Search results for "Dryer belts and idler pulley"

XPARTCO W10464673 Refrigerator Evaporator Fan Motor Replaces WPW10464673 The XPARTCO W10464673 is an aftermarket replacement refrigerator evaporator fan motor compatible with select Whirlpool, KitchenAid, Maytag, Kenmore, and Ikea bottom-freezer and French door refrigerators. The evaporator fan motor is located inside the freezer compartment and circulates cold air from the evaporator coils throughout both the freezer and fresh food sections. Without the evaporator fan running, cold air cannot be distributed — even if the compressor and evaporator are working correctly, both compartments will gradually warm up. A failed evaporator fan motor is one of the most common causes of a refrigerator that runs but does not cool. Rated 115V, 60Hz with a 2-pin connector, this motor features a 14mm shaft length, 3mm shaft diameter, and approximately 13cm (5.1") of wire lead. It is constructed from ABS plastic housing with a metal motor core. It directly replaces WPW10464673, 3020513, AP6021839, PS7320664, PS11755167, and EAP11755167. Compatible models include KitchenAid KFFS and KRFF series, Maytag MFB and MFF series, and several Kenmore 106/596-series models. Installs in 20–30 minutes with basic hand tools. Quick Answer The XPARTCO W10464673 Refrigerator Evaporator Fan Motor fixes refrigerators where both compartments are too warm, the refrigerator runs but doesn't cool, or there is unusual noise from inside the freezer. 115V/60Hz, 2-pin connector, 14mm shaft, 3mm shaft diameter, 13cm leads. ABS/metal construction. Compatible with KitchenAid KFFS/KRFF, Maytag MFB/MFF, Whirlpool, and Kenmore 106/596-series. Replaces WPW10464673, 3020513, AP6021839, PS7320664, PS11755167. Common Problems This Part Fixes Both refrigerator and freezer compartments too warm — evaporator fan not circulating cold air Refrigerator running continuously but not cooling — compressor on but no air circulation Freezer section cold but fresh food section warm — fan not moving air between compartments Unusual buzzing, squealing, or grinding noise coming from inside the freezer No airflow felt inside the refrigerator or freezer when the compressor is running Fan blade visible inside the freezer but not spinning when the compressor runs Ice buildup on the evaporator coils causing the fan blade to stop Replaces Part Numbers This evaporator fan motor directly replaces the following OEM and cross-reference part numbers: WPW10464673, W10464673, 3020513, AWP50481, EAP11755167, PD00030978, AP6021839, PS11755167, FDQC16WP2A. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This evaporator fan motor is compatible with select refrigerators from the following brands and series: KitchenAid refrigerators — KFFS20 and KRFF300 series (KFFS20EYMS02, KFFS20EYBL02, KFFS20EYBL04, KRFF300EBL00, KRFF300EBS00 and related models) Maytag refrigerators — MFB2055 and MFF2055 series (MFB2055YEB01, MFB2055YEB02, MFB2055YEM01, MFB2055YEM02, MFB2055YEW02, MFF2055DRE00, MFF2055YEB02, MFF2055YEW00, MFW2055FRH00, MFB2055FRW00 and related models) Whirlpool refrigerators (select bottom-freezer and French door models) Kenmore / Sears refrigerators — 106 series and 596 series (10673002510, 10673002511, 10673003510, 10673003511, 59673002510, 59673003510, 59673003511, 59673009510, 10679472411, 10679473411 and related models) Ikea refrigerators (select models) Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Circulates cold air from the evaporator coils throughout the freezer and fresh food compartments — essential for maintaining set temperatures in both sections 115V, 60Hz — correct electrical specifications for compatible models 2-pin connector — direct plug-in replacement on compatible models Shaft: 14mm length, 3mm diameter — matches original motor shaft dimensions for fan blade compatibility Wire lead length: approximately 13cm (5.1 inches) ABS plastic housing with metal motor core — durable and designed for continuous freezer-temperature operation Replaces WPW10464673, 3020513, AP6021839, PS7320664, PS11755167, and FDQC16WP2A Compatible with KitchenAid KFFS/KRFF, Maytag MFB/MFF, Kenmore 106/596, Whirlpool, and Ikea refrigerators Aftermarket replacement built to OEM-equivalent quality standards DIY repair — installs in 20–30 minutes with basic hand tools Product Specifications Part Number W10464673 OEM Part Number WPW10464673 Part Type Refrigerator Evaporator Fan Motor Condition Aftermarket Replacement Application Bottom-Freezer and French Door Refrigerators Voltage 115V AC Frequency 60 Hz Connector 2-pin plug Shaft Length 14mm (0.55 inches) Shaft Diameter 3mm (0.12 inches) Wire Lead Length Approximately 13cm (5.1 inches) Material ABS plastic housing / Metal motor core Compatible Brands Whirlpool, KitchenAid, Maytag, Kenmore, Ikea Installation Notes ⚠️ Unplug Refrigerator and Shut Off Water Before Starting Unplug the refrigerator and shut off the water supply before beginning. Remove all food and shelving from the freezer compartment. On most compatible models, the evaporator fan is located behind the freezer back panel. Remove the screws securing the freezer back panel and carefully slide it out to expose the evaporator coils and fan assembly. If ice has built up on the fan or coils, use a hair dryer to melt it before attempting to remove the fan — do not force a frozen fan free. Disconnect the 2-pin wire connector from the old motor. Remove the fan blade by pulling it straight off the motor shaft, then unscrew the motor mounting brackets and remove the old motor. Install the new W10464673 motor in the same position, secure the mounting brackets, press the fan blade back onto the shaft, and reconnect the 2-pin connector. Reinstall the freezer back panel, restore power and water, and verify the fan runs when the compressor starts. Tools needed: Phillips screwdriver, hair dryer (if coils are iced), work gloves. Frequently Asked Questions What does the evaporator fan motor do? The evaporator fan motor drives a fan blade inside the freezer compartment that draws air across the evaporator coils — the cold coils remove heat from the air, and the fan distributes the chilled air throughout both the freezer and fresh food sections via a duct system. Without the evaporator fan running, the evaporator coils still get cold and the compressor still runs, but no cold air is circulated. This causes both compartments to gradually warm up even though the refrigeration system itself may be functioning correctly. A failed evaporator fan motor is one of the most common and most frequently misdiagnosed causes of poor refrigerator cooling. How do I know if the evaporator fan motor has failed? Open the freezer door and press the door switch (the small button or tab that tells the refrigerator the door is closed) — this should start the evaporator fan if the compressor is running. If you hear no fan noise and feel no airflow from inside the freezer with the compressor running, the fan motor has likely failed. You can also remove the freezer back panel and physically check whether the fan blade spins freely by hand — if it is stuck or wobbles, inspect for ice buildup or a seized motor bearing. If the blade spins freely but the motor does not run when powered, the motor has burned out. What is the difference between W10464673 and WPW10464673? These are the same evaporator fan motor. WPW10464673 is the updated Whirlpool OEM part number that superseded the original W10464673. The 3020513 is also a cross-reference for this same motor. This aftermarket replacement is compatible with all of these numbers. My freezer is cold but my fridge is warm — could it be the evaporator fan? Yes — this is a classic evaporator fan failure symptom. When the fan motor fails partially, the freezer may still receive some cold air passively from the evaporator, but not enough air is circulated to reach the fresh food section through the duct system. A failed evaporator fan is frequently the cause of this hot-fridge-cold-freezer pattern. Check the fan as described above — if it is not spinning, replacing the W10464673 motor will restore cooling to both compartments. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured from ABS plastic and metal to match the electrical specifications and shaft dimensions of the original W10464673 evaporator fan motor. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

W11612327 Dishwasher Genuine Circulation Pump Circulation pump and motor assembly Replaces Part Numbers: W11612327, W11024423, W10805387, W11521436, AP7194668, PS16744935. Description: This Pump is a Genuine component for specific Whirlpool dishwasher models. It refers to the water pump component that circulates water throughout the dishwasher during cycles. Common cause of a faulty pump can include normal wear over many uses. The continuous motor operation puts strain on internal seals and impellers. Mineral deposits from hard water can also clog pump parts over time.

Read more less

XPARTCO 5304519906 Dishwasher Pump and Motor Assembly Product Overview The XPARTCO 5304519906 Dishwasher Pump and Motor Assembly is designed to circulate water through the spray arms and ensure proper cleaning performance. This Motor & Pump Assembly is a replacement part for specific Frigidaire dishwasher models. This assembly is crucial for circulating water throughout the dishwasher during the wash and rinse cycles, ensuring that dishes are cleaned effectively. You should replace this motor and pump assembly if it becomes faulty. Common causes of a bad motor and pump assembly include electrical issues, wear and tear from regular use, or blockages caused by debris or food particles. Quick Answer If your dishwasher is not cleaning dishes, has weak spray pressure, makes unusual noises, or fails to circulate water, the 5304519906 pump and motor assembly may be faulty. Replacing it restores proper wash performance and water circulation. Replaces Part Numbers Replaces OEM part number: 5304519906, 154843901, EAP12712308, AFR18422, PD00053471, AP6840161, P154792801. Compatibility This pump and motor assembly is compatible with select Frigidaire, Electrolux, Kenmore, and other compatible dishwashers. Frigidaire Dishwashers Electrolux Dishwashers Kenmore Dishwashers Always verify your appliance model number before ordering. Common Problems This Part Fixes Dishes not getting clean Weak or no water spray Dishwasher making loud or grinding noise Water not circulating during wash cycle Key Features Integrated pump and motor assembly Restores strong water circulation High-quality aftermarket replacement Reliable and durable construction Product Specifications Part Number: XP5304519906 Part Type: Dishwasher Pump and Motor Assembly Brand: XPARTCO Condition: New OEM / Aftermarket: Aftermarket Application: Dishwasher Water Circulation Troubleshooting Guide Dishes remain dirty → Weak or failed pump motor No spray action → Pump not circulating water Loud noise during wash → Motor or impeller issue When Should You Replace This Assembly? Replace this assembly if your dishwasher is not cleaning properly, lacks water pressure, or makes abnormal noises during operation. Installation Notes ⚠️ Disconnect power and water supply before installation. Access the pump and motor assembly from the bottom of the unit and install securely according to your dishwasher model. Related Parts Dishwasher Spray Arm Water Inlet Valve Drain Pump Frequently Asked Questions Will this assembly fit my dishwasher?This part fits many Frigidaire and compatible dishwashers. Always verify your model number. What does a pump and motor assembly do?It circulates water through the dishwasher to clean dishes effectively. What are signs of a bad pump motor?Poor cleaning, weak spray, or loud noises during operation. Is this OEM or aftermarket?This is a high-quality aftermarket replacement part. Shop With Confidence Parts-O-Matic is a U.S.-based appliance parts retailer specializing in OEM and high-quality replacement parts. We offer fast shipping, reliable products, and expert support. Fast Shipping Quality Tested Parts Compatibility Support

Read more less

XPARTCO W10238100 Refrigerator Water Valve The XPARTCO W10238100 is an aftermarket replacement single primary water inlet valve for Whirlpool-built refrigerators sold under the Whirlpool, KitchenAid, Kenmore, Maytag, Jenn-Air, Inglis, and Ikea names. The valve is an electrically operated solenoid that opens to let water from the household supply line into the refrigerator's water system, and closes to stop it. When the valve fails, the refrigerator can stop supplying water to the dispenser and ice maker, make little or no ice, leak, or, if it no longer shuts off, overfill the ice maker and build up ice and frost. This valve is a direct replacement for the OEM W10238100 / WPW10238100 and is a simple repair for most owners, typically 15–30 minutes. Some refrigerators also use a separate dual-solenoid valve, so check the Compatibility note before ordering. Quick Answer The XPARTCO W10238100 Water Valve fixes a Whirlpool-built refrigerator with no water at the dispenser, little or no ice, an overflowing ice maker, or a leak caused by a failed water inlet valve. Single primary water inlet valve, aftermarket replacement for W10238100 and WPW10238100. Classic symptom: the dispenser gives little or no water and the ice maker isn't making ice, even though the water supply is on. Common Problems This Part Fixes Water dispenser not working, or giving only a trickle Ice maker not making ice Ice maker overflowing, with ice or frost buildup Water leaking from the refrigerator Valve making noise or not shutting off properly Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This water valve replaces the following part numbers: WPW10238100, W10238100, W10498992, IMV-8100, K-78199, AP6017532, AWP50143, EAP11750831, PD00002616, PS11750831 These are Whirlpool's un-prefixed and earlier numbers for this valve. If your old valve or parts diagram shows any of them, match against this list. Compatibility This valve is listed for refrigerators from the Whirlpool family of brands: Whirlpool, KitchenAid, Maytag, Jenn-Air, Inglis, and Ikea Kenmore, including models such as 10641162310, 10651132210, and 10651149110 Other models include ISC21CNEDS00, KRSC503ESS00, KSC24C8EYY02, and WRF560SEHZ00 Note: This is a single primary water inlet valve. Some refrigerators use a separate dual-solenoid valve for the ice maker and dispenser, which is a different part. The model list above is only a sample, so confirm fit by matching the number on your old valve or your parts diagram against the Replaces list, or contact our support team with your model number and we'll verify before you order. Key Features Aftermarket replacement single primary water inlet valve Replaces W10238100, WPW10238100, and W10498992 Restores water to the dispenser and ice maker, and proper shut-off Fits select Whirlpool, KitchenAid, Kenmore, Maytag, Jenn-Air, Inglis, and Ikea refrigerators Simple replacement, typically 15–30 minutes Product Specifications Part Number XPW10238100 OEM Part Number W10238100, WPW10238100 Part Type Refrigerator Single Primary Water Inlet Valve Condition Aftermarket Replacement Application Select Whirlpool, KitchenAid, Kenmore, Maytag, Jenn-Air, Inglis & Ikea Refrigerators Installation Notes ⚠️ Shut Off Water and Unplug Power Turn off the water supply to the refrigerator and unplug it before starting. Following your model's service guide, pull the refrigerator out and remove the rear access panel to reach the valve. Disconnect the water lines from the old valve, and the wiring connector from its solenoid, then remove the mounting screws. Install the new valve in the same position, reconnect the wiring and water lines securely, and replace the panel. Restore water and power, check every connection for leaks, and run water through the dispenser for a few minutes to flush the line. The valve needs at least 20 psi of water pressure to shut off properly, so if the ice maker still overflows, check the supply pressure. Frequently Asked Questions My dispenser has no water and the ice maker isn't working. Is this the part I need? It can be. Before replacing the valve, check that the water supply is on, the supply line isn't kinked, and the water filter isn't clogged. If those are fine, a failed water inlet valve is a likely cause. My ice maker is overflowing. Could it be the valve? Yes. A valve that doesn't shut off fully will keep letting water in. Also confirm your water pressure is at least 20 psi, since low pressure can stop the valve from closing properly. My refrigerator has a dual-solenoid valve. Will this work? No. This is a single primary valve, and the dual-solenoid valve is a different part. Check your parts diagram or contact our support team with your model number. Is this an OEM part? No. This is an XPARTCO aftermarket replacement built to match the Whirlpool W10238100. If you prefer a genuine OEM valve, contact us. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

WD26X25103 Genuine OEM GE Dishwasher Variable Wash Pump Kit The WD26X25103 is a genuine GE OEM variable wash pump kit for premium GE, Café, GE Profile, Monogram, Hotpoint, and Haier dishwashers. The wash pump is the heart of the cleaning system — it draws filtered water from the sump and drives it under pressure through the lower spray arm, the middle spray arm, and the upper wash manifold. What makes this a variable pump is its variable-speed motor: instead of running at one fixed speed, the control board modulates pump speed throughout the cycle, ramping pressure up for heavy soil and down for delicate loads, and shifting flow between spray zones. That is why a failing variable pump often produces uneven results — the bottom rack comes out clean while the top rack is barely wet. This is a complete kit, supplied with the circulation pump assembly and its integrated wiring harness, so you are not transferring connectors from the old unit. Typical failure modes include worn motor bearings that produce a loud humming or grinding during the wash portion of the cycle, a seized or debris-jammed impeller, a shaft seal that begins weeping water into the base pan and trips the flood switch, and electrical failure of the variable-speed motor windings. It directly replaces WD26X22789, AP6973120, PS12730515, and EAP12730515. This is a moderate DIY repair — most people budget 1–2 hours. Quick Answer The WD26X25103 Genuine OEM GE Variable Wash Pump Kit fixes GE, Café, GE Profile, Monogram, Hotpoint, and Haier dishwashers with dishes that come out dirty or gritty, a top rack that isn't getting wet, weak or no spray arm rotation, loud humming or grinding during the wash cycle, or water pooling in the base pan from a leaking pump seal. Variable-speed motor; kit includes pump assembly plus integrated wiring harness. Replaces WD26X22789, AP6973120, PS12730515, EAP12730515. Fits premium CDT865/CDT866, PDT845/PDT846/PDT855, and ZDT915/ZDT975 platforms — not the same pump as WD26X23258. Common Problems This Part Fixes Dishes not getting clean — food soil, grit, or film left behind after a full cycle Top rack not getting wet or not getting cleaned while the bottom rack washes normally Spray arms turning slowly or not turning at all — insufficient water pressure Loud humming, whining, or grinding noise during the wash portion of the cycle Dishwasher runs a full cycle quietly with no audible water circulation Water pooling in the base pan under the dishwasher from a leaking pump shaft seal Flood switch or leak sensor tripping and shutting the dishwasher down mid-cycle Cleaning performance that has gradually declined over months as bearings wear Pump motor humming but the impeller not turning — seized shaft or jammed impeller Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dishwasher variable wash pump kit directly replaces the following OEM and cross-reference part numbers: WD26X25103, WD26X22789, AGE25305, AP6973120, PD00054224, PS12730515, EAP12730515. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This variable wash pump kit is compatible with select premium built-in dishwashers from the following brands: GE and GE Profile dishwashers (PDT845, PDT846, and PDT855 series) Café dishwashers (CDT865 and CDT866 series) Monogram dishwashers (ZDT915 and ZDT975 series) Hotpoint dishwashers (select GE-built models) Haier dishwashers (select GE-platform models) Verified model numbers include: CDT865SSJ0SS, CDT865SSJ2SS, CDT865SMJ0DS, CDT865SMJ2DS, CDT866P2M4S1, CDT866P3M4D1, CDT866P4M4W2, PDT845SSJ0SS, PDT845SSJ2SS, PDT845SMJ0ES, PDT845SMJ2ES, PDT845SBL2TS, PDT845SBL3TS, PDT845SFL3DS, PDT846SSJ0SS, PDT846SSJ2SS, PDT846SMJ0ES, PDT846SMJ2ES, PDT855SSJ0SS, PDT855SSJ2SS, PDT855SMJ0ES, PDT855SMJ2ES, PDT855SIJ0II, PDT855SIJ2II, PDT855SBL2TS, PDT855SBL3TS, PDT855SFL3DS, ZDT915SSJ0SS, ZDT915SSJ2SS, ZDT915SIJ0II, ZDT915SIJ2II, ZDT915SPJ0SS, ZDT915SPJ2SS, ZDT975SSJ0SS, ZDT975SSJ2SS, ZDT975SIJ0II, ZDT975SIJ2II, ZDT975SPJ0SS, and ZDT975SPJ2SS. Note: GE uses several different circulation pumps across its dishwasher lineup, and they are NOT interchangeable. The WD26X25103 is the variable-speed pump used on premium CDT/PDT/ZDT platforms. It is not the same part as the WD26X23258 circulation pump (GDT695/PDT825 platforms) or the WD26X22518 pump (PDF820/GDT535/ADT521 platforms). Fitting the wrong pump can result in a physical mismatch at the sump or a harness that will not mate with your control board. Always verify your full model number — including the suffix — before ordering. Contact our support team with your model number if you're unsure. Key Features Genuine GE OEM part — factory-specified flow rate, impeller geometry, and motor control profile Variable-speed motor allows the control board to modulate wash pressure by cycle and soil level rather than running at one fixed speed Complete kit — includes the circulation pump assembly and integrated wiring harness, so no connectors need to be transferred from the old pump Drives water through the lower spray arm, middle spray arm, and upper wash manifold Resolves "dishes not clean," "top rack not getting wet," "spray arms not turning," "loud humming or grinding," and "water in the base pan" symptoms caused by pump failure Sealed shaft design protects the motor from sump water intrusion Direct drop-in replacement for the superseded WD26X22789 — no modifications required Serves GE Profile, Café, Monogram, Hotpoint, and Haier premium dishwasher platforms Replaces WD26X22789, AP6973120, PS12730515, and EAP12730515 Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number WD26X25103 Part Type Dishwasher Variable Wash Pump Kit (Circulation Pump) Condition Genuine OEM Brand GE Appliances Motor Type Variable speed Voltage 120V / 60 Hz Function Circulates water under pressure to the spray arms and upper wash manifold Kit Contents Wash pump assembly + integrated wiring harness Location Underneath the tub, mounted to the sump housing Connections 2 hose clamps + 2 electrical connections Supersedes WD26X22789 Repair Difficulty Moderate — 1 to 2 hours Quantity 1 pump kit Compatible Brands GE, GE Profile, Café, Monogram, Hotpoint, Haier Installation Notes ⚠️ Disconnect Power And Shut Off Water Before Starting Turn off the dishwasher's circuit breaker and close the hot water supply valve under the sink before beginning. Wear work gloves — the tub edges and undercarriage brackets are sharp. Before condemning the pump, run a quick check: remove the lower spray arm and filter assembly, clear any glass chips, seeds, or labels from the sump, and confirm the spray arm ports are not blocked. A clogged filter screen produces the same "dishes not clean" complaint as a failing pump and costs nothing to rule out. To replace the pump, first remove the two screws securing the dishwasher to the underside of the countertop (or to the adjacent cabinets), disconnect the water line and drain hose, and slide the unit out. Most technicians then lay the dishwasher on its front or on its back to reach the pump — put a towel down to protect the door and finish. Photograph the hose routing and wiring before disconnecting anything. Release the two hose clamps and separate the two electrical connections, then unlock the pump from the sump housing — it typically twists to release from a bayonet-style mount — and lift it out. Inspect the sump gasket and seat while the pump is off; replace the gasket if it is hardened, flattened, or nicked. Install the new WD26X25103 in the same orientation, twist to lock, reattach both hoses with their clamps, and reconnect the harness. Reinstall the dishwasher, restore water and power, then run a full cycle and check underneath for leaks before pushing the unit all the way back and reattaching the mounting screws. Tools needed: Phillips screwdriver, nut driver, pliers or hose clamp pliers, towel, work gloves. Frequently Asked Questions My top rack isn't getting clean but the bottom rack is fine. Is that the wash pump? It's the signature symptom of a weakening wash pump, yes — but check two cheaper things first. The upper wash manifold and the middle spray arm are fed last and at the lowest pressure, so they are the first zones to suffer when pump output drops. However, a clogged filter screen or a spray arm with blocked ports will starve the upper rack the same way. Pull the lower spray arm and filter, rinse them under hot water, poke a toothpick through any blocked spray ports, and run a cycle. If the top rack is still dry or dirty after that, the variable pump is losing pressure and should be replaced. What does "variable" mean on this pump, and does it matter? It matters a great deal. A variable-speed pump lets the control board change pump speed during the cycle — higher pressure for heavy soil, lower for delicate loads, and different speeds when directing flow to different spray zones. A fixed-speed pump cannot do that. This is why you cannot substitute a standard circulation pump from another GE platform even if it physically resembles this one: the control board expects a variable-speed motor and will not drive a fixed-speed unit correctly. The dishwasher is making a loud grinding noise. Do I need the whole pump? Not always — check for foreign objects first. Glass chips, fruit pits, bones, and hard plastic bits routinely get past the filter and rattle inside the pump housing or wedge against the impeller. Remove the filter assembly and inspect the sump thoroughly with a flashlight. If the sump is clean and the noise is a steady hum or grind that rises with the wash cycle, the pump's motor bearings are worn and the complete kit is the correct repair. Bearing noise does not improve on its own and usually precedes a shaft seal leak. I found water in the pan underneath the dishwasher. Could the pump cause that? Yes. When the pump's shaft seal wears out, it weeps water down onto the base pan during every wash cycle. GE dishwashers have a flood switch in that pan, so the machine will eventually detect the water and shut itself down mid-cycle or refuse to start. Before ordering, confirm the water is coming from the pump and not from a loose hose clamp, a cracked sump, or the door gasket — dry the pan completely, run a short cycle, and watch where the first drops appear. Does this kit include everything, or do I need to reuse parts from the old pump? The kit ships with the wash pump assembly and its integrated wiring harness, so you will not need to cut, splice, or transfer the electrical connector from your old pump. You will reuse your existing hoses and clamps. Inspect the sump gasket while the pump is out and replace it if it looks hardened, flattened, or nicked — a tired gasket is a common cause of a "new pump that still leaks." What's the difference between WD26X25103 and WD26X22789? They are the same pump across production revisions. WD26X22789 was the earlier number and WD26X25103 is the current GE part number that supersedes it. If your dishwasher's parts diagram shows WD26X22789, this listing is the correct replacement — order it with confidence. The additional cross-references (AP6973120, PS12730515, EAP12730515) are catalog identifiers used by various parts distributors for the same kit. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by GE to factory specifications — guaranteed fit, materials, and performance. It matches the original variable-speed motor profile, impeller geometry, flow rate, sump mounting interface, and harness connector of the pump originally installed in your dishwasher, which is important on this platform because the control board is calibrated to drive a variable-speed pump. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

WD19X25278 Dishwasher Genuine OEM Diverter Assembly Replaces Part Numbers: WD19X25278, WD18X21678, 4922277, WD00X25260, AP6871922, PS12710077. Description: This Diverter Valve Assembly Kit serves a Genuine OEM replacement Part for specific GE dishwasher models. Its key function is to provide an alternative passage for water to reach the upper spray arms of the dishwasher. A faulty or damaged diverter valve often manifests as water leaks within the dishwasher. When such leaks occur and can be traced back to the diverter valve, this assembly kit offers a comprehensive solution. It includes all necessary components and fasteners to efficiently replace the valve. This kit is suitable for use with specific General Electric dishwasher models.

Read more less

XPARTCO 5304528029 Washer Water Valve Dispenser Valve Gaskets are Not Included Washer water inlet valve. 5 Solenoid Coils, 5 Outlets Fits Specific Electrolux, Frigidaire front load washer models. Replaces Part Numbers:5304528029, 5304514790, 5304522534, AP7014477, PS16544354. Description: This Water Valve is a replacement part for specific Electrolux, Frigidaire washing machine models. This part controls the entry of water into the washer during the wash and rinse cycles. Common causes of a bad valve include mineral deposits from hard water, electrical issues, or general wear and tear over time.   This is an aftermarket part that can be used as a replacement for the OEM part.

Read more less

XPARTCO WH08X37938 Washer Lid Switch Assembly The XPARTCO WH08X37938 is an aftermarket replacement lid switch (lid lock) assembly for GE and Hotpoint top-load washers, also used on select Kenmore models. The assembly locks the lid while the washer is running and releases it when the cycle ends, and it tells the control board the lid is closed and it's safe to run. When it wears out, cracks, or fails electrically, the washer may refuse to start, stop in the middle of a cycle, show a lid or door lock error, or fail to lock the lid at all. This assembly replaces the original lock and switch as a unit, so you do not have to diagnose which internal contact has failed. It mounts on the washer cabinet with an electrical connector and is a straightforward repair, usually done in under an hour. Quick Answer The XPARTCO WH08X37938 Lid Switch Assembly fixes a GE or Hotpoint top-load washer that won't start, stops mid-cycle, won't lock the lid, or shows a lid or door lock error because the lid lock is worn or has failed. Complete replacement lock and switch assembly, aftermarket. Classic symptom: you close the lid and nothing happens, or the washer starts then stops and signals a lid or lock fault. Common Problems This Part Fixes Washer won't start when the lid is closed Washer stops partway through the wash, rinse, or spin Lid will not lock, or stays locked after the cycle ends Lid or door lock error codes Loose, cracked, or visibly damaged lid lock Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This lid switch assembly replaces the following part numbers: WH08X37938, WH08X32697, WH02X24399, WH08X32657, WH01X26694, WH01X24112, WH01X24114, WH01X26114, WH01X27954, WH08X31577, WH08X31222, 290D1580P001, 290D1580P002, 290D1580P003, 290D1580P004, 290D3070P001, EG-380843 M, AGE26076, AP7225583, EAP17626546, PD00087323, PS17626546 These are earlier GE numbers for the lid lock, as the part was updated over time. If your old lock or parts diagram shows any of them, match against this list. Compatibility This assembly is listed for select top-load washers from: GE and Hotpoint, including GTUN275EM0WW, GTUN275GM0WW, GTUP240EM0WW, and GTUP240EM2WW Kenmore, including 363.71542211, 363.71542310, and 363.71542410 Note: The model list above is only a sample, and lid locks differ between GE washer generations. Confirm fit by matching the number on your old lock or your parts diagram against the Replaces list, or contact our support team with your model number and we'll verify before you order. This part is for top-load washers. Key Features Aftermarket replacement lid switch (lid lock) assembly Replaces the lock and switch as a unit, with no need to find the failed contact Restores starting, locking, and unlocking at the end of the cycle Cross-references to WH08X32697, WH08X31577, and other earlier GE numbers Fits select GE, Hotpoint, and Kenmore top-load washers Mounts on the cabinet with a plug-in electrical connector Product Specifications Part Number XPWH08X37938 OEM Part Number WH08X37938 Part Type Washer Lid Switch (Lid Lock) Assembly Condition Aftermarket Replacement Application Select GE, Hotpoint & Kenmore Top-Load Washers Installation Notes ⚠️ Unplug Power and Shut Off Water Unplug the washer and turn off the water supply before starting. Work gloves are recommended. Open the lid and, following your model's service guide, remove the top panel or cabinet section to reach the lid lock mounted on the cabinet. Note the position of the old assembly, disconnect its wiring connector, and remove the screws holding it in place. Fit the new assembly in the same position, secure it, and reconnect the connector. Reassemble the washer, restore power and water, and run a short cycle to confirm the lid locks, the washer starts, and the lid releases at the end. Frequently Asked Questions My washer won't start with the lid closed. Is this the part I need? A failed lid lock is a common cause. The control board won't start a cycle unless it sees the lid is closed and locked. Check that the lid closes fully and that nothing is blocking it. If it still won't start, the lid lock is a likely cause. Is a lid switch the same as a lid lock? On these washers, the lid switch and lock are combined in one assembly, which this part replaces. My old part is marked WH08X32697 or WH08X31577. Will this work? Those numbers are on the Replaces list. Compare the connector and mounting against your old part, or contact our support team with your model number and we'll confirm. Will this fit my front-load washer? No. This is for top-load washers. Is this an OEM part? No. This is an XPARTCO aftermarket replacement built to match the GE WH08X37938. If you prefer a genuine OEM assembly, contact us. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

WR49X25197 Refrigerator Genuine OEM Axial Evaporator Motor Replaces WR60X26866 The WR49X25197 is a genuine GE OEM axial evaporator fan motor for the fresh food evaporator on select GE French door refrigerators. Unlike a standard evaporator fan motor, this is an axial-design motor purpose-built for the fresh food side of the refrigeration system, using its blade geometry to move air efficiently and quietly through that compartment's evaporator coil for precise, consistent temperature control. Rated 13.6VDC, 0.16A. Manufactured by Nidec, designation V80E14MS2A3-57A611. Over time, motor bearings wear out or the motor can fail electrically, and symptoms typically include the fresh food compartment running warm while the freezer remains unaffected, unusual noise from the fresh food evaporator area, or inconsistent cooling in that compartment specifically, since this motor doesn't serve the freezer side at all. It directly replaces WR60X26866, WR60X10341, WR60X24303, WR60X26033, WR60X10356, WR60X10357, WR60X26030, 239D1412P001, 239D1412P006, and AP6278228. Quick Answer The WR49X25197 Genuine OEM GE Axial Evaporator Motor fixes GE French door refrigerators where the fresh food compartment specifically runs warm, there's unusual noise from the fresh food evaporator area, or fresh food cooling is inconsistent while the freezer works fine. 13.6VDC, 0.16A axial motor. Replaces WR60X26866, WR60X10341, WR60X24303, WR60X26033, WR60X10356, WR60X10357, WR60X26030, 239D1412P001, 239D1412P006, AP6278228. If your refrigerator was manufactured between May 2014 and March 2015 (serial range HD–FF), the control software must also be updated by factory service or a Software Update Module (WR98R882802) for this motor to perform correctly. Common Problems This Part Fixes Fresh food compartment running warm while the freezer stays normal Unusual noise coming from the fresh food evaporator area Inconsistent or fluctuating temperature in the fresh food section specifically Fresh food evaporator fan not spinning or spinning intermittently Reduced airflow affecting fresh food cooling performance Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This refrigerator axial evaporator motor directly replaces the following OEM and cross-reference part numbers: WR49X25197, WR60X26866, WR02X13733, WR60X10341, WR60X10356, WR60X10357, WR60X24303, WR60X26030, WR60X26033, V80E14MS2A3-57A611, 8817V W1, 239D1412P006, PD00038765, FIX12172983, AGE29673, AP6278228, PS12172983 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This axial evaporator motor is compatible with select GE French door refrigerators. Note — fresh food evaporator only, and a software caveat for certain units: This motor serves the fresh food evaporator specifically — a different application from a general freezer evaporator fan motor. Additionally, if your refrigerator was manufactured between May 2014 and March 2015 (serial range HD through FF), the refrigerator's control software must be updated by factory service, or with a Software Update Module (WR98R882802), for this motor to perform correctly after installation. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Genuine GE OEM part — factory-specified axial blade design for the fresh food evaporator Resolves "fresh food running warm," "unusual noise from the fresh food evaporator," and "inconsistent fresh food cooling" symptoms Rated 13.6VDC, 0.16A Manufactured by Nidec, designation V80E14MS2A3-57A611 Direct drop-in replacement matching the original mounting and blade fitment Replaces WR60X26866, WR60X10341, WR60X24303, WR60X26033, WR60X10356, WR60X10357, WR60X26030, 239D1412P001, 239D1412P006, and AP6278228 Compatible with GE French door refrigerators Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number WR49X25197 OEM Part Number WR60X26866 Part Type Axial Evaporator Fan Motor (Fresh Food) Condition Genuine OEM Brand GE Application French Door Refrigerators — Fresh Food Evaporator Voltage 13.6VDC Amperage 0.16A Motor Manufacturer Nidec (V80E14MS2A3-57A611) Motor Type Axial Software Update Caveat Required for units mfg. May 2014–March 2015, serial range HD–FF (WR98R882802) Quantity 1 evaporator motor Compatible Brand GE Installation Notes ⚠️ Unplug Refrigerator Before Starting — Check Your Manufacture Date For A Software Update Requirement Disconnect power at the outlet before beginning, and move perishable food to a cooler for the duration of the repair. Wear work gloves. Before starting, check your refrigerator's serial number/manufacture date sticker (typically inside the fresh food compartment) — if your unit was made between May 2014 and March 2015 with a serial range of HD through FF, plan for a control software update via factory service or a Software Update Module (WR98R882802) after installing this motor, since without it the new motor may not perform correctly. Access to the fresh food evaporator is typically through an interior panel in the fresh food compartment, separate from the freezer's evaporator access — check your model's service diagram. If there's frost or ice buildup around the fan or coil, let the unit sit unplugged with the door open for a few hours before continuing. Photograph the wiring harness connector and the fan blade's orientation before disconnecting anything. Unplug the wiring harness connector from the old motor, remove the mounting screws or clips holding the motor bracket in place, and pull the motor and fan blade assembly free. Mount the new WR49X25197 in the same position, reconnect the wiring harness connector fully, and confirm the blade spins freely by hand without contacting the housing before reassembling the panel. Restore power and monitor the fresh food compartment over the next 24 hours to confirm even, consistent cooling has returned. Tools needed: Phillips screwdriver, work gloves. Frequently Asked Questions My fresh food section runs warm but the freezer is fine. Is this the right part? Yes, this is exactly the symptom pattern this motor addresses, since it's dedicated specifically to the fresh food evaporator rather than serving both compartments. If your freezer is cooling normally and only the fresh food section is warm or inconsistent, this axial motor is a strong candidate for the cause. Do I really need a software update after installing this motor? Only if your refrigerator falls into a specific manufacturing window: units made between May 2014 and March 2015, identifiable by a serial range of HD through FF. For those units, GE's own guidance states the control software must be updated by factory service or with a Software Update Module (WR98R882802) for the new motor to perform correctly. If your refrigerator falls outside that date range, this step isn't necessary — check your serial number sticker to confirm which category your unit falls into. Is this the same as a regular evaporator fan motor? Not quite — this is an axial-design motor built specifically for the fresh food evaporator on GE French door refrigerators, distinct from general evaporator fan motors that serve the freezer side or both compartments together. Always confirm your model number and which compartment's fan has failed before ordering. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by GE to factory specifications — guaranteed fit, materials, and performance. It matches the original axial motor design, blade fitment, and electrical rating of the fresh food evaporator motor originally installed in your refrigerator. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

W10757833 Dishwasher Control Panel Fits specific KitchenAid dishwasher models. Replaces Part Numbers: W10757833, 8531268, 3452787, 8531265, 8531537, 8564487, 8564565, AP5956414, PS10064580. Description: This Rack Adjuster is a Genuine OEM part for Whirlpool dishwashers, designed to allow for the easy adjustment of the dishwasher rack's height. This feature accommodates dishes of various sizes. By providing the flexibility to adjust the rack height, this part enhances the dishwasher's adaptability to different washing needs.

Read more less

WD26X25104 Dishwasher Genuine OEM Drain Pump Fits Specific GE Dishwasher Models.  Replaces Part Numbers: WD26X25104, WD26X22810, WD26X20306, AP6990087, PS16217045 Description: The Variable Drain Pump Kit is a Genuine OEM replacement part for select GE built-in dishwasher models. It includes both the drain pump and clamps needed to remove water from the dishwasher during cycles. Common causes are blockages in the drain hose inhibiting water outflow or failure of the electric pump motor components over extended use.

Read more less

XPARTCO W11266654 Washer Door Boot Outer Clamp Description: The Outer Door Boot Seal Clamp Washer is a replacement part specific to Whirlpool-brand washing machines. Multiple washers are used behind the outer boot seal clamp to create a uniform, compressed seal around the washer door opening.  Replaces Part Number: W11266654, W10237503, WPW10237503, 4894886, AP6809210, PS12584490, W10818945.    

Read more less