XPARTCO DC97-16350U Washer Suspension Rod Kit (Set of 4)
The XPARTCO DC97-16350U is an aftermarket replacement washer suspension rod kit (set of 4) compatible with a wide range of Samsung top-load washers in the WA40, WA41, WA42, WA44, WA45, WA49, and WA50 series. The suspension rods are spring-loaded shock-absorbing rods that connect the outer washer tub to the top corners of the cabinet frame, suspending the tub and dampening the vibrations generated during agitation and high-speed spin cycles. When one or more rods lose tension, break, or degrade, the tub swings off-center and strikes the cabinet walls — causing violent shaking, loud banging, error code dc (out of balance), UE imbalance errors, and progressive damage to the machine.
Each rod measures 26.4–26.5 inches in overall length and 1-1/4 inches in diameter, constructed from spring steel with plastic end caps. The kit includes all 4 suspension rods — always replace all four at the same time since they wear at the same rate. It directly replaces DC97-16350S, DC97-16350T, DC97-16350E, DC97-16350C, DC97-16350D, DC97-16350K, DC97-05280W, 4962798, AP6884450, EAP12720841, PS12720841, and PD00065434. Wear gloves during installation — the rods are coated with grease. Installs in 20–30 minutes — no special tools required.
Quick Answer
The XPARTCO DC97-16350U Washer Suspension Rod Kit fixes Samsung top-load washers that vibrate violently, bang loudly, walk across the floor, or display dc or UE imbalance error codes during spin. Set of 4 rods, 26.4–26.5" long, 1-1/4" diameter, spring steel with plastic end caps. Replace all 4 at the same time. Wear gloves — rods are greased. Compatible with Samsung WA40–WA50 series. Replaces DC97-16350S, DC97-16350T, DC97-16350E, DC97-16350C, DC97-16350D, AP6884450, PS12720841.
Common Problems This Kit Fixes
Washer vibrating violently or shaking excessively during the spin cycle
Loud banging or thumping — tub striking the cabinet walls during spin
Washer "walking" or moving across the floor during high-speed spin
Error code dc displayed — Samsung out-of-balance error during spin
Error code UE displayed — unbalanced load error the washer cannot self-correct
Washer repeatedly stopping and rebalancing the load without completing the spin cycle
Visible broken, detached, or sagging suspension rod inside the washer cabinet
Rattling or clunking during agitation — tub no longer centered
Replaces Part Numbers
This suspension rod kit directly replaces the following OEM and cross-reference part numbers:
DC97-16350U, DC97-16350S, DC97-16350T, DC97-16350E, DC97-16350C, DC97-16350D, DC97-16350J, DC97-16350K, DC97-16350U, DC97-16350E, DC97-16350S, DC97-16350C, DC97-16350D, DC97-16350T, AP6884450, ASM34747, EAP12720841, PD00065434, PS12720841.
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This suspension rod kit is compatible with select top-load washers from the following Samsung series:
Samsung WA40 series — WA400PJHDWR, WA40J3000AW, WA40A3005AW, WA44A3205AW and related models
Samsung WA41 series — WA41A3000AW and related models
Samsung WA42 series — WA422PRHDWR and related models
Samsung WA45 series — WA45H7000AW, WA45H7200AW, WA45K7600AW, WA45M7050AW, WA45N3050AW, WA45T3200AW, WA45T3400AW, WA45T3400AP, WA456DRHDSU, WA456DRHDWR and related models
Samsung WA49 series — WA49B5105AW, WA49B5205AW and related models
Samsung WA50 series — WA50R5200AW, WA50R5400AV, WA50R5400AW, WA50T5300AC and related models
Kenmore / Sears top-load washers (select Samsung-built models)
Important: The DC97-16350U rod is 26.4–26.5 inches long and is for Samsung WA40–WA50 series washers. Larger-capacity WA48–WA54 series models use the longer DC97-16350V rod (27.5 inches). Always measure your existing rods or verify your model number before ordering — using the wrong length rod can cause the tub to sit at the incorrect height inside the cabinet.
Key Features
Set of 4 suspension rods — complete replacement covering all four tub mounting points
Suspends and centers the outer tub within the cabinet — dampens agitation and spin vibration to prevent tub-to-cabinet contact
Resolves Samsung error codes dc (out of balance) and UE (unbalanced load)
Rod length: 26.4–26.5 inches overall; diameter: 1-1/4 inches
Spring steel construction with plastic end caps — durable and corrosion resistant
Rods are pre-coated with grease — wear work gloves during installation
Replace all 4 rods at the same time — rods wear together and partial replacement results in uneven tub support
No special tools required — installs in 20–30 minutes
Replaces DC97-16350S, DC97-16350T, DC97-16350E, DC97-16350C, DC97-16350D, and over 15 additional cross-references
Aftermarket replacement built to OEM-equivalent quality standards
Product Specifications
Part Number
DC97-16350U
Part Type
Washer Suspension Rod and Spring Assembly
Condition
Aftermarket Replacement
Application
Samsung Top-Load Washers — WA40, WA41, WA42, WA44, WA45, WA49, WA50 series
Quantity
Set of 4 (replace all four rods at the same time)
Rod Length
26.4–26.5 inches overall
Rod Diameter
1-1/4 inches
Material
Spring steel / Plastic end caps
Color
Brass / Black / White / Pink
Lubrication
Pre-coated with grease — wear gloves during installation
Error Codes Resolved
dc (out of balance), UE (unbalanced load)
Compatible Brands
Samsung, Kenmore (Samsung-built)
Installation Notes
⚠️ Unplug Washer and Shut Off Water Before Starting — Wear Gloves Disconnect power and turn off the water supply before beginning. Wear work gloves throughout — the suspension rods are coated with grease. Remove the lid and the top panel (typically secured by screws under the lid hinge covers and at the rear corners). With the top panel removed, the four suspension rods are visible at the corners, each running from a mounting point on the tub rim up to a hook or bracket at the top corners of the cabinet frame. Note the orientation and attachment method of each rod before removing. Unhook the top of each rod from the cabinet bracket and lift the bottom cup off the tub mounting pin. Install each new DC97-16350U rod by seating the bottom cup onto the tub mounting pin and hooking the top over the cabinet bracket. Replace all four rods before reassembling. Reinstall the top panel and lid, restore power and water, and run a spin cycle to verify smooth, quiet, centered operation. Tools needed: Phillips screwdriver; no special tools required for the rods themselves.
Frequently Asked Questions
What is the difference between DC97-16350U and DC97-16350V?
Both are Samsung top-load washer suspension rods, but they are different lengths for different washer capacity generations. The DC97-16350U is approximately 26.4–26.5 inches long and is used on mid-capacity Samsung WA40 through WA50 series washers. The DC97-16350V is approximately 27.5 inches long and is used on larger-capacity WA48 through WA54 series washers. Using the wrong length rod causes the tub to sit at the wrong height inside the cabinet, which can cause new imbalance issues. Always measure your existing rods or verify your model number before ordering.
Why must I replace all 4 rods instead of just the broken one?
All four suspension rods experience the same amount of wear over the same number of wash cycles. When one rod fails, the remaining three have experienced the same stress and fatigue and are likely to fail soon after. Replacing only the broken rod leaves three worn rods supporting the tub unevenly — this can cause continued vibration, accelerate wear on the new rod, and require a second repair shortly after. Replacing all four at the same time ensures even tub support, fully resolves the imbalance, and prevents a repeat repair.
Do DC97-16350S, DC97-16350T, and DC97-16350E all cross to the DC97-16350U?
Yes — DC97-16350S, DC97-16350T, DC97-16350E, DC97-16350C, and DC97-16350D are all cross-reference part numbers for the same Samsung suspension rod assembly used across different production runs of the same washer series. Samsung updates part number suffixes during production revisions. All of these numbers have the same 26.4–26.5" length and are interchangeable with the DC97-16350U.
What do error codes dc and UE mean on Samsung washers?
Error code dc on Samsung top-load washers indicates the machine has detected an out-of-balance condition and stopped spinning to prevent damage. Error code UE indicates an unbalanced load that the washer cannot self-correct by redistributing. Both codes can be caused by an overloaded or unevenly distributed laundry load — but if the errors occur consistently even with normal, balanced loads, worn or broken suspension rods are the most common mechanical cause. Replacing the rod kit resolves these errors in most cases.
Is this an OEM or aftermarket part?
This is an aftermarket replacement kit built to OEM-equivalent quality standards. It is not a genuine Samsung OEM part, but is manufactured from spring steel with plastic end caps to match the length and spring tension of the original DC97-16350U suspension rods.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout
XPARTCO WH01X24378 Washer / Dryer Cycle Selector Knob
The XPARTCO WH01X24378 is an aftermarket replacement cycle selector knob (options knob) compatible with a wide range of GE, Hotpoint, RCA, Haier, Monogram, and Café washers and dryers. The selector knob is one of the primary user controls on the appliance's control panel — it's what you grip and turn to choose the wash or dry options and settings for each load. On many GE-platform washers and dryers, this smaller selector knob works alongside a larger main timer/cycle knob to give you fine-grained control over the specific options within your selected cycle. Over time, selector knobs wear out from repeated twisting motions, get cracked or dropped, or lose their grip on the internal shaft — all of which make it difficult or impossible to change the appliance's settings.
Constructed from heat-resistant plastic with a clean white and chrome finish. Snap-on installation — no tools required. Pulls straight off the control shaft and pushes back on. This knob directly replaces WH01X24378, AP5986397, 4396548, and PS11726904. Important: this is the smaller cycle selector/options knob. If you need the larger main timer knob for your GE washer, that's a different part number (PS11736611) — check which knob is broken before ordering. Installs in under 1 minute — no tools required.
Quick Answer
The XPARTCO WH01X24378 Washer Cycle Selector Knob replaces a cracked, loose, stripped, or missing selector knob on GE, Hotpoint, RCA, Haier, Monogram, and Café washers and dryers. Heat-resistant plastic, white and chrome finish. Snap-on installation — pulls straight off, pushes back on. Replaces AP5986397, 4396548, PS11726904. This is the smaller cycle/options knob — NOT the larger main timer knob (PS11736611). No tools required.
Common Problems This Part Fixes
Selector knob cracked, broken, or split from age and repeated use
Knob loose and slipping on the control shaft — no longer changes settings when turned
Knob has stripped or damaged internal grip and won't stay coupled to the shaft
Knob missing entirely from the control panel
Knob damaged from impact — dropped or bumped
Knob discolored, faded, or worn from years of daily handling
Difficulty selecting cycle options — knob no longer clicks into detent positions cleanly
Water or detergent damage to the knob material
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This cycle selector knob directly replaces the following OEM and cross-reference part numbers:
WH01X24378, 4396548, AGE26094, AP5986397, EAP11726904, OEM17959200, PD00037085, PS11726904.
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This selector knob is compatible with select washers and dryers from the following brands:
GE washers — GTW500ASNWS and related top-load models
GE dryers — GTX42GASJWW, GTD45GASJ2WS and related models
GE Profile and GE Café washers and dryers (select models)
GE Monogram washers and dryers (select models)
Hotpoint washers and dryers (select models)
RCA washers and dryers (select GE-built models)
Haier washers and dryers (select models using GE-platform controls)
Important — Two Knobs, Two Part Numbers: Many GE washers and dryers have TWO knobs on the control panel: a larger main timer/cycle knob and a smaller cycle selector/options knob. The WH01X24378 is the smaller cycle selector/options knob. If your broken knob is the larger main timer knob, you need a different part number (PS11736611 on many GE models). Before ordering, visually confirm which knob is broken and compare the size and shape to the images. Contact our support team with your model number if you're unsure.
Key Features
Cycle selector/options knob — used to choose specific settings within your selected wash or dry cycle
Snap-on installation — pulls straight off the control shaft, pushes straight back on; no tools or hardware required
Heat-resistant plastic construction — designed for years of daily use without warping or cracking
Clean white and chrome finish complements GE appliance styling
Ergonomic shape for comfortable grip and precise cycle selection
Restores full cycle control when the original knob has cracked, stripped, or gone missing
Replaces WH01X24378, AP5986397, 4396548, and PS11726904
Compatible with GE, Hotpoint, RCA, Haier, Monogram, and Café washers and dryers
Important: this is the smaller cycle selector/options knob — NOT the larger main timer knob (PS11736611, sold separately)
Aftermarket replacement built to OEM-equivalent quality standards
Quick replacement — installs in under 1 minute
Product Specifications
Part Number
XPWH01X24378
Part Type
Washer/Dryer Cycle Selector Knob (Options Knob)
Condition
Aftermarket Replacement
Application
Washers and Dryers (GE platform)
Knob Size
Smaller cycle/options knob (NOT the larger main timer knob)
Color
White / Chrome
Material
Heat-resistant plastic
Installation
Snap-on — no tools required
Larger Timer Knob
Different part — PS11736611 (sold separately)
Compatible Brands
GE, Hotpoint, RCA, Haier, Monogram, Café
Installation Notes
⚠️ Unplug Washer/Dryer Before Starting — Quick Toolless Replacement Disconnect power before beginning as a general safety precaution. Wear work gloves if desired. Locate the old cycle selector knob on the control panel of your washer or dryer. Grip the knob firmly and pull it straight off the control shaft — it should come off with a moderate pull (no tools or hardware required). If the knob is stuck or the internal grip has stripped and it's spinning without releasing, use a soft cloth wrapped around it for better grip, or gently pry it off with a plastic tool (avoid metal tools that could damage the control panel finish). Once the old knob is off, inspect the metal or plastic control shaft — if it's damaged, worn round, or spinning freely with no resistance, the underlying switch or shaft may also need replacement. If the shaft is intact, align the new WH01X24378 knob with the flat sides of the shaft (the knob has a matching D-shape or flat receiver inside) and push it firmly into place until it seats fully. Rotate the knob through its full range of positions to confirm it clicks into detents cleanly and turns smoothly. Restore power and run a test cycle. Tools needed: None (soft cloth optional).
Frequently Asked Questions
Is this the smaller or larger knob on my GE washer?
The WH01X24378 is the smaller cycle selector (options) knob. Many GE washers and dryers have two knobs on the control panel: a larger main timer/cycle knob that selects the primary wash program, and a smaller cycle options knob (this one) that selects sub-options like temperature, spin speed, or soil level. Before ordering, look at your control panel and identify which knob has failed — if the smaller knob is broken, this is the correct part. If the larger main timer knob is broken, you need a different part (PS11736611 on many GE models). The two knobs are not interchangeable.
How do I remove the old knob if it's cracked or spinning without coming off?
If the internal grip on the old knob has stripped and it's spinning freely on the shaft without releasing, wrap a soft cloth around it for extra grip and pull firmly straight up. If that still doesn't work, gently pry it off with a plastic pry tool (a plastic putty knife or credit card can work). Avoid metal tools that could scratch the control panel finish. If the knob is cracked, you can sometimes break away the broken pieces to expose the internal grip on the shaft, then work each piece off. Once the old knob is off, inspect the control shaft — if it's damaged or spinning without resistance, the underlying switch may need replacement too.
Do I really not need any tools for this?
Correct — the WH01X24378 uses a snap-on installation with no screws or hardware. To install, align the new knob with the flat side (D-shape) of the control shaft and push it straight down until it seats fully. The whole replacement typically takes under a minute. Just make sure the knob is fully seated and rotates through all positions with the correct detent clicks before you plug the appliance back in.
The knob installs fine but my washer still doesn't change settings — what next?
If the new knob is installed correctly (fully seated and rotates through positions with detent clicks) but changing the knob position doesn't change the cycle behavior, the underlying selector switch or control shaft has likely failed — not the knob. Common causes include the shaft spinning freely without engaging the switch inside (the shaft has stripped or broken), or the electrical selector switch itself has failed. In these cases, replacing just the knob won't fix the problem — the switch assembly behind the panel also needs to be replaced. Contact our support team with your model number for the correct switch part number.
Is this an OEM or aftermarket part?
This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine GE OEM part, but is manufactured from heat-resistant plastic to match the dimensions, D-shape shaft receiver, snap-on installation, and cycle selection function of the original WH01X24378 selector knob used in compatible GE, Hotpoint, RCA, Haier, Monogram, and Café washers and dryers.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout
XPARTCO W10276397 Washer Drain Pump Replaces WPW10276397
The XPARTCO W10276397 is an aftermarket replacement washer drain pump and motor assembly compatible with a wide range of Whirlpool-family top-load washers including Whirlpool Cabrio, Maytag Centennial, Amana, Kenmore, Roper, Crosley, and Inglis. The drain pump removes water from the washer tub during the drain portion of each wash cycle. When the pump fails, the washer will not drain, will leave standing water in the tub, display error code F9E1, stop mid-cycle, or produce unusual humming or grinding noises during the drain phase.
This complete drain pump and motor assembly uses a Hanyu B40-3A motor (also marked 91PS3132) and includes the integrated impeller — the impeller is not sold separately. It directly replaces WPW10276397, W10276397, WPW10276397VP, 1874334, B40-3A, LP397, AP6018417, PS11751719, and several additional cross-reference numbers. Before ordering, confirm that the drain hose and any coin trap or filter are clear — a blocked hose or clogged filter can mimic pump failure symptoms. Installs in 20–30 minutes with basic hand tools.
Quick Answer
The XPARTCO W10276397 Washer Drain Pump fixes Whirlpool Cabrio and Maytag Centennial top-load washers that won't drain, leave standing water, display error code F9E1, or make humming/grinding noises during the drain cycle. Complete pump and motor assembly with integrated impeller. Motor: Hanyu B40-3A / 91PS3132. Replaces WPW10276397, 1874334, B40-3A, LP397, AP6018417, PS11751719. Compatible with Whirlpool Cabrio, Maytag Centennial/MVWC/MVWX, Amana, Kenmore, Roper, Crosley, and Inglis top-load washers.
Common Problems This Part Fixes
Washer not draining — standing water remaining in the tub after a cycle
Error code F9E1 displayed — drain pump fault or slow drain detected
Washer stopping mid-cycle due to a drain fault
Loud humming during the drain phase — motor running but impeller not pumping
Grinding or rattling noise during drain — physical damage to impeller or pump housing
Water draining very slowly — worn pump motor below rated flow
Water leaking from the drain pump area
Replaces Part Numbers
This drain pump directly replaces the following OEM and cross-reference part numbers:
WPW10276397, W10276397, 1874334, AP6018417, AWP50231 EAP11751719 FIX11751719, OEM24073670, PD00003595, PS11751719, WPW10276397VP
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This drain pump is compatible with select top-load washers from the following brands and series:
Whirlpool top-load washers — Cabrio series (WTW4800, WTW4810, WTW4850, WTW4900, WTW5000, WTW5200, WTW5300, WTW5500, WTW5600, WTW5640, WTW5700 and related models)
Maytag top-load washers — Centennial series (MVWC200, MVWC215, MVWC300, MVWC400, MVWC415, MVWC416, MVWC425, MVWC465 and related models)
Maytag top-load washers — MVWX series (MVWX500, MVWX550, MVWX600, MVWX700 and related models)
Amana top-load washers (ATW, NTW series and related models)
Kenmore / Sears top-load washers — 110 series (Whirlpool-built Cabrio-platform models)
Roper top-load washers (RTW series)
Crosley top-load washers (CAE series)
Inglis top-load washers (select models)
Note: This pump is for top-load washers only. Always verify your exact model number before ordering. Check and clear the drain hose and any coin trap before replacing the pump — a blocked hose can produce the same symptoms as a failed pump.
Key Features
Removes water from the tub during the drain and spin cycles for proper washer operation
Complete pump and motor assembly — includes integrated impeller (impeller not sold separately)
Motor: Hanyu B40-3A / 91PS3132 — matched to original pump specifications
Resolves error code F9E1 (drain pump fault / slow drain) on compatible Whirlpool and Maytag top-load washers
Replaces WPW10276397, W10276397, 1874334, B40-3A, LP397, and AP6018417
Compatible with Whirlpool Cabrio, Maytag Centennial/MVWX, Amana, Kenmore, Roper, Crosley, and Inglis top-load washers
Aftermarket replacement built to OEM-equivalent quality standards
DIY repair — installs in 20–30 minutes with basic hand tools
Product Specifications
Part Number
W10276397
OEM Part Number
WPW10276397
Part Type
Washer Drain Pump and Motor Assembly
Condition
Aftermarket Replacement
Application
Top-Load Washers (Cabrio, Centennial, and related platforms)
Motor
Hanyu B40-3A / 91PS3132
Includes
Pump motor and integrated impeller assembly
Error Code Resolved
F9E1 (drain pump fault / slow drain)
Compatible Brands
Whirlpool, Maytag, Amana, Kenmore, Roper, Crosley, Inglis
Installation Notes
⚠️ Unplug Washer and Shut Off Water Before Starting Disconnect power and turn off the water supply before beginning. Place towels and a shallow pan near the pump access area to catch residual water. The drain pump is located beneath the washer tub on Cabrio and Centennial models — access it by removing the front lower panel or by tilting the washer back and working from underneath. Disconnect the drain hose clamp and hose from the pump, then disconnect the wire harness connector. Unscrew the pump mounting screws and remove the old pump. Before installing the new pump, verify the drain hose and any coin trap or filter are completely clear of debris — a blocked hose or trap will cause the new pump to fail again. Install the new W10276397 pump in the same position, reconnect the hose and wire harness, and secure the mounting screws. Restore power and water and run a drain or spin cycle to confirm drainage and check for leaks. Tools needed: Phillips screwdriver, pliers, shallow pan, towels.
Frequently Asked Questions
What does error code F9E1 mean on Whirlpool Cabrio and Maytag Centennial washers?
F9E1 indicates a drain fault — the washer was unable to drain within the expected time during the cycle. It can be caused by a clogged drain hose, a blocked coin trap or filter, a kinked drain hose, or a failed drain pump motor. Always check and clear the drain hose and filter before replacing the pump — a blockage is often the cause and clearing it resolves the error without needing a new pump. If the hose and filter are clear and the error persists, the pump motor has likely failed.
What is the difference between W10276397 and WPW10276397?
These are the same drain pump assembly. WPW10276397 is the updated Whirlpool OEM part number that superseded the original W10276397. The 1874334 and B40-3A are also cross-references for this same pump. This aftermarket replacement is compatible with all of these numbers.
My washer hums but won't drain — is it the pump?
A humming sound during the drain cycle without water being expelled usually means the pump motor is receiving power and running, but the impeller is not turning — either because it is jammed with debris or because the impeller shaft has broken. First check for and remove any foreign objects (coins, lint, small clothing items) from the pump area. If the impeller is clear and the pump still hums without draining, the motor or impeller is mechanically failed and the pump assembly needs replacement.
Does this pump fit the Whirlpool Cabrio and Maytag Bravos washers?
The W10276397 is compatible with Whirlpool Cabrio and Maytag Centennial top-load washers on the VM transmission platform. Maytag Bravos XL and Bravos X models may also be compatible depending on the specific model number — verify your exact model before ordering. Contact our support team if you need confirmation for a specific Bravos model.
Is this an OEM or aftermarket part?
This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured with a Hanyu B40-3A motor to match the specifications and performance of the original WPW10276397 drain pump assembly.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout
WH23X27419 Washer Genuine OEM Drain Pump – Compatible with GE, Haier & Hotpoint Washers
Product Description
Restore proper draining and reliable washer performance with the WH23X27419 Washer Genuine OEM Drain Pump. This original equipment manufacturer (OEM) drain pump is engineered by the manufacturer to exact specifications, ensuring proper water removal during drain and spin cycles. A failing drain pump can cause standing water, slow draining, loud noises, or error codes. Replacing it with this genuine OEM pump helps return your washer to factory-level performance and reliability.
This part is a Genuine OEM component, designed for exact fit, correct electrical ratings, and long-term durability.
Replaces Part Numbers
WH23X27419, WD-5470-09, 4588221, PD00053097, EAP12343437, AP6328341, PS12343437.
Compatibility
This Genuine OEM washer drain pump fits select GE and Hotpoint top-load washers.
Example compatible models include (but are not limited to):
GE GTW465ASNWW, GTW485ASJWS
Hotpoint HTW240ASKWS
Haier HLP24E, RWT350AW, GWT450AW, XQB6091AF, Xqb60-91Af, HLP28E, GWT480BW
Always verify your washer’s model number before ordering.Contact our support team if you’re unsure.
✅ Key Features
🏭 Genuine OEM Part – Manufactured to original factory specifications
💧 Efficient Water Removal – Restores proper draining and spin performance
🔇 Quiet Operation – Reduces grinding or humming noises
💪 OEM-Grade Motor & Housing – Built for long service life
🔧 Exact Fit & Plug-and-Play Installation – No modifications required
📐 Product Specification
Part Number: WH23X27419
Component Type: Washer Drain Pump
Voltage: 120V AC
Mounting: Direct-fit, bolt-on installation
Application: Washer drain and spin system
OEM Status: Genuine OEM
🛠️ Installation Notes
Tools Needed: Phillips screwdriver, nut driver, pliers
⚠️ Safety First: Unplug the washer and shut off the water supply before servicing.
Basic Steps:
Disconnect washer power and water supply.
Access the drain pump from the bottom or rear of the washer.
Remove hoses and electrical connectors.
Remove mounting screws and take out the old pump.
Install the new WH23X27419 Genuine OEM drain pump.
Reconnect hoses and wiring, reassemble panels, and restore power.
Run a test cycle to confirm proper draining.
⏱️ Time Required: 25–35 minutes
📦 Shop With Confidence
🏭 Genuine OEM Appliance Part
🚚 Free Shipping on All Orders
🔄 30-Day Return Policy
Restore factory-level washer performance and reliable draining — Add to Cart Now with confidence!
W11688994 Washer Genuine OEM Water Valve
Single water inlet valve, hot
Replaces Part Numbers: W11688994, W11316255, W11036928, W11486360, AP7218602, PS17216729.
Description: This Water Inlet Valve is a Genuine OEM part for specific Maytag, Kenmore, Whirlpool washing machine models. It controls the flow of water into the washer tub at designated stages in the washing process. Water enters through the valve inlet and is distributed to internal components like the detergent dispenser, water pipes, and sump hoses. Common causes of a bad valve can include mineral scale buildup inhibiting proper flow regulation over time, or cracks and leaks from wear and tear on rubber gaskets and seals.
XPARTCO DC97-20621C Washer Drain Pump Assembly
The XPARTCO DC97-20621C is an aftermarket replacement drain pump assembly compatible with a wide range of Samsung front-load washers in the specific series, as well as select Kenmore front-load washers built on the Samsung platform. The drain pump removes water from the washer tub during the drain portion of each wash cycle. When the pump fails, the washer will not drain, leave standing water in the tub, stop mid-cycle, display error codes 5C, SE, nd, 5E, or 4E, or make loud grinding or humming noises during the drain phase.
The DC97-20621C is the current production revision of this pump, which also covers the earlier DC97-20621A variants — all three are the same pump in successive production runs. It also replaces DC97-17999N, DC31-00187A, PX3516-01, AP6807020, 4959632, PS12592830, and EAP12592830. Before ordering, always check the drain filter/coin trap at the bottom front of the washer — a clogged filter is a common cause of drain error codes that does not require pump replacement. Installs in 20–30 minutes with basic hand tools.
Quick Answer
The XPARTCO DC97-20621C Washer Drain Pump Assembly fixes Samsung front-load washers displaying error codes 5C, SE, nd, 5E, or 4E, not draining, leaving standing water, or making loud grinding or humming noises during the drain cycle. Covers DC97-20621A and DC97-20621B variants. Compatible with select Samsung series and Kenmore (Samsung-built). Replaces DC97-20621A, DC97-17999N, DC31-00187A, PX3516-01, AP6807020, 4959632, PS12592830, EAP12592830. Check drain filter before replacing pump.
Common Problems This Part Fixes
Washer not draining — standing water remaining in the tub after a cycle
Error codes 5C, SE, nd, 5E, or 4E displayed — drain fault detected
Washer stopping mid-cycle due to a drain fault
Loud humming during the drain phase — pump motor running but not pumping
Grinding or rattling noise during drain — damaged impeller or worn pump bearings
Water draining very slowly — worn pump below rated performance
Clothes excessively wet after a cycle — pump not fully removing water before spin
Water leaking from the pump area at the front bottom of the washer
Replaces Part Numbers
This drain pump directly replaces the following OEM and cross-reference part numbers:
DC97-20621C, DC97-17999N, DC97-20621A, 03DC31-00187A, AP7366238, ASM105564, PFIX17701443, PD00095227, PX3516-01, PS17701443, AP6807020, PS12592830.
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This drain pump is compatible with select Samsung front-load washers and related Kenmore models:
Samsung series — WF50R8500AW, WF45T6200AW, WF53BB8900 and related models
Kenmore / Sears front-load washers (select Samsung-built models)
Important: Before replacing the pump, check and clean the drain filter/coin trap located behind the lower access panel at the front of the washer. A clogged filter causes the same error codes as a failed pump and is the most common fixable cause of Samsung front-load drain errors. Always verify your model number before ordering.
Key Features
Removes water from the tub during drain and spin cycles for proper washer operation
Resolves Samsung error codes 5C, SE, nd, 5E, and 4E caused by drain pump failure
DC97-20621C is the current production revision — covers DC97-20621A and DC97-20621B as well
Also replaces DC97-17999N, DC31-00187A, PX3516-01, AP6807020, 4959632, PS12592830, and EAP12592830
Compatible with select Samsung series and Kenmore Samsung-built front-load washers
Aftermarket replacement built to OEM-equivalent quality standards
DIY repair — installs in 20–30 minutes with basic hand tools
Product Specifications
Part Number
XPDC97-20621C
Also Covers
DC97-20621A (prior revisions)
Part Type
Front-Load Washer Drain Pump Assembly
Condition
Aftermarket Replacement
Application
Samsung Front-Load Washers
Error Codes Resolved
5C, SE, nd, 5E, 4E
Compatible Brands
Samsung, Kenmore (Samsung-built)
Installation Notes
⚠️ Unplug Washer and Shut Off Water Before Starting Disconnect power and turn off the water supply before beginning. Place towels on the floor in front of the washer — residual water will drain when the pump is disconnected. The drain pump is accessed through the lower front panel. Remove the lower kick panel screws to expose the drain filter and pump area. First, drain residual water by removing the drain filter cap (have a shallow pan ready — up to a quart of water may flow out). After draining, disconnect the pump wiring harness. Release the hose clamps and disconnect the drain hoses from the pump. Unscrew or unclip the pump mounting hardware and remove the old pump. Install the new DC97-20621C pump in the same position, reconnect drain hoses and secure clamps, reconnect the wiring harness, and reinstall the front panel. Restore power and water and run a drain/spin cycle to confirm drainage and check for leaks. Tools needed: Phillips screwdriver, pliers, shallow pan, towels.
Frequently Asked Questions
What is the difference between DC97-20621C and DC97-20621A?
These are successive production revisions of the same Samsung front-load washer drain pump assembly. DC97-20621A was the original version, DC97-20621B was an intermediate revision, and DC97-20621C is the current production part. All three are the same pump with minor manufacturing changes across production runs — they are fully interchangeable. If your washer's parts diagram or old pump label shows any of these numbers, this replacement covers all of them.
What error codes indicate a drain pump failure on Samsung front-load washers?
Error codes 5C, SE, nd, 5E, and 4E on Samsung front-load washers all indicate a drain fault — the washer was unable to drain within the expected time. Before replacing the pump, clean the drain filter/coin trap at the front lower access panel — lint, coins, and debris in the filter are among the most common causes of these error codes. If the filter is clean and the errors persist, the pump itself has failed and needs replacement.
Where is the drain filter on my Samsung front-load washer?
The drain filter (also called the coin trap) on Samsung front-load washers is located behind the lower front access panel, typically on the right side. Remove the lower kick panel by pressing the release tab or removing the screws. You will see a small cap or twist-out cover — that is the filter. Place a shallow pan under it and slowly unscrew the cap to allow water to drain out. Remove any debris from the filter, then replace the cap and reinstall the panel. Run a cycle to check if the error clears. If the filter was clogged, this may be all the repair needed.
My washer makes a loud noise during draining — is it the pump?
A loud humming or grinding during the drain cycle is a common sign of a failing pump. Humming without water movement means the motor is running but the impeller is not pumping — either jammed by debris or mechanically failed. Grinding suggests worn pump bearings or a damaged impeller. Check the drain filter first for foreign objects. If the filter is clear and the noise persists, the pump needs replacement.
Is this an OEM or aftermarket part?
This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Samsung OEM part, but is manufactured to match the specifications and performance of the original DC97-20621C drain pump assembly.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout
XPARTCO 137221600 Washer Drain Pump
The XPARTCO 137221600 is an aftermarket replacement washer drain pump compatible with a wide range of Frigidaire, Electrolux, Crosley, Gibson, Kelvinator, Kenmore, Tappan, and Westinghouse front-load washers — including popular Affinity series and washer-dryer combo models. The drain pump is mounted at the base of the washer and is responsible for evacuating the wash and rinse water from the tub through the drain hose at the end of each cycle. When the drain pump fails, the washer can't drain — leaving clothes soaking wet, water pooling in the tub, and the wash cycle unable to advance to spin. Common failure symptoms include humming without pumping (blocked or seized impeller), leaks from the pump housing, loud grinding or clicking noises, and complete pump silence when a drain cycle should be running.
Rated 120V AC, 60Hz, 85W, 1.25A. Based on the Askol M65 design, with a firmly attached red flapper to prevent drain backflow into the tub. Constructed from strong, durable plastic to resist cracking and leaking through many years of cycling. Package includes the drain pump, mounting base, and mounting screw. This part directly replaces 137108100, 137151800, 137151800KITK, 131724000, 134051200, 134740500, 134740800, 2754548, ER137108100, TJ137108100, EAP7783938, LP1600, BPX401-72J, AP5684706, and PS7783938. Important: before installing the new pump, clean any lint or debris from the rubber boot, verify the drain hose is clear and properly fastened, and check the pump filter for blockage — installing a new pump on a system with the underlying blockage will not resolve the drainage problem. Installs in 30–60 minutes with basic hand tools.
Quick Answer
The XPARTCO 137221600 Washer Drain Pump fixes Frigidaire, Electrolux, Crosley, Gibson, Kelvinator, Kenmore, Tappan, and Westinghouse front-load washers that won't drain, leave clothes soaking wet, are noisy or humming during the drain cycle, or display an E11 error code. 120V AC, 60Hz, 85W, 1.25A. Askol M65 design with red backflow flapper. Kit includes pump + mounting base + screw. Replaces 137108100, 137151800, 137151800KITK, 131724000, 134051200, 134740500, 134740800, 2754548, ER137108100, TJ137108100, EAP7783938, LP1600, BPX401-72J, AP5684706, PS7783938.
Common Problems This Part Fixes
Washer not draining — pump failed to remove water at the end of the wash or rinse cycle
Clothes left soaking wet at the end of the cycle — no drain, so no spin can start
Water leaking from the bottom of the washer — cracked pump housing or failed seal
Loud humming noise but no water flowing — pump motor running against a seized impeller or blockage
Grinding, clicking, or unusual noises during the drain cycle
E11 error code displayed on the control panel (drain fault)
Washer pumps but won't spin — drain cycle can't complete, blocking spin
Cycles taking much longer than normal as the washer tries to drain
Pump silent during drain — motor windings open or electrical fault
Impeller broken, cracked, or missing pieces after opening the pump
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This drain pump directly replaces the following OEM and cross-reference part numbers:
137221600, 131724000, 134051200, 134740500, 137108100, 137151800, 137151800KITK, 2754548, TJ137108100, ER137108100, PD00000118, EAP7783938, BPX401-72J, AFR14249, AP5684706, PS7783938, Also replaces GE WH23X10041, 2119312, WH23X10009, WH23X10017, WH23X10031, WH23X10034, AH3502779, EA3502779, AP5324214, PS3502779.
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This drain pump is compatible with select front-load washers and washer-dryer combos from the following brands:
Frigidaire front-load washers — Affinity series (FAFW3001LW3, FAFW3801LW3 and related), FEX831FS2/FS4, FTF2140ES1, FWS445RFS2, FWX445RFS3 series
Frigidaire front-load washers — ATF6000ES1, ATF8000FS1, ATFB6700FS0 series
Frigidaire front-load washers — GLTF2940ES3, GLTF2940FS1 and related GLTF series
Frigidaire washer-dryer combos — CWS3600AS1 and related
Electrolux front-load washers — select models
Crosley front-load washers — select models
Gibson front-load washers — select models
Kelvinator front-load washers — select models
Kenmore / Sears front-load washers — select Frigidaire-built models (41744052400, 41744052401, 41744052500, 41744082500, 41748102700, 41748106700, 41748116700, 41790812995 and related 417-series)
Tappan front-load washers — select models
Westinghouse front-load washers — select models
Note: The redesigned 137221600 may look slightly different from your original (e.g., white or gray housing vs. original black), but functions identically. Ensure proper orientation and flapper alignment during installation. Always verify your appliance model number before ordering.
Key Features
Aftermarket replacement built to OEM-equivalent quality standards
Drain pump — removes water from the washer tub through the drain hose at the end of the wash and rinse cycles
Resolves "won't drain," "won't spin," "wet clothes," "E11 error," and "humming pump" symptoms
120V AC, 60Hz, 85W, 1.25A — correct electrical specifications for compatible Frigidaire-platform washers
Askol M65 design with red backflow flapper to prevent water from flowing back into the tub
Strong, durable plastic construction resistant to cracking and leaking
Kit includes: 1x drain pump, 1x mounting base, 1x mounting screw
Replaces 15+ OEM and cross-reference part numbers including 137108100, 137151800, 131724000, 134051200, 134740500, 134740800, AP5684706, and PS7783938
Compatible with Frigidaire (Affinity, FEX, FTF, FWS, FWX, ATF, ATFB, GLTF, CWS series), Electrolux, Crosley, Gibson, Kelvinator, Kenmore (417-series), Tappan, and Westinghouse front-load washers and washer-dryer combos
DIY repair — installs in 30–60 minutes with basic hand tools
Product Specifications
Part Number
XP137221600
Part Type
Washer Drain Pump
Condition
Aftermarket Replacement
Application
Front-Load Washers and Washer-Dryer Combos (Frigidaire/Electrolux platform)
Voltage
120V AC
Frequency
60 Hz
Wattage
85W
Amperage
1.25A
Design
Askol M65 with red backflow flapper
Material
Durable plastic
Includes
1x Drain Pump, 1x Mounting Base, 1x Mounting Screw
Error Codes Resolved
E11 (drain fault)
Compatible Brands
Frigidaire, Electrolux, Crosley, Gibson, Kelvinator, Kenmore, Tappan, Westinghouse
Installation Notes
⚠️ Unplug Washer and Shut Off Water Before Starting — Wear Work Gloves — Check for Blockage First Disconnect power at the outlet or breaker and shut off both water supplies at the wall before beginning. Wear work gloves to protect your hands — pump components can have sharp edges. Have towels ready — residual water remains in the pump housing and hoses. Important: before replacing the pump, check for the underlying cause of the drain problem. Inspect the pump filter (accessible on many models via the lower front kick panel), the drain hose for kinks, and the rubber boot at the bottom of the tub for lint, coins, buttons, or other debris — installing a new pump on a system with an unresolved blockage will not fix the drain problem. Remove the appropriate access panel (typically the rear or front lower kick panel — model-dependent) to expose the pump. Photograph the wire harness and hose connections before disconnecting. Disconnect the electrical wire connectors from the pump motor. Squeeze the hose clamps with pliers and slide them back to release the tub-to-pump hose and the pump-to-drain-hose from the pump. Remove the 2 mounting screws holding the pump to its base and lift the old pump out. Clean any residual debris from the rubber boot, hoses, and pump filter area. Install the new 137221600 pump using the included mounting base and screw. Reconnect the hoses with the clamps, orient the red backflow flapper correctly, and reconnect the electrical connectors. Reinstall the access panel, restore water and power, and run a rinse cycle to test drainage and check for leaks at all connections. Tools needed: Phillips screwdriver, needle-nose pliers, channel-lock pliers, small flathead screwdriver, towel, work gloves.
Frequently Asked Questions
My washer won't drain — is it always the pump?
Not always. Before replacing the pump, check for these common causes: 1) Clogged pump filter — most Frigidaire front-load washers have a filter accessible via the lower front kick panel; coins, buttons, lint, and small items can block it. 2) Kinked or clogged drain hose — inspect the entire drain hose from the pump to the wall standpipe or sink. 3) Blocked rubber boot — small items can get stuck between the tub and the pump inlet. 4) Failed lid lock/door switch — if the washer doesn't detect a locked door, it won't run the drain cycle. If all of these check out and the pump still isn't draining (or is humming without moving water), the pump has failed and this is the correct repair.
What is the E11 error code on my Frigidaire washer?
E11 on Frigidaire and Electrolux front-load washers indicates a drain fault — the control board is not detecting successful drainage within the expected time. Common causes are a failed drain pump, a clogged pump filter, a kinked or clogged drain hose, or debris blocking the impeller. If you've verified the filter and hose are clear but the code persists, replacing the 137221600 drain pump typically resolves it. If the code returns after replacement, check the wire harness between the pump and the control board.
Does the pump come with everything I need for installation?
Yes — the 137221600 (OE) package includes the drain pump itself, a mounting base, and a mounting screw. This is everything you need for the pump replacement itself. However, you should reuse the original hose clamps and hoses from your old pump (they should still be in good condition). If you find that the rubber boot at the base of the tub is cracked, hardened, or torn during the repair, that's a separate part that would need to be ordered — inspect it before completing the reinstallation.
The new pump looks different from my old one — is it the right part?
Very likely, yes. The 137221600 has been through several revisions over its production history — some housings are black, others white or gray, and the exact shape can vary slightly across production runs. As long as the mounting bolt pattern, hose inlet/outlet sizes, and electrical connector are the same, and the specs match (120V, 60Hz, 85W, Askol M65 design), the pump will function identically to your original. During installation, focus on correct orientation and flapper alignment — the flapper (red) must be positioned so it opens outward toward the drain hose direction to prevent backflow.
Is this an OEM or aftermarket part?
This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Frigidaire/Electrolux OEM part, but is manufactured to match the electrical specifications (120V AC, 60Hz, 85W, 1.25A), Askol M65 design, red backflow flapper, dimensions, and drain pump function of the original 137221600 used in compatible Frigidaire, Electrolux, Crosley, Gibson, Kelvinator, Kenmore, Tappan, and Westinghouse front-load washers.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
AHA75673401 Washer Genuine Drain Pump
Fits Specific LG Washer models
Description: This Washing Machine Drain Pump is an OEM part for specific LG washing machine models. It is responsible for effectively draining water out of the washing machine after each cycle. The pump works to remove water from the tub and drain hoses, preparing the machine for the next load.
Replaces Part Numbers: AHA75673401, 4873470, AP6335290, PS12580277.
California Residents only
WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov
Genuine OEM WPW10140917 Washer Water Inlet Valve with Vacuum Break
The Genuine OEM Whirlpool WPW10140917 is the water inlet valve with vacuum break for select Whirlpool-built washers, including Maytag, Kenmore, Amana, Inglis and other brands. The valve regulates water intake for wash cycles and delivers water into the washer drum, and the vacuum break helps keep wash water from backing up into the supply. When the valve fails, the washer may leak, and fill problems can follow.
This is the original Whirlpool part, not an aftermarket equivalent. Check your model number before ordering.
Quick Answer
The Genuine OEM WPW10140917 Water Inlet Valve replaces the water inlet valve on a compatible Whirlpool-built washer when it leaks or no longer controls water intake correctly. Replaces W10140917. Classic symptom: water leaking at the valve.
Common Problems This Part Fixes
Water leaking at the inlet valve
Water inlet valve not controlling water intake correctly
Washer not filling or filling incorrectly because of a failed valve
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This water inlet valve replaces or supersedes the following part numbers:
WPW10140917, W10140917, OEM18047055, AP6015682, AWP49689, EAP11748963, PD00003949, PS11748963
Whirlpool sells similar valves under nearby numbers, such as WPW10140918, which are not interchangeable by number alone. If your old valve shows a different number, contact our support team and we'll check whether it matches.
Compatibility
This water inlet valve is listed for Whirlpool, Maytag, Kenmore, KitchenAid, Amana, Inglis, Jenn-Air, Magic Chef and Crosley washers, including these examples:
WTW5100VQ1, WTW5100VQ2, WTW5300SQ2, 1CWTW5100VQ1
CAWS9234VQ0, ETW4400VQ3, NTW4500VQ1
ITW4300SQ3, IV45001, IV4500X0
Note: The models above are a small sample, not a full list. Check your full model number against your parts diagram, or contact our support team to verify fit before ordering.
Key Features
Genuine OEM Whirlpool part, not an aftermarket equivalent
Water inlet valve with vacuum break
Regulates water intake and delivers water into the washer drum
Sold as one complete valve
Product Specifications
Part Number
WPW10140917
OEM Part Number
WPW10140917
Part Type
Washer Water Inlet Valve with Vacuum Break
Condition
Genuine OEM
Manufacturer
Whirlpool
Application
Select Whirlpool-Built Washers
Installation Notes
⚠️ Unplug Power And Shut Off Water Before Installing Unplug the washer and turn off the water supply before you begin, and wear protective gloves. Access to the valve is typically through the back panel or the control panel, depending on the model. Note where each hose and wiring connector goes, disconnect them, remove the old valve, and fit the new valve in the same position. Reconnect everything, restore water and power, and run a short cycle while checking for leaks.
Frequently Asked Questions
My washer is leaking at the valve. Is this the part I need?
If the leak is coming from the water inlet valve itself, replacing the valve is the repair. Check the supply hoses and their connections first, since a loose or worn hose can leak in the same area.
Is this an OEM or aftermarket part?
This is a genuine OEM part from Whirlpool, not an aftermarket equivalent.
Can I use a valve with a similar part number?
Not by number alone. Whirlpool sells several water inlet valves with similar numbers for different washers. Match the part number and your model number, or contact our support team and we'll check for you.
Will this fit my washer?
It is listed for many Whirlpool-built washers, but the model list above is only a sample. Check your full model number against your parts diagram, or contact our support team and we'll verify it before you order.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping ✓ Genuine OEM Parts ✓ Compatibility Support ✓ Secure Checkout
XPARTCO 280187 Washer Drain Pump Assembly
The XPARTCO 280187 is an aftermarket replacement drain pump assembly for Whirlpool-built front-load washers sold under the Whirlpool, Kenmore, Kenmore Elite, Maytag, KitchenAid, and Amana names. The drain pump pushes water out of the tub through the drain hose at the end of the wash and rinse stages. When it clogs, wears out, or seizes, the washer can stop with water still in the drum, throw drain errors, stop before the spin cycle, leak, or make loud humming or grinding noises.
This is a complete drain pump assembly, including the pump motor and housing, so it replaces the whole unit rather than just an internal part. The pump sits at the base of the washer behind the lower front panel, and the swap typically takes 15–30 minutes with common hand tools.
Quick Answer
The XPARTCO 280187 Drain Pump Assembly fixes a Whirlpool-built front-load washer that won't drain, leaves water in the drum, stops before spinning, leaks from the pump, or makes loud noise during draining. Complete pump motor and housing, aftermarket replacement. Classic symptom: the cycle stalls with water still in the tub, or you hear a loud hum or grind while it tries to drain.
Common Problems This Part Fixes
Washer won't drain, or water is left in the drum after the cycle
Drain error codes or the cycle stopping before the spin
Loud humming, grinding, or rattling while the washer drains
Water leaking from the pump or its housing
Pump motor seized or not running
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This drain pump assembly replaces the following part numbers:
280187, 1200164, 285998, 8181684, 8182819, 8182821, AH1485610, AP3953640, AWP39453, EA1485610, EAP1485610, PD00002352, PS1485610
These are Whirlpool's current and earlier numbers for this pump. If your old pump or parts diagram shows any of them, this is the matching replacement.
Compatibility
This pump is listed for select front-load washers from:
Whirlpool, including Duet models such as WFW9400VE03, WFW9500TW03, and WFW9600TW02
Kenmore and Kenmore Elite, including 11042822200, 11042926200, 11045962400, and 11045966403
Maytag, including MHWE400WR00 and MHWE400WW0
KitchenAid, including KHWS02RWH0
Amana
Note: The model list above is only a sample, since this pump fits many more models. Confirm fit by matching the number on your old pump or parts diagram against the Replaces list, or contact our support team with your model number and we'll verify before you order. This pump is for front-load washers and is not intended for top-load machines.
Key Features
Aftermarket replacement drain pump assembly
Complete unit with pump motor and housing
Restores full draining so cycles finish and the washer can spin
Cross-references to Whirlpool 280187, 285998, 8181684, 8182819, and 8182821
Fits select Whirlpool, Kenmore, Maytag, KitchenAid, and Amana front-load washers
Typical installation 15–30 minutes with common hand tools
Product Specifications
Part Number
XP280187
OEM Part Number
280187
Part Type
Washer Drain Pump Assembly
Condition
Aftermarket Replacement
Included
Pump Motor and Housing
Application
Select Whirlpool, Kenmore, Kenmore Elite, Maytag, KitchenAid & Amana Front-Load Washers
Installation Notes
⚠️ Unplug Power and Expect Water Unplug the washer and turn off the water supply before starting. Remove the lower front panel to reach the pump at the base of the washer, then drain any residual water into a shallow pan or with a wet/dry vacuum, using the drain hose or the small drain cap if your model has one. Disconnect the wiring harness from the pump, then loosen the clamps holding the hoses and pull the hoses off. Remove the pump's mounting screw and take out the old pump. Fit the new pump in the same position, reattach the hoses with the clamps (replace worn clamps if needed), and reconnect the wiring harness. Check that the pump and hose connections are secure, replace the front panel, restore power and water, and run a drain cycle while checking for leaks. Common tools include a nutdriver or Torx driver, screwdrivers, and pliers.
Frequently Asked Questions
My washer won't drain. Is this the part I need?
A failed or clogged drain pump is one of the most common causes. Before replacing it, check the drain hose and the pump filter for a clog, such as a sock or coin. If the filter is clear but the pump hums, grinds, or doesn't run, replacing the pump should fix it.
Does this include the pump motor?
Yes. This is the complete assembly, with the pump motor and housing.
My old pump is marked 285998, 8181684, 8182819, or 8182821. Will this work?
Yes. All of those are earlier Whirlpool numbers for this pump, and 280187 is the current number.
Will this fit my top-load washer?
It is intended for front-load washers. Contact our support team with your model number if you're unsure, and we'll confirm before you order.
Is this an OEM part?
No. This is an XPARTCO aftermarket replacement built to match the Whirlpool 280187. If you prefer a genuine OEM pump, contact us.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout
WB24X25013 Genuine OEM GE Range Surface Burner Infinite Switch Replaces WB24X47186.
The WB24X25013 is a genuine GE OEM infinite control switch for a dual (bridge) surface element on GE, Hotpoint, and select Kenmore electric ranges — the kind of burner with an inner coil and an outer coil that can be run together for a large pot or as the inner coil alone for a small pan. Because it's governing two coil zones instead of one, this switch uses six terminal connections rather than the three or four found on a standard single-element infinite switch, and it mounts to the control panel with a distinctive figure-8 style shaft and two female mounting holes.
Like any infinite switch, it doesn't have fixed heat positions — instead it rapidly cycles power to the element(s) on and off at a ratio set by the knob, giving continuous heat adjustment from warm to high rather than a handful of steps. Rated for 240VAC at 15 amps. Over years of cycling, the internal contacts on a switch like this wear, pit, or weld together, and boilovers or spills can corrode the switch body and cause it to fail. A worn switch on a dual-element burner can produce an unusually wide symptom set: the whole burner may fail, or just the outer ring may stop responding while the inner coil still works, or the burner may stay on continuously regardless of the knob position. It directly replaces WB24X47186, 191D4774P005, AP5999509, PS11729102, EAP11729102, and 4464832. As a genuine OEM part, the WB24X25013 is manufactured by GE to factory specifications — guaranteed fit, materials, and performance.
Quick Answer
The WB24X25013 Genuine OEM GE Range Surface Burner Infinite Switch fixes GE, Hotpoint, and Kenmore electric ranges with a dual (bridge) element burner where the burner won't turn on or off, only the outer ring fails to work while the inner coil still heats, the burner stays on continuously, or heat can't be adjusted. Six-terminal switch, figure-8 shaft, 240VAC / 15A. Replaces WB24X47186, 191D4774P005, AP5999509, PS11729102, EAP11729102, 4464832. Not the same switch as a standard single-element infinite switch — this one is specific to dual/bridge burners with an inner and outer coil.
Common Problems This Part Fixes
Dual-element burner won't turn on at all when the knob is turned
Outer ring of a dual/bridge element won't activate while the inner coil still works
Burner won't turn off — stays hot even with the knob at the off position
Burner stuck at one heat level regardless of where the knob is set
No ability to adjust temperature — always full blast or always low
Intermittent burner operation — works sometimes, not others
Knob feels loose, gritty, or doesn't turn smoothly through its range
Burner failure that followed a boilover or liquid spill on the control panel
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This range surface burner infinite switch directly replaces the following OEM and cross-reference part numbers:
WB24X25013, WB24X47186, 191D4774P005, AGE1543754, AP7216136, PS11729102, PS17872685, EAP11729102, 4464832, 191D4774P005, MDSA-W767-GEM
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This dual-element infinite switch is compatible with select GE, Hotpoint, and Kenmore electric ranges equipped with a dual (bridge) surface element, including model families such as:
GE JB6, JB7, and JB8 series electric ranges (including JB630, JB640, JB645, and JB655)
GE JBS series electric ranges
GE JS6 and JS7 series electric ranges (including the JS760 series)
GE GRS and GRF series electric ranges
Hotpoint electric ranges (select GE-built models)
Select Kenmore electric ranges built on the GE platform
Verified model numbers include: JB645RK6SS, JS760EP6ES, JS760DP6WW, JS760SP7SS, JS760DP7WW, JS760SP6SS, JS760FP7DS, JS760FP6DS, JS760EP7ES, JB860EJAES, JB860FJADS, and GRS500PV1SS.
Note: This is a six-terminal switch built specifically for a dual (bridge) element with a figure-8 style shaft and two female mounting holes — it is NOT interchangeable with a standard single-element infinite switch such as the WB24T10029 or WB24T10025, which use fewer terminals and a different shaft profile. Fitting a standard single-element switch to a dual-element burner circuit will not correctly control both coil zones. Always verify your full model number and confirm the affected burner is a dual/bridge element before ordering. Contact our support team with your model number if you're unsure.
Key Features
Genuine GE OEM part — factory-specified contact design for dual-element switching
Six-terminal design controls both the inner coil and outer ring of a dual (bridge) surface element
Figure-8 style shaft with two female mounting holes matched to the original control panel bracket
Infinite switch design allows continuous heat adjustment rather than a handful of fixed positions
Rated 240VAC at 15 amps
Resolves "burner won't turn on," "outer ring not working," "won't turn off," and "stuck at one heat level" symptoms caused by worn or corroded switch contacts
Direct drop-in replacement — mounts to the same control panel bracket and wiring harness
Replaces 191D4774P005, AP5999509, PS11729102, EAP11729102, and 4464832
Genuine OEM replacement — guaranteed fit, materials, and performance
Product Specifications
Part Number
WB24X25013
Part Type
Range Surface Burner Infinite Switch (Dual/Bridge Element)
Condition
Genuine OEM
Brand
GE
Element Type Controlled
Dual (bridge) surface element — inner coil + outer ring
Terminal Connections
6
Shaft Style
Figure-8
Mounting
Two female mounting holes
Voltage
240VAC
Amperage
15A
Function
Cycles element power to allow continuous (infinite) heat adjustment across both coil zones
Quantity
1 switch
Compatible Brands
GE, Hotpoint, select Kenmore
Installation Notes
⚠️ 240V Circuit — Unplug Range Or Shut Off Breaker Before Starting Disconnect power at the outlet or shut off the circuit breaker before beginning — this switch operates on a 240V circuit, and working on it while powered presents a serious shock hazard. Wear work gloves. Remove the burner knob (it typically pulls straight off, though some models use a small retaining clip) then remove the screws securing the control panel or backsplash to reach the switch from behind. Photograph the wiring before disconnecting anything — this is a six-terminal switch, and getting even one wire out of place can miswire the inner coil, the outer ring, or both. Label each wire as you remove it. Disconnect all six terminal connections from the old switch, then remove the mounting screws from the two mounting holes and pull the switch free from its figure-8 shaft opening. Install the new WB24X25013 in the same orientation, reconnect each of the six wires exactly as labeled, and secure the mounting hardware. Reinstall the control panel or backsplash, press the knob back onto the shaft, restore power, and test the burner at every knob position — confirm the inner coil and outer ring both activate correctly (together and, if your model supports it, with the outer ring switched off independently) before considering the repair complete. Tools needed: Phillips screwdriver, nut driver, wire terminal pliers (helpful but optional), work gloves.
Frequently Asked Questions
How do I know if my burner uses a dual-element switch like this one?
Look at the burner element itself: a dual (bridge) element has two distinct coil rings — a smaller inner coil and a larger outer ring — usually with a separate control or a knob position that lets you activate just the inner coil for a small pan or both rings together for a large pot. A standard single-ring element has only one coil and uses a simpler switch with fewer terminals. If your range has this two-ring burner design, the WB24X25013 (or the exact switch behind it) is the correct type — but always confirm your model number, since dual-element switches vary by range generation.
Only the outer ring of my dual burner doesn't work. Is it the switch or the element?
It could be either, and it's worth narrowing down before ordering. If the inner coil heats normally but the outer ring never activates at any knob position, check the outer ring element itself first — a broken element coil is a common and cheaper fix than a switch. If the outer ring element tests fine but the switch's six-terminal wiring specific to the outer coil circuit has failed or corroded, the infinite switch is the correct replacement.
Can I use a standard single-element infinite switch instead if this one is out of stock?
No. A standard single-element switch has fewer terminals and cannot correctly control the two separate coil zones of a dual (bridge) burner. Wiring a single-element switch into a dual-element circuit will leave one coil zone permanently uncontrolled or non-functional. Always order the six-terminal dual-element switch specified for your model.
What does "infinite switch" mean?
An infinite switch lets you dial in a continuous range of heat rather than a few fixed positions, by rapidly cycling the element's power on and off at a ratio set by the knob — low settings get short power pulses, high settings get long ones. When the internal contacts wear or weld together from years of cycling, the switch can get stuck feeding constant power (burner always hot) or stop switching at all (burner always off), regardless of where the knob is turned.
A spill got into the control panel and now the burner won't turn off. Is that the switch?
Very likely, yes. Liquid boilovers and spills are one of the most common causes of infinite switch failure — moisture gets into the switch body, corrodes or bridges the internal contacts, and the switch can end up stuck feeding power continuously even with the knob turned to off. If you suspect this, shut off power to the range immediately at the breaker rather than relying on the knob, since a shorted switch may not respond to it at all.
Is this an OEM or aftermarket part?
This is a genuine OEM part, manufactured by GE to factory specifications — guaranteed fit, materials, and performance. It matches the original six-terminal wiring, figure-8 shaft, 240VAC/15A electrical rating, and dual-coil switching behavior of the infinite switch originally installed for the dual (bridge) element in your GE, Hotpoint, or Kenmore range.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
WH13X10024 Genuine OEM Washer Water Valve
Replaces Part Numbers: WH13X10024, WH13X0086, WH13X0087, WH13X10004, WH13X10019, WH13X86, WH13X87, AH1155105, EA1155105, OEM15444478, AP3861119, PS1155105.
Description: This Water Inlet Valve is a Genuine OEM part for select GE washing machine models. This component is crucial for controlling the flow of water into the washer during the wash and rinse cycles. It works by opening and closing the solenoids to allow the appropriate amount of hot or cold water to enter the washing machine, based on the selected settings.
California Residents only
WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov
