Search results for "washer drain pumps"

WD21X25468 Genuine OEM GE Dishwasher Pressure Sensor Assembly The WD21X25468 is a Genuine OEM GE replacement dishwasher pressure sensor assembly compatible with a wide range of GE, GE Profile, GE Café, Hotpoint, Haier, and Monogram dishwashers in the GDF, GDT, GDP, PDT, CDT, ZDT, QDP, and HDF series. The pressure sensor monitors water pressure inside the dishwasher tub during fill and drain cycles and sends real-time readings to the electronic control board. The control board uses these readings to calculate the correct amount of water needed for each wash cycle and to confirm that the tub has drained properly before advancing to the next cycle phase. When the pressure sensor fails — or when it becomes clogged with grease, food residue, or mineral buildup — the dishwasher may not fill with water, may overfill, may stop mid-cycle, may fail to drain correctly, or may display error codes H2O or FTD (Failure to Drain). This Genuine OEM part is manufactured by GE to factory specifications. It directly replaces AP6976524, PS12741258, EAP12741258, 4962334, 37640602, and 265D3356P001. Sold individually. Installs in 15–20 minutes — a screwdriver is the only tool required for most models. Quick Answer The WD21X25468 Genuine OEM GE Dishwasher Pressure Sensor Assembly fixes GE dishwashers displaying error codes H2O or FTD (Failure to Drain), not filling with water, overfilling, stopping mid-cycle, or running excessive noise from the spray arms. Monitors water level and pressure — signals the control board to fill, wash, and drain correctly. Genuine OEM. Replaces AP6976524, PS12741258, EAP12741258, 4962334, 37640602, 265D3356P001. Sold individually. Compatible with GE GDF, GDT, PDT, CDT, ZDT, QDP, HDF, and related series. Common Problems This Part Fixes Error code H2O displayed — dishwasher not receiving enough water or no water at all Error code FTD (Failure to Drain) displayed — sensor not confirming tub has drained Dishwasher not filling with water when a cycle is started Dishwasher overfilling — sensor not signaling the control board to stop filling Dishwasher stopping mid-cycle without completing the wash Excessive noise during operation — sensor not accurately controlling spray arm water pressure Dishwasher requires priming with water to start (filling the tub manually before it will run) Replaces Part Numbers This pressure sensor directly replaces the following OEM and cross-reference part numbers: WD21X25468, 265D3356P001, AGE24772, AP6976524, EAP12741258, OEM20929581, PD00067609, PS12741258. Contact our support team with your model number if you need confirmation before ordering. Compatibility This pressure sensor is compatible with a wide range of dishwashers from the following GE product lines: GE dishwashers — GDF450, GDF510, GDF511, GDF535, GDF550, GDF565, GDF570, GDF630, GDF640, GDF645 series GE dishwashers — GDT530, GDT535, GDT565, GDT580, GDT605, GDT625, GDT630, GDT635, GDT645, GDT695 series GE dishwashers — GDP615, GDP645, GDP665 series GE Profile dishwashers — PDT715, PDT775, PDT785 series GE Café dishwashers — CDT800, CDT875 series GE Monogram dishwashers — ZDT800, ZDT870, ZDT925, ZDT985 series Hotpoint dishwashers — HDF310, HDF330 series Haier dishwashers (select GE-platform models) GE / Café / Profile — QDP555 series Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Genuine OEM part manufactured by GE to factory specifications — guaranteed fit and performance Monitors water pressure inside the tub throughout fill and drain cycles — signals the control board to fill to the correct level and confirm complete drainage Resolves H2O and FTD error codes on compatible GE dishwashers Sensor can also fail due to grease or mineral buildup blocking the pressure port — cleaning may resolve the issue without replacement Replaces AP6976524, PS12741258, EAP12741258, 4962334, 37640602, and 265D3356P001 Compatible with GE GDF, GDT, GDP, PDT, CDT, ZDT, QDP, HDF, and Hotpoint dishwasher series Sold individually Quick DIY repair — installs in 15–20 minutes with a screwdriver Product Specifications Part Number WD21X25468 Part Type Dishwasher Pressure Sensor Assembly (Pressure Switch) Condition Genuine OEM Application GE, GE Profile, GE Café, GE Monogram, Hotpoint, Haier Dishwashers Function Monitors tub