Search results for "microwave turntable motor"

5304523741 Refrigerator Genuine OEM Evaporator Fan Motor – Compatible with Frigidaire, Electrolux, and Kenmore Refrigerators Product Description Keep your refrigerator cooling efficiently with the 5304523741 Refrigerator Genuine OEM Evaporator Fan Motor. This factory-approved replacement circulates cold air from the evaporator throughout the refrigerator and freezer compartments. A failing fan motor can cause uneven temperatures, frost buildup, or warm sections in your fridge. Installing this genuine OEM part ensures quiet, dependable air circulation and consistent cooling performance. Replaces Part Numbers 5304523741, AP6983831, EAP12746805, 4960926, PD00067011, PS12746805. Compatibility This genuine OEM fan motor fits select Frigidaire, Electrolux, and Kenmore refrigerators. Example compatible models include (but are not limited to): Frigidaire FFSS2615TS0, Electrolux LFHB2751TF, and Kenmore 253.70313214. Always verify your refrigerator’s model number before ordering. Contact our support team if you’re unsure. ✅ Key Features 🔄 Genuine OEM Replacement – Factory-approved motor for reliable cooling performance ❄️ Efficient Air Circulation – Distributes cold air evenly throughout the compartments 💰 Energy-Efficient Operation – Restores temperature consistency and reduces compressor strain 🛠️ DIY Friendly – Direct-fit replacement installs in minutes 🛡️ Fixes Common Issues – Solves warm freezer, frost buildup, or noisy fan motor problems 📐 Product Specification Part Number: 5304523741 Component Type: Refrigerator Evaporator Fan Motor Material: Metal and high-temperature plastic housing Mounting: Direct-fit replacement in freezer compartment Operating Conditions: Designed for continuous low-temperature operation Compliance: Genuine OEM certified 🛠️ Installation Notes Tools Needed: Phillips screwdriver, nut driver ⚠️ Safety First: Always unplug the refrigerator before servicing to prevent electrical shock. Steps: Disconnect power and remove freezer shelves and back panel. Locate and disconnect the wiring harness from the old fan motor. Remove mounting screws and take out the old motor and fan blade. Transfer the fan blade (if required) to the new 5304523741 motor. Mount the new motor, reconnect wiring, and reinstall back panel. Restore power and confirm even cooling and quiet operation. ⏱️ Time Required: 20–30 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders 🧊 Genuine OEM Replacement Part 🔄 30-Day Return Policy Keep your refrigerator running at peak performance — Add to Cart Now for a genuine, factory-approved repair!

Read more less

809069207 Refrigerator Genuine OEM Evaporator Fan Motor – Compatible with Frigidaire, Electrolux, and Kenmore Refrigerators Product Description Restore powerful and consistent cooling with the 809069207 Refrigerator Genuine OEM Evaporator Fan Motor. This factory-approved motor circulates cold air throughout the refrigerator and freezer compartments, ensuring even temperature distribution. A failing fan motor can cause warm spots, frost buildup, poor cooling, or unusual noises. Replacing it with this Genuine OEM part ensures dependable performance and the same airflow efficiency your appliance had when new. Replaces Part Numbers 809069207, PD00064424, EAP12705983, AP6834878, PS12705983. Compatibility This Genuine OEM evaporator fan motor fits select Frigidaire, Electrolux, and Kenmore refrigerators. Example compatible models include (but are not limited to):Frigidaire FFHS2622MB3, FFSS2615TS0, Electrolux EI23CS55GS1, and Kenmore 253.7031321A. Always verify your refrigerator’s model number before ordering. Contact our support team if you’re unsure. ✅ Key Features 🧩 Genuine OEM Replacement – Factory-certified for perfect fit and long-lasting performance ❄️ Restores Air Circulation – Ensures even cooling in fresh food and freezer sections 🔇 Quiet Motor Operation – Balanced OEM motor design lowers noise and vibration 💪 High Durability – Built with premium materials for extended service life 🛡️ Fixes Common Issues – Solves poor cooling, frost buildup, noisy fan, or warm temperatures 📐 Product Specification Part Number: 809069207 Component Type: Refrigerator Evaporator Fan Motor Material: Reinforced plastic fan housing with factory motor Voltage: 115V AC (model dependent) Mounting: Direct-fit motor mounted behind freezer interior panel Compliance: Genuine OEM certified 🛠️ Installation Notes Tools Needed: Phillips screwdriver, nut driver ⚠️ Safety First: Always unplug the refrigerator before servicing to avoid electrical shock. Steps: Disconnect power and remove freezer shelves and panels. Locate the evaporator fan assembly. Disconnect the wiring harness and remove the old motor. Install the new 809069207 motor in the same location. Reassemble interior panels and restore power. Allow several minutes for airflow to stabilize. ⏱️ Time Required: 20–30 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Genuine OEM Replacement Part 🔄 30-Day Return Policy Restore powerful, even cooling — Add to Cart Now for a factory-quality repair!

