Search results for "dishwasher dispenser"

WR57X30890 Refrigerator Genuine Water Valve Water inlet valve assembly with Wire Harness Replaces Part Numbers: WR57X30890, WR57X26569, WR57X30891, AP6891693, PS12727426. Description: This water inlet valve is a Genuine OEM part for select GE Refrigerator models, responsible for controlling the flow of water into the refrigerator's ice maker and water dispenser. It is typically located at the back of the appliance, near the water supply line. The water inlet valve features quick-connect fittings for easy installation and ensures a reliable and steady supply of water for ice production and dispensing.  

Read more less

XPARTCO 5221ER1003S Washer Water Valve The XPARTCO 5221ER1003S is an aftermarket replacement cold water inlet valve for LG and select Kenmore front-load washers. This valve sits underneath the top panel, at the point where the cold water supply hose connects, and it's the gatekeeper for cold water entering the tub. When the control calls for a cold fill, it energizes the valve's solenoid to open, admitting water; once the correct level is reached, it closes again. This part controls the cold water side specifically — hot fills on these washers are governed by a separate valve. Rated 12V and terminated with small male spade connectors, this valve measures approximately 4.75"H x 3.25"W x 2.25"L, with a gray plastic and metal housing. Over time, rust and mineral buildup inside the valve body — a documented failure point on this platform — can prevent it from sealing fully, which lets water continue flowing even after the valve is told to close. A washer that keeps filling even while draining, or that leaks steadily at the cold connection, is a strong sign of exactly this kind of stuck-open valve failure. Other failure modes include a burned-out solenoid coil and general wear from age. It directly replaces 4869496, AP6798394, PS12587936, and EAP12587936, and is also cross-referenced to the related 5221ER1003A part number. Quick Answer The XPARTCO 5221ER1003S Washer Water Valve fixes LG and select Kenmore front-load washers where cold water won't fill, fills slowly, keeps filling continuously (even while draining), or leaks at the water connection. 12V cold water inlet valve, small male spade terminals, 4.75"H x 3.25"W x 2.25"L. Replaces 4869496, AP6798394, PS12587936, EAP12587936. Rust and mineral buildup inside the valve body is a documented cause of it sticking open — check for rust at the connection before you order. Common Problems This Part Fixes Washer won't fill with cold water at the start of the cycle Cold water fills much more slowly than it used to Washer keeps filling continuously, even while water is simultaneously draining out Water leaking steadily at the cold water connection point Visible rust or mineral buildup around the valve body or connection Cycle stalling at the fill step and never advancing to wash Water pooling underneath or behind the washer near the cold supply line Cold wash or cold rinse cycles specifically affected while other cycles run fine Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer cold water inlet valve directly replaces the following OEM and cross-reference part numbers: 5221ER1003S, 5221ER1003A, 4869496, AP6798394, PS12587936, ALG51905, PD00057211, EAP12587936 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This cold water inlet valve is compatible with select LG front-load washers, and also fits select Kenmore front-load washers built on the LG platform, including model numbers such as: LG WM4000HBA, WM4000HWA, WM3400CW, WM3470CW LG W3600HVA Kenmore WKE100HVA (select LG-built models) Note — cold side only: This is the cold water valve. Some LG front-load washers use a separate hot water valve for the hot supply connection — if hot water fills normally but cold does not, this valve is the correct part; if the issue affects both hot and cold fills, the problem may lie elsewhere in the fill circuit. This valve is specific to LG's front-load platform and is not intended for top-load washers. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Aftermarket replacement cold water inlet valve for LG and select Kenmore front-load washers Resolves "won't fill with cold water," "fills slowly," "keeps filling continuously," and "leaking at the connection" symptoms caused by valve failure Rated 12V with small male spade terminal connections for a secure electrical fit Gray plastic and metal housing, approximately 4.75"H x 3.25"W x 2.25"L Direct drop-in replacement — mounts underneath the top panel at the original connection point Replaces 4869496, AP6798394, PS12587936, and EAP12587936 Compatible with LG and select Kenmore front-load washers Aftermarket replacement built to OEM-equivalent quality standards Straightforward DIY repair using basic hand tools Product Specifications Part Number 5221ER1003S OEM Part Number 5221ER1003S (also 5221ER1003A) Part Type Washer Water Inlet Valve — Cold Condition Aftermarket Replacement Brand LG Application Front-Load Washers Voltage 12V Electrical Connection Small male spade terminals Color Gray Material Plastic and metal Height 4.75 in. Width 3.25 in. Length 2.25 in. Location Underneath the top panel, dispenser and control panel assembly Quantity 1 valve Compatible Brands LG, select Kenmore Installation Notes ⚠️ Shut Off Water Supply And Unplug Washer Before Starting — Have A Towel Ready Unplug the washer and shut off the cold water supply valve before beginning. Wear work gloves. Pull the washer away from the wall for access. Unthread the cold water supply line from the back of the valve first — have a towel ready, since residual water will spill out. Unthread the two screws securing the top panel, then slide the panel back and lift it off to access the valve assembly underneath. Photograph the wiring connections before disconnecting anything. Disconnect the spade terminal wire connectors from the old valve, remove its mounting screw or bracket, and pull the valve free. While it's out, inspect the area for rust or mineral scale, and clean the connection point if needed before installing the new valve. Install the new 5221ER1003S in the same position, reconnect the spade terminals, and secure the mounting hardware. Rethread the cold water supply line onto the new valve, tightening securely. Reinstall the top panel and its two screws. Restore the water supply and power, then run a short cycle and confirm the tub fills at the normal rate with no leaking underneath or behind the washer. Tools needed: channellock pliers, flathead screwdriver, pliers, drill/driver with a Phillips bit, towel, work gloves. Frequently Asked Questions My washer keeps filling even while it's draining. Is that this valve? Yes, this is a well-documented failure mode on this platform. Rust and mineral buildup inside the valve body can prevent it from sealing fully closed, so water keeps trickling or flowing into the tub even after the fill portion of the cycle has ended — sometimes enough to keep pace with draining, making it look like the washer is filling and draining simultaneously. If you open up the top panel and see rust around the valve, that strongly confirms this diagnosis. Cold water won't fill but hot water works fine. Is this the right part? Yes — this valve controls cold water specifically, and some LG front-load washers use a separate valve for the hot supply. If cold-specific cycles are failing while hot water fills normally, this cold valve is the correct part to replace. I see rust on my old valve but it isn't leaking yet. Should I still replace it? It's worth strongly considering. Rust and mineral buildup on this valve is a known precursor to it sticking partially open, which can lead to continuous filling, water waste, and potential water damage if it isn't caught. If you're already inspecting the area and see corrosion forming, replacing the valve proactively is often cheaper and easier than dealing with an active leak later. What's the difference between 5221ER1003S and 5221ER1003A? These are cross-referenced as the same valve — 5221ER1003A appears on some parts diagrams and listings as an alternate or prior designation for the identical part. If your washer's diagram shows either number, this listing is the correct replacement. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine LG OEM part, but is manufactured to match the 12V solenoid design, spade terminal connections, and dimensions of the original 5221ER1003S cold water valve used in compatible LG and Kenmore front-load washers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

5231JA2006F Refrigerator Water Filter Description: This water filter is designed to remove impurities from the water and ice dispensed by your refrigerator, providing clean and fresh-tasting water. It effectively reduces contaminants such as chlorine, lead, mercury, and other particulates, ensuring safe drinking water for you and your family.  You should replace this water filter if it becomes clogged or reaches the end of its usable life, typically every six months. Causes of a bad water filter can include normal usage leading to clogging, the accumulation of sediments and impurities over time, or damage to the filter casing. Failing to replace the filter regularly can also compromise its effectiveness. Cross Reference Number: 5231JA2006G, 5231JA2006F, AP6889576, PS12724531, LT600P, LT600P/PC/PCS

Read more less

WPW10238100 Refrigerator Genuine OEM Water Valve Replaces Part Numbers: WPW10238100, W10238100, W10498992, AP6017532, PS11750831. Description: This Genuine OEM Part is a single water inlet valve designed for use in select Whirlpool refrigerator models. Its key function is to supply water to the refrigerator's ice maker and water dispenser. When energized, this valve releases water from the supply line into the ice mold. If the water valve develops a crack, it will need replacement. The valve accommodates two different sizes of tubing: the smaller inlet measures 1/4", and the larger inlet measures 5/16".

Read more less

ERP W10498976 Refrigerator Water Valve Description: This replacement Part is a single coil water inlet valve intended for use in specific refrigerator models. The valve serves as a solenoid-operated switch that controls the release of water from the supply line into the ice maker mold when activated. This part is crucial to the proper functioning of the refrigerator's ice-making or water dispensing systems. Replaces Part Numbers: WPW10498976, W10498976, W10420082, AP6022334, PS11755667. 

Read more less

WH13X26637 Genuine OEM GE Washer Water Inlet Valve The WH13X26637 is a Genuine OEM GE replacement quad water inlet valve assembly compatible with select GE and GE Profile top-load washers in the GTW, GTV, GTN, PTW, and related series. This is a quad (4-solenoid) valve assembly that controls the flow of hot water, cold water, bleach dispenser water, and fabric softener dispenser water from the household supply lines into the washer tub and dispenser compartments. Each solenoid port is independently controlled by the washer's control board. When any port fails, the washer may not fill, fill too slowly, fill with the wrong temperature, overfill, fail to dispense bleach or fabric softener, or drip water between cycles. As a Genuine OEM part manufactured by GE to factory specifications, the WH13X26637 is a direct current-production replacement for the earlier WH13X24058. It measures approximately 7"L x 3"W x 3"H with multi-colored ports (blue, green, red, tan, silver, and gold) for easy identification of each solenoid's function. It directly replaces WH13X24058, WH13X26637-25PK, 4546358, AP6282070, EAP12171559, PD00037665, and PS12171559. Installs in 20–30 minutes with basic hand tools. Quick Answer The WH13X26637 Genuine OEM GE Washer Water Inlet Valve fixes GE top-load washers that won't fill, fill slowly, fill with wrong temperature, won't dispense bleach or fabric softener, overfill, or drip water between cycles. Quad (4-solenoid) valve. Approx. 7"L x 3"W x 3"H. Multi-color port identification. Genuine OEM. Replaces WH13X24058, WH13X26637-25PK, 4546358, AP6282070, EAP12171559, PS12171559. Compatible with GE GTW, GTV, GTN, PTW series top-load washers. Common Problems This Part Fixes Washer not filling with water at all when a cycle is started Washer filling very slowly — one or more solenoid ports partially blocked or failing Washer filling with only cold or only hot water — one temperature solenoid has failed Washer overfilling or filling continuously — valve port stuck open Bleach not dispensing during the wash cycle Fabric softener not dispensing at the rinse cycle point Water dripping into the tub between cycles — valve port not sealing completely Water leaking from the back of the washer near the valve body Replaces Part Numbers This water inlet valve directly replaces the following OEM and cross-reference part numbers: WH13X26637, WH13X24058, AGE26282, AP6282070, EAP12171559, PD00037665, PS12171559. WH13X26637 is the current updated part number superseding WH13X24058. If your washer's parts diagram shows WH13X24058, the WH13X26637 is the correct current replacement. Contact our support team with your model number if you need confirmation before ordering. Compatibility This water inlet valve is compatible with select GE and GE Profile top-load washers from the following series: GE washers — GTW680 series (GTW680BPL0DG, GTW680BPL1DG, GTW680BPL2DG, GTW680BSJ0WS, GTW680BSJ1WS, GTW680BSJ3WS, GTW680BSJ4WS, GTW680BSJ5WS, GTW680BSJ6WS and related models) GE washers — GTW685 series (GTW685BPL0DG, GTW685BPL1DG, GTW685BSL1WS, GTV685BSL0WS and related models) GE washers — GTW720 series (GTW720BPN0DG, GTW720BSN0WS and related models) GE washers — GTW725 series (GTW725BPN0DG, GTW725BSN0WS and related models) GE washers — GTW750 series (GTW750CPL0DG, GTW750CPL1DG, GTW750CSL0DG, GTW750CSL0WS, GTW750CSL1WS and related models) GE washers — GTW755 series (GTW755CPM0DG, GTW755CSM0WS, GTW755CSM1WS and related models) GE Profile washers — PTW600, PTW605, PTW700, PTW705 series and related models GE washers — GTN755 series (GTN755CPM1DG and related models) Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Genuine OEM part manufactured by GE to factory specifications — guaranteed fit and performance Quad (4-solenoid) valve assembly — independently controls hot water, cold water, bleach dispenser, and fabric softener dispenser ports Multi-colored ports for easy solenoid identification during installation Dimensions: approximately 7"L x 3"W x 3"H Current updated part number — directly supersedes WH13X24058 Compatible with GE GTW680, GTW685, GTW720, GTW725, GTW750, GTW755, PTW600, PTW605, PTW700, PTW705, GTN755 series top-load washers DIY repair — installs in 20–30 minutes with basic hand tools Product Specifications Part Number WH13X26637 Supersedes WH13X24058 Part Type Washer Water Inlet Valve Assembly (Quad / 4-Solenoid) Condition Genuine OEM Application GE and GE Profile Top-Load Washers Solenoids 4 (hot, cold, bleach, fabric softener) Dimensions Approximately 7"L x 3"W x 3"H Port Colors Multi-color (blue, green, red, tan, silver, gold) Material Plastic / Metal Compatible Brands GE, GE Profile Installation Notes ⚠️ Unplug Washer and Shut Off Water Before Starting Disconnect power and turn off both the hot and cold water supply valves before beginning. Pull the washer away from the wall to access the back panel and remove it to expose the valve assembly. Photograph all wire harness connections and hose routing — the multi-color ports make this straightforward. Disconnect the two external supply hoses from the hot and cold inlet ports. Disconnect the internal outlet hoses by releasing the retaining clips. Disconnect the wire harness connectors from each solenoid terminal. Unscrew the mounting bolts and remove the old valve. Install the new WH13X26637 valve in the same position, reconnect all hoses and wire harnesses in the documented positions, and secure the mounting bolts. Reconnect the external supply hoses, restore water supply and power, and run a fill cycle to verify normal filling and check for leaks. Tools needed: Phillips screwdriver, socket wrench, needle-nose pliers. Frequently Asked Questions What is the difference between WH13X26637 and WH13X24058? These are the same quad water inlet valve assembly — WH13X26637 is the current updated part number that GE issued to supersede the earlier WH13X24058. If your washer's documentation, parts diagram, or old valve label shows WH13X24058, the WH13X26637 is the correct current replacement to order. Both are quad (4-solenoid) valve assemblies with the same port configuration and function. What does each solenoid port on this quad valve control? The WH13X26637 quad valve has four independently operated solenoid ports. The hot water port opens to supply hot water from the household supply line. The cold water port supplies cold water. The bleach dispenser port delivers cold water through the bleach compartment at the appropriate point in the wash cycle. The fabric softener port delivers water through the softener compartment during the rinse cycle. When any single solenoid fails, only the function it controls is affected — the rest of the valve continues to work normally. My washer won't fill and shows an error code — is it the water inlet valve? A fill error code on compatible GE models commonly points to the water inlet valve. Before replacing the valve, confirm that both supply valves behind the washer are fully open, neither supply hose is kinked, and the household water pressure is adequate. You can test each solenoid coil with a multimeter — a working coil shows resistance (typically 200–500 ohms); an open circuit confirms that coil has failed and the valve needs replacement. If all coils test good but the washer still won't fill, the issue may be with the control board or water pressure. My washer fills fine but won't dispense fabric softener — could it be the valve? Yes — if only the fabric softener dispenser function is affected, the solenoid coil controlling that specific port has likely failed. Since it is part of the same quad valve assembly, replacing the entire WH13X26637 assembly resolves the failed port. Individual solenoid ports cannot be replaced — the complete quad valve assembly must be replaced when any port fails. Is this a Genuine OEM or aftermarket part? This is a Genuine OEM part manufactured by GE to factory specifications. It is the exact same quad water inlet valve assembly installed in compatible GE and GE Profile top-load washers from the factory — guaranteed fit, materials, and performance. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO EAU64082901 Washer Drain Pump Motor – for AHA75693425 – Compatible with LG & Kenmore Washers Product Description Restore proper draining and reliable washer operation with the XPARTCO EAU64082901 Washer Drain Pump Motor. This high-quality replacement pumps water out of the washer tub during drain and spin cycles. A failing drain pump motor can cause water not draining, standing water, slow spin cycles, or drain error codes. Replacing it with this dependable XPARTCO pump motor ensures efficient water removal and smooth washer performance. Replaces Part Numbers EAU64082901, PD00090792, AP6336279. EAP12750085. Replacement Motor for Drain pump Assembly for AHA75693425, PD00068706, EAP12750085, AP6978815, PS12750085 Compatibility This replacement washer drain pump motor fits select LG and Kenmore (LG-manufactured) front-load and top-load washers. Example compatible models include (but are not limited to):LG WM2277HW, WM2455HW, WM3470HWAKenmore 796.40272900, 796.41472210 Always verify your washer’s model number before ordering.Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement – Designed to match OEM flow rate and electrical performance 💧 Efficient Water Drainage – Removes water quickly during drain and spin cycles 🔇 Quiet Operation – Smooth motor design minimizes noise and vibration 💪 Durable Construction – Built for long service life in wet environments 🛡️ Fixes Common Issues – Solves washer not draining, water left in tub, or drain error codes 📐 Product Specification Part Number: EAU64082901 Component Type: Washer Drain Pump Motor only Voltage: 26V Mounting: Direct-fit pump housing installation Connection: Electrical terminals with hose ports Application: Drain and spin water removal Compliance: Built to OEM-equivalent quality standards (not OEM) 🛠️ Installation Notes Tools Needed: Phillips screwdriver, pliers, towel or shallow pan ⚠️ Safety First: Unplug the washer and turn off water supply before servicing. Steps: Disconnect power and water supply. Access the drain pump from the front or bