Search results for "hvac Switch"

XPARTCO 6931EL3001F Dryer Hi-Limit Thermostat The XPARTCO 6931EL3001F is an aftermarket replacement dryer rear hi-limit heater thermostat compatible with select LG and Kenmore electric and gas dryers. The hi-limit thermostat is a safety switch mounted on the heater housing that monitors the temperature at the heating element. If the heater temperature exceeds the safe operating limit, the thermostat opens its contacts to cut power to the heating element, protecting the dryer and its contents from overheating. When cooled, the thermostat resets automatically — but if it fails internally, it may remain open permanently, causing the dryer to produce no heat despite the thermal fuse and other components being intact. Rated L125-31C, 250V, 25A, this 3-terminal thermostat measures 2"L x 1-3/4"W x 1-1/4"H with approximately 1-5/8" between mounting holes (center to center). It is constructed from metal and plastic in gray/black and mounts directly on the heater housing. It directly replaces 1377779, AP5072172, AH3530482, EA3530482, EAP3530482, PS3530482, and PD00023316. Often replaced together with the 6931EL3003D thermal fuse — both mount on the heater housing and work as a system to protect the dryer from overheating. Installs in 15–20 minutes with basic hand tools. Quick Answer The XPARTCO 6931EL3001F Dryer Hi-Limit Thermostat fixes LG and Kenmore dryers with no heat where the thermostat has failed open. Rated L125-31C, 250V/25A, 3 terminals. 2"L x 1-3/4"W x 1-1/4"H, ~1-5/8" between mounting holes. Mounts on heater housing. Test with multimeter — should show closed continuity at room temperature. Often replaced together with 6931EL3003D thermal fuse. Replaces 1377779, AP5072172, AH3530482, EA3530482, EAP3530482, PS3530482. Common Problems This Part Fixes Dryer produces no heat — hi-limit thermostat has failed open and is permanently interrupting the heater circuit Dryer takes much longer than normal to dry a load Dryer tumbles normally but generates no heat during the cycle No heat even after the thermal fuse has already been replaced — thermostat also failed Dryer overheating intermittently — thermostat not opening at the correct temperature Multimeter test shows open circuit (no continuity) across the thermostat at room temperature Replaces Part Numbers This hi-limit thermostat directly replaces the following OEM and cross-reference part numbers: 6931EL3001F, 1377779, AH3530482, ALG51960, EA3530482, EAP3530482, AP5072172, PD00023316, PS3530482 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This hi-limit thermostat is compatible with select LG and Kenmore electric and gas dryers. Compatible models include LG DLE, DLG, DLEX, DLGX, and DLB series dryers, and Kenmore 796-series dryers built on the LG platform. LG electric dryers — DLE series (DLE2050W, DLE3777W, DLE5955W and related models) LG electric dryers — DLEX series (select models) LG gas dryers — DLG series (DLG2051W, DLG3788W and related models) LG gas dryers — DLGX series (select models) LG electric and gas dryers — DLB series (select models) Kenmore / Sears dryers — 796-series (LG-built models) Tip: When replacing the 6931EL3001F thermostat, also replace the 6931EL3003D thermal fuse at the same time. Both mount on the heater housing and are commonly replaced together — an overheating event that causes one to fail typically stresses both. Key Features Hi-limit heater thermostat — safety switch that cuts power to the heating element if heater temperature exceeds safe limits Auto-resets when cooled — but a failed thermostat that remains open causes permanent no-heat Rated L125-31C, 250V, 25A — correct specifications for compatible LG and Kenmore dryers 3-terminal design — matches the original wiring configuration on compatible heater housings Dimensions: 2"L x 1-3/4"W x 1-1/4"H; ~1-5/8" between mounting holes (center to center) Metal and plastic construction (gray/black) — heat-resistant materials for heater housing application Mounts directly on the heater housing — accessible from the dryer back panel Often replaced together with 6931EL3003D thermal fuse for a complete heater housing thermal repair Test with multimeter before replacing — should show closed continuity at room temperature Aftermarket replacement built to OEM-equivalent quality standards Quick DIY repair — installs in 15–20 minutes with basic hand tools Product Specifications Part Number 6931EL3001F Part Type Dryer Rear Hi-Limit Heater Thermostat Condition Aftermarket Replacement Application LG and Kenmore Electric and Gas Dryers Thermostat Rating L125-31C — auto-resets after cooling Voltage 250V Amperage 25A Terminals 3-terminal Dimensions 2"L x 1-3/4"W x 1-1/4"H Mounting Hole Spacing Approx. 1-5/8" center to center Color Gray / Black Material Metal / Plastic Location Heater housing (rear of dryer) Normal Behavior Closed continuity at room temperature Often Replaced With 6931EL3003D Thermal Fuse Compatible Brands LG, Kenmore (LG-built) Installation Notes ⚠️ Unplug Dryer and Shut Off Gas Before Starting Disconnect power (and shut off gas for gas dryers) before beginning. Remove the back panel of the dryer by unscrewing the perimeter screws to access the heater housing. The 6931EL3001F thermostat is mounted on the heater housing — it is the 3-terminal component with gray/black housing. Before removing it, test it with a multimeter: disconnect the wires and probe the terminals. At room temperature a working thermostat shows closed continuity. An open reading confirms failure. Photograph the 3-wire connections before disconnecting — reconnecting in the correct positions is important. Remove the 2 mounting screws and lift the old thermostat off. Install the new thermostat in the same position with the 2 mounting screws and reconnect the wires in the same positions. While the heater housing is accessible, also test and replace the 6931EL3003D thermal fuse if needed. Reinstall the back panel, restore power, and run a test heat cycle. Tools needed: Phillips screwdriver, multimeter. Frequently Asked Questions What is the difference between the 6931EL3001F thermostat and the 6931EL3003D thermal fuse? Both are mounted on the heater housing and protect the dryer from overheating, but they work differently. The 6931EL3001F is a resettable hi-limit thermostat rated L125-31C — it opens when the heater temperature gets too high and resets automatically when cooled. The 6931EL3003D is a one-time thermal fuse that permanently interrupts the circuit if the temperature exceeds its rated limit — once blown, it cannot reset and must be replaced. Both should show closed continuity at room temperature when working. Because both are on the heater housing and experience the same thermal stress, replacing both at the same time is recommended. How do I test the 6931EL3001F thermostat with a multimeter? Unplug the dryer and disconnect all three wires from the thermostat terminals. Set your multimeter to continuity or resistance mode. At room temperature, a working 6931EL3001F thermostat should show closed continuity (near-zero resistance) across its contacts. If your multimeter reads open circuit (no continuity / OL), the thermostat has failed and needs replacement. Since this thermostat auto-resets when cooled, always test at room temperature — testing while the dryer is still warm may give a false open reading if the thermostat has legitimately opened due to heat. My LG dryer has no heat but the thermal fuse is good — could it be the thermostat? Yes — when the thermal fuse tests good but there is still no heat, the hi-limit thermostat (6931EL3001F) is the next most common culprit. A thermostat that has failed internally may remain permanently open even at room temperature, cutting power to the heating element exactly as a blown thermal fuse would. Test the thermostat with a multimeter for continuity. Also check the cycling thermostat (6931EL3002M) and the thermistor (6323EL2001B) — all three are part of the LG dryer thermal control system and any one of them can cause a no-heat condition. What does the "L125-31C" rating mean? The L125-31C rating describes the thermostat's operating parameters. L125 means the thermostat opens (trips) when the temperature reaches approximately 125°C (257°F). The 31 indicates the reset differential — the thermostat resets when the temperature drops approximately 31°C below the trip point, around 94°C (201°F). This rating ensures the thermostat allows the heater to operate at normal drying temperatures while protecting against dangerous overheating. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine LG OEM part, but is manufactured from metal and plastic to match the L125-31C rating, dimensions, and 3-terminal configuration of the original 6931EL3001F hi-limit heater thermostat. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

Genuine OEM WP3387134 Dryer Cycling Thermostat The Genuine OEM Whirlpool WP3387134 is a dryer cycling thermostat, the operating thermostat that controls drying temperature. It switches the heating element off when the dryer reaches its set temperature and back on after it cools, keeping the inside of the dryer at a steady temperature throughout the cycle. This one is rated L155-25: it cuts out at approximately 155°F and cycles back on once the temperature drops about 25°F. When a cycling thermostat fails, the dryer may stop heating, run too hot, or keep heating after the drum has stopped. This is the original Whirlpool part, and it fits a wide range of Whirlpool-built dryers sold under the Whirlpool, Kenmore, Maytag, KitchenAid, Roper, Crosley, Estate, Amana, and other brand names. Quick Answer The Genuine OEM WP3387134 Cycling Thermostat fixes a Whirlpool-built dryer that isn't heating, runs too hot, or has inconsistent drying temperatures. Rated L155-25, it cycles the heating element off at about 155°F and back on after a 25°F drop. Classic symptom: clothes come out damp or the dryer runs excessively hot, with no sign of a clogged vent. Common Problems This Part Fixes Dryer not heating Dryer running too hot Inconsistent drying temperatures Heat staying on after the drum has stopped Dryer won't start or the timer doesn't advance, if the thermostat has failed Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This cycling thermostat directly replaces the following part numbers: WP3387134, 3387134, 2011, 2893, 3-6910, 306910, 3387135, 3387139, ET187,  EAP11741405, WP3387134VP, AP6008270, AWP47432, EAP11741405, PD00002313, PS11741405, L155-25F These numbers span several generations of Whirlpool's own part numbering for this thermostat as model lines were updated. All are the correct replacement regardless of which number appears on your dryer's parts diagram. Compatibility This thermostat fits a wide range of Whirlpool, Kenmore, Maytag, KitchenAid, Roper, Crosley, Estate, Amana and related dryers, including these examples: Kenmore 11060012000, 11060012001, 11060022010, 11060172000, 11060232000, 11060602990 Numerous additional Whirlpool-built dryer models Note: This is the cycling (operating) thermostat, not the high limit thermostat or the thermal fuse, which are separate safety parts. The models above are a sample, not a full list. Confirm your model number against your dryer's parts diagram, or contact our support team to verify fit before ordering. Key Features Genuine OEM Whirlpool cycling thermostat Rated L155-25: cuts out at about 155°F and cycles back on after a 25°F drop Keeps dryer temperature steady by cycling the heating element on and off Resolves no-heat, overheating, and inconsistent-temperature symptoms Fits Whirlpool, Kenmore, Maytag, KitchenAid, and other Whirlpool-built dryers Medium-difficulty repair with basic hand tools Product Specifications Part Number WP3387134 OEM Part Number WP3387134 Part Type Dryer Cycling Thermostat Condition Genuine OEM Temperature Rating L155-25 (Cuts Out ~155°F, 25°F Differential) Application Whirlpool, Kenmore, Maytag, KitchenAid & Related Dryers Installation Notes ⚠️ Unplug Power Before Installing Unplug the dryer or switch off its circuit breaker before beginning, and shut off the gas supply first on gas models. Wear work gloves, as the cabinet edges are sharp. Remove the panel that gives access to the heater housing per your model's service guide, note the wire terminal positions, and disconnect them from the old thermostat. Remove the thermostat, install the new one in the same position, and reconnect the wires. A screwdriver and needle-nose pliers are typically all you need. Before closing the dryer, clean the lint trap and check the exhaust vent for restrictions, since poor airflow is a common cause of overheating. Frequently Asked Questions My dryer isn't heating or runs too hot. Is this the part I need? A failed cycling thermostat can cause either symptom. It may stay open and prevent heat, or stay closed and let the dryer overheat. Check for a clogged vent and test the thermostat for continuity before replacing it. What's the difference between the cycling thermostat and the high limit thermostat? The cycling thermostat controls normal drying temperature by switching the heating element on and off. The high limit thermostat and thermal fuse are separate safety devices that cut power if the dryer overheats. This listing is for the cycling thermostat only. How do I test this thermostat? With the dryer unplugged and the wires removed, check for continuity across the terminals with a multimeter at room temperature. A properly working cycling thermostat should show continuity when cool. No continuity means it has failed. Will this fit my dryer? It fits many Whirlpool-built dryers, but the model list above is only a sample. Check your model number against your parts diagram, or contact our support team and we'll verify it before you order. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Genuine OEM Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

4TM-C12 Refrigerator / Freezer Compressor Overload 1/2 HP Refrigerator / Freezer Thermal Overload Protector 1/2 HP (375W) - 110V 4TM-C Replaces Part Numbers: 6750C-0004R, AP4651578, PS3529535, 6750C-0005P, AH3529540, EA3529540, AP4439459, PS3529540.   This is an aftermarket part that can be used as a replacement for the OEM part.

Read more less

Genuine Whirlpool OEM Whirlpool WPW10184813 Refrigerator Genuine OEM Ice Dispenser Motor Genuine OEM ice-dispenser door motor for select Whirlpool-built refrigerators. Product Overview The Whirlpool WPW10184813 Refrigerator Ice Dispenser Door Motor is a Genuine Whirlpool OEM replacement part. It opens and closes the ice chute door during dispenser operation so ice can pass through the chute and the door can reseal afterward. A failed motor can cause the dispenser door to remain stuck open or closed, prevent ice from dispensing correctly, or allow warm room air to enter the chute area. Quick Answer WPW10184813 is the Genuine Whirlpool OEM ice-dispenser door motor that replaces W10184813 and 2305262. Verify the complete refrigerator model number before purchase. Common Problems This Part May Fix Ice dispenser door will not open Ice chute door will not close Ice maker makes ice but ice will not dispense Chute door sticks or operates intermittently Warm air enters around the dispenser chute Frost or moisture develops around the dispenser opening Replaces and Cross-References WPW10184813, 1489085, 2305262, AP6016508, EAP11749796, W10184813, AWP49407, OEM18049533, PD00006398, PS11749796 Cross-reference numbers are provided for identification. Always verify compatibility by complete refrigerator model number. Compatibility Used on select Whirlpool-built refrigerators sold under Whirlpool, KitchenAid, JennAir, Maytag, and Kenmore brand names. Compatible model examples include: GI7FVCXWY00 KSCS25FTMS02 KSRS25FTSS01 KSCS23FVMS02 KSRS25RSBT01 KSCS25FVMS01 KSCS25FTSS00 GC3NHAXVA00 106.56702500 Important: This is only a partial model list. Confirm the complete model number from the refrigerator identification label before ordering. Key Features Genuine Whirlpool OEM part Operates the ice dispenser chute door Replaces W10184813 and 2305262 For select Whirlpool-built side-by-side and French-door refrigerators Helps restore proper dispenser-door opening and closing Product Specifications Manufacturer Part Number WPW10184813 Brand Whirlpool Part Type Refrigerator Ice Dispenser Door Motor Condition New Quality Genuine OEM Application Ice Dispenser Chute Door Package Quantity 1 Motor Installation Notes Disconnect refrigerator power before service. Remove the dispenser trim and front components according to the appliance service procedure. Photograph connector and mechanical linkage positions before disassembly. Inspect the chute door, hinge, spring, and linkage for binding or damage before replacing the motor. Transfer or reconnect the wiring and linkage exactly as originally installed. Reassemble all dispenser parts and verify the chute door opens and fully closes before returning the refrigerator to service. Diagnostic tip: A dispenser that will not release ice can also be caused by an actuator, dispenser switch, control board, auger motor, frozen chute, or mechanical obstruction. Diagnose the dispenser system before replacing parts. Frequently Asked Questions Is WPW10184813 a Genuine Whirlpool OEM part? Yes. WPW10184813 is a Genuine Whirlpool OEM ice-dispenser door motor. Does it replace W10184813? Yes. Whirlpool lists WPW10184813 as the replacement for W10184813 and 2305262. What does this motor do? It opens and closes the dispenser chute door so ice can pass through the chute and the opening can reseal after dispensing. Will it fit every Whirlpool refrigerator? No. Verify the complete refrigerator model number before ordering because dispenser designs vary by model and production revision. Shop With Confidence Genuine Whirlpool OEM replacement part. Verify your complete refrigerator model and original part number before ordering. Genuine OEMIce Dispenser MotorCompatibility SupportFast U.S. Shipping

Read more less

XPARTCO 53-1096 Gas Dryer Thermostat - Compatible with Maytag, Amana, Magic Chef, Jenn-Air Dryers Product Description Keep your gas dryer safe and operational with the replacement 53-1096 Gas Dryer Thermostat. This high-limit thermostat is designed for select Maytag, Amana, Magic Chef, and Jenn-Air gas dryers, preventing overheating by shutting off the burner at 240°F and restarting at 200°F. It addresses issues like no heat, overheating, or premature shutoff, offering a cost-effective alternative to OEM parts. Note: Includes one high-limit thermostat. Disconnect power and gas supply before installation. Often paired with thermal fuses (e.g., 53-1182, 53-0771) for comprehensive repairs. Replaces part numbers: WP53-1096, 53-1096, PD00055179, AP6009640, PS11742808. Compatibility: Compatible with models including but not limited to: Maytag: DG312, DG612, DG712, LDG7304AAL, LDG8604AAL, MDE3000AYW Amana: NGD7200TW10, 4GNED4400YQ2 Magic Chef: CYG1005AXX, CYG2000AWW Jenn-Air: JDE1000W, JDG1000W Verify your model number or contact our support team for assistance. Key Features: ✅ Brand and Models Compatibility: Fits select Maytag, Amana, Magic Chef, Jenn-Air, Norge, Admiral, and Crosley gas dryers. 🔥 Specifications: replacement high-limit thermostat, opens at 248°F, closes at 200°F, 25A at 240VAC. 💰 Cost-Effective Alternative: Offers OEM-equivalent performance at a lower price. 🛠️ Easy Installation: Requires Phillips screwdriver, pliers, work gloves; typically installed in 15–20 minutes. 🛡️ Effective Fixes: Resolves no heat, overheating, or premature shutoff issues. Product Specification Part Number: 53-1096 Component Type: High-limit thermostat Material: Metal and plastic Mounting: Two 1/4" male spade terminals, includes mounting bracket Operating Conditions: Suitable for high-temperature gas dryer environments Compliance: Prop 65 warning for California Installation Notes: Safety First: Disconnect the dryer from the power source and gas supply before installation. Shop for high-quality replacement appliance parts with a 30-day return policy. Keep your dryer running safely today! Add to cart now for a budget-friendly fix!

Read more less

DC47-00018A CM Dryer Thermostat L260-50F. 125/250V. 25A. 1/4" spade terminals. Used on DC97-14486A elements. Replaces Parts Numbers: DC47-00018A, 1122485, AP4201898, PS4205217. Description: This High Limit Thermostat is a replacement part for specific Samsung dryer models. It plays a role in the safety and efficiency of the dryer's operation by monitoring and regulating the temperature within the dryer. This thermostat acts as a safety device, cutting off the heat source if the internal temperature exceeds safe levels, preventing potential overheating and fire hazards.   This is an aftermarket part that can be used as a replacement for the OEM part.

Read more less

Choice 4389102 Refrigerator Ice Level Control Board Replaces W11629974 The Choice 4389102 is a Choice-tier replacement ice level control board kit for Whirlpool refrigerators, and also fits select Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models with a vertical ice container in the freezer door. This kit uses an infrared beam between an emitter and receiver board to sense the level of ice in the ice bucket, signaling the ice maker to produce more ice when the level drops and to stop when the bucket is full. Weighs approximately 0.23 lbs. Common causes of failure include electrical problems, general wear and tear, or damage from power surges or short circuits. Symptoms of a failing ice level control board include the ice maker not producing ice, the ice maker not stopping production when full, irregular or inconsistent ice production, or error codes related to the ice maker control system. It directly replaces W11629974, W10757851, 4389102, 2198585, 2198586, 2220398, 2220402, 2255114, 4388635, 4389102R, W10193666, W10193840, W10290817, W11553040, W11553041, AP7205486, AWP45901, EAP16875489, PD00086112, PS16875489. Quick Answer The Choice 4389102 Refrigerator Ice Level Control Board fixes Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore refrigerators where the ice maker isn't producing ice, won't stop when full, or produces ice inconsistently. Emitter and receiver board kit — both boards need replacing together. Replaces W11629974, W10757851, 4389102, 2198585, 2198586, 2220398, 2220402, 2255114, 4388635, 4389102R, W10193666, W10193840, W10290817, W11553040, W11553041, AP7205486, AWP45901, EAP16875489, PD00086112, PS16875489. Control boards are commonly misdiagnosed — check more commonly defective parts first, and use the LED status light blink pattern to confirm this board is actually at fault before replacing it. What's In The Kit Component Function Emitter Board Sends an infrared beam across the ice bucket opening. Receiver Board Detects whether the beam is blocked by ice, signaling the ice maker to start or stop production. Both boards need to be replaced together — this is a matched emitter/receiver pair, not two independently interchangeable parts. What Is a Choice Part? Choice parts are manufactured by a different supplier than the original appliance manufacturer, offering a dependable, cost-effective alternative to Genuine OEM parts. Unlike our OE parts, which come from the same supplier as the original manufacturer, Choice parts are made by an independent manufacturer to equivalent fit, form, and function specifications. This makes them a smart option when you want a reliable repair at a lower price point than Genuine OEM. Common Problems This Kit Fixes Ice maker not producing ice Ice maker not stopping production when the bucket is full Irregular or inconsistent ice production Error codes related to the ice maker control system Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This refrigerator ice level control board kit directly replaces the following OEM and cross-reference part numbers: W11629974, W10757851, 4389102, 2198585, 2198586, 2220398, 2220402, 2255114, 4388635, 4389102R, W10193666, W10193840, W10290817, W11553040, W11553041, AP7205486, AWP45901, EAP16875489, PD00086112, PS16875489 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This ice level control board kit is compatible with select Whirlpool refrigerators with a vertical ice container in the freezer door, and also fits select Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore refrigerators built on the Whirlpool platform, including model numbers such as KSRI25FNWH01, ED5FHAXSQ01, KSRG25FVMS05, KSRU25FKWH03, KSRK25XLSS10, JBSS42E22L00, JBSS48E22L00, KBSD702MPS00, KBSD702MSS00, KBSD706MPS00, KBSD708MBS00, KBSD708MPS00, KBSD708MSS00, and Kenmore 106.57979700, 106.51552103, and 106.58169704. Note: This kit is specifically for refrigerators where ice cubes dump directly into an ice bin located in the freezer door. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Choice-tier replacement ice level control board kit — includes matched emitter and receiver boards Resolves "no ice production," "won't stop when full," and "inconsistent ice production" symptoms Uses an infrared beam to detect ice level in the bucket Direct drop-in replacement matching the original mounting and connections Replaces W11629974, 2198585, 2198586, 2220398, 2220402, 2255114, 4388635, 4389102R, TJ4389102R, W10193666, W10193840, W10290817, W10757851, W11553040, W11553041, AP7205486, AP5956767, AP3137510, PS557945, PS10064583, EAP16875489, PS16875489, AWP45901, and PD00086112 Compatible with Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore refrigerators Manufactured by an independent supplier to equivalent fit, form, and function specifications DIY-friendly repair, typically 10 to 20 minutes Product Specifications Part Number 4389102CM OEM Part Number W11629974 Part Type Refrigerator Ice Level Control Board Kit (Emitter & Receiver) Designation Choice Weight Approx. 0.23 lbs Function Uses an infrared beam to sense ice level and signal the ice maker Application Refrigerators with vertical ice container in freezer door Repair Difficulty Easy — 10 to 20 minutes Quantity 1 kit (emitter + receiver board) Compatible Brands Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, Kenmore Installation Notes ⚠️ Unplug Refrigerator Before Starting — Confirm With The LED Test Before Replacing Unplug the refrigerator and safely store any food that could spoil while the power is off. Wear work gloves. Before installing this kit, confirm the boards are actually at fault: with the refrigerator still plugged in, check the status light on the control board — it should blink twice, pause, then repeat during normal operation. With the freezer door open, hold down the flapper door on the left side to block the optics beam; the LED should light up and stay on with no blinks. If it continues to blink twice instead, the optics control board has failed. If there's no LED light at all, hold down the freezer light switch — the LED should flash every second while in harvest mode; if it doesn't light up, the board has failed. Once confirmed, unplug the refrigerator, locate the emitter and receiver boards near the ice bucket opening in the freezer door, and disconnect their wiring. Remove the mounting screws or clips securing the old boards and take them out. Install both new boards from this kit in the same positions, reconnect the wiring fully, and secure the mounting hardware. Restore power and monitor ice production over the next day or two to confirm normal operation. Tools needed: Phillips screwdriver, work gloves. Frequently Asked Questions My ice maker stopped making ice. Is this the part I need? Possibly, but control boards are commonly misdiagnosed. Before replacing this board, check more commonly defective parts first — such as the water inlet valve, ice maker assembly itself, or the freezer temperature. If you've ruled those out and the other components are working properly, this control board is a reasonable next step. How can I confirm this board has actually failed before replacing it? Check the LED status light's blink pattern. During normal operation it should blink twice, pause, then repeat. With the freezer door open, hold down the flapper door on the left side to block the beam — the light should turn solid with no blinking. If it keeps blinking twice instead, or doesn't light up at all when it should be in harvest mode (checked by holding the freezer light switch), the board has failed. Do I need to replace just the emitter or receiver, or both? Both. This kit includes a matched emitter and receiver board, and both need to be replaced together as a pair rather than swapping just one side. What does "Choice" mean for this part? Choice parts are manufactured by an independent supplier, different from the appliance's original manufacturer, and built to equivalent fit, form, and function specifications. This gives you a dependable, lower-cost alternative to a Genuine OEM part, distinct from our OE parts, which are sourced from the same supplier as the original manufacturer. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Choice Quality Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO BPV-31 Refrigerator Refrigerant Piercing Valve / Line Tap Valve Kit The XPARTCO BPV-31 is a universal bullet piercing tap valve (line tap valve) used to quickly access a sealed refrigerant line on refrigerators, freezers, window air conditioners, dehumidifiers, and other HVAC systems — without soldering or brazing. The valve clamps around a copper refrigerant line and, when the valve stem is tightened with the included hex key, a hardened piercing needle punctures the tubing to create an access port. This lets a technician connect a charging hose or gauge to check pressure, pull a vacuum, or add refrigerant to a system that has no factory service port. It's a staple tool for appliance service and DIY refrigerator/freezer repair. Fits 1/4", 5/16", and 3/8" outside diameter copper pipes with the included adapters. The access port connection is a 1/4" male flare fitting. Rated to 500 PSI maximum, with a patented permanent gasket providing over 180 inch-lbs of sealing force — around 50 times the sealing area of a standard O-ring type valve — pressure tested at 250°F. Corrosion-resistant metal (zinc alloy) construction with a piercing needle engineered for concentricity and hardness to seat perfectly every time. Non-positional mounting requires no separate adapter valve and only 2" of clearance for installation. Each kit includes the piercing valve, a hex key wrench, and 2 adapters. It replaces AP4502525, BPV31, BPV31D, GPV14, GPV31, GPV38, GPV56, and MPV31. Quick Answer The XPARTCO BPV-31 Refrigerant Piercing Valve Kit taps into a sealed copper refrigerant line to add refrigerant, check pressure, or pull a vacuum — no soldering required. Fits 1/4", 5/16", and 3/8" OD pipes. 1/4" male flare port connection. 500 PSI max, patented gasket (50x the sealing area of an O-ring). Zinc alloy metal. Includes piercing valve, hex key, and 2 adapters; only needs 2" clearance. Replaces AP4502525, BPV31, BPV31D, GPV14, GPV31, GPV38, GPV56, MPV31. Not suitable for R410a systems. Common Uses This Kit Serves Adding refrigerant to a refrigerator or freezer that has no factory service port Checking system pressure on a sealed refrigerant line for diagnostics Pulling a vacuum on a system during service Recharging window air conditioners and dehumidifiers Confirming whether a sealed system has lost its refrigerant charge (leak diagnosis) Providing temporary or service access to copper refrigerant tubing without brazing Reviving a garage/shop refrigerator or freezer that has slowly lost its charge Accessing R-12, R-22, R-134a, and other compatible refrigerant systems (NOT R410a) Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This bullet piercing tap valve directly replaces the following OEM and cross-reference part numbers: BPV-31, BPV31, BPV31D, AP4502525, GPV14, GPV31, GPV38, GPV56, MPV31 The BPV-31 is a universal valve that covers the GPV-series (GPV14, GPV31, GPV38, GPV56) and MPV31 across the pipe sizes they individually served. Contact our support team if you need help confirming the correct valve for your line size. Compatibility This bullet piercing valve is a universal tool compatible with sealed refrigerant systems using copper tubing, including: Refrigerators and freezers — all major brands with 1/4", 5/16", or 3/8" OD copper refrigerant lines Window air conditioners — for recharging and pressure checks Dehumidifiers — sealed refrigerant systems Other HVAC systems with compatible copper line sizes Refrigerant compatibility — works with R-12, R-22, R-134a and other common refrigerants Important — NOT for R410a Systems: This BPV-31 piercing valve is NOT rated for R410a refrigerant systems, which operate at significantly higher pressures than the valve's design allows. Using it on an R410a system is unsafe. Before use, confirm your line's outside diameter (1/4", 5/16", or 3/8") and select the correct included adapter. Verify the pipe size before installation. Key Features Bullet piercing tap valve — taps a sealed copper refrigerant line to create an access port without soldering or brazing Fits 1/4", 5/16", and 3/8" outside diameter copper pipes (with included adapters) 1/4" male flare access port connection for charging hoses and gauges 500 PSI maximum pressure rating Patented permanent gasket — over 180 inch-lbs of sealing force, ~50 times the sealing area of a standard O-ring type valve; pressure tested at 250°F Piercing needle engineered for concentricity and hardness to seat perfectly every time Corrosion-resistant zinc alloy metal construction — won't rust or wear out over time Non-positional mounting — no separate adapter valve required, installs in any orientation Compact design needs only 2" of clearance for installation and use Each kit includes: 1 piercing valve, 1 hex key wrench, 2 adapters Replaces AP4502525, BPV31, BPV31D, GPV14, GPV31, GPV38, GPV56, and MPV31 NOT suitable for R410a refrigerant systems Product Specifications Part Number XPBPV-31 Part Type Bullet Piercing Tap Valve (Line Tap Valve Kit) Condition Aftermarket Replacement Application Refrigerators, Freezers, Window AC, Dehumidifiers, HVAC (sealed copper lines) Compatible Pipe Sizes 1/4", 5/16", 3/8" outside diameter Port Connection 1/4" Male Flare Maximum Pressure 500 PSI Sealing Force 180+ inch-lbs (patented gasket, ~50x O-ring sealing area) Pressure Tested 250°F Material Corrosion-resistant zinc alloy metal Mounting Non-positional, 2" clearance required Kit Includes 1x Piercing Valve, 1x Hex Key, 2x Adapters Not Compatible With R410a refrigerant systems Installation Notes ⚠️ Refrigerant Safety Warning Working with sealed refrigerant systems can expose you to pressurized refrigerant, which can cause frostbite, eye injury, and other harm. Wear safety glasses and protective gloves before piercing any line. Refrigerant handling may be regulated in your area — certain refrigerants require EPA certification (in the US) to purchase and handle. Never vent refrigerant to the atmosphere. This valve is NOT rated for R410a systems (too high pressure). If you're not experienced with refrigerant systems, have this work done by a qualified HVAC or appliance technician. ⚠️ Installation Steps — Clean the Line First Put on safety glasses and protective gloves. Identify the copper line you want to tap and confirm its outside diameter (1/4", 5/16", or 3/8") so you can select the correct included adapter. Clean the section of pipe where the valve will mount to prevent debris from entering the refrigerant line. Ensure the composite seal "O" ring/gasket is properly in place inside the valve. Place the two halves of the valve saddle around the pipe using the appropriate adapter insert for your pipe size. Install and evenly tighten the socket-head screws to clamp the valve body firmly around the pipe. To pierce the line, turn the valve stem clockwise with the included hex key until the needle punctures the tubing, then back the stem out (counterclockwise) to open the port and allow flow. To connect a gauge or charging hose: remove the cap, attach your hose to the 1/4" flare port, and open the valve by turning the stem counterclockwise. When finished, close the valve (turn the stem clockwise) BEFORE disconnecting the hose, then reinstall the protective cap. Note: the compact valve needs only 2" of clearance around the pipe. Tools needed: Included hex key wrench, safety glasses, protective gloves. (Note: to attach a gauge directly to the BPV, a retrofit valve adapter may be required — not included.) Frequently Asked Questions What is a bullet piercing valve used for? A bullet piercing valve (line tap valve) lets you tap into a sealed copper refrigerant line to create an access port — without cutting, soldering, or brazing the line. Most household refrigerators and freezers are sealed systems with no factory service port, so if you need to check the refrigerant pressure, pull a vacuum, or add refrigerant, a piercing valve gives you that access quickly. It clamps around the pipe, and a needle pierces the tubing when you tighten the valve stem. It's commonly used in appliance repair and HVAC service, and by DIYers reviving a garage refrigerator or freezer that has lost its charge. Which pipe sizes does this fit? The BPV-31 fits 1/4", 5/16", and 3/8" outside diameter copper pipes using the included adapters. Before installing, measure or confirm your refrigerant line's outside diameter and select the matching adapter insert. Getting the size right is essential for a proper seal — an incorrectly sized adapter won't clamp tightly and can leak. If you're not sure of your line size, measure the outside diameter of the copper tubing with calipers or a pipe gauge. Can I use this on an R410a system? No — the BPV-31 is NOT rated for R410a refrigerant systems. R410a operates at significantly higher pressures than older refrigerants like R-12, R-22, and R-134a, and exceeds the safe working pressure of this valve (500 PSI max). Using it on an R410a system is unsafe and could result in valve failure or refrigerant release. This valve is appropriate for lower-pressure systems using R-12, R-22, R-134a, and similar refrigerants. For R410a systems, use service equipment specifically rated for R410a pressures. Is a piercing valve a permanent solution? Piercing valves are best thought of as a service-access tool rather than a permanent fixture. They work reliably for tapping into a line to diagnose, vacuum, or charge a system, and the BPV-31's patented gasket provides a much stronger seal than basic O-ring valves. However, for a long-term permanent service port, many technicians prefer to cut the line and braze in a proper Schrader service port. Some technicians have concerns about the very long-term sealing of any piercing valve left permanently on a line. If you leave the valve installed, make sure the stem is closed and the cap is in place, and check periodically for leaks. Do I need EPA certification to add refrigerant? In the United States, handling many refrigerants (and purchasing them) requires EPA Section 608 certification, and it is illegal to intentionally vent refrigerant to the atmosphere. Regulations vary by refrigerant type and jurisdiction. The piercing valve itself is a tool that anyone can install, but the refrigerant handling that follows may be regulated. If you're a DIYer, research the rules that apply to your specific refrigerant and location, or have the refrigerant work done by a certified technician. Always recover refrigerant properly rather than venting it. Is this an OEM or aftermarket part? This is an aftermarket universal service tool built to OEM-equivalent quality standards. The BPV-31 is a universal industry-standard bullet piercing valve design (also sold as Supco BPV31 and equivalent), manufactured from corrosion-resistant zinc alloy to match the fit, 1/4"/5/16"/3/8" pipe compatibility, 1/4" flare port, 500 PSI rating, and patented-style sealing gasket of the standard BPV-31 line tap valve. It replaces AP4502525, BPV31D, GPV14, GPV31, GPV38, GPV56, and MPV31. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

WR50X10068 Refrigerator Defrost Thermostat – Replacement for GE, Hotpoint, and Kenmore Product Overview This Defrost Thermostat is a replacement part designed for use in select GE refrigerator models. This component acts as a safety device in the refrigerator's defrost system, preventing the freezer from overheating during the defrost cycle. It works by monitoring the temperature of the evaporator coil and turning off the defrost heater when the coil gets warm enough, thus safeguarding the freezer from getting too hot.  Defrost thermostat for refrigerator or freezer L140-30F. 6" long wire, wire connectors not included. Replaces Part Numbers This thermostat replaces WR50X10068, WR50X10015, WR50X10017, WR50X10018, WR50X10028, WR50X10051, WR50X10052, WR50X10053, WR50X10054, WR50X10074, WR50X10075, WR50X10079, L140-30F, AH1017716, EA1017716, AP3884317, PS1017716.  It is designed to match OEM performance and fit in a wide range of GE and GE-built refrigerator models. Compatible Brands Compatible with refrigerators from GE, Hotpoint, and Kenmore models manufactured by GE. Suitable for top-freezer and side-by-side configurations that use a defrost thermostat with this part number. Fixes the Following Issues Frost or ice buildup in freezer Refrigerator not defrosting Poor airflow and cooling performance Defrost cycle not activating Why Buy from Express Parts Direct Cost-effective aftermarket alternative Fast and free shipping across the U.S. Trusted by appliance technicians and DIY users Easy to install and reliable in performance

Read more less

XPARTCO W10316760 Refrigerator Thermistor Sensor The XPARTCO W10316760 is an aftermarket replacement temperature thermistor compatible with a wide range of Whirlpool-built refrigerators sold under the Whirlpool, KitchenAid, Maytag, Jenn-Air, Amana, Inglis, and Magic Chef brands. The thermistor sits inside the fresh food or freezer compartment and continuously reports internal temperature back to the electronic control board, which uses that reading to cycle the compressor, evaporator fan, and damper to keep the compartment in range. When the thermistor drifts out of calibration or fails outright, the control board loses an accurate temperature signal and the refrigerator commonly responds with erratic cooling, a warmer-than-normal compartment, food freezing when it shouldn't, or a flashing/blank temperature display. This XPARTCO version is built with a quick-connect mounting clip, so it plugs in without cutting or splicing wires — unlike the genuine Whirlpool OEM part, which ships as a splice-in kit requiring you to cut the old thermistor's leads and join the new ones with included wire connectors. It directly replaces W10316760, WPW10323459, W10323459, 12791417, 12791417SP, 12791419SP, 1876627, W10280385, W10280386, W10308052, W10316760VP, W10438639, W10438761, W10452402, AH2580944, AP4538142, AWP40532, EA2580944, EAP2580944, PD00006590, PS2580944, and additional cross-reference numbers listed below. Installs in 15–30 minutes with basic hand tools. Quick Answer The XPARTCO W10316760 Refrigerator Thermistor Sensor fixes Whirlpool, KitchenAid, Maytag, Jenn-Air, Amana, Inglis, and Magic Chef refrigerators that are running warm, running constantly, freezing food unexpectedly, or showing a flashing/blank temperature display. This version uses a quick-connect clip — no wire cutting or splicing like the genuine Whirlpool splice-kit version requires. Replaces W10316760, WPW10323459, W10323459, 12791417, 12791417SP, 12791419SP, 1876627, W10280385, W10280386, W10308052, W10316760VP, W10438639, W10438761, W10452402, AH2580944, AP4538142, AWP40532, EA2580944, EAP2580944, PD00006590, PS2580944. Classic symptom: fridge or freezer running warmer than the setting, or running nonstop. Common Problems This Part Fixes Refrigerator or freezer running noticeably warmer than the temperature setting Fridge running constantly and never cycling off Temperature display flashing, showing dashes, or displaying an error code Food freezing in the fresh food compartment when it shouldn't be Compressor and fans not cycling normally, or running nonstop Inconsistent or swinging temperature readings on the display One compartment (fridge or freezer) running warm while the other stays normal Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This refrigerator thermistor directly replaces the following OEM and cross-reference part numbers: W10316760, WPW10323459, W10323459, 12791417, 12791417SP, 12791419SP, 1876627, W10280385, W10280386, W10308052, W10316760VP, W10438639, W10438761, W10452402, AH2580944, AP4538142, AWP40532, EA2580944, EAP2580944, PD00006590, PS2580944 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This thermistor is used across a wide range of Whirlpool-built refrigerators from the following brands: Whirlpool refrigerators (including WRF535SMBM00, WRX735SDBM00, and related French door / side-by-side models) KitchenAid refrigerators (including KBFS22EWBL1, KBFS22EWMS1, KBFS22EWMS3, KBFS22EWMS5, KBFS22EWMS7, KBFS22EWWH1) Maytag refrigerators (select Whirlpool-built models, including KRFF302ESS) Jenn-Air refrigerators (select Whirlpool-built models, including MFI2269VEM) Amana refrigerators (select models) Inglis refrigerators (select models) Magic Chef refrigerators (select models) Note: Many of these refrigerators use separate thermistors for the fresh food and freezer compartments, so confirm which sensor location your model uses before ordering — appearance can be similar across positions. Always verify your appliance model number before ordering. Contact our support team with your model number if you're unsure. Key Features Direct-fit replacement refrigerator temperature thermistor — reports compartment temperature to the electronic control board Resolves "running warm," "running constantly," "freezing food," and "flashing display" symptoms caused by thermistor failure Quick-connect mounting clip — no wire cutting or splicing required Matches OEM electrical resistance curve for accurate temperature sensing Approximate lead length ~5 inches Replaces W10316760, WPW10323459, W10323459, 12791417, 12791417SP, 12791419SP, 1876627, W10280385, W10280386, W10308052, W10316760VP, W10438639, W10438761, W10452402, AH2580944, AP4538142, AWP40532, EA2580944, EAP2580944, PD00006590, PS2580944, and additional cross-reference numbers Compatible with Whirlpool, KitchenAid, Maytag, Jenn-Air, Amana, Inglis, and Magic Chef refrigerators Aftermarket replacement built to OEM-equivalent quality standards Quick DIY repair — installs in 15–30 minutes with basic hand tools Product Specifications Part Number XPW10316760 OEM Part Number W10316760 Part Type Refrigerator Temperature Thermistor / Sensor Condition Aftermarket Replacement Application Whirlpool-Built Refrigerators (Fresh Food / Freezer Compartment) Mounting Quick-connect clip (no splicing) Approx. Lead Length ~5 inches (may vary by model) Compatible Brands Whirlpool, KitchenAid, Maytag, Jenn-Air, Amana, Inglis, Magic Chef Installation Notes ⚠️ Disconnect Power Before Starting Unplug the refrigerator or shut off power at the breaker before accessing internal panels. Locate the thermistor at its mounting position inside the fresh food or freezer compartment (location varies by model — consult your model's parts diagram if unsure). Photograph the wire routing before disconnecting. On this XPARTCO version, simply unplug the old thermistor's connector from the wiring harness — no cutting or splicing needed. Release the old thermistor from its mounting clip or bracket and remove it. Install the new thermistor in the same position, securing it in its mounting clip. Plug the new thermistor's connector into the wiring harness, matching your photos. Reassemble any panels removed for access. Restore power and allow the refrigerator several hours to stabilize before checking temperatures. Tools needed: nut driver or screwdriver (for panel access), needle-nose pliers (for mounting clip). Frequently Asked Questions Is this the same as the genuine Whirlpool W10316760 thermistor? It's a direct-fit aftermarket equivalent, not the genuine Whirlpool part. The key functional difference is installation: the genuine OEM version ships as a splice-in kit requiring you to cut the old wires and use included splice connectors, while this XPARTCO version has a quick-connect clip that simply plugs in — no splicing tools needed. Will this fit my refrigerator? W10316760 and its cross-reference numbers span a wide range of Whirlpool-built models across several brands. Confirm fit using your refrigerator's exact model number before ordering, since visually similar thermistors are used across different platforms and compartment locations. Contact our support team with your model number if you're unsure. My fridge is warm but the freezer is fine (or vice versa) — could this part be the cause? Yes. Most of these refrigerators use separate thermistors for the fresh food and freezer compartments, so a single failed sensor can cause one section to run warm while the other stays normal. Confirm which sensor location your model uses before ordering. Do I need any tools to install this? Basic hand tools to access the interior panel (typically a nut driver or screwdriver) plus needle-nose pliers to release the old mounting clip. Because this version uses a plug-style connector, no wire strippers, cutters, or splice connectors are needed — unlike the genuine OEM splice-kit version. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured to match the electrical resistance curve, mounting position, and temperature-sensing function of the original W10316760 thermistor used in compatible Whirlpool, KitchenAid, Maytag, Jenn-Air, Amana, Inglis, and Magic Chef refrigerators. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO WR07X10097 Refrigerator Compressor Overload Relay – Compatible with GE, Hotpoint, and Kenmore Refrigerators Product Description Restore proper compressor protection and reliable cooling with the XPARTCO WR07X10097 Refrigerator Compressor Overload Relay. This Start Device Assembly is a replacement part for Specific refrigerator models. It is a kit that includes the start relay and overload, both of which are crucial components for the proper operation of the compressor. The start relay is responsible for initiating the compressor's operation by providing an electrical boost to start the motor. The overload, on the other hand, acts as a protective device. It monitors the current flow and protects the compressor from overheating or electrical overload. Replaces Part Numbers WR07X10097, 1265640, AH1766101, EA1766101, PD00008007, EAP1766101, AP4300623, PS1766101. Compatibility This replacement compressor overload relay fits select GE, Hotpoint, and Kenmore refrigerators. Example compatible models include (but are not limited to):GE GTS18HGTHWW, GTS22KGNRWWHotpoint HSS25GFTSAKenmore 363.9557710 Always verify your refrigerator’s model number before ordering.Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement – Designed to match OEM electrical protection performance 🔌 Compressor Safety Protection – Prevents overheating and electrical overload damage 🔇 Reduces Clicking Issues – Helps resolve start-up clicking or compressor cycling 💰 Cost-Effective Solution – Reliable alternative to OEM parts 🛡️ Fixes Common Issues – Solves compressor not starting, intermittent cooling, or shutdowns 📐 Product Specification Part Number: WR07X10097 Component Type: Refrigerator Compressor Overload Relay Material: Heat-resistant housing with internal thermal protection Mounting: Direct-fit on compressor terminals Function: Overcurrent and overheat protection Compliance: Built to OEM-equivalent quality standards (not OEM) 🛠️ Installation Notes Tools Needed: Phillips screwdriver, needle-nose pliers ⚠️ Safety First: Unplug the refrigerator before servicing. Compressor components may be hot—allow time to cool. Steps: Disconnect power and remove the rear lower access panel. Locate the overload relay attached to the compressor terminals. Carefully disconnect the old relay. Install the new XPARTCO WR07X10097 overload relay securely. Reinstall the access panel and restore power. Allow several minutes for compressor startup. ⏱️ Time Required: 10–15 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Appliance Parts Supplier 🔄 30-Day Return Policy Protect your refrigerator compressor and restore reliable cooling — Add to Cart Now for a dependable, budget-friendly repair!

Read more less

XPARTCO W10006355 Washer Shift Actuator  Fits specific Maytag, Kenmore, Whirlpool top-load machine models. Replaces Part Numbers: WPW10006355, W10006355, AP6014711, PS11747977. Description: This Shift Actuator is a replacement part for specific Maytag, Kenmore, Whirlpool washing machine models. It is an electronic component located inside the transmission that controls the shifting between wash cycles. The shift actuator receives signals from the washer control board to change modes, initiating proper movements to advance the cycle.   This is an aftermarket part that can be used as a replacement for the OEM part.

Read more less