water level and pressure — signals control board for fill and drain control Error Codes Resolved H2O (no/low water), FTD (Failure to Drain) Sold As Single sensor assembly Compatible Brands GE, GE Profile, GE Café, GE Monogram, Hotpoint, Haier Installation Notes ⚠️ Unplug Dishwasher and Shut Off Water Before Starting Disconnect power and shut off the water supply before beginning. On most compatible GE models, the pressure sensor is located near the bottom of the dishwasher tub, accessible after removing the lower front kick panel (secured by one or two screws). The sensor assembly connects to a small hose and a wiring harness connector. Tip: before replacing the sensor, remove it and inspect the pressure port and hose for grease, food residue, or mineral buildup — a clogged sensor port can cause H2O and FTD errors without the sensor itself being electrically failed. Clean the port and hose with warm water and a small brush, reinstall, and test the dishwasher. If the error codes persist after cleaning, replace the WD21X25468 sensor. To replace: disconnect the hose and wiring harness from the old sensor, unclip or unscrew the sensor from its mounting bracket, and install the new sensor in the same position. Reconnect the hose and harness, restore power and water, and run a test cycle. Tools needed: Phillips screwdriver. Frequently Asked Questions What does the dishwasher pressure sensor do? The pressure sensor monitors the water pressure — and therefore the water level — inside the dishwasher tub throughout the wash cycle. It sends continuous readings to the electronic control board, which uses the data to determine how much water to add during fill, when to stop filling, and whether the tub has drained completely before advancing to the next cycle phase. An accurate pressure sensor is essential for the dishwasher to fill to the correct level (not too much, not too little), wash with the correct spray arm pressure, and drain fully before moving on to rinse or dry cycles. What do error codes H2O and FTD mean on GE dishwashers? H2O error code on compatible GE dishwashers indicates that the dishwasher is not detecting enough water in the tub — either water is not filling at all, or the pressure sensor is not sensing the water that has filled. FTD (Failure to Drain) code indicates the dishwasher has not confirmed that the tub has drained within the expected time. Both codes can be caused by a faulty pressure sensor, a clogged sensor port, a failed fill valve, a blocked drain system, or control board issues. The pressure sensor should be inspected and tested first since it is the most accessible and commonly replaced component for these two error codes. Should I try cleaning the sensor before replacing it? Yes — absolutely. The pressure sensor on GE dishwashers can produce H2O and FTD error codes when its pressure port or connected hose becomes clogged with grease, food residue, or hard water mineral deposits — even if the sensor itself is electrically intact. Before ordering a replacement, remove the sensor, inspect the pressure port opening, and clean it thoroughly with warm water and a small brush. Flush the connected hose to clear any buildup. Reinstall and run a test cycle. If the error codes return, the sensor has electrically failed and needs replacement with the WD21X25468. My dishwasher won't fill unless I pour water in manually first — is this the pressure sensor? Yes — this is a classic symptom of a clogged or failed pressure sensor. When the sensor port is blocked, the sensor reads zero pressure (empty tub) even when the dishwasher starts. In some cases the control board interprets this as a drainage confirmation and will not initiate the fill cycle. Pouring water into the filter manually raises the physical water level enough to trigger filling. Check and clean the sensor port as described above. If cleaning does not resolve the issue, replace the WD21X25468 sensor. Is this a Genuine OEM or aftermarket part? This is a Genuine OEM part manufactured by GE to factory specifications. It is the exact same pressure sensor assembly installed in compatible GE, GE Profile, GE Café, Hotpoint, and related brand dishwashers from the factory — guaranteed fit, materials, and performance. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

WD19X25278 Dishwasher Diverter Assembly The XPARTCO WD19X25278 is an aftermarket replacement diverter assembly for GE dishwashers, and also fits select Hotpoint, Haier, Monogram, and Café models. This assembly controls the flow of water to the spray arms, directing wash water to the upper or lower spray arm at the correct point in the cycle for thorough, even cleaning. The assembly includes a valve and float mechanism designed to optimize water flow while minimizing noise. Common causes of failure include a worn or cracked diverter valve, or a rubber boot/hose connection that develops a leak over time. Symptoms of a failing diverter assembly include water pooling underneath the dishwasher, poor washing performance from one or both spray arms, or unusual noise during the wash cycle. It directly replaces AP6871922, WD18X21678, 4922277, PS12710077, WD00X25260, WD19X25259, and WD19X25278-25PK. Quick Answer The XPARTCO WD19X25278 Dishwasher Diverter Assembly fixes GE, Hotpoint, Haier, Monogram, and Café dishwashers with water pooling underneath the unit, poor washing performance from the spray arms, or unusual noise during the cycle. Replaces AP6871922, WD18X21678, 4922277, PS12710077, WD00X25260, WD19X25259, WD19X25278-25PK. Make sure the diverter is fully engaged with the spout on the wash pump before tightening the hose clamp — one customer had the tube cut when tightening the clamp without full engagement first. Common Problems This Part Fixes Water pooling or leaking underneath the dishwasher Poor washing performance from one or both spray arms Unusual noise during the wash cycle Water not properly directed to the correct spray arm Inconsistent cleaning results between the upper and lower racks Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dishwasher diverter assembly directly replaces the following OEM and cross-reference part numbers: WD19X25278, 4466639, 4922277, WD00X25260, WD18X21678, WD19X25259, WD19X25278-25PK, AP6024268, AP6871922, AGE24645, PD00049646, EAP11736568, EAP12710077, PS11736568, PS12710077 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This diverter assembly is compatible with select GE dishwashers, and also fits select Hotpoint, Haier, Monogram, and Café dishwashers built on the GE platform, including model numbers such as ADT521PGJ0BS, ADT521PGJ0WS, ADT521PGJ2BS, GDT655SGJ5BB, GDF510PGJ0BB, GDF511PGM0WW, GDF520PGJ0BB, and GDF530PGM0BB. Note: The assembly may include multiple parts depending on your model — refer to your appliance's parts diagram for a complete list. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Aftermarket replacement diverter assembly — controls water flow to the spray arms Resolves "water pooling underneath," "poor spray arm performance," and "unusual noise" symptoms Valve and float assembly engineered to optimize water flow while minimizing noise Direct drop-in replacement matching the original mounting and connections Replaces AP6871922, WD18X21678, 4922277, PS12710077, WD00X25260, WD19X25259, and WD19X25278-25PK Compatible with GE, Hotpoint, Haier, Monogram, and Café dishwashers Aftermarket replacement built to OEM-equivalent quality standards DIY-friendly repair Product Specifications Part Number WD19X25278 OEM Part Number WD19X25278 Part Type Dishwasher Diverter Valve Assembly Condition Aftermarket Replacement Function Controls water flow direction to the upper and lower spray arms Design Valve and float assembly Repair Difficulty Easy to Moderate — DIY-friendly Quantity 1 diverter assembly Compatible Brands GE, Hotpoint, Haier, Monogram, Café Installation Notes ⚠️ Unplug Dishwasher And Shut Off Water Supply Before Starting — Fully Engage The Spout Before Tightening The Clamp Disconnect power at the outlet or shut off the circuit breaker, and shut off the water supply before beginning. Wear work gloves. Open the dishwasher door and remove the racks to expose the bottom of the dishwasher. Locate the diverter assembly at the bottom of the unit and remove the two screws securing it in place. Disconnect the old assembly from the wash pump spout and any hose connections. Before tightening the hose clamp on the new assembly, make sure the diverter is fully and securely engaged with the spout on the wash pump. One customer had their diverter's tube cut when the clamp was tightened without the assembly being fully seated first — take your time to confirm a proper seat before applying clamp pressure. Secure the new WD19X25278 assembly in place with the two mounting screws. Reconnect any hose connections and reinstall the dish racks. Restore the water supply and power, then run a test cycle — ideally checking underneath the unit partway through — to confirm no leaking from the diverter area and correct water distribution to both spray arms. Tools needed: Phillips screwdriver, pliers, work gloves. Frequently Asked Questions I'm seeing water pooling under my dishwasher. Is this the part I need? Yes, this is a commonly documented symptom. If the diverter's rubber boot or hose connection has developed a leak, water can spray or drip during the wash cycle and collect underneath the unit. One customer traced their leak to a factory-defective hose in the diverter assembly, and unfortunately the leaking water had also gotten into their circulation pump motor over several loads, eroding the motor brushes — so it's worth inspecting the pump motor as well if you've had a diverter leak for a while before noticing it. Any tips to avoid damaging the new part during installation? Yes — make sure the new diverter is fully engaged with the spout on the wash pump before tightening the hose clamp. One customer's first replacement part was ruined because the clamp was tightened before the assembly was properly seated, which cut into the tube. Taking an extra moment to confirm a full, secure connection before clamping down prevents this. Is this a difficult repair? No, this is generally a DIY-friendly repair. It involves removing the dish racks, unscrewing two mounting screws to access the diverter at the bottom of the dishwasher, and swapping the assembly, typically without needing to pull the dishwasher out from under the counter. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine GE OEM part, but is manufactured to match the valve and float design, mounting configuration, and connections of the original WD19X25278 diverter assembly used in compatible GE, Hotpoint, Haier, Monogram, and Café dishwashers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

EXPW79SC (8 Pack) Washing Machine Fill Hose Gasket with Screen 8 Pack compatible with 5/ 8 inch washing machine and 3/4 inch garden hose Fine Screen the rubber washer with stainless steel filter mesh, serves as a flow restrictor can reduce the waste of water effectively     

Read more less

W10518394 Genuine OEM Whirlpool Dishwasher Heating Element The W10518394 is a Genuine OEM Whirlpool replacement dishwasher heating element compatible with select Whirlpool, Maytag, KitchenAid, Amana, and Kenmore Whirlpool-built dishwashers — including the WDF, WDT, ADB, and related series. The heating element is mounted at the bottom of the dishwasher tub and serves two purposes: it heats the wash water to the temperature required by the selected cycle (improving cleaning performance and helping detergent dissolve and work effectively), and it provides drying heat at the end of the cycle to evaporate moisture from dishes during the heated dry phase. When the element fails, dishes come out wet, glassware is spotted or cloudy, and wash performance noticeably degrades. This is an oval-shape element rated 1200W, approximately 15"L x 3"W x 3"H. As a Genuine OEM part manufactured by Whirlpool to factory specifications, the W10518394 directly replaces W10518394VP, W10134009, W10441445, 8194250, 8563007, 8563464, 8572861, 2977737, 1381534, 8268559, A3-06, AP4325066, AP5690151, EAP9605070, PD00012075, PS1960583, and PS9605070. The element mounts to the bottom of the tub with large nuts on the underside — the rubber washer (Whirlpool 717273) and heater nut (Whirlpool 8268548) are sold separately if they need replacement. Important: after installation on most Whirlpool dishwashers, you must run the diagnostic mode to reset the control board to recognize the new element. Installs in 30–45 minutes with basic hand tools. Quick Answer The W10518394 Genuine OEM Whirlpool Dishwasher Heating Element fixes Whirlpool, Maytag, KitchenAid, Amana, and Kenmore dishwashers where dishes come out wet, glassware is spotted, wash water isn't getting hot, or the heated dry phase isn't working. Oval shape, 1200W, ~15"L x 3"W x 3"H. Genuine OEM. Replaces W10518394VP, W10134009, W10441445, 8194250, 8563007, 8563464, 8572861, 2977737, AP4325066, AP5690151, PS1960583, PS9605070. Diagnostic reset required on most Whirlpool dishwashers after installation. Rubber washer (717273) and heater nut (8268548) sold separately if needed. Common Problems This Part Fixes Dishes coming out wet at the end of the cycle — element not providing heat for the drying phase Wash water not getting hot enough — poor cleaning performance even with proper detergent Glassware coming out cloudy or spotted — water not reaching temperature for proper detergent activation Heated dry cycle not working — no warm air at the end of the cycle Element visibly burned through, broken, or showing arcing damage Multimeter continuity test on the element shows an open circuit (no continuity) Heating element showing the wrong region glowing red (only a 6" segment heating rather than the whole element) Detergent not fully dissolving — water too cool to activate the formulation Replaces Part Numbers This dishwasher heating element directly replaces the following OEM and cross-reference part numbers: W10518394, 2977737, 8194250, 8563007, 8572861, W10134009, W10441445, W10518394VP, AWP40983, PD00004893, EAP8260087, AP5690151, PS8260087. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Always confirm the shape and dimensions of your old element match this oval ~15" element before ordering — some Whirlpool dishwashers use a different horseshoe-style element instead. Compatibility This dishwasher heating element is compatible with select Whirlpool, Maytag, KitchenAid, Amana, and Kenmore dishwashers, including: Whirlpool dishwashers — WDF330PAHS, WDF520PADM, WDT720PADM, WDT730PAHZ series and related models Whirlpool dishwashers — additional WDF and WDT series models (verify with parts diagram) Maytag dishwashers — select models (verify with parts diagram) KitchenAid dishwashers — select models Amana dishwashers — ADB1400AGW and related models Kenmore / Sears dishwashers — select Whirlpool-built models Important — Confirm Element Shape Before Ordering: The W10518394 is an oval-shape heating element approximately 15" in length. Some Whirlpool-platform dishwashers use a different horseshoe-style heating element instead, which is NOT interchangeable with this one. Before ordering, visually compare your old element's shape and length to this part, or check your dishwasher's parts diagram to confirm W10518394 is the correct element for your specific model. If your element is horseshoe-shaped, you need a different part number — contact our support team with your model number. Key Features Genuine OEM part manufactured by Whirlpool to factory specifications — guaranteed fit and performance Heats wash water for optimal cleaning performance and provides drying heat during the heated dry phase Rated 1200W for efficient heating and reliable temperature control Oval-shape element approximately 15" L x 3" W x 3" H Mounts in the bottom of the dishwasher tub, secured underneath with large nuts Note: rubber washer (Whirlpool 717273) and heater nut (Whirlpool 8268548) sold separately if yours need replacement Diagnostic reset required on most Whirlpool dishwashers after installation (typically pressing any 3 buttons in sequence 3 times) Replaces 18+ OEM and cross-reference part numbers including W10518394VP, W10134009, W10441445, 8194250, 8563007, 8563464, 8572861, AP4325066, AP5690151, PS1960583, PS9605070 Compatible with Whirlpool WDF and WDT series, Maytag, KitchenAid, Amana ADB1400AGW, and Kenmore Whirlpool-built dishwashers DIY repair — installs in 30–45 minutes with basic hand tools Product Specifications Part Number W10518394 Part Type Dishwasher Heating Element Condition Genuine OEM Application Dishwashers (Whirlpool platform) Shape Oval (NOT interchangeable with horseshoe-style elements) Wattage 1200W Dimensions Approximately 15" L x 3" W x 3" H Mounting Location Bottom of dishwasher tub Related Parts (Sold Separately) Rubber Washer (717273), Heater Nut (8268548) Post-Install Step Diagnostic reset required on most Whirlpool dishwashers Compatible Brands Whirlpool, Maytag, KitchenAid, Amana, Kenmore Installation Notes ⚠️ Unplug Dishwasher and Shut Off Water Before Starting — Don't Touch Element with Bare Hands Disconnect power at the breaker and shut off the water supply at the valve under the sink before beginning. Wear work gloves and safety glasses to protect your hands and eyes. Handle the new heating element only by the metal end terminals or its support brackets — do NOT touch the heating coil itself with bare fingers; skin oils can cause hot spots that shorten element life. From inside the dishwasher tub, the element is visible at the bottom — it's the looped metal coil running along the floor of the tub. Remove the bottom rack and any debris to clear access. To access the wire connections and mounting nuts, you'll need to either reach underneath the dishwasher from the front access panel or, on some installations, pull the dishwasher out partially. From underneath: disconnect the two wires from the bottom of the element terminals (photograph the wire connections first to ensure correct reinstallation). Remove the plastic nuts holding the element terminals in place. From inside the tub, lift the old element straight up and out. Inspect the rubber washers — if they're cracked, hardened, or torn, replace them now with new 717273 washers. Install the new W10518394 element through the same mounting holes, replace the rubber washers if needed, and secure with the plastic nuts (or new 8268548 nuts) from underneath. Reconnect the two wires to the terminals matching your original orientation. Important: after restoring power, run the Whirlpool diagnostic mode to reset the control board — on most models this is done by pressing any three buttons in sequence three times and closing the door, which initiates a ~30-minute diagnostic cycle. The new element will not be recognized by the control until this is done. Tools needed: Phillips screwdriver, 5/8" wrench, 5/16" nut driver, 3/4" wrench, work gloves, safety glasses. Frequently Asked Questions Why are my dishes coming out wet — is the heating element the cause? Most likely, yes — wet dishes are the classic signature of a failed dishwasher heating element. The element provides heat for the dry phase, evaporating moisture from dish surfaces. When it fails, dishes simply air-dry, which leaves them wet (especially plastics and the interior of inverted glassware). To confirm: with the dishwasher unplugged, disconnect the wires from the element and check continuity with a multimeter. A working element shows continuity; a failed element shows an open circuit (infinite resistance). Also check that you have the heated dry option enabled in your cycle settings — some users mistakenly turn off heated dry and then assume the element has failed. After installing the new element, the dishwasher still isn't heating — why? On most Whirlpool dishwashers, you must run the diagnostic mode after replacing the heating element so the control board recognizes the new part. To enter diagnostic mode on most Whirlpool models, press any three buttons in sequence three times rapidly, then close the door — this starts a roughly 30-minute diagnostic cycle that resets the heater logic. If you've installed the new element correctly and it still isn't heating after the diagnostic cycle, also check the high-limit thermostat (a safety component that can stop power to the element if it has failed open). Confirm your wire connections are tight on the element terminals as well. How is the W10518394 different from horseshoe-shape heating elements? The W10518394 is an oval-shape element about 15" in length. Some Whirlpool-platform dishwashers — even similar-looking models — use a horseshoe-shape element instead, which has a different mounting hole pattern and shape that won't fit positions designed for the oval element. The two are NOT interchangeable. Before ordering, compare your old element to a photo of the W10518394, or check your dishwasher's parts diagram. If your old element is horseshoe-shaped, contact our support team with your model number and we'll help identify the correct horseshoe-style element for your dishwasher. Do I need to replace the rubber washers and nuts when installing this? Not always — they're reusable as long as they're in good condition. Inspect the rubber washers (Whirlpool 717273) for cracks, hardening, or tears. If they're brittle or torn, replace them now while you have the element out — they prevent water leaks from the tub at the element mounting points. The plastic heater nuts (Whirlpool 8268548) are usually reusable unless visibly damaged. Both parts are sold separately if you need replacements. Reusing torn rubber washers is the most common cause of leaks after this repair, so don't skip the inspection. Is this a Genuine OEM or aftermarket part? This is a Genuine OEM part manufactured by Whirlpool to factory specifications. It is the exact same heating element installed in compatible Whirlpool, Maytag, KitchenAid, Amana, and Kenmore Whirlpool-built dishwashers from the factory — guaranteed fit, materials, and performance. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

W10757833 Dishwasher Control Panel Fits specific KitchenAid dishwasher models. Replaces Part Numbers: W10757833, 8531268, 3452787, 8531265, 8531537, 8564487, 8564565, AP5956414, PS10064580. Description: This Rack Adjuster is a Genuine OEM part for Whirlpool dishwashers, designed to allow for the easy adjustment of the dishwasher rack's height. This feature accommodates dishes of various sizes. By providing the flexibility to adjust the rack height, this part enhances the dishwasher's adaptability to different washing needs.

Read more less

XPARTCO DA82-01415A Refrigerator Water Leak Service Kit Water leak repair kit with updated internal duck bill. Fits select Samsung refrigerator models. Replaces Part Numbers: DA82-01415A, 3436781, AP5957964, PS10058968. Description: This Water Leak Repair Kit is a replacement part for select Samsung refrigerator models, this field service kit used to address water leakage and excessive frost in bottom freezer or French door refrigerators with dual evaporators. The kit includes a drain probe, two drain tubes, and two silver foam strips. With these parts, you can prevent excessive frost buildup on the evaporator cover and fix issues like water leaks under the crisper or odd fan noises that stop when the doors are opened.   This is an aftermarket part that can be used as a replacement for the OEM part

Read more less

XPARTCO WH01X27954 Washer Lid Switch (Old Style) Product Overview The XPARTCO WH01X27954 Washer Lid Switch (Old Style) is designed to restore proper lid detection and washer operation. This high-quality replacement detects whether the washer lid is closed, allowing safe operation during wash and spin cycles. A broken or faulty switch can cause the washer not to start, stop mid-cycle, or fail to spin. Replacing it with this durable XPARTCO switch restores normal functionality and safety performance. Old-style GE lid switch (does not require harness replacement). Quick Answer If your washer will not spin, drain, or start properly, a faulty WH01X27954 lid switch may be the cause. Replacing this old style washer lid switch helps restore normal washer operation and cycle performance. Replaces Part Numbers Replaces OEM part number: WH08X32697, WH01X27954, WH08X31577, WH01X24114, WH01X26114, 290D1580P001, 290D1580P004, 290D1580P002, 290D1580P003, WH08X31577, AP7015047, PS16554755. Compatibility This washer lid switch is compatible with select GE, Hotpoint, and other compatible top-load washers that use the old style lid switch design. Example compatible models include (but are not limited to): GE GTW220ACK1WW GTW220ACK2WW GTW220ACK3WW GTW220ACK4WW GTW220ACK5WW GTW220ACK6WW GTW220ACK7WW GTW220ACKWW GTW330ASK0WW GTW330ASK1WW GTW330ASK2WW GTW330ASK3WW GTW330ASK4WW GTW330ASKWW GTW335ASN0WW GTW335ASN2WW GTW335ASNWW GTW460AMJ0WW GTW460AMJ1WW GTW460AMJ2WW GTW460AMJ3WW GTW460AMJ4WW GTW220ACK4WW GTW220ACK5WW GTW220ACK6WW GTW220ACK7WW GTW220ACKWW GTW330ASK0WW GTW330ASK1WW GTW335ASN0WW. GE Top-Load Washers Hotpoint Washers Old Style Lid Switch Applications Always verify your washer’s model number before ordering. Contact our support team if you’re unsure. Common Problems This Part Fixes Washer not spinning Washer not draining Washer not starting cycle Lid switch not detecting closed lid Key Features Designed for old style washer lid switch applications Helps restore safe and proper washer operation High-quality aftermarket replacement Durable construction for reliable performance Product Specifications Part Number: WH01X27954 Part Type: Washer Lid Switch Brand: XPARTCO Condition: New OEM / Aftermarket: Aftermarket Application: Top-Load Washers Style: Old Style Troubleshooting Guide Washer fills but does not spin → Lid switch may be faulty Washer will not start cycle → Lid switch may not detect closed lid Washer stops before spin cycle → Defective lid switch can interrupt operation When Should You Replace This Lid Switch? Replace this lid switch if your washer does not start, spin, or drain properly, or if the switch no longer detects when the lid is closed. Installation Notes ⚠️ Disconnect power before installation. Access the lid switch area according to your washer design and install the replacement securely. Refer to your appliance manual if needed. Related Parts Washer Lid Strike Washer Timer Washer Door or Lid Lock Components Frequently Asked Questions Will this lid switch fit my washer?This switch fits select GE and compatible washers that use the old style lid switch. Always verify your model number. What does a washer lid switch do?It detects whether the washer lid is closed so the machine can operate safely. What are signs of a bad lid switch?Common signs include the washer not spinning, not starting, or stopping before the cycle completes. Is this the old style version?Yes, this listing is for the old style WH01X27954 washer lid switch. Shop With Confidence Parts-O-Matic is a U.S.-based appliance parts retailer specializing in OEM and high-quality aftermarket parts. We offer fast shipping, reliable products, and expert support. Fast Shipping Quality Tested Parts Compatibility Support  

Read more less

XPARTCO W10804664 Washer Motor Run Capacitor (50µF) The XPARTCO W10804664 is an aftermarket replacement motor run capacitor for Whirlpool-built top-load washers. This capacitor works alongside the washer's motor to help it start and run efficiently — it briefly boosts the voltage delivered to the motor at the moment it's commanded to start, giving it the extra push needed to overcome its own inertia and begin turning smoothly. Once the motor is running, the capacitor continues supporting steady, efficient operation for the duration of the cycle. Rated 50 MFD (µF) at 250VAC. Over time, the dielectric material inside a run capacitor breaks down from repeated startup stress and heat cycling, which reduces its effectiveness or causes it to fail outright. A failing capacitor produces a clear symptom: the washer motor hums but won't start, or the motor makes noise during use without turning properly. Left unaddressed, a struggling motor can also run hotter than normal and wear out faster than it should. It directly replaces W10278117, 4247711, W10666221, W10804664VP, AP5982844, EAP11703494, and PS11703494. Quick Answer The XPARTCO W10804664 Washer Motor Run Capacitor fixes Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Crosley top-load washers where the motor hums but won't start, or makes noise during use without running properly. Rated 50 MFD (µF), 250VAC. Replaces W10278117, 4247711, W10666221, W10804664VP, AP5982844, EAP11703494, PS11703494. Capacitors store a dangerous electrical charge even after power is disconnected — always discharge before handling. Common Problems This Part Fixes Washer motor hums but won't start Motor makes noise during operation without turning properly Washer won't agitate or spin because the motor never gets up to speed Motor that struggles to start under load but may run fine once already spinning Washer motor running hotter than normal Cycle stalling at the start of agitation or spin Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer motor run capacitor directly replaces the following OEM and cross-reference part numbers: W10804664, W10804664VP, W10278117, 4247711, W10666221, AP5982844, EAP11703494, AWP41264, PD00024697, PS11703494 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This motor run capacitor is compatible with select Whirlpool-built top-load washers across the Whirlpool family of brands, including: Whirlpool top-load washers — including 7MWTW1750YW0, 7MWTW1750YW1, 7MWTW1950YW0, 7MWTW1950YW1 Maytag, KitchenAid, Jenn-Air, and Amana top-load washers (select models) Magic Chef, Admiral, and Norge top-load washers (select models) Roper and Crosley top-load washers (select models) Note: Whirlpool uses several different washer motor run capacitors across its platforms with similar-looking part numbers but different MFD ratings — for example, other listings cover 45 MFD (W11158830/W10625045) and different 50 MFD variants (W11395618/W10625046) used on other washer model families, none of which are interchangeable with this 50 MFD/250VAC W10804664. Always verify your full model number and match the MFD rating printed on your original capacitor before ordering. Contact our support team with your model number if you're unsure. Key Features Aftermarket replacement motor run capacitor — boosts voltage to help the washer motor start and run efficiently Rated 50 MFD (µF) at 250VAC Resolves "motor hums but won't start," "noisy motor," and "won't agitate or spin" symptoms caused by capacitor failure Direct drop-in replacement — mounts to the original bracket and wiring Replaces W10278117, 4247711, W10666221, W10804664VP, AP5982844, EAP11703494, and PS11703494 Compatible with Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Crosley top-load washers Aftermarket replacement built to OEM-equivalent quality standards Straightforward repair — basic hand tools and some disassembly required Product Specifications Part Number W10804664 OEM Part Number W10804664 Part Type Washer Motor Run Capacitor Condition Aftermarket Replacement Application Top-Load Washers (Whirlpool-Built) Capacitance 50 MFD (µF) Voltage 250VAC Function Boosts voltage to the motor to support efficient starting and running Repair Difficulty Easy to Moderate — basic hand tools required Quantity 1 run capacitor Compatible Brands Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, Crosley Installation Notes ⚠️ Danger — Capacitors Store A Dangerous Electrical Charge Unplug the washer or shut off the house circuit breaker before beginning. A capacitor stores an electrical charge even after power has been disconnected, and that charge can deliver a serious or fatal shock. Before touching either terminal, discharge the capacitor by shorting its two terminals together using an insulated-handle screwdriver, or by using a proper capacitor discharge tool with a resistor. Never short the terminals with a bare metal tool held with your bare hand. If you are not fully comfortable performing a capacitor discharge safely, have a qualified appliance technician replace this part instead. ⚠️ Shut Off Hot And Cold Water Supplies Before Starting Wear work gloves. In addition to disconnecting power, turn off the hot and cold water supplies before beginning disassembly. Access to the capacitor typically requires removing the washer's console and outer body panels — remove the mounting screws and release any spring clips securing the body to the frame, using a putty knife to gently pop them free. Locate the capacitor, usually mounted to the rear panel or motor bracket area. Photograph the wiring before disconnecting anything. After confirming the capacitor is fully discharged, disconnect the wire terminals from the old capacitor, remove its mounting clip or bracket, and pull it free. Install the new W10804664 capacitor in the same position, reconnect the wire terminals, and secure it in its mounting clip or bracket. Reassemble the body panels, spring clips, and console in reverse order. Restore water and power, then run a test cycle through both agitate and spin, confirming the motor starts promptly without humming or hesitation. Tools needed: putty knife, Phillips screwdriver, insulated-handle screwdriver or capacitor discharge tool, work gloves. Frequently Asked Questions My washer motor hums but won't start. Is this the right part? Yes, this is the classic symptom of a failing run capacitor. Since this capacitor's job is to boost voltage to the motor at startup, a weak or failed capacitor can leave the motor energized and humming without ever getting the push it needs to actually begin turning. How do I know I have the right MFD rating for my washer? Check the rating printed directly on your original capacitor's body — this listing is specifically 50 MFD at 250VAC. Whirlpool uses several different run capacitors across its washer platforms, including a 45 MFD version and other 50 MFD variants with different part numbers, and installing the wrong rating can leave the motor under- or over-supported. If you're not sure, contact our support team with your model number. Do I need to shut off the water supply just to replace a capacitor? It's a precaution taken because accessing this capacitor typically requires removing the washer's outer body and console, which involves working around the same general area as the water inlet connections. Shutting off the water first prevents any accidental spills or pressure issues while the body is open, even though you won't necessarily be disconnecting the water lines themselves for this specific repair. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured to match the 50 MFD, 250VAC electrical rating and mounting configuration of the original W10804664 run capacitor used in compatible Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, and related top-load washers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

Genuine GE OEM Part GE WD24X25325 Dishwasher Genuine Fan Vent Assembly Genuine GE door-vent blower/fan assembly for select GE and Haier dishwashers. Product Overview The GE WD24X25325 Dishwasher Fan Vent Assembly is a genuine OEM replacement used in the dishwasher door ventilation system. The blower circulates air through the door vent during the drying portion of the cycle to help reduce retained moisture and improve drying performance. Quick Answer WD24X25325 is a Genuine GE OEM dishwasher door-vent blower/fan motor assembly. It is used on select GE and Haier dishwashers and helps move moist air through the door vent during drying. Common Problems This Part May Fix Poor drying performance Excess moisture remaining after a cycle Door vent fan does not run Unusual noise from the vent/blower area Moist air is not being exhausted through the door vent Replaces and Cross-References WD24X25325, 265D2664G005, U40G12BS3A5-51, AGE25072, AP6972063, EAP12726435, PD00073154, PS12726435. Cross-reference numbers are supplied for identification. Always verify the complete dishwasher model number before ordering. Compatibility Fits select GE and Haier dishwashers. Compatible model examples include: CDT800P2N0S1 CDT805P2N0S1 CDT845P2N3S1 DDT700SBN0TS GDF645SSN0SS GDT645SFN3DS GDT665SFN0DS GDP665SYN3FS PDT715SYN2FS PDT715SFN0DS PDP715SYN3FS QDP555SYN0FS Important: This is only a partial compatibility list. Confirm the exact dishwasher model number before purchase because similar models may use a different vent or blower assembly. Key Features Genuine GE Appliances OEM part Complete door-vent blower/fan assembly Circulates air through the dishwasher door vent Helps reduce moisture during drying For select GE and Haier dishwashers Product Specifications Manufacturer GE Appliances Manufacturer Part Number WD24X25325 Part Type Dishwasher Fan Vent / Door Vent Blower Assembly Condition New Part Quality Genuine OEM Application Dishwasher Door Ventilation / Drying System Approx. Shipping Weight 0.5 lb Installation Notes Disconnect electrical power to the dishwasher at the breaker before service. Access the door vent assembly according to the appliance service procedure. Disconnect the wiring connector carefully before removing the old fan assembly. Transfer or reuse any hardware only as directed for the specific model. Confirm the vent path is clear and the new assembly is fully seated before reassembly. Diagnostic note: Poor drying can also result from rinse-aid settings, heating-system faults, blocked vent passages, or control issues. Confirm the fan assembly is defective before replacing it. Frequently Asked Questions Is WD24X25325 a Genuine GE OEM part? Yes. GE Appliances identifies WD24X25325 as a genuine replacement fan vent assembly. What does this fan assembly do? It circulates air through the dishwasher door vent to help reduce moisture during the drying stage. Does it fit every GE dishwasher? No. It fits specific GE and Haier models. Verify the complete model number before ordering. Is this only the fan motor? This listing is for the complete WD24X25325 fan vent / door-vent blower assembly as supplied by GE. Shop With Confidence Use your dishwasher's complete model number to confirm fitment before purchase. Genuine GE OEMFan Vent AssemblyModel Verification RecommendedFast U.S. Shipping

Read more less

W11126005CM Dishwasher Wash Vane Sensor Description: This Sensor is a replacement component specifically designed for certain Whirlpool dishwasher models. It plays a crucial role in monitoring cycle conditions like temperature and soil levels to automatically customize wash sequences. Causes of a bad sensor can include leaking or faulty wiring disrupting signals over time, mineral buildup gumming internal mechanisms, or damage from impact. Replaces Part Numbers: W11126005, W11503875, W10380177, W10380483, W10647239, AP6261394, PS12114437. This is an aftermarket part that can be used as a replacement for the OEM part. California Residents only WARNING: California’s Proposition 65 

Read more less

WD24X10018 Dishwasher Genuine Piston & Nut Assembly Replaces Part Numbers: WD24X10018, 821081, WD22X0133, WD22X133, WD24X0199, WD24X0220, WD24X199, WD24X220, AH260690, EA260690, AP2617344, PS260690. Description: This Piston & Nut Assembly is a Genuine parts for specific GE dishwasher models. It plays a critical role in the dishwasher’s water management system, helping to control water flow and ensuring proper drainage during the wash cycle. You should replace this piston & nut assembly if it becomes worn out or damaged. Common causes of a bad piston & nut assembly can include mineral buildup from hard water, general wear and tear from regular use, or physical damage due to debris or foreign objects in the dishwasher.

Read more less

WD19X25278 Dishwasher Genuine OEM Diverter Assembly Replaces Part Numbers: WD19X25278, WD18X21678, 4922277, WD00X25260, AP6871922, PS12710077. Description: This Diverter Valve Assembly Kit serves a Genuine OEM replacement Part for specific GE dishwasher models. Its key function is to provide an alternative passage for water to reach the upper spray arms of the dishwasher. A faulty or damaged diverter valve often manifests as water leaks within the dishwasher. When such leaks occur and can be traced back to the diverter valve, this assembly kit offers a comprehensive solution. It includes all necessary components and fasteners to efficiently replace the valve. This kit is suitable for use with specific General Electric dishwasher models.

Read more less