Read more less

WR60X25858 Freezer Genuine OEM Evaporator Fan Motor The WR60X25858 is a genuine GE OEM freezer evaporator fan motor for GE refrigerators, and also fits select Hotpoint, Haier, Monogram, Café, Profile, and Kenmore models. Located in the freezer compartment, this motor circulates air across the evaporator coil and out into the freezer and, on many models, the fresh food compartment, drawing heat out of the air to maintain consistent, efficient cooling throughout the appliance. Rated 13.6V DC, 0.23 amps, with fan dimensions of approximately 4.5" x 4.5" and a wiring harness and plug extending about 8.25" from the frame. Common causes of failure include worn motor bearings or electrical failure over time. Symptoms of a failing evaporator fan motor include the freezer failing to cool properly and warming up, insufficient airflow, excessive frost buildup, higher-than-normal freezer temperatures, or unusual noise — often caused by frost or ice rubbing against the fan blade as it turns. It directly replaces 239D1371P002, 3033253, 4931166, U11P14MS7AA3-57A61, WR60X10340, AGE29632, AP6891698, EAP12727431, EAP7320382, PD00054264, PS12727431. Quick Answer The WR60X25858 Freezer Genuine OEM Evaporator Fan Motor fixes GE, Hotpoint, Haier, Monogram, Café, Profile, and Kenmore refrigerators with a freezer that's warming up, insufficient airflow, excessive frost, or unusual noise from the fan area. 13.6V DC, 0.23A, ~4.5" x 4.5", 8.25" harness. Replaces 239D1371P002, 3033253, 4931166, AP5669723, AP6891698, EAP12727431, EAP7320382, PS12727431, PS7320382, U11P14MS7AA3-57A61, WR60X10340, AGE29632. If your freezer isn't cold, check the evaporator fan first — but while you're in there, cleaning frost or ice off the fan blade and vacuuming the condenser coils are worthwhile companion steps. Common Problems This Part Fixes Freezer not cooling properly, warming up Insufficient airflow through the freezer compartment Excessive frost buildup Higher-than-normal freezer temperatures Unusual noise from the fan area, including frost or ice rubbing on the blade Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This freezer evaporator fan motor directly replaces the following OEM and cross-reference part numbers: 239D1371P002, 3033253, 4931166, U11P14MS7AA3-57A61, WR60X10340, AGE29632, AP6891698, EAP12727431, EAP7320382, PD00054264, PS12727431 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This evaporator fan motor is compatible with select GE refrigerators, and also fits select Hotpoint, Haier, Monogram, Café, Profile, and Kenmore refrigerators built on the GE platform, including model numbers such as DFE29JSDFSS and DFE29JGDAWW. Note: GE uses several different evaporator fan motors across its refrigerator lineup, including WR60X26866 and WR60X26033 for other models. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure which motor your refrigerator needs. Key Features Genuine GE OEM part — factory-specified motor design and airflow rating Circulates air across the evaporator coil to draw heat out and cool the freezer Resolves "freezer warming up," "insufficient airflow," "excessive frost," and "unusual noise" symptoms Rated 13.6V DC, 0.23 amps Approximately 4.5" x 4.5", with an 8.25" wiring harness and plug Direct drop-in replacement matching the original mounting and connections Replaces 239D1371P002, 3033253, 4931166, U11P14MS7AA3-57A61, WR60X10340, AGE29632, AP6891698, EAP12727431, EAP7320382, PD00054264, PS12727431 Compatible with GE, Hotpoint, Haier, Monogram, Café, Profile, and Kenmore refrigerators Genuine OEM replacement — guaranteed fit, materials, and performance DIY-friendly repair, typically 15 to 30 minutes Product Specifications Part Number WR60X25858 Part Type Freezer Evaporator Fan Motor Condition Genuine OEM Brand GE Location Freezer compartment Voltage 13.6V DC Amperage 0.23 A Fan Dimensions Approx. 4.5" x 4.5" Harness/Plug Length Approx. 8.25" from frame Repair Difficulty Easy — 15 to 30 minutes Quantity 1 fan motor Compatible Brands GE, Hotpoint, Haier, Monogram, Café, Profile, Kenmore Installation Notes ⚠️ Unplug Refrigerator Before Starting — Clear Any Frost Or Ice From The Fan Area Unplug the refrigerator and safely store any food that could spoil while the power is off. Wear work gloves. Locate the evaporator fan motor in the freezer compartment, typically behind an interior panel covering the evaporator coil assembly. If there's noticeable frost or ice buildup around the fan or coil, allow it to fully defrost before continuing — restricted airflow from ice is a common contributor to fan motor strain and noise. Remove the panel to access the fan motor, then disconnect the wiring harness from the old motor. Remove the mounting screws or clips securing the old motor and pull it free, along with the fan blade if it doesn't transfer separately. Install the new WR60X25858 in the same position, reconnect the wiring harness fully, and secure the mounting hardware. Reinstall the interior panel. While you're in this area, vacuuming out any accessible condenser coils is a good complementary maintenance step. Restore power and monitor the freezer's temperature over the next 24 hours to confirm normal, quiet operation and consistent cooling. Tools needed: Phillips screwdriver, work gloves. Frequently Asked Questions My freezer isn't cold anymore. Is this the part I need? Yes, this is one of the most common causes of a freezer that won't cool. One customer specifically reached out after their freezer wasn't cold, watched a diagnostic video explaining the evaporator fan's role, and confirmed this motor was the cause before ordering the replacement. I hear a strange noise from inside my freezer. Could this be the fan motor? Yes, this is a well-documented symptom. Noise often occurs when the fan motor itself is wearing out, or when frost or ice has built up enough to rub against the spinning fan blade. Clearing any ice buildup before replacing the motor helps you confirm whether the noise was from ice contact or the motor itself. Should I do anything else while I have the freezer open for this repair? It's a good opportunity to check for and clear any frost or ice buildup around the fan and coil area, since restricted airflow can contribute to fan strain. One customer also vacuumed out the condenser coils during the same repair, which is a reasonable companion maintenance step while everything is accessible. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by GE to factory specifications — guaranteed fit, materials, and performance. It matches the original motor design, voltage, and connection type of the evaporator fan motor originally installed in your refrigerator. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

WB18X35517 Microwave Genuine OEM Thermostat Replaces Part Numbers: WB18X35517, AP6990372, PS16219519   California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

DE47-20034A Microwave Genuine High Limit Thermostat Thermal cutout. High limit thermostat. Open for continuity at room temperature, closes when it gets hot. Fits Samsung over counter microwaves. Replaces Part Numbers:DE47-20034A, AP4219754, PS4226431.  California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

