AAN73209838 Genuine OEM LG Washer Drain Pump & Cabinet Base Assembly
The AAN73209838 is a genuine LG OEM combined drain pump and cabinet base assembly for LG washers. This assembly bundles the washer's drain pump — which pumps water out of the drum and through the drain hose at the end of each cycle — together with the cabinet base structure it's mounted to. Because these two components ship together as one assembly, replacing this part addresses both the drain pump function and the base structure it sits in at the same time.
Common causes of failure include a worn or jammed drain pump motor, or physical damage or corrosion to the cabinet base itself over years of use. A failing assembly typically shows up as the washer failing to drain, unusual noise during the drain phase, or water leaking from underneath the unit.
Quick Answer
The AAN73209838 Genuine OEM LG Washer Drain Pump & Cabinet Base Assembly fixes LG washers that won't drain, make unusual noise during the drain phase, or are leaking water from underneath the unit. Combined drain pump and cabinet base assembly. This is a larger, heavier assembly than a standalone drain pump — installation involves more disassembly than a simple pump swap.
Common Problems This Part Fixes
Washer not draining — standing water left in the tub after a cycle
Unusual noise during the drain phase of the cycle
Water leaking from underneath the washer
Cycle stalling or failing to advance past the drain step
Visible damage or corrosion to the cabinet base structure
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
AAN73209838, 4873470, 4985882, AHA75673401, AP6991753, AP6991765, EAP12580277, EAP16222263, FIX16222263, PS12580277, PS16222263, ALG51685, PD00091778
We were not able to confirm additional cross-reference or superseding part numbers for this specific part from reliable sources at the time this page was built, so none are listed here rather than guessed. If you have a cross-reference number for your appliance, contact our support team and we will verify compatibility before you order.
Compatibility
This drain pump and cabinet base assembly is compatible with select LG top-load washers, including model numbers such as WT7060CW, WT7100CW, WT7250CW, WT7300CV, T1780WFHT, and T1789EFH5T/T1789EFH5U/T1789EFHT/T1789EFHKD variants.
Note: This is a combined assembly, not a standalone drain pump — if your washer only needs the pump replaced and the cabinet base is intact, ask our support team whether a standalone pump option is available for your model before ordering this larger assembly. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure.
Key Features
Genuine LG OEM part — factory-specified pump and base assembly
Combined drain pump and cabinet base assembly in a single part
Resolves "won't drain," "noisy drain phase," and "leaking underneath the washer" symptoms
Direct drop-in replacement — matches the original mounting and hose connections
Compatible with a range of LG top-load washer models
Genuine OEM replacement — guaranteed fit, materials, and performance
Product Specifications
Part Number
AAN73209838
Part Type
Washer Drain Pump & Cabinet Base Assembly
Condition
Genuine OEM
Brand
LG
Application
Top-Load Washers
Function
Pumps water from the drum through the drain hose; provides the cabinet base structure
Repair Difficulty
Moderate to Hard — larger assembly than a standalone pump
Quantity
1 combined assembly
Compatible Brand
LG
Installation Notes
⚠️ Unplug Washer And Shut Off Water Supply Before Starting — Remove Standing Water First Disconnect power at the outlet or shut off the circuit breaker, and shut off the water supply before beginning. Wear work gloves. If there's standing water left in the tub from the original failure, remove as much as possible by hand with a cup or towel before starting the repair. Because this is a combined pump and cabinet base assembly rather than a standalone pump, access typically requires tipping the washer back or removing more of the cabinet than a simple pump swap — check your model's service diagram for the exact disassembly sequence, since it varies by model. Photograph the wiring and hose connections before disconnecting anything. Disconnect the electrical connector and the drain hose connections from the old assembly, remove the fasteners securing it to the washer frame, and carefully remove it, noting how the base supports the rest of the cabinet. Install the new AAN73209838 assembly in the same position, reconnect the drain hose connections securely, reconnect the electrical connector fully, and secure all mounting fasteners. Reassemble the cabinet in reverse order, restore the water supply and power, then run a cycle and check underneath for leaks while confirming the tub drains completely at the end. Tools needed: Phillips screwdriver, socket set, pliers, towels or a small cup for removing standing water, work gloves.
Frequently Asked Questions
Do I need this whole assembly, or is there a smaller drain pump option for my model?
Some LG washer models offer a standalone drain pump as a separate, smaller part, while others require this combined pump-and-base assembly because the two are integrated on that particular platform. Check with our support team using your model number to confirm whether a standalone pump is available for your washer before ordering this larger assembly, since it can save you time and cost if a smaller part fits your model.
Why is this repair more involved than a typical drain pump replacement?
Because this part includes the cabinet base structure along with the pump, accessing and replacing it typically involves more disassembly than swapping a standalone pump alone — you're not just disconnecting a pump, you're also working with part of the washer's supporting frame. Budget more time for this repair than you would for a simple pump-only replacement, and consider having a second person help support the cabinet during removal and installation.
Is this an OEM or aftermarket part?
This is a genuine OEM part, manufactured by LG to factory specifications — guaranteed fit, materials, and performance. It matches the original pump design, hose connections, and cabinet base mounting configuration of the assembly originally installed in your washer.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
WD19X25278 Dishwasher Diverter Assembly
The XPARTCO WD19X25278 is an aftermarket replacement diverter assembly for GE dishwashers, and also fits select Hotpoint, Haier, Monogram, and Café models. This assembly controls the flow of water to the spray arms, directing wash water to the upper or lower spray arm at the correct point in the cycle for thorough, even cleaning.
The assembly includes a valve and float mechanism designed to optimize water flow while minimizing noise. Common causes of failure include a worn or cracked diverter valve, or a rubber boot/hose connection that develops a leak over time. Symptoms of a failing diverter assembly include water pooling underneath the dishwasher, poor washing performance from one or both spray arms, or unusual noise during the wash cycle. It directly replaces AP6871922, WD18X21678, 4922277, PS12710077, WD00X25260, WD19X25259, and WD19X25278-25PK.
Quick Answer
The XPARTCO WD19X25278 Dishwasher Diverter Assembly fixes GE, Hotpoint, Haier, Monogram, and Café dishwashers with water pooling underneath the unit, poor washing performance from the spray arms, or unusual noise during the cycle. Replaces AP6871922, WD18X21678, 4922277, PS12710077, WD00X25260, WD19X25259, WD19X25278-25PK. Make sure the diverter is fully engaged with the spout on the wash pump before tightening the hose clamp — one customer had the tube cut when tightening the clamp without full engagement first.
Common Problems This Part Fixes
Water pooling or leaking underneath the dishwasher
Poor washing performance from one or both spray arms
Unusual noise during the wash cycle
Water not properly directed to the correct spray arm
Inconsistent cleaning results between the upper and lower racks
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This dishwasher diverter assembly directly replaces the following OEM and cross-reference part numbers:
WD19X25278, 4466639, 4922277, WD00X25260, WD18X21678, WD19X25259, WD19X25278-25PK, AP6024268, AP6871922, AGE24645, PD00049646, EAP11736568, EAP12710077, PS11736568, PS12710077
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This diverter assembly is compatible with select GE dishwashers, and also fits select Hotpoint, Haier, Monogram, and Café dishwashers built on the GE platform, including model numbers such as ADT521PGJ0BS, ADT521PGJ0WS, ADT521PGJ2BS, GDT655SGJ5BB, GDF510PGJ0BB, GDF511PGM0WW, GDF520PGJ0BB, and GDF530PGM0BB.
Note: The assembly may include multiple parts depending on your model — refer to your appliance's parts diagram for a complete list. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure.
Key Features
Aftermarket replacement diverter assembly — controls water flow to the spray arms
Resolves "water pooling underneath," "poor spray arm performance," and "unusual noise" symptoms
Valve and float assembly engineered to optimize water flow while minimizing noise
Direct drop-in replacement matching the original mounting and connections
Replaces AP6871922, WD18X21678, 4922277, PS12710077, WD00X25260, WD19X25259, and WD19X25278-25PK
Compatible with GE, Hotpoint, Haier, Monogram, and Café dishwashers
Aftermarket replacement built to OEM-equivalent quality standards
DIY-friendly repair
Product Specifications
Part Number
WD19X25278
OEM Part Number
WD19X25278
Part Type
Dishwasher Diverter Valve Assembly
Condition
Aftermarket Replacement
Function
Controls water flow direction to the upper and lower spray arms
Design
Valve and float assembly
Repair Difficulty
Easy to Moderate — DIY-friendly
Quantity
1 diverter assembly
Compatible Brands
GE, Hotpoint, Haier, Monogram, Café
Installation Notes
⚠️ Unplug Dishwasher And Shut Off Water Supply Before Starting — Fully Engage The Spout Before Tightening The Clamp Disconnect power at the outlet or shut off the circuit breaker, and shut off the water supply before beginning. Wear work gloves. Open the dishwasher door and remove the racks to expose the bottom of the dishwasher. Locate the diverter assembly at the bottom of the unit and remove the two screws securing it in place. Disconnect the old assembly from the wash pump spout and any hose connections. Before tightening the hose clamp on the new assembly, make sure the diverter is fully and securely engaged with the spout on the wash pump. One customer had their diverter's tube cut when the clamp was tightened without the assembly being fully seated first — take your time to confirm a proper seat before applying clamp pressure. Secure the new WD19X25278 assembly in place with the two mounting screws. Reconnect any hose connections and reinstall the dish racks. Restore the water supply and power, then run a test cycle — ideally checking underneath the unit partway through — to confirm no leaking from the diverter area and correct water distribution to both spray arms. Tools needed: Phillips screwdriver, pliers, work gloves.
Frequently Asked Questions
I'm seeing water pooling under my dishwasher. Is this the part I need?
Yes, this is a commonly documented symptom. If the diverter's rubber boot or hose connection has developed a leak, water can spray or drip during the wash cycle and collect underneath the unit. One customer traced their leak to a factory-defective hose in the diverter assembly, and unfortunately the leaking water had also gotten into their circulation pump motor over several loads, eroding the motor brushes — so it's worth inspecting the pump motor as well if you've had a diverter leak for a while before noticing it.
Any tips to avoid damaging the new part during installation?
Yes — make sure the new diverter is fully engaged with the spout on the wash pump before tightening the hose clamp. One customer's first replacement part was ruined because the clamp was tightened before the assembly was properly seated, which cut into the tube. Taking an extra moment to confirm a full, secure connection before clamping down prevents this.
Is this a difficult repair?
No, this is generally a DIY-friendly repair. It involves removing the dish racks, unscrewing two mounting screws to access the diverter at the bottom of the dishwasher, and swapping the assembly, typically without needing to pull the dishwasher out from under the counter.
Is this an OEM or aftermarket part?
This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine GE OEM part, but is manufactured to match the valve and float design, mounting configuration, and connections of the original WD19X25278 diverter assembly used in compatible GE, Hotpoint, Haier, Monogram, and Café dishwashers.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
XPARTCO WE03X37317 - WE03X37318 Dryer Drum Glide Set
The XPARTCO WE03X37317 - WE03X37318 is an aftermarket replacement drum glide set for GE and Hotpoint dryers, also used on select Whirlpool and Kenmore dryers and washer-dryer combos. These plastic bearing slides are the wear pads at the front of the dryer that the drum rides on as it turns. As they wear down, the drum no longer sits and rolls smoothly, and the dryer starts to squeak, squeal, or rumble. In worse cases the drum catches or drags, and clothes can get snagged or marked between the drum and the front frame.
This set pairs both glide types used on these dryers: the WE03X37317 and the WE03X37318 front bearing slides. Because the slides wear at the same rate, replacing them together restores smooth, quiet drum rotation and avoids a repeat repair. Easy to install, typically 30–60 minutes.
Quick Answer
The XPARTCO WE03X37317 - WE03X37318 Drum Glide Set fixes a GE or Hotpoint dryer that squeaks, squeals, or rumbles loudly as the drum turns, or whose drum drags or catches. Replaces both the WE03X37317 and WE03X37318 front bearing slides. Classic symptom: a loud squeal or scraping noise from the drum area that gets worse over the cycle, sometimes with marks or snags on clothes.
Common Problems This Part Fixes
Loud squeaking, squealing, or scraping noise while the drum tumbles
Drum not spinning smoothly, or dragging and catching
Marks, wrinkles, or snags on clothes from items catching between the drum and the front frame
Excessive drum noise during drying cycles
Visibly worn, thin, or chewed-up plastic glides at the front of the drum
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This glide set replaces the following part numbers:
WE03X37317, WE1M1067, WE01M0316, WE03X37317-50PK, WE1M1067-100PK, WE1M316, WE1M481, WE1M507, AGE25692, AP5668531, AP7217723, FIX17137203, PD00089026, PS6447706, PS17137203, WE03X37318, WE1M504, WE01M0333, WE1M333, TJDE504, TJWE1M333, DE504, DE775, TJDE775, AH755842, EA755842, ERWE1M333, AGE25703, AP7217724, PD00088960, PS17137205
The first group of numbers (WE03X37317, WE1M1067, WE1M316, WE1M481, WE1M507, AP7217723, PS17137203) is for the gray glide. The second group (WE03X37318, WE1M504, WE01M0504, WE01M0333, WE1M333, AP7217724, PS17137205) is for the white glide. The AP/PS-prefixed numbers are third-party catalog cross-references for the same physical parts.
Compatibility
These glides are used on GE, Hotpoint, Whirlpool, and Kenmore dryers and washer-dryer combos, including models such as:
GE 61140418, 61140419, 61148418, 61148419
Numerous additional GE and Hotpoint dryer and washer-dryer combo models
Note: These glides fit a wide range of models, so the list above is only a sample. Compare the glides in your dryer, or your parts diagram, against the Replaces list above, or contact our support team with your model number and we'll verify fit before you order.
Key Features
Aftermarket replacement drum glide set covering both the WE03X37317 and WE03X37318 front bearing slides
Durable plastic bearing slides that let the drum rotate smoothly
Resolves squeaking, squealing, and dragging drum symptoms
Helps prevent clothes from being marked or snagged at the front of the drum
Replacing both glide types together avoids a repeat repair
Easy installation — typically 30–60 minutes
Product Specifications
Part Number
XPWE03X37317-WE03X37318
OEM Part Number
WE03X37317, WE03X37318
Part Type
Dryer Drum Glide (Front Bearing Slide) Set
Condition
Aftermarket Replacement
Set Includes
WE03X37317 and WE03X37318 Front Bearing Slides
Material
Plastic
Application
GE, Hotpoint, Whirlpool & Kenmore Dryers and Washer-Dryer Combos
Installation Notes
⚠️ Unplug Power Before Installing Unplug the dryer or switch off its circuit breaker, and shut off the gas supply first if it's a gas model. Remove the top and front panels per your model's service guide to expose the front of the drum, and disconnect any wiring that's in the way. Lift or support the drum enough to reach the worn glides, which are held in place at the front bearing support. Pull out the old glides, noting the position and orientation of each, and fit the new ones in the same positions. Reassemble the dryer and spin the drum by hand to confirm it turns smoothly before restoring power. Replace the glides as a set, since they wear at the same rate.
Frequently Asked Questions
My dryer squeals or rumbles loudly while tumbling — is this the part I need?
Worn drum glides are a very common cause of squeaking and scraping from the drum area. If the plastic glides look thin, grooved, or chewed up, replacing them should quiet the dryer and restore smooth rotation. Also check the drum rollers and idler pulley, which can cause similar noises.
Why are there two different part numbers?
GE uses two glide types at the front of the drum: glide (WE03X37317) and glide (WE03X37318). This set covers both, so you can replace the full set in one go.
Should I replace all the glides or just the worn ones?
Replace them together. The glides wear at about the same rate, so if one is worn the others are usually close behind.
Will this fit my Whirlpool or Kenmore dryer?
These glides are cross-listed for select Whirlpool and Kenmore dryers and washer-dryer combos as well as GE and Hotpoint. Compare the part numbers on your parts diagram against the Replaces list, or contact our support team with your model number and we'll confirm.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout
XPARTCO W11688994 Washer Water Inlet Valve (Hot)
The XPARTCO W11688994 is an aftermarket replacement hot water inlet valve compatible with select Whirlpool, Maytag, Amana, KitchenAid, Jenn-Air, Magic Chef, Admiral, Norge, Roper, Inglis, and Kenmore front-load washers. The hot water inlet valve is mounted at the back of the washer where the hot water supply hose connects. When the washer's control board calls for hot water during a wash cycle, the valve's internal solenoid opens, letting hot water flow into the tub or detergent dispenser. The valve closes the instant the control board cuts power, stopping flow precisely as the correct fill level is reached.
When this valve fails, the washer may not fill with hot water at all, fill very slowly with hot water, fail to deliver hot or warm wash temperatures (even when selected), continuously drip water into the tub even when off, or display fill-related error codes. Construction is red and white plastic with a metal solenoid coil, ~3"H x 4"W x 3"L, with 1/2" NPT threaded inlet for standard washer supply hose. It directly replaces W11688994, W11036928, W11316255, W11486360, and AP7218602. Often replaced as a pair with the cold water inlet valve (W11688995, sold separately). Installs in 10–15 minutes with basic hand tools.
Quick Answer
The XPARTCO W11688994 Washer Water Inlet Valve (Hot) fixes Whirlpool, Maytag, Amana, KitchenAid, Jenn-Air, and Kenmore front-load washers that aren't filling with hot water, fill slowly with hot water, can't reach hot or warm wash temperatures, or have continuous water dripping into the tub when off. Red/white plastic with metal coil, 1/2" NPT thread, ~3"H x 4"W x 3"L. Replaces W11036928, W11316255, W11486360, AP7218602. Often paired with the cold water valve (W11688995, sold separately).
Common Problems This Part Fixes
Washer not filling with hot water — valve solenoid not opening when commanded
Washer filling slowly with hot water — valve partially clogged or weak solenoid
No hot or warm water in selected wash temperatures — only cold water flowing in
Hot wash cycle running cool — hot valve not delivering normal flow
Water continuously dripping into the tub when the washer is off — hot valve stuck open or not fully closing
Water leaks at the hot valve body — internal seal failure
Wash cycles taking much longer than normal due to slow hot fill
Fill-related error codes when hot fill is required by the selected cycle
Replaces Part Numbers
This hot water inlet valve directly replaces the following OEM and cross-reference part numbers:
W11688994, W11316255, W11036928, W11486360, 4983330, AP7218602, AWP46795, EAP17216729, FIX17216729, OEM21655815, PD00085626, PS17216729.
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This hot water inlet valve is compatible with select front-load washers from the following brands:
Whirlpool front-load washers — 7MWFC9822HC1, 8TWFC6810LW0, WFC682CLW0, WFC6810LW0, WFC9820HC0, WFC9820HW0 series
Whirlpool front-load washers — WFW560CHW0, WFW560CHW1, WFW560CHW2, WFW560CHW3, WFW560CHW4 series
Whirlpool front-load washers — WFW5605MC0, WFW5605MW0 series
Whirlpool front-load washers — WFW5620HW0, WFW5620HW1, WFW5620HW2, WFW5620HW3 series
Whirlpool front-load washers — WFW6620HC0, WFW6620HC1, WFW6620HC2, WFW6620HW0, WFW6620HW1 series
Whirlpool front-load washers — WFW8620HC0, WFW8620HC1, WFW8620HC2, WFW8620HC3, WFW8620HC4, WFW8620HW0, WFW8620HW1, WFW8620HW2, WFW8620HW3, WFW8620HW4 series
Whirlpool front-load washers — WFW862CHC0, WFW862CHC1, WFW862CHC2, WFW862CHC3 series
Whirlpool front-load washers — WFW9620HBK1, WFW9620HBK2, WFW9620HBK3, WFW9620HC0, WFW9620HC1, WFW9620HC3, WFW9620HW0, WFW9620HW1, WFW9620HW2, WFW9620HW3 series
Maytag front-load washers — MHW5630HC0-HC3, MHW5630HW0-HW3, MHW6630HC0-HC3, MHW6630HW0-HW3, MHW8630HC0-HC4, MHW8630HW0-HW4 series
Amana front-load washers — NFW5800HW0, NFW5800HW1, NFW5800HW2, NFW5800HW3, NFW5800HW4 and related models
Inglis front-load washers — IFW5900HW0, IFW5900HW1, IFW5900HW2, IFW5900HW3, IFW5900HW4 and related models
KitchenAid, Jenn-Air, Magic Chef, Admiral, Norge, Roper front-load washers — select Whirlpool-built models
Kenmore / Sears front-load washers — select Whirlpool-built models
Note: This is the hot water inlet valve (typically red). The matching cold water inlet valve is part number W11688995 (typically blue). When you replace one valve, it's a good practice to replace the other at the same time since they're the same age, both are accessible during the same repair, and the second valve will likely fail in the near term. Always verify your model number before ordering.
Key Features
Aftermarket replacement built to OEM-equivalent quality standards
Controls the flow of hot water into the washer during fill cycles
Solenoid-actuated — opens precisely when the control board calls for hot water and closes the moment the call is dropped
1/2" NPT threaded inlet for standard washer supply hose connection
Dimensions: approximately 3" H x 4" W x 3" L
Red and white plastic body with metal solenoid coil — heat-resistant construction designed for hot water cycle pressure and temperature
Replaces W11036928, W11316255, W11486360, AP7218602, and PD00085626
Compatible with Whirlpool, Maytag, Amana, KitchenAid, Jenn-Air, Magic Chef, Admiral, Norge, Roper, Inglis, and Kenmore front-load washers
Often replaced together with the cold water inlet valve (W11688995, sold separately) as a paired repair
Quick DIY repair — installs in 10–15 minutes with basic hand tools
Product Specifications
Part Number
XPW11688994
Part Type
Washer Water Inlet Valve (Hot)
Condition
Aftermarket Replacement
Application
Front-Load Washers (Whirlpool platform)
Water Type
Hot (paired cold valve is W11688995)
Inlet Thread
1/2" NPT
Dimensions
Approximately 3" H x 4" W x 3" L
Color
Red / White
Material
Plastic / Metal (heat-resistant)
Often Paired With
Cold Water Inlet Valve (W11688995, sold separately)
Compatible Brands
Whirlpool, Maytag, Amana, KitchenAid, Jenn-Air, Magic Chef, Admiral, Norge, Roper, Inglis, Kenmore
Installation Notes
⚠️ Unplug Washer and Shut Off Water Supply Before Starting — Wear Work Gloves Disconnect power and shut off both the hot and cold water supplies at the wall before beginning. Wear work gloves to protect your hands. Have towels ready — residual water remains in the supply hoses and will spill when disconnected. Important: if the washer has just been running a hot cycle, allow the hot supply hose and valve to cool before handling — hot water can scald. Pull the washer out from the wall to access the back. Remove the three 1/4" screws securing the rear edge of the top cover, push the top cover slightly back, and lift it off. Locate the inlet valves at the back of the washer — the hot valve is typically red. Disconnect the hot water supply hose from the valve (water will drip — towels). Photograph the wire connections before disconnecting. Unplug the small electrical connector from the valve solenoid. Remove the single 3/16" mounting screw (or similar hardware, model-dependent) holding the valve in place, and disconnect any internal water hoses from the valve outlet (channel-lock pliers may help with hose clamps). Install the new W11688994 valve in the same position with the same orientation, reconnect the internal water hoses and electrical connector, and secure the mounting screw. Reconnect the hot supply hose at the wall, restore water and power, and run a test cycle on a hot or warm setting to confirm normal hot water fill with no leaks. Tip: while the top cover is off, this is the ideal time to also replace the cold water valve (W11688995) — they share the same access and lifespan. Tools needed: 1/4" nut driver, 3/16" nut driver, adjustable wrench or pliers, work gloves.
Frequently Asked Questions
My washer isn't filling with hot water — is the hot valve the problem?
Likely, yes — that's the most common symptom of a failed hot water inlet valve. Before replacing, do a few quick checks: 1) confirm the hot water supply at the wall is turned on and your home actually has hot water at that connection (test the faucet nearby); 2) check the supply hose for kinks or pinches; 3) inspect the inlet screen on the back of the valve for sediment buildup — a clogged screen can mimic a failed valve. If the supply is good and the screen is clean, but the washer still won't get hot water, the W11688994 valve solenoid has likely failed and replacing it will resolve the issue.
My washer fills but my hot wash isn't actually hot — could it still be this valve?
Yes — when the hot inlet valve is partially failed (opening but not fully, or opening only briefly), the washer may complete its fill cycle by drawing extra cold water to compensate, but the resulting mix is much cooler than the selected wash temperature should be. If you've confirmed your home's hot water is hot, the supply hose is good, and you're still ending up with lukewarm "hot" washes, the hot valve is a likely cause. Replacing it restores proper hot water delivery and accurate wash temperatures.
Should I replace the cold water valve at the same time?
Yes, it's strongly recommended. The hot and cold inlet valves are essentially identical components installed side by side at the back of the washer — they're the same age, are exposed to the same wash cycle stress, and have the same expected service life. When one fails, the other is typically not far behind. Since the top cover is already off and both valves are accessible during the same repair, replacing both saves you a second teardown later. The matching cold water valve is part number W11688995 (blue, sold separately) and is also available as a paired kit.
My washer is dripping water into the tub even when it's off — could the hot valve be the cause?
Yes, that's a classic sign of a failed inlet valve. When the solenoid wears out or debris keeps the valve from sealing fully closed, water leaks past it at low rates and drips into the tub even with the washer powered off — especially noticeable as a slow puddle forming over a day or two. Since both the hot and cold valves feed into the tub, you'll want to identify which one is leaking: shut off the cold water supply at the wall and check if dripping continues. If it stops, the cold valve is at fault; if it continues, this hot valve is the cause. Replacing the W11688994 will resolve a leaking hot valve.
Is this an OEM or aftermarket part?
This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured to match the dimensions, electrical specifications, 1/2" NPT thread, and solenoid function of the original W11688994 hot water inlet valve used in compatible Whirlpool, Maytag, Amana, KitchenAid, and Kenmore front-load washers.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout
AHA75673401 Washer Genuine Drain Pump
Fits Specific LG Washer models
Description: This Washing Machine Drain Pump is an OEM part for specific LG washing machine models. It is responsible for effectively draining water out of the washing machine after each cycle. The pump works to remove water from the tub and drain hoses, preparing the machine for the next load.
Replaces Part Numbers: AHA75673401, 4873470, AP6335290, PS12580277.
California Residents only
WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov
XPARTCO 8182703 Washer Shock Absorber Replaces WP8182703
The XPARTCO 8182703 is an aftermarket replacement front-load washer shock absorber compatible with select Whirlpool, Maytag, Kenmore, KitchenAid, Amana, Jenn-Air, Admiral, and Roper front-load washers in the GHW, WFW, MHWE, MFW, and KHWS series. The shock absorber is a hydraulic dampener that connects the outer washer tub to the base frame. During the spin cycle, the shock absorbers absorb and dampen the vibrations and movement generated by the spinning drum — keeping the washer stable, quiet, and protecting internal components from damage caused by excessive movement.
Most compatible Whirlpool-family front-load washers use four shock absorbers — two at the front and two at the rear. When one or more shock absorbers wear out, the outer tub vibrates excessively, causing loud banging or thumping during the spin cycle. It is strongly recommended to replace all four shock absorbers at the same time. This listing is for a single shock absorber. It directly replaces WP8182703, 8181646, 1173231, and several additional cross-reference numbers. Installs in 30–45 minutes with basic hand tools.
Quick Answer
The XPARTCO 8182703 Washer Shock Absorber fixes front-load washers that shake violently, bang loudly, or walk across the floor during the spin cycle. The shock absorber dampens tub vibration. Most models use 4 shock absorbers — replace all 4 at the same time. Sold individually. Compatible with Whirlpool, Maytag, Kenmore, KitchenAid, Amana, Jenn-Air, Admiral, and Roper front-load washers. Replaces WP8182703, 8181646, AP6011831, and more.
Common Problems This Part Fixes
Violent shaking or vibrating during the spin cycle
Loud banging, thumping, or clunking noise during spin
Washer "walking" across the floor during the spin cycle
Outer tub hitting the sides of the cabinet during high-speed spin
Spin cycle errors caused by excessive tub movement triggering the imbalance sensor
Visible oil leak, broken mount, or collapsed shock absorber body
Washer repeatedly pausing spin cycle and redistributing the load without resolving the vibration
Replaces Part Numbers
This shock absorber directly replaces the following OEM and cross-reference part numbers:
WP8182703, 8182703, 1173231, 8181646, EAP11745030, AWP48892, PD00003153, AP6011831, PS11745030.
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This shock absorber is compatible with select front-load washers from the following brands and series:
Whirlpool front-load washers — GHW and WFW series
Maytag front-load washers — MHWE and MFW series
Kenmore / Sears front-load washers (select Whirlpool-built models)
KitchenAid front-load washers — KHWS series
Amana front-load washers
Jenn-Air front-load washers
Admiral front-load washers
Roper front-load washers
Important: Most compatible models use 4 shock absorbers (2 front, 2 rear). This part is sold individually. It is strongly recommended to replace all 4 at the same time, as the remaining absorbers have experienced the same wear and will fail soon after.
Key Features
Hydraulic dampener that connects the outer washer tub to the base frame — absorbs spin cycle vibration and prevents tub-to-cabinet contact
Keeps the washer stable and quiet during high-speed spin cycles, protecting drum bearings, seals, and cabinet from premature wear
High-quality reinforced construction — excellent toughness, oil resistance, and resistance to weak acids and alkalis for long service life
Direct replacement for WP8182703 and 8181646 — no modification required
Compatible with Whirlpool GHW, WFW, Maytag MHWE, MFW, and KitchenAid KHWS series front-load washers
Sold individually — most models require 4 shock absorbers; replace all 4 at the same time
Aftermarket replacement built to OEM-equivalent quality standards
DIY repair — installs in 30–45 minutes with basic hand tools
Product Specifications
Part Number
8182703
OEM Part Number
WP8182703
Part Type
Front-Load Washer Shock Absorber (Hydraulic Dampener)
Condition
Aftermarket Replacement
Application
Front-Load Washers
Quantity Per Washer
4 (2 front, 2 rear) — sold individually
Compatible Brands
Whirlpool, Maytag, Kenmore, KitchenAid, Amana, Jenn-Air, Admiral, Roper
Compatible Series
GHW, WFW, MHWE, MFW, KHWS
Installation Notes
⚠️ Unplug Washer and Shut Off Water Before Starting Unplug the washer and turn off the water supply before beginning. To access the front shock absorbers, remove the lower front access panel. To access the rear shock absorbers, pull the washer away from the wall, disconnect the water hoses, and remove the rear panel. The shock absorbers connect the outer tub to the base frame with mounting pins at the top and bottom — turn the shock absorber 90 degrees at both pins to release and remove it. Install the new 8182703 shock absorber by inserting the pins into the top and bottom mounting brackets and rotating 90 degrees to lock in place. Replace all 4 shock absorbers during the same repair. Reconnect all panels and water hoses, plug in the washer, restore water supply, and run a spin cycle to verify normal operation. Work gloves are recommended as there are sharp edges inside the cabinet. Tools needed: Phillips screwdriver, channel-lock pliers, work gloves.
Frequently Asked Questions
What does the washer shock absorber do?
The shock absorbers are hydraulic dampeners that connect the outer washer tub to the base frame of the machine. During the spin cycle — when the drum spins at high speeds — the shock absorbers absorb and dampen the vibrations and movement of the heavy outer tub, keeping it centered and preventing it from striking the sides of the washer cabinet. Without functioning shock absorbers, the washer vibrates violently, makes loud banging noises, and can "walk" across the floor during spin, potentially damaging internal components over time.
How many shock absorbers does my front-load washer have?
Most Whirlpool-family front-load washers compatible with the 8182703 shock absorber use four shock absorbers — two mounted at the front of the tub and two at the rear. This listing is for a single shock absorber. When replacing shock absorbers, it is strongly recommended to replace all four at once, as they all experience the same amount of use and the remaining absorbers are likely to fail soon after the first one.
What is the difference between 8182703 and WP8182703?
These are the same shock absorber. WP8182703 is the updated Whirlpool OEM part number that superseded the original 8182703. The 8181646 is also a cross-reference to this same part. This aftermarket replacement is compatible with all three numbers.
My washer still vibrates after replacing the shock absorbers — what else could it be?
If vibration persists after replacing all four shock absorbers, other possible causes include an unbalanced or overloaded drum, worn drum bearings, a failing suspension spring, or the washer not being level on the floor. Check that the washer's leveling feet are adjusted so all four corners are in firm contact with the floor. Also confirm the load is not oversized — overloading is the most common cause of spin vibration and can prematurely wear shock absorbers.
Is this an OEM or aftermarket part?
This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured from high-quality reinforced materials to match the dimensions and performance of the original WP8182703 shock absorber.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout
XPARTCO WH05X24185 Washer Clutch
The XPARTCO WH05X24185 is an aftermarket replacement clutch for GE top-load washers, and also fits select Hotpoint, Haier, Monogram, and Café models. This clutch engages and disengages the transmission during the wash and spin cycles, transferring the motor's power to spin the basket so your clothes finish damp rather than soaked.
Made of white plastic with a glossy finish, measuring approximately 3"L x 3"W x 1"H. Sold individually and does not include any other parts, such as the shift actuator (our WH03X30517 listing) that works alongside it. Common causes of failure include wear and tear over time, excessive load, or mechanical obstruction. Symptoms of a worn or failing clutch include clothes coming out wet even after a completed spin cycle, a slight burning odor during operation, or issues with spinning or agitating. It directly replaces WH05X24185, 4588013, AGE26046, AP5993402, EAP11729473, PD00043605, PS11729473.
Quick Answer
The XPARTCO WH05X24185 Washer Clutch fixes GE, Hotpoint, Haier, Monogram, and Café top-load washers where clothes come out wet after spinning, there's a slight burning odor during operation, or the washer has trouble spinning or agitating. White plastic, glossy finish, ~3"L x 3"W x 1"H. Sold individually. Replaces WH05X24185, 4588013, AGE26046, AP5993402, EAP11729473, PD00043605, PS11729473. If you also see grease pooling on the floor under the washer, that's more likely a transmission gearcase leak than this clutch — and if the agitator only slips in one direction, check the agitator bolt before assuming the clutch has failed.
Common Problems This Part Fixes
Clothes coming out wet even after a completed spin cycle
Slight burning odor during operation
Washer having trouble spinning or agitating
Reduced washer performance from clutch wear
Grinding or unusual noise tied to the transmission area
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This washer clutch directly replaces the following OEM and cross-reference part numbers:
WH05X24185, 4588013, AGE26046, AP5993402, EAP11729473, PD00043605, PS11729473
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This clutch is compatible with select GE top-load washers, and also fits select Hotpoint, Haier, Monogram, and Café washers built on the GE platform.
Note: This clutch is commonly replaced alongside our WH03X30517 shift actuator, since the two work together in the same wash/spin transition system, but they are sold separately. If your washer also isn't switching between agitation and spin, check the actuator as well. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure.
Key Features
Aftermarket replacement clutch — engages and disengages the transmission during wash and spin
Resolves "clothes still wet," "burning odor," and "trouble spinning or agitating" symptoms
White plastic, glossy finish
Approximately 3"L x 3"W x 1"H
Direct drop-in replacement matching the original mounting
Replaces WH05X24185, 4588013, AGE26046, AP5993402, EAP11729473, PD00043605, PS11729473
Compatible with GE, Hotpoint, Haier, Monogram, and Café top-load washers
Aftermarket replacement built to OEM-equivalent quality standards
Sold individually
Product Specifications
Part Number
XPWH05X24185
OEM Part Number
WH05X24185
Part Type
Washer Clutch
Condition
Aftermarket Replacement
Color
White
Material
Plastic
Finish
Glossy
Dimensions
Approx. 3"L x 3"W x 1"H
Related Part
WH03X30517 shift actuator (sold separately)
Repair Difficulty
Moderate — some disassembly required
Quantity
1 clutch (sold individually)
Compatible Brands
GE, Hotpoint, Haier, Monogram, Café
Installation Notes
⚠️ Unplug Washer Before Starting Disconnect power at the outlet before beginning to cut off electricity and prevent accidental shocks. Wear work gloves. Remove the two screws at the back of the washer with a Phillips head screwdriver, then pull off the main console and carefully set it aside. Locate the access plate on the transmission side and remove the screws securing it. Take the belt off the pulley and remove the belt guard. Remove the four screws that secure the clutch and take it off from the wet end of the transmission. Install the new WH05X24185 clutch and replace the four screws. Reattach the belt, pulley, and access plate, and replace their screws. Put the main console back onto the washer and secure it with the two screws. Restore power and run a test cycle to confirm clothes are coming out properly damp at the end of the spin cycle, with no burning odor or unusual noise. Tools needed: Phillips screwdriver, socket wrench, work gloves.
Frequently Asked Questions
My clothes come out wet after the spin cycle. Is this the clutch I need?
Yes, this is one of the most common symptoms of a worn or failing clutch. Since this clutch is what engages the transmission to spin the basket at high speed, a worn clutch can slip rather than fully engaging, leaving clothes wetter than they should be at the end of the cycle. A slight burning odor during operation is another documented sign of the same wear.
I noticed grease on the floor under my washer. Is that this clutch leaking?
Not directly — grease pooling under the washer typically comes from the gearcase transmission itself rather than the clutch. If you're seeing this symptom, the transmission may need attention in addition to, or instead of, this clutch, depending on what else you're experiencing.
My agitator slips going one direction but not the other. Is that the clutch?
Not necessarily. This specific symptom — the agitator pulling fine in one direction but slipping in the other — is more often traced to a loose agitator bolt. It's worth checking and tightening that bolt first; if the problem persists, the agitator base hybrid assembly may need inspection before assuming this clutch is at fault.
Is this an OEM or aftermarket part?
This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine GE OEM part, but is manufactured to match the material, dimensions, and mounting configuration of the original WH05X24185 clutch used in compatible GE, Hotpoint, Haier, Monogram, and Café top-load washers.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
WH42X10650 Washer Control Panel, White
Replaces Part Numbers: WH42X10650, AP3995175, 1264621, AH1482468, EA1482468, PS1482468.
The WH42X10650 is a genuine GE replacement part, specifically designed as a control panel for GE washing machines. It houses and operates the control buttons and display, ensuring compatibility and reliability for your appliance.
EXP572 Dryer Door Catch – Aftermarket Replacement for Whirlpool, Kenmore, Maytag, GE, Hotpoint
Product Overview
This Door Catch is a replacement part for specific GE, Hotpoint dryer models. It includes the door catch. This part ensures the dryer door remains securely closed during operation, preventing heat loss and ensuring the appliance functions efficiently. Common causes of a bad door catch include regular wear and tear, physical damage, or misalignment of the door, which can impact the catch's ability to latch properly
Replaces Part Numbers
WE1M1011, PS3502777, AP5324728, WE01M0197, WE01X0889, WE01X0903, WE01X1032, WE1M187, WE1M197, WE1M536, WE1X1032, WE1X889, WE1X903. It provides a reliable fit and function similar to OEM components.
Fixes the Following Issues
Dryer door won’t stay closed
Dryer doesn’t start
Door pops open mid-cycle
Worn or damaged door catch
Compatible Brands
Compatible with dryers made by Whirlpool, Kenmore (Whirlpool-built), Maytag, Amana, Roper, Estate, GE and Crosley. Suitable for many front-load and top-load residential models.
Why Buy from Parts-O-Matic
High-quality, durable replacement part
Always Fast and Free U.S. shipping
Easy to install – no special tools required
Trusted by appliance repair professionals and DIYers
WPW10435242 Washer Genuine OEM Water Valve
Description: The Water inlet valve assembly is an OEM part for specific Whirlpool washing machine models. This valve assembly controls the flow of water entering the washing machine. It regulates water levels during different wash cycles like filling, rinsing, and draining.
Replaces Part Numbers: WPW10435242, W10435242, W10435236, AP6021375, PS11754698.
California Residents only
WARNING: California’s Proposition 65
Genuine OEM WH44X27239 Washer Tub Cover
The Genuine OEM GE WH44X27239 is the tub cover, also called a tub ring, for select GE 24-inch washer-dryer combo units. It snaps over the top of the tub and acts as a splash shield. If your cover is cracked, broken or missing, this is the replacement.
This is the original GE part, not an aftermarket equivalent. It is sold individually. Check your model number before ordering.
Quick Answer
The Genuine OEM WH44X27239 Tub Cover replaces the snap-on tub cover (splash shield) on a compatible GE 24-inch washer-dryer combo. Typical reasons to replace it: the cover is cracked, broken or missing.
When To Replace This Part
Tub cover is cracked or broken
Tub cover is missing or no longer snaps securely over the tub
Splash shield is damaged
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This tub cover is listed under the following part number:
WH44X27239, 4588351, AP6328375, AGE26665, EAP12343494, PS12343494, PD00068486
If your old cover shows a different number, contact our support team and we'll check whether it matches.
Compatibility
This tub cover is listed for GE 24-inch washer-dryer combo units, including:
GE GUD24ESSM0WW, GUD24ESSM1WW
GE GUD24GSSM0WW, GUD24GSSM1WW
Note: These are the models retailers list for this part. GE also sells other tub covers with different part numbers that look similar. Check your full model number against your parts diagram, or contact our support team to verify fit before ordering.
Key Features
Genuine OEM GE part, not an aftermarket equivalent
Snaps over the top of the tub as a splash shield
Sold individually
Product Specifications
Part Number
WH44X27239
OEM Part Number
WH44X27239
Part Type
Washer Tub Cover (Tub Ring)
Condition
Genuine OEM
Manufacturer
GE
Quantity
1 Cover
Application
Select GE 24-Inch Washer-Dryer Combos
Installation Notes
⚠️ Disconnect Power Before Installing Unplug the unit before you begin and wear work gloves. Remove the old cover and snap the new cover over the top of the tub, making sure it seats all the way around. Restore power and run a short cycle to confirm it stays in place.
Frequently Asked Questions
What does the tub cover do?
It snaps over the top of the tub and works as a splash shield.
Is this an OEM or aftermarket part?
This is a genuine OEM part from GE, not an aftermarket equivalent.
Is this for a standalone washer?
It is listed for GE 24-inch washer-dryer combo units. Match the part number and your model number before ordering, or contact our support team.
Will this fit my washer-dryer?
It is listed for GUD24ESSM0WW, GUD24ESSM1WW, GUD24GSSM0WW and GUD24GSSM1WW. If your model is not on that list, check your parts diagram or contact our support team and we'll verify it before you order.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping ✓ Genuine OEM Parts ✓ Compatibility Support ✓ Secure Checkout
