W11645245 Genuine OEM Whirlpool Refrigerator Dual Water Valve
The W11645245 is a genuine Whirlpool OEM dual water inlet valve for Whirlpool-built refrigerators. Mounted at the rear of the refrigerator where the household water line connects, this single valve is the central control point for water flow to two separate features: the ice maker and the door-mounted water dispenser. When either feature calls for water, this valve's solenoids open to admit it and close again once the request is satisfied — since one valve handles both jobs, a failure here can affect the ice maker, the dispenser, or both at the same time.
Common causes of failure include mineral and sediment buildup from the household water supply interfering with the valve's internal operation over time, and electrical faults either in the valve itself or in the refrigerator's electronic control board that signals it. A failing dual water valve produces a recognizable set of symptoms: the door dispenser stops delivering water, the ice maker slows down, stops producing ice, or fails intermittently, water leaking around the valve area, or an audible electronic buzzing or humming sound coming from the back of the refrigerator. It directly replaces AP7208917, W11546685, W11446818, W11563296, and PS16875686. As a genuine OEM part, the W11645245 is manufactured by Whirlpool to factory specifications — guaranteed fit, materials, and performance.
Quick Answer
The W11645245 Genuine OEM Whirlpool Refrigerator Dual Water Valve fixes Whirlpool-built refrigerators where the door water dispenser stops working, the ice maker slows down or stops making ice, there's a leak near the valve at the back of the refrigerator, or you hear an electronic buzzing or humming sound. Controls water flow to both the ice maker and water dispenser from a single valve. Replaces AP7208917, W11546685, W11446818, W11563296, PS16875686. Before replacing, rule out a simple mineral clog and a faulty control board signal — both can produce identical symptoms to a failed valve.
Common Problems This Part Fixes
Water dispenser on the refrigerator door has stopped working
Ice maker has slowed down, stopped producing ice, or is malfunctioning intermittently
Both the ice maker and water dispenser affected at the same time
Water leaking around the valve area at the back of the refrigerator
Electronic buzzing or humming sound coming from behind the refrigerator
Reduced water flow or pressure at the dispenser
Valve that hums but doesn't appear to be passing water through
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This refrigerator dual water valve directly replaces the following OEM and cross-reference part numbers:
W11546685, W11446818, W11563296, AP7208917, AWP46513, K-79524K, N-86-QC N, PD00080446, PS16875686
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This dual water valve is compatible with select Whirlpool-built refrigerators across the Whirlpool family of brands, including:
Whirlpool refrigerators — WRS series (including WRS321SDHZ08)
Maytag, Jenn-Air, and Amana refrigerators (select models)
KitchenAid, Magic Chef, Admiral, and Norge refrigerators (select models)
Roper refrigerators (select models)
Select Kenmore and Ikea refrigerators built on the Whirlpool platform
Note: This is a dual-function valve serving both the ice maker and water dispenser from a single unit — it is not a hot/cold laundry-style valve pair. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure.
Key Features
Genuine Whirlpool OEM part — factory-specified solenoid design and flow-rate calibration
Dual water inlet valve — controls water flow to both the ice maker and door water dispenser
Resolves "dispenser not working," "ice maker slow or not making ice," "leak near the valve," and "buzzing or humming noise" symptoms caused by valve failure
Single central valve simplifies diagnosis and replacement compared to separate dedicated valves
Direct drop-in replacement — mounts to the original rear connection point
Replaces W11546685, W11446818, W11563296, AP7208917, and PS16875686
Compatible with a wide range of Whirlpool, Maytag, Jenn-Air, Amana, KitchenAid, Magic Chef, Admiral, Norge, Roper, and Kenmore refrigerators
Genuine OEM replacement — guaranteed fit, materials, and performance
Straightforward DIY repair using basic hand tools
Product Specifications
Part Number
W11645245
Part Type
Refrigerator Dual Water Inlet Valve (Ice Maker + Dispenser)
Condition
Genuine OEM
Brand
Whirlpool
Location
Rear of refrigerator, at the household water line connection
Function
Controls water flow to the ice maker and door water dispenser
Connection Type
1/2" water line inlet, NPT threaded
Quantity
1 valve
Compatible Brands
Whirlpool, Maytag, Jenn-Air, Amana, KitchenAid, Magic Chef, Admiral, Norge, Roper, Kenmore
Installation Notes
⚠️ Shut Off Water Supply And Unplug Refrigerator Before Starting — Have A Towel Ready Disconnect power at the outlet, and shut off the water supply valve behind or below the refrigerator before beginning. Wear work gloves. Pull the refrigerator away from the wall for access, then locate the valve at the rear or bottom of the cabinet where the water supply line connects. Have a towel or shallow pan ready, since residual water will spill out when you disconnect the line. Photograph the wiring and water line connections before disconnecting anything. Disconnect the water supply line from the old valve, disconnect the electrical connector, and remove the mounting screws holding it in place, then pull the valve free. Install the new W11645245 in the same position, secure the mounting screws, and reconnect the electrical connector fully. Reattach the water supply line, tightening securely by hand plus a partial turn with pliers — avoid overtightening plastic threaded fittings. Restore the water supply and check the connection for leaks before restoring power. Push the refrigerator back into place, then test both the ice maker and water dispenser over the next day to confirm normal operation has returned. Tools needed: Phillips screwdriver, adjustable wrench or pliers, towel or shallow pan, work gloves.
Frequently Asked Questions
My dispenser stopped working but the ice maker still works. Is this the right part?
It's possible, but worth checking a couple of things first, since this valve serves both features from one unit. Confirm the water supply line isn't kinked or restricted, and check the inline water filter for a clog, since a blocked filter can starve the dispenser specifically while the ice maker (which may draw from a different point in the flow path depending on your model) keeps working. If the filter and supply line are clear and the dispenser still won't deliver water, the valve itself is the likely cause.
I hear a buzzing or humming sound from the back of the fridge. What does that mean?
This is a common symptom of a valve that's receiving an electrical signal to open but isn't passing water through correctly — the solenoid coil energizes and hums, but water flow is restricted or absent, often due to internal mineral buildup or a failing internal mechanism. If you hear this sound whenever the ice maker or dispenser is called on, the valve is a strong suspect.
Could the problem actually be my water filter instead of this valve?
Yes, it's worth ruling out first. A clogged inline water filter can produce very similar symptoms to a failing valve — reduced dispenser flow, slow ice production, or both. Try replacing the water filter first if it's been a while since the last change; if symptoms persist afterward, the dual water valve is the more likely cause.
Could this be a control board issue instead of the valve?
It's possible. This valve is triggered electrically by the refrigerator's control board, so a fault there can produce symptoms that look identical to a failed valve — no water reaching the ice maker or dispenser even though the valve itself is fine. If replacing the valve doesn't resolve the issue, the control board is the next component worth investigating.
Is this an OEM or aftermarket part?
This is a genuine OEM part, manufactured by Whirlpool to factory specifications — guaranteed fit, materials, and performance. It includes the same dual-function solenoid design and connection configuration as the valve originally installed in your refrigerator.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
MSWF Refrigerator Water Filter
Description: This water filter is designed to remove impurities from the water and ice dispensed by your refrigerator, providing clean and fresh-tasting water. It effectively reduces contaminants such as chlorine, lead, mercury, and other particulates, ensuring safe drinking water for you and your family. You should replace this water filter if it becomes clogged or reaches the end of its usable life, typically every six months. Causes of a bad water filter can include normal usage leading to clogging, the accumulation of sediments and impurities over time, or damage to the filter casing. Failing to replace the filter regularly can also compromise its effectiveness.
Replaces Part Number: 1262070, AH1559689, EA1559689, MSWF3PK, WR02X12345, WR02X12801, WR02X13618, AP3997949, PS1559689.
California Residents only
WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov
WR30X39385 Genuine OEM GE Refrigerator Ice Maker
The WR30X39385 is a genuine GE OEM ice maker assembly for GE refrigerators. This complete unit receives water, holds it in an internal mold, and freezes it into cubes, then ejects the finished ice into the freezer's ice bucket or drawer, repeating the cycle automatically until the bucket is full. It's the full assembly, not just an internal component, so replacing it addresses the ice-making mechanism, mold, and cycling controls together as one unit.
Over time, internal components can wear or fail electrically, or the mold itself can develop issues that affect how cleanly ice releases. A failing ice maker typically shows up as reduced or stopped ice production, or ice cubes coming out hollow or malformed rather than solid. It directly replaces AP7179920.
Quick Answer
The WR30X39385 Genuine OEM GE Refrigerator Ice Maker fixes GE refrigerators that have stopped making ice, are producing significantly less ice than usual, or are making hollow or malformed cubes. Complete ice maker assembly. Replaces AP7179920. Installation is a moderate DIY repair, typically 30-45 minutes.
Common Problems This Part Fixes
Ice maker has stopped producing ice entirely
Ice maker producing significantly less ice than usual
Ice cubes coming out hollow or malformed instead of solid
Ice maker cycling but not ejecting cubes into the bucket
Inconsistent ice production from cycle to cycle
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This refrigerator ice maker directly replaces the following OEM and cross-reference part numbers:
WR30X39385, 200D1181G118, 4983508, Model CAN07-018, WR01F04991, AP7179920, EAP16660009, AGE28641, PD00079707, PS16660009
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This ice maker is compatible with select GE refrigerators, and also fits select Hotpoint, Haier, Monogram, and Café refrigerators built on the GE platform.
Note: Always verify your full model number before ordering, since GE uses several different ice maker designs across its refrigerator lineup. Contact our support team with your model number if you're unsure.
Key Features
Genuine GE OEM part — factory-specified mold design and cycling mechanism
Complete ice maker assembly — freezes water into cubes and ejects them automatically
Resolves "not making ice," "reduced ice production," and "hollow or malformed cubes" symptoms
Direct drop-in replacement — no modification required
Replaces AP7179920
Compatible with GE, Hotpoint, Haier, Monogram, and Café refrigerators
Genuine OEM replacement — guaranteed fit, materials, and performance
Moderate DIY repair, typically 30-45 minutes
Product Specifications
Part Number
WR30X39385
Part Type
Refrigerator Ice Maker Assembly
Condition
Genuine OEM
Brand
GE
Function
Freezes water into cubes and ejects them automatically into the ice bucket/drawer
Repair Difficulty
Moderate — 30 to 45 minutes
Quantity
1 ice maker assembly
Compatible Brands
GE, Hotpoint, Haier, Monogram, Café
Installation Notes
⚠️ Unplug Refrigerator Before Starting — Allow Components To Defrost Disconnect power to the refrigerator before beginning, and move perishable food to a cooler for the duration of the repair. Wear work gloves. If there's frost or ice buildup around the ice maker or its fill tube, allow the area to defrost fully before continuing, since ice buildup can make removal difficult and may mask the fill tube's actual condition. Open the freezer door and locate the ice maker assembly. Remove the ice bucket or drawer to improve access. Photograph the wiring harness connection and the fill tube position before disconnecting anything. Remove the mounting screws securing the ice maker in place, then disconnect the wire harness connector and the water fill tube connection. Remove the old ice maker fully. Install the new WR30X39385 in the same mounting position, making sure the fill tube aligns correctly so water reaches the mold without leaking, and reconnect the wire harness connector securely. Secure the mounting screws, reinstall the ice bucket or drawer, and restore power. Allow several hours for the first cycle to complete and confirm ice is being produced and ejected normally. Tools needed: Phillips screwdriver, work gloves.
Frequently Asked Questions
My ice cubes are coming out hollow. Is that the ice maker?
Yes, hollow or malformed cubes are a documented symptom of ice maker issues on this platform, alongside reduced or stopped ice production altogether. This can point to a problem with how the mold fills or releases ice, and replacing the complete assembly addresses the mold and cycling mechanism together rather than trying to diagnose and repair individual internal components.
Why does the fill tube alignment matter so much during installation?
The fill tube is what delivers water from the refrigerator's supply line into the ice maker's mold at the start of each cycle. If it's not aligned correctly during installation, water can miss the mold, leak into the freezer compartment, or fail to fill the mold completely, all of which prevent normal ice production even with a perfectly good new ice maker installed.
Do I need to defrost anything before starting this repair?
If there's visible frost or ice buildup around the old ice maker or its fill tube, yes — letting that area defrost fully makes removal easier and gives you a clearer look at the fill tube's actual condition, rather than working around ice that could mask damage or make the old unit harder to detach cleanly.
Is this an OEM or aftermarket part?
This is a genuine OEM part, manufactured by GE to factory specifications — guaranteed fit, materials, and performance. It includes the same mold design, cycling mechanism, and mounting configuration as the ice maker originally installed in your refrigerator.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
WR57X30890 Refrigerator Genuine Water Valve
Water inlet valve assembly with Wire Harness
Replaces Part Numbers: WR57X30890, WR57X26569, WR57X30891, AP6891693, PS12727426.
Description: This water inlet valve is a Genuine OEM part for select GE Refrigerator models, responsible for controlling the flow of water into the refrigerator's ice maker and water dispenser. It is typically located at the back of the appliance, near the water supply line. The water inlet valve features quick-connect fittings for easy installation and ensures a reliable and steady supply of water for ice production and dispensing.
XPARTCO DA31-00342A Refrigerator Evaporator Fan Motor - Compatible with Samsung Refrigerators
Product Description
Restore optimal cooling in your refrigerator with the replacement DA31-00342A Refrigerator Evaporator Fan Motor. This high-quality replacement evaporator fan motor, designed for Samsung refrigerators, circulates chilled air through the fresh food and freezer compartments to maintain even temperatures. Constructed from durable plastic with sticky insulation and a silent sponge for quiet operation, this DC motor (12V, 4.2W, 0.35A, 1850 RPM) addresses issues like temperature fluctuations, frost buildup, or noisy operation.
Note: Includes one evaporator fan motor with 3-pin connector and 60cm wire;. Disconnect power before installation.
Replaces part numbers: DA31-00342A, EAP12590899, 4982090, ARES2130RA, PD00080451, EAP12590899, AP6803165, PS12590899
Compatibility:
Compatible with models including but not limited to:
Samsung: DA31-00342A Refrigerator FAN is the correct replacement for model numbers. RM80F22WEWAA RM70F22NERAA RM80F23VMRAA RF32CG5B10SRAA RF27CG5B10SRAA DRZ30980RAP/DA DRZ30980LAP/DA DRZ36980RAP/DA DRZ36980LAP/DA RQ48T9432T1/AA RS28A5F61SG/AA RS27T5202SR/AA RQ48T94B277/AA RS28A500ASR/AA RS28A500ASG/AA RS22T5561SR/AA RF32CG5N10SRAA RS27T5200WW/AA RS23A500ASG/AA RS28A5F61SR/AA RF32CG5900MTAC RS23CB7600QLAA RF32CG5900SRAA RF27CG5900SRAA RF32CG5100SRAA RF26CG7400SRAA RF27CG5400SRAA RF32CG5400MTAA RF31CG7400MTAA RF27CG5100SRAA RS23CB760012AA RF31CG7200SRAA RF32CG5100MTAA RF27CG5010S9AA RF32CG5400SRAA RF32CG5300SRAA RS28CB7600QLAA RS28CB760012AA RF31CG7400SRAA RF31CG7220SRAA DRZ36980RAP/DA DRZ30990LAP/DA DRZ30980RAP/DA DRZ36980LAP/DA DRZ30990RAP/DA DRZ30980LAP/DA RS22T5561SG/AA RS27T5561SG/AA RS23A500ASR/AA RS27T5561SR/AA RS27T5201SR/AA RS27T5200SR/AA RS22T5561SR RS27T5200SG/AA RS22T5201SR/AA
Verify your model number or contact our support team for assistance.
