XPARTCO W11688995 Washer Water Inlet Valve (Cold)
The XPARTCO W11688995 is an aftermarket replacement cold water inlet valve designed as a direct fit for select Whirlpool, Maytag, Amana, KitchenAid, Jenn-Air, Magic Chef, Admiral, Norge, Roper, Inglis, and Kenmore front-load washers. The cold water inlet valve is mounted at the back of the washer where the cold water supply hose connects. When the washer's control board calls for cold water during a wash cycle, the valve's internal solenoid opens, letting water flow into the tub or detergent dispenser. The valve closes the instant the control board cuts power, stopping flow precisely as the correct fill level is reached.
When this valve fails, the washer may not fill with cold water at all, fill very slowly, fail to dispense fabric softener, continuously drip water into the tub even when off, or display F8E1 or LO FL error codes. Construction is blue and white plastic with metal solenoid coil, ~3"H x 4"W x 3"L, with 1/2" NPT threaded inlet for standard washer supply hose. It directly replaces W11688995, W11036930, W11316256, W11486361, AP7218603, EAP12711564, PD00086086, PS12711564, 4929298, and AP6835737. Often replaced as a pair with the hot water inlet valve (W11688994, sold separately). Installs in 10–15 minutes with basic hand tools.
Quick Answer
The XPARTCO W11688995 Washer Water Inlet Valve (Cold) fixes Whirlpool, Maytag, Amana, KitchenAid, Jenn-Air, and Kenmore front-load washers displaying F8E1 or LO FL error codes, not filling with cold water, filling slowly, failing to dispense fabric softener, or continuously dripping into the tub. Blue/white plastic with metal coil, 1/2" NPT thread, ~3"H x 4"W x 3"L. Replaces W11036930, W11316256, W11486361, AP7218603, EAP12711564, PD00086086, PS12711564, 4929298, AP6835737. Often paired with the hot water valve (W11688994, sold separately).
Common Problems This Part Fixes
Washer not filling with cold water — valve solenoid not opening when commanded
Washer filling slowly with cold water — valve partially clogged or weak solenoid
F8E1 error code displayed — cold water inlet valve fault
LO FL (low flow) error code — valve unable to deliver normal water flow
Fabric softener not being dispensed — cold water flush to dispenser failing
Water continuously dripping into the tub when the washer is off — valve stuck open or not fully closing
Water leaks at the valve body — internal seal failure
Wash cycles taking much longer than normal due to slow fill
Replaces Part Numbers
This cold water inlet valve directly replaces the following OEM and cross-reference part numbers:
W11688995, W11316256, W11036930, W11486361, 4983050, PD00086086, FIX17216730, EAP17216730, OEM28874414, AP7218603, AWP46809, PS17216730.
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This cold water inlet valve is compatible with select front-load washers from the following brands:
Whirlpool front-load washers — WFC6810LW0, WFC9820HC0, WFC9820HW0 series
Whirlpool front-load washers — WFW560CHW0, WFW560CHW1, WFW560CHW2, WFW560CHW3, WFW560CHW4 series
Whirlpool front-load washers — WFW5605MC0, WFW5605MW0 series
Whirlpool front-load washers — WFW5620HW0, WFW5620HW1, WFW5620HW2, WFW5620HW3 series
Whirlpool front-load washers — WFW6620HC0, WFW6620HC1, WFW6620HC2, WFW6620HW0, WFW6620HW1 series
Whirlpool front-load washers — WFW8620HC0, WFW8620HC1, WFW8620HC2, WFW8620HC3, WFW8620HC4, WFW8620HW0, WFW8620HW1, WFW8620HW2, WFW8620HW3, WFW8620HW4 series
Whirlpool front-load washers — WFW862CHC0, WFW862CHC1, WFW862CHC2, WFW862CHC3 series
Whirlpool front-load washers — WFW9620HBK1, WFW9620HBK2, WFW9620HBK3, WFW9620HC0, WFW9620HC1, WFW9620HC3, WFW9620HW0, WFW9620HW1, WFW9620HW2, WFW9620HW3 series
Maytag front-load washers — MHW5630HC0, MHW5630HW1, MHW5630MBK0 series and related
Amana front-load washers — NFW5800HW0, NFW5800HW1 and related models
Inglis front-load washers — IFW5900HW, IFW5900HW1 and related models
KitchenAid, Jenn-Air, Magic Chef, Admiral, Norge, Roper front-load washers — select Whirlpool-built models
Kenmore / Sears front-load washers — select Whirlpool-built models
Note: This is the cold water inlet valve (typically blue). The matching hot water inlet valve is part number W11688994 (typically red). When you replace one valve, it's a good practice to replace the other at the same time since they're the same age, both are accessible during the same repair, and the second valve will likely fail in the near term. Always verify your model number before ordering.
Key Features
Aftermarket replacement built to OEM-equivalent quality standards
Controls the flow of cold water into the washer during fill cycles
Solenoid-actuated — opens precisely when the control board calls for cold water and closes the moment the call is dropped
Resolves F8E1 and LO FL error codes when caused by a failed cold inlet valve
1/2" NPT threaded inlet for standard washer supply hose connection
Dimensions: approximately 3" H x 4" W x 3" L
Blue and white plastic body with metal solenoid coil — designed for long-term reliability against wash cycle pressure and temperature
Replaces W11036930, W11316256, W11486361, AP7218603, EAP12711564, PD00086086, PS12711564, 4929298, and AP6835737
Compatible with Whirlpool, Maytag, Amana, KitchenAid, Jenn-Air, Magic Chef, Admiral, Norge, Roper, Inglis, and Kenmore front-load washers
Often replaced together with the hot water inlet valve (W11688994, sold separately) as a paired repair
Quick DIY repair — installs in 10–15 minutes with basic hand tools
Product Specifications
Part Number
XPW11688995
Part Type
Washer Water Inlet Valve (Cold)
Condition
Aftermarket Replacement
Application
Front-Load Washers (Whirlpool platform)
Water Type
Cold (paired hot valve is W11688994)
Inlet Thread
1/2" NPT
Dimensions
Approximately 3" H x 4" W x 3" L
Color
Blue / White
Material
Plastic / Metal
Error Codes Resolved
F8E1, LO FL (when caused by cold valve fault)
Often Paired With
Hot Water Inlet Valve (W11688994, sold separately)
Compatible Brands
Whirlpool, Maytag, Amana, KitchenAid, Jenn-Air, Magic Chef, Admiral, Norge, Roper, Inglis, Kenmore
Installation Notes
⚠️ Unplug Washer and Shut Off Water Supply Before Starting — Wear Work Gloves Disconnect power and shut off both the hot and cold water supplies at the wall before beginning. Wear work gloves to protect your hands. Have towels ready — residual water remains in the supply hoses and will spill when disconnected. Pull the washer out from the wall to access the back. Remove the three 1/4" screws securing the rear edge of the top cover, push the top cover slightly back, and lift it off. Locate the inlet valves at the back of the washer — the cold valve is typically blue. Disconnect the cold water supply hose from the valve (water will drip — towels). Photograph the wire connections before disconnecting. Unplug the small electrical connector from the valve solenoid. Remove the single 3/16" mounting screw (or similar hardware, model-dependent) holding the valve in place, and disconnect any internal water hoses from the valve outlet (channel-lock pliers may help with hose clamps). Install the new W11688995 valve in the same position with the same orientation, reconnect the internal water hoses and electrical connector, and secure the mounting screw. Reconnect the cold supply hose at the wall, restore water and power, and run a test cycle to confirm normal cold water fill with no leaks. Tip: while the top cover is off, this is the ideal time to also replace the hot water valve (W11688994) — they share the same access and lifespan. Tools needed: 1/4" nut driver, 3/16" nut driver, adjustable wrench or pliers, work gloves.
Frequently Asked Questions
What do error codes F8E1 and LO FL mean on Whirlpool washers?
Both codes indicate a water fill problem. F8E1 appears when the control board doesn't detect normal water flow during a fill cycle — typically caused by a failed inlet valve, a clogged inlet screen, kinked supply hose, or restricted water supply. LO FL (low flow) appears when the washer detects that water is flowing in, but at a rate too low to complete the fill within the expected time window. When the cold water inlet valve has failed or is partially clogged, both codes can appear together. Before replacing the valve, check that the household cold water supply is on and the supply hose isn't kinked, and inspect the inlet screen on the valve for sediment buildup. If those check out, replacing the W11688995 typically resolves the codes.
My washer isn't dispensing fabric softener — could this be the cold valve?
Yes — this is actually a common symptom that's often misdiagnosed. The cold water inlet valve also feeds the detergent dispenser tray on most Whirlpool front-load washers, including the fabric softener compartment. If the cold valve is clogged or failing to fully open at the right moment in the cycle, water doesn't flow through the fabric softener compartment to flush it into the tub, leaving softener pooled in the tray at the end of the cycle. If you've already cleaned the dispenser tray and water lines and the problem persists, replacing the cold inlet valve (W11688995) often resolves the issue.
Should I replace the hot water valve at the same time?
Yes, it's strongly recommended. The cold and hot inlet valves are essentially identical components installed side by side at the back of the washer — they're the same age, are exposed to the same wash cycle stress, and have the same expected service life. When one fails, the other is typically not far behind. Since the top cover is already off and both valves are accessible during the same repair, replacing both saves you a second teardown later. The matching hot water valve is part number W11688994 (red, sold separately) and is also available as a paired kit.
My washer is dripping water into the tub even when it's off — is this the valve?
Yes, that's a classic sign of a failed inlet valve. When the solenoid wears out or debris keeps the valve from sealing fully closed, water leaks past it at low rates and drips into the tub even with the washer powered off — especially noticeable as a slow puddle forming over a day or two. Since both the hot and cold valves feed into the tub, you'll want to identify which one is leaking: shut off the hot water supply at the wall and check if dripping continues. If it stops, the hot valve is at fault; if it continues, this cold valve is the cause. Replacing the W11688995 will resolve a leaking cold valve.
Is this an OEM or aftermarket part?
This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured to match the dimensions, electrical specifications, 1/2" NPT thread, and solenoid function of the original W11688995 cold water inlet valve used in compatible Whirlpool, Maytag, Amana, KitchenAid, and Kenmore front-load washers.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout
DA34-00041B Refrigerator Door Switch – Replacement for Samsung
Product Overview
The DA34-00041B Refrigerator Door Switch is an aftermarket replacement that controls interior lighting and signals the control board when the refrigerator or freezer door is open or closed. A malfunctioning switch can result in the light staying off or on, cooling fans not running correctly, or even door-related error codes. Replacing a faulty switch with this part helps restore normal operation and energy efficiency.
Replaces Part Numbers
This part replaces DA34-00041B, DA34-10110B, AP5957961, PS10061325.
It is designed to meet OEM specifications for reliable fit and performance in Samsung-built refrigerators.
Compatible Brands
This door switch is compatible with refrigerators manufactured by Samsung and Kenmore (Samsung-built). It fits a wide range of French door, bottom freezer, and side-by-side models.
Fixes the Following Issues
Refrigerator light not turning on or off
Cooling fan not operating when door closes
Door-related error messages
Inconsistent temperature regulation
Why Buy from Parts‑O‑Matic
Affordable and reliable aftermarket solution
Fast and free U.S. shipping
Easy to install with no special tools required
Trusted by appliance repair professionals and DIYers
279570 Genuine OEM Whirlpool Dryer Door Catch Kit
The 279570 is a Genuine OEM Whirlpool dryer door catch and strike kit compatible with a wide range of Whirlpool, Kenmore, Roper, Estate, Amana, Crosley, Inglis, KitchenAid, Maytag, and Admiral dryers. The door catch is the spring-clip mechanism on the dryer door that snaps over the door strike to hold the door firmly closed during operation, activating the door switch so the dryer can run. When the catch breaks, wears out, or loses tension, the door will not stay closed, the door switch will not be activated, and the dryer will either not start or will stop mid-cycle. The strike is the corresponding post or tab on the dryer cabinet that the catch engages.
This Genuine OEM kit includes three color-coded door catches of different tensions and two metal door strikes, plus one screw. Because the tension of the catch must match the original, Whirlpool includes three options in the kit — each is color-coded and numbered on the back. Refer to identify which catch is correct for your model. The kit directly replaces a very large list of older cross-reference numbers including 279570VP, 3493, 2003, 8208, 279280, 279337, 696144, 693717, AP3094183, PS334230, and dozens more. Installs in under 15 minutes with a Phillips screwdriver.
Quick Answer
The 279570 Genuine OEM Whirlpool Dryer Door Catch Kit fixes dryers where the door won't stay closed, pops open mid-cycle, or won't activate the door switch to start. Kit includes 3 color-coded catches (different tensions), 2 metal strikes, 1 screw. Use the catch that matches your original. Genuine OEM. Compatible with Whirlpool, Kenmore, Roper, Estate, Amana, Crosley, Inglis, KitchenAid, Maytag, and Admiral dryers. Installs in under 15 minutes.
Common Problems This Kit Fixes
Dryer door will not stay closed during the drying cycle
Door pops open mid-cycle, stopping the dryer
Dryer will not start — door switch not being activated by a worn or broken catch
Door feels loose or does not click shut firmly when closed
Door catch visibly cracked, broken, or missing
Door strike bent or missing — door cannot engage the catch properly
Dryer requires the door to be held or pushed closed to stay running
Replaces Part Numbers
This door catch kit directly replaces the following OEM and cross-reference part numbers:
279570, 14205029, 14205577, 14210022, 2003, 236876, 236877, 241282, 241890, 26000279570, 261847, 263067, 279280, 279337, 279469, 279570VP, 291949, 3390239, 3392538, 3398175, 342295, 347813, 3493, 4165234, 51651001, 51655001, 66021, 690081, 690082, 693717, 694343, 696144, 8208, 830751, 834767, 834813, 834943, 834944, AH334230, DE902, EA334230, EAP334230, FSP279570, AP3094183, AWP39897, PD00002346, PS334230.
Contact our support team with your model number if you need confirmation before ordering.
Compatibility
This door catch kit is compatible with select dryers from the following brands:
Whirlpool dryers (gas and electric)
Kenmore / Sears dryers (Whirlpool-built models)
Roper dryers
Estate dryers
Amana dryers
Crosley dryers
Inglis dryers
KitchenAid dryers
Maytag dryers
Admiral dryers
Important: This kit includes three catches with different spring tensions, color-coded and numbered on the back. You must use the catch that matches the tension of your original. Using the wrong tension catch may result in a door that is too hard to open or too easy to pop open.
Key Features
Genuine OEM kit manufactured by Whirlpool to factory specifications — guaranteed fit and performance
Holds the dryer door closed and activates the door switch so the dryer can run safely
Kit includes 3 color-coded door catches (different spring tensions), 2 metal door strikes, 1 screw
Catches are color-coded and numbered on the back — use the one that matches your original.
Plastic catches with metal strikes and metal screw — durable construction for long service life
Consolidates a very large list of older Whirlpool-family door catch cross-reference numbers
Compatible with 10 major appliance brands on the Whirlpool platform
Quick DIY repair — installs in under 15 minutes with a Phillips screwdriver
Product Specifications
Part Number
279570
Part Type
Dryer Door Catch and Strike Kit
Condition
Genuine OEM
Application
Gas and Electric Dryers
Kit Includes
3 color-coded door catches (different tensions), 2 metal strikes, 1 screw
Material
Plastic catches / Metal strikes
Color
White / Silver
Catch Selection
Color-coded and numbered, Use the catch that matches your original
Compatible Brands
Whirlpool, Kenmore, Roper, Estate, Amana, Crosley, Inglis, KitchenAid, Maytag, Admiral
Installation Notes
⚠️ Unplug Dryer Before Starting Disconnect power before beginning. using the wrong tension catch will result in incorrect door resistance. Open the dryer door and locate the old door catch on the inside of the door panel and the strike on the dryer cabinet opening. To remove the old catch: press the retaining tabs and pull the catch free from its slot, or unscrew the mounting screw. Install the correct new catch into the same position. To replace the strike: remove the old strike (typically held by a single screw) and install the new strike in the same position. Close the dryer door to confirm it latches firmly with a satisfying click. Restore power and run a short test cycle to confirm the door stays closed and the dryer operates normally. Tools needed: Phillips screwdriver; needle-nose pliers may help with catch removal on some models.
Frequently Asked Questions
Why does the kit include three different catches?
Whirlpool used door catches with different spring tensions across its dryer lineup — a lighter catch on some models and a stiffer catch on others. To cover all compatible models in a single kit, Whirlpool includes three catches of different tensions, each color-coded and numbered on the back. It is important to use the correct one — using a catch with too little tension may allow the door to pop open, while a catch with too much tension may make the door difficult to open.
Do I need to replace both the catch and the strike, or just one?
It depends on which component has failed. The catch (the spring-clip on the door) is the more commonly replaced part — it wears out from repeated use faster than the strike. Inspect both: if the catch is cracked or has lost its spring tension, replace the catch. If the strike is bent, cracked, or missing, replace the strike. Since the kit includes both catches and strikes, you have everything needed for a complete repair. When in doubt, replacing both ensures the full latch system is renewed.
My dryer will not start even after replacing the door catch — what else could it be?
If the dryer still will not start after the catch is replaced, the door switch may also need to be tested. The door switch is the electrical component that the door catch activates when the door closes — if the switch itself is failed, replacing the catch alone will not restore function. Test the door switch (3406107 for most Whirlpool-family models) with a multimeter for continuity in both the open and closed positions. If the switch reads open in both positions or closed in both positions, it has failed and needs replacement.
How is the 279570 different from the W11429587 dryer door catch?
The 279570 is the door catch kit for older Whirlpool-family dryers — it includes multiple catches of different tensions and metal strikes because it covers a wide range of older models. The W11429587 is a single snap-in door catch for newer Whirlpool-family dryers (Cabrio and newer platform models). If your dryer is a newer model with a snap-in catch slot rather than a screw-mounted catch and strike, you likely need the W11429587. Verify your model number to confirm which part is correct.
Is this a Genuine OEM or aftermarket part?
This is a Genuine OEM kit manufactured by Whirlpool to factory specifications. It is the exact same door catch and strike kit supplied by Whirlpool for compatible dryer service repairs — guaranteed fit, materials, and performance.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
W11688995 Genuine OEM Whirlpool Washer Water Inlet Valve (Cold)
The W11688995 is a genuine Whirlpool OEM cold water inlet valve for Whirlpool-built front-load washers. Whirlpool's newer front-load platforms use two separate single-function valves instead of one combined hot/cold valve body — this cold-side valve handles only the cold water supply, while a matching hot-side valve (sold separately as W11688994) handles the hot side. When the control calls for a cold fill, it energizes this valve's solenoid coils to open the water path; when the correct level is reached, the valve closes again. If this valve fails to open, the washer won't take on cold water; if it fails to seal fully closed, water can trickle into the drum even when the washer isn't running.
Because this is a dedicated single-function valve, a failure here shows up in a very specific way: cold-only fills stop working or slow down dramatically, while hot-only fills (governed by the separate W11688994 valve) continue working normally. Whirlpool's own service guidance links this valve to F8 E1 and LO FL fill-related error codes. Common failure modes include mineral or sediment buildup that prevents the valve from sealing, a burned-out solenoid coil, or a worn internal diaphragm. It directly replaces W11036930, W11316256, W11486361, AP7218603, PS17216730, and EAP17216730. As a genuine OEM part, the W11688995 is manufactured by Whirlpool to factory specifications — guaranteed fit, materials, and performance.
Quick Answer
The W11688995 Genuine OEM Whirlpool Washer Water Inlet Valve (Cold) fixes Whirlpool-built front-load washers where cold water won't fill, fills slowly, overfills, leaks into the drum when off, or throws an F8 E1 or LO FL error code. 120V, 50/60Hz, two-coil cold-only valve, 1/2" NPT threaded connections. Replaces W11036930, W11316256, W11486361, AP7218603, PS17216730, EAP17216730. This is the cold-side valve only — the companion hot-side valve is sold separately as W11688994.
Common Problems This Part Fixes
Washer won't fill with cold water while hot water fills normally
Cold water fills much more slowly than it used to
Washer overfills or takes on more water than the cycle calls for
Water trickling or leaking into the drum on the cold side when the washer is off
F8 E1 or LO FL error code displayed on the control panel
Cycle stalling at the fill step and never advancing to wash
Cold-wash or cold-rinse cycles specifically affected while warm/hot cycles run fine
Water pooling underneath or behind the washer near the cold supply connection
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This washer cold water inlet valve directly replaces the following OEM and cross-reference part numbers:
W11688995, W11316256, W11036930, W11486361, 4983050, PD00086086, FIX17216730, EAP17216730, OEM28874414, AP7218603, AWP46809, PS17216730.
W11486361 and W11316256 were earlier Whirlpool numbers for this same valve, with W11036930 preceding those. If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This cold water inlet valve is compatible with select Whirlpool-built front-load washers across the Whirlpool family of brands, including:
Whirlpool front-load washers — WFW series
Maytag front-load washers — MHW and MFW series (select Whirlpool-built models)
Amana front-load washers (select models)
Inglis front-load washers — IFW series (select models)
Select Kenmore front-load washers built on the Whirlpool platform
Verified model numbers include: 8TWFC6810LW0 (laundry center), IFW5900HW0, IFW5900HW1, IFW5900HW2, IFW5900HW3, IFW5900HW4, MFW7020RF0, MFW7020RU0, MFW7020RW0, MHW5630HC0, MHW5630HC1, MHW5630HC2, MHW5630HC3, MHW5630HW0, MHW5630HW1, MHW5630HW2, MHW5630MBK0, MHW6630HC0 through MHW6630HC3, MHW6630HW0 through MHW6630HW3, MHW6630MBK0, MHW8630HC0 through MHW8630HC3, MHW8630HW0 through MHW8630HW3, WFW560CHW0, WFW560CHW1, WFW560CHW2, WFW5620HW0 through WFW5620HW3, WFW6620HC0 through WFW6620HC2, WFW6620HW0, WFW6620HW1, WFW8620HC0 through WFW8620HC4, WFW8620HW0 through WFW8620HW4, WFW862CHC0, and WFW862CHC1.
Note — cold side only: This is the cold water valve. The matching hot water valve for these same washers is sold separately under part number W11688994. The two are not interchangeable — each is a dedicated single-function valve, and installing this cold valve in place of the hot valve (or vice versa) will not correctly control water temperature. If both valves need replacement, order both part numbers. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure.
Key Features
Genuine Whirlpool OEM part — factory-specified solenoid, seal, and flow-rate design
Dedicated cold-only water inlet valve — two internal coils control flow to the cold supply
Resolves "won't fill with cold water," "fills slowly," "overfills," and "leaking into the drum" symptoms caused by valve failure
Commonly resolves F8 E1 and LO FL error codes
1/2" NPT threaded connections for standard supply line hookups
Direct drop-in replacement for W11036930, W11316256, and W11486361
Replaces W11036930, W11316256, W11486361, AP7218603, PS17216730, and EAP17216730
Compatible with Whirlpool, Maytag, Amana, Inglis, and select Kenmore front-load washers
Genuine OEM replacement — guaranteed fit, materials, and performance
Product Specifications
Part Number
W11688995
Part Type
Washer Water Inlet Valve — Cold
Condition
Genuine OEM
Brand
Whirlpool
Application
Front-Load Washers (Whirlpool-Built)
Voltage
120V
Frequency
50/60 Hz
Coils
2 (dedicated cold water function)
Connection
1/2 in. NPT threaded
Companion Part
W11688994 (hot water valve, sold separately)
Supersedes
W11036930, W11316256, W11486361
Quantity
1 valve
Compatible Brands
Whirlpool, Maytag, Amana, Inglis, select Kenmore
Installation Notes
⚠️ Shut Off Water Supply And Unplug Washer Before Starting — Have A Towel Ready Unplug the washer or shut off its circuit breaker, and shut off both the hot and cold water supply valves before beginning. Wear work gloves. Disconnect the cold water supply line from the back of the valve first — have a towel or shallow pan ready, since residual water will spill out. Remove the rear screws securing the top panel, then slide the panel back and lift it off to access the valve assembly from inside the cabinet. Photograph the wiring connections before disconnecting anything, since the hot and cold valves sit side by side and it's easy to cross a wire. Disconnect the electrical connector from the old cold valve, remove its mounting screw or bracket, and pull the valve free — leave the hot valve (W11688994) undisturbed if it isn't also being replaced. Install the new W11688995 in the same position, secure the mounting screw, and reconnect the electrical connector fully. Reattach the cold water supply line, tightening securely by hand plus a partial turn with pliers — avoid overtightening plastic threaded fittings. Reinstall the top panel, restore the water supply, and check the connection for leaks before restoring power. Run a short cycle set to a cold wash and confirm the tub fills at the normal rate with no leaking underneath or behind the washer. Tools needed: 1/4" nut driver or socket, T-20 Torx bit, pliers, towel or shallow pan, work gloves.
Frequently Asked Questions
Cold water won't fill but hot water works fine. Is this the right part?
Yes — that's exactly the symptom pattern this valve addresses. Because your washer uses two separate single-function valves rather than one combined valve, a fault on the cold side only affects cold fills while the hot valve (W11688994) keeps working independently. If cold-specific cycles are the ones failing, this cold valve is the correct part to replace.
Do I need to replace both the hot and cold valves at the same time?
Not necessarily. Since these are independent single-function valves, you only need to replace the one that has actually failed. If only cold fills are affected, replacing this W11688995 valve alone is sufficient. If both hot and cold fills are having problems, or if the valves are original and quite old, some people choose to replace both at once since they're already accessing the same area — but it's not required.
My washer shows an F8 E1 or LO FL error. Does that mean this valve is bad?
It's a strong indicator, but check the basics first. These codes generally mean the control didn't see water reach the expected level within its allotted fill time. Before replacing the valve, confirm the cold supply valve at the wall is fully open, check the inlet screen inside the valve port for sediment or debris, and make sure the cold fill hose isn't kinked. If those check out and cold water still won't fill properly, this valve is the likely cause.
Can I use this valve on the hot water side instead?
No. This is a dedicated cold-water valve, and the hot-water side uses a separate part number, W11688994. The two are built and calibrated for their specific supply line and are not interchangeable — installing the cold valve on the hot side (or vice versa) will not properly control water temperature during the cycle.
Is this an OEM or aftermarket part?
This is a genuine OEM part, manufactured by Whirlpool to factory specifications — guaranteed fit, materials, and performance. It includes the same two-coil solenoid design, seal, and flow-rate calibration as the cold water inlet valve originally installed in your front-load washer.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
WP3363394 Genuine OEM Washer Drain Pump
The WP3363394 is a genuine Whirlpool OEM drain pump for direct-drive (no-belt) Whirlpool, Kenmore, Maytag, KitchenAid, Estate, Roper, Crosley, and Inglis top-load washers. This pump mounts directly to the washing machine's motor using two clips, and removes water from the tub during the drain portion of the wash cycle. It has one large port and one small port for its hose connections.
Over time, the pump can become locked up internally, or a small object can get lodged inside and clog it, preventing normal drainage. Symptoms of a failing pump include the washer not draining at all, or a small leak appearing near the front of the washer from a defective pump. A DIY replacement typically takes about 10 to 15 minutes. It directly replaces 3363394, WP3363394VP, AP6008107, 21024, 3296, 3348014, 3348015, 3348215, 3352492, 3352493, 3352292, 3352293, 62516, 63347, 64076, 8235, PS11741239, EAP11741239, and 1195967.
Quick Answer
The WP3363394 Genuine OEM Washer Drain Pump fixes direct-drive Whirlpool, Kenmore, Maytag, KitchenAid, Estate, Roper, Crosley, and Inglis top-load washers that aren't draining, or are leaking near the front of the unit. Mounts to the motor with two clips; one large port, one small port. Replaces 3363394, WP3363394VP, AP6008107, 21024, 3296, 3348014, 3348015, 3348215, 3352492, 3352493, 3352292, 3352293, 62516, 63347, 64076, 8235, PS11741239, EAP11741239, 1195967. This pump is specifically for direct-drive (no-belt) washers — confirm your washer's drive type before ordering.
Common Problems This Part Fixes
Washer not draining — standing water left in the tub after a cycle
Small leak near the front of the washer
Pump that has locked up or become clogged with a small object
Cycle stalling at the drain step and never advancing
Unusual noise coming from the pump during the drain phase
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This washer drain pump directly replaces the following OEM and cross-reference part numbers:
WP3363394, 3363394, 21024, 3296, 3348014, 3348015, 3348215, 3352492, 62516, 63347, 64076, 8235, AP6008107, AWP47721, EAP11741239, PD00002328, PS11741239
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This drain pump is compatible with select direct-drive Whirlpool top-load washers, and also fits select Kenmore, Maytag, KitchenAid, Estate, Roper, Crosley, and Inglis washers built on the Whirlpool platform, including model numbers such as WET4024EW, LTE5243DQ, LTE5243DQA, LTG5243DQ, CAM2742TQ, MAT14PDAWW, LSW9750PQ3, TAWS850PQ2, LSR7233EQ, and Kenmore 110.26812690 and 110.28522701.
Note: This pump is designed specifically for direct-drive (no-belt) washers. Belt-drive models use a different pump design. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure which pump your washer needs.
Key Features
Genuine Whirlpool OEM part — factory-specified pump design for direct-drive washers
Mounts directly to the motor with two clips
Resolves "not draining" and "leaking near the front of the washer" symptoms caused by pump failure
One large port, one small port for hose connections
Factory Certified Part built to Whirlpool's engineering specifications
Direct drop-in replacement — matches the original mounting and hose connections
Replaces 3363394, WP3363394VP, AP6008107, 21024, 3296, 3348014, 3348015, 3348215, 3352492, 3352493, 3352292, 3352293, 62516, 63347, 64076, 8235, PS11741239, EAP11741239, and 1195967
Compatible with Whirlpool, Kenmore, Maytag, KitchenAid, Estate, Roper, Crosley, and Inglis top-load washers
Genuine OEM replacement — guaranteed fit, materials, and performance
DIY-friendly repair, typically 10 to 15 minutes
Product Specifications
Part Number
WP3363394
Part Type
Washer Drain Pump
Condition
Genuine OEM
Brand
Whirlpool
Application
Direct-Drive (No-Belt) Top-Load Washers
Mounting
Direct to motor, secured with two clips
Ports
1 large port, 1 small port
Companion Clip
WP8546127 (recommended addition)
Repair Difficulty
Easy — 10 to 15 minutes
Quantity
1 drain pump
Compatible Brands
Whirlpool, Kenmore, Maytag, KitchenAid, Estate, Roper, Crosley, Inglis
Installation Notes
⚠️ Unplug Washer Before Starting Disconnect power at the outlet or shut off the circuit breaker before beginning. Wear work gloves. Remove the two screws securing the top panel of the washer, then carefully lift off the panel and set it aside. Disconnect the hoses connected to the drain pump by squeezing the clamps and pulling them off, then disconnect the wires from the terminals. Using a Phillips-head screwdriver, unscrew the four screws around the old pump and carefully lift it out. Take the new WP3363394 and place it into the same position as the old one, securing it with the screws. Attach the hoses back onto their ports and plug the wires back into the terminals. Reinstall the top panel and secure its screws. Restore power and run a test cycle to confirm the washer drains completely with no leaks. Tools needed: multi-screwdriver, standard pliers, work gloves.
Frequently Asked Questions
My washer isn't draining. Is this the right pump?
Yes, this is the most direct symptom of a failed drain pump. If the pump has locked up internally or become clogged by a small object, water won't be removed from the tub during the drain phase, leaving standing water behind after the cycle finishes.
How do I know if my washer is direct-drive or belt-drive?
This pump is specifically designed for direct-drive washers, which don't use a belt to connect the motor to the transmission. If you're not sure which type your washer uses, check your model number against the compatibility list, or contact our support team for confirmation before ordering, since belt-drive washers require a different pump design.
Should I replace the mounting clips at the same time?
It's worth considering, especially if your original clips show wear or damage. The companion clip, WP8546127, is commonly recommended alongside this pump since it secures the pump to the motor, and replacing a worn clip at the same time can help ensure a secure fit for the new pump.
Is this an OEM or aftermarket part?
This is a genuine OEM part, manufactured by Whirlpool to factory specifications — guaranteed fit, materials, and performance. It matches the original pump design, port configuration, and motor mounting of the drain pump originally installed in your washer.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
Genuine OEM WP3387134 Dryer Cycling Thermostat
The Genuine OEM Whirlpool WP3387134 is a dryer cycling thermostat, the operating thermostat that controls drying temperature. It switches the heating element off when the dryer reaches its set temperature and back on after it cools, keeping the inside of the dryer at a steady temperature throughout the cycle. This one is rated L155-25: it cuts out at approximately 155°F and cycles back on once the temperature drops about 25°F.
When a cycling thermostat fails, the dryer may stop heating, run too hot, or keep heating after the drum has stopped. This is the original Whirlpool part, and it fits a wide range of Whirlpool-built dryers sold under the Whirlpool, Kenmore, Maytag, KitchenAid, Roper, Crosley, Estate, Amana, and other brand names.
Quick Answer
The Genuine OEM WP3387134 Cycling Thermostat fixes a Whirlpool-built dryer that isn't heating, runs too hot, or has inconsistent drying temperatures. Rated L155-25, it cycles the heating element off at about 155°F and back on after a 25°F drop. Classic symptom: clothes come out damp or the dryer runs excessively hot, with no sign of a clogged vent.
Common Problems This Part Fixes
Dryer not heating
Dryer running too hot
Inconsistent drying temperatures
Heat staying on after the drum has stopped
Dryer won't start or the timer doesn't advance, if the thermostat has failed
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This cycling thermostat directly replaces the following part numbers:
WP3387134, 3387134, 2011, 2893, 3-6910, 306910, 3387135, 3387139, ET187, EAP11741405, WP3387134VP, AP6008270, AWP47432, EAP11741405, PD00002313, PS11741405, L155-25F
These numbers span several generations of Whirlpool's own part numbering for this thermostat as model lines were updated. All are the correct replacement regardless of which number appears on your dryer's parts diagram.
Compatibility
This thermostat fits a wide range of Whirlpool, Kenmore, Maytag, KitchenAid, Roper, Crosley, Estate, Amana and related dryers, including these examples:
Kenmore 11060012000, 11060012001, 11060022010, 11060172000, 11060232000, 11060602990
Numerous additional Whirlpool-built dryer models
Note: This is the cycling (operating) thermostat, not the high limit thermostat or the thermal fuse, which are separate safety parts. The models above are a sample, not a full list. Confirm your model number against your dryer's parts diagram, or contact our support team to verify fit before ordering.
Key Features
Genuine OEM Whirlpool cycling thermostat
Rated L155-25: cuts out at about 155°F and cycles back on after a 25°F drop
Keeps dryer temperature steady by cycling the heating element on and off
Resolves no-heat, overheating, and inconsistent-temperature symptoms
Fits Whirlpool, Kenmore, Maytag, KitchenAid, and other Whirlpool-built dryers
Medium-difficulty repair with basic hand tools
Product Specifications
Part Number
WP3387134
OEM Part Number
WP3387134
Part Type
Dryer Cycling Thermostat
Condition
Genuine OEM
Temperature Rating
L155-25 (Cuts Out ~155°F, 25°F Differential)
Application
Whirlpool, Kenmore, Maytag, KitchenAid & Related Dryers
Installation Notes
⚠️ Unplug Power Before Installing Unplug the dryer or switch off its circuit breaker before beginning, and shut off the gas supply first on gas models. Wear work gloves, as the cabinet edges are sharp. Remove the panel that gives access to the heater housing per your model's service guide, note the wire terminal positions, and disconnect them from the old thermostat. Remove the thermostat, install the new one in the same position, and reconnect the wires. A screwdriver and needle-nose pliers are typically all you need. Before closing the dryer, clean the lint trap and check the exhaust vent for restrictions, since poor airflow is a common cause of overheating.
Frequently Asked Questions
My dryer isn't heating or runs too hot. Is this the part I need?
A failed cycling thermostat can cause either symptom. It may stay open and prevent heat, or stay closed and let the dryer overheat. Check for a clogged vent and test the thermostat for continuity before replacing it.
What's the difference between the cycling thermostat and the high limit thermostat?
The cycling thermostat controls normal drying temperature by switching the heating element on and off. The high limit thermostat and thermal fuse are separate safety devices that cut power if the dryer overheats. This listing is for the cycling thermostat only.
How do I test this thermostat?
With the dryer unplugged and the wires removed, check for continuity across the terminals with a multimeter at room temperature. A properly working cycling thermostat should show continuity when cool. No continuity means it has failed.
Will this fit my dryer?
It fits many Whirlpool-built dryers, but the model list above is only a sample. Check your model number against your parts diagram, or contact our support team and we'll verify it before you order.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping ✓ Genuine OEM Parts ✓ Compatibility Support ✓ Secure Checkout
W11210459 Genuine OEM Whirlpool Washer Water Inlet Valve
The W11210459 is a genuine Whirlpool OEM water inlet valve for Whirlpool top-load washers, and also fits select Kenmore, Maytag, Amana, Crosley, Inglis, and Roper models. This valve controls the flow of hot and cold water into the tub during the fill portion of each cycle — an electrical solenoid opens and closes the valve to admit exactly the right amount of water for the selected wash setting.
Over time, mineral or sediment buildup inside the valve, or general wear in the solenoid coil, can cause the valve to fail. A failing valve typically shows up as the washer not filling with water, filling very slowly, or water continuing to leak into the tub after the wash has completed. It directly replaces AP6329217, W10701459, W10838319, W11038711, 4591321, PS12349267, W10869799, W11025984, and W11210459VP.
Quick Answer
The W11210459 Genuine OEM Whirlpool Washer Water Inlet Valve fixes Whirlpool, Kenmore, Maytag, Amana, Crosley, Inglis, and Roper top-load washers that won't fill, fill very slowly, or continue leaking water into the tub after the wash has finished. Replaces AP6329217, W10701459, W10838319, W11038711, 4591321, PS12349267, W10869799, W11025984, W11210459VP. The control panel can be removed more easily with a putty knife slid under each end to release the clips, rather than removing the back panel first.
Common Problems This Part Fixes
Washer not filling with water
Washer filling very slowly
Water continuing to leak into the tub after the wash cycle has completed
No hot water reaching the tub, or no cold water reaching the tub
Cycle stalling at the fill step and never advancing to wash
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This washer water inlet valve directly replaces the following OEM and cross-reference part numbers:
W11210459, W10701459, W10838319, W11038711, 4591321, W10869799, W11025984, 33190189, 33190190, W10423122, W10423124, W10868380, W10868381, AP6329217, AWP43369, EAP12349267, OEM18987660, PD00042885, PS12349267
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This water inlet valve is compatible with select Whirlpool top-load washers, and also fits select Kenmore, Maytag, Amana, Crosley, Inglis, and Roper washers built on the Whirlpool platform, including model numbers such as WTW5000DW1 and WTW4816FW2.
Note — not the same as W11210463: A similarly-numbered valve, W11210463 (also cross-referenced as W11101906), is a separate part with its own cross-reference set (W10701461, W10883458, W10869803, W11038696, AP6329219), used on other Whirlpool washer models. The two are easy to confuse given how close the numbers are — always confirm you have the exact part number before ordering. Contact our support team with your model number if you're unsure.
Key Features
Genuine Whirlpool OEM part — factory-specified solenoid design and flow rate
Regulates hot and cold water flow into the washer tub
Resolves "won't fill," "fills slowly," and "leaks after cycle completes" symptoms caused by valve failure
Factory Certified Part built to Whirlpool's engineering specifications
Direct drop-in replacement — matches the original mounting and hose connections
Replaces AP6329217, W10701459, W10838319, W11038711, 4591321, PS12349267, W10869799, W11025984, and W11210459VP
Compatible with Whirlpool, Kenmore, Maytag, Amana, Crosley, Inglis, and Roper top-load washers
Genuine OEM replacement — guaranteed fit, materials, and performance
Moderate DIY repair
Product Specifications
Part Number
W11210459
Part Type
Washer Water Inlet Valve
Condition
Genuine OEM
Brand
Whirlpool
Application
Top-Load Washers
Function
Controls hot and cold water flow into the tub
Repair Difficulty
Moderate
Quantity
1 valve
Compatible Brands
Whirlpool, Kenmore, Maytag, Amana, Crosley, Inglis, Roper
Installation Notes
⚠️ Unplug Washer And Shut Off Water Supply Before Starting — Use A Putty Knife To Release The Control Panel Disconnect power at the outlet, or shut off the house circuit breaker for the appliance, and shut off both hot and cold water supplies before beginning. Wear work gloves. The top control panel can be removed more easily by sliding a putty knife under the panel on each end to release the retaining clips, rather than removing the back panel first — one customer specifically noted this trick saved considerable time after trying the back-panel approach without success. With the panel released, locate the water inlet valve and photograph the wiring and hose connections before disconnecting anything. Disconnect the electrical connector and the hot/cold water lines from the old valve, remove its mounting screws, and pull it free. Install the new W11210459 in the same position, reconnect the water lines and electrical connector fully, and secure the mounting screws. Reinstall the control panel. Restore the water supply and power, then run a full test cycle across a few temperature settings to confirm correct fill behavior with no leaking. Tools needed: multi-screwdriver, putty knife, work gloves.
Frequently Asked Questions
My washer isn't filling with water. Is this the right part?
Yes, this is the most direct symptom of a failed water inlet valve. Since this valve is what admits water from your household supply into the washer, a solenoid failure or internal blockage can prevent any water from entering at all, stopping the wash cycle from proceeding.
What's the easiest way to access the control panel for this repair?
Try sliding a putty knife under the panel at each end to release the retaining clips, rather than removing the back panel of the washer first. One customer specifically learned this trick after trying the back-panel approach with no luck, then found the putty knife method worked cleanly after watching an online tutorial.
Is this the same as W11210463?
No, these are two separate Whirlpool valve part numbers with different cross-reference sets, despite the similar numbering. Always confirm the exact part number from your washer's parts diagram or the sticker on your old valve rather than assuming based on a close number match.
Is this an OEM or aftermarket part?
This is a genuine OEM part, manufactured by Whirlpool to factory specifications — guaranteed fit, materials, and performance. It matches the original solenoid design, flow rate, and connection type of the water inlet valve originally installed in your washer.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
XPARTCO DC97-16350U Washer Suspension Rod Kit (Set of 4)
The XPARTCO DC97-16350U is an aftermarket replacement washer suspension rod kit (set of 4) compatible with a wide range of Samsung top-load washers in the WA40, WA41, WA42, WA44, WA45, WA49, and WA50 series. The suspension rods are spring-loaded shock-absorbing rods that connect the outer washer tub to the top corners of the cabinet frame, suspending the tub and dampening the vibrations generated during agitation and high-speed spin cycles. When one or more rods lose tension, break, or degrade, the tub swings off-center and strikes the cabinet walls — causing violent shaking, loud banging, error code dc (out of balance), UE imbalance errors, and progressive damage to the machine.
Each rod measures 26.4–26.5 inches in overall length and 1-1/4 inches in diameter, constructed from spring steel with plastic end caps. The kit includes all 4 suspension rods — always replace all four at the same time since they wear at the same rate. It directly replaces DC97-16350S, DC97-16350T, DC97-16350E, DC97-16350C, DC97-16350D, DC97-16350K, DC97-05280W, 4962798, AP6884450, EAP12720841, PS12720841, and PD00065434. Wear gloves during installation — the rods are coated with grease. Installs in 20–30 minutes — no special tools required.
Quick Answer
The XPARTCO DC97-16350U Washer Suspension Rod Kit fixes Samsung top-load washers that vibrate violently, bang loudly, walk across the floor, or display dc or UE imbalance error codes during spin. Set of 4 rods, 26.4–26.5" long, 1-1/4" diameter, spring steel with plastic end caps. Replace all 4 at the same time. Wear gloves — rods are greased. Compatible with Samsung WA40–WA50 series. Replaces DC97-16350S, DC97-16350T, DC97-16350E, DC97-16350C, DC97-16350D, AP6884450, PS12720841.
Common Problems This Kit Fixes
Washer vibrating violently or shaking excessively during the spin cycle
Loud banging or thumping — tub striking the cabinet walls during spin
Washer "walking" or moving across the floor during high-speed spin
Error code dc displayed — Samsung out-of-balance error during spin
Error code UE displayed — unbalanced load error the washer cannot self-correct
Washer repeatedly stopping and rebalancing the load without completing the spin cycle
Visible broken, detached, or sagging suspension rod inside the washer cabinet
Rattling or clunking during agitation — tub no longer centered
Replaces Part Numbers
This suspension rod kit directly replaces the following OEM and cross-reference part numbers:
DC97-16350U, DC97-16350S, DC97-16350T, DC97-16350E, DC97-16350C, DC97-16350D, DC97-16350J, DC97-16350K, DC97-16350U, DC97-16350E, DC97-16350S, DC97-16350C, DC97-16350D, DC97-16350T, AP6884450, ASM34747, EAP12720841, PD00065434, PS12720841.
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This suspension rod kit is compatible with select top-load washers from the following Samsung series:
Samsung WA40 series — WA400PJHDWR, WA40J3000AW, WA40A3005AW, WA44A3205AW and related models
Samsung WA41 series — WA41A3000AW and related models
Samsung WA42 series — WA422PRHDWR and related models
Samsung WA45 series — WA45H7000AW, WA45H7200AW, WA45K7600AW, WA45M7050AW, WA45N3050AW, WA45T3200AW, WA45T3400AW, WA45T3400AP, WA456DRHDSU, WA456DRHDWR and related models
Samsung WA49 series — WA49B5105AW, WA49B5205AW and related models
Samsung WA50 series — WA50R5200AW, WA50R5400AV, WA50R5400AW, WA50T5300AC and related models
Kenmore / Sears top-load washers (select Samsung-built models)
Important: The DC97-16350U rod is 26.4–26.5 inches long and is for Samsung WA40–WA50 series washers. Larger-capacity WA48–WA54 series models use the longer DC97-16350V rod (27.5 inches). Always measure your existing rods or verify your model number before ordering — using the wrong length rod can cause the tub to sit at the incorrect height inside the cabinet.
Key Features
Set of 4 suspension rods — complete replacement covering all four tub mounting points
Suspends and centers the outer tub within the cabinet — dampens agitation and spin vibration to prevent tub-to-cabinet contact
Resolves Samsung error codes dc (out of balance) and UE (unbalanced load)
Rod length: 26.4–26.5 inches overall; diameter: 1-1/4 inches
Spring steel construction with plastic end caps — durable and corrosion resistant
Rods are pre-coated with grease — wear work gloves during installation
Replace all 4 rods at the same time — rods wear together and partial replacement results in uneven tub support
No special tools required — installs in 20–30 minutes
Replaces DC97-16350S, DC97-16350T, DC97-16350E, DC97-16350C, DC97-16350D, and over 15 additional cross-references
Aftermarket replacement built to OEM-equivalent quality standards
Product Specifications
Part Number
DC97-16350U
Part Type
Washer Suspension Rod and Spring Assembly
Condition
Aftermarket Replacement
Application
Samsung Top-Load Washers — WA40, WA41, WA42, WA44, WA45, WA49, WA50 series
Quantity
Set of 4 (replace all four rods at the same time)
Rod Length
26.4–26.5 inches overall
Rod Diameter
1-1/4 inches
Material
Spring steel / Plastic end caps
Color
Brass / Black / White / Pink
Lubrication
Pre-coated with grease — wear gloves during installation
Error Codes Resolved
dc (out of balance), UE (unbalanced load)
Compatible Brands
Samsung, Kenmore (Samsung-built)
Installation Notes
⚠️ Unplug Washer and Shut Off Water Before Starting — Wear Gloves Disconnect power and turn off the water supply before beginning. Wear work gloves throughout — the suspension rods are coated with grease. Remove the lid and the top panel (typically secured by screws under the lid hinge covers and at the rear corners). With the top panel removed, the four suspension rods are visible at the corners, each running from a mounting point on the tub rim up to a hook or bracket at the top corners of the cabinet frame. Note the orientation and attachment method of each rod before removing. Unhook the top of each rod from the cabinet bracket and lift the bottom cup off the tub mounting pin. Install each new DC97-16350U rod by seating the bottom cup onto the tub mounting pin and hooking the top over the cabinet bracket. Replace all four rods before reassembling. Reinstall the top panel and lid, restore power and water, and run a spin cycle to verify smooth, quiet, centered operation. Tools needed: Phillips screwdriver; no special tools required for the rods themselves.
Frequently Asked Questions
What is the difference between DC97-16350U and DC97-16350V?
Both are Samsung top-load washer suspension rods, but they are different lengths for different washer capacity generations. The DC97-16350U is approximately 26.4–26.5 inches long and is used on mid-capacity Samsung WA40 through WA50 series washers. The DC97-16350V is approximately 27.5 inches long and is used on larger-capacity WA48 through WA54 series washers. Using the wrong length rod causes the tub to sit at the wrong height inside the cabinet, which can cause new imbalance issues. Always measure your existing rods or verify your model number before ordering.
Why must I replace all 4 rods instead of just the broken one?
All four suspension rods experience the same amount of wear over the same number of wash cycles. When one rod fails, the remaining three have experienced the same stress and fatigue and are likely to fail soon after. Replacing only the broken rod leaves three worn rods supporting the tub unevenly — this can cause continued vibration, accelerate wear on the new rod, and require a second repair shortly after. Replacing all four at the same time ensures even tub support, fully resolves the imbalance, and prevents a repeat repair.
Do DC97-16350S, DC97-16350T, and DC97-16350E all cross to the DC97-16350U?
Yes — DC97-16350S, DC97-16350T, DC97-16350E, DC97-16350C, and DC97-16350D are all cross-reference part numbers for the same Samsung suspension rod assembly used across different production runs of the same washer series. Samsung updates part number suffixes during production revisions. All of these numbers have the same 26.4–26.5" length and are interchangeable with the DC97-16350U.
What do error codes dc and UE mean on Samsung washers?
Error code dc on Samsung top-load washers indicates the machine has detected an out-of-balance condition and stopped spinning to prevent damage. Error code UE indicates an unbalanced load that the washer cannot self-correct by redistributing. Both codes can be caused by an overloaded or unevenly distributed laundry load — but if the errors occur consistently even with normal, balanced loads, worn or broken suspension rods are the most common mechanical cause. Replacing the rod kit resolves these errors in most cases.
Is this an OEM or aftermarket part?
This is an aftermarket replacement kit built to OEM-equivalent quality standards. It is not a genuine Samsung OEM part, but is manufactured from spring steel with plastic end caps to match the length and spring tension of the original DC97-16350U suspension rods.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout
Genuine OEM W11399437 Washer Drain Pump Assembly
The Genuine OEM Whirlpool W11399437 is the drain pump assembly for select Whirlpool and Maytag washers. It pumps the water out of the washer during the drain stage of the cycle. When the pump fails or clogs, the washer may not drain properly, leave water in the drum, or stop partway through a cycle.
This is the original Whirlpool part, not an aftermarket equivalent. It is sold as an assembly, which may include more than one component, so check the parts diagram for your model to confirm what comes with it. Check your model number before ordering.
Quick Answer
The Genuine OEM W11399437 Washer Drain Pump Assembly replaces a failed or clogged drain pump on a compatible Whirlpool or Maytag washer. Replaces W11259498. Classic symptoms: the washer won't drain, leaves water in the drum, or stops mid-cycle.
When To Replace This Part
Washer won't drain or leaves water in the drum
Washer stops or won't advance after the wash cycle
Drain pump is noisy, leaking or seized
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This drain pump assembly replaces or supersedes the following part numbers:
W11399437 replaces W11259498, AP6974144, 10minON50minOFF, Hanyu B25-3A04, AWP44240, EAP12731241, PD00058225, PS12731241
If your old pump shows a different number, contact our support team and we'll check whether it matches.
Compatibility
This drain pump assembly is listed for select Whirlpool and Maytag washers, including these examples:
Maytag MVW6200KW1, MVW6200KW2, MVW4505MW1, MVW4505MW2
Maytag MVW6230RHW2, MVW6230RHW3, MVW6230HW3
Maytag MVW5035MW1, MVW6500MW0, MVWC565FW3
Note: The models above are a sample, not a full list. Whirlpool uses other drain pumps on other washers, so check your full model number against your parts diagram, or contact our support team to verify fit before ordering.
Key Features
Genuine OEM Whirlpool part, not an aftermarket equivalent
Drain pump assembly that removes water during the drain stage
Replaces the earlier W11259498 part number
Sold individually
Product Specifications
Part Number
W11399437
OEM Part Number
W11399437
Part Type
Washer Drain Pump Assembly
Condition
Genuine OEM
Manufacturer
Whirlpool
Quantity
1 Assembly
Application
Select Whirlpool and Maytag Washers
Installation Notes
⚠️ Unplug The Washer And Drain Remaining Water Unplug the washer and shut off the water supply before you start. Water can remain in the pump and hoses, so have towels and a shallow pan ready. Take a photo of the wiring and hose connections before disconnecting anything, then transfer them to the new pump in the same positions and secure the clamps. If the washer still won't drain, check the drain hose and filter for a clog, and the wiring and control board.
Frequently Asked Questions
My washer won't drain. Is the pump the fix?
Often, but not always. A clogged drain hose or filter, a kinked hose, or a wiring or control problem can cause the same symptom, so check those before replacing the pump.
Is this an OEM or aftermarket part?
This is a genuine OEM part from Whirlpool, not an aftermarket equivalent.
What comes in the assembly?
It is a drain pump assembly and may include more than one part. Check the parts diagram for your model, or contact our support team and we'll confirm before you order.
Will this fit my washer?
It is listed for many Whirlpool and Maytag washers, but the model list above is only a sample. Check your full model number against your parts diagram, or contact our support team and we'll verify it before you order.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping ✓ Genuine OEM Parts ✓ Compatibility Support ✓ Secure Checkout
AHA75673401 Washer Genuine Drain Pump
Fits Specific LG Washer models
Description: This Washing Machine Drain Pump is an OEM part for specific LG washing machine models. It is responsible for effectively draining water out of the washing machine after each cycle. The pump works to remove water from the tub and drain hoses, preparing the machine for the next load.
Replaces Part Numbers: AHA75673401, 4873470, AP6335290, PS12580277.
California Residents only
WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov
XPARTCO 12138200000320 Dryer Door Catch
The XPARTCO 12138200000320 is an aftermarket replacement dryer door catch compatible with select Midea and Insignia dryers. The door catch is a small plastic spring-clip mechanism mounted on the dryer door that snaps over the door strike o12138200000320 n the cabinet opening to hold the door firmly closed during operation. When the door is closed and latched, the door switch is activated — signaling the control board that it is safe to run. When the catch breaks, cracks, or loses its spring tension, the door will not stay closed, the door switch will not activate properly, and the dryer will either not start or will stop mid-cycle.
This is a snap-in replacement catch — the color or exact finish may vary by production run. It directly replaces AP7152622 and PS18161385. Sold individually. Installs in under 5 minutes — no tools required in most cases.
Quick Answer
The XPARTCO 12138200000320 Dryer Door Catch fixes Midea and Insignia dryers where the door won't stay closed, pops open during a cycle, or where the dryer won't start because the door switch isn't being activated. Snap-in installation — no tools required, installs in under 5 minutes. Sold individually. Replaces AP7152622, PS18161385.
Common Problems This Part Fixes
Dryer door will not stay closed during the drying cycle
Door pops open mid-cycle, stopping the dryer
Dryer will not start — door switch not being activated by a worn or broken catch
Door feels loose or does not click shut firmly when closed
Door catch visibly cracked, broken, or missing
Dryer requires the door to be held or pushed to stay running
Replaces Part Numbers
This door catch directly replaces the following part numbers:
12138200000320, AP7152622, PS18161385.
Contact our support team with your model number if you need confirmation before ordering.
Compatibility
This door catch is compatible with select dryers from the following brands:
Midea dryers (gas and electric — select models)
Insignia dryers (select models)
Always verify your appliance model number before ordering. Contact our support team if you're unsure.
Key Features
Holds the dryer door closed and activates the door switch so the dryer can run safely
Snap-in installation — no tools required in most cases; installs in under 5 minutes
Durable plastic construction — designed to withstand repeated opening and closing
Sold individually — one door catch per order
Replaces AP7152622 and PS18161385
Aftermarket replacement built to OEM-equivalent quality standards
Product Specifications
Part Number
12138200000320
Part Type
Dryer Door Catch (Door Latch Clip)
Condition
Aftermarket Replacement
Application
Gas and Electric Dryers
Material
Plastic
Installation
Snap-in — no tools required
Sold As
Single door catch
Compatible Brands
Midea, Insignia
Installation Notes
⚠️ Unplug Dryer Before Starting Disconnect power before beginning. Open the dryer door and locate the old door catch — it is a small plastic clip mounted on the inside of the door or on the cabinet opening around the door. Press the tabs on the old catch to release it from its mounting slot and pull it free. Note the orientation before removing. Insert the new 12138200000320 catch into the slot in the same orientation and press firmly until it snaps into place. Close the door to confirm it latches securely. Restore power and run a short cycle to verify the door stays closed and the dryer operates normally. Tools needed: None in most cases; a small flat-head screwdriver may help with removal.
Frequently Asked Questions
What dryers is the 12138200000320 compatible with?
The 12138200000320 door catch is used on select Midea and Insignia dryer models. Insignia is a Best Buy house brand whose appliances are manufactured by Midea. Always verify your exact model number before ordering to confirm this catch fits your dryer's door latch assembly.
Why won't my dryer start even though I'm closing the door?
If the door catch is broken or worn, the door may not be engaging the door switch firmly enough to signal the control board that the door is closed. Most dryers will not run unless the door switch is fully activated. Replacing the 12138200000320 catch restores the firm snap needed to trigger the switch. If replacing the catch does not resolve the start issue, the door switch itself may also need to be checked.
Do I need to replace the door strike as well?
Not necessarily. In most cases only the door catch (the spring-clip on the door) needs replacement. The door strike (the post or tab on the cabinet that the catch snaps onto) is typically more durable. Inspect the strike for cracks or breakage before ordering — if it is intact, just the 12138200000320 catch is all you need.
Is this an OEM or aftermarket part?
This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Midea OEM part, but is manufactured from durable plastic to match the dimensions and function of the original 12138200000320 door catch.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout
W11568627 Genuine OEM Whirlpool/Kenmore Dryer Drum Belt
The W11568627 is a genuine OEM drum (cylinder) belt for select Whirlpool and Kenmore front-load dryers. This belt wraps around the outside of the drum and routes around the drive motor pulley and idler pulley — it's what actually spins the drum during a drying cycle while the motor and blower keep running independently. Over time this belt stretches, glazes, or cracks from heat and friction, and it eventually slips or snaps, leaving the drum motionless even though the rest of the dryer still runs.
Manufactured by Whirlpool to factory spec for smooth, durable drum operation under high-demand drying cycles, this is a genuine OEM part — not an aftermarket equivalent — so fit and long-term performance match what came on the dryer originally.
Quick Answer
The Genuine OEM W11568627 Dryer Drum Belt fixes a Whirlpool or Kenmore dryer whose drum won't spin, or that runs with a rubbing/thumping noise from the drum area. Genuine OEM replacement, factory fit. Classic symptom: motor and airflow run normally, but the drum sits still — or a rubbing sound right before the belt fails completely.
Common Problems This Part Fixes
Dryer runs (motor and airflow work) but the drum doesn't spin
Rubbing, squealing, or thumping noise from inside the dryer during operation
Clothes bunch up in one spot instead of tumbling
Burning rubber smell from a slipping or overheating belt
Visible cracking, glazing, or fraying on the old belt
Dryer drum spins freely by hand with no resistance from the motor
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This drum belt directly replaces the following part number:
W11568627, W10577771, AP7175918, AWP45299, EAP16660508, OEM21527763, PD00070745, PS16660508
W10577771 is the previous Whirlpool part number for this belt; W11568627 is the current production number. We were not able to confirm additional cross-reference numbers beyond these two at this time. If you have one, contact our support team before ordering and we will verify compatibility.
Compatibility
This drum belt is compatible with the following Whirlpool and Kenmore dryer models:
11061632610, 11061632611
11061633610, 11061633611, 11061633612
11071632610, 11071633610, 110C61633610
WED9500EC0, WED9500EW0, WGD9500EC0, WGD9500EW0
Note: Not all applicable models are necessarily listed above — this is the compatibility data we were able to confirm from available sourcing, and Whirlpool may use this belt on additional models not shown here. Confirm the belt shown on your dryer's parts diagram matches this part number, or contact our support team with your model number to verify before ordering.
Key Features
Genuine OEM drum belt — factory fit and durability, not an aftermarket equivalent
Drives drum rotation during the drying cycle
Built for smooth, reliable operation under high-demand drying cycles
Resolves drum-not-spinning, rubbing/thumping noise, and slipping-belt symptoms
Direct replacement for both W11568627 and the earlier W10577771 numbering
One-year manufacturer replacement warranty on genuine parts
Product Specifications
Part Number
W11568627
OEM Part Number
W11568627
Part Type
Dryer Drum (Cylinder) Belt
Condition
Genuine OEM
Application
Whirlpool & Kenmore Dryers
Country of Origin
Mexico
Installation Notes
ℹ️ Unplug Power Before Installing Unplug the dryer or switch off its circuit breaker before beginning. Remove the dryer's front or rear access panel per your model's service guide to reach the drum, motor pulley, and idler pulley. Release tension on the idler pulley to slip the old belt off, and note the belt's routing path around the drum and pulleys before removing it — a photo taken beforehand makes reinstallation much easier. Loop the new belt around the drum with the ribbed side against the drum surface, then route it around the motor pulley and back around the idler pulley in the same path as the original, making sure it isn't twisted. Reinstall the idler pulley to restore proper tension, then rotate the drum by hand to confirm the belt tracks straight and doesn't rub before closing up the panel.
Frequently Asked Questions
My dryer runs but the drum won't turn — is this the part I need?
Yes, in most cases. A broken or badly slipped drum belt is the most common cause of a dryer that powers on, runs the motor and blower, and still produces heat and airflow, but the drum itself sits motionless.
Is W10577771 the same belt as W11568627?
Yes. W10577771 was the earlier Whirlpool part number for this belt; W11568627 is the current production number for the same design. If your dryer's parts diagram shows W10577771, this part is the correct current replacement.
My exact model isn't listed — will this still fit?
Possibly. Whirlpool uses this belt across a range of models beyond what's confirmed in our current compatibility data. Contact our support team with your full model number and we'll verify fit before you order.
Do I need to replace the idler pulley at the same time?
Not necessarily — this listing is for the belt only. However, if your idler pulley is worn, noisy, or doesn't spin freely, it's worth inspecting and replacing while the dryer is already apart, since a bad idler pulley can shorten the life of a new belt.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout
