Search results for "dryer thermal fuse"

(5 Pack) XPARTCO XP5KV09A Microwave Line Fuse 0.9A, 5KV The XPARTCO XP5KV09A is a pack of 5 replacement high-voltage fuses for microwave ovens, each rated 0.9 A (900 mA) at 5 kV. Each is a glass-and-metal tube fuse that sits in the microwave's high-voltage circuit and protects it against overcurrent, so a fault such as a shorted diode or capacitor opens the fuse before it damages other components. When this fuse blows, the microwave typically stops heating or shuts down, although the lights, display, and fan can still work. These are universal-style fuses sold by rating, not by brand, so they fit any microwave that calls for a 0.9 A, 5 kV high-voltage fuse. The 5-pack covers the repair and leaves spares for the next one. A blown fuse is usually a symptom of another failed part, so the cause should be found and fixed as part of the repair. Replacement should be done by a qualified service technician. Quick Answer The (5 Pack) XPARTCO XP5KV09A Microwave Fuse is a pack of five 0.9 A, 5 kV high-voltage fuses for microwave ovens whose original fuse has blown, so the microwave won't heat. Match the rating printed on your old fuse before ordering. Classic symptom: the microwave powers on, the light and turntable work, but it does not heat food. Common Problems This Part Fixes Microwave runs but does not heat Microwave appears dead or shuts down when started, with a blown high-voltage fuse High-voltage fuse open or blackened after a component failure Keeping a rated spare on hand for technician repairs Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers These fuses are sold under the following part number and rating: XP5KV09A, F900mAL5KV, EAF36358314, DE91-70071A, DE91-70060B, F900mAL5KV, EAF36358314, ALG54035, PD00074794, AP5957954, PS10067115, WB26X35519, AGE22550, AP6997696. PD00096398, PS16542134, WB02X35377, AGE21237, AP6989400, PD00084692, PS16216933, WB27X35672, AGE22690, PD00078809, EAP16219548, AP6994733, PS16219548, EAF36358316, PD00051271, EAP10066444, ALG54048, AP5957955, PS10066444 This is a rating-based universal fuse, so there is no single manufacturer part number. Match your oven's fuse by the 0.9 A (900 mA), 5 kV rating marked on the old fuse or listed in your service manual. Compatibility These fuses are for microwave ovens that use a: 0.9 A (900 mA), 5 kV high-voltage fuse Note: Microwaves use different fuses, and the rating must match. Some use 0.75 A, 0.8 A, or other high-voltage ratings, and a separate low-voltage line fuse near the power cord (for example, 125 V, 20 A) is a different part. Check the rating on your old fuse or in your service manual. Contact our support team with your model number and we'll help verify before you order. Key Features Replacement high-voltage microwave fuses, 0.9 A (900 mA) at 5 kV Glass-and-metal tube construction Overcurrent protection for the microwave's high-voltage circuit Sold by rating, so they suit any microwave that calls for a 0.9 A, 5 kV fuse 5 fuses per pack, with spares for future repairs Product Specifications Part Number XP5KV09A Part Type Microwave High-Voltage Fuse Condition Aftermarket Replacement Current Rating 0.9 A (900 mA) Voltage Rating 5 kV Quantity 5 Fuses Construction Glass and Metal Tube Application Microwave Ovens Using a 0.9 A, 5 kV Fuse Installation Notes ⚠️ Danger: Lethal Charge — Qualified Technician Installation Only A microwave's high-voltage capacitor can hold a lethal electrical charge even after the microwave is unplugged. Replacing a high-voltage fuse should be done by a qualified service technician who knows how to safely discharge and test the high-voltage circuit. Do not open the microwave cabinet unless you are trained to do so. Unplugging the microwave does not make this circuit safe. A technician will normally unplug the unit, discharge the capacitor, and test the old fuse for continuity. Because a blown fuse is usually the result of another failed part, such as the diode, capacitor, or transformer, the cause should be found and corrected before the new fuse is fitted, or it will likely blow again. Fit the new fuse in the same holder, confirm the rating matches, keep the remaining fuses as spares, and make sure all covers are back in place before powering the microwave. Frequently Asked Questions My microwave runs but won't heat. Is this the part I need? A blown high-voltage fuse is one possible cause, along with a failed diode, capacitor, magnetron, or transformer. A technician can test the fuse for continuity. If it has none, replace it, and find out why it blew. How do I know if I need a 0.9 A fuse? Check the rating printed on your old fuse or listed in your oven's service manual. The rating must match. Other microwaves use different ratings, so contact our support team with your model number if you're unsure. Is this the same as a microwave line fuse near the power cord? No. A low-voltage line fuse, such as a 125 V, 20 A one, is a different part. This is a high-voltage fuse rated 0.9 A at 5 kV. How many fuses come in this order? Each order includes 5 fuses. Can I install this myself? We recommend installation by a qualified technician only. The high-voltage circuit can hold a lethal charge even when the microwave is unplugged. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

WE04X28977 Dryer Genuine Door Switch The WE04X28977 is a genuine GE dryer door switch for GE and Hotpoint dryers, and also fits select Haier, Monogram, and Café models built on the GE platform. This small latch-style switch communicates with the control board when the door is fully closed, allowing the drying cycle to safely begin, and signals the control board to stop the cycle if the door is opened during operation. White in color, measuring approximately 3"H x 2"W, weighing about 1 lb. Also known by the part number WE10X23879. Over time, this switch can become damaged from extended use or excessive force when closing the door. Symptoms of a failing door switch include the dryer failing to start, or the door not closing or latching properly. Replacing this switch requires a few basic tools and some slight disassembly of the dryer. It directly replaces WE10X23879, 4931170, AGE25215, AP6889035, EAP12722948, PD00053592, PS12722948. Quick Answer The WE04X28977 Dryer Genuine Door Switch fixes GE, Hotpoint, Haier, Monogram, and Café dryers that won't start or have a door that won't close or latch properly. White, small latch style, ~3"H x 2"W, ~1 lb. Replaces WE10X23879, 4931170, AGE25215, AP6889035, EAP12722948, PD00053592, PS12722948. This is a dryer part — it's sold individually and typically requires removing the front panel for access. Common Problems This Part Fixes Dryer won't start Door won't close or latch properly Dryer stops mid-cycle when the door is bumped or jostled Switch damaged from excessive force when closing the door Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dryer door switch directly replaces the following OEM and cross-reference part numbers: WE04X28977, WE10X23879, 4931170, AGE25215, AP6889035, EAP12722948, PD00053592, PS12722948 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This door switch is compatible with select GE dryers, and also fits select Hotpoint, Haier, Monogram, and Café dryers built on the GE platform, including model numbers such as GTD42GASJ2WW, GTD45EASJ1WS, GTD45EASJ0WS, GTD45EASJ2WS, GTD42EASJ1WW, GTD42GASJ1WW, GTD72EBSN0WS, GTX22GASK0WW, GTD45GASJ2WS, GTD45GASJ1WS, GTX22EASK0WW, GTD42EASJ2WW, GTD42EASJ0WW, GTD42GASJ0WW, GTD72EBPN0DG, GTD45GASJ0WS, PTD60EBPR0DG, YTD74E2SN0WS, YTD74E2PN0DG, GTD84ECPN1DG, GTX52GASP0WB, PTD60GBSR0WS, GTD84GCPN0DG, VTD52EASR0WB, GTD84GCPN1DG, GTD84ECPN0DG, YTD74G2PN1DG, GTD84GCSN0WS, YTD74G2PN0DG, PTD60EBSR0WS, YTD74E2PN1DG, PTD60GBPR0DG, YTD74E2SN1WS, GTD84GCSN1WS, GTD65EBSJ4WS, VTD52GASR0WB, GTD84ECSN0WS, YTD74G2SN0WS, GTD84ECSN1WS, YTD74G2SN1WS, GTX52EASP0WB, HTX24GASK0WW, HTX24GASK0WS, HTX21EASK0WW, HTX21PASK0WW, HTX24EASK0WS, HTX24EASK0WW, HTX21GASK0WW, GTX65EBSJ2WS, GTD75ECPL0DG, GTD75GCPL0DG, GTD65GBSJ4WS, GTX42GASJ1WW, GTX65GBSJ2WS, GTD33PASK0WW, GTX33EASK0WW, GTX33GASK0WW, GTX60EBSJ0WS, GTD65EBSJ0WS, GTD65EBSJ3WS, GTX42EASJ1WW, 5TX62E9ST0WS, 5TX62E9ST1WS, 5TX62G9ST0WS, and ETD48EASW0WB. Note: This is a dryer part, sold individually. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Genuine GE OEM part — factory-specified switch design Small latch-style door switch — communicates door status to the control board Resolves "won't start" and "door won't close" symptoms caused by switch failure White, approximately 3"H x 2"W, about 1 lb Also known as WE10X23879 Direct drop-in replacement matching the original mounting Replaces WE10X23879, 4931170, AGE25215, AP6889035, EAP12722948, PD00053592, PS12722948 Compatible with GE, Hotpoint, Haier, Monogram, and Café dryers Genuine OEM replacement — guaranteed fit, materials, and performance Sold individually Product Specifications Part Number WE04X28977 Also Known As WE10X23879 Part Type Dryer Door Switch (Small Latch Style) Condition Genuine OEM Brand GE Color White Height Approx. 3" Width Approx. 2" Weight Approx. 1 lb Repair Difficulty Easy to Moderate — front panel removal required Quantity 1 door switch (sold individually) Compatible Brands GE, Hotpoint, Haier, Monogram, Café Installation Notes ⚠️ Unplug Dryer Before Starting Disconnect power at the outlet before beginning. Wear work gloves. Turn the two screws located at the bottom corners of the front panel counter-clockwise until they come out, then slide the panel up and off the dryer to access the door switch. Locate the wires connected to the old door switch and disconnect them, noting their positions. Remove the mounting screws or clips securing the old switch and pull it free. Install the new WE04X28977 in the same position, reconnect the wires to their original positions, and secure the mounting hardware. Slide the front panel back into place and secure the two bottom corner screws. Restore power and test that the dryer starts normally with the door closed, and stops if the door is opened during a cycle. Tools needed: screwdriver, wrench, pliers. Frequently Asked Questions My dryer won't start. Is this the part I need? Yes, this is one of the most common symptoms of a failed door switch. Since this switch tells the control board whether the door is closed, a damaged or malfunctioning switch can prevent the dryer from starting even when the door is fully shut. My dryer door won't close properly. Could this be the same part? Yes, a damaged door switch — often from excessive force when closing the door over time — can cause the door to not latch or close correctly, in addition to preventing the dryer from starting. Is this a difficult repair? It's a straightforward repair for a confident DIYer, requiring a screwdriver, wrench, and pliers, along with some slight disassembly of the dryer's front panel to access the switch. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by GE to factory specifications — guaranteed fit, materials, and performance. It matches the original switch design and mounting configuration of the door switch originally installed in your dryer. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

WE11X203 Dryer Genuine OEM Heater Restring Coil Kit  Dryer heating element restring kit. This kit replaces the existing heating coil in your dryer.  This Heater restring Coil Replaces WE11X103 Heater Restring Coil.  The diameter of the coil is 1/2" OD it stretches around the pan over the ceramic insulators.   Replaces Part Numbers:WE11X203, AH265619, AP2620176, DE333, EA265619, K35-408, PS265619, WE11X0203, WE11X103C   California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

XPARTCO EXP445 Dryer Repair Kit Replaces 4581EL2002C, 4400EL2001F, 4561EL3002A The XPARTCO EXP445 is a complete aftermarket dryer maintenance kit for LG-built dryers sold under the LG and Kenmore brands, bundling the three components that most commonly wear out together as a dryer ages: the drum support rollers, the drive belt, and the idler pulley. Rather than ordering these parts one at a time as each fails, this kit lets you service the whole drum support and drive system in a single repair — the recommended approach once any one of these parts shows wear, since they all take similar stress and tend to fail in the same general time frame. This kit includes 4 drum support rollers with metal shafts and high-strength bearings, 1 reinforced rubber drive belt, and 1 idler pulley assembly. It directly replaces roller numbers 4581EL2002L, 4581EL2002H, 4581EL2002C, 4581EL2002A, 4581EL2002D, 4581EL2002E, 4581EL3001A, 4581EL3001C, 4581EL3001F, AGM75510755, AP7220429, PS17269866; belt numbers 4400EL2001F, 4400EL2001A, 4400EL2001C, 4400EL2001E, 4115028, AP5972814, PS11705916; and idler pulley numbers 4561EL3002A, 4561EL3002B, AH3523033, EA3523033, AP4438243, PS3523033. Installs in 60–90 minutes with basic hand tools. Quick Answer The XPARTCO EXP445 Dryer Repair Kit fixes LG and Kenmore (LG-built) dryers with a loud rumbling/squeaking noise, a slipping or squealing belt, or a drum that won't turn — the classic signs that the drum support and drive system need a complete service. Includes 4 drum rollers, 1 drive belt, and 1 idler pulley. Replaces 4581EL2002L/H/C/A/D/E, 4581EL3001A/C/F, AGM75510755, AP7220429, PS17269866, 4400EL2001F/A/C/E, 4115028, AP5972814, PS11705916, 4561EL3002A/B, AH3523033, EA3523033, AP4438243, PS3523033. Classic symptom: loud rumbling that progresses to a squealing belt and, eventually, a drum that stops turning. Common Problems This Part Fixes Loud rumbling, thumping, or squeaking noise from the dryer during operation High-pitched squealing noise, especially at startup or when the drum is heavily loaded Dryer runs but the drum doesn't turn (motor runs, drum stays still) Burning rubber smell from a slipping or worn belt Drum riding unevenly, wobbling, or vibrating during the cycle Belt visibly frayed, cracked, or glazed/shiny from slipping What's In The Kit Component Qty Replaces Drum Support Roller (w/ shaft & bearing) 4 4581EL2002L, 4581EL2002H, 4581EL2002C, 4581EL2002A, 4581EL2002D, 4581EL2002E, 4581EL3001A, 4581EL3001C, 4581EL3001F, AGM75510755, AP7220429, PS17269866 Drive Belt (reinforced rubber, poly-V) 1 4400EL2001F, 4400EL2001A, 4400EL2001C, 4400EL2001E, 4115028, AP5972814, PS11705916 Idler Pulley Assembly 1 4561EL3002A, 4561EL3002B, AH3523033, EA3523033, AP4438243, PS3523033 Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This repair kit directly replaces the following OEM and cross-reference part numbers: EXP445, 4581EL2002L, 4581EL2002H, 4581EL2002C, 4581EL2002A, 4581EL2002D, 4581EL2002E, 4581EL3001A, 4581EL3001C, 4581EL3001F, AGM75510755, AP7220429, PS17269866, 4400EL2001F, 4400EL2001A, 4400EL2001C, 4400EL2001E, 4115028, AP5972814, PS11705916, 4561EL3002A, 4561EL3002B, AH3523033, EA3523033, AP4438243, PS3523033 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This repair kit is compatible with select LG-built dryers from the following brands: LG dryers (including DLE7177WM, DLE5955W, DLEX3470V, and related models) Kenmore / Sears dryers (select LG-built models, including 796.81022900) Note: This kit is specific to LG's roller/belt/pulley platform and uses a different belt and roller design than Whirlpool-, GE-, or Samsung-built dryers. Always verify your appliance model number before ordering. Contact our support team with your model number if you're unsure. Key Features Complete drum support and drive system service kit — rollers, belt, and idler pulley in one order Resolves "rumbling," "squealing belt," "drum won't turn," and "burning smell" symptoms together 4 drum support rollers with metal shafts and high-strength bearings 1 reinforced rubber poly-V drive belt 1 idler pulley assembly that keeps tension on the belt Services the components most likely to wear out together, reducing repeat repair trips Replaces 4581EL2002L/H/C/A/D/E, 4581EL3001A/C/F, 4400EL2001F/A/C/E, 4561EL3002A/B, and additional cross-reference numbers Compatible with LG and Kenmore (LG-built) dryers Aftermarket replacement built to OEM-equivalent quality standards Product Specifications Part Number EXP445 Kit Type Dryer Drum Roller, Belt & Idler Pulley Repair Kit Condition Aftermarket Replacement Rollers Included 4 (with shaft, bearing, mounting hardware) Belt Included 1 (reinforced rubber, poly-V) Idler Pulley Included 1 Application LG-Built Dryer Drum Support & Drive System Compatible Brands LG, Kenmore Installation Notes ⚠️ Unplug Dryer Before Starting Disconnect power before beginning. Remove the front panel (typically held by spring clips or screws behind the door frame) and carefully lift the drum out, supporting it so it doesn't drop or scratch the cabinet. With the drum removed, replace all 4 drum support rollers on their shafts, securing each with its retaining nut/washer. Slip the old belt off the motor pulley and remove the old idler pulley from its mounting bracket. Install the new idler pulley, then route the new belt around the drum and motor pulley exactly as the old one was routed (photograph the belt routing before removal) — the belt typically threads under the idler pulley with the ribbed side against the drum. Reinstall the drum onto the new rollers, verify the belt sits centered and properly tensioned, and reinstall the front panel. Restore power and run a test cycle to confirm quiet, smooth operation. Tools needed: nut driver or socket set, putty knife (for spring clips, if applicable), and a camera or phone to document belt routing before disassembly. Frequently Asked Questions Why buy a full kit instead of just the failed part? The rollers, belt, and idler pulley all experience similar wear over the dryer's life and tend to fail within a similar timeframe of each other. Since the drum has to come out to access any one of these parts, most technicians and experienced DIYers replace all three at once — it costs less in total labor and time than doing three separate repairs as each part fails one after another. My dryer runs but the drum doesn't turn — is this the kit I need? Yes, in most cases. A drum that doesn't turn while the motor runs is almost always caused by a broken drive belt or a seized idler pulley. Since this kit includes both, along with the rollers that are commonly worn by the time the belt fails, it addresses the full drive system in one repair. Will this fit my Whirlpool, GE, or Samsung dryer? No — this kit is specific to the LG-built roller/belt/pulley platform used in LG and select Kenmore dryers. Other brands use different roller, belt, and pulley designs that this kit will not fit. Confirm your appliance model number before ordering. Do I need to photograph the belt routing before removing the old one? Yes, strongly recommended. LG dryer belts route around the drum and motor pulley in a specific path, often threading under the idler pulley in a particular orientation. Photographing the routing before removal makes reinstallation straightforward and avoids a belt that runs off-track or slips after reassembly. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO 279393 Dryer Terminal Block Screw Kit The XPARTCO 279393 is an aftermarket replacement terminal block screw kit compatible with a wide range of Whirlpool-family electric dryers including Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Roper, Admiral, Estate, Crosley, Inglis, Magic Chef, and Norge. The terminal block screws secure the dryer power cord wires to the terminal block — the connection point where 240V power enters the dryer. Loose, corroded, or damaged screws at this connection can cause intermittent power loss, blown fuses, tripped breakers, or dangerous arcing. This kit includes 3 chrome-plated screws and 3 nuts — everything needed to restore a secure, conductive connection at the terminal block. The chrome plating improves electrical conductivity and corrosion resistance. Screws measure 7/16" L x 7/16" W x 11/16" H; nuts measure 1/2" L x 1/2" W x 1/8" H. Installs in under 15 minutes with basic hand tools. Quick Answer The XPARTCO 279393 Terminal Block Screw Kit fixes electric dryers with intermittent power, blown fuses, tripped circuit breakers, hot terminals, or visible arcing and scorching at the power cord connection. Includes 3 chrome-plated screws and 3 nuts. Compatible with Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Roper, Admiral, and more. Common Problems This Part Fixes Dryer has intermittent power or will not start at all Internal fuses repeatedly blowing without another clear cause Circuit breaker for the dryer repeatedly tripping Terminal block area is hot to the touch during or after operation Visible arcing, sparks, scorch marks, or smoke around the terminal block cover Heating element or motor works intermittently but not consistently Dryer power cord connection is loose, corroded, or visibly damaged Replaces Part Numbers This terminal block screw kit directly replaces the following OEM and cross-reference part numbers: 279393, 279393D, 279393VP, 3184, EAP334188, AWP39844, PD00003883, AH334188, EA334188, AP3020386, PS334188 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This terminal block screw kit is compatible with select electric dryers from the following brands: Whirlpool electric dryers Kenmore / Sears electric dryers (Whirlpool-built models) Maytag electric dryers KitchenAid electric dryers Amana electric dryers Roper electric dryers Admiral electric dryers Estate electric dryers Crosley electric dryers Inglis electric dryers Magic Chef, Norge, and Jenn-Air electric dryers Note: This kit is for electric dryers only. Gas dryers do not use a terminal block for power cord connections. Key Features Secures the dryer power cord wires to the terminal block for a safe, reliable 240V connection Kit includes 3 screws and 3 nuts — one complete set for all three terminal positions Chrome-plated metal construction — improves electrical conductivity and resists corrosion Screw dimensions: 7/16" L x 7/16" W x 11/16" H; Nut