Search results for "dryer belts"

XP53-0771 Dryer Thermostat This thermostat has a limit of 248°F. It will turn the heating element back on when the temperature drops by 80°F. Fits Maytag, Admiral, Norge Electric Dryers Replaces Part Numbers:WP53-0771, 53-0771, 53-0306, 53-1037, 53-1459, ER53-0771, OEM18028919, AP6009638, PS11742806, SET176, TJSET176.   This is an aftermarket part that can be used as a replacement for the OEM part. California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

XPARTCO W10820036 Washer / Dryer Door Switch The XPARTCO W10820036 is an aftermarket replacement door switch used on select Whirlpool-built combination washer/dryer units. This switch is a safety interlock: it detects whether the door is fully closed and latched, and it signals the control board that it is safe to run the motor, heater, and water valves. On a combo unit, this single interlock typically governs both the wash and dry portions of the cycle, since both functions share the same drum and door. If the switch fails to detect a closed door — or fails electrically even when the door is closed properly — the control will refuse to start the cycle, or will stop mid-cycle if the switch drops out while running. Typical failure modes for a part like this include a cracked or worn switch lever that no longer depresses fully when the door closes, internal contacts that have pitted or burned out from years of cycling, and a housing that has come loose from its mounting bracket so the plunger no longer lines up with the door strike. A functioning door switch should click firmly when the door closes and should show continuity across its terminals only when the lever is pressed. Quick Answer The XPARTCO W10820036 Washer/Dryer Door Switch is a door safety interlock switch for select Whirlpool-built combination washer/dryer units. It fixes units that won't start with the door closed, stop mid-cycle, or fail to register the door as closed even when it's latched properly. Note: this listing was built from general parts knowledge because current supplier and cross-reference data was not available at build time — see the note below before publishing. Common Problems This Part Fixes Washer/dryer combo won't start even though the door is fully closed Cycle stops partway through, as if the door had been opened Door doesn't feel like it's "clicking" or latching the way it used to Console shows a door-related error or won't advance past the door-closed step Intermittent operation — sometimes starts, sometimes doesn't, depending on how the door is closed Visibly cracked, loose, or broken switch housing or lever Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This door switch directly replaces the following OEM part number: W10820036, 279347, 2-2770, 2-50062, 2-5415, 2020, 202770, 233480, 235462, 237194, 238775, 238980, 239868, 24198, 247207, 26000279347, 279290, 287219, 287220, 291679, 291697, 292212, 296141, 296144, 3347287, 338883, 3392266, 3397503, 3399991, 347207, 350526, 359230, 359484, 364090, 364091, 367034, 388322, 389105, 4273196, 4319330, 660308, 687429, 75958, 8224, 83333, 84144, 86628, 89556, 99788, 99838, LP210, AP5985146, AWP41434, EAP334185, PD00023982, PS11723153. No additional cross-reference numbers have been confirmed for this part yet. If you have a superseded or alternate number for your appliance, contact our support team and we will verify compatibility before you order. Compatibility This door switch is intended for select Whirlpool-built washer/dryer combination units, where a single door and drum serve both the wash and dry functions. Model list not yet confirmed: A specific compatible model list for W10820036 was not available at the time this page was built. Please verify your exact model number before ordering. Contact our support team with your model number and we will confirm fitment before you purchase. Key Features Aftermarket replacement door safety switch for Whirlpool-built washer/dryer combo units Detects whether the door is closed and latched before allowing the wash or dry cycle to run Resolves "won't start with door closed," "stops mid-cycle," and "door not detected" symptoms Direct drop-in replacement for the original W10820036 switch — no modification required Aftermarket replacement built to OEM-equivalent quality standards Product Specifications Part Number XPW10820036 OEM Part Number W10820036 Part Type Washer/Dryer Combo Door Safety Switch Condition Aftermarket Replacement Application Whirlpool-Built Washer/Dryer Combination Units Function Door-closed safety interlock for wash and dry cycles Quantity 1 switch Compatible Brand Whirlpool (combo platform) Installation Notes ⚠️ Unplug The Unit Before Starting Disconnect power at the outlet or shut off the circuit breaker before beginning. Wear work gloves. Access to the door switch on combo units is typically through the front or top control panel — photograph the wiring harness before disconnecting it so you can match it exactly on reassembly. Confirm the new switch's lever aligns with the door strike before securing the mounting screws, and test for a firm, positive click when the door closes before restoring power and running a cycle. If your unit's service manual is available, follow its specific access and mounting steps rather than relying solely on general guidance. Frequently Asked Questions My combo unit won't start. Is this definitely the door switch? It's one of the most common causes when a unit refuses to start with the door visibly closed. Before replacing the switch, confirm the door is latching fully and that nothing (a stray sock, a bent strike bracket) is preventing it from closing all the way. If the door latches firmly but the unit still won't start, or a multimeter shows no continuity across the switch terminals when the lever is pressed, the switch itself is the likely culprit. Does this switch control both the washer and dryer functions? On combination washer/dryer units, yes — a single door and drum typically serve both functions, so one door switch acts as the safety interlock for both the wash and dry portions of the cycle. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured to match the mounting, switching function, and door-interlock behavior of the original W10820036 switch used in compatible combination washer/dryer units. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO 8557403 Dryer High-Limit Thermostat with Thermistor Replaces WP8557403 The XPARTCO 8557403 is an aftermarket replacement dryer high-limit thermostat and thermistor sensor assembly compatible with a wide range of Whirlpool, Maytag, Kenmore, Amana, KitchenAid, Jenn-Air, Roper, Admiral, Norge, and Magic Chef electric dryers — including the Whirlpool Duet and Maytag MED series. This single component combines two functions: the high-limit thermostat (rated L146-44C, opens at 295°F) acts as a resettable safety switch that cuts power to the heating element if the dryer air temperature exceeds safe limits, and the integrated 50-ohm thermistor continuously monitors air temperature and sends resistance-based readings to the control board to regulate the drying cycle. When this part fails — whether the thermostat opens permanently or the thermistor provides incorrect temperature data — the dryer may produce no heat, run too hot, take too long to dry, overheat, or display temperature-related error codes. It measures 1-5/8"L x 1-5/8"W x 2"H with approximately 1-5/8" between mounting holes and is constructed from black/gray plastic and metal. It directly replaces WP8557403, 1180102, AP6013164, EAP11746386, PD00003588, and PS11746386. Note: the exhaust duct thermostat and thermal fuse are separate parts — if those have also failed, they must be ordered separately. Installs in 15–20 minutes with basic hand tools. Quick Answer The XPARTCO 8557403 Dryer High-Limit Thermostat with Thermistor fixes Whirlpool Duet, Maytag MED, and related dryers with no heat, overheating, or erratic temperature. Combined part: L146-44C high-limit thermostat (opens at 295°F, auto-resets) + 50-ohm NTC thermistor. 1-5/8"L x 1-5/8"W x 2"H, ~1-5/8" between mounting holes. Replaces WP8557403, 1180102, AP6013164, EAP11746386, PD00003588, PS11746386. For Whirlpool, Maytag, Kenmore, Amana, KitchenAid, Jenn-Air, Roper, and Admiral electric dryers. Common Problems This Part Fixes Dryer produces no heat — high-limit thermostat has failed open Dryer overheating — thermostat not opening at the correct temperature Dryer takes too long to dry — thermistor providing incorrect temperature readings to the control board Dryer cycling on and off erratically — thermistor fault causing incorrect cycle control Temperature-related error codes on models with digital displays Multimeter test shows open circuit on the thermostat at room temperature Multimeter test shows open or shorted thermistor (not ~50 ohms at room temperature) Replaces Part Numbers This thermostat/thermistor assembly directly replaces the following OEM and cross-reference part numbers: WP8557403, 8557403, 1180102, AP6013164, AWP48681, EAP11746386, PD00003588, PS11746386. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This high-limit thermostat and thermistor is compatible with select electric dryers only from the following brands: Whirlpool electric dryers — Duet, WED5000, WED5500, WED5600, WED5620, WED8000, WED8200, WED8500, WED9200, WED92HEF, WED7000 series and related models Maytag electric dryers — MED3500, MED5630, MED6630, MED7230, MEDB835 series and related models Kenmore / Sears electric dryers — 110-series (Whirlpool-built models) Amana electric dryers (select models) KitchenAid electric dryers (select models) Jenn-Air electric dryers (select models) Roper electric dryers Admiral electric dryers Norge electric dryers Magic Chef electric dryers Note: This part is for electric dryers only. The exhaust duct thermal fuse and cycling thermostat are separate parts — if those have also failed, they must be ordered separately. Always verify your model number before ordering. Key Features Combined high-limit thermostat and thermistor in a single assembly — replaces both functions in one part High-limit thermostat rated L146-44C — opens at 295°F (146°C), resets automatically when cooled Integrated 50-ohm NTC thermistor — continuously monitors dryer air temperature and sends readings to the control board for cycle regulation Dimensions: 1-5/8"L x 1-5/8"W x 2"H; approx. 1-5/8" between mounting holes Black/gray plastic and metal construction Electric dryers only — not for gas dryer models Replaces WP8557403, 1180102, AP6013164, EAP11746386, PD00003588, and PS11746386 Compatible with Whirlpool Duet, Maytag MED, Kenmore, Amana, KitchenAid, Jenn-Air, Roper, Admiral, Norge, and Magic Chef electric dryers Aftermarket replacement built to OEM-equivalent quality standards Quick DIY repair — installs in 15–20 minutes with basic hand tools Product Specifications Part Number 8557403 OEM Part Number WP8557403 Part Type Dryer High-Limit Thermostat with Integrated Thermistor Sensor Condition Aftermarket Replacement Application Electric Dryers Only Thermostat Rating L146-44C — opens at 295°F (146°C), auto-resets Thermistor 50-ohm NTC (at room temperature ~25°C) Dimensions 1-5/8"L x 1-5/8"W x 2"H Mounting Hole Spacing Approx. 1-5/8" center to center Color Black / Gray Material Plastic / Metal Compatible Brands Whirlpool, Maytag, Kenmore, Amana, KitchenAid, Jenn-Air, Roper, Admiral, Norge, Magic Chef Installation Notes ⚠️ Unplug Dryer Before Starting — Electric Dryers Only Disconnect power before beginning. The 8557403 thermostat/thermistor assembly is typically located on the heating element housing or duct inside the dryer — access it by removing the back panel. On Whirlpool Duet and Maytag front-load-style dryers, the component may be accessible by removing the lower front panel. Photograph all wire connections before disconnecting — the thermistor wires and thermostat wires must be reconnected to the correct terminals. Remove the two mounting screws and pull the old assembly off. Note the position and orientation before removing. Install the new 8557403 assembly in the same position and orientation, reconnect all wires, and reinstall the mounting screws and panel. Restore power and run a test heat cycle to confirm normal operation. Tools needed: Phillips screwdriver, 1/4" nut driver. Frequently Asked Questions What makes this part unusual — why does it combine a thermostat and a thermistor? The WP8557403 is a combined assembly used on newer Whirlpool Duet and Maytag MED series dryers that use electronic temperature control rather than purely mechanical thermostats. The high-limit thermostat (L146-44C) provides the traditional safety function — it opens the circuit if dryer temperature exceeds 295°F. The integrated NTC thermistor continuously reports resistance-based temperature data to the electronic control board, which uses the data to regulate the heating element and control cycle timing. Both functions are built into a single compact housing, making this a unique part that replaces what older dryers used to handle with separate components. How do I test the thermostat and thermistor? Set your multimeter to continuity or resistance mode. For the thermostat portion: probe the thermostat terminals — at room temperature, a working thermostat shows closed continuity (near-zero resistance). An open circuit at room temperature confirms the thermostat has failed. For the thermistor portion: probe the thermistor terminals — at room temperature (approximately 25°C/77°F), a working 50-ohm NTC thermistor should read approximately 50 ohms. A reading of zero ohms (shorted) or open circuit (no continuity) confirms the thermistor has failed. Either failure mode warrants replacing the complete 8557403 assembly. What is the difference between 8557403 and WP8557403? These are the same part. WP8557403 is the updated Whirlpool OEM part number that superseded the original 8557403. The 1180102 is also a cross-reference for this same assembly. This aftermarket replacement is compatible with all of these numbers. Do I also need to replace the thermal fuse or cycling thermostat? The 8557403 replaces the high-limit thermostat and thermistor mounted on the heating element housing area. The exhaust duct thermal fuse (WP3392519 on most Whirlpool-family dryers) and cycling thermostat (WP3387134) are separate components located on the exhaust duct and are not included in or replaced by the 8557403. If your dryer has no heat, test all thermal components before ordering — check the 8557403 assembly, the thermal fuse, and the cycling thermostat, then order only what has failed. If an overheating event caused the high-limit to fail, the other thermal components may be stressed as well. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured from plastic and metal with an L146-44C thermostat and 50-ohm NTC thermistor to match the specifications and performance of the original WP8557403 assembly. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO W10900067 Dryer Thermal Cut-Off Fuse & Thermostat Kit – Compatible with Whirlpool, Maytag & Kenmore Dryers Product Description Restore safe and reliable dryer heating with the XPARTCO W10900067 Dryer Thermal Cut-Off Fuse & Thermostat Kit. This cut-off terminal is a replacement Part for specific Kenmore, Maytag, Roper, Whirlpool dryer models. The kit contains a 309°F Thermal Cut-Off Fuse and a high limit thermostat. In electric dryers, it shuts off the heat if overheating occurs to prevent fire risk. The thermal fuse cuts power while the thermostat regulates the operating temperature. To install, first, unplug the dryer. Use a multimeter to test the old fuse for continuity at room temperature; it should read zero ohms. XPARTCO is a trusted aftermarket brand offering appliance replacement parts built to OEM-equivalent specifications at a cost-effective price. Replaces Part Numbers W10900067, 4460718, N197, 197CM, 197, PD00046493, EAP11769432, AP6036100, PS11769432. Compatibility This replacement dryer thermal cut-off fuse and thermostat kit fits select Whirlpool, Maytag, Kenmore, Amana, Estate, Roper, and Crosley electric dryers. Example compatible models include (but are not limited to): Whirlpool WED4800XQ, WED4815EW1 Maytag MEDC215EW1 Kenmore 110.6012010 Always verify your dryer’s model number before ordering.Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement Kit – Matches OEM temperature and safety specifications 🌡️ Accurate Heat Protection – Helps regulate dryer temperature safely 🔥 Overheat Safety Cut-Off – Prevents damage caused by excessive heat 💰 Cost-Effective Repair – Reliable alternative to higher-priced OEM kits 🛡️ Fixes Common Issues – Resolves no heat, overheating, and thermal shutdowns 📐 Product Specification Part Number: W10900067 Component Type: Dryer Thermal Cut-Off Fuse & Thermostat Kit Includes: Thermal cut-off fuse and high-limit thermostat Application: Heater housing / exhaust temperature control Material: Heat-resistant metal housings Mounting: Screw-mounted Quality Level: Aftermarket replacement (not OEM) 🛠️ Installation Notes Tools Needed: Phillips screwdriver, nut driver ⚠️ Safety First: Always unplug the dryer before servicing to avoid electrical shock. Basic Steps: Disconnect dryer power. Remove the rear access panel. Locate the thermal cut-off and thermostat on the heater housing. Disconnect wiring and remove old components. Install the new XPARTCO W10900067 components in the same positions. Reconnect wiring, reinstall panel, and restore power. Run a test cycle to confirm proper heating. ⏱️ Time Required: 20–30 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Aftermarket Appliance Parts 🔄 30-Day Return Policy Restore safe dryer heating and protection — Add to Cart Now for a dependable, budget-friendly repair!

Read more less

XPARTCO WE03X10008 Dryer Drum Roller Replaces Part Numbers:WE03X10008, 1088999, AH959905, EA959905, AP3778075, PS959905.   This is an aftermarket part that can be used as a replacement for the OEM part. California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

XPARTCO 35001092 – 35001193 Dryer Thermostat Set – Replaces WP35001092, WP35001193 – Compatible with Whirlpool, Maytag & Kenmore Dryers Product Description Restore proper dryer temperature control and safety with the XPARTCO 35001092 – 35001193 Dryer Thermostat Set. This high-quality aftermarket kit includes the operating thermostat and thermal cut-off, designed to regulate heat and protect the dryer from overheating. Failed thermostats can cause no heat, overheating, long dry times, or repeated thermal fuse blowouts. Replacing both components together ensures accurate temperature cycling and safe, reliable dryer operation. Replaces Part Numbers WP35001092, 35001092, 1122485, PD00004704, EAP11741822, AP6008682, PS11741822.  WP35001193, 35001193, 1185515, PD00003365, EAP11741829, AP6008689, PS11741829.  Compatibility This replacement dryer thermostat set fits select Whirlpool, Maytag, Kenmore, Amana, Crosley, and Estate electric dryers. Example compatible models include (but are not limited to):Whirlpool WED4815EW1Maytag MEDC215EW1Kenmore 110.65132411 Always verify your dryer’s model number before ordering.Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement Set – Matches OEM heat regulation and safety performance 🌡️ Accurate Temperature Control – Maintains proper drying temperatures 🔥 Overheat Protection – Thermal cut-off prevents unsafe temperature conditions 💰 Cost-Effective Repair – Reliable alternative to OEM thermostat kits 🛡️ Fixes Common Issues – Solves no heat, overheating, long dry times, or blown fuses 📐 Product Specification Part Numbers: 35001092, 35001193 Component Type: Dryer Operating Thermostat & Thermal Cut-Off Set Application: Heater housing / exhaust temperature regulation Material: Heat-resistant metal thermostat bodies Mounting: Screw-mounted Compliance: Built to OEM-equivalent quality standards (not OEM) 🛠️ Installation Notes Tools Needed: Phillips screwdriver, nut driver ⚠️ Safety First: Always unplug the dryer before servicing to avoid electrical shock. Steps: Disconnect dryer power and remove the rear access panel. Locate the thermostat and thermal cut-off on the heater housing. Disconnect wiring and remove old components. Install the new XPARTCO 35001092 & 35001193 parts in the same positions. Reconnect wiring, reinstall the panel, and restore power. Run a test cycle to confirm proper heating and cycling. ⏱️ Time Required: 15–20 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Appliance Parts Supplier 🔄 30-Day Return Policy Restore proper dryer heat control and safety — Add to Cart Now for a dependable, budget-friendly repair!

Read more less

XPARTCO WE03X37317 - WE03X37318 Dryer Drum Glide Set - Compatible with GE, Hotpoint. Product Description Restore your dryer’s smooth operation with the WE03X37317 - WE03X37318 Dryer Drum Glide Set from XPARTCO. This replacement set includes four drum slides to support the front of the dryer drum, ensuring smooth rotation. Designed for GE, Hotpoint dryers, it fixes issues like squeaking, grinding, or improper drum rotation. These slides are located on the front panel of the dryer and work to support the drum as it rotates, Slide are designed to reduce friction between the drum and the panel, ensuring smooth operation and helping to prolong the life of the appliance. Note: Includes two WE03X37318 and two WE03X37317 slides.  WE03X37317 Replaces Part Numbers: WE03X37317, WE1M1067, WE01M0316, WE03X37317-50PK, WE1M1067-100PK, WE1M316, WE1M481, WE1M507, AP5668531, AP7217723, PS6447706, PS17137203. WE03X37318 Replaces Part Numbers: WE03X37318, WE1M504, WE01M0333, WE1M333, TJDE504, TJWE1M333, DE504, DE775, TJDE775, AH755842, EA755842, ERWE1M333, AP7217724, PS17137205. Compatibility: Compatible with models including but not limited to: GE: GTD42EASJWW, GTD65EBSJWS, GTD33EASKWW, GTX33EASKWW, GTD72EBPNDG Hotpoint: HTX24EASKWS, HTX21PASKWW Kenmore: 363.61542410 Verify your model number or contact our support team for assistance. Key Features: ✅ Brand Compatibility: Fits select GE, Hotpoint, and Kenmore dryer models. 🔄 Specifications: Four replacement plastic drum slides, each ~2–3" long, clip onto drum support for reliable rotation. 💰 Cost-Effective: OEM performance at a competitive price. 🛠️ Easy Installation: Requires a screwdriver, putty knife, work gloves; typically installed in 20–40 minutes. 🛡️ Reliable Fixes: Resolves squeaking, grinding, or improper drum rotation. Installation Notes: Safety First: Unplug the dryer or shut off the circuit breaker before installation to avoid electrical shock. Remove top and front panels, access drum support, remove old slides, install new slides from the set, and reassemble. Inspect drum bearing and felt seal for wear. Run a test cycle to confirm smooth operation. Shop Parts-O-Matic for high-quality replacement appliance parts with a 30-day return policy. Keep your dryer running smoothly today! Add to cart now for a budget-friendly fix!

Read more less

ERP 4560EL3001A Dryer Idler Pulley Replaces Part Numbers: 4560EL3001A, PS3523032, AP4438625    This is an aftermarket part that can be used as a replacement for the OEM part. California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

XPARTCO 35001191 Dryer Thermistor – Replaces WP35001191 – Compatible with Whirlpool, Maytag & Kenmore Dryers Product Description Maintain accurate temperature control and efficient drying with the XPARTCO 35001191 Dryer Thermistor. This Dryer Thermistor is a replacement part for specific Whirlpool, Kenmore, Maytag dryer models, that is responsible for monitoring and controlling the temperature within the dryer drum. This sensor prevents overheating or under-heating, which can affect drying performance and fabric care. The thermistor communicates temperature readings to the dryer's control board, which then adjusts the heat accordingly to maintain the desired temperature settings. Replaces Part Numbers WP35001191, 35001191, 1185513, PD00003059, EAP11741828, AP6008688, PS11741828.  Compatibility This replacement dryer thermistor fits select Whirlpool, Maytag, Kenmore, Amana, Crosley, and Estate electric dryers. Example compatible models include (but are not limited to):Whirlpool WED4815EW1, Maytag MEDC215EW1, Kenmore 110.65132411. Always verify your dryer’s model number before ordering.Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement – Matches OEM temperature-sensing accuracy 🌡️ Precise Heat Regulation – Helps control dryer temperature efficiently 🔧 Reliable Sensor Performance – Sends accurate feedback to control board 💰 Cost-Effective Repair – Quality alternative to OEM thermistors 🛡️ Fixes Common Issues – Resolves overheating, no heat, long dry times, or error codes 📐 Product Specification Part Number: 35001191 Component Type: Dryer Thermistor / Temperature Sensor Application: Exhaust temperature monitoring Material: Heat-resistant sensor body with wire leads Mounting: Screw-mounted on blower housing Compliance: Built to OEM-equivalent quality standards (not OEM) 🛠️ Installation Notes Tools Needed: Phillips screwdriver, nut driver ⚠️ Safety First: Always unplug the dryer before servicing to prevent electrical shock. Steps: Disconnect dryer power and remove the rear panel. Locate the thermistor on the blower housing. Disconnect the wiring harness and remove mounting screws. Install the new XPARTCO 35001191 thermistor. Reconnect wiring, reinstall panel, and restore power. Run a test cycle to confirm proper temperature regulation. ⏱️ Time Required: 10–15 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Appliance Parts Supplier 🔄 30-Day Return Policy Restore accurate dryer temperature control — Add to Cart Now for a dependable, budget-friendly repair!

Read more less

XPARTCO 3406108 Dryer Door Switch - Compatible with Whirlpool, Kenmore, Maytag Dryers Product Description Ensure safe and reliable operation of your dryer with the replacement XPARTCO 3406108 Dryer Door Switch. This door switch is designed for select Whirlpool, Kenmore, Maytag, and other dryer models, preventing operation when the door is open and ensuring proper start/stop functionality. It addresses issues like the dryer not starting, running with the door open, or failing to stop, offering a cost-effective alternative to OEM parts. Note: Includes one door switch with 2 wire leads and a two-prong plug. Sold individually. Disconnect power before installation. Verify compatibility with your dryer model. Replaces part numbers: WP3406108, 3406108, PD00029356, EAP11741702, PS11741702, AP6008562.  Compatibility: Compatible with models including but not limited to: Whirlpool: LTE5243DQ1 , LTE5243DQ2 , LTE5243DQ3 , LTE5243DQ4 , LTE5243DQ5 , LTE5243DQ6 , LTE5243DQ7 , LTE5243DQ8 , LTE5243DQ9 , LTE5243DQA , LTE5243DQB , LTE5243DT2 , LTE5243DT3 , LTE5243DT4 , LTE5243DT5 , LTE5243DT6 , LTE5243DT7 , LTE5243DZ1 , LTE5243DZ2 , LTG5243DQ1 , LTG5243DQ2 , LTG5243DQ3 , LTG5243DQ4 , LTG5243DQ5 , LTG5243DQ6 , LTG5243DQ7 , LTG5243DQ8 , LTG5243DQ9 , LTG5243DQA , LTG5243DQB , LTG5243DQC , LTG5243DT2 , LTG5243DT3 , LTG5243DT4 , LTG5243DT5 , LTG5243DT6 , LTG5243DT7 , LTG5243DT8 , LTG5243DZ1 , LTG5243DZ2 , WET4024EW0 , YLTE5243DQ2 , YLTE5243DQ3 , YLTE5243DQ4 , YLTE5243DQ5 , YLTE5243DQ6 , YLTE5243DQ7 , YLTE5243DQ8 , YLTE5243DQ9 , YLTE5243DQA , YLTE5243DQB , YWET4024EW0. Kenmore: 11060012000, 11060022010, 11060232000 Maytag: MEDC400VW0, AED4475TQ1 Other brands: Select models requiring 3406108 (e.g., Amana, Crosley, Roper) Verify your model number or contact our support team for assistance. Key Features: ✅ Brand and Models Compatibility: Fits select Whirlpool, Kenmore, Maytag, Amana, Crosley, and Roper dryers requiring 3406108. 🔥 Specifications: Replacement dryer door switch, 2 wire leads, two-prong plug, 120-240V, 50-60Hz, 11A, 1/3HP. 💰 Cost-Effective Alternative: Offers OEM-equivalent performance at a lower price. 🛠️ Easy Installation: Requires Phillips screwdriver, work gloves; typically installed in 5–10 minutes. 🛡️ Effective Fixes: Resolves issues like dryer not starting, running with door open, or failing to stop when door is opened. Product Specification Part Number: XP3406108 Component Type: Dryer door switch Material: Durable plastic housing with metal contacts Terminal Type: Two-prong plug with 2 wire leads Operating Conditions: Suitable for high-heat dryer environments Compliance: UL-listed components, Prop 65 warning for California Installation Notes: Safety First: Disconnect the dryer from the power source before installation. Tools Needed: Phillips screwdriver, work gloves. Process: Locate the door switch near the dryer door frame, disconnect wiring, remove the old switch, and install the new one, ensuring proper terminal connections. Shop for high-quality replacement appliance parts with a 30-day return policy. Keep your dryer running safely today! Add to cart now for a budget-friendly fix!

Read more less

XPARTCO 3387134 Dryer Cycling Thermostat - Compatible with Whirlpool, Kenmore, Maytag Product Description Ensure optimal drying performance with the XPARTCO 3387134 Dryer Cycling Thermostat. This replacement thermostat, with an internal bias heater rated L155-25, is designed as a replacement for select Whirlpool, Kenmore, Maytag, and other compatible dryers. It regulates the drum temperature to maintain efficient drying, addressing issues like overheating, insufficient heat, or prolonged drying times. If the dryer won't heat, check the thermal fuse or thermal cut-out first, as they typically fail before the cycling thermostat. Note: Includes (1) cycling thermostat. Disconnect power before installation. Verify compatibility with your dryer model. Replaces part numbers: WP3387134, 3387134, 2011, 2893, 3-6910, 306910, 3387135, 3387139, ET187, PD00002313, EAP11741405, AP6008270, PS11741405, WP3387134VP, L150-15F, L155-25F.  Compatibility: Compatible with select dryer models, including but not limited to: Whirlpool: LE5700XKW0, LE5920XKW0, WED4815EW1, WED4910XQ1, WED5300SQ0 Kenmore: 110.97591420, 110.97591220, 110.97592420, 110.60072990 Maytag: MDE5500AYW, MDE6000AYW, MDE7600AYW Roper: RED4440VQ1, REX5634KQ1 Amana: NED4655EW0 KitchenAid: KEYE760WWH0 Verify your model number or contact our support team for assistance. Key Features: ✅ Brand and Models Compatibility: Fits select Whirlpool, Kenmore, Maytag, Roper, Amana, KitchenAid, and other dryers. 🔧 Specifications: Non-OEM cycling thermostat with internal bias heater, L155-25 SPST, 120V, 2W. 💪 Reliable Performance: Regulates drum temperature for efficient drying and prevents overheating. 🛠️ Easy Installation: Requires a screwdriver and pliers; typically installed in 15–30 minutes. 🛡️ Effective Fixes: Resolves overheating, insufficient heat, or prolonged drying times. Product Specification Part Number: 3387134 Component Type: Dryer cycling thermostat Material: Plastic and metal Electrical Specs: 120V, 2W; L155-25 SPST, opens at 155°F, closes at 130°F (Based on web:3) Compliance: Prop 65 warning for California Installation Notes: Safety First: Disconnect the dryer from the power source before installation. Shop for high-quality appliance parts with a 30-day return policy. Keep your dryer running efficiently today! Add to cart now for a reliable fix!

Read more less

(2 Pack) EXP571 Dryer Door Catch Product Overview This Door Catch is a replacement part for specific Maytag, Kenmore, LG, Frigidaire, GE, Amana, Whirlpool dryer models. It includes the door catch. This part ensures the dryer door remains securely closed during operation, preventing heat loss and ensuring the appliance functions efficiently. Common causes of a bad door catch include regular wear and tear, physical damage, or misalignment of the door, which can impact the catch's ability to latch properly. Fix a loose or non-latching dryer door with this aftermarket replacement for part number EXP571. This dryer door catch holds the dryer door securely closed during operation to ensure proper airflow and drying performance. Designed to fit specific Maytag, Kenmore, LG, Frigidaire, GE, Amana, Whirlpool dryer models. ✅ Key Features: High-quality aftermarket replacement Made from durable plastic for long-lasting use Designed to securely latch the door shut Simple snap-in installation — no tools required Helps prevent cycle interruption due to door opening 🔁 Replaces OEM Part Numbers: WP71002106, WP3389441, 3389441, 71002106, AP6010685, PS11743869, AP6008299, PS11741434, WE1X1195, AP2042209, PS266896, 131658800, AP2107362, PS418433, 5307521419, 10690002, 10690001. ⚠️ Common Symptoms Fixed: Dryer door won’t stay closed Dryer won’t start due to open door switch Door pops open during a cycle Visible wear or damage to original catch 🧰 Compatible Brands: ✔️ Frigidaire✔️ Electrolux✔️ Kenmore (Frigidaire-built)✔️ Whirlpool✔️ Maytag✔️ Crosley✔️ White-Westinghouse 📌 Need help verifying compatibility? Send us your dryer’s model number — we’ll check it for you. 🚚 Why Buy from Parts-O-Matic ? ✅ Reliable aftermarket performance ✅ Always Fast and Free U.S. shipping ✅ Easy DIY repair with trusted support ✅ Backed by excellent customer service 🛒 Fix your dryer’s latching issue today — order the EXP71 dryer door catch from parts-o-matic.com, and enjoy fast, free U.S. shipping!

Read more less