Search results for "dishwasher heating"

XPARTCO XP6974 Dryer Thermostat Kit Replaces WP3387134, WP3392519, W10900067, 279816 The XPARTCO XP6974 is an aftermarket dryer thermostat kit containing four thermal components for Whirlpool-family electric and gas dryers including Whirlpool, Kenmore, Maytag, Amana, KitchenAid, Roper, Admiral, Estate, Crosley, Inglis, and Magic Chef. The kit includes the cycling thermostat (WP3387134), thermal fuse (WP3392519), high-limit thermostat and thermal cut-off kit (279816 / W10900067) — the complete set of heat-sensing and safety components that regulate dryer temperature and prevent dangerous overheating. These four components work together to control and protect the dryer's heating system. When any one of them fails, the dryer may produce no heat, overheat, run too long, or stop mid-cycle. Because a failed thermal fuse is almost always caused by an underlying overheating condition that also stresses the other components, replacing all four together in a single repair is the recommended approach. Includes all wiring hardware needed for installation. Installs in 20–30 minutes with basic hand tools. Quick Answer The XPARTCO XP6974 Dryer Thermostat Kit fixes Whirlpool-family dryers that produce no heat, overheat, take too long to dry, or stop mid-cycle. Includes all four thermal components: cycling thermostat (L155-25), thermal fuse (196°F), high-limit thermostat (L250-80), and thermal cut-off (309°F). Compatible with Whirlpool, Kenmore, Maytag, Amana, KitchenAid, Roper, Admiral, Estate, Crosley, Inglis, and Magic Chef electric and gas dryers. Common Problems This Kit Fixes Dryer produces no heat — thermal fuse or high-limit thermostat has blown Dryer takes multiple cycles or very long time to dry clothes Dryer overheats — clothes or drum too hot to touch after a cycle Dryer shuts off mid-cycle and will not restart Dryer tumbles normally but generates no heat at all Dryer runs too long because cycling thermostat is not regulating temperature Repeated thermal fuse failures — underlying thermostat fault causing recurring overheating What's in the Kit Part 1 of 4 WP3387134 Cycling Thermostat Rated L155-25 · Monitors drum air temperature and cycles the heating element on and off to maintain the set drying temperature · Located on the exhaust duct or blower housing · Should show closed continuity at room temperature Part 2 of 4 WP3392519 Thermal Fuse Opens at 196°F (91°C) · One-time safety device located on the exhaust duct · Permanently interrupts power to the heating element if the dryer overheats · Cannot be reset — must be replaced if blown · Most common cause of no-heat in Whirlpool-family dryers Part 3 of 4 High-Limit Thermostat (279816 / W10900067) Rated L250-80 · Mounted on the heating element housing · Opens at approximately 250°F to cut power to the heating element if temperature exceeds safe limits · Resets automatically when it cools · Should show closed continuity at room temperature Part 4 of 4 Thermal Cut-Off Fuse (3977393 / 279816 kit) Opens at 309°F · Backup one-time safety device on the heating element housing · Permanently interrupts power to the heating element if the high-limit thermostat fails to open · Cannot be reset — must be replaced if blown Replaces Part Numbers WP3387134 Cycling Thermostat cross-references: WP3387134, WP3387134VP, 3387134, 3387135, 3387139, 306910, 3-6910, ET187, AP6008270, PS11741405 WP3392519 Thermal Fuse cross-references: WP3392519, WP3392519VP, 3392519, 3388651, 694511, 80005, ET401, G4AP0500, AP6008325, PS11741460 279816 High-Limit Thermostat and Thermal Cut-Off Kit cross-references: 279816, 279816VP, W10900067, 3977393, 3977767, WP3977767, WP3977767VP, 3399848, 3399693, 2651, AP3094244, AH334299, EA334299, EAP334299, PS334299 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This thermostat kit is compatible with select gas and electric dryers from the following brands: Whirlpool dryers (gas and electric) Kenmore / Sears dryers (Whirlpool-built models) Maytag dryers (gas and electric) Amana dryers KitchenAid dryers Roper dryers Admiral dryers Estate dryers Crosley dryers Inglis dryers Magic Chef dryers Important: If your thermal fuse has blown, always check for the root cause before replacing — a clogged exhaust vent is the most common cause of dryer overheating. Clean the full length of the exhaust duct before or after this repair. If the vent is clear, a failed cycling thermostat or high-limit thermostat is likely the root cause. Key Features Complete 4-part thermal kit — covers the cycling thermostat, thermal fuse, high-limit thermostat, and thermal cut-off in a single repair Cycling thermostat (L155-25) — regulates drum temperature to maintain consistent, efficient drying Thermal fuse (196°F) — one-time safety device that permanently interrupts heat if the dryer overheats High-limit thermostat (L250-80, ~250°F) — cuts power to the heating element when temperature exceeds safe limits; auto-resets Thermal cut-off (309°F) — backup one-time safety device protecting against heating element runaway Replacing all four parts together ensures the complete thermal circuit is renewed — prevents recurrence if a failing thermostat caused the fuse to blow Includes all wiring hardware for installation Compatible with 11 major appliance brands on the Whirlpool platform Aftermarket replacement built to OEM-equivalent quality standards DIY repair — installs in 20–30 minutes with basic hand tools Product Specifications Kit Part Number XP6974 Condition Aftermarket Replacement Application Gas and Electric Dryers Kit Includes 1x WP3387134 Cycling Thermostat, 1x WP3392519 Thermal Fuse, 1x High-Limit Thermostat (L250-80), 1x Thermal Cut-Off Fuse (309°F), wiring hardware Cycling Thermostat Rating L155-25 (closes at 155°F, opens at 25°F differential) Thermal Fuse Trip Temp 196°F (91°C) — one-time, non-resettable High-Limit Thermostat Rating L250-80 (opens at ~250°F) — auto-resets Thermal Cut-Off Trip Temp 309°F — one-time, non-resettable Compatible Brands Whirlpool, Kenmore, Maytag, Amana, KitchenAid, Roper, Admiral, Estate, Crosley, Inglis, Magic Chef Installation Notes ⚠️ Unplug Dryer and Shut Off Gas Before Starting Disconnect power (and shut off gas for gas dryers) before beginning. Remove the back panel of the dryer to access the heating element housing and exhaust duct. The thermal fuse (WP3392519) and cycling thermostat (WP3387134) are located on the exhaust duct or blower housing — disconnect the wires, unscrew the mounting screws, and install the new parts in the same positions. The high-limit thermostat and thermal cut-off (279816 kit) are located on the heating element housing — disconnect the wires and unscrew the mounting screws to remove the old parts and install the new ones. Reconnect all wires to the correct terminals — take a photo before disconnecting to reference during reinstallation. Reassemble the back panel, restore power, and run a test cycle to verify heat. Tip: Before running the dryer, also clean the full length of the exhaust duct — a clogged vent is the most common root cause of dryer overheating and repeated thermal fuse failures. Tools needed: Phillips screwdriver, 1/4" nut driver, needle-nose pliers. Frequently Asked Questions What does each part in this kit do? The cycling thermostat (WP3387134) monitors the air temperature in the exhaust duct and cycles the heating element on and off to maintain the correct drying temperature — it is the part that controls how hot the dryer gets during normal operation. The thermal fuse (WP3392519) is a one-time safety device that permanently cuts power to the heating element if the dryer overheats above 196°F — it is the most common cause of no-heat in Whirlpool-family dryers. The high-limit thermostat opens at approximately 250°F to cut heating element power if temperature gets too high, and resets automatically when it cools. The thermal cut-off is a backup one-time fuse on the heating element that opens at 309°F if the high-limit thermostat fails to protect the heater. Why should I replace all four parts instead of just the one that failed? When a thermal fuse blows, it almost always blew because the dryer overheated — and that overheating event put significant stress on all the other thermal components as well. A failing cycling thermostat is the most common cause of repeated thermal fuse failures: if the cycling thermostat stops regulating temperature correctly, the dryer runs too hot, the high-limit thermostat is repeatedly stressed, and the thermal fuse eventually blows. Replacing just the fuse without replacing the cycling thermostat means the same overheating will blow the new fuse. Replacing all four parts at once eliminates that risk in a single repair. How do I test these parts with a multimeter? Set the multimeter to continuity or resistance mode. The thermal fuse (WP3392519), cycling thermostat (WP3387134), and high-limit thermostat should all show closed continuity (near-zero resistance) at room temperature. The thermal cut-off should also show closed continuity at room temperature. Any part that reads open (no continuity / infinite resistance) at room temperature has failed and needs to be replaced. A blown thermal fuse or cut-off will always read open — they are one-time devices and cannot reset. What causes the thermal fuse to blow repeatedly? The most common cause by far is a clogged exhaust vent — lint accumulation inside the dryer duct restricts airflow, causing heat to build up inside the dryer cabinet until the thermal fuse trips. Always clean the full length of the exhaust duct before and after replacing these parts. Other causes include a failing cycling thermostat that is not regulating temperature correctly, a stuck heating element relay, or a dryer placed in an enclosed space without adequate ventilation. Is this kit compatible with both electric and gas dryers? Yes — the XP6974 kit is compatible with both electric and gas Whirlpool-family dryers. Both types use the same cycling thermostat (WP3387134) and thermal fuse (WP3392519). The high-limit thermostat and thermal cut-off (279816 kit) are located on the heating element in electric models and on the burner assembly area in gas models. Always verify your specific model number before ordering to confirm all four parts apply to your dryer. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO DD62-00084A Dishwasher Water Valve – Compatible with Samsung Dishwashers Product Description Restore proper water flow and reliable cleaning performance with the XPARTCO DD62-00084A Dishwasher Water Valve. This Dishwasher Water Valve is an essential component for maintaining the optimal performance of your dishwasher. This replacement part ensures precise water flow control, allowing your dishwasher to operate efficiently and effectively. A faulty water valve can cause no water entering the dishwasher, slow filling, or poor cleaning performance. Replacing it with this dependable XPARTCO valve helps restore consistent water flow and efficient operation. XPARTCO provides cost-effective aftermarket appliance parts engineered to match original fit and function. Replaces Part Numbers DD62-00084A, 2692215, ASM36078, EAP4222448, PD00002158, 737534554937, OEM15534663, AP5178218, PS4222448 Compatibility This replacement dishwasher water inlet valve fits select Samsung dishwashers. Common compatible models include (but are not limited to): Samsung DW80F600UTS Samsung DW80J3020US Always verify your dishwasher’s model number before ordering.Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement – Matches OEM fit and water flow performance 💧 Accurate Water Fill Control – Ensures proper water levels for effective cleaning ⚙️ Fixes Common Issues – Resolves no-fill or slow-fill problems 💪 Durable Solenoid Valve – Designed for reliable long-term use 💰 Cost-Effective Repair – Affordable alternative to OEM valves ⚠️ Symptoms If your dishwasher is experiencing any of the following issues, this part may need replacement: ❌ Dishwasher not filling with water 💧 Slow or weak water flow ⚠️ Poor cleaning performance due to low water level 🔄 Cycle not starting properly 🚫 No water entering during wash cycle Replacing this water valve can restore proper dishwasher operation and cleaning efficiency. 📐 Product Specification Part Number: XPDD62-00084A Component Type: Dishwasher Water Inlet Valve Voltage: 120V AC Application: Dishwasher water supply system Mounting: Screw-mounted with hose connection Quality Level: Aftermarket replacement (not OEM) 🛠️ Installation Notes Tools Needed: Phillips screwdriver, adjustable wrench ⚠️ Safety First: Disconnect power and shut off the water supply before servicing the dishwasher. Basic Steps: Turn off power and water supply. Remove the lower access panel. Disconnect water supply line and electrical connector. Remove mounting screws and remove the old valve. Install the new XPARTCO DD62-00084A valve. Reconnect water line and wiring. Restore power and water, then test for leaks and proper filling. ⏱️ Time Required: 20–30 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Aftermarket Appliance Parts 🔄 30-Day Return Policy Restore reliable dishwasher performance — Add to Cart Now for a dependable repair!

Read more less

WPW10308477 Oven Genuine OEM Bake Element Product Overview The WPW10308477 Bake Element is a genuine OEM replacement part engineered for reliable performance in select Whirlpool, Maytag, and KitchenAid ovens. This bake element ensures even and consistent heating inside the oven, helping you achieve perfect baking and roasting results every time. ✅ Genuine OEM Quality✅ Fits Whirlpool, Maytag, KitchenAid Models✅ Delivers Even Heat Distribution✅ Durable and Long-Lasting Parts-O-Matic OFFERS free shipping — always fast, always free! 🔁 Replaces Part Numbers WPW10308477, 9758519, W10308477, 1719751, 3195067, 8053713, 814432, 9758541, WPW10308477VP, AP6019197, PS11752501. Compatible with a wide range of oven models. Not sure if it fits your appliance? Send us your model number — we’re happy to help! 🔥 Restore your oven's performance — get the WPW10308477 Genuine Bake Element from Parts-O-Matic today.

Read more less

ERP WD12X10231 Dishwasher Lower Rack Roller Replaces Part Numbers: WD12X10231, 1263942, AH1481883, EA1481883, AP3994981, PS1481883. Description: This Lower Dishrack Stud and Roller Assembly is a replacement part for select GE dishwasher models. It is essential for the smooth operation of the dishwasher's lower dishrack, allowing it to slide in and out. This assembly includes the roller that attaches to the dishrack and the studs that secure these rollers in place.   This is an aftermarket part that can be used as a replacement for the OEM part.

Read more less

8565925CM Dishwasher Upper Rack Stop Clip Stop clip for upper dishwasher dishrack. Replaces Part Numbers: WP8565925, WPW10508950, 8565925, 8562015, W10508950, 1180483, 8270105, 8524581, 8524582, 8565920, W10082860, W10199682, WPW10082861, W10082861, 1446951, 8270106, AP6014921, PS11748191, AP6013365, PS11746591. Description: This Dishwasher Rack Stop Clip is a replacement part for specific Whirlpool dishwasher models. This small but essential component plays a crucial role in ensuring the smooth and secure operation of the dishwasher racks.   This is an aftermarket part that can be used as a replacement for the OEM part.

Read more less

(2 Pack) WD12X10304 Genuine GE OEM Rack End Cap Clip Replaces Part Number:  WD12X10304, 1556527, WD12X0344, WD12X344, WD30X97, AH2370502, EA2370502, OEM13454003, AP4484666, PS2370502. Description: This Rack Slide End Cap is a Genuine OEM part for specific GE dishwasher models. This small but essential component is designed to secure the end of the rack slide rail, preventing the dish racks from sliding off the track or becoming misaligned.   California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

XPARTCO W11176454 Gas Range Oven Igniter The XPARTCO W11176454 is an aftermarket replacement oven burner igniter compatible with select Whirlpool, Maytag, and Amana gas ranges. The igniter is a hot surface igniter made from silicon carbide that draws electrical current through the oven safety valve to open it, then heats to ignition temperature to light the gas burner. When the igniter weakens or fails, the oven will not heat, will take too long to preheat, or the igniter will glow without lighting the burner. This igniter draws 3.3–3.6 amps at 120V AC and reaches operating temperatures of 1,800°F–3,100°F with a heating time of approximately 17 seconds. The igniter body measures 3-7/10 inches (Length A) with 9-1/2 inch leads and two separate connectors. It directly replaces OEM part numbers W11176454 and W10914411, and is compatible with Whirlpool WFG and WFG505 series, Amana AGR and AGG series, and select Maytag gas range models. Installs in 10–20 minutes with basic hand tools. Quick Answer The XPARTCO W11176454 Gas Range Oven Igniter fixes Whirlpool, Maytag, and Amana gas ovens that won't heat, take too long to preheat, or have an igniter that glows but never lights the burner. Silicon carbide construction. Draws 3.3–3.6A at 120V. Igniter body 3-7/10" with 9-1/2" leads and 2 separate connectors. Replaces W10914411. Common Problems This Part Fixes Oven not heating at all — gas is not igniting Oven takes excessively long to preheat (weak igniter not reaching ignition temperature) Igniter glows orange or red but never lights the gas burner Smell of gas when oven is turned on but burner does not light Oven heats inconsistently or shuts off mid-cycle Clicking sounds from the oven without successful ignition Oven element will not heat despite other components functioning normally Replaces Part Numbers This oven igniter directly replaces the following OEM and cross-reference part numbers: W11176454, 4547416, W10914411, EAP12348439, AWP43029, PD00044759, AP6327293, PS12348439. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This igniter is compatible with select gas ranges from the following brands: Whirlpool gas ranges — WFG320 and WFG505 series (freestanding) Amana gas ranges — AGR and AGG series Maytag gas ranges — select AGR series models Always verify your model number before ordering. Contact our support team if you're unsure. Key Features Hot surface igniter — draws current through the oven safety valve to open it, then ignites the gas burner Silicon carbide construction — superior heat resistance vs. standard ceramic igniters Draws 3.3–3.6 amps at 120V AC — correct range to open the Whirlpool gas safety valve Operating temperature: 1,800°F – 3,100°F with approximately 17-second heat-up time Igniter body length: 3-7/10 inches; lead length: 9-1/2 inches Two separate connectors for easy plug-in installation Directly replaces W11176454 and W10914411 — no modification required Aftermarket replacement built to OEM-equivalent quality standards Quick DIY repair — installs in 10–20 minutes with a screwdriver Product Specifications Part Number W11176454 Also Replaces W10914411 Part Type Oven Burner Igniter (Hot Surface Igniter) Condition Aftermarket Replacement Application Gas Ranges and Ovens Material Silicon Carbide Amperage Draw 3.3 – 3.6 Amps Voltage 120V AC Resistance 40 – 800 Ohms Operating Temperature 1,800°F – 3,100°F Heat-Up Time Approximately 17 seconds Igniter Body Length (A) 3-7/10 inches Lead Length 9-1/2 inches Connectors 2 separate connectors Compatible Brands Whirlpool, Amana, Maytag Installation Notes ⚠️ Gas Appliance Safety Warning This part is used in gas ranges. Working with gas appliances carries risk of gas leaks, fire, and explosion if installed incorrectly. Always shut off the gas supply at the shutoff valve and unplug the range before beginning any repair. If you smell gas at any point during or after installation, leave the area immediately and contact your gas utility provider. If you are not confident working on gas appliances, have this part installed by a qualified appliance technician. ⚠️ Installation Instructions Unplug the range and shut off the gas supply before beginning. Open the oven door and remove the oven racks. Lift and remove the oven bottom panel by unscrewing the retaining screws. Remove the heat shield (if present) to expose the burner and igniter assembly. Unscrew the igniter mounting screws — typically one or two — and carefully disconnect the wire connector. Connect the new W11176454 igniter to the wire harness using the two separate connectors, secure it to the burner bracket with the mounting screws, then reinstall the heat shield and oven bottom panel. Restore gas supply and power and run a test cycle to confirm the oven lights correctly. Important: Do not touch the silicon carbide igniter element with bare hands — oils from skin reduce its lifespan. Handle only by the bracket and leads. Tools needed: Phillips screwdriver, work gloves. Frequently Asked Questions What is the difference between W11176454 and W10914411? The W11176454 is the updated part number that directly supersedes the older W10914411. Both are the same hot surface igniter for compatible Whirlpool, Amana, and Maytag gas ranges. This aftermarket replacement is compatible with both part numbers. How do I know if my oven igniter needs to be replaced? The most common signs are the oven not heating at all, taking much longer than usual to preheat, or the igniter glowing orange but never lighting the burner. A working igniter reaches ignition temperature within about 30–90 seconds and glows bright orange. If it glows dimly or stays on indefinitely without the burner lighting, the igniter has weakened and is no longer drawing enough current to open the gas safety valve. Why does my igniter glow but the oven still won't heat? This is the classic symptom of a weak igniter. The gas safety valve requires a minimum amperage draw — typically around 3.2 amps — to open and allow gas to flow to the burner. As the igniter ages, its resistance increases and amperage drops below this threshold. The igniter still glows because it has some current, but not enough to open the valve. Replacing the igniter resolves this in nearly all cases. Is the W11176454 compatible with my Amana or Maytag range? Yes — the W11176454 is compatible with select Amana AGR and AGG series gas ranges and select Maytag AGR series models in addition to Whirlpool WFG320 and WFG505 series ranges. Always verify your specific model number before ordering to confirm compatibility. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is made from silicon carbide to match the electrical specifications and performance of the original W11176454 igniter. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout  

Read more less

XPARTCO DC47-00018A Dryer Hi Limit Thermostat The XPARTCO DC47-00018A is an aftermarket replacement cycling high-limit thermostat for Samsung and select Kenmore electric dryers. This is a genuine, automatically resetting thermostat — not a one-time fuse. It monitors temperature in the heating circuit and opens to cut power to the heating element at approximately 260°F, protecting the dryer from overheating. Once the temperature drops to around 210°F, it closes again on its own, letting the dryer resume heating without any part replacement needed. This thermostat works alongside a downstream thermal fuse (such as our DC96-00887C listing) in the same overheat-protection circuit. If this thermostat is cycling excessively, tripping prematurely, or failing to regulate temperature correctly, it can put stress on that thermal fuse, sometimes causing it to blow as a last-resort safety measure. Symptoms of a failing high-limit thermostat include no heat or insufficient heat, drying that takes too long, or the dryer shutting off too soon before a load is fully dry. It directly replaces 35001092, WP35001092, 1122485, AP4201898, PS4205217, EAP2430930, PS2430930, and AP6008682. Quick Answer The XPARTCO DC47-00018A Dryer Hi Limit Thermostat fixes Samsung and select Kenmore electric dryers with no heat or insufficient heat, drying that takes too long, or premature shutoff before a load is fully dry. Opens at approximately 260°F, resets automatically around 210°F. Replaces 35001092, WP35001092, 1122485, AP4201898, PS4205217, EAP2430930, PS2430930, AP6008682. This is a resettable thermostat, not a fuse — it does not need replacement after each trip. It's a different component from our DC96-00887C thermal fuse listing, though the two are often checked together. Common Problems This Part Fixes Dryer has no heat or insufficient heat Drying takes too long to complete a cycle Dryer shuts off too soon, before clothes are fully dry Timer will not advance through the cycle Dryer that stopped working suddenly after running unusually hot Dryer with a history of repeated downstream thermal fuse failures Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dryer high-limit thermostat directly replaces the following OEM and cross-reference part numbers: DC47-00018A, AP4201898, T-O-D 60T11, ASM33627, 1122485, PD00002011, PS4205217. WP35001092, 35001092, PD00004704, EAP11741822, AP6008682, AWP47350, PS11741822, L260-50F If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This high-limit thermostat is compatible with select Samsung electric dryers, and also fits select Kenmore dryers built on the Samsung platform, including model numbers such as: DV5471AEW/XAA DV40J3000EW/A2, DV42H5000EW/A3, DV45H7000EW/A2, DV48H7400EW/A2 DV400EWHDWR/AA DVE50M7450W/A3 Note — resettable thermostat, not a fuse: This DC47-00018A is a true cycling thermostat that resets itself automatically. Our DC96-00887C listing, despite frequently being labeled a "thermostat" on other marketplaces, is actually a one-time thermal fuse mounted separately on the blower housing — it cannot reset and must be replaced once blown. The two are different device types serving the same circuit. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Aftermarket replacement cycling high-limit thermostat — automatically resetting, no replacement needed after each trip Opens at approximately 260°F, resets around 210°F Resolves "no heat," "insufficient heat," "takes too long to dry," and "shuts off too soon" symptoms Genuine thermostat, distinct from the downstream thermal fuse in the same circuit No special tools required for installation Replaces 35001092, WP35001092, 1122485, AP4201898, PS4205217, EAP2430930, PS2430930, and AP6008682 Compatible with Samsung and select Kenmore electric dryers Aftermarket replacement built to OEM-equivalent quality standards Product Specifications Part Number XPDC47-00018A OEM Part Number DC47-00018A Part Type Dryer Cycling High-Limit Thermostat Condition Aftermarket Replacement Type Automatically resetting — not a one-time fuse Open Temperature ~260°F Reset Temperature ~210°F Related Component DC96-00887C thermal fuse (blower housing, different device, sold separately) Quantity 1 high-limit thermostat Compatible Brands Samsung, select Kenmore Installation Notes ⚠️ Unplug Dryer Before Starting Disconnect power at the outlet or shut off the circuit breaker before beginning. Wear work gloves. Access is typically through the rear panel, near the heater duct and blower housing area where this thermostat is mounted. Photograph the wiring connections before disconnecting anything, since this thermostat can be positioned close to other similar-looking components in the same circuit. Remove the old thermostat from its mounting position, noting orientation, and disconnect its wiring. Install the new DC47-00018A in the same position, reconnecting wiring exactly as photographed. Reassemble the panel, restore power, and run a full test cycle to confirm normal, consistent heating with no premature shutoffs. Tools needed: Phillips or nut driver (model-dependent), work gloves. Frequently Asked Questions Do I need to reset this thermostat after it trips, or replace it? Neither, in normal operation — this is a genuine cycling thermostat that resets itself automatically once the dryer cools to around 210°F. You should only need to replace it if it has failed outright (stuck open, stuck closed, or no longer switching at the correct temperatures), not simply because it tripped once during normal operation. My dryer shuts off before the load is fully dry. Is that this part? It's a strong possibility. If this high-limit thermostat is tripping prematurely — opening at a lower temperature than it should — the dryer can cut heat and end the cycle early even though the load isn't actually dry yet. This is one of the more common symptoms this thermostat addresses. My thermal fuse keeps blowing. Could this thermostat be the underlying cause? Yes, this is worth investigating. This thermostat and the downstream thermal fuse (our DC96-00887C listing) protect the same circuit at different points. If this thermostat isn't regulating temperature correctly — cycling excessively or failing to catch a temperature spike — the thermal fuse can end up blowing repeatedly as the last line of defense. If you've replaced the fuse more than once, checking or replacing this thermostat at the same time is a reasonable next step. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Samsung OEM part, but is manufactured to match the electrical specifications and opening/reset temperatures of the original DC47-00018A high-limit thermostat used in compatible Samsung and Kenmore electric dryers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

PK136277-2 Lower Dishrack Roller and Axle Set Pack of 2 Replaces: WD12X10136,  WD12X10277   This is an aftermarket part that can be used as a replacement for the OEM part. California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

XPARTCO 50561602 Heater Safety Thermostat  Compatible with Victory 50561602 Safety Switch, Heater, 250F

Read more less

ERP WD12X10277 Dishwasher Lower Dish rack Roller Axle Single Pack Gray Color Replaces Part Number: WD12X10277, WD12X10075, WD12X10101, WD12X10126, WD12X10261   This is an aftermarket part that can be used as a replacement for the OEM part. California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

XPARTCO WE4M137 Dryer High Limit Thermostat The XPARTCO WE4M137 is an aftermarket replacement high limit thermostat for GE, Hotpoint, and Kenmore dryers. Mounted on the upper right side of the heater housing, this safety thermostat monitors the temperature of the heating circuit and cuts power to the heating element (and in some conditions the motor) if the dryer runs hotter than it should — typically from restricted airflow, a clogged vent, or a failing cycling thermostat. Unlike a one-time thermal fuse, this is an auto-resetting high limit thermostat (rated L315-65F): it opens at approximately 315°F to stop overheating, then automatically closes again once the unit cools down, without needing to be replaced after each trip. This is a direct-fit aftermarket replacement built to the same temperature rating and mounting as the original thermostat. If this component trips repeatedly, it's worth checking the underlying cause of the overheating at the same time — a clogged lint trap or restricted exhaust vent is the most common root cause. Quick Answer The XPARTCO WE4M137 High Limit Thermostat fixes a GE, Hotpoint, or Kenmore dryer that shuts off a few minutes into a heat cycle, stops early and won't restart until it cools down, or cycles on and off intermittently. Auto-resetting, rated to open at approximately 315°F. Classic symptom: dryer runs fine for a few minutes then quits on heat, and won't restart again until it's had time to cool. Common Problems This Part Fixes Dryer shuts off a few minutes into a heat-dry cycle Dryer stops early and won't restart until it cools down Intermittent shutdowns during the drying cycle Clothes coming out damp because the cycle keeps cutting short Dryer won't start at all if the thermostat has failed in an open position Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This thermostat directly replaces the following part numbers: WE4M137, WE4M457, 276438, WE04M0137, WE04X25197, 559C131G04, AGE25626, AH267900, AP2042565, EAP267900, EA267900, PD00001228, PS267900 These numbers span several generations of GE's own part numbering for this thermostat as model lines and sub-assemblies were updated — all are the correct replacement for this component regardless of which number appears on your dryer's parts diagram. Compatibility This thermostat is compatible with 28+ GE, Hotpoint, and Kenmore dryer models, including: Kenmore 2661532110, GE 2661532210 Numerous additional GE, Hotpoint, and Kenmore dryer and washer-dryer combo models Note: This thermostat has also been referenced for some Fisher & Paykel dryer applications in sourcing, though we were not able to confirm a specific Fisher & Paykel model list. Confirm your model number against your dryer's parts diagram, or contact our support team to verify fit before ordering. Key Features Direct-fit aftermarket high limit thermostat for GE-built dryers Auto-resetting design — no need to replace after each trip, unlike a one-time thermal fuse Rated to open at approximately 315°F to prevent overheating damage Resolves early-shutoff, won't-restart-until-cool, and intermittent cycling symptoms Fits 28+ GE, Hotpoint, and Kenmore dryer and washer-dryer combo models Straightforward swap — typically 15–30 minutes with basic hand tools Product Specifications Part Number XPWE4M137 OEM Part Number WE4M137 Part Type Dryer High Limit Thermostat (Auto-Reset) Condition Aftermarket Replacement Temperature Rating L315-65F (Opens ~315°F, Auto-Resets on Cooling) Location Upper Right Side of Heater Housing Application GE, Hotpoint & Kenmore Dryers Installation Notes ⚠️ Unplug Power Before Installing Unplug the dryer or switch off its circuit breaker before beginning. Remove the dryer's rear or front panel per your model's service guide to access the heater housing — the thermostat is mounted on its upper right side. Disconnect the wire terminals from the old thermostat, noting their positions, and remove the mounting screw holding it in place. Install the new thermostat in the same position and reconnect the wire terminals. Before closing the dryer back up, clean out the lint trap and check the exhaust vent for restrictions — a clogged vent is the most common cause of this thermostat tripping repeatedly, and clearing it now can prevent a repeat failure. Frequently Asked Questions My dryer shuts off a few minutes into the cycle and won't restart — is this the part I need? Yes, this is a classic symptom of a failing high limit thermostat. It's designed to cut power when the dryer overheats and automatically reset once things cool down, so if your dryer won't restart until it's had time to sit, this thermostat is a likely cause. Is this a one-time fuse like the thermal fuse, or does it reset itself? This is an auto-resetting thermostat, not a one-time thermal fuse. It opens to cut power when the dryer overheats, then closes again automatically once the unit cools — it doesn't need to be replaced every time it trips. If yours has failed and won't reset or close again, that's when replacement is needed. Why does my dryer keep tripping this thermostat? Repeated tripping is usually caused by restricted airflow — a clogged lint trap, a crushed or blocked exhaust duct, or a bird's nest or lint buildup in the outside vent hood — or a failed cycling thermostat elsewhere in the heating circuit. Clear the airflow path when you replace this thermostat, or the new one may trip again. How do I test if this thermostat has failed? With the dryer unplugged, you can test the thermostat with a multimeter for continuity across its terminals at room temperature. No continuity when it should be closed (cool) is a sign it has failed and needs replacement. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less