dimensions: 1/2" L x 1/2" W x 1/8" H Direct replacement for OEM part numbers 279393, 279393D, and 279393VP — no modification required Compatible with Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Roper, Admiral, and more Aftermarket replacement built to OEM-equivalent quality standards Quick DIY repair — installs in under 15 minutes with basic hand tools Product Specifications Part Number 279393 Part Type Terminal Block Screw and Nut Kit Condition Aftermarket Replacement Application Electric Dryers (240V terminal block) Kit Contents 3 chrome-plated screws and 3 nuts Screw Dimensions 7/16" L x 7/16" W x 11/16" H Nut Dimensions 1/2" L x 1/2" W x 1/8" H Material Chrome-plated metal Compatible Brands Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Roper, Admiral, Estate, Crosley, Inglis, Magic Chef, Norge, Jenn-Air Dryer Type Electric dryers only ⚠️ Electrical Safety Warning This kit connects the power cord to the dryer's terminal block — a high-voltage connection carrying 240V. Always unplug the dryer and shut off the circuit breaker before beginning installation. Loose or improperly tightened terminal screws can cause arcing, overheating, blown fuses, or fire. If you are not comfortable working with high-voltage electrical connections, have this part installed by a qualified appliance technician. Installation Notes ⚠️ Unplug and Switch Off Breaker Before Starting Unplug the dryer from the wall outlet and turn off the circuit breaker for the dryer before beginning any work on the terminal block. Locate the terminal block cover plate on the back of the dryer and remove it by unscrewing the retaining screw. Use needle-nose pliers to carefully disconnect the power cord wires from the terminal block. Remove the old screws and nuts using a Phillips or flat-head screwdriver. Install the new 279393 screws and nuts into the terminal block. Reconnect the power cord wires to the correct terminals — refer to the label inside the terminal block cover or your dryer's wiring diagram to confirm wire positions. Tighten all screws firmly but do not overtighten. Replace the terminal block cover plate. Restore power and run a test cycle to verify correct operation. Tip: While the cover is off, inspect the terminal block itself (part 694431) for burn marks or damage. If the block is damaged, replace it before reinstalling. Tools needed: Phillips screwdriver, flat-head screwdriver, needle-nose pliers. Frequently Asked Questions What is the terminal block screw kit used for? The terminal block screw kit secures the three wires of the dryer's power cord (two hots and a neutral, or two hots and a ground depending on cord type) to the terminal block at the back of the dryer. This is the point where 240V power enters the machine. The screws must be firmly tightened to maintain a safe, low-resistance electrical connection. If they loosen or corrode over time, resistance increases at the connection — causing heat, arcing, blown fuses, or power loss. Can I also use this kit when installing a new dryer power cord? Yes — this kit is commonly needed when installing a new 3-wire or 4-wire dryer power cord. When switching from a 3-wire to 4-wire cord (or vice versa), the terminal block screws and nuts often need to be loosened and retightened, and replacing them with a fresh set ensures a secure, corrosion-free connection from the start. Should I also inspect the terminal block itself? Yes. While the terminal block cover is off, inspect the block itself (part 694431) for burn marks, melted plastic, or damaged terminals. If the block shows any of these signs, it should be replaced before reinstalling — new screws alone cannot fix a damaged terminal block. Contact our support team to find the correct terminal block for your model. Does this kit work for gas dryers? No. Gas dryers use a standard 120V three-prong household plug and do not have a terminal block for power cord connections. The 279393 kit is for electric dryers only, which use a 240V outlet and require a hard-wired terminal block connection for the power cord. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is made from chrome-plated metal to match the dimensions and electrical performance of the original 279393 screw kit. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout  

Read more less

EXP25A Microwave 25A Ceramic Fuse, Fast Blow It can be used in many applications.    California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

Genuine OEM WP3406107 Dryer Door Switch The Genuine OEM Whirlpool WP3406107 is a dryer door switch for Whirlpool, Kenmore, Maytag, and KitchenAid dryers. It mounts inside the top of the dryer's front panel, with one end connecting to the wiring harness and the other passing through the panel to make contact with the door. When the door closes, it presses the switch's black tab, which tells the dryer the door is shut so it can run. When the switch wears out, the dryer may not start, may run with the door open, or may lose its interior light. This is the original Whirlpool part, a white, 6.5 inch, three-wire switch. Retailers describe the switch as a regular wear part and rate the repair as really easy, typically 15 to 30 minutes. Quick Answer The Genuine OEM WP3406107 Door Switch fixes a Whirlpool, Kenmore, Maytag, or KitchenAid dryer that won't start, runs with the door open, has a light that doesn't work, or has a door that won't close properly. Quick test: with the dryer unplugged, press the switch's black tab. If it has no resistance and doesn't click, the switch likely needs replacing. Common Problems This Part Fixes Dryer won't start Dryer runs with the door open Interior light doesn't work Door won't close or latch properly against the switch Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This door switch directly replaces the following part numbers: WP3406107, WPW10569603, 3406107, W10569603, 3405100, 3405101, 3406100, 3406101, 528948, 11259-65, 11288-80, WP3406107VP, AP6008561, AWP47183, EAP11741701, PD00002378, PS11741701 These numbers come from retailer cross-reference lists and span several generations of Whirlpool's own numbering for this switch. Confirm against your dryer's parts diagram, or contact our support team, if your model calls out a different number. Compatibility This door switch is listed for Whirlpool, Kenmore, Maytag, and KitchenAid dryers, including these examples: Kenmore 11060372710, 11060522900, 11060702990, 11060802990 Kenmore 11061202010, 11061262311, 11061802000 Whirlpool EED4400WQ Note: The models above are a small sample of a longer list, not a full list. This is a three-wire switch that replaces the two-wire switch found on many models, so compare it to your old switch, and contact our support team with your model number to verify fit before ordering. Key Features Genuine OEM Whirlpool dryer door switch, not an aftermarket equivalent Three-wire design; replaces the two-wire switch on many models White, 6.5 inch switch with a spring-loaded black tab Resolves no-start, runs-with-door-open, and light problems caused by a worn switch Typically a 15 to 30 minute repair Product Specifications Part Number WP3406107 OEM Part Number WP3406107 Part Type Dryer Door Switch Condition Genuine OEM Manufacturer Whirlpool Length 6.5 Inches Color White Wire Configuration Three-Wire Application Whirlpool, Kenmore, Maytag & KitchenAid Dryers Installation Notes ⚠️ Unplug Power Before Installing Unplug the dryer before beginning, and shut off the gas supply first on gas models. Wear work gloves, as cabinet edges can be sharp. The switch is mounted inside the top of the front panel, so follow your model's service guide to remove the panel needed to reach it. Note how the wiring connector is attached, disconnect it, and remove the old switch. Fit the new switch in the same position, reconnect the wiring, and reassemble. Restore power and confirm the dryer starts with the door closed and stops when the door is opened. Frequently Asked Questions My dryer won't start. Is this the part I need? A worn door switch is a common cause. With the dryer unplugged, press the switch's black tab. If there is no resistance and no click, the switch likely needs replacing. My dryer runs with the door open. Is that a problem? Yes. The door switch is a safety part that stops the dryer from running when the door is open. If the dryer runs with the door open, replace the switch promptly. My dryer has a two-wire switch. Will this three-wire switch work? Retailers list this three-wire switch as the replacement for the two-wire switch found on many models. Compare it to your old switch and your wiring, or contact our support team with your model number, before ordering. Will this fit my dryer? It is listed for many Whirlpool, Kenmore, Maytag, and KitchenAid dryers, but the model list above is only a sample. Check your model number against your parts diagram, or contact our support team and we'll verify it before you order. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Genuine OEM Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

(5 Pack) XP15A-SB Ceramic Line Fuse, Slow Blow, 15A – 6.35 x 32 mm Product Description Protect electrical circuits from overload and short circuits with the XP15A-SB Ceramic Line Fuse, Slow Blow, 15A – 6.35 x 32 mm. This slow-blow (time-delay) fuse is designed to handle temporary current surges while providing reliable overcurrent protection for appliances and electronic equipment. The ceramic body enhances heat resistance and arc containment, making it suitable for high-power applications such as microwave ovens, power supplies, industrial equipment, and control boards. When excessive current occurs, the fuse safely interrupts the circuit to prevent damage to internal components. Replaces Part Numbers WPM0805102, PD00097645, AP6014670, PS11747932, 3601-001197, 3601-000438, AP4046099, PS4131368, WB27X10454, WB08T10027, WB2X8151, WB02X8151, PD00032463, AP3189379, PS239596, 14QBP15CSB, TJ14QBP15CSB, CF15SB, 14QBP0243, 14QBP0315, 14QBP15CSB, 14QBP15GSB, AP5633499, MWF15B, HES-170-031, WPY01050009, PD00091249, OEM18072261, AP6024084, CF15SBCM. Compatibility This 15A slow-blow ceramic fuse is commonly used in: Microwave ovens Power supply units Appliance control boards Industrial equipment Audio amplifiers Always verify amperage (15A), size (6.35 x 32 mm), and slow-blow specification before ordering.Contact our support team if you’re unsure. ✅ Key Features 🔄 Slow Blow (Time Delay) – Handles temporary current surges ⚡ 15 Amp Rating – Protects against overload and short circuits 🔥 Ceramic Body Construction – High heat resistance and arc containment 📏 Standard Size – 6.35 mm x 32 mm (1/4" x 1-1/4") 💪 Reliable Circuit Protection – Designed for appliance and electronic safety 📐 Product Specification Part Number: XP15A-SB Type: Ceramic Line Fuse Blow Type: Slow Blow (Time Delay) Current Rating: 15 Amps Voltage Rating: 250V Size: 6.35 mm x 32 mm (1/4" x 1-1/4") Application: Over-current protection Quality Level: Aftermarket replacement 🛠️ Installation Notes Tools Needed: Fuse puller or insulated pliers ⚠️ Safety First: Disconnect power before replacing any fuse to prevent electrical shock. Basic Steps: Turn off and unplug the device. Locate the fuse holder. Remove the blown fuse carefully. Install the new XP15A-SB 15A slow-blow fuse. Restore power and test operation. ⏱️ Time Required: Under 5 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Appliance & Electrical Parts Supplier 🔄 30-Day Return Policy Protect your equipment with reliable overcurrent protection — Add to Cart Now for a dependable replacement fuse!

Read more less

279570 Genuine OEM Whirlpool Dryer Door Catch Kit The 279570 is a Genuine OEM Whirlpool dryer door catch and strike kit compatible with a wide range of Whirlpool, Kenmore, Roper, Estate, Amana, Crosley, Inglis, KitchenAid, Maytag, and Admiral dryers. The door catch is the spring-clip mechanism on the dryer door that snaps over the door strike to hold the door firmly closed during operation, activating the door switch so the dryer can run. When the catch breaks, wears out, or loses tension, the door will not stay closed, the door switch will not be activated, and the dryer will either not start or will stop mid-cycle. The strike is the corresponding post or tab on the dryer cabinet that the catch engages. This Genuine OEM kit includes three color-coded door catches of different tensions and two metal door strikes, plus one screw. Because the tension of the catch must match the original, Whirlpool includes three options in the kit — each is color-coded and numbered on the back. Refer to identify which catch is correct for your model. The kit directly replaces a very large list of older cross-reference numbers including 279570VP, 3493, 2003, 8208, 279280, 279337, 696144, 693717, AP3094183, PS334230, and dozens more. Installs in under 15 minutes with a Phillips screwdriver. Quick Answer The 279570 Genuine OEM Whirlpool Dryer Door Catch Kit fixes dryers where the door won't stay closed, pops open mid-cycle, or won't activate the door switch to start. Kit includes 3 color-coded catches (different tensions), 2 metal strikes, 1 screw. Use the catch that matches your original. Genuine OEM. Compatible with Whirlpool, Kenmore, Roper, Estate, Amana, Crosley, Inglis, KitchenAid, Maytag, and Admiral dryers. Installs in under 15 minutes. Common Problems This Kit Fixes Dryer door will not stay closed during the drying cycle Door pops open mid-cycle, stopping the dryer Dryer will not start — door switch not being activated by a worn or broken catch Door feels loose or does not click shut firmly when closed Door catch visibly cracked, broken, or missing Door strike bent or missing — door cannot engage the catch properly Dryer requires the door to be held or pushed closed to stay running Replaces Part Numbers This door catch kit directly replaces the following OEM and cross-reference part numbers: 279570, 14205029, 14205577, 14210022, 2003, 236876, 236877, 241282, 241890, 26000279570, 261847, 263067, 279280, 279337, 279469, 279570VP, 291949, 3390239, 3392538, 3398175, 342295, 347813, 3493, 4165234, 51651001, 51655001, 66021, 690081, 690082, 693717, 694343, 696144, 8208, 830751, 834767, 834813, 834943, 834944, AH334230, DE902, EA334230, EAP334230, FSP279570, AP3094183, AWP39897, PD00002346, PS334230. Contact our support team with your model number if you need confirmation before ordering. Compatibility This door catch kit is compatible with select dryers from the following brands: Whirlpool dryers (gas and electric) Kenmore / Sears dryers (Whirlpool-built models) Roper dryers Estate dryers Amana dryers Crosley dryers Inglis dryers KitchenAid dryers Maytag dryers Admiral dryers Important: This kit includes three catches with different spring tensions, color-coded and numbered on the back. You must use the catch that matches the tension of your original. Using the wrong tension catch may result in a door that is too hard to open or too easy to pop open. Key Features Genuine OEM kit manufactured by Whirlpool to factory specifications — guaranteed fit and performance Holds the dryer door closed and activates the door switch so the dryer can run safely Kit includes 3 color-coded door catches (different spring tensions), 2 metal door strikes, 1 screw Catches are color-coded and numbered on the back — use the one that matches your original. Plastic catches with metal strikes and metal screw — durable construction for long service life Consolidates a very large list of older Whirlpool-family door catch cross-reference numbers Compatible with 10 major appliance brands on the Whirlpool platform Quick DIY repair — installs in under 15 minutes with a Phillips screwdriver Product Specifications Part Number 279570 Part Type Dryer Door Catch and Strike Kit Condition Genuine OEM Application Gas and Electric Dryers Kit Includes 3 color-coded door catches (different tensions), 2 metal strikes, 1 screw Material Plastic catches / Metal strikes Color White / Silver Catch Selection Color-coded and numbered, Use the catch that matches your original Compatible Brands Whirlpool, Kenmore, Roper, Estate, Amana, Crosley, Inglis, KitchenAid, Maytag, Admiral Installation Notes ⚠️ Unplug Dryer Before Starting Disconnect power before beginning. using the wrong tension catch will result in incorrect door resistance. Open the dryer door and locate the old door catch on the inside of the door panel and the strike on the dryer cabinet opening. To remove the old catch: press the retaining tabs and pull the catch free from its slot, or unscrew the mounting screw. Install the correct new catch into the same position. To replace the strike: remove the old strike (typically held by a single screw) and install the new strike in the same position. Close the dryer door to confirm it latches firmly with a satisfying click. Restore power and run a short test cycle to confirm the door stays closed and the dryer operates normally. Tools needed: Phillips screwdriver; needle-nose pliers may help with catch removal on some models. Frequently Asked Questions Why does the kit include three different catches? Whirlpool used door catches with different spring tensions across its dryer lineup — a lighter catch on some models and a stiffer catch on others. To cover all compatible models in a single kit, Whirlpool includes three catches of different tensions, each color-coded and numbered on the back. It is important to use the correct one — using a catch with too little tension may allow the door to pop open, while a catch with too much tension may make the door difficult to open. Do I need to replace both the catch and the strike, or just one? It depends on which component has failed. The catch (the spring-clip on the door) is the more commonly replaced part — it wears out from repeated use faster than the strike. Inspect both: if the catch is cracked or has lost its spring tension, replace the catch. If the strike is bent, cracked, or missing, replace the strike. Since the kit includes both catches and strikes, you have everything needed for a complete repair. When in doubt, replacing both ensures the full latch system is renewed. My dryer will not start even after replacing the door catch — what else could it be? If the dryer still will not start after the catch is replaced, the door switch may also need to be tested. The door switch is the electrical component that the door catch activates when the door closes — if the switch itself is failed, replacing the catch alone will not restore function. Test the door switch (3406107 for most Whirlpool-family models) with a multimeter for continuity in both the open and closed positions. If the switch reads open in both positions or closed in both positions, it has failed and needs replacement. How is the 279570 different from the W11429587 dryer door catch? The 279570 is the door catch kit for older Whirlpool-family dryers — it includes multiple catches of different tensions and metal strikes because it covers a wide range of older models. The W11429587 is a single snap-in door catch for newer Whirlpool-family dryers (Cabrio and newer platform models). If your dryer is a newer model with a snap-in catch slot rather than a screw-mounted catch and strike, you likely need the W11429587. Verify your model number to confirm which part is correct. Is this a Genuine OEM or aftermarket part? This is a Genuine OEM kit manufactured by Whirlpool to factory specifications. It is the exact same door catch and strike kit supplied by Whirlpool for compatible dryer service repairs — guaranteed fit, materials, and performance. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO WE01X20374 Dryer Timer Knob The XPARTCO WE01X20374 is an aftermarket replacement timer knob for GE dryers, and also fits select Hotpoint and RCA models. Located on the control panel, this knob mounts onto the timer's D-shaped shaft and lets you set desired drying times and select additional functions like air fluff or wrinkle release cycles. White in color, with a D-shaped opening for the timer shaft. Causes of a faulty timer knob include wear from repeated grasping and twisting over years of use, or exposure to high dryer temperatures degrading the knob material over time. Symptoms of a damaged timer knob include difficulty rotating the knob smoothly to desired time settings, the dryer not initiating cycles properly based on knob position, a loose or wobbling knob that could fall off, or cracking, chipping, or discoloration on the knob exterior. It directly replaces WE01X20374, WE1M856, 3276177, WE1M589, AGE25562, AP5805160, EAP8769912, PD00023120, PS8769912. Quick Answer The XPARTCO WE01X20374 Dryer Timer Knob fixes GE, Hotpoint, and RCA dryers with a knob that's hard to turn, doesn't properly select cycle settings, wobbles or feels loose, or shows cracking, chipping, or discoloration. White, D-shaped opening. Replaces WE01X20374, WE1M856, 3276177, WE1M589, AGE25562, AP5805160, EAP8769912, PD00023120, PS8769912. This is the correct knob to pair with certain GE dryer models where the similarly-numbered WE1M654 knob is not the right fit and can throw off cycle timing. Common Problems This Part Fixes Difficulty rotating the knob smoothly to desired time settings Dryer not initiating cycles properly based on knob position Loose or wobbling knob that could fall off Cracking, chipping, or discoloration on the knob exterior Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dryer timer knob directly replaces the following OEM and cross-reference part numbers: WE01X20374, WE1M856, 3276177, WE1M589, AGE25562, AP5805160, EAP8769912, PD00023120, PS8769912 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This timer knob is compatible with select GE dryers, and also fits select Hotpoint and RCA dryers built on the GE platform. Note — not the same as WE1M652 or WE1M654: These are separate, similarly-styled knobs used on other GE/Hotpoint models. GE's own support has confirmed cases where installing WE1M654 on the wrong model throws off cycle timing, and WE01X20374 is the correct part in those situations. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure which knob your dryer needs. Key Features Aftermarket replacement timer knob — direct interface for setting drying time and cycle functions Resolves "hard to turn," "won't select cycle correctly," "loose/wobbling," and "cracked or discolored" symptoms White finish, D-shaped opening for the timer shaft Direct drop-in replacement — no tools required for most installations Replaces WE01X20374, WE1M856, 3276177, WE1M589, AGE25562, AP5805160, EAP8769912, PD00023120, PS8769912 Compatible with GE, Hotpoint, and RCA dryers Aftermarket replacement built to OEM-equivalent quality standards Product Specifications Part Number XPWE01X20374 OEM Part Number WE01X20374 Part Type Dryer Timer Control Knob Condition Aftermarket Replacement Color White Shaft Opening D-shaped Extended Shaft 1/8" Repair Difficulty Very Easy — no tools typically required Quantity 1 timer knob Compatible Brands GE, Hotpoint, RCA Installation Notes ⚠️ Unplug Dryer Before Starting Disconnect power at the outlet before beginning. Remove the old knob by pulling it straight off the control shaft — no tools are typically required. Align the D-shaped socket on the new WE01X20374 with the flat side of the timer shaft, then press the new knob firmly onto the shaft until it's fully seated. Restore power and test that the knob turns the timer setting correctly through its full range, confirming the dryer starts and progresses through the cycle as expected. Tools needed: none typically required. Frequently Asked Questions My knob spins freely or feels loose. Is this the right part? Yes, this is one of the most common symptoms this knob resolves. If the knob's D-shaped socket has worn out or become stripped, it can no longer grip the timer's shaft properly, letting the knob spin, wobble, or feel loose without actually turning the internal timer mechanism. I was told my knob replacement threw off my drying time. Is WE01X20374 the fix? It can be, depending on your model. GE's own support has addressed a case where a similarly-numbered knob, WE1M654, was installed on the wrong model and caused the cycle to cut off before reaching the true "off" position — the customer was told the correct part for their model was WE01X20374. If your timing seems off after installing a different knob, double-check whether WE01X20374 is the correct part for your specific model. Is this a difficult repair? No, it's one of the simplest dryer repairs — the old knob pulls straight off the shaft and the new one presses straight on, with no tools needed. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine GE OEM part, but is manufactured to match the size, D-shaped shaft fit, and white finish of the original WE01X20374 timer knob used in compatible GE, Hotpoint, and RCA dryers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

4392067 Genuine OEM Whirlpool Dryer Repair Kit — Belt, Rollers & Idler (27") The 4392067 is a Genuine OEM Whirlpool dryer maintenance and repair kit that contains all the components most commonly replaced when a 27-inch Whirlpool-family dryer becomes noisy, stops tumbling, or starts vibrating — specifically the drum drive belt, all four drum support rollers, the idler pulley, tri-ring retaining clips, a washer, and installation instructions. Installing all of these components together in a single repair restores smooth, quiet drum rotation and eliminates the most common causes of dryer noise and drum drive failure in one visit. As a Genuine OEM kit assembled by Whirlpool to factory specifications, the 4392067 includes the belt (661570V), four rollers (WPW10314173), idler pulley (279640), nine tri-rings, one washer, and instructions. Compatible with 27-inch Whirlpool, Kenmore 110-series, Maytag, Roper, Estate, Crosley, Amana, and Admiral dryers built in 1965 or later. Important: the included belt (661570V, 93-1/2" x 1/4", 4-rib) is correct for many models but does not fit all — verify that 661570V is the correct belt for your specific model before ordering. It directly replaces AP3109602, 2015, 4392067VP, 587637, 80047, AH373088, EA373088, EAP373088, and PS373088. Installs in 45–60 minutes with basic hand tools. Quick Answer The 4392067 Genuine OEM Whirlpool Dryer Repair Kit fixes 27-inch Whirlpool-family dryers that are squealing, thumping, rumbling, or where the drum has stopped spinning. All-in-one kit: belt 661570V + 4 rollers (WPW10314173) + idler pulley (279640) + 9 tri-rings + washer + instructions. Genuine OEM. Important: belt 661570V fits many but not all models — verify your belt part number before ordering. Replaces AP3109602, 2015, 4392067VP, 587637, PS373088. Common Problems This Kit Fixes Loud squealing, squeaking, or thumping noise during the drying cycle Rumbling or grinding noise — worn drum support rollers Drum not spinning — broken or stretched drive belt Motor running but drum still — belt has snapped Belt repeatedly slipping — worn idler pulley no longer maintaining belt tension Burning rubber smell — slipping belt from a failed idler pulley Extended drying times — drum not rotating at correct speed due to belt or roller wear Excessive vibration during the drying cycle What's in the Kit Part 1 Drum Drive Belt — 661570V 93-1/2" long x 1/4" wide · 4-rib profile · Wraps around the drum and connects to the motor pulley and idler pulley to spin the drum · Important: 661570V is correct for many but not all compatible models — verify this belt number fits your specific dryer before ordering Parts 2–5 (qty: 4) Drum Support Rollers — WPW10314173 (set of 4) Cylindrical rubber-and-plastic wheels that support the drum rim as it rotates · LG/Whirlpool 27" dryer platform · Replace all 4 at the same time for even drum support Part 6 Idler Pulley Assembly — 279640 Spring-tensioned pulley wheel that presses against the drive belt to maintain correct belt tension · Pulley wheel only (not the arm) — mounts on the existing idler arm inside the dryer Hardware 9 Tri-Ring Retaining Clips + 1 Washer + Instructions Tri-ring clips secure the drum rollers to their mounting shafts · Washer provides proper spacing at roller shaft · Instruction sheet included Replaces Part Numbers This dryer repair kit directly replaces the following OEM and cross-reference part numbers: 661570V, 279640, WPW10314173, 8536974, 4392067, 2015, 4392067VP, 587637, 80047, AH373088, EA373088, AWP39353, EAP373088, PD00002451, AP3109602, PS373088. Contact our support team with your model number if you need confirmation before ordering. Compatibility This repair kit is compatible with 27-inch gas and electric dryers from the following brands (built 1965 or later): Whirlpool dryers (27" WED, WGD, Cabrio, Duet, and related series) Kenmore / Sears dryers — 110-series (Whirlpool-built models) Maytag dryers (Bravos XL and related series) Roper dryers Estate dryers Crosley dryers Admiral dryers Amana dryers (select models) Important — Belt Compatibility: The belt included in this kit is part number 661570V (93-1/2" x 1/4", 4-rib). This belt is correct for many 27-inch Whirlpool-family dryers but does not fit all compatible models. Before ordering, verify that 661570V is the correct belt part number for your specific dryer model. If your dryer uses a different belt, the rollers and idler pulley in this kit will still fit, but you will need to order the correct belt separately. Key Features Genuine OEM kit assembled by Whirlpool — all components manufactured to factory specifications All-in-one repair: belt (661570V) + 4 rollers (WPW10314173) + idler pulley (279640) + tri-rings + washer + instructions in a single box Replaces all the most commonly worn drum drive components in a single repair — eliminates the need for separate part orders and multiple teardowns For 27-inch Whirlpool-family dryers built 1965 or later Belt 661570V: 93-1/2" long x 1/4" wide, 4-rib — verify fit for your model before ordering Idler pulley (279640) is the pulley wheel only — mounts on the existing idler arm Compatible with Whirlpool, Kenmore 110-series, Maytag, Roper, Estate, Crosley, Admiral, and Amana Installs in 45–60 minutes with basic hand tools Product Specifications Kit Part Number 4392067 Condition Genuine OEM Application 27-inch Gas and Electric Dryers (built 1965 or later) Belt Included 661570V — 93-1/2"L x 1/4"W, 4-rib (verify fit for your model) Rollers Included 4x WPW10314173 drum support rollers Idler Pulley Included 279640 (pulley wheel only — not the arm) Hardware Included 9 tri-ring retaining clips, 1 washer, instructions Compatible Brands Whirlpool, Kenmore, Maytag, Roper, Estate, Crosley, Admiral, Amana Installation Notes ⚠️ Unplug Dryer Before Starting Disconnect power (and shut off gas for gas dryers) before beginning. Remove the top panel by inserting a putty knife under the front edge to release the spring clips, then lift. Remove the front panel to fully expose the drum. Take a photo of the existing belt routing before removing anything. Release the drive belt from the idler pulley and slide it off the drum. Remove the drum and set it aside. Replace all four drum support rollers — remove the old tri-ring clips with needle-nose pliers, slide the old rollers off the shafts, and install the new WPW10314173 rollers with new tri-rings and the included washer. Replace the idler pulley (279640) by pressing the new wheel onto the idler arm shaft. Route the new 661570V belt around the drum (ribbed side against the drum), under the idler pulley, and around the motor pulley. Reinstall the drum, front panel, and top panel. Restore power and run a test cycle. Tools needed: Phillips screwdriver, putty knife, needle-nose pliers, socket set. Frequently Asked Questions How do I know if the belt in this kit (661570V) fits my dryer? The belt included in this kit is 661570V (93-1/2" long, 1/4" wide, 4-rib). To confirm it is correct for your dryer, look up your dryer's model number in an online parts diagram and check the belt part number listed. If the parts diagram shows 661570V or its cross-reference 661570, this kit's belt is correct. If your diagram shows a different belt part number — for example 341241, W10205415, or WP8547157 — the rollers and idler in this kit will still fit your dryer, but you will need to order the correct belt separately. This is the most important compatibility check before purchasing this kit. Is the idler pulley (279640) a complete arm assembly or just the wheel? The 279640 included in this kit is the pulley wheel only — it does not include the idler arm or bracket. It presses onto the existing idler arm shaft inside your dryer. If the idler arm itself is cracked or broken, the arm assembly will need to be replaced separately. On most Whirlpool 27-inch dryers the arm itself rarely fails — it is the wheel bearing that wears out, which is what the 279640 wheel in this kit addresses. Why should I replace all four rollers instead of just the one that's noisy? All four drum support rollers wear at the same rate through the same number of drying cycles. When one roller starts making noise, the other three have experienced the same wear and are likely close behind. Replacing only the noisy roller leaves three worn rollers supporting the drum unevenly, often leading to a repeat repair within months. Since the dryer is already fully disassembled for this repair, replacing all four at once is the most cost-effective and long-lasting approach. How is the 4392067 kit different from the 4392065 kit? Both are Genuine OEM Whirlpool dryer repair kits but for different dryer platforms. The 4392065 is for older Whirlpool 29-inch dryers with the lint screen on top (contains belt 341241, 2 rollers 349241T, idler pulley 691366). The 4392067 is for newer Whirlpool 27-inch dryers with the lint screen inside the door — typically the Duet, Cabrio, Bravos XL, and Thin Twin platforms (contains belt 661570V, 4 rollers WPW10314173, idler pulley wheel 279640). They are not interchangeable — verify your dryer's lint filter location and model series before ordering. Is this a Genuine OEM or aftermarket part? This is a Genuine OEM kit assembled by Whirlpool to factory specifications. All components — belt, rollers, idler pulley, tri-rings, and washer — are the same parts installed in compatible Whirlpool, Kenmore, Maytag, and related brand 27-inch dryers from the factory. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XP25A-SB Ceramic Line Fuse, Slow Blow, 25A – 6.35 x 32 mm Product Description Protect high-current electrical circuits with the XP25A-SB Ceramic Line Fuse, Slow Blow, 25A – 6.35 x 32 mm. This time-delay (slow-blow) fuse is designed to tolerate temporary inrush currents while providing dependable overcurrent protection for appliances, industrial equipment, and power supply systems. The ceramic body construction offers superior heat resistance and arc containment compared to glass fuses, making it ideal for high-power applications. If excessive current flows, the fuse safely interrupts the circuit to prevent component damage or fire hazards. Replaces Part Numbers XP25A-SB, 25A 250V 6.35x32mm Slow Blow Fuse, MDL-25 equivalent style Compatibility This 25A slow-blow ceramic fuse is commonly used in: Microwave ovens Power supply units Industrial control equipment HVAC systems Amplifiers and high-current appliances Always verify amperage (25A), voltage rating (250V), and size (6.35 x 32 mm / 1/4" x 1-1/4") before ordering.Contact our support team if you’re unsure. ✅ Key Features 🔄 Slow Blow (Time Delay) – Handles temporary startup surges ⚡ 25 Amp Rating – Protects high-current circuits 🔥 Ceramic Body Construction – Enhanced heat and arc resistance 📏 Standard Size – 6.35 mm x 32 mm (1/4" x 1-1/4") 🛡️ Reliable Circuit Protection – Prevents overload damage 📐 Product Specification Part Number: XP25A-SB Type: Ceramic Line Fuse Blow Type: Slow Blow (Time Delay) Current Rating: 25 Amps Voltage Rating: 250V Size: 6.35 mm x 32 mm (1/4" x 1-1/4") Application: Overcurrent protection Quality Level: Aftermarket replacement 🛠️ Installation Notes Tools Needed: Fuse puller or insulated pliers ⚠️ Safety First: Disconnect power before replacing any fuse to prevent electrical shock. Basic Steps: Turn off and unplug the device. Locate the fuse holder. Carefully remove the blown fuse. Install the new XP25A-SB 25A slow-blow fuse. Restore power and test operation. ⏱️ Time Required: Under 5 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Appliance & Electrical Parts Supplier 🔄 30-Day Return Policy Protect your equipment with dependable overcurrent protection — Add to Cart Now for a reliable replacement fuse!

Read more less