XPARTCO W11520384 Microwave Light Bulb The XPARTCO W11520384 is an aftermarket replacement halogen light bulb for Whirlpool, Maytag, and Amana microwaves and microwave/hood combination units. This G9-base halogen bulb provides the bright, reliable interior illumination that lets you see food clearly while cooking, making it easier to monitor progress and avoid accidents from working in a dim cavity. Rated 120V, 40W, 60Hz. Over time, halogen bulbs burn out from normal use, or can dim and fail prematurely if the glass envelope is touched with bare fingers during installation, since skin oils can cause uneven heating and shorten the bulb's life. A failed bulb produces a straightforward and unmistakable symptom: reduced visibility or complete darkness inside the microwave cavity during use. It directly replaces 4981936, EAP17215402, FIX17215402, OEM28869642, PS17215402, AWP861603, and PD00089571. Quick Answer The XPARTCO W11520384 Microwave Light Bulb fixes Whirlpool, Maytag, and Amana microwaves and microwave/hood combos with a dim or completely burned-out interior light. G9 base, 120V, 40W, 60Hz halogen bulb. Replaces 4981936, EAP17215402, FIX17215402, OEM28869642, PS17215402, AWP861603, PD00089571. Avoid touching the glass with bare fingers during installation — skin oils can cause the bulb to fail prematurely or heat unevenly. Common Problems This Part Fixes Microwave interior light burned out completely Microwave interior light dim or flickering Difficulty monitoring food while cooking due to poor interior lighting Light that worked intermittently before failing entirely Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This microwave light bulb directly replaces the following OEM and cross-reference part numbers: W11520384, 4981936, EAP17215402, FIX17215402, AP7217410, AWP861603, OEM21652239, PD00089571, PS17215402 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This light bulb is compatible with select Whirlpool microwaves and microwave/hood combos, and also fits select Maytag and Amana models built on the same platform, including model numbers such as: WMH31017HB09, WMH31017HS11, WMH31017HW10, YWMH31017HB05, YWMH31017HZ08, YWMH31017HZ09, YWMH31017HS09 WMH32519HB08, WMH32519HT10, WMH32519HV09, WMH32519HW08, WMH32519HZ09 WMMS3130RB00, YWMMS3130RB00, YWMMS3130RZ00 UMV1170LB04, UMV1170LS02, UMV1170LW03 MMV1175JB01, MMV1175JB02, YMMV1175JZ02 YMMMS4230PZ01, YAMV2307PFW08, YAMV2307PFW11 Note: Always verify your full model number before ordering, since not all Whirlpool microwaves use this same bulb type and base. Contact our support team with your model number if you're unsure. Key Features Aftermarket replacement halogen light bulb — bright, reliable interior illumination Resolves "burned out light" and "dim interior lighting" symptoms G9 base, 120V, 40W, 60Hz Direct drop-in replacement — no tools required on most models Replaces 4981936, EAP17215402, FIX17215402, OEM28869642, PS17215402, AWP861603, and PD00089571 Compatible with Whirlpool, Maytag, and Amana microwaves and microwave/hood combos Aftermarket replacement built to OEM-equivalent quality standards Product Specifications Part Number W11520384 OEM Part Number W11520384 Part Type Microwave Halogen Light Bulb Condition Aftermarket Replacement Bulb Type Halogen Base G9 Voltage 120V Wattage 40 W Frequency 60 Hz Weight 0.02 lbs Repair Difficulty Very Easy — no tools required Quantity 1 light bulb Compatible Brands Whirlpool, Maytag, Amana Installation Notes ⚠️ Unplug Microwave Before Starting — Let The Old Bulb Cool, And Don't Touch The New Glass With Bare Fingers Disconnect power at the outlet before beginning, and if the microwave was recently used, allow the old bulb time to cool completely before touching it. Wear work gloves. Locate the light bulb cover or access panel inside the microwave cavity, or behind an exterior panel depending on your model, and remove it per your appliance's instructions. Remove the old bulb from its socket. When handling the new W11520384, avoid touching the glass envelope directly with bare fingers — use a clean cloth or tissue if needed, since skin oils can transfer to the glass and cause the bulb to heat unevenly or fail prematurely. Insert the new bulb into the socket, making sure it's seated fully and correctly. Reinstall the cover or access panel. Restore power and turn on the microwave light to confirm normal, bright illumination. Tools needed: none, or a screwdriver if your model's bulb is behind a screwed access panel. Frequently Asked Questions Why shouldn't I touch the new bulb with my bare fingers? Halogen bulbs are sensitive to skin oils left on the glass envelope. If oils from your fingers transfer to the glass during installation, they can cause the bulb to heat unevenly when it's powered on, which can shorten its lifespan or lead to premature failure. Handling the bulb with a clean cloth or tissue avoids this issue entirely. My microwave light flickers before going out completely. Is that normal before a bulb fails? Yes, flickering or dimming is a common warning sign that a halogen bulb is nearing the end of its life, often shortly before it burns out completely. If you notice this happening, it's a good time to have a replacement bulb on hand. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured to match the G9 base, wattage, and voltage rating of the original W11520384 halogen bulb used in compatible Whirlpool, Maytag, and Amana microwaves. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPMTC-180 Microwave Thermal Cut-Off Fuse 180℃ (356°F) – Normally Closed – Universal Microwave Safety Cutoff Product Description Protect your microwave from extreme overheating with the XPMTC-180 Microwave Thermal Cut-Off Fuse 180℃ (356°F), Normally Closed. This high-temperature safety device is designed to remain closed (conductive) during normal operation and open permanently when internal temperatures exceed 180℃, immediately cutting power to prevent serious damage or fire risk. A tripped thermal cut-off can cause the microwave to lose power or stop heating. Replacing it with the correctly rated NC fuse restores safe and reliable operation. Replaces Part Numbers XPMTC-180, MTC-180, Microwave Thermal Fuse 180C NC, 356F Normally Closed Thermal Cutoff, WB24X29270, 4586233, PD00045446, EAP12170419, KSD1 BR1 180, AP6262395, PS12170419, 6930W1A003X, 1365203, AH3530468, EA3530468, PD00001857, AP4443816, PS3530468. Compatibility This normally closed microwave thermal cut-off fuse is compatible with many GE, Whirlpool, Samsung, LG, Frigidaire, Panasonic, Sharp, and Kenmore microwave ovens that require a 180℃ (356°F) NC thermal cutoff. Commonly used near the magnetron, high-heat zones, or cavity protection points. Always verify temperature rating and contact type before ordering.Contact our support team if you’re unsure. 🔍 What’s the Difference Between NC and NO Thermal Cut-Offs? Normally Closed (NC): Circuit is closed during normal operation and opens permanently when the rated temperature is reached.👉 Most microwave thermal cut-offs are NC. Normally Open (NO): Circuit is open during normal operation and closes only when overheated (used in limited designs). ⚠️ Installing the wrong type (NC vs NO) may cause the microwave not to run or fail to protect against overheating. ✅ Key Features 🔄 Aftermarket Replacement – Built to OEM-equivalent safety specifications 🌡️ 180℃ (356°F) Rating – Designed for high-temperature protection zones 🔁 Normally Closed (NC) – Conducts power during normal operation 🛡️ Critical Safety Component – Prevents overheating and fire hazards 💰 Cost-Effective Repair – Affordable alternative to OEM thermal cut-offs 📐 Product Specification Part Number: XPMTC-180 Component Type: Microwave Thermal Cut-Off Fuse Temperature Rating: 180℃ (356°F) Contact Type: Normally Closed (NC) Function: One-time safety cutoff Material: Heat-resistant metal body Application: Magnetron or high-heat cavity temperature protection Quality Level: Aftermarket replacement (not OEM) 🛠️ Installation Notes Tools Needed: Phillips screwdriver, insulated pliers ⚠️ Safety First:Unplug the microwave before servicing. Microwaves contain high-voltage components—allow capacitors to discharge before handling internal parts. Basic Steps: Disconnect microwave power. Remove the outer cabinet or access panel. Locate the thermal cut-off near the magnetron or high-heat area. Disconnect wiring and remove the failed fuse. Install the new XPMTC-180 (NC) thermal cut-off in the same position. Reassemble the microwave and restore power. Test operation. ⏱️ Time Required: 15–25 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Aftermarket Appliance Parts 🔄 30-Day Return Policy Restore microwave safety under extreme heat conditions — Add to Cart Now for a dependable, budget-friendly repair!

Read more less

W11414076 Genuine OEM Whirlpool Dishwasher Circulation Pump Motor Assembly The W11414076 is a Genuine OEM Whirlpool replacement circulation pump and motor assembly compatible with a wide range of Whirlpool, KitchenAid, Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, Kenmore, and Ikea dishwashers. The circulation pump is the heart of the wash system — it pressurizes and delivers water to the spray arms, driving the jets that blast food and residue off your dishes throughout the wash and rinse cycles. When the circulation pump fails, cleaning performance collapses: dishes come out dirty or unrinsed, water pressure at the spray arms drops, and the machine may make loud droning or grinding noises. This is a complete circulation pump and motor assembly. Common causes of failure include worn motor bearings (which produce a continuous drone that gets louder over time), deteriorated impellers, and seal breakdowns. As a Genuine OEM part manufactured by Whirlpool to factory specifications, the W11414076 is the current production part that supersedes W11122133. It also replaces AP6980104, EAP12745416, PS12745416, 4958907, and OEM20940317. Note: this assembly does not include the drain pump — your existing drain pump transfers over to the new assembly during installation. Installs in 45–90 minutes with basic hand tools (the dishwasher must be pulled out and laid on its back to access the pump). Quick Answer The W11414076 Genuine OEM Whirlpool Dishwasher Circulation Pump Motor Assembly fixes Whirlpool, KitchenAid, Maytag, Jenn-Air, and Amana dishwashers where dishes come out dirty or unrinsed, water pressure at the spray arms is weak, water pools in the tub, or the motor makes a loud droning/grinding noise. Complete circulation pump + motor assembly. Genuine OEM. Current part superseding W11122133; also replaces AP6980104, EAP12745416, PS12745416, 4958907, OEM20940317. Before ordering: if the motor runs but water is weak, try cleaning the impeller filter screen first — see the FAQ. Common Problems This Part Fixes Dishes coming out dirty or unrinsed — circulation pump not delivering water to the spray arms Weak water pressure at the spray arms — impeller worn or motor failing Loud droning noise that gets louder over time — worn motor bearings Grinding or unusual noise during operation Water retention/pooling in the bottom of the tub Leaks from the pump housing — seal breakdown Motor humming but spray arms barely turning Reduced cleaning performance overall Motor not running at all — failed pump motor windings Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This circulation pump motor assembly directly replaces the following OEM and cross-reference part numbers: W11414076, W11122133, AP6980104, EAP12745416, PS12745416, 4958907, OEM20940321, AWP45352, PD00070783 W11414076 is the current OEM production part superseding W11122133. Contact our support team with your model number if you need confirmation before ordering. Compatibility This circulation pump motor assembly is compatible with select dishwashers from the following brands: Whirlpool dishwashers — select models (verify with your parts diagram) KitchenAid dishwashers — select models Maytag dishwashers — select models Jenn-Air dishwashers — select models Amana dishwashers — select models Magic Chef dishwashers — select models Admiral dishwashers — select models Norge dishwashers — select models Roper dishwashers — select models Kenmore / Sears dishwashers — select Whirlpool-built models Ikea dishwashers — select Whirlpool-built models This assembly may comprise several parts — refer to your specific parts diagram to verify included items. Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Genuine OEM part manufactured by Whirlpool to factory specifications — guaranteed fit and performance Circulation pump and motor assembly — pressurizes and delivers water to the spray arms for effective cleaning and rinsing Resolves "dirty dishes," "weak water pressure," "loud droning motor," "grinding noise," and "water pooling" symptoms when caused by pump failure Addresses the common failure modes: worn motor bearings, deteriorated impellers, and seal breakdowns Current OEM production part — directly supersedes W11122133 Also replaces AP6980104, EAP12745416, PS12745416, 4958907, and OEM20940317 Motor separates from the pump case with 3 Torx screws — some customers replace only the motor if the pump case is fine Drain pump is not included — your existing drain pump transfers to the new assembly Compatible with Whirlpool, KitchenAid, Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, Kenmore, and Ikea dishwashers DIY repair — installs in 45–90 minutes with basic hand tools Product Specifications Part Number W11414076 Supersedes W11122133 Part Type Dishwasher Circulation Pump & Motor Assembly Condition Genuine OEM Application Dishwashers (Whirlpool platform) Function Delivers water to the spray arms for washing and rinsing Motor Attachment Separates from pump case with 3 Torx screws Drain Pump Not included — transfer your existing drain pump Location Bottom of dishwasher (access by laying unit on its back) Compatible Brands Whirlpool, KitchenAid, Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, Kenmore, Ikea Installation Notes ⚠️ Unplug Dishwasher and Shut Off Water Before Starting — Wear Work Gloves — Major Access Required Disconnect power at the breaker and shut off the water supply before beginning. Wear work gloves to protect your hands. This is a more involved repair because the circulation pump is on the bottom of the dishwasher. Throw the circuit breaker, remove the lower access panel, and open the electrical box to completely disconnect the electrical from the dishwasher. Disconnect the water supply line and the drain line. Remove the anchor screws securing the dishwasher to the counter, then pull the dishwasher out of the cabinet. Have a large towel ready — rotate the dishwasher and lay it on its back to access the pump on the bottom. Photograph everything before disconnecting. Disconnect all connections to the main circulation pump: the drain pump, the electrical connections, the leak-detection plate and circuit, and the water lines. Undo all clamps to the circulation pump. Remove the old circulation pump assembly. Transfer your existing drain pump to the new W11414076 assembly — it is not included. (If you're only replacing a noisy motor and the pump case is good, the motor separates from the case with 3 Torx screws and can be swapped on its own.) Install the new assembly, reconnect the drain pump, electrical connections, leak-detection plate, water lines, and all clamps, matching your photos. Stand the dishwasher back up, slide it into the cabinet, reconnect water/drain/electrical, and secure the anchor screws. Run a short test cycle and check for leaks. Note: use your dishwasher's onboard diagnostic function to confirm the pump was the issue — light/error codes vary by model, so check the quick guide that came with your specific dishwasher rather than relying on codes listed online for other models. Tools needed: Phillips screwdriver, Torx driver (T-set), nut driver, pliers, large towel, work gloves. Frequently Asked Questions The motor runs but water barely reaches the spray arms — do I definitely need a new pump? Maybe not — try this first, because it could save you the entire repair. On many KitchenAid/Whirlpool-platform dishwashers, there's a fine filter screen INSIDE the circulation pump on the impeller. This screen can clog with microplastics and fine food particles over time (sometimes after a surprisingly small number of wash cycles), which chokes off water flow even though the motor is running perfectly. The screen can look clean but still be blocked — a real-world test is to hold water in the mesh cup: if it holds water like a cup instead of draining freely, it's clogged. Cleaning it with a toothbrush restores full flow. To access it you do have to pull the pump (the same disassembly as replacing it, then 2 Torx screws to open the pump), so if you're already this far in, disassemble and inspect the screen BEFORE installing a new pump — you may find the old pump is perfectly good. Running a dishwasher-safe cleaning product through the machine first is also worth a try. My dishwasher motor is loud and getting louder — is that the pump? Yes, that's a classic sign of worn circulation pump motor bearings. The motor bearings wear out over time, and as they degrade they produce a continuous drone that steadily gets louder. Once the bearings have failed, the noise won't go away on its own and the motor should be replaced. On this assembly, the motor separates from the pump case with 3 Torx screws — some customers who only have a bearing/noise problem (and an otherwise good pump case) simply swap the motor and reuse the case. If you order the full assembly, you get both, and you can decide during the repair whether to swap just the motor or the whole thing. Does this come with the drain pump? No — the W11414076 is the circulation pump and motor assembly, and it does not include the drain pump. During installation, you'll transfer your existing drain pump from the old assembly to the new one (it detaches and reattaches). This is normal for this repair. If your drain pump is also failing (separate symptoms: won't drain, water left standing after the cycle), that's a different part you'd order separately. The circulation pump handles washing/spray pressure; the drain pump handles emptying the tub. What's the difference between W11414076 and W11122133? These are the same circulation pump assembly across production revisions. W11122133 was the earlier OEM part number, and W11414076 is the current production version that Whirlpool issued as its direct replacement. Both are physically and functionally interchangeable — if your dishwasher's parts diagram shows W11122133, the W11414076 is the correct current replacement, and this listing covers both. The cross-references AP6980104, PS12745416, and 4958907 are additional catalog identifiers for the same part. Is this a Genuine OEM or aftermarket part? This is a Genuine OEM part manufactured by Whirlpool to factory specifications. It is the exact same circulation pump and motor assembly installed in compatible Whirlpool, KitchenAid, Maytag, Jenn-Air, Amana, and Kenmore Whirlpool-built dishwashers from the factory — guaranteed fit, materials, and performance. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

WD26X25103 Genuine OEM GE Dishwasher Variable Wash Pump Kit The WD26X25103 is a genuine GE OEM variable wash pump kit for premium GE, Café, GE Profile, Monogram, Hotpoint, and Haier dishwashers. The wash pump is the heart of the cleaning system — it draws filtered water from the sump and drives it under pressure through the lower spray arm, the middle spray arm, and the upper wash manifold. What makes this a variable pump is its variable-speed motor: instead of running at one fixed speed, the control board modulates pump speed throughout the cycle, ramping pressure up for heavy soil and down for delicate loads, and shifting flow between spray zones. That is why a failing variable pump often produces uneven results — the bottom rack comes out clean while the top rack is barely wet. This is a complete kit, supplied with the circulation pump assembly and its integrated wiring harness, so you are not transferring connectors from the old unit. Typical failure modes include worn motor bearings that produce a loud humming or grinding during the wash portion of the cycle, a seized or debris-jammed impeller, a shaft seal that begins weeping water into the base pan and trips the flood switch, and electrical failure of the variable-speed motor windings. It directly replaces WD26X22789, AP6973120, PS12730515, and EAP12730515. This is a moderate DIY repair — most people budget 1–2 hours. Quick Answer The WD26X25103 Genuine OEM GE Variable Wash Pump Kit fixes GE, Café, GE Profile, Monogram, Hotpoint, and Haier dishwashers with dishes that come out dirty or gritty, a top rack that isn't getting wet, weak or no spray arm rotation, loud humming or grinding during the wash cycle, or water pooling in the base pan from a leaking pump seal. Variable-speed motor; kit includes pump assembly plus integrated wiring harness. Replaces WD26X22789, AP6973120, PS12730515, EAP12730515. Fits premium CDT865/CDT866, PDT845/PDT846/PDT855, and ZDT915/ZDT975 platforms — not the same pump as WD26X23258. Common Problems This Part Fixes Dishes not getting clean — food soil, grit, or film left behind after a full cycle Top rack not getting wet or not getting cleaned while the bottom rack washes normally Spray arms turning slowly or not turning at all — insufficient water pressure Loud humming, whining, or grinding noise during the wash portion of the cycle Dishwasher runs a full cycle quietly with no audible water circulation Water pooling in the base pan under the dishwasher from a leaking pump shaft seal Flood switch or leak sensor tripping and shutting the dishwasher down mid-cycle Cleaning performance that has gradually declined over months as bearings wear Pump motor humming but the impeller not turning — seized shaft or jammed impeller Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dishwasher variable wash pump kit directly replaces the following OEM and cross-reference part numbers: WD26X25103, WD26X22789, AGE25305, AP6973120, PD00054224, PS12730515, EAP12730515. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This variable wash pump kit is compatible with select premium built-in dishwashers from the following brands: GE and GE Profile dishwashers (PDT845, PDT846, and PDT855 series) Café dishwashers (CDT865 and CDT866 series) Monogram dishwashers (ZDT915 and ZDT975 series) Hotpoint dishwashers (select GE-built models) Haier dishwashers (select GE-platform models) Verified model numbers include: CDT865SSJ0SS, CDT865SSJ2SS, CDT865SMJ0DS, CDT865SMJ2DS, CDT866P2M4S1, CDT866P3M4D1, CDT866P4M4W2, PDT845SSJ0SS, PDT845SSJ2SS, PDT845SMJ0ES, PDT845SMJ2ES, PDT845SBL2TS, PDT845SBL3TS, PDT845SFL3DS, PDT846SSJ0SS, PDT846SSJ2SS, PDT846SMJ0ES, PDT846SMJ2ES, PDT855SSJ0SS, PDT855SSJ2SS, PDT855SMJ0ES, PDT855SMJ2ES, PDT855SIJ0II, PDT855SIJ2II, PDT855SBL2TS, PDT855SBL3TS, PDT855SFL3DS, ZDT915SSJ0SS, ZDT915SSJ2SS, ZDT915SIJ0II, ZDT915SIJ2II, ZDT915SPJ0SS, ZDT915SPJ2SS, ZDT975SSJ0SS, ZDT975SSJ2SS, ZDT975SIJ0II, ZDT975SIJ2II, ZDT975SPJ0SS, and ZDT975SPJ2SS. Note: GE uses several different circulation pumps across its dishwasher lineup, and they are NOT interchangeable. The WD26X25103 is the variable-speed pump used on premium CDT/PDT/ZDT platforms. It is not the same part as the WD26X23258 circulation pump (GDT695/PDT825 platforms) or the WD26X22518 pump (PDF820/GDT535/ADT521 platforms). Fitting the wrong pump can result in a physical mismatch at the sump or a harness that will not mate with your control board. Always verify your full model number — including the suffix — before ordering. Contact our support team with your model number if you're unsure. Key Features Genuine GE OEM part — factory-specified flow rate, impeller geometry, and motor control profile Variable-speed motor allows the control board to modulate wash pressure by cycle and soil level rather than running at one fixed speed Complete kit — includes the circulation pump assembly and integrated wiring harness, so no connectors need to be transferred from the old pump Drives water through the lower spray arm, middle spray arm, and upper wash manifold Resolves "dishes not clean," "top rack not getting wet," "spray arms not turning," "loud humming or grinding," and "water in the base pan" symptoms caused by pump failure Sealed shaft design protects the motor from sump water intrusion Direct drop-in replacement for the superseded WD26X22789 — no modifications required Serves GE Profile, Café, Monogram, Hotpoint, and Haier premium dishwasher platforms Replaces WD26X22789, AP6973120, PS12730515, and EAP12730515 Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number WD26X25103 Part Type Dishwasher Variable Wash Pump Kit (Circulation Pump) Condition Genuine OEM Brand GE Appliances Motor Type Variable speed Voltage 120V / 60 Hz Function Circulates water under pressure to the spray arms and upper wash manifold Kit Contents Wash pump assembly + integrated wiring harness Location Underneath the tub, mounted to the sump housing Connections 2 hose clamps + 2 electrical connections Supersedes WD26X22789 Repair Difficulty Moderate — 1 to 2 hours Quantity 1 pump kit Compatible Brands GE, GE Profile, Café, Monogram, Hotpoint, Haier Installation Notes ⚠️ Disconnect Power And Shut Off Water Before Starting Turn off the dishwasher's circuit breaker and close the hot water supply valve under the sink before beginning. Wear work gloves — the tub edges and undercarriage brackets are sharp. Before condemning the pump, run a quick check: remove the lower spray arm and filter assembly, clear any glass chips, seeds, or labels from the sump, and confirm the spray arm ports are not blocked. A clogged filter screen produces the same "dishes not clean" complaint as a failing pump and costs nothing to rule out. To replace the pump, first remove the two screws securing the dishwasher to the underside of the countertop (or to the adjacent cabinets), disconnect the water line and drain hose, and slide the unit out. Most technicians then lay the dishwasher on its front or on its back to reach the pump — put a towel down to protect the door and finish. Photograph the hose routing and wiring before disconnecting anything. Release the two hose clamps and separate the two electrical connections, then unlock the pump from the sump housing — it typically twists to release from a bayonet-style mount — and lift it out. Inspect the sump gasket and seat while the pump is off; replace the gasket if it is hardened, flattened, or nicked. Install the new WD26X25103 in the same orientation, twist to lock, reattach both hoses with their clamps, and reconnect the harness. Reinstall the dishwasher, restore water and power, then run a full cycle and check underneath for leaks before pushing the unit all the way back and reattaching the mounting screws. Tools needed: Phillips screwdriver, nut driver, pliers or hose clamp pliers, towel, work gloves. Frequently Asked Questions My top rack isn't getting clean but the bottom rack is fine. Is that the wash pump? It's the signature symptom of a weakening wash pump, yes — but check two cheaper things first. The upper wash manifold and the middle spray arm are fed last and at the lowest pressure, so they are the first zones to suffer when pump output drops. However, a clogged filter screen or a spray arm with blocked ports will starve the upper rack the same way. Pull the lower spray arm and filter, rinse them under hot water, poke a toothpick through any blocked spray ports, and run a cycle. If the top rack is still dry or dirty after that, the variable pump is losing pressure and should be replaced. What does "variable" mean on this pump, and does it matter? It matters a great deal. A variable-speed pump lets the control board change pump speed during the cycle — higher pressure for heavy soil, lower for delicate loads, and different speeds when directing flow to different spray zones. A fixed-speed pump cannot do that. This is why you cannot substitute a standard circulation pump from another GE platform even if it physically resembles this one: the control board expects a variable-speed motor and will not drive a fixed-speed unit correctly. The dishwasher is making a loud grinding noise. Do I need the whole pump? Not always — check for foreign objects first. Glass chips, fruit pits, bones, and hard plastic bits routinely get past the filter and rattle inside the pump housing or wedge against the impeller. Remove the filter assembly and inspect the sump thoroughly with a flashlight. If the sump is clean and the noise is a steady hum or grind that rises with the wash cycle, the pump's motor bearings are worn and the complete kit is the correct repair. Bearing noise does not improve on its own and usually precedes a shaft seal leak. I found water in the pan underneath the dishwasher. Could the pump cause that? Yes. When the pump's shaft seal wears out, it weeps water down onto the base pan during every wash cycle. GE dishwashers have a flood switch in that pan, so the machine will eventually detect the water and shut itself down mid-cycle or refuse to start. Before ordering, confirm the water is coming from the pump and not from a loose hose clamp, a cracked sump, or the door gasket — dry the pan completely, run a short cycle, and watch where the first drops appear. Does this kit include everything, or do I need to reuse parts from the old pump? The kit ships with the wash pump assembly and its integrated wiring harness, so you will not need to cut, splice, or transfer the electrical connector from your old pump. You will reuse your existing hoses and clamps. Inspect the sump gasket while the pump is out and replace it if it looks hardened, flattened, or nicked — a tired gasket is a common cause of a "new pump that still leaks." What's the difference between WD26X25103 and WD26X22789? They are the same pump across production revisions. WD26X22789 was the earlier number and WD26X25103 is the current GE part number that supersedes it. If your dishwasher's parts diagram shows WD26X22789, this listing is the correct replacement — order it with confidence. The additional cross-references (AP6973120, PS12730515, EAP12730515) are catalog identifiers used by various parts distributors for the same kit. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by GE to factory specifications — guaranteed fit, materials, and performance. It matches the original variable-speed motor profile, impeller geometry, flow rate, sump mounting interface, and harness connector of the pump originally installed in your dishwasher, which is important on this platform because the control board is calibrated to drive a variable-speed pump. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO DA97-15765C Refrigerator Condenser Fan Motor The XPARTCO DA97-15765C is an aftermarket replacement condenser fan motor assembly for Samsung French door refrigerators. This assembly includes both the motor and the fan blade together, and it lives in the compressor/machine compartment at the back or bottom of the refrigerator, where its job is to pull air across the condenser coils and compressor to carry heat away from the refrigeration system. That's a different job from an evaporator fan — this motor cools the mechanical side of the system rather than circulating cold air to your food, so a failing condenser fan tends to affect the whole refrigerator's cooling capacity rather than just one compartment. Rated 12V DC, 0.14A, 1.7W, running at approximately 1,120 RPM. On many Samsung models, a failed condenser fan motor triggers a 23C or 23E error code on the display, alongside symptoms like noticeable vibration or noise from the condenser area, elevated internal temperatures, or the over-temperature alarm sensor tripping. Common causes include normal wear on the motor bearings after prolonged use, blockages from dust and debris accumulation around the coils, or damage from moisture exposure. A fan blade that tries to spin but can't complete a full revolution, or that needs a manual nudge to keep turning, is a classic sign this assembly has started to fail. It directly replaces DA97-15765A, DA97-12842A, DA97-12842B, DA97-12842D, DA97-15765D, AP6001015, PS11733650, EAP11733650, DA31-00340A, RMF002ASSA, and 4959328. Quick Answer The XPARTCO DA97-15765C Refrigerator Condenser Fan Motor fixes Samsung French door refrigerators where the whole unit runs warm, the compressor area is noisy or vibrating, a 23C or 23E error code appears, or the over-temperature alarm trips. Includes motor and fan blade. 12V DC, 0.14A, 1.7W, ~1,120 RPM. Replaces DA97-15765A, DA97-12842A, DA97-12842B, DA97-12842D, DA97-15765D, AP6001015, PS11733650, EAP11733650, DA31-00340A, RMF002ASSA, 4959328. This cools the compressor and condenser coils — a different part and symptom pattern than an evaporator fan, which only affects internal air circulation to the food compartments. Common Problems This Part Fixes Both the fresh food and freezer compartments running warmer than normal at the same time 23C or 23E error code displayed on the control panel Noticeable vibration or unusual noise from the condenser/compressor area at the back or bottom of the cabinet Over-temperature alarm sensor tripping Fan blade that tries to spin but doesn't complete a full revolution Fan blade that stops spinning if not manually nudged to keep turning Refrigerator running constantly as the compressor struggles to keep up Excessive dust or debris buildup visible around the condenser coils and fan Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This refrigerator condenser fan motor assembly directly replaces the following OEM and cross-reference part numbers: DA97-15765C, DA97-15765A, DA97-15765D, DA97-12842A, DA97-12842B, DA97-12842D, AP6001015, PS11733650, EAP11733650, DA31-00340A, RMF002ASSA, 4959328, OEM18003054, ASM138992, PD00050574 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This condenser fan motor assembly is compatible with select Samsung French door refrigerators, including model numbers such as: RF220NCTABC, RF220NCTASG, RF220NCTASP, RF220NCTASR, RF220NCTAWW RF221NCTABC, RF221NCTASP, RF221NCTAWW RF22K9381SG F261BEAESR This assembly also fits many additional Samsung French door refrigerator models beyond those listed above. Note — condenser fan, not evaporator fan: This motor cools the compressor and condenser coils in the machine compartment at the back or bottom of the refrigerator. It is a completely different part from an evaporator fan motor (such as our DA31-00334C listing), which sits behind the freezer's rear panel and circulates cold air to the food compartments. It is also a different part family from our DA97-20025A condenser fan listing, which serves a different group of Samsung models. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure which fan motor your refrigerator needs. Key Features Complete assembly — includes both the motor and the fan blade Aftermarket replacement condenser fan motor — draws air across the condenser coils and compressor to remove system heat Resolves "whole fridge running warm," "23C or 23E error code," "noise or vibration from the compressor area," and "over-temperature alarm" symptoms caused by fan failure Rated 12V DC, 0.14A, 1.7W, approximately 1,120 RPM Direct drop-in replacement matching the original mounting and back panel cam-bracket attachment Replaces DA97-15765A, DA97-12842A, DA97-12842B, DA97-12842D, DA97-15765D, AP6001015, PS11733650, EAP11733650, DA31-00340A, RMF002ASSA, and 4959328 Aftermarket replacement built to OEM-equivalent quality standards DIY-friendly repair — typically completed in under an hour Product Specifications Part Number DA97-15765C OEM Part Number DA97-15765C Part Type Refrigerator Condenser Fan Motor Assembly (Motor + Blade) Condition Aftermarket Replacement Brand Samsung Location Compressor/machine compartment (back or bottom of cabinet) Function Cools the condenser coils and compressor Voltage 12V DC Amperage 0.14 A Wattage 1.7 W Speed ~1,120 RPM Related Error Codes 23C, 23E Quantity 1 fan motor assembly Compatible Brand Samsung Installation Notes ⚠️ Unplug Refrigerator Before Starting — Store Perishable Food Separately Disconnect power at the outlet before beginning, and move perishable food to a cooler for the duration of the repair. Wear work gloves. Remove all shelves from the upper refrigerator cabinet to improve access. Using a flat-blade screwdriver, gently ease the back panel away from the cabinet — on many models it's retained by a cam bracket and snaps into place, so it should release without excessive force. This exposes the condenser/circulating fan. Before condemning the motor, clear away any dust, lint, or debris built up around the condenser coils and fan blade — restricted airflow from a dirty coil produces symptoms similar to a failing motor and costs nothing to rule out. Photograph the wiring harness connector and the fan blade's position before disconnecting anything. Remove the two screws holding the fan in place, unplug the fan lead harness connector, and remove the defective fan assembly. Install the new DA97-15765C in the same position, reconnect the harness plug, and reinstall and tighten the two mounting screws securely. Confirm the blade spins freely by hand without contacting the housing or coils before reinstalling the back panel — it should snap back into place via the cam bracket. Reinstall the shelves, restore power, and monitor the refrigerator over the next 24 hours to confirm normal, even cooling has returned and any error code has cleared. Tools needed: flat-blade screwdriver, Phillips screwdriver, work gloves. Frequently Asked Questions My display shows a 23C or 23E error code. Does that mean I need this part? It's a strong indicator on many Samsung models, since these codes are commonly associated with condenser fan motor failure. Before ordering, it's still worth a quick visual check — clear any dust or debris from around the condenser coils and fan blade, since a heavily clogged condenser can sometimes trigger similar temperature-related codes. If the error persists after cleaning, or if the fan blade doesn't spin freely by hand, this assembly is the likely fix. The fan blade tries to spin but won't complete a full turn. Is that normal? No — this is a classic sign the motor bearings are wearing out or that something is obstructing the blade. A healthy condenser fan should spin freely and continuously once started. If you find yourself needing to give the blade a manual nudge to keep it turning, or it stalls partway through a rotation, the motor has failed and needs to be replaced rather than repeatedly restarted by hand. Both my fresh food and freezer sections are warm. Is this the right part? Yes, that pattern points toward the condenser fan rather than an evaporator fan. Because the condenser fan cools the compressor and coils that the entire refrigeration cycle depends on, a failing condenser fan tends to reduce cooling capacity across both compartments together, rather than leaving one side fine while the other struggles. Does this include the fan blade, or just the motor? This is a complete assembly that includes both the motor and the fan blade together, so there's no need to transfer a blade from your old unit or source one separately. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Samsung OEM part, but is manufactured to match the electrical specifications (12V DC, 0.14A, 1.7W, ~1,120 RPM), fan blade design, and mounting configuration of the original DA97-15765C condenser fan motor assembly used in compatible Samsung French door refrigerators. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

(5 Pack) EXPHV11 Microwave High Voltage Diode (Rectifier) Replaces:GE, LG, AMANA, ELECTROLUX, GE, KENMORE, MAYTAG, WHIRLPOOL, Frigidaire T3512, 3512, T4512, H, CL01-12, HVM12, 512 H, 12Kv, 350mA.    Replaces Part Numbers: 11QBP0236, AP5633254, PS4085133, AP3192533, PS239740 EA239740, WB27X10597, 13091701, AP6005641 PS11738693, WP13091701, 417726, 00188507 AP3382376 PS8712310, 00417726, PS11745270, AP6012063, 8205489, AP4357534, PS2339491, EA2339491, 5304467670, AP4564925, 3518400400, PS11745270, AP6012063, WP8205489, PS3654932, AP5631218, W10245187, W10492278. Description: This Diode Assembly is a replacement part for specific microwave models. It plays a crucial role in converting alternating current (AC) to direct current (DC), which is essential for the microwave’s high-voltage functions, including powering the magnetron to generate microwave energy. Over time, diodes can fail due to electrical surges, excessive heat, or wear and tear. A faulty diode assembly can lead to inefficient or non-functional microwave operation, impacting its ability to heat food properly. Microwave High Voltage Diode – Universal Replacement Restore your microwave’s heating function with this high-quality high voltage diode. Built to handle up to 12,000V / 500mA, it’s a reliable replacement for worn or damaged diodes in many major brands. Features: Direct replacement for most microwave models Durable and rated for high-voltage performance Fixes common issues like no heat or humming Fits brands: GE, Whirlpool, LG, Samsung, Panasonic, Frigidaire, and more. ⚠️ Installation should be done with power disconnected. Not sure if it fits? Contact us to confirm compatibility.

Read more less

ERP WR60X203 Refrigerator Evaporator Fan Motor 120V, 60Hz, .21A, 3000RPM. 1-1/2" shaft. Has 2 (1/4") and 1 (3/16") terminals.   Replaces Part Numbers: WR60X203, 305540, AH304745, AP2071899, EA304745, PS304745, WR60X0191, WR60X0203, WR60X191   This is an aftermarket part that can be used as a replacement for the OEM part. California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less