Search results for "Dryer belts and idler pulley"

XPARTCO D111-25GR Refrigerator Universal Directional Spun Copper Drier The XPARTCO D111-25GR is a universal spun copper filter drier for domestic and commercial refrigerators, freezers, and air conditioners. Installed in the sealed refrigerant line, this drier filters the refrigerant as it circulates through the system, removing moisture and contaminants that would otherwise damage internal components or restrict refrigerant flow over time. This directional drier is suitable for both refrigeration and air conditioning systems, compatible with R12, R22, R502, and R134A refrigerants. It features a 1" diameter body, approximately 8-1/8" in length, with a 1/4" O.D. copper tubing inlet paired with a 1/4" Schrader valve, and a 1/4" O.D. outlet. Equipped with a molecular sieve filter element and a 25g silica gel particle fill, this drier's higher desiccant content is more suitable for large refrigerators, freezers, and commercial refrigeration equipment. Filter driers are typically replaced whenever the sealed system is opened for service — such as after a compressor replacement or a refrigerant leak repair — since a used drier that has already absorbed moisture won't provide adequate protection for a newly serviced system. This is a universal cross-brand part, fitting any refrigeration system conforming to this filter drier's type and size specifications, and directly replaces ERD111, SUD111, PD111, TJ90SUD111, and WR86X25269. Quick Answer The XPARTCO D111-25GR Refrigerator Universal Directional Spun Copper Drier is installed in the sealed refrigerant line during service work such as a compressor replacement or refrigerant leak repair, filtering moisture and contaminants from the refrigerant. Compatible with R12, R22, R502, and R134A. 1" diameter, ~8-1/8" length, 1/4" O.D. copper tubing inlet with 1/4" Schrader valve, 1/4" O.D. outlet, molecular sieve filter element with 25g silica gel fill. Replaces ERD111, SUD111, PD111, TJ90SUD111, WR86X25269. This part must be installed by a qualified refrigeration or appliance technician — installation requires refrigerant recovery and brazing, and in the US, handling refrigerant legally requires EPA Section 608 certification. When This Part Is Used Replacing a filter drier as part of a compressor replacement Servicing the sealed system after a refrigerant leak repair General sealed-system service where the old drier has become saturated with moisture Restricted refrigerant flow traced to a clogged or failing drier Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This filter drier directly replaces the following OEM and cross-reference part numbers: ERD111, SUD111, PD111, TJ90SUD111, WR86X25269 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This is a universal XPARTCO filter drier compatible with a wide range of domestic and commercial refrigerators, freezers, and air conditioners across multiple brands, including GE (via WR86X25269). Note: Consult your appliance's service documentation or a qualified technician to confirm this drier's size and connection type are correct for your specific sealed system before purchasing. Contact our support team if you're unsure. Key Features Universal spun copper filter drier for refrigerators, freezers, and air conditioners Filters moisture and contaminants from refrigerant circulating through the sealed system Molecular sieve filter element Directional design 1" diameter, approximately 8-1/8" length 1/4" O.D. copper tubing inlet with 1/4" Schrader valve, 1/4" O.D. outlet Compatible with R12, R22, R502, and R134A refrigerants 25g silica gel fill — higher desiccant content suited to large refrigerators, freezers, and commercial refrigeration equipment Replaces ERD111, SUD111, PD111, TJ90SUD111, and WR86X25269 Compatible with a wide range of refrigeration and air conditioning brands Product Specifications Part Number D111-25GR Part Type Universal Directional Spun Copper Filter Drier Diameter 1" Length Approx. 8-1/8" Inlet 1/4" O.D. Copper Tubing + 1/4" Schrader Valve Outlet 1/4" O.D. Filter Element Molecular Sieve Desiccant Fill 25g Silica Gel Refrigerant Compatibility R12, R22, R502, R134A Recommended Use Large refrigerators, freezers, commercial refrigeration equipment Installation Professional/certified technician required — refrigerant recovery and brazing involved Compatibility Universal — multiple refrigeration and A/C brands Installation Requirements ⚠️ Professional Installation Required Installing a filter drier requires opening the sealed refrigerant system: recovering the existing refrigerant, brazing the new drier into the liquid line, evacuating the system to remove air and moisture, and recharging it with the correct refrigerant type and amount. This work involves pressurized refrigerant, an open flame or torch for brazing, and — in the United States — legally requires EPA Section 608 certification to purchase, handle, or recover most refrigerants. This is not a DIY repair. Have this part installed by a qualified, licensed refrigeration or appliance technician. Frequently Asked Questions Why does a refrigerator need a filter drier? A filter drier removes moisture and contaminants from the refrigerant as it circulates through the sealed system. Moisture inside a refrigeration system can cause internal corrosion, ice formation at restriction points, and acid formation that damages the compressor over time, so keeping the refrigerant clean and dry is essential to the system's long-term reliability. When does this part typically get replaced? A filter drier is normally replaced any time a technician opens the sealed system for service, such as during a compressor replacement or after repairing a refrigerant leak. Reusing an old drier after the system has been opened is not recommended, since a saturated drier no longer effectively removes moisture from the newly serviced system. Can I install this myself? No, this is not a DIY-appropriate repair. Installing a filter drier requires recovering refrigerant, brazing the new drier into the line, evacuating the system, and recharging it with refrigerant — all of which require specialized tools and training. In the United States, purchasing, handling, and recovering most refrigerants legally requires EPA Section 608 certification. This part should be installed by a qualified, licensed refrigeration or appliance technician. Is this an OEM or aftermarket part? This is a universal XPARTCO replacement part, manufactured to match the size, connection type, and desiccant specification of the original D111-family filter drier used across a wide range of refrigeration and air conditioning systems. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO DD31-00005A Dishwasher Drain Pump Motor The XPARTCO DD31-00005A is an aftermarket replacement drain pump motor for Samsung dishwashers. This pump uses an internal impeller to force wastewater out of the tub and through the drain hose during the drain phase of the wash cycle — it's the component doing the physical work every time your dishwasher empties itself between cycle stages and at the end of the wash. Rated 120V, 0.8A. Over time, the impeller can wear down, debris can jam the motor, or the motor windings themselves can fail electrically. A failing drain pump produces a very recognizable pattern: standing water left in the tub after a cycle finishes, water leaking from underneath the dishwasher, unusually loud or grinding noise during the drain phase, or a pump that audibly tries to run for a moment and then shuts off right away without actually clearing the water. It directly replaces AP4342621 and PS4222308. Quick Answer The XPARTCO DD31-00005A Dishwasher Drain Pump Motor fixes Samsung dishwashers that won't drain, leave standing water in the tub, leak underneath the unit, or run unusually noisy during the drain phase. 120V, 0.8A. Replaces AP4342621, PS4222308. This is the drain pump — not the same part as the wash/circulation pump (DD31-00004B), which handles spraying water during the wash itself rather than draining it afterward. Common Problems This Part Fixes Dishwasher not draining — standing water left in the tub after a cycle Water leaking from underneath the dishwasher Unusually loud, grinding, or strange noise during the drain phase Pump that tries to run briefly, then shuts off right away without draining Dishwasher running noisily overall Cycle that stalls or won't advance past the drain step Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dishwasher drain pump motor directly replaces the following OEM and cross-reference part numbers: DD31-00005A, 1550731, DW0005A, AP4342621, ASM35435 PD00002014, PS4222308 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This drain pump motor is compatible with select Samsung dishwashers, including model numbers such as: DMR57LFB, DMR57LFS, DMR57LFW DMR77LHB, DMR77LHS, DMR77LHW DMR78AHB, DMR78AHS, DMR78AHW DMT300RFB, DMT300RFS, DMT300RFW DMT400RHB, DMT400RHS, DMT400RHW DMT800RHB, DMT800RHS, DMT800RHW Note — drain pump, not wash pump: This is the drain pump, which removes wastewater from the tub. It is a different part from the DD31-00004B wash/circulation pump motor, which sprays water through the spray arms during the wash itself. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure which pump your dishwasher needs. Key Features Aftermarket replacement drain pump motor — removes wastewater from the tub during the drain phase Resolves "not draining," "standing water," "leaking underneath," and "noisy drain phase" symptoms caused by pump failure Impeller-driven design for efficient water removal through the drain hose Rated 120V, 0.8A Direct drop-in replacement — matches the original mounting and hose connections Replaces AP4342621 and PS4222308 Compatible with a range of Samsung dishwasher models Aftermarket replacement built to OEM-equivalent quality standards Product Specifications Part Number DD31-00005A OEM Part Number DD31-00005A Part Type Dishwasher Drain Pump Motor Condition Aftermarket Replacement Brand Samsung Function Removes wastewater from the tub during the drain phase Voltage 120V Amperage 0.8 A Related Part DD31-00004B wash/circulation pump (different function, sold separately) Repair Difficulty Moderate — tight working space under the unit Quantity 1 drain pump motor Compatible Brand Samsung Installation Notes ⚠️ Unplug Dishwasher And Shut Off Water Supply Before Starting — Remove Standing Water First Unplug the dishwasher and shut off the water supply before beginning. Wear work gloves. If there's standing water left in the tub from the original failure, remove as much as possible by hand with a cup or towel before starting the repair. Access to the drain pump is typically from underneath the unit, which can mean a tight working space — pulling the dishwasher partially out from under the counter, or working from the front after removing the lower access panel, makes this considerably easier depending on your installation. Photograph the wiring and hose connections before disconnecting anything. Disconnect the electrical connector and the drain hose connections from the old pump, remove its mounting screws or clips, and pull it free. Install the new DD31-00005A pump in the same position, reconnect the drain hose connections securely, and reconnect the electrical connector fully. Restore the water supply and power, then run a cycle and check underneath for leaks while confirming the tub drains completely at the end. Tools needed: Phillips screwdriver, pliers, towels or a small cup for removing standing water, work gloves. Frequently Asked Questions My dishwasher pump tries to run for a second, then shuts off. Is that the drain pump? Yes, this is a documented symptom of a failing drain pump motor — one customer described exactly this pattern, where the pump attempted to run and then shut off right away without actually clearing the standing water. This typically points to a motor that's jammed, worn, or electrically failing rather than a clog, since a simple clog usually lets the motor keep running (just ineffectively) rather than shutting off immediately. Access to my drain pump is really tight. Is that normal? Yes, this is a common challenge with under-counter dishwasher installations — the drain pump often sits low and toward the back, and reaching it can mean working in a cramped space regardless of the model. Removing standing water first and having patience with the process makes a real difference, and pulling the unit partially forward, if your installation allows it, can improve access significantly. Is this the same as the wash pump on my dishwasher? No. This DD31-00005A is specifically the drain pump, which removes wastewater from the tub. Your dishwasher's separate wash/circulation pump (DD31-00004B) is what sprays water through the spray arms during the actual wash portion of the cycle. If your dishwasher isn't cleaning dishes well but drains fine, the wash pump — not this drain pump — is more likely the issue. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Samsung OEM part, but is manufactured to match the electrical rating, impeller design, and mounting configuration of the original DD31-00005A drain pump motor used in compatible Samsung dishwashers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

W10341320 (OE) Refrigerator Water Inlet Valve The W10341320 (OE) is an Original Equipment (OE) replacement dual secondary water inlet valve compatible with a wide range of Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore side-by-side refrigerators. This dual-solenoid valve controls water flow to two destinations — the refrigerator's water dispenser and the ice maker. Each solenoid opens independently when the control board calls for water at that destination, and closes the moment the call is dropped. When one or both solenoids fail, you lose water at the dispenser, ice production stops or slows, or the valve begins leaking at its connections. Rated 110/120V, 50/60Hz. Dual solenoid: W1 = 20W, W2 = 35W. Important: this is the SECONDARY valve, not the primary water inlet valve — many Whirlpool side-by-side refrigerators use both, and if your primary valve is working fine but you're still losing water or ice, the secondary valve is the likely culprit. It directly replaces WPW10341320, AP6019939, PS11753250, EAP11753250, 1937969, and K-78032. Common repair for leaks at the valve connections. Installs in about 30 minutes with basic hand tools and novice repair experience. Quick Answer The W10341320 (OE) Refrigerator Water Inlet Valve fixes Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, and Kenmore side-by-side refrigerators with no water through the door, an ice maker that won't make ice or makes too little ice, or leaking at the valve connections. Dual secondary valve — dual solenoid (W1=20W, W2=35W), 110/120V, 50/60Hz. Original Equipment (OE) — same design and performance as the factory part, without the OEM label. Replaces WPW10341320, AP6019939, PS11753250, EAP11753250, 1937969, K-78032. This is the SECONDARY valve — not the primary water inlet valve (W10238100). Common Problems This Part Fixes No water dispensing through the door — dispenser solenoid failed Ice maker not making ice — ice maker solenoid failed Ice maker dispensing too little ice — solenoid partially failed or restricted Water leaking from the valve or its connections Water dispenser works but ice maker doesn't (or vice versa) — one of the two solenoids has failed Weak or slow water flow at the dispenser Ice cubes coming out hollow, small, or misshapen from insufficient water fill Valve buzzing or humming without opening Primary valve tests fine but the refrigerator still won't dispense water or make ice Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dual secondary water inlet valve directly replaces the following OEM and cross-reference part numbers: W10341320, WPW10341320, AP6019939, AWP49977, PD00004978, PS11753250, EAP11753250, 1937969, K-78032 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Note: the primary water inlet valve on many of these refrigerators is a different part (W10238100 / WPW10238100) — see the FAQ below on primary vs secondary valves. Compatibility This dual secondary water inlet valve is compatible with select side-by-side refrigerators from the following brands: Whirlpool side-by-side refrigerators — select models (verify with parts diagram) Maytag side-by-side refrigerators — MSB26C6MDE00/DE02, MSB26C6MDH00/DH02, MSB26C6MDM00/DM02, MSB27C2XAB00, MSB27C2XAM00, MSB27C2XAW00, MSC21C6MDM00/DM02, MSC21C6MEZ00, MSC21C6MFZ00, MSS26C6MEZ00, MSS26C6MFB00/FB01, MSS26C6MFW00 and related models Jenn-Air side-by-side refrigerators — JSC23C9EEM00, JSC24C8EAM00/AM01/AM02 and related models KitchenAid side-by-side refrigerators — select models Amana, Magic Chef, Admiral, Norge, Roper side-by-side refrigerators — select Whirlpool-built models Kenmore / Sears side-by-side refrigerators — select Whirlpool-built models Important — This Is the SECONDARY Valve, Not the Primary: Many Whirlpool-platform side-by-side refrigerators use TWO water inlet valves: a primary valve (typically W10238100 / WPW10238100) where the household water line enters the refrigerator, and this dual secondary valve (W10341320) that splits flow between the dispenser and the ice maker. If your primary valve is functioning correctly but you're still not getting water or ice, the secondary valve is the likely culprit. Before ordering, confirm which valve your refrigerator's parts diagram calls for at the position you're replacing. Contact our support team with your model number if you're unsure. Key Features Original Equipment (OE) replacement — produced to the same design and performance standards as the factory part but not sold under the appliance brand's OEM label; provides the same fit and function at a more affordable price Dual secondary water inlet valve — supplies water to both the refrigerator's water dispenser and the ice maker Dual-solenoid design: each solenoid opens independently when the control board calls for water at that destination Electrical specs: 110/120V, 50/60Hz · W1 = 20W, W2 = 35W Resolves "no water through door," "ice maker doesn't make ice," "too little ice," and "leaking at connections" symptoms Common fix for leaks at the valve's water line connections Replaces WPW10341320, AP6019939, PS11753250, EAP11753250, 1937969, and K-78032 Compatible with Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore side-by-side refrigerators Note: this is the SECONDARY valve — the primary water inlet valve is a different part (W10238100) DIY repair — installs in about 30 minutes with basic hand tools and novice repair experience Product Specifications Part Number W10341320-OE Designation OE (Original Equipment) OEM Part Number WPW10341320 Part Type Refrigerator Dual Secondary Water Inlet Valve Condition OE Replacement Application Side-by-Side Refrigerators (Whirlpool platform) Valve Position SECONDARY (not the primary inlet valve) Solenoids Dual — W1 = 20W, W2 = 35W Voltage 110/120V Frequency 50/60 Hz Supplies Water To Water dispenser + Ice maker Related Part Primary Water Inlet Valve (W10238100 / WPW10238100, sold separately) Compatible Brands Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, Kenmore Installation Notes ⚠️ Unplug Refrigerator and Shut Off Water Supply Before Starting — Wear Work Gloves Unplug the refrigerator (or shut off the house circuit breaker for the appliance) and turn off the refrigerator's water supply at the shutoff valve before beginning. Wear work gloves to protect your hands. Safely store any food that could spoil during the repair. Have towels ready — residual water remains in the lines and will spill when disconnected. Pull the refrigerator away from the wall to access the rear. The secondary water inlet valve is typically mounted at the back of the refrigerator, downstream of the primary valve where the household water line enters. Photograph the water line and wire harness connections before disconnecting anything — with two solenoids and multiple water lines, correct reconnection matters. Disconnect the water lines from the valve (use a 1/2" wrench where needed) and catch any residual water with a towel. Disconnect the electrical connectors from both solenoids. Remove the mounting screws holding the valve bracket in place and lift out the old valve. Install the new W10341320 (OE) valve in the same position and orientation, secure the mounting hardware, and reconnect the water lines — tighten fittings snugly without over-torquing. Reconnect the electrical connectors to the correct solenoids, matching your photos. Turn the water supply back on and check every connection for leaks BEFORE pushing the refrigerator back into place. Restore power. Run water through the dispenser for a few minutes to purge air from the lines, and discard the first few batches of ice. Tools needed: Multi-screwdriver, 1/2" wrench, nut driver, towels, work gloves. Frequently Asked Questions What does "OE" mean and how is it different from Genuine OEM? OE (Original Equipment) parts are produced to the same design and performance standards as the original factory part, but they are not sold under the appliance brand's OEM label. They provide the same fit and function as the OEM part at a more affordable price. The W10341320 (OE) water inlet valve matches the electrical specifications (110/120V, 50/60Hz, dual solenoid W1=20W / W2=35W), dual-secondary valve design, connections, and physical fit of the original Whirlpool OEM part, and installs identically. The main difference from a Genuine OEM Whirlpool part is the branding and warranty — the OE version delivers equivalent performance without the OEM price premium. What's the difference between the primary and secondary water inlet valve? Many Whirlpool-platform side-by-side refrigerators use two water inlet valves working in series. The primary valve (typically W10238100 / WPW10238100) is where the household water supply line first enters the refrigerator — it's the main gatekeeper for water entering the appliance. The secondary valve (this W10341320) sits downstream and splits that flow between the water dispenser and the ice maker via its two independent solenoids. Both can fail independently. The key diagnostic: if the primary valve is working correctly (water is reaching the refrigerator) but you're still not getting water at the dispenser or ice from the ice maker, the secondary valve is the likely culprit. Check your model's parts diagram to confirm which valve you need. My water dispenser works but the ice maker doesn't — can this still be the valve? Yes, absolutely. This is a dual-solenoid valve — one solenoid feeds the water dispenser, the other feeds the ice maker. They fail independently. If your dispenser works fine but the ice maker isn't getting water (no ice, or hollow/small cubes), the ice maker solenoid on this valve may have failed while the dispenser solenoid still works. The reverse is also true. Before replacing the valve, also verify the ice maker itself is turned on (check the wire signal arm position) and that the water line to the ice maker isn't frozen or kinked — those produce similar symptoms. Is this a common fix for leaks? Yes — leaks at the water inlet valve's connections are one of the most common reasons this part gets replaced. Over time, the valve body or its fittings can develop cracks or the internal seals can degrade, producing a slow drip that pools behind or under the refrigerator. If you've found water behind your fridge and traced it to the valve area, replacing the valve typically resolves it. When installing the new valve, tighten the water line fittings snugly but don't over-torque them — over-tightening can crack the fitting and create a new leak. Always check all connections for leaks before pushing the refrigerator back against the wall. Should I flush the water lines after installing the new valve? Yes. After the new valve is installed and the water supply is restored, run water through the dispenser for several minutes to purge trapped air from the lines — air pockets cause sputtering and inconsistent flow. Also discard the first two or three batches of ice the ice maker produces, since they may contain air, debris, or residual manufacturing material from the new valve. After that, water and ice should return to normal quality and flow. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ OE (Original Equipment) Quality ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO W11224591 Refrigerator Evaporator Fan Motor The XPARTCO W11224591 is an aftermarket replacement freezer evaporator fan motor assembly compatible with a wide range of Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore bottom-mount French door refrigerators. The evaporator fan motor is located in the freezer compartment behind the rear panel — it draws cold air across the evaporator coils and circulates it throughout both the freezer and the fresh food compartment. This constant air movement is what keeps temperatures even and food fresh. When the fan motor fails, the most common symptom is telling: the refrigerator (fresh food) compartment stops cooling while the freezer stays cold but doesn't reach full capacity, because the fan is no longer moving the cold air up into the fridge section. This is a complete assembly that includes the fan motor, wiring harness, temperature sensor (thermistor), and defrost thermostat — everything integrated into one replaceable unit. Finished in white. As a direct replacement for the Whirlpool W11224591, it also replaces AP6329809, W10865431, W10728111, W11215582, 4844712, and PS12349521. Motor failure typically results from normal wear, obstruction from frost or debris rubbing the fan blade, or motor winding issues. Installs in 30–45 minutes with basic hand tools. Quick Answer The XPARTCO W11224591 Refrigerator Evaporator Fan Motor fixes Whirlpool, Maytag, KitchenAid, Jenn-Air, and Amana bottom-mount French door refrigerators where the fridge section is warm but the freezer is cold, temperatures are uneven, frost builds up on the coils, or unusual noise comes from the freezer compartment. Complete assembly — includes fan motor, wiring harness, temperature sensor, and defrost thermostat. White finish. Replaces AP6329809, W10865431, W10728111, W11215582, 4844712, PS12349521. Compatible with Whirlpool WRF757/WRF767/WRF736 series, KitchenAid KRFF507 series, Maytag MFT2574 series and related models. Common Problems This Part Fixes Refrigerator (fresh food) compartment warm while the freezer stays cold — the signature symptom of evaporator fan motor failure Uneven or inconsistent temperatures throughout the refrigerator Unusual noises from the freezer compartment — grinding, squealing, or clicking as the motor bearings fail or the blade rubs on frost/ice Frost or ice buildup around the cooling sections and evaporator coils Refrigerator running continuously or more frequently than usual to compensate for poor air circulation Noticeable decrease in overall cooling efficiency Food spoiling faster than normal in the fresh food compartment Fan motor not spinning at all when the compressor is running Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This evaporator fan motor assembly directly replaces the following OEM and cross-reference part numbers: W11224591, W10865431, 4844712, W10728111, W11215582, AP6329809, AWP43665, EAP11738038, FIX12349521, DLB5985WPEB, PD00052715, PS12349521. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This evaporator fan motor is compatible with select bottom-mount French door refrigerators from the following brands: Whirlpool refrigerators — WRF757SDHV00, WRF757SDHZ00/Z01/Z02, WRF767SDHV00/V02, WRF767SDHZ00/Z01/Z02 series Whirlpool refrigerators — WRF736SDAB14, WRF736SDAM14, WRF736SDAW14, 7WF736SDAM14 series KitchenAid refrigerators — KRFF507HPS00/PS01/PS02, KRFF507HBS02, KRFF507HWH02 series Maytag refrigerators — MFT2574DEH02 and related bottom-mount French door models Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper refrigerators — select Whirlpool-built models Kenmore / Sears and Ikea refrigerators — select Whirlpool-built models Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Complete evaporator fan motor assembly — includes fan motor, wiring harness, temperature sensor (thermistor), and defrost thermostat in one integrated unit Circulates cold air from the evaporator coils throughout the freezer and fresh food compartments for even temperatures Resolves the classic "fridge warm, freezer cold" symptom of evaporator fan failure Prevents frost buildup by maintaining proper airflow across the coils White finish, direct-fit replacement using original mounting points and connectors Because the assembly bundles the defrost thermostat and temperature sensor, it addresses multiple potential failure points in a single repair Replaces AP6329809, W10865431, W10728111, W11215582, 4844712, and PS12349521 Compatible with Whirlpool WRF757/WRF767/WRF736 series, KitchenAid KRFF507 series, Maytag MFT2574 series, plus Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, Kenmore, and Ikea Whirlpool-built bottom-mount refrigerators Aftermarket replacement built to OEM-equivalent quality standards DIY repair — installs in 30–45 minutes with basic hand tools Product Specifications Part Number W11224591 Part Type Freezer Evaporator Fan Motor Assembly Condition Aftermarket Replacement Application Bottom-Mount French Door Refrigerators (Whirlpool platform) Assembly Includes Fan Motor, Wiring Harness, Temperature Sensor (Thermistor), Defrost Thermostat Location Freezer compartment, behind rear panel Color White Compatible Brands Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, Kenmore, Ikea Installation Notes ⚠️ Unplug Refrigerator and Move Perishable Food Before Starting — Wear Work Gloves Unplug the refrigerator and safely store any food that could spoil while the power is off. Wear work gloves to protect your hands. The evaporator fan motor is located in the freezer compartment behind the rear access panel. Remove all freezer shelves, drawers, and the ice maker (if equipped) to clear access to the back wall. If there's frost or ice buildup on the rear panel or coils, allow the freezer to thaw completely before continuing — never chip or pry ice off the evaporator coils, as the aluminum fins damage easily. Remove the screws securing the rear freezer access panel and lift it away to expose the evaporator coils and fan motor assembly. Photograph the wiring harness connections and the fan motor orientation before disconnecting anything. Disconnect the wire harness connectors from the old assembly and release it from its mounting points. Lift out the old fan motor assembly. Install the new W11224591 assembly using the original mounting points and connectors — since this is a complete assembly, the fan motor, harness, temperature sensor, and defrost thermostat all transfer as one unit. Reconnect the wiring harness, matching your photos. Confirm the fan blade spins freely by hand without rubbing on any surrounding surface. Reinstall the rear access panel, shelves, drawers, and ice maker. Plug the refrigerator back in and allow several hours for the unit to return to its set temperature before reloading with food. Test airflow and temperature consistency before considering the job complete. Tools needed: Phillips screwdriver, 1/4" nut driver, work gloves. Frequently Asked Questions My refrigerator section is warm but the freezer is still cold — is this the fan motor? This is the single most common and telling symptom of a failed evaporator fan motor on these bottom-mount French door refrigerators. Here's why: the evaporator coils (which produce the cold) are in the freezer, and the evaporator fan is what pushes that cold air up into the fresh food compartment. When the fan motor fails, the freezer stays cold (it's right next to the coils) but the fridge section warms up because no air is being circulated to it. If your freezer is cold and your fridge is warm, the evaporator fan motor is the prime suspect. You can confirm by listening for the fan running when the compressor is on, or opening the freezer rear panel to see if the fan spins. What's included with this part — is it just the motor? This is a complete assembly, not just the bare motor. It includes the fan motor, the wiring harness, the temperature sensor (thermistor), and the defrost thermostat — all integrated into one unit. This is actually an advantage: since these components live together in the freezer compartment and can each cause cooling problems, replacing them as a bundle addresses multiple potential failure points in a single repair, reducing the chance you'll be back in the freezer compartment a few months later for a related part. Why is my evaporator fan making noise? A noisy evaporator fan usually means one of two things: the motor bearings are wearing out (producing grinding or squealing), or the fan blade is rubbing against frost or ice that has built up around it. If frost buildup is the cause, that often points to a secondary problem with the defrost system (defrost heater, thermostat, or control) allowing ice to accumulate where it shouldn't. Since this replacement assembly includes a new defrost thermostat, it addresses one of the common defrost-related causes. If heavy frost keeps returning after replacement, the defrost heater or control board should be investigated next. Do I need to defrost the freezer before installing this? If there's frost or ice buildup on the rear freezer panel or evaporator coils, yes — clear it before installing the new assembly. Leave the freezer empty and unplugged with the door open for several hours (longer for heavy ice) to let everything thaw naturally, placing towels at the base to catch melt water. Never chip or pry ice off the evaporator coils with a tool — the aluminum fins are delicate and a damaged coil is a far more expensive repair. Once everything is fully thawed and dried, proceed with the fan motor replacement. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured to match the fit, mounting points, connector configuration, and function of the original W11224591 evaporator fan motor assembly used in compatible Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, and Kenmore bottom-mount French door refrigerators — including the integrated harness, temperature sensor, and defrost thermostat. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

ERP 8561996 Dishwasher Upper Rack Adjuster Wheel Replaces part Numbers: W11157084, WP8561996, 8561996, AP6285708, PS12347743, W10889280, ER8561996   This is an aftermarket part that can be used as a replacement for the OEM part. California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

EAU61524007 Genuine OEM LG Refrigerator Evaporator Fan Motor The EAU61524007 is a genuine LG OEM evaporator fan motor for LG and select Kenmore refrigerators. This motor circulates air over the evaporator coil and distributes that cooled air into the fresh food and freezer compartments in a balanced way, which is what keeps temperatures even throughout the refrigerator and helps prevent frost from building up on the coil. DC-powered, white in color, with an assembled height of approximately 1 inch. Over time, the motor's bearings can wear out, or general electrical failure can set in from years of continuous cycling. A failing evaporator fan motor produces a wide range of symptoms since it affects both compartments and the defrost system: the refrigerator may not start at all, either compartment may run too warm or too cold, or frost buildup may appear where it shouldn't. Unusual noise from the freezer is another common early sign of a struggling motor. It directly replaces EAU60694510, AP5950081, PS10058947, EAP10058947, and PD00006349. Quick Answer The EAU61524007 Genuine OEM LG Refrigerator Evaporator Fan Motor fixes LG and select Kenmore refrigerators that won't start, run too warm or too cold in either compartment, or show frost buildup where it shouldn't be. DC motor, white, approx. 1" assembled height. Replaces EAU60694510, AP5950081, PS10058947, EAP10058947, PD00006349. Not the same as the similarly-numbered EAU61524002 motor (DC13V, 0.265A, 3.5W) — confirm you have the exact number before ordering. Common Problems This Part Fixes Refrigerator won't start Refrigerator compartment running too warm Refrigerator compartment running too cold Freezer compartment running too warm Freezer compartment running too cold Frost buildup where it shouldn't be occurring Unusual noise from the freezer indicating a struggling fan motor Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This refrigerator evaporator fan motor directly replaces the following OEM and cross-reference part numbers: EAU61524007, EAU60694510, 3286319, AP5950081, EAP10058947, PS10058947, ALG54568, PD00006349 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This evaporator fan motor is compatible with select LG refrigerators, and also fits select Kenmore and Kenmore Elite refrigerators built on the LG platform, including model numbers such as LFX31915SW, LFX25992ST, and GRL318LSJP. Note — not the same as EAU61524002: A similarly-numbered part, EAU61524002, is a separate LG evaporator/freezer fan motor rated DC13V, 0.265A, 3.5W, used on different models. Always verify your full model number and match the exact part number before ordering. Contact our support team with your model number if you're unsure which motor your refrigerator needs. Key Features Genuine LG OEM part — factory-specified motor design and airflow performance Circulates air over the evaporator coil and distributes it evenly to both compartments Resolves "won't start," "running too warm or too cold," and "frost buildup" symptoms caused by fan motor failure DC-powered motor White finish, approximately 1" assembled height Direct drop-in replacement matching the original mounting and blade fitment Replaces EAU60694510, AP5950081, PS10058947, EAP10058947, and PD00006349 Compatible with LG and select Kenmore refrigerators Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number EAU61524007 Part Type Refrigerator Evaporator Fan Motor Condition Genuine OEM Brand LG Function Circulates air over the evaporator coil to both compartments Power Type DC Color White Assembled Height Approx. 1 in. Quantity 1 fan motor Compatible Brands LG, Kenmore, Kenmore Elite Installation Notes ⚠️ Unplug Refrigerator Before Starting Disconnect power at the outlet before beginning, and move perishable food to a cooler for the duration of the repair. Wear work gloves. Access is typically through the freezer's rear interior panel: remove shelving and bins as needed, then remove the screws securing the back panel to expose the evaporator coil and fan assembly. If there's significant frost or ice around the fan or coil, let the unit sit unplugged with the door open for a few hours, or run a manual defrost, before continuing. Photograph the wiring harness connector and the fan blade's orientation before disconnecting anything. Unplug the wiring harness connector from the old motor, remove the mounting screws or clips holding the motor bracket in place, and pull the motor and fan blade assembly free. Transfer the fan blade to the new motor if a blade isn't included, matching the original orientation. Mount the new EAU61524007 in the same position, reconnect the wiring harness connector fully, and confirm the blade spins freely by hand without contacting the housing before reassembling the back panel. Restore power and monitor both compartments over the next 24 hours to confirm even, consistent cooling has returned. Tools needed: Phillips screwdriver, work gloves. Frequently Asked Questions My refrigerator won't start at all. Could this really be the fan motor? Yes, this is one of the documented symptoms for this part on LG's own service guidance. Because this motor is tied into the refrigeration and defrost circuit, a failure here can present as the unit not starting at all, in addition to the more expected symptoms like temperature problems or noise. That said, other components can produce a similar no-start symptom, so it's worth confirming this diagnosis if you're not fully certain. Both compartments are running warm, not just one. Does that still point to this motor? Yes. Since this motor is responsible for distributing cooled air to both the fresh food and freezer compartments from the evaporator coil, a failure here can affect both areas simultaneously rather than just one, unlike some other fan motor designs that mainly affect the compartment further from the coil. How do I make sure I'm ordering this exact motor and not a similar one? Check the part number printed directly on your old motor if it's legible, or confirm your refrigerator's full model number against the compatibility list. LG has released similarly-numbered motors, such as EAU61524002, that serve different models and have different electrical specifications, so matching by number is more reliable than matching by general appearance. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by LG to factory specifications — guaranteed fit, materials, and performance. It matches the original motor design, blade fitment, and mounting configuration of the evaporator fan motor originally installed in your refrigerator. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

6601EN1003D Washer Door Lock Interlock Switch Replaces Part Numbers: 6601EN1003D, 6601ER1005A, 2651099, AH3636296, AP5594317, EA3636296, PS3636296.   This is an aftermarket part that can be used as a replacement for the OEM part. WARNING: California’s Proposition 65 (California Residents Only)

Read more less

12002782 Refrigerator Genuine OEM Overload Relay Kit Replaces Part Numbers: 12002782, 1194680, 61005518, AH2004057, EA2004057, OEM12028982, AP4009659, PS2004057. Description: This is a Genuine OEM compressor overload and relay kit for Specific Whirlpool, Maytag, Kenmore Refrigerator models. Kit was recently redesigned by manufacturer.   California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

XPARTCO MHY62044106 Refrigerator Door Mullion Spring - Compatible with LG, Kenmore Refrigerators Product Description Restore proper sealing in your refrigerator with the replacement MHY62044106 Refrigerator Door Mullion Spring. This high-quality spring, designed for LG and Kenmore French-door refrigerators, ensures the mullion flap closes securely, maintaining an airtight seal between the doors to prevent energy loss and maintain cooling efficiency. Made of heavy-duty steel with a clockwise winding and 6 coils, this spring fits into the mullion hinge to resolve issues like doors not closing properly, mullion flap misalignment, or beeping alarms. Note: Includes one spring. Disconnect power before installation. Replaces part numbers: MHY62044106, 2676261, MHY62044104, PD00035635, EAP6012670, AP5657415, PS6012670 Compatibility: Compatible with models including but not limited to: LG: LFC25765ST, LFX21976ST, LFX25973ST, LFX25976ST, LFX25978SB, LFX25978ST, LFX25991ST, LFX28968SB, LFX28968ST, LFX28978SB, LFX28978ST, LFX28979ST, LFX31925SB, LFX31925ST, LFX31935ST, LFX31945ST, LMX28988ST, LMX31985ST Kenmore: 795.71054.010, 795.71056.011, 795.71063.011 Other LG models: GF-B620BSL, GF-B620PL, GF-D613SL, GF-L613PL, GM-F208ST, GR-L218ASL, GR-L218CSL Verify your model number or contact our support team for assistance. Key Features: ✅ Brand and Models Compatibility: Fits select LG and Kenmore French-door refrigerator models. 🔥 Specifications: replacement mullion spring, clockwise wound, 6 coils, heavy-duty steel, approximately 1-1/8" long, two legs (one shorter for door side), corrosion-resistant. 💰 Cost-Effective Alternative: replacement spring offers OEM-equivalent performance at a lower price. 🛠️ Easy Installation: Requires Phillips screwdriver, flathead screwdriver, pliers, work gloves; typically installed in 15–30 minutes. 🛡️ Reliable Fixes: Resolves doors not closing, mullion flap misalignment, beeping alarms, or cooling inefficiencies. Installation Notes: Safety First: Disconnect the refrigerator from the power source before installation. Shop Parts-O-Matic for high-quality replacement appliance parts with a 30-day return policy. Ensure your refrigerator seals perfectly today! Add to cart now for a budget-friendly fix!

Read more less

Genuine Whirlpool OEM Part Whirlpool W10918010 Refrigerator Door Closer - Gray (Right Hand) Right-hand gray refrigerator door closer for the door hinge and closing assembly. Quick Answer W10918010 is a genuine Whirlpool OEM right-hand gray refrigerator door closer. It works with the door hinge and closure mechanism to help guide the refrigerator door into its proper closed position and replaces earlier part number W10833739. Product Description The W10918010 door closer works with the refrigerator door hinge and closing mechanism to guide the right-hand fresh-food door through the final portion of its closing movement. The shaped closer surface helps the door settle into its intended closed position as the hinge moves. A cracked or worn closer can cause the door to close unevenly, need extra force near the end of travel, or fail to settle into position correctly. A door that remains partially open can allow cold air to escape, which may contribute to temperature problems, condensation, frost, and longer compressor run time. Symptoms This Part Fixes Right-hand refrigerator door does not close smoothly Door needs an extra push near the fully closed position Door feels uneven or shifts as it closes Auto-closing action is weak or inconsistent Original closer is visibly cracked, worn, or broken Door does not settle securely into its normal closed position Replaces Part Numbers Use these verified numbers to identify the correct replacement: W10918010, W10833739, 4461321, AP6038208, AWP42677, EAP11770045, PD00073761, PS11770045 Cross-reference numbers are listed for identification only. This listing ships the genuine Whirlpool OEM part. Compatibility Fits select Whirlpool-built refrigerators that specify part number W10918010, including the following verified model examples: WRF532SNHZ06 · JFC2089BEP07 · MFC2062FEZ08 · WRF535SMHZ06 · KRFF302ESS05 · MFI2570FEZ12 · WRF535SWHZ06 · KRFF302EWH04 · WRFA35SWHZ06 · WRF535SMHZ07 ⚠️ Important: This is the right-hand gray door closer. Always verify your refrigerator's complete model number, door side, and original part number before ordering. Contact our support team if you're unsure. Key Features Genuine Whirlpool OEM replacement part Manufacturer part number W10918010 Right-hand refrigerator door position Gray finish Replaces previous part number W10833739 Designed for the refrigerator door closing and hinge assembly Product Specifications Part Number W10918010 Brand Whirlpool Part Type Refrigerator Door Closer Assembly Refrigerator Door / Hinge Closing Assembly Position Right Hand Color Gray Function Helps guide the refrigerator door into the closed position Part Quality Genuine Whirlpool OEM Condition New Installation Notes Disconnect refrigerator power before service. Support the refrigerator door before loosening or removing hinge-related hardware. Confirm that the existing closer is on the right-hand side and matches W10918010 or previous part number W10833739. Inspect the closer, hinge, mounting points, and nearby hardware for cracks, wear, looseness, or deformation. Remove the original closer while noting its installed position and orientation. Install W10918010 in the same right-hand position. Reassemble the hinge hardware and verify that the door opens, aligns, and closes normally. ⚠️ Diagnostic tip: Poor door closing can also be caused by worn hinge components, loose hardware, cabinet leveling problems, or gasket interference. Inspect the complete door system before replacing only the closer. Frequently Asked Questions What does Whirlpool W10918010 do? W10918010 is the right-hand refrigerator door closer. It works with the door hinge and closing mechanism to help guide the door through the final portion of its travel and into the proper closed position. Is W10918010 a genuine Whirlpool OEM part? Yes. W10918010 is documented as a genuine Whirlpool OEM refrigerator door closer. It is also used on select Whirlpool-built appliance brands and models. How can I check whether the door closer is actually damaged? Open the right-hand refrigerator door and slowly move it through the final portion of closing while watching the lower hinge and closer area. If the closer is visibly cracked, broken, deformed, loose, or fails to move smoothly while the hinge hardware remains secure, the closer may need replacement. Does the right-hand position matter? Yes. W10918010 is specifically identified as the right-hand gray door closer. The matching left-hand closer is a different part, so verify the door side and complete appliance model before ordering. Why should I match the model number instead of comparing the part visually? Door closers can look very similar while having different geometry, mounting points, colors, or left/right orientation. Matching the complete refrigerator model and manufacturer part number is more reliable than appearance alone. What should I inspect while replacing the closer? Inspect the hinge, mounting hardware, door alignment, and gasket contact while the door is supported. If another closure component is worn or loose, replacing the closer alone may not fully correct the door problem. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

WR60X26866 Genuine OEM GE Refrigerator Axial Evaporator Fan Motor The WR60X26866 is a Genuine OEM GE replacement axial evaporator fan motor manufactured by GE to factory specifications, designed as a direct fit for the fresh food section of select GE French door refrigerators, including the CFE28, CFE29, CWE23, CYE22, CYE23, DFE28, DFE29, GFD28, GFE26, GFE27, GFE28, GFE29, GFS26, GFS28, GNE26, GNE29, GYE22, GYS22, PFD28, PFE28, PFE29, PWE23, PYD22, PYE22, PYE23, and ZWE23 series. The evaporator fan motor pulls air through the evaporator coils to remove heat from the circulating air inside the refrigerator. Without a functioning evaporator fan, the refrigerator compartment cannot maintain its target temperature even when the compressor and condenser are running normally — the cold air generated at the evaporator simply isn't being circulated to the food storage areas. The WR60X26866 is a DC motor rated at 13.6V DC, 0.16A, with a fan housing measuring 3-4/7"L x 2"W x 3-1/8"H, plus a multi-color wire harness and plug approximately 11-1/2" long. It includes the axial fan blade and harness as a complete assembly. It directly replaces WR60X26033, WR60X26030, WR60X24303, WR60X10341, WR60X10356, WR60X10357, WR02X13733, 239D1412P006, V80E14MS2A3-57A611, 8817V-W1, 4546026, AP5985039, AP6278228, EAP12172983, PD00038765, PS11721915, and PS12172983. Important: if your refrigerator was built between May 2014 and March 2015 with serial range FF–HD, the unit's software must be updated before installing this fan motor — see FAQ below. Installs in 20–30 minutes with basic hand tools. Quick Answer The WR60X26866 Genuine OEM GE Refrigerator Axial Evaporator Fan Motor fixes GE French door refrigerators where the fridge isn't cooling but the freezer is cold, the evaporator coils are frosted over, the ice maker isn't working due to insufficient cooling, or there's loud humming or grinding from the freezer area. Axial fan motor, 13.6V DC, 0.16A. Fan housing: 3-4/7"L x 2"W x 3-1/8"H; harness ~11-1/2"L. Replaces WR60X26033, WR60X26030, WR60X24303, WR60X10341, WR60X10356, WR60X10357, WR02X13733, 239D1412P006, V80E14MS2A3-57A611, 8817V-W1, 4546026, AP5985039, AP6278228, EAP12172983, PD00038765, PS11721915, PS12172983. Note: May 2014 – Mar 2015 build refrigerators (serial range FF–HD) require a software update before installation. Common Problems This Part Fixes Refrigerator not cooling properly while the freezer remains cold — classic evaporator fan failure Freezer cold but fridge warm — fresh food compartment air not being circulated Frosty or frozen evaporator coils due to insufficient air circulation Ice maker failure caused by inadequate cooling in the compartment Loud humming, grinding, or buzzing noise from the freezer or fresh food compartment Refrigerator running continuously without reaching set temperature Fan blade not spinning freely or seized when checked by hand Multimeter shows no continuity through the motor windings Replaces Part Numbers This evaporator fan motor directly replaces the following OEM and cross-reference part numbers: WR60X26866, WR02X13733, WR60X10341, WR60X10356, WR60X10357, WR60X24303, WR60X26030, WR60X26033, V80E14MS2A3-57A611, 8817V W1, 239D1412P006, PD00038765, FIX12172983, AGE29673, AP6278228, PS12172983. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This evaporator fan motor is compatible with select GE French door refrigerators, including: GE refrigerators — CFE28, CFE29, CWE23, CYE22, CYE23 series (CFE28TP2MBS1, CFE28USHNSS, CWE23SP2MBS1, CYE22TP2MBS1 and related) GE refrigerators — DFE28, DFE29 series (DFE28JELCDS and related) GE refrigerators — GFD28, GFE26, GFE27, GFE28, GFE29 series (GFD28GBLBTS, GFE26GGHEBB and related) GE refrigerators — GFS26, GFS28, GNE26, GNE29 series GE refrigerators — GYE22, GYS22 series (GYE22HMKEES and related) GE refrigerators — PFD28, PFE28, PFE29 series (PFE28KELFDS and related) GE refrigerators — PWE23 series (PWE23KSKDSS and related) GE refrigerators — PYD22, PYE22, PYE23 series (PYE22KSKBSS and related) GE refrigerators — ZWE23 series and select related Café and Profile French door models Important — Software Update Requirement: If your GE refrigerator was manufactured between May 2014 and March 2015 with a serial number in the range FF–HD, the refrigerator's control software must be updated by GE factory service (or via Software Update Module WR98R882802) before installing this fan motor. Installing the new motor without the software update on these affected units may result in improper performance. Check your refrigerator's serial number plate before ordering. Key Features Axial evaporator fan motor for the fresh food section of GE French door refrigerators Pulls air through the evaporator coils to remove heat and circulate cold air through the refrigerator compartment DC motor — rated 13.6V DC, 0.16A — runs on DC voltage from the refrigerator control board Includes the axial fan blade and pre-attached multi-color wire harness with plug Fan housing dimensions: 3-4/7"L x 2"W x 3-1/8"H; harness and plug approximately 11-1/2" long Quiet operation — engineered to minimize hum and vibration in the refrigerator cabinet Plastic and metal construction, black housing with multi-color harness Replaces an extensive list of GE part numbers including WR60X26033, WR60X26030, WR60X24303, WR60X10341, WR60X10356, WR60X10357, and additional cross-references Compatible with GE, GE Café, and GE Profile French door refrigerators in the CFE, CWE, CYE, DFE, GFD, GFE, GFS, GNE, GYE, GYS, PFD, PFE, PWE, PYD, PYE, and ZWE series Genuine OEM part manufactured by GE to factory specifications — guaranteed fit and performance DIY repair — installs in 20–30 minutes with basic hand tools Product Specifications Part Number WR60X26866 Part Type Refrigerator Evaporator Fan Motor (Fresh Food / Axial) Condition Genuine OEM Application GE French Door Refrigerators Voltage 13.6V DC Amperage 0.16A Fan Type Axial Fan Housing Dimensions 3-4/7"L x 2"W x 3-1/8"H Harness Length Approximately 11-1/2 inches Color Black housing with multi-color harness Material Plastic / Metal Includes Axial fan motor assembly with harness Software Update Required For May 2014 – Mar 2015 builds (serial range FF–HD) — use WR98R882802 Compatible Brands GE, GE Café, GE Profile Installation Notes ⚠️ Unplug Refrigerator and Move Perishable Food Before Starting — Wear Work Gloves Unplug the refrigerator and safely store any food that could spoil while the power is off. Wear work gloves to protect your hands. The evaporator fan motor for the fresh food section is mounted on the back wall of the fresh food (refrigerator) compartment, behind an access panel. Take a photo of the existing fan position and wire harness routing before disconnecting. Remove the shelves and any internal components blocking access to the back wall, then remove the screws holding the rear access panel in place. Disconnect the fan motor's wire harness connector and remove the mounting screws securing the old motor. Note the fan blade orientation on the motor shaft. Install the new WR60X26866 motor assembly in the same position with the blade facing the same direction, reconnect the wiring harness, and reinstall the mounting screws and access panel. Replace the shelves and other internal components, restore power, and confirm the fan spins and the refrigerator cools properly. Allow several hours for the refrigerator to return to its set temperature before reloading with food. Tools needed: Phillips screwdriver, 1/4" nut driver, work gloves. Frequently Asked Questions My fridge is warm but my freezer is cold — is the evaporator fan motor the problem? Yes — this is one of the most recognizable symptoms of evaporator fan motor failure on GE French door refrigerators with a separate fresh food evaporator. The freezer side has its own cooling circuit and remains cold, while the fresh food side relies on this fan to circulate air across its evaporator coils. When the fan fails, the freezer continues working but the fresh food compartment loses its cold air supply, warming up while the freezer stays at temperature. If you also notice frost building up on the evaporator coils behind the back panel of the fresh food compartment, the fan failure is confirmed. What is the software update requirement for May 2014 – March 2015 refrigerators? GE issued a software update for certain refrigerators manufactured between May 2014 and March 2015 (serial range FF–HD) before they could properly support newer revisions of the WR60X26866 evaporator fan motor. If your refrigerator falls in this date and serial range, the control software must be updated before installing this fan motor — either by GE factory service or by using the Software Update Module part WR98R882802. Installing the new fan on an unupdated unit can result in improper performance. Check the serial number plate inside your refrigerator (typically on the left side wall) to confirm whether your unit is affected. Refrigerators built outside this range do not require the update. How do I test if the evaporator fan motor has failed? Unplug the refrigerator, then access the fan behind the rear panel of the fresh food compartment. First, try turning the fan blade by hand — if it doesn't spin freely, is stiff, or seizes, the motor bearing has failed. Next, listen during normal operation — if the motor is unusually noisy or makes a grinding sound, the bearings are worn even if it still spins. Finally, with the unit unplugged and the motor disconnected, use a multimeter on the motor windings to check for continuity. If the windings show no continuity, the motor has failed electrically. Also check for approximately 11–14V DC at the connector when the refrigerator is running — if voltage is present but the motor doesn't spin, the motor has failed. My fridge has two evaporator fans — which one does this replace? Some GE French door refrigerators have separate evaporator fan motors for the freezer and the fresh food sections. The WR60X26866 is the fresh food evaporator fan motor — it's the axial fan located behind the rear panel of the fresh food compartment, not in the freezer. If your symptom is "freezer cold, fridge warm," this is the correct part. If your symptom is "freezer warm" or "ice maker not making ice but fridge is fine," the freezer evaporator fan motor (a different part number) is more likely the cause. Confirm which compartment has the cooling problem before ordering. Is this an OEM or aftermarket part? This is a Genuine OEM part manufactured by GE to factory specifications. It is the exact same axial evaporator fan motor installed in compatible GE, GE Café, and GE Profile French door refrigerators from the factory — guaranteed fit, materials, and performance. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Genuine OEM Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

W11230103 Dishwasher Sump Pump and Motor Replaces Part Numbers:  W11230103, W10620220, 4591207, AP6329759, PS12349660.  Description: This Pump & Motor is an OEM part for Whirlpool dishwasher models. It serves as the heart of the wash system by providing water circulation and spray throughout all cycles. The pump circulates water mixed with detergent to clean dishes effectively.    California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less