Key Features:
✅ Brand and Models Compatibility: Fits select Samsung refrigerator models.
🔥 Specifications: replacement evaporator fan motor, DC 12V, 4.2W, 0.35A, 1850 RPM, 3-pin connector, 60cm/23.62" wire length, 5.3" fan diameter, plastic construction with sticky insulation and silent sponge for quiet operation.
💰 Cost-Effective Alternative: replacement motor offers OEM-equivalent performance at a lower price.
🛠️ Easy Installation: Requires a Phillips screwdriver, work gloves; typically installed in 30–60 minutes.
🛡️ Reliable Fixes: Resolves poor cooling, frost buildup, noisy operation (grinding or buzzing), or evaporator coil freezing.
Installation Notes:
Safety First: Disconnect the refrigerator from the power source before installation.
Shop Parts-O-Matic for high-quality replacement appliance parts with a 30-day return policy. Keep your refrigerator cooling efficiently today!
Add to cart now for a budget-friendly fix!
Genuine Refrigerator Replacement Part
DA97-14992A Refrigerator Genuine Auto-Close Lever
Genuine auto-close lever for select refrigerator door hinge and closure systems.
Product Overview
The DA97-14992A Refrigerator Auto-Close Lever is a genuine replacement part designed for compatible refrigerators. The lever works with the door hinge and closure mechanism to help guide the refrigerator door into the proper closed position.
Use this part when the original lever is cracked, worn, broken, loose, or no longer helping the door close correctly.
Quick Answer
DA97-14992A is a genuine refrigerator auto-close lever for compatible door closure assemblies. Replace it when the original lever is damaged or the door no longer closes and aligns as intended.
Common Problems This Part May Fix
Refrigerator door does not close smoothly
Door does not pull fully into the closed position
Auto-close action is weak or inconsistent
Lever is cracked, broken, or worn
Door alignment changes near the closed position
Replaces and Cross-References
DA97-14992A, 3974211, AP5915404, ASM138875, EAP9604575, PD00039402, PS9604575
Part number is provided for identification. This listing is for a genuine replacement part.
Compatibility
Fits select refrigerators that specify auto-close lever part number DA97-14992A.
Important: Verify the complete refrigerator model number, door position, and original lever part number before ordering. Similar-looking hinge and closure components may differ by model or door side.
Key Features
Genuine replacement part
Designed for compatible refrigerator door closure systems
Helps guide the door into the closed position
Supports proper door alignment near closing
Direct replacement for applications calling for DA97-14992A
Product Specifications
Part Number
DA97-14992A
Part Type
Refrigerator Auto-Close Lever
Application
Compatible Refrigerator Door Systems
Function
Assists door closing and alignment
Condition
New
Part Quality
Genuine Replacement Part
Package Quantity
1 Auto-Close Lever
Installation & Troubleshooting Notes
Disconnect refrigerator power before service.
Support the door if hinge or closure hardware must be loosened or removed.
Inspect the original auto-close lever for cracks, wear, deformation, or looseness.
Check nearby hinge and closure components for related wear or damage.
Install the replacement lever in the same position and orientation as the original.
Confirm the door opens, aligns, and closes smoothly before returning the refrigerator to normal use.
Diagnostic tip: A door that does not close correctly may also have worn hinges, loose mounting hardware, cabinet leveling issues, or gasket interference. Inspect the full door system before replacing only the lever.
Frequently Asked Questions
What does DA97-14992A do?
It works with the refrigerator door closure system to help guide the door into the proper closed position.
Is DA97-14992A a genuine part?
Yes. This listing is for a genuine refrigerator auto-close lever.
When should this lever be replaced?
Replace it if it is cracked, broken, excessively worn, loose, or no longer supporting proper door closing.
Will this fit every refrigerator?
No. Match the complete refrigerator model number, door position, and original part number before ordering.
Shop With Confidence
Verify your complete refrigerator model number before purchasing. Our compatibility team can help confirm whether DA97-14992A is correct for your appliance.
Genuine ReplacementDoor Closure PartModel Fitment SupportFast U.S. Shipping
XPARTCO W10464673 Refrigerator Evaporator Fan Motor Replaces WPW10464673
The XPARTCO W10464673 is an aftermarket replacement refrigerator evaporator fan motor compatible with select Whirlpool, KitchenAid, Maytag, Kenmore, and Ikea bottom-freezer and French door refrigerators. The evaporator fan motor is located inside the freezer compartment and circulates cold air from the evaporator coils throughout both the freezer and fresh food sections. Without the evaporator fan running, cold air cannot be distributed — even if the compressor and evaporator are working correctly, both compartments will gradually warm up. A failed evaporator fan motor is one of the most common causes of a refrigerator that runs but does not cool.
Rated 115V, 60Hz with a 2-pin connector, this motor features a 14mm shaft length, 3mm shaft diameter, and approximately 13cm (5.1") of wire lead. It is constructed from ABS plastic housing with a metal motor core. It directly replaces WPW10464673, 3020513, AP6021839, PS7320664, PS11755167, and EAP11755167. Compatible models include KitchenAid KFFS and KRFF series, Maytag MFB and MFF series, and several Kenmore 106/596-series models. Installs in 20–30 minutes with basic hand tools.
Quick Answer
The XPARTCO W10464673 Refrigerator Evaporator Fan Motor fixes refrigerators where both compartments are too warm, the refrigerator runs but doesn't cool, or there is unusual noise from inside the freezer. 115V/60Hz, 2-pin connector, 14mm shaft, 3mm shaft diameter, 13cm leads. ABS/metal construction. Compatible with KitchenAid KFFS/KRFF, Maytag MFB/MFF, Whirlpool, and Kenmore 106/596-series. Replaces WPW10464673, 3020513, AP6021839, PS7320664, PS11755167.
Common Problems This Part Fixes
Both refrigerator and freezer compartments too warm — evaporator fan not circulating cold air
Refrigerator running continuously but not cooling — compressor on but no air circulation
Freezer section cold but fresh food section warm — fan not moving air between compartments
Unusual buzzing, squealing, or grinding noise coming from inside the freezer
No airflow felt inside the refrigerator or freezer when the compressor is running
Fan blade visible inside the freezer but not spinning when the compressor runs
Ice buildup on the evaporator coils causing the fan blade to stop
Replaces Part Numbers
This evaporator fan motor directly replaces the following OEM and cross-reference part numbers:
WPW10464673, W10464673, 3020513, AWP50481, EAP11755167, PD00030978, AP6021839, PS11755167, FDQC16WP2A.
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This evaporator fan motor is compatible with select refrigerators from the following brands and series:
KitchenAid refrigerators — KFFS20 and KRFF300 series (KFFS20EYMS02, KFFS20EYBL02, KFFS20EYBL04, KRFF300EBL00, KRFF300EBS00 and related models)
Maytag refrigerators — MFB2055 and MFF2055 series (MFB2055YEB01, MFB2055YEB02, MFB2055YEM01, MFB2055YEM02, MFB2055YEW02, MFF2055DRE00, MFF2055YEB02, MFF2055YEW00, MFW2055FRH00, MFB2055FRW00 and related models)
Whirlpool refrigerators (select bottom-freezer and French door models)
Kenmore / Sears refrigerators — 106 series and 596 series (10673002510, 10673002511, 10673003510, 10673003511, 59673002510, 59673003510, 59673003511, 59673009510, 10679472411, 10679473411 and related models)
Ikea refrigerators (select models)
Always verify your appliance model number before ordering. Contact our support team if you're unsure.
Key Features
Circulates cold air from the evaporator coils throughout the freezer and fresh food compartments — essential for maintaining set temperatures in both sections
115V, 60Hz — correct electrical specifications for compatible models
2-pin connector — direct plug-in replacement on compatible models
Shaft: 14mm length, 3mm diameter — matches original motor shaft dimensions for fan blade compatibility
Wire lead length: approximately 13cm (5.1 inches)
ABS plastic housing with metal motor core — durable and designed for continuous freezer-temperature operation
Replaces WPW10464673, 3020513, AP6021839, PS7320664, PS11755167, and FDQC16WP2A
Compatible with KitchenAid KFFS/KRFF, Maytag MFB/MFF, Kenmore 106/596, Whirlpool, and Ikea refrigerators
Aftermarket replacement built to OEM-equivalent quality standards
DIY repair — installs in 20–30 minutes with basic hand tools
Product Specifications
Part Number
W10464673
OEM Part Number
WPW10464673
Part Type
Refrigerator Evaporator Fan Motor
Condition
Aftermarket Replacement
Application
Bottom-Freezer and French Door Refrigerators
Voltage
115V AC
Frequency
60 Hz
Connector
2-pin plug
Shaft Length
14mm (0.55 inches)
Shaft Diameter
3mm (0.12 inches)
Wire Lead Length
Approximately 13cm (5.1 inches)
Material
ABS plastic housing / Metal motor core
Compatible Brands
Whirlpool, KitchenAid, Maytag, Kenmore, Ikea
Installation Notes
⚠️ Unplug Refrigerator and Shut Off Water Before Starting Unplug the refrigerator and shut off the water supply before beginning. Remove all food and shelving from the freezer compartment. On most compatible models, the evaporator fan is located behind the freezer back panel. Remove the screws securing the freezer back panel and carefully slide it out to expose the evaporator coils and fan assembly. If ice has built up on the fan or coils, use a hair dryer to melt it before attempting to remove the fan — do not force a frozen fan free. Disconnect the 2-pin wire connector from the old motor. Remove the fan blade by pulling it straight off the motor shaft, then unscrew the motor mounting brackets and remove the old motor. Install the new W10464673 motor in the same position, secure the mounting brackets, press the fan blade back onto the shaft, and reconnect the 2-pin connector. Reinstall the freezer back panel, restore power and water, and verify the fan runs when the compressor starts. Tools needed: Phillips screwdriver, hair dryer (if coils are iced), work gloves.
Frequently Asked Questions
What does the evaporator fan motor do?
The evaporator fan motor drives a fan blade inside the freezer compartment that draws air across the evaporator coils — the cold coils remove heat from the air, and the fan distributes the chilled air throughout both the freezer and fresh food sections via a duct system. Without the evaporator fan running, the evaporator coils still get cold and the compressor still runs, but no cold air is circulated. This causes both compartments to gradually warm up even though the refrigeration system itself may be functioning correctly. A failed evaporator fan motor is one of the most common and most frequently misdiagnosed causes of poor refrigerator cooling.
How do I know if the evaporator fan motor has failed?
Open the freezer door and press the door switch (the small button or tab that tells the refrigerator the door is closed) — this should start the evaporator fan if the compressor is running. If you hear no fan noise and feel no airflow from inside the freezer with the compressor running, the fan motor has likely failed. You can also remove the freezer back panel and physically check whether the fan blade spins freely by hand — if it is stuck or wobbles, inspect for ice buildup or a seized motor bearing. If the blade spins freely but the motor does not run when powered, the motor has burned out.
What is the difference between W10464673 and WPW10464673?
These are the same evaporator fan motor. WPW10464673 is the updated Whirlpool OEM part number that superseded the original W10464673. The 3020513 is also a cross-reference for this same motor. This aftermarket replacement is compatible with all of these numbers.
My freezer is cold but my fridge is warm — could it be the evaporator fan?
Yes — this is a classic evaporator fan failure symptom. When the fan motor fails partially, the freezer may still receive some cold air passively from the evaporator, but not enough air is circulated to reach the fresh food section through the duct system. A failed evaporator fan is frequently the cause of this hot-fridge-cold-freezer pattern. Check the fan as described above — if it is not spinning, replacing the W10464673 motor will restore cooling to both compartments.
Is this an OEM or aftermarket part?
This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured from ABS plastic and metal to match the electrical specifications and shaft dimensions of the original W10464673 evaporator fan motor.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout
5304530651 Refrigerator Genuine OEM Evaporator Fan Motor
115V 60hz 2.8W
Replaces Part Numbers: 5304530651, 242077704, AP7179350, PS16660872
Description: This Evaporator Fan Motor is a Genuine OEM part for specific Electrolux, Frigidaire refrigerator models. It is responsible for circulating air throughout the refrigerator’s interior to maintain consistent cooling and optimal temperature distribution. This motor works to move air over the evaporator coils, aiding in the cooling process and ensuring that the refrigerator and freezer compartments remain at the desired temperature.
WF1CB Refrigerator Water Filter
Description: This water filter is designed to remove impurities from the water and ice dispensed by your refrigerator, providing clean and fresh-tasting water. It effectively reduces contaminants such as chlorine, lead, mercury, and other particulates, ensuring safe drinking water for you and your family. You should replace this water filter if it becomes clogged or reaches the end of its usable life, typically every six months. Causes of a bad water filter can include normal usage leading to clogging, the accumulation of sediments and impurities over time, or damage to the filter casing. Failing to replace the filter regularly can also compromise its effectiveness.
Replaces Part Numbers: WFCB, WF1CB, 218670303, 218710901, 218710902, 218717805, 218904602, 240389101, 240389102, 240394501, 242007903, 277187, 5303917752, 5303917836, 5303917937, 5303918017, 5304461598, 9906, 9906P, 9910, AH503627, EA503627, FRWFCB, AP2591529, PS503627, RC-101, RC-200, RC101, RC200, RENEW1CB, RENEWFCB, RG100, WF1CB-, WFB, WFCB-
XPARTCO WR60X10307 Refrigerator Evaporator Fan Motor
The XPARTCO WR60X10307 is an aftermarket replacement evaporator fan motor designed to circulate cold air throughout the refrigerator and freezer compartments. Restore efficient cooling with the replacement XPARTCO WR60X10307 Refrigerator Evaporator Fan Motor. This evaporator fan motor is designed for select GE, Hotpoint, RCA, and Kenmore refrigerators, circulating air over the evaporator coils to maintain consistent temperatures in both refrigerator and freezer compartments. It includes a 6-pin harness with a 2-wire thermistor, addressing issues like noisy operation, inconsistent temperatures, or frost buildup, offering a cost-effective alternative to OEM parts.
When the fan motor fails, cold air cannot circulate effectively, leading to warm refrigerator sections, frost buildup, or noisy operation. Replacing the evaporator fan motor restores airflow, improves cooling efficiency, and helps prevent food spoilage.
Quick Answer
The XPARTCO WR60X10307 Evaporator Fan Motor fixes refrigerators that are not cooling properly, have warm fresh food sections, or make unusual buzzing or grinding noises. It restores proper air circulation inside the unit.
Common Problems This Part Fixes
Refrigerator not cooling properly
Freezer cold but fridge section warm
Loud buzzing, humming, or grinding noise
Frost buildup around evaporator coils
Inconsistent temperature between compartments
No airflow from vents
Replaces Part Numbers
This evaporator fan motor replaces the following part numbers:
WR60X10307, WR60X10099, WR60X10224, WR60X30370, 197D4968G009, FDQT26GE6, AGE29301, PD00001317, EAP2364950, AP4438809, 1550741, PS2364950
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This evaporator fan motor is compatible with select refrigerators from the following brands:
GE refrigerators
Hotpoint refrigerators
Other compatible models using WR60X10307
Always verify your refrigerator’s model number before ordering. Contact our support team if you’re unsure.
Key Features
Circulates cold air across evaporator coils
Restores proper airflow and temperature balance
Offers OEM-equivalent performance at a lower price.
Reduces noise from worn or failing fan motors
Improves overall cooling efficiency
Direct replacement for WR60X10307 motor, evaporator fan motor, 9.75V DC, 3.25W, includes 6-pin harness with 2-wire thermistor.
Product Specifications
Part Number
XPARTCO WR60X10307
Part Type
Evaporator Fan Motor
Application
Refrigerator / Freezer
Condition
Aftermarket Replacement
Function / Specs
Air Circulation, 9.75V DC, 3.25W
Compatible Brands
GE, Hotpoint
Installation Notes
⚠️ Safety First — Disconnect Power Before Service Unplug the refrigerator before servicing. Access the evaporator fan by removing the rear freezer panel. Disconnect wiring harness and mounting screws, replace the fan motor, and reassemble. Ensure the fan spins freely before restoring power.
Frequently Asked Questions
What does the evaporator fan motor do?
It circulates cold air from the evaporator coils throughout the refrigerator and freezer compartments to maintain even cooling.
Will this fix a warm refrigerator section?
Yes, a failed evaporator fan motor is a common cause of warm fridge sections while the freezer remains cold.
Is this an OEM part?
This is a high-quality aftermarket replacement built to OEM-equivalent standards for reliable performance.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in high-quality replacement parts. Fast shipping from our U.S. warehouse and expert support available to help verify compatibility.
✓ Fast US Shipping ✓ Quality Parts ✓ Compatibility Support ✓ Secure Checkout
XPARTCO 2315539 Refrigerator Evaporator Fan Motor Replaces WP2315539
The XPARTCO 2315539 is an aftermarket replacement refrigerator/freezer evaporator fan motor compatible with a wide range of Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Roper, Crosley, Admiral, Estate, Inglis, Ikea, and Gladiator refrigerators. The evaporator fan motor is located in the freezer section and circulates air across the evaporator coils — the cold air generated at the coils is then pushed throughout the freezer and the fresh food compartment. When this motor fails, the most common symptom is excessive noise from the freezer area, and often the refrigerator section won't cool properly even though the freezer remains cold.
This motor includes the incorporated wire harness and plug. Rated 115V, 60Hz, with clockwise rotation. It directly replaces WP2315539, WP2315539VP, 2219689, 2225625, W10438708, 1372146, 1518337, AP3996841, AP6007247, ESF-U2B, EAP11740359, PD00021608, PS11740359, and PS1518337. Important: don't forget to transfer the two rubber grommets from your old motor to the new one for proper mounting. Installs in 30–45 minutes with basic hand tools.
Quick Answer
The XPARTCO 2315539 Refrigerator Evaporator Fan Motor fixes Whirlpool, Kenmore, Maytag, KitchenAid, and Amana refrigerators with excessive noise from the freezer area, ice buildup in the freezer, or where the fresh food section is warm but the freezer is still cold. Includes incorporated wire harness and plug. 115V, 60Hz, clockwise rotation. Transfer rubber grommets from old motor for mounting. Replaces WP2315539, WP2315539VP, 2219689, 2225625, W10438708, 1372146, AP3996841, AP6007247, ESF-U2B, EAP11740359, PS11740359, PS1518337.
Common Problems This Part Fixes
Excessive noise from the freezer area — most common symptom of evaporator fan motor failure
Loud humming, whining, grinding, or scraping noises during operation
Freezer compartment cold but fresh food section warm — cool air not being circulated
Heavy ice buildup on the evaporator coils or rear freezer wall
Refrigerator running continuously trying to maintain temperature
Fan blade not spinning freely or seized when checked by hand
Motor failing continuity test with a multimeter
Visible damage to the fan motor housing or harness
Replaces Part Numbers
This evaporator fan motor directly replaces the following OEM and cross-reference part numbers:
WP2315539, 2315539, W10438708, 1372146, 2219689, 2225625, ESF-U2B, AP6007247, AWP47336, EAP11740359, PD00003243, PS11740359.
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This evaporator fan motor is compatible with select refrigerators from the following brands:
Whirlpool refrigerators (top-mount, side-by-side, and Gold series — select models)
Kenmore / Sears refrigerators (Whirlpool-built — select 106-series and related models)
Maytag refrigerators (select models)
KitchenAid refrigerators (select models)
Amana refrigerators (select models)
Roper refrigerators (select models)
Crosley refrigerators (select models)
Admiral refrigerators (select models)
Estate refrigerators (select models)
Inglis refrigerators (select models)
Ikea refrigerators (select Whirlpool-built models)
Gladiator refrigerators (select models)
Note: This motor includes an incorporated wire harness. If your old motor has a separate wire harness (not incorporated), confirm the correct part with our support team before ordering. Always verify your model number first. Remember to transfer the two rubber grommets from your old motor to the new one — they're essential for proper mounting.
Key Features
Refrigerator/freezer evaporator fan motor — circulates cold air from the evaporator coils throughout both the freezer and fresh food compartments
Includes incorporated wire harness and plug — direct plug-in installation
Rated 115V, 60Hz — correct electrical specifications for compatible Whirlpool-platform refrigerators
Clockwise motor rotation
Replaces WP2315539, WP2315539VP, 2219689, 2225625, W10438708, 1372146, AP3996841, AP6007247, ESF-U2B, PS11740359, PS1518337, and additional cross-references
Compatible with Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Roper, Crosley, Admiral, Estate, Inglis, Ikea, and Gladiator refrigerators
Important: transfer the two rubber grommets from the old motor to the new one for proper mounting
Aftermarket replacement built to OEM-equivalent quality standards
DIY repair — installs in 30–45 minutes with basic hand tools
Product Specifications
Part Number
2315539
OEM Part Number
WP2315539
Part Type
Refrigerator Evaporator Fan Motor (Freezer Section)
Condition
Aftermarket Replacement
Application
Refrigerators (Whirlpool platform)
Voltage
115V AC
Frequency
60 Hz
Rotation
Clockwise
Wire Harness
Incorporated wire harness and plug included
Mounting
Transfer two rubber grommets from old motor
Compatible Brands
Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Roper, Crosley, Admiral, Estate, Inglis, Ikea, Gladiator
Installation Notes
⚠️ Unplug Refrigerator and Move Perishable Food Before Starting — Wear Work Gloves Unplug the refrigerator and safely store any food that could spoil while the power is off. Wear work gloves to protect your hands. The evaporator fan motor is located behind the rear access panel inside the freezer compartment. Remove the freezer shelves and any internal components blocking access to the rear panel. Remove the screws holding the rear access panel to expose the evaporator coils and fan motor (a 1/4" hex driver is commonly needed). Photograph the wire connections and fan blade orientation before disconnecting. Disconnect the wire harness connector from the old motor. Note the orientation of the fan blade on the motor shaft and the position of the two rubber mounting grommets — both must be transferred to the new motor. Remove the mounting screws or release the motor from its bracket, and pull the old motor free. Transfer the rubber grommets and fan blade (if not pre-installed) to the new 2315539 motor in the same orientation. Install the new motor in the same position, reconnect the wire harness, and reinstall the access panel and shelves. Plug the refrigerator back in and allow several hours for the unit to return to its set temperature before reloading with food. Tools needed: 1/4" hex driver, Phillips screwdriver, flathead screwdriver, work gloves.
Frequently Asked Questions
My freezer is making loud noise — is it the evaporator fan motor?
Yes, this is the most recognizable symptom of a failed evaporator fan motor on Whirlpool-platform refrigerators. When the motor's bearings wear out, it produces loud humming, whining, grinding, or scraping noises during operation. The noise often varies as the fan speed changes or as ice builds up around the fan blade. To confirm, unplug the refrigerator and access the fan behind the rear freezer panel — try turning the blade by hand. If it doesn't spin freely, is stiff, or seizes, the motor bearing has failed and needs replacement.
My freezer is cold but my fridge is warm — could this be the cause?
Yes — on many Whirlpool-platform refrigerators, the freezer's evaporator fan motor is responsible for circulating cool air from the freezer evaporator into the fresh food compartment as well. When this fan fails, the freezer's own compartment may stay cold because the cold air is generated right there, but the fresh food section warms up because no air is being moved into it. If your fridge is warm while the freezer remains cold, this is a likely cause — especially if you also hear unusual noise from the freezer area or see ice buildup on the evaporator coils.
What is the difference between 2315539 and WP2315539?
These are the same evaporator fan motor. WP2315539 is the updated Whirlpool OEM part number that superseded the original 2315539. The 2219689, 2225625, W10438708, and ESF-U2B are also cross-references for this same motor across various Whirlpool catalog revisions and production runs. This aftermarket replacement is compatible with all of these numbers.
Why do I need to transfer the rubber grommets from the old motor?
The two rubber grommets seat between the motor housing and the mounting bracket inside the refrigerator. They isolate the motor from the cabinet to dampen vibration and reduce noise during operation, and they also keep the motor properly positioned in its mount. The new 2315539 typically ships without these grommets — they are reused from the old motor. Remove them carefully from the old motor before discarding it, and slide them onto the new motor in the same positions. Without the grommets, the motor may run noisily or vibrate excessively.
Is this an OEM or aftermarket part?
This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured to match the dimensions, electrical specifications (115V AC, 60Hz, clockwise rotation), incorporated wire harness, and function of the original WP2315539/2315539 evaporator fan motor.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout
