same door switch and are fully interchangeable. The 3405104 and 3405105 are also cross-references for this same switch from earlier production. If your dryer's documentation or old switch label shows any of these numbers, the 3406105 is the correct current replacement. Why does this switch have 3 wires when my old switch only had 2? The WP3406105 is an SPDT (Single Pole, Double Throw) switch with 3 terminals — Common, Normally Open, and Normally Closed. Some older dryer models used a simpler 2-wire switch, but the 3-wire WP3406105 is the updated replacement that works on both older and newer models. On models that originally had a 2-wire switch, only two of the three terminals are used — the third is simply left unconnected. Follow your model's wiring diagram or take a photo of the original switch's wire connections before removing it. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured from durable plastic and metal with stainless steel terminals to match the dimensions and electrical specifications of the original WP3406105 door switch assembly. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

DE92-02588G Genuine OEM Samsung Range Control Board The DE92-02588G is a genuine Samsung OEM main control board and clock assembly for Samsung gas ranges. This board is the range's central processor for the oven side of the appliance — it monitors oven temperature, drives the heating functions, and includes the digital display that shows the time and temperature settings. Every button press on the control panel is interpreted here, and every heating command the oven executes is issued from this board. Samsung's own service guidance draws a clear line for when this board is the correct part: order it when the range display is completely blank or unresponsive, or when the clock/timer still works but none of the oven's heating functions operate. It is specifically the wrong part when only certain buttons fail to respond or specific functions are missing while the rest of the panel works normally — that pattern points to a failed switch membrane (touchpad) instead, a separate component. Power surges, including lightning strikes near the home's electrical service, are a documented real-world cause of this board failing outright. It directly replaces AP5800586, 3553835, and PS8764724. Quick Answer The DE92-02588G Genuine OEM Samsung Range Control Board fixes Samsung gas ranges with a completely blank or unresponsive display, or a range where the clock/timer works but none of the oven's heating functions operate. Includes the digital clock/display. Replaces AP5800586, 3553835, PS8764724. Do NOT order this board if only certain buttons don't respond or specific functions are missing while everything else works — that points to a failed switch membrane (touchpad), not this board. Common Problems This Part Fixes Range display is completely blank or dead Control panel is entirely unresponsive to any button press Clock and timer function normally, but no oven heating functions work at all Oven won't heat despite the range otherwise appearing to have power SE or similar error code displayed on the control panel Range that stopped working suddenly after a power surge or nearby lightning strike Digital display showing incorrect or scrambled time/temperature readings Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This range control board directly replaces the following OEM and cross-reference part numbers: DE92-02588G, AP5800586, 3553835, EAP8764724, ASM553766, PD00025599, PS8764724 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This control board is compatible with select Samsung gas ranges, including model numbers such as: NX58F5300SS, NX58F5300SW NX58F5500SS, NX58F5500SW, NX58F5500SB NX58R4311SS, NX58R4311SG Note: Before ordering, confirm your symptom matches this board specifically. If the display is blank/dead, or the clock works but heating functions don't, this board is correct. If only some buttons or functions fail while others work fine, the issue is very likely the switch membrane (touchpad) instead — a separate part from this control board. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Genuine Samsung OEM part — factory-specified processor, relay, and display circuitry Monitors oven temperature and drives all oven heating functions Includes the digital clock/display for time and temperature readouts Resolves "blank display," "unresponsive control panel," and "no heating functions" symptoms caused by control board failure Direct drop-in replacement for the original board mounting and harness connectors Replaces AP5800586, 3553835, and PS8764724 Genuine OEM replacement — guaranteed fit, materials, and performance Straightforward repair — typically 15 to 45 minutes with basic tools Product Specifications Part Number DE92-02588G Part Type Range Oven Main Control Board & Clock Condition Genuine OEM Brand Samsung Application Gas Ranges Function Monitors oven temperature, drives heating functions, digital clock/display Repair Difficulty Easy to Moderate — 15 to 45 minutes Quantity 1 control board Compatible Brand Samsung Installation Notes ⚠️ Unplug Range Or Shut Off Breaker Before Starting — Handle The Board By Its Edges Unplug the range or shut off the house circuit breaker before beginning to avoid electrical hazards, and allow the range to cool if recently used. Wear work gloves. Access is typically through the rear of the control panel: remove the screws securing the back cover to reach the board. Photograph all harness connections before disconnecting anything — this board has multiple connectors, and getting one out of place will cause a no-start or miswired symptom. Handle the new board by its edges rather than touching the components directly, and avoid working on a carpeted surface or in conditions with static buildup, since these boards can be sensitive to static discharge. Remove the mounting screws, disconnect each harness connector from the old board, and lift it free. Install the new DE92-02588G in the same orientation, reconnect every harness connector exactly as photographed, and secure the mounting screws. Reinstall the rear cover, restore power, and test the display, clock, and all oven functions to confirm normal operation. Tools needed: Phillips screwdriver, nut driver, work gloves. Frequently Asked Questions Some of my buttons don't respond but others work fine. Do I need this board? Probably not. Samsung's own guidance is specific here: if certain buttons don't respond, specific functions are missing, or you can't adjust particular settings while the rest of the panel works normally, that pattern points to a failed switch membrane (touchpad) rather than this main control board. This board is the correct part when the display is completely blank/dead, or when the clock and timer work but no heating functions operate at all. My range stopped working right after a thunderstorm. Could that be related? Yes, this is a documented real-world cause of this exact board failing. Power surges, including those from a nearby lightning strike, can damage the control board's circuitry outright, leading to a sudden and complete loss of function. If your range died abruptly during or shortly after a storm, this board is a strong candidate for the cause. Should I replace the switch membrane at the same time, just in case? Some people do replace both together, especially if they want to be certain the repair is complete on the first attempt rather than risk needing a second repair shortly after. But if your symptoms clearly match this board (blank display, or clock works with no heat) rather than the switch membrane's symptoms (some buttons unresponsive, others fine), replacing just this board is usually sufficient. Does this board include the digital clock and display? Yes. This is a combined control board and clock assembly — the digital display for time and temperature settings is part of this same board, not a separate component. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by Samsung to factory specifications — guaranteed fit, materials, and performance. It includes the same processor, relay switching, and display circuitry as the control board originally installed in your range. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

WD21X10367 Dishwasher Genuine Module Control Asm Replaces Part Numbers: WD21X10367, WD21X10269, AH2344315, EA2344315, AP4367159, PS2344315.

Read more less

DC34-00025G Washer Genuine OEM Lid Switch and Lock Assembly – Fits Samsung Washers Product Overview The DC34-00025G Washer Lid Switch and Lock Assembly is a genuine OEM replacement part that ensures your washer lid stays securely locked during wash and spin cycles. This part detects when the lid is closed and locks it to prevent accidental opening, providing safety and proper cycle operation. A worn or broken lid lock can cause your washer to stop mid-cycle, display error codes, or fail to start. Replacing it restores dependable washer performance and safety compliance. Replaces Part Numbers This lid switch and lock assembly replaces DC34-00025G, AP6884125, PS12720530. Manufactured to original equipment specifications for a precise fit and long-term durability. Compatible Brands Compatible with select Samsung top-load washers manufactured by Samsung. Fits a variety of models using this specific lid lock assembly. Fixes the Following Issues Washer won’t start or stops mid-cycle Lid doesn’t lock properly Error codes related to lid switch or lock failure Washer won't enter spin or drain cycles Why Buy from Parts‑O‑Matic Factory-original genuine OEM part Fast and free U.S. shipping Trusted by appliance professionals and DIYers Backed by reliable customer support

Read more less

XPARTCO WH12X10334 Washer Lid Switch with Wire Harness The XPARTCO WH12X10334 is an aftermarket replacement washer lid switch assembly with wire harness compatible with select GE, Hotpoint, RCA, and Kenmore top-load washers — including the GTWN4250, GCWN4950, GTW180, GTWN2800, GTWN5550, GTUP270, and HSWP1000 series. The lid switch is a magnetic switch mounted near the lid hinge that detects whether the washer lid is open or closed. A magnet attached to the lid activates the switch when the lid closes — a small pin on the switch presses against an internal lever to signal the control board that it is safe to agitate or spin. This safety mechanism prevents the washer from running with the lid open. When the lid switch fails, the washer may not start, may fill with water but not proceed to the wash cycle, may stop mid-cycle, may not spin or agitate even with the lid closed, or may display lid-related error codes on models with digital displays. This assembly includes the switch and attached wire harness. It directly replaces WH12X10141, AP3968471, 1256927, AH1482372, EA1482372, and PS1482372. Installs in 20–30 minutes with basic hand tools. Quick Answer The XPARTCO WH12X10334 Washer Lid Switch fixes GE, Hotpoint, RCA, and Kenmore top-load washers that won't start, fill but don't proceed to wash, stop mid-cycle, or won't spin or agitate with the lid closed. Magnetic switch with wire harness — pin-and-lever design. Replaces WH12X10141, AP3968471, 1256927, AH1482372, EA1482372, PS1482372. Compatible with GE GTWN4250, GCWN4950, GTW180, GTWN2800, GTWN5550, GTUP270, and Hotpoint HSWP1000 series. Common Problems This Part Fixes Washer not starting — lid switch not signaling the lid is closed Washer filling with water but not proceeding to the wash cycle Washer stopping mid-cycle even though the lid is closed Washer not agitating or spinning despite the lid being closed Washer running intermittently — switch contact making and losing connection Lid-related error codes displayed on models with digital control panels Washer running with the lid open — switch stuck closed (less common but possible safety concern) Replaces Part Numbers This lid switch assembly directly replaces the following OEM and cross-reference part numbers: WH12X10334, 1256927, AGE26415, AH1482372, AP3968471, EA1482372, EAP1482372, PD00001112, PS1482372 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This lid switch assembly is compatible with select top-load washers from the following brands and series: GE top-load washers — GTWN4250D0WS, GTWN4250D1WS, GTWN4250M1WS series GE top-load washers — GCWN4950D2WS series GE top-load washers — GTW180SCJ0WW series GE top-load washers — GTWN2800D0WW series GE top-load washers — GTWN5550D0WW series GE top-load washers — GTUP270EM4WW series Hotpoint top-load washers — HSWP1000M4WW series RCA top-load washers (select GE-built models) Kenmore / Sears top-load washers (select GE-built models) Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Magnetic lid switch detects whether the washer lid is open or closed and signals the control board accordingly Pin-and-lever design — the lid's magnet activates the switch, which presses an internal pin against a lever to confirm the lid is closed Prevents the washer from agitating or spinning when the lid is open — important safety function Includes pre-attached wire harness for direct connection to the washer's wiring Replaces WH12X10141, AP3968471, 1256927, AH1482372, EA1482372, and PS1482372 Compatible with GE, Hotpoint, RCA, and Kenmore top-load washers Aftermarket replacement built to OEM-equivalent quality standards DIY repair — installs in 20–30 minutes with basic hand tools Product Specifications Part Number WH12X10334 Part Type Washer Lid Switch Assembly with Wire Harness Condition Aftermarket Replacement Application Top-Load Washers Switch Type Magnetic, pin-and-lever activation Includes Lid switch and attached wire harness Compatible Brands GE, Hotpoint, RCA, Kenmore Installation Notes ⚠️ Unplug Washer Before Starting — Wear Work Gloves Disconnect power before beginning. Wear work gloves to protect your hands. The lid switch is located near the lid hinge area at the top of the washer cabinet. Use a putty knife to release the spring clips along the front edge of the top panel (or console, depending on model), then lift the top panel to access the switch from underneath. Locate the lid switch — it is typically mounted near the hinge or under the console. Photograph the wire connections before disconnecting. Disconnect the wire harness connector, or if your model requires it, cut and splice the wires using wire strippers and crimpers. Remove the mounting screws (typically a 1/4" nut driver) and remove the old switch. Install the new WH12X10334 switch in the same position, secure the mounting screws, and reconnect or re-splice the wire harness. Reinstall the top panel by aligning and pressing down until the spring clips engage. Restore power and test by closing the lid and starting a cycle to confirm the washer agitates and spins normally. You can test the old switch's continuity with a multimeter before removal to confirm it has failed. Tools needed: Putty knife, 1/4" nut driver, wire strippers, crimpers. Frequently Asked Questions What does the washer lid switch do? The lid switch is a safety device that detects whether the washer lid is open or closed. A magnet attached to the underside of the lid activates the switch when the lid closes, which presses a small pin against an internal lever to send a signal to the control board confirming the lid is securely shut. The washer's control board uses this signal to allow agitation and spin — both of which are blocked whenever the lid is detected as open, as a safety measure to prevent injury from a spinning or moving basket. My washer fills with water but won't start the wash cycle — is it the lid switch? Yes — this is one of the most common lid switch failure symptoms. The washer is able to complete the fill phase because filling is typically not gated by the lid switch, but the agitation and spin phases require lid switch confirmation that the lid is closed. If the switch has failed and is not properly signaling lid closure, the washer fills normally but then stalls before agitating. According to repair technicians, when a washer fills and drains but does not agitate or spin, the lid switch is the first part that should be checked and is often the cause. How do I test if the lid switch has failed? Unplug the washer and access the switch as described in the installation notes. Disconnect the wire harness and set your multimeter to continuity or resistance mode. With the lid closed and the magnet engaging the switch pin, a working switch should show closed continuity. With the lid open (pin released), the switch should show open continuity. If the switch shows the same reading (either always open or always closed) regardless of lid position, the switch has failed and needs replacement. Could a bad lid switch cause water filling and draining issues too? In some specific cases, yes — some owners have reported resolving combinations of fill, drain, and spin issues by ultimately tracing the root cause back to a faulty lid switch, even after replacing other components like the water level pressure switch or control board. If you've already addressed other suspected causes for irregular cycle behavior and the symptoms persist, testing or replacing the lid switch is a low-cost troubleshooting step worth trying before assuming a major component (like the control board) needs replacement. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine GE OEM part, but is manufactured to match the magnetic switch design and wire harness configuration of the original WH12X10334 lid switch assembly. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

20A Ceramic Fuse 6.35 x 32 mm, 20A 250V - Compatible with GE, Whirlpool, Kenmore, Maytag, Frigidaire, LG, Samsung and Other Appliances Product Description Protect your appliances with the replacement 20A Slow-Blow Ceramic Fuse 6.35 x 32 mm, 20A 250V. This high-quality time-delay (slow-blow) ceramic cartridge fuse is designed for GE, Whirlpool, Kenmore, and other appliances like microwaves, washers, dryers, and spa control systems. With a ceramic body for durability and heat resistance, this fuse (6.35 x 32 mm, 20A, 250V AC) safeguards circuits from over current and short circuits while tolerating brief surges. It addresses issues like appliance failure, power loss, or blown fuses.  Note: Includes one ceramic fuse. Disconnect power before installation. Verify fuse size and rating match your appliance’s requirements. Replaces part numbers: EXP20A, MDA-20, 0326020.HXP, 0326020.MXDP, BK1-MDP-20-R, BK-MDP-V-20-R, GSA20, 8020.0605, 8020.0605.G, WB27X10388, AP3094537, AH334641, EA334641, EAP334641, PS334641, WP4375321, W11305892, W11305905, AP6009296, PS11742452, 3601-001198, AP4046006, PS4131369, 5F1CD2031S, AP4565040, 1206681, 4922155, WB27X11151, AP4980434, PS3486702, WB27X11151, AP4980434, PS3486702, WB2X3910, PS242167, AP2010811, WB2X3910, WB27X995, WB27X945, B27X10388, PS239525, AP2631556, WP8183507, 8183507, PS11745084, AP6011884, M0805101, AP6014669, PS11747931, WPM0805101, 5304423383, PS472662, AP2151673, EA472662, WB27X10928, AP3994062, WB27X10388, AH1481237, EA1481237, PS1481237, W11707984, W10138793, AP7225218, PS17629444, 3B74133Q, AP4440371, PS3522743, 5F1CD0202S, 5F1CD2031S, 3B74133K. AH3522741, EA3522741, AP4438152, PS3522741. Compatibility: Compatible with appliances including but not limited to: GE Microwaves: JE1860SH04, JVM1540SM5SS, JVM1440WH04 Whirlpool Microwaves: MH1150XMQ0, MH2175XSB0 Kenmore Microwaves: 721.62649200, 665.68612800 Whirlpool Washers: WTW5300SQ0, LSQ9544KQ0 Whirlpool Dryers: WED5300SQ0 Balboa Spa Control Systems: 30123 Other Brands: KitchenAid, Maytag, Amana, Hotpoint, and other appliances requiring 6.35 x 32 mm, 20A 250V slow-blow fuses Verify your model number or contact our support team for assistance. Key Features: ✅ Brand and Models Compatibility: Fits select GE, Whirlpool, Kenmore, KitchenAid, Maytag, Amana, Hotpoint, LG, Samsung and other appliances requiring 6.35 x 32 mm, 20A 250V fuses. 🔥 Specifications: replacement slow-blow ceramic fuse, 6.35 x 32 mm (1/4" x 1-1/4"), 20A, 250V AC, ceramic body, time-delay, 3.35–3.5 mOhms resistance, cylindrical, holder/clip mount. 💰 Cost-Effective Alternative: replacement fuse offers OEM-equivalent performance at a lower price. 🛠️ Easy Installation: Requires insulated gloves, needle-nose pliers; typically installed in 5–15 minutes. 🛡️ Reliable Fixes: Resolves appliance failure, power loss, or blown fuse issues in microwaves, washers, dryers, and spa systems. Installation Notes: Safety First: Disconnect the appliance from the power source before installation. Shop Parts-O-Matic for high-quality replacement appliance parts with a 30-day return policy. Keep your appliances running safely and efficiently today! Add to cart now for a budget-friendly fix!

Read more less

MWC21095 Microwave High Voltage Capacitor (2100VAC, 0.95µF) The MWC21095 is a universal high voltage capacitor for microwave ovens, part of the high-voltage power supply circuit that steps up household voltage to the extreme level the magnetron needs to generate cooking power. Working alongside the high-voltage diode and transformer, this capacitor doubles the rectified voltage feeding the magnetron — it's a core piece of why a microwave can produce thousands of volts internally from a standard household outlet. Rated 2100VAC, 0.95µF, ±3% tolerance, oval aluminum can construction with two male terminals spaced 1/4" (6.35mm) apart. Overall dimensions approximately 3.35"H (body) x 2.75"W x 2.05"D, with the terminal housing adding roughly 1.3" to the total height. Over time, the internal dielectric can break down from repeated high-voltage cycling, causing the capacitor to lose capacitance or fail outright — sometimes shorting internally. Symptoms of a failing capacitor include the microwave running (light on, turntable turning, fan running) but not heating food, a buzzing or humming noise from the high-voltage compartment, arcing or sparking sounds, or the microwave tripping a breaker shortly after starting. ⚠️ Extreme Danger — Lethal Voltage Risk A microwave's high voltage capacitor can retain a lethal electrical charge for a long time after the microwave has been unplugged — this is one of the most dangerous components in any household appliance to work on. Even with the microwave fully unplugged, this capacitor can still deliver a fatal shock if handled incorrectly. Before touching any component in the high-voltage compartment, the capacitor must be safely discharged by shorting both terminals to the chassis ground using an insulated-handle screwdriver, and that discharge should be verified with a multimeter before proceeding. If you are not fully trained and confident in safely discharging a high voltage capacitor, do not attempt this repair — have a qualified appliance technician replace this part instead. This applies every time, regardless of how long the microwave has been unplugged. Quick Answer The MWC21095 Microwave High Voltage Capacitor fixes microwave ovens that run (light, turntable, fan all working) but don't heat food, make a buzzing or arcing sound from the high-voltage compartment, or trip the breaker shortly after starting. 2100VAC, 0.95µF, ±3%, oval, 2 male terminals (1/4"/6.35mm spacing). Retains a lethal electrical charge even after unplugging — must be properly discharged before any handling. Common Problems This Part Fixes Microwave runs (light on, turntable turning, fan running) but doesn't heat food Buzzing or humming noise from the high-voltage compartment Arcing or sparking sound during operation Microwave trips the breaker shortly after starting a cook cycle Microwave that used to heat inconsistently and has now stopped heating altogether Visible bulging, leaking, or discoloration on the capacitor can Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers TJ13QBP21095, 13QBP0300, 13QBP21095, AP5633423, RC-QZA234WRE0, RC-QZB011MRE0, RCQZA331WRZZ, 5304513458, PD00065299, EAP12365444, 4584979, AP6301645, PS12365444, 00631397, 631397, PD00044249, EAP10057840, 4161979, AP5950362, PS10057840, WB27X11031, PD00040188, EAP2339855, 1474116, AP4362390, PS2339855, WB27X10073, PD00045875, EAP239187, 769853, AP2025984, PS239187, WB27X11011, PD00087136, EAP2345628, 1474103, AP4368101, PS2345628, 2501-001016, 2028385, AP4033712, PS4130923, 8206562, PD00074258, EAP1486840, 1200936, AP3890709, PS1486840, 5304528930, 5304464253, AP7017693, PS2203382, WB27X10009, 254534, AH239117, EA239117, AP2025928, PS239117, WP815073, AP6011690, PS11744888, 2501-000260, AP4033659, PS4130923 This is a universal component rather than a single-manufacturer part, so the specific OEM number your microwave's label references will vary by brand (GE, Whirlpool, Frigidaire, Samsung, LG, and others). This capacitor is a correct replacement for any microwave capacitor matching the 2100VAC, 0.95µF specification. If you have your original part number, contact our support team and we will verify compatibility before you order. Compatibility This capacitor is a universal replacement compatible with household microwave ovens across all major brands — GE, Whirlpool, Frigidaire, Samsung, LG, and others — wherever the original capacitor is rated: 2100VAC 0.95µF (or a rating within roughly 10–20% higher than your original — see FAQ) Oval shape with 2 male terminals, 1/4" (6.35mm) spacing Note: Voltage rating must match your original capacitor exactly — never substitute a lower voltage rating, and don't assume a higher voltage rating is automatically safe on this component the way it is with an HVAC run capacitor, since the high-voltage diode in the circuit must also be rated to match. Capacitance (µF) has more tolerance than voltage: a modest increase over the original rating is generally acceptable, but always try to match as closely as possible. If you're unsure whether this capacitor matches your microwave's original specification, check the rating printed on your existing capacitor's can before ordering, or contact our support team for help confirming compatibility. Key Features Universal microwave high voltage capacitor — a core component of the high-voltage power supply circuit 2100VAC, 0.95µF, ±3% tolerance Oval aluminum can construction for durability Resolves "runs but doesn't heat," "buzzing or arcing noise," and "trips the breaker" symptoms caused by capacitor failure 2 male terminals, 1/4" (6.35mm) spacing, for a direct plug-on fit to standard microwave wiring Compatible with GE, Whirlpool, Frigidaire, Samsung, LG, and most other major microwave brands Built to meet or exceed industry-standard specifications for this capacitor class Product Specifications Part Number MWC21095 Part Type Microwave High Voltage Capacitor Condition New — Universal Replacement Part Voltage Rating 2100VAC Capacitance 0.95 µF (mfd) Tolerance ±3% Shape Oval Terminals 2 male, 1/4" (6.35mm) spacing Overall Height 8.5cm / 3.35 in. Body Height 7cm / 2.75 in. Body Width 5.2cm / 2.05 in. Terminal Housing Height 3.3cm / 1.3 in. Material Aluminum can Application Household Microwave Ovens Quantity 1 high voltage capacitor Compatible Brands Universal — GE, Whirlpool, Frigidaire, Samsung, LG, and most other major brands Installation Notes ⚠️ Extreme Danger — Discharge Fully Before Any Contact Unplug the microwave and wait, but never assume the capacitor is safe based on time alone. Remove the outer cabinet to access the high-voltage compartment. Before touching anything else, discharge the capacitor by shorting both terminals to the chassis ground using an insulated-handle screwdriver — do this deliberately and do not rush. Verify the capacitor reads no charge with a multimeter before proceeding. Never assume a capacitor is discharged just because time has passed, and never touch the terminals directly, even with the microwave unplugged. If you are not completely confident performing this discharge procedure safely, stop and have a qualified appliance technician complete this repair. ⚠️ Match The Terminal Wiring Exactly Wear insulated gloves and safety glasses. After confirming the capacitor is fully discharged, photograph the wiring on both terminals before disconnecting anything. Remove the mounting bracket or strap holding the old capacitor in place, and disconnect each wire from its terminal. Install the new MWC21095 in the same mounting position, and reconnect each wire to its matching terminal exactly as photographed — the two terminals are not interchangeable in some circuit configurations, so accuracy here matters. Secure the mounting bracket or strap. Reinstall the outer cabinet before restoring power. Plug the microwave back in and test with a cup of water to confirm normal heating without unusual noise. Frequently Asked Questions Is it really dangerous to work on this even with the microwave unplugged? Yes, genuinely. This is one of the most dangerous repairs a person can attempt on a household appliance, because this capacitor is specifically capable of retaining a lethal electrical charge long after the microwave has lost power. Unplugging the microwave is a necessary first step, but it does not make the capacitor safe to touch on its own — proper discharge with an insulated tool, verified with a multimeter, is required every time before any contact with this component. My microwave runs completely normally — light, turntable, fan — but food doesn't heat. Is this the capacitor? It's one of the most common causes of exactly that symptom. Since the capacitor is part of the circuit that generates the high voltage the magnetron needs, a failed capacitor can leave every other function of the microwave working normally while the actual cooking power is missing entirely. Can I use a capacitor with a slightly different µF rating than my original? Some tolerance is generally acceptable here — a modest increase over your original rating, often cited as up to roughly 10-20% higher, typically works fine, since the capacitance value isn't as tightly critical to the magnetron's operation as some assume. That said, always aim to match your original rating as closely as possible, and never substitute a different voltage rating; the voltage must match your original capacitor exactly. Should I replace the high-voltage diode at the same time? It's worth considering. The capacitor and diode work together in the same high-voltage circuit, and a failure in one can sometimes stress or damage the other. If your capacitor failed and you're already taking the precautions needed to safely access this compartment, it may be a reasonable time to inspect or replace the diode as well, particularly if the microwave shows signs of a more significant electrical fault. Is this a genuine OEM part? This is a universal replacement part rather than a brand-specific OEM part. Because high voltage capacitors of this type are a standardized component defined by their electrical specifications, this capacitor is a correct replacement for any microwave's original capacitor sharing the same 2100VAC, 0.95µF rating — regardless of which brand originally installed it. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Replacement Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

422133CM Surface Element Infinite Switch 120V, 15 Amp ceramic element. Fits Bosch glasstop free standing ranges Replaces Part Numbers:00422133, 422133, AH3462872, EA3462872, AP3723298, PS3462872, PS8713176.   This is an aftermarket part that can be used as a replacement for the OEM part. California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

DA34-00041B Refrigerator Door Switch – Replacement for Samsung Product Overview The DA34-00041B Refrigerator Door Switch is an aftermarket replacement that controls interior lighting and signals the control board when the refrigerator or freezer door is open or closed. A malfunctioning switch can result in the light staying off or on, cooling fans not running correctly, or even door-related error codes. Replacing a faulty switch with this part helps restore normal operation and energy efficiency. Replaces Part Numbers This part replaces DA34-00041B, DA34-10110B, AP5957961, PS10061325. It is designed to meet OEM specifications for reliable fit and performance in Samsung-built refrigerators. Compatible Brands This door switch is compatible with refrigerators manufactured by Samsung and Kenmore (Samsung-built). It fits a wide range of French door, bottom freezer, and side-by-side models. Fixes the Following Issues Refrigerator light not turning on or off Cooling fan not operating when door closes Door-related error messages Inconsistent temperature regulation Why Buy from Parts‑O‑Matic Affordable and reliable aftermarket solution Fast and free U.S. shipping Easy to install with no special tools required Trusted by appliance repair professionals and DIYers

Read more less

W11305308 Dishwasher Genuine Whirlpool Control Board Control Board  Main electronic control board. Fits Specific Whirlpool Dishwasher Models. Replaces Part Numbers:W11305308, W11131683, W10918994, W11170192, W11227807, AP6832578, PS12704681.

Read more less

W10551671 Dishwasher Touchpad and Control Panel Genuine OEM Replaces Part Numbers: WPW10551671, W10551671, 4448286, W10447837, W10456292, W10551664, W10577251, W10584823, W10669887, AP6022869, PS11756206.    California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less