Search results for "dryer idler pulleys"

XPARTCO 3977394 Dryer Thermal Cut-Off Kit –  Compatible with Whirlpool, Kenmore, Maytag, and KitchenAid Dryers Product Description Protect your dryer from overheating with the XPARTCO 3977394 Dryer Thermal Cut-Off Kit. This high-quality aftermarket replacement shuts off the heating element if the dryer temperature rises above safe operating limits. A failed cut-off can cause no-heat issues or overheating during drying cycles. Installing this reliable XPARTCO 3977394 kit restores safe temperature control and helps prevent damage to internal components. Replaces Part Numbers XPTC352, 3977394, 352F, EXPTC352 Compatibility This replacement thermal cut-off kit fits select Whirlpool, Kenmore, Maytag, Roper, Estate, Crosley, and KitchenAid dryers. Example compatible models include (but are not limited to): Whirlpool WED4815EW1, Kenmore 110.86573110, and Maytag MEDC215EW1. Always verify your dryer’s model number before ordering. Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement – Matches OEM safety and temperature performance 🔥 Overheat Protection – Automatically shuts off power to the heating element if the dryer overheats 💰 Cost-Effective Fix – Affordable alternative to OEM thermal cut-off kits 🛠️ Easy Installation – Direct-fit design with included thermostats and connectors 🛡️ Fixes Common Issues – Solves dryer not heating, overheating, or shutting off prematurely 📐 Product Specification Part Number: 3977394 Component Type: Dryer Thermal Cut-Off Kit Includes: Thermal cut-off, high-limit thermostat, mounting hardware, and wire connectors Temperature Rating: Cut-off opens at ~352°F. Material: Metal thermostat housing and heat-resistant components Compliance: Built to OEM-equivalent quality standards (not OEM) 🛠️ Installation Notes Tools Needed: Nut driver, Phillips screwdriver ⚠️ Safety First: Always unplug the dryer before performing any repairs to prevent electrical shock. Steps: Disconnect power and remove the rear dryer panel. Locate the heating element housing and identify the cut-off and thermostat. Disconnect wires and remove the old components. Install the new 3977394 cut-off and thermostat in the same locations. Reconnect wires, reassemble the back panel, and restore power. Run a short test cycle to verify proper heating. ⏱️ Time Required: 15–25 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Appliance Parts Supplier 🔄 30-Day Return Policy Keep your dryer safe and efficient — Add to Cart Now for a reliable, budget-friendly repair!

Read more less

XPARTCO DC47-00018A Dryer Hi Limit Thermostat The XPARTCO DC47-00018A is an aftermarket replacement cycling high-limit thermostat for Samsung and select Kenmore electric dryers. This is a genuine, automatically resetting thermostat — not a one-time fuse. It monitors temperature in the heating circuit and opens to cut power to the heating element at approximately 260°F, protecting the dryer from overheating. Once the temperature drops to around 210°F, it closes again on its own, letting the dryer resume heating without any part replacement needed. This thermostat works alongside a downstream thermal fuse (such as our DC96-00887C listing) in the same overheat-protection circuit. If this thermostat is cycling excessively, tripping prematurely, or failing to regulate temperature correctly, it can put stress on that thermal fuse, sometimes causing it to blow as a last-resort safety measure. Symptoms of a failing high-limit thermostat include no heat or insufficient heat, drying that takes too long, or the dryer shutting off too soon before a load is fully dry. It directly replaces 35001092, WP35001092, 1122485, AP4201898, PS4205217, EAP2430930, PS2430930, and AP6008682. Quick Answer The XPARTCO DC47-00018A Dryer Hi Limit Thermostat fixes Samsung and select Kenmore electric dryers with no heat or insufficient heat, drying that takes too long, or premature shutoff before a load is fully dry. Opens at approximately 260°F, resets automatically around 210°F. Replaces 35001092, WP35001092, 1122485, AP4201898, PS4205217, EAP2430930, PS2430930, AP6008682. This is a resettable thermostat, not a fuse — it does not need replacement after each trip. It's a different component from our DC96-00887C thermal fuse listing, though the two are often checked together. Common Problems This Part Fixes Dryer has no heat or insufficient heat Drying takes too long to complete a cycle Dryer shuts off too soon, before clothes are fully dry Timer will not advance through the cycle Dryer that stopped working suddenly after running unusually hot Dryer with a history of repeated downstream thermal fuse failures Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dryer high-limit thermostat directly replaces the following OEM and cross-reference part numbers: DC47-00018A, AP4201898, T-O-D 60T11, ASM33627, 1122485, PD00002011, PS4205217. WP35001092, 35001092, PD00004704, EAP11741822, AP6008682, AWP47350, PS11741822, L260-50F If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This high-limit thermostat is compatible with select Samsung electric dryers, and also fits select Kenmore dryers built on the Samsung platform, including model numbers such as: DV5471AEW/XAA DV40J3000EW/A2, DV42H5000EW/A3, DV45H7000EW/A2, DV48H7400EW/A2 DV400EWHDWR/AA DVE50M7450W/A3 Note — resettable thermostat, not a fuse: This DC47-00018A is a true cycling thermostat that resets itself automatically. Our DC96-00887C listing, despite frequently being labeled a "thermostat" on other marketplaces, is actually a one-time thermal fuse mounted separately on the blower housing — it cannot reset and must be replaced once blown. The two are different device types serving the same circuit. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Aftermarket replacement cycling high-limit thermostat — automatically resetting, no replacement needed after each trip Opens at approximately 260°F, resets around 210°F Resolves "no heat," "insufficient heat," "takes too long to dry," and "shuts off too soon" symptoms Genuine thermostat, distinct from the downstream thermal fuse in the same circuit No special tools required for installation Replaces 35001092, WP35001092, 1122485, AP4201898, PS4205217, EAP2430930, PS2430930, and AP6008682 Compatible with Samsung and select Kenmore electric dryers Aftermarket replacement built to OEM-equivalent quality standards Product Specifications Part Number XPDC47-00018A OEM Part Number DC47-00018A Part Type Dryer Cycling High-Limit Thermostat Condition Aftermarket Replacement Type Automatically resetting — not a one-time fuse Open Temperature ~260°F Reset Temperature ~210°F Related Component DC96-00887C thermal fuse (blower housing, different device, sold separately) Quantity 1 high-limit thermostat Compatible Brands Samsung, select Kenmore Installation Notes ⚠️ Unplug Dryer Before Starting Disconnect power at the outlet or shut off the circuit breaker before beginning. Wear work gloves. Access is typically through the rear panel, near the heater duct and blower housing area where this thermostat is mounted. Photograph the wiring connections before disconnecting anything, since this thermostat can be positioned close to other similar-looking components in the same circuit. Remove the old thermostat from its mounting position, noting orientation, and disconnect its wiring. Install the new DC47-00018A in the same position, reconnecting wiring exactly as photographed. Reassemble the panel, restore power, and run a full test cycle to confirm normal, consistent heating with no premature shutoffs. Tools needed: Phillips or nut driver (model-dependent), work gloves. Frequently Asked Questions Do I need to reset this thermostat after it trips, or replace it? Neither, in normal operation — this is a genuine cycling thermostat that resets itself automatically once the dryer cools to around 210°F. You should only need to replace it if it has failed outright (stuck open, stuck closed, or no longer switching at the correct temperatures), not simply because it tripped once during normal operation. My dryer shuts off before the load is fully dry. Is that this part? It's a strong possibility. If this high-limit thermostat is tripping prematurely — opening at a lower temperature than it should — the dryer can cut heat and end the cycle early even though the load isn't actually dry yet. This is one of the more common symptoms this thermostat addresses. My thermal fuse keeps blowing. Could this thermostat be the underlying cause? Yes, this is worth investigating. This thermostat and the downstream thermal fuse (our DC96-00887C listing) protect the same circuit at different points. If this thermostat isn't regulating temperature correctly — cycling excessively or failing to catch a temperature spike — the thermal fuse can end up blowing repeatedly as the last line of defense. If you've replaced the fuse more than once, checking or replacing this thermostat at the same time is a reasonable next step. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Samsung OEM part, but is manufactured to match the electrical specifications and opening/reset temperatures of the original DC47-00018A high-limit thermostat used in compatible Samsung and Kenmore electric dryers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO 279769 Dryer Thermostat Kit The XPARTCO 279769 is an aftermarket replacement thermal cut-off and high-limit thermostat kit for Whirlpool, Kenmore, Roper, KitchenAid, Maytag, Amana, Estate, Crosley, and Admiral electric dryers. This kit bundles two components that guard against overheating at different thresholds: the 3390291 high-limit thermostat (rated L250-80F) monitors internal temperature and interrupts power at approximately 250°F to prevent overheating, then resets itself automatically once the dryer cools — no replacement needed after each trip. The 3977394 thermal cut-off fuse is the backup: rated at 352°F, it's a one-time safety device that permanently opens the circuit if temperatures climb high enough that the thermostat alone didn't prevent an overheat. These two parts are sold together and should be replaced together as a set, since they protect the same circuit and tend to be stressed by the same underlying problem. Whirlpool's own guidance is direct: when the thermal cut-off fails, it usually indicates a venting problem, and failing to correct that airflow issue will cause repetitive failures even with new parts installed. Symptoms include the dryer not heating, clothes coming out extremely hot, or the dryer not running at all. This kit is commonly used alongside heating element 4391960. It directly replaces 279769, 279548, 2796769, 279769VP, 2821, 2004, 3387812, 3389946, 3398671, 3977394, 695563, 80001, SET184, SET198, TJSET198, ET184, AP3094224, AH334278, EA334278, EAP334278, PD00002485, PS334278, WP3390291, AP6008306, 3390291, 696397, and PS11741441. As an aftermarket replacement, the 279769 kit is built to OEM-equivalent quality standards. Quick Answer The XPARTCO 279769 Dryer Thermostat Kit fixes Whirlpool, Kenmore, Roper, KitchenAid, Maytag, Amana, Estate, Crosley, and Admiral electric dryers with no heat, no power at all, or clothes coming out dangerously hot. Includes the 3390291 high-limit thermostat (250°F, auto-resetting) and the 3977394 thermal cut-off fuse (352°F, one-time). Replaces 279548, 2796769, 279769VP, 3387812, 3389946, 3398671, 3977394, 695563, 80001, AP3094224, PS334278, WP3390291, AP6008306, 3390291, 696397, PS11741441. Always inspect and clean the exhaust venting when replacing this kit — a blown thermal fuse is a symptom of restricted airflow, and skipping the vent check leads to repeat failures. What's In The Kit Component Rating Function 3390291 High-Limit Thermostat L250-80F (~250°F) Interrupts power to prevent overheating, resets automatically once the dryer cools. 3977394 Thermal Cut-Off Fuse 352°F One-time backup safety device — permanently opens the circuit if temperature exceeds safe limits. Cannot reset. Common Problems This Kit Fixes Dryer won't start at all — no lights, no tumble, no response Dryer runs but produces no heat Clothes coming out extremely hot, hot enough to be uncomfortable to handle Dryer that stopped working suddenly after running unusually hot Repeated thermal cut-off failures on a dryer with a known venting issue Dryer that shuts off prematurely mid-cycle Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dryer thermostat kit directly replaces the following OEM and cross-reference part numbers: 279769, 2004, 279548, 2796769, 279769VP, 2821, 3387812, 3389946, 3398671, 3977394, 695563, 80001, AH334278, EA334278, AP3094224, OEM9282681, SET184, SET198E, AP334278, L250-80F, PS334278, AWP39149, PD00002485. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This thermostat kit is compatible with select Whirlpool electric dryers, and also fits select Kenmore, Roper, KitchenAid, Maytag, Amana, Estate, Crosley, and Admiral dryers built on the Whirlpool platform, including model numbers such as: 7MWET4027HW0 WET3300XQ0 WET4027EW0, WET4027EW1 WET4027HW0, WET4027HW1, WET4027HW2 WETLV27FW0, WETLV27HW0, WETLV27HW1, WETLV27HW2, WETLV27HW3 YWET4027EW1, YWET4027HW0, YWET4027HW1, YWET4027HW2 Note: This kit was used on Whirlpool-built electric dryers primarily from 1985 to 1995. Always verify your full model number before ordering, since Whirlpool used several different thermostat and fuse designs across its dryer lineup over the years. Contact our support team with your model number if you're unsure. Key Features Aftermarket replacement built to match Whirlpool's factory-specified thresholds for both components 2-piece kit: 3390291 high-limit thermostat (250°F, auto-resetting) and 3977394 thermal cut-off fuse (352°F, one-time) Resolves "no heat," "no power at all," and "clothes coming out extremely hot" symptoms Addresses two overheat-protection thresholds in the same circuit at once Commonly used alongside heating element 4391960 Direct drop-in replacement for both original components Replaces 279548, 2796769, 279769VP, 3387812, 3389946, 3398671, 3977394, 695563, 80001, AP3094224, PS334278, WP3390291, AP6008306, 3390291, 696397, and PS11741441 Compatible with Whirlpool, Kenmore, Roper, KitchenAid, Maytag, Amana, Estate, Crosley, and Admiral electric dryers Aftermarket replacement built to OEM-equivalent quality standards Product Specifications Kit Part Number 279769 Kit Contents 1x High-Limit Thermostat (3390291), 1x Thermal Cut-Off Fuse (3977394) OEM Part Number 279769 Condition Aftermarket Replacement Brand Whirlpool High-Limit Thermostat Rating L250-80F (~250°F, auto-resetting) Thermal Fuse Rating 352°F (one-time, non-resettable) Companion Heating Element 4391960 (commonly used together) Repair Difficulty Easy to Moderate — basic tools required Compatible Brands Whirlpool, Kenmore, Roper, KitchenAid, Maytag, Amana, Estate, Crosley, Admiral Installation Notes ⚠️ Unplug Dryer Before Starting — Inspect And Clean The Venting Before Reassembling Disconnect power at the outlet or shut off the circuit breaker before beginning. Wear work gloves. Access is typically through the rear panel, near the heating element and blower housing where both components are mounted. Photograph the wiring connections before disconnecting anything, since the thermostat and fuse can be easy to swap positions by mistake. Remove each old component from its mounting position, noting orientation, and disconnect its wiring. Before reassembling, fully inspect and clean the dryer's exhaust vent, from the lint trap housing all the way to the exterior vent hood, checking for lint buildup, crushed sections, or excessive length. When the thermal cut-off fails, it usually indicates a venting problem, and failing to correct that airflow issue will cause repetitive failures even with these new parts installed. Install the new 3390291 thermostat and 3977394 thermal fuse from this kit in the same positions as the parts they replace, reconnecting wiring exactly as photographed. Reassemble the panel, restore power, and run a full test cycle to confirm normal, consistent heating with no premature shutoffs. Tools needed: Phillips or nut driver (model-dependent), work gloves. Frequently Asked Questions My clothes are coming out extremely hot, hot enough to burn my hands. Is this the right kit? Yes, this is a documented symptom this kit addresses. If the high-limit thermostat fails to regulate temperature correctly, the dryer can run far hotter than it should, producing dangerously hot clothing at the end of a cycle. Whirlpool's own parts support has specifically pointed customers with this exact complaint toward this kit. Stop using the dryer if you notice this symptom and replace both components promptly. Why do I need to replace both the thermostat and the fuse together? These two parts protect the same circuit at different thresholds and tend to fail from the same underlying cause. If the high-limit thermostat isn't regulating temperature correctly, the thermal fuse often ends up blowing as the backup safety measure. Replacing only one risks the other failing again shortly after, so they're sold and serviced together as a set. I replaced this kit and the dryer failed again. What should I check? This is a strong sign the underlying cause — almost always restricted airflow — was never addressed. Thoroughly inspect and clean the entire exhaust path from the lint trap housing to the outside vent hood, checking for lint buildup, crushed or kinked ductwork, or a vent run that's too long. Failing to correct a venting issue will cause repetitive failures of this kit even when it's brand new. Should I replace the heating element at the same time? It's worth considering if your dryer's heating element (commonly 4391960 on compatible models) is original and has been running alongside a failing thermostat, since sustained overheating can stress the element as well. It's not required, but since you'll already have the panel open for this repair, it's a reasonable time to inspect the element for visible damage. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured to match the temperature thresholds and mounting configuration of the original 279769 high-limit thermostat and thermal cut-off fuse kit used in compatible Whirlpool, Kenmore, Roper, KitchenAid, Maytag, Amana, Estate, Crosley, and Admiral electric dryers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

4 Pack - XPARTCO 3977393 Dryer Thermal Cut Off (309°F) – Compatible with Whirlpool, Maytag & Kenmore Dryers Product Description Protect your dryer from overheating with the XPARTCO 3977393 Dryer Thermal Cut Off (309°F). This high-quality aftermarket replacement is a critical safety component designed to permanently interrupt power to the heating circuit if temperatures exceed 309°F (154°C). A blown thermal cut off can result in no heat. Replacing it with this reliable XPARTCO component helps restore safe operation and prevent further damage to heating elements or internal components. XPARTCO provides cost-effective aftermarket appliance parts engineered to match original fit and performance. Replaces Part Numbers 3977393, AP3094244, PS334299, EAP334299 Compatibility This replacement dryer thermal cut off fits select Whirlpool, Maytag, Kenmore (Whirlpool-manufactured), Amana, Estate, and Roper dryers. Commonly installed on the heater housing assembly. Always verify your dryer’s model number before ordering.Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement – Matches OEM temperature rating and fit 🌡️ 309°F (154°C) Cut-Off Rating – Designed for high-heat safety protection 🛡️ Prevents Overheating Damage – Protects heating element and dryer components 🧩 Direct-Fit Design – Installs easily without modification 💰 Cost-Effective Repair – Affordable alternative to OEM thermal cut offs 📐 Product Specification Part Number: 3977393 - Pack Component Type: Dryer Thermal Cut Off Temperature Rating: 309°F (154°C) Function: One-time over-temperature safety cutoff Mounting: Screw-mounted Application: Dryer heater housing assembly Quality Level: Aftermarket replacement (not OEM) 🛠️ Installation Notes Tools Needed: Phillips screwdriver, nut driver ⚠️ Safety First: Unplug the dryer before servicing to avoid electrical shock. Basic Steps: Disconnect dryer power. Remove rear panel to access heater housing. Locate and disconnect the old thermal cut off. Remove mounting screws and install the new XPARTCO 3977393 cut off. Reconnect wiring and reassemble the dryer. Restore power and test operation. ⏱️ Time Required: 20–30 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Aftermarket Appliance Parts 🔄 30-Day Return Policy Restore dryer safety and prevent overheating — Add to Cart Now for a dependable, budget-friendly repair!

Read more less

ERP 3406108 Dryer Door Switch  Replaces Part Numbers: WP3406108, 3406108, PS11741702, AP6008562  Description: This Door Switch is a replacement part for select Whirlpool dryer models. It is responsible for detecting whether the dryer door is open or closed. When the door is closed, the switch allows the dryer to operate. Conversely, if the door is open, the switch interrupts the electrical circuit to prevent the dryer from running, ensuring safety during use. Fits Models:   LTE5243DQ1 , LTE5243DQ2 , LTE5243DQ3 , LTE5243DQ4 , LTE5243DQ5 , LTE5243DQ6 , LTE5243DQ7 , LTE5243DQ8 , LTE5243DQ9 , LTE5243DQA , LTE5243DQB , LTE5243DT2 , LTE5243DT3 , LTE5243DT4 , LTE5243DT5 , LTE5243DT6 , LTE5243DT7 , LTE5243DZ1 , LTE5243DZ2 , LTG5243DQ1 , LTG5243DQ2 , LTG5243DQ3 , LTG5243DQ4 , LTG5243DQ5 , LTG5243DQ6 , LTG5243DQ7 , LTG5243DQ8 , LTG5243DQ9 , LTG5243DQA , LTG5243DQB , LTG5243DQC , LTG5243DT2 , LTG5243DT3 , LTG5243DT4 , LTG5243DT5 , LTG5243DT6 , LTG5243DT7 , LTG5243DT8 , LTG5243DZ1 , LTG5243DZ2 , WET4024EW0 , YLTE5243DQ2 , YLTE5243DQ3 , YLTE5243DQ4 , YLTE5243DQ5 , YLTE5243DQ6 , YLTE5243DQ7 , YLTE5243DQ8 , YLTE5243DQ9 , YLTE5243DQA , YLTE5243DQB , YWET4024EW0. This is an aftermarket part that can be used as a replacement for the OEM part. 

Read more less

(2 Pack) EXP571 Dryer Door Catch Product Overview This Door Catch is a replacement part for specific Maytag, Kenmore, LG, Frigidaire, GE, Amana, Whirlpool dryer models. It includes the door catch. This part ensures the dryer door remains securely closed during operation, preventing heat loss and ensuring the appliance functions efficiently. Common causes of a bad door catch include regular wear and tear, physical damage, or misalignment of the door, which can impact the catch's ability to latch properly. Fix a loose or non-latching dryer door with this aftermarket replacement for part number EXP571. This dryer door catch holds the dryer door securely closed during operation to ensure proper airflow and drying performance. Designed to fit specific Maytag, Kenmore, LG, Frigidaire, GE, Amana, Whirlpool dryer models. ✅ Key Features: High-quality aftermarket replacement Made from durable plastic for long-lasting use Designed to securely latch the door shut Simple snap-in installation — no tools required Helps prevent cycle interruption due to door opening 🔁 Replaces OEM Part Numbers: WP71002106, WP3389441, 3389441, 71002106, AP6010685, PS11743869, AP6008299, PS11741434, WE1X1195, AP2042209, PS266896, 131658800, AP2107362, PS418433, 5307521419, 10690002, 10690001. ⚠️ Common Symptoms Fixed: Dryer door won’t stay closed Dryer won’t start due to open door switch Door pops open during a cycle Visible wear or damage to original catch 🧰 Compatible Brands: ✔️ Frigidaire✔️ Electrolux✔️ Kenmore (Frigidaire-built)✔️ Whirlpool✔️ Maytag✔️ Crosley✔️ White-Westinghouse 📌 Need help verifying compatibility? Send us your dryer’s model number — we’ll check it for you. 🚚 Why Buy from Parts-O-Matic ? ✅ Reliable aftermarket performance ✅ Always Fast and Free U.S. shipping ✅ Easy DIY repair with trusted support ✅ Backed by excellent customer service 🛒 Fix your dryer’s latching issue today — order the EXP71 dryer door catch from parts-o-matic.com, and enjoy fast, free U.S. shipping!

Read more less

279570 Genuine OEM Whirlpool Dryer Door Catch Kit The 279570 is a Genuine OEM Whirlpool dryer door catch and strike kit compatible with a wide range of Whirlpool, Kenmore, Roper, Estate, Amana, Crosley, Inglis, KitchenAid, Maytag, and Admiral dryers. The door catch is the spring-clip mechanism on the dryer door that snaps over the door strike to hold the door firmly closed during operation, activating the door switch so the dryer can run. When the catch breaks, wears out, or loses tension, the door will not stay closed, the door switch will not be activated, and the dryer will either not start or will stop mid-cycle. The strike is the corresponding post or tab on the dryer cabinet that the catch engages. This Genuine OEM kit includes three color-coded door catches of different tensions and two metal door strikes, plus one screw. Because the tension of the catch must match the original, Whirlpool includes three options in the kit — each is color-coded and numbered on the back. Refer to identify which catch is correct for your model. The kit directly replaces a very large list of older cross-reference numbers including 279570VP, 3493, 2003, 8208, 279280, 279337, 696144, 693717, AP3094183, PS334230, and dozens more. Installs in under 15 minutes with a Phillips screwdriver. Quick Answer The 279570 Genuine OEM Whirlpool Dryer Door Catch Kit fixes dryers where the door won't stay closed, pops open mid-cycle, or won't activate the door switch to start. Kit includes 3 color-coded catches (different tensions), 2 metal strikes, 1 screw. Use the catch that matches your original. Genuine OEM. Compatible with Whirlpool, Kenmore, Roper, Estate, Amana, Crosley, Inglis, KitchenAid, Maytag, and Admiral dryers. Installs in under 15 minutes. Common Problems This Kit Fixes Dryer door will not stay closed during the drying cycle Door pops open mid-cycle, stopping the dryer Dryer will not start — door switch not being activated by a worn or broken catch Door feels loose or does not click shut firmly when closed Door catch visibly cracked, broken, or missing Door strike bent or missing — door cannot engage the catch properly Dryer requires the door to be held or pushed closed to stay running Replaces Part Numbers This door catch kit directly replaces the following OEM and cross-reference part numbers: 279570, 14205029, 14205577, 14210022, 2003, 236876, 236877, 241282, 241890, 26000279570, 261847, 263067, 279280, 279337, 279469, 279570VP, 291949, 3390239, 3392538, 3398175, 342295, 347813, 3493, 4165234, 51651001, 51655001, 66021, 690081, 690082, 693717, 694343, 696144, 8208, 830751, 834767, 834813, 834943, 834944, AH334230, DE902, EA334230, EAP334230, FSP279570, AP3094183, AWP39897, PD00002346, PS334230. Contact our support team with your model number if you need confirmation before ordering. Compatibility This door catch kit is compatible with select dryers from the following brands: Whirlpool dryers (gas and electric) Kenmore / Sears dryers (Whirlpool-built models) Roper dryers Estate dryers Amana dryers Crosley dryers Inglis dryers KitchenAid dryers Maytag dryers Admiral dryers Important: This kit includes three catches with different spring tensions, color-coded and numbered on the back. You must use the catch that matches the tension of your original. Using the wrong tension catch may result in a door that is too hard to open or too easy to pop open. Key Features Genuine OEM kit manufactured by Whirlpool to factory specifications — guaranteed fit and performance Holds the dryer door closed and activates the door switch so the dryer can run safely Kit includes 3 color-coded door catches (different spring tensions), 2 metal door strikes, 1 screw Catches are color-coded and numbered on the back — use the one that matches your original. Plastic catches with metal strikes and metal screw — durable construction for long service life Consolidates a very large list of older Whirlpool-family door catch cross-reference numbers Compatible with 10 major appliance brands on the Whirlpool platform Quick DIY repair — installs in under 15 minutes with a Phillips screwdriver Product Specifications Part Number 279570 Part Type Dryer Door Catch and Strike Kit Condition Genuine OEM Application Gas and Electric Dryers Kit Includes 3 color-coded door catches (different tensions), 2 metal strikes, 1 screw Material Plastic catches / Metal strikes Color White / Silver Catch Selection Color-coded and numbered, Use the catch that matches your original Compatible Brands Whirlpool, Kenmore, Roper, Estate, Amana, Crosley, Inglis, KitchenAid, Maytag, Admiral Installation Notes ⚠️ Unplug Dryer Before Starting Disconnect power before beginning. using the wrong tension catch will result in incorrect door resistance. Open the dryer door and locate the old door catch on the inside of the door panel and the strike on the dryer cabinet opening. To remove the old catch: press the retaining tabs and pull the catch free from its slot, or unscrew the mounting screw. Install the correct new catch into the same position. To replace the strike: remove the old strike (typically held by a single screw) and install the new strike in the same position. Close the dryer door to confirm it latches firmly with a satisfying click. Restore power and run a short test cycle to confirm the door stays closed and the dryer operates normally. Tools needed: Phillips screwdriver; needle-nose pliers may help with catch removal on some models. Frequently Asked Questions Why does the kit include three different catches? Whirlpool used door catches with different spring tensions across its dryer lineup — a lighter catch on some models and a stiffer catch on others. To cover all compatible models in a single kit, Whirlpool includes three catches of different tensions, each color-coded and numbered on the back. It is important to use the correct one — using a catch with too little tension may allow the door to pop open, while a catch with too much tension may make the door difficult to open. Do I need to replace both the catch and the strike, or just one? It depends on which component has failed. The catch (the spring-clip on the door) is the more commonly replaced part — it wears out from repeated use faster than the strike. Inspect both: if the catch is cracked or has lost its spring tension, replace the catch. If the strike is bent, cracked, or missing, replace the strike. Since the kit includes both catches and strikes, you have everything needed for a complete repair. When in doubt, replacing both ensures the full latch system is renewed. My dryer will not start even after replacing the door catch — what else could it be? If the dryer still will not start after the catch is replaced, the door switch may also need to be tested. The door switch is the electrical component that the door catch activates when the door closes — if the switch itself is failed, replacing the catch alone will not restore function. Test the door switch (3406105 for most Whirlpool-family models) with a multimeter for continuity in both the open and closed positions. If the switch reads open in both positions or closed in both positions, it has failed and needs replacement. How is the 279570 different from the W11429587 dryer door catch? The 279570 is the door catch kit for older Whirlpool-family dryers — it includes multiple catches of different tensions and metal strikes because it covers a wide range of older models. The W11429587 is a single snap-in door catch for newer Whirlpool-family dryers (Cabrio and newer platform models). If your dryer is a newer model with a snap-in catch slot rather than a screw-mounted catch and strike, you likely need the W11429587. Verify your model number to confirm which part is correct. Is this a Genuine OEM or aftermarket part? This is a Genuine OEM kit manufactured by Whirlpool to factory specifications. It is the exact same door catch and strike kit supplied by Whirlpool for compatible dryer service repairs — guaranteed fit, materials, and performance. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

W11676494 Dryer Genuine OEM Knob Replaces Part Numbers: W11676494, W10215799, AP7215412, .

Read more less

XPARTCO 12138200000320 Dryer Door Catch The XPARTCO 12138200000320 is an aftermarket replacement dryer door catch compatible with select Midea and Insignia dryers. The door catch is a small plastic spring-clip mechanism mounted on the dryer door that snaps over the door strike o12138200000320 n the cabinet opening to hold the door firmly closed during operation. When the door is closed and latched, the door switch is activated — signaling the control board that it is safe to run. When the catch breaks, cracks, or loses its spring tension, the door will not stay closed, the door switch will not activate properly, and the dryer will either not start or will stop mid-cycle. This is a snap-in replacement catch — the color or exact finish may vary by production run. It directly replaces AP7152622 and PS18161385. Sold individually. Installs in under 5 minutes — no tools required in most cases. Quick Answer The XPARTCO 12138200000320 Dryer Door Catch fixes Midea and Insignia dryers where the door won't stay closed, pops open during a cycle, or where the dryer won't start because the door switch isn't being activated. Snap-in installation — no tools required, installs in under 5 minutes. Sold individually. Replaces AP7152622, PS18161385. Common Problems This Part Fixes Dryer door will not stay closed during the drying cycle Door pops open mid-cycle, stopping the dryer Dryer will not start — door switch not being activated by a worn or broken catch Door feels loose or does not click shut firmly when closed Door catch visibly cracked, broken, or missing Dryer requires the door to be held or pushed to stay running Replaces Part Numbers This door catch directly replaces the following part numbers: 12138200000320, AP7152622, PS18161385. Contact our support team with your model number if you need confirmation before ordering. Compatibility This door catch is compatible with select dryers from the following brands: Midea dryers (gas and electric — select models) Insignia dryers (select models) Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Holds the dryer door closed and activates the door switch so the dryer can run safely Snap-in installation — no tools required in most cases; installs in under 5 minutes Durable plastic construction — designed to withstand repeated opening and closing Sold individually — one door catch per order Replaces AP7152622 and PS18161385 Aftermarket replacement built to OEM-equivalent quality standards Product Specifications Part Number 12138200000320 Part Type Dryer Door Catch (Door Latch Clip) Condition Aftermarket Replacement Application Gas and Electric Dryers Material Plastic Installation Snap-in — no tools required Sold As Single door catch Compatible Brands Midea, Insignia Installation Notes ⚠️ Unplug Dryer Before Starting Disconnect power before beginning. Open the dryer door and locate the old door catch — it is a small plastic clip mounted on the inside of the door or on the cabinet opening around the door. Press the tabs on the old catch to release it from its mounting slot and pull it free. Note the orientation before removing. Insert the new 12138200000320 catch into the slot in the same orientation and press firmly until it snaps into place. Close the door to confirm it latches securely. Restore power and run a short cycle to verify the door stays closed and the dryer operates normally. Tools needed: None in most cases; a small flat-head screwdriver may help with removal. Frequently Asked Questions What dryers is the 12138200000320 compatible with? The 12138200000320 door catch is used on select Midea and Insignia dryer models. Insignia is a Best Buy house brand whose appliances are manufactured by Midea. Always verify your exact model number before ordering to confirm this catch fits your dryer's door latch assembly. Why won't my dryer start even though I'm closing the door? If the door catch is broken or worn, the door may not be engaging the door switch firmly enough to signal the control board that the door is closed. Most dryers will not run unless the door switch is fully activated. Replacing the 12138200000320 catch restores the firm snap needed to trigger the switch. If replacing the catch does not resolve the start issue, the door switch itself may also need to be checked. Do I need to replace the door strike as well? Not necessarily. In most cases only the door catch (the spring-clip on the door) needs replacement. The door strike (the post or tab on the cabinet that the catch snaps onto) is typically more durable. Inspect the strike for cracks or breakage before ordering — if it is intact, just the 12138200000320 catch is all you need. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Midea OEM part, but is manufactured from durable plastic to match the dimensions and function of the original 12138200000320 door catch. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

4681EA2001T (OE) Washer Drain Pump Motor The 4681EA2001T is an OE (Original Equipment) drain pump motor for LG and select Kenmore Elite front-load and top-load washers. At the end of each wash and rinse cycle, this pump is what forces water out of the tub and through the drain hose, clearing the way for the next fill and letting clothes come out free of excess water so the drying process can move faster. An internal impeller does the actual pumping work as the motor spins it. Rated 120–127V, 60Hz, 85W, 1.4A, with a flow rate of approximately 45L/min. This part is the motor and pump assembly only — it's designed to reuse your original pump housing rather than replace it, and it includes the pump impeller as part of the assembly. The design was updated in April 2025 to use a gray pump motor housing in place of the earlier black housing; either version installs and functions the same way. A failing drain pump typically shows up as the washer not draining, unusual or excessive noise during the drain portion of the cycle, an error code indicating a drain pump fault, or water leaking from the pump area and potentially damaging the surrounding floor. It directly replaces 1468049, 2003273, 4681EA1007D, 4681EA1007G, 4681EA2001D, 4681EA2001N, 4681EA2001U, AP4437652, AP5328388, DP040-038, EAP3523278, EAP3579318, LP2001T, and 5214FR4006L. Quick Answer The 4681EA2001T (OE) Washer Drain Pump Motor fixes LG and select Kenmore Elite front-load and top-load washers that won't drain, make unusual or loud noise during the drain cycle, show a drain-related error code, or leak water near the pump. 120–127V, 60Hz, 85W, 1.4A, 45L/min. Reuses your original pump housing; includes the impeller. Replaces 1468049, 2003273, 4681EA1007D, 4681EA1007G, 4681EA2001D, 4681EA2001N, 4681EA2001U, AP4437652, AP5328388, DP040-038, EAP3523278, EAP3579318, LP2001T, 5214FR4006L. Before replacing, clear any clogs in the drain path and check the pump filter and coin trap — these are common causes of "won't drain" symptoms that don't require a new motor. Common Problems This Part Fixes Washer not draining at the end of the cycle Unusual or excessive noise during the drain portion of the cycle Drain-related error code (such as OE) displayed on the control panel Water leaking from around the pump, potentially damaging the surrounding floor Washer failing or stalling mid-cycle due to a drain fault Longer-than-normal drain times Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer drain pump motor directly replaces the following OEM and cross-reference part numbers: 4681EA2001T, 4681EA1007G, 2003273, 4681EA1007D, 4681EA2001D, 4681EA2001N, 4681EA2001U, DP040-038, ALG51292, AH3579318, EA3579318, PD00001722, EAP3579318, AP5328388, PS3579318. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This drain pump motor is compatible with select LG front-load and top-load washers, and also fits select Kenmore Elite washers built on the LG platform, including model numbers such as: WM2101HW, WM2250CW, WM2277HB, WM2350HRC, WM2350HWC, WM2450HRA, WM2455HG, WM2487HRMA WM2550HRCA, WM2550HWCA, WM2650HRA, WM2650HWA, WM2655HVA WM3001HWA, WM3070HRA, WM3070HWA, WM3150HVC, WM3150HWC, WM3270CW WM3360HRCA, WM3360HVCA, WM3360HWCA, WM3431HS, WM3470HVA, WM3470HWA WM3550HVCA, WM3550HWCA, WM3770HVA, WM3885HCCA, WM3885HWCA, WM3987HW WM4070HVA, WM8000HVA, WM8000HWA GCW1069CS, GCW1069QS, LSWF388HVS, CW2079CWD, CW2079CWN, F1201FD, F1201FD1, F1201FDP, F1201FDP1, F1216 Kenmore Elite 79641072310 Note: This part reuses your original pump housing — it is not a complete pump-and-housing assembly. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features OE (Original Equipment) part — same design and performance standards as the original factory part Pump motor and impeller assembly — designed to reuse your original pump housing Resolves "won't drain," "unusual noise during drain," "drain error code," and "leaking near the pump" symptoms Rated 120–127V, 60Hz, 85W, 1.4A, approximately 45L/min flow rate Updated design (April 2025) uses a gray motor housing in place of the earlier black housing — both function identically Direct drop-in replacement for the original motor and impeller Replaces 1468049, 2003273, 4681EA1007D, 4681EA1007G, 4681EA2001D, 4681EA2001N, 4681EA2001U, AP4437652, AP5328388, DP040-038, EAP3523278, EAP3579318, LP2001T, and 5214FR4006L Compatible with LG and select Kenmore Elite front-load and top-load washers Product Specifications Part Number 4681EA2001T Designation OE (Original Equipment) Part Type Washer Drain Pump Motor Brand LG Application Front-Load and Top-Load Washers Voltage 120–127V Frequency 60 Hz Wattage 85 W Amperage 1.4 A Flow Rate Approx. 45 L/min Housing Reuses original pump housing; motor housing color varies by production date (black or gray) Included Components Motor, pump impeller Repair Difficulty Medium — 30 to 60 minutes Quantity 1 drain pump motor Compatible Brands LG, Kenmore Elite Installation Notes ⚠️ Unplug Washer And Shut Off Water Before Starting — Check For A Simple Clog First Before replacing the motor, clear any clogs in the drain path and check the pump filter and coin trap (if your model has one) — these are common, simple causes of "won't drain" symptoms that don't require a new motor. Once you've confirmed the motor needs replacing, disconnect power at the outlet and shut off the water supply. Lay towels or rags down in front of the washer. Wear work gloves. On front-load models, remove the detergent drawer, then remove the retaining wire and spring around the door gasket using a spring expansion tool or vise grips, and pull the gasket out of its groove at the front of the washer to access the pump area. Photograph the wiring and hose connections before disconnecting anything. Disconnect the wire connector from the old motor, remove the mounting screws or clips securing it to the pump housing, and separate the motor from the housing — this part is designed to reuse your original housing, so keep it intact for the new motor. Attach the new 4681EA2001T motor and impeller to your original housing, reconnect the wire connector, and secure the mounting hardware. Reinstall the door gasket into its groove, then reinstall the retaining wire and spring, and reattach the detergent drawer. Restore the water supply and power, then run a test cycle to confirm the washer drains normally with no leaks or unusual noise. Tools needed: Phillips screwdriver, locking pliers, needle-nose pliers, small flathead screwdriver, spring expansion tool (front-load models), towels, work gloves. Frequently Asked Questions Does this include a new pump housing, or just the motor? Just the motor and impeller — this part is designed to reuse your original pump housing rather than replace it. When you remove the old motor, keep the housing intact and attach the new motor to it. If your housing itself is cracked or damaged, that's a separate part. My washer isn't draining. Do I need to replace the motor, or could it be something simpler? Check for a simpler cause first. Clear any clogs in the drain path, and inspect the pump filter and coin trap if your model has one — foreign objects and debris commonly cause a washer to stop draining without the motor itself having failed. If the drain path and filter are clear and the washer still won't drain, or the motor makes unusual noise or won't run, replacement is the correct next step. The new pump I received has a gray housing but my old one was black. Is that correct? Yes. LG updated the design in April 2025 to use a gray motor housing in place of the earlier black housing. Both versions install the same way and function identically — the color change doesn't affect fit or performance. Is this a genuine OEM part? This is an OE (Original Equipment) part. OE (Original Equipment) parts are produced to the same design and performance standards as the original factory part, but they are not sold under the appliance brand's OEM label. They provide the same fit and function as the OEM part at a more affordable price. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ OE (Original Equipment) Quality ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

5300622032 Genuine OEM Dryer Heater Restring - Compatible with Frigidaire, Electrolux, Kenmore Product Description Restore optimal drying performance with the 5300622032 Genuine OEM Dryer Heater Restring. This authentic Frigidaire-manufactured heating element restring coil is designed for select Frigidaire, Electrolux, Gibson, Kelvinator, Tappan, White Westinghouse, and Kenmore dryers, generating heat to efficiently dry clothes. Built for durability and precise fit, it addresses issues like no heat or insufficient heat. Note: Includes one heating element restring coil with 1/4" terminals (4600 watts, 240 volts). Does not include heater housing insulators (131472100) or terminal block (3202786). Disconnect power before installation. Verify compatibility with your dryer model. Replaces part numbers: 5300622032, 08015672, 3202787, 3281114, AH451031, DE335, EA451031, NQ00622032, Q000622032, Q622032, TJ90DE335, WQ622032, PD00000126, EAP451031, AP2135127, PS451031. Compatibility: Compatible with models including but not limited to: Frigidaire: FDE646GES0, FDE747GES0, FDE847GES0, F31C336ES0, F31C436ES0 Gibson: GSE746RFS0, GSE746RFS1, GDE336RES1, GDE546RES0 Tappan: TDE336RED0, TDE546REW0 Kenmore, Electrolux, Kelvinator, White Westinghouse: (select models, verify compatibility) Verify your model number or contact our support team for assistance. Key Features: ✅ Brand and Models Compatibility: Fits select Frigidaire, Electrolux, Gibson, Kelvinator, Tappan, White Westinghouse, and Kenmore dryers. 🔧 Specifications: Genuine OEM heating element restring coil, 1/4" terminals, 4600 watts, 240 volts. 💪 Reliable Performance: Authentic Frigidaire part ensures efficient heat generation and long-lasting operation. 🛠️ Easy Installation: Requires screwdriver, pliers, and nut driver; typically installed in 30–45 minutes. 🛡️ Effective Fixes: Resolves no heat or insufficient heat in the dryer. Product Specification Part Number: 5300622032 Component Type: Dryer heating element restring coil Material: Metal alloy coil Electrical Rating: 4600 watts, 240 volts Mounting: Fits within existing heater housing, screw-mounted Operating Conditions: Suitable for household dryer environments Compliance: UL listed, Prop 65 warning for California Installation Notes: Safety First: Disconnect the dryer from the power source before installation. Shop for high-quality appliance parts with a 30-day return policy. Keep your dryer heating efficiently today! Add to cart now for a reliable fix!

Read more less

W10169881 Dryer Genuine OEM Thermostat Kit Description: This Dryer thermostat kit is an OEM replacement part responsible for ensuring the safety and temperature regulation of the dryer. The high-limit thermostat serves as a critical safety device that monitors and regulates the temperature inside the dryer. When the temperature rises to a level beyond the safe operating range, the high-limit thermostat interrupts the flow of electricity to the heating element. The thermal cut-out fuse, included in this kit, offers an additional layer of protection by disconnecting power to the heating element if it detects excessively high temperatures. Replaces Part Numbers: W10169881, 1455409, AH1964653, EA1964653, AP4316800, PS1964653.    California Residents only WARNING: California’s Proposition 65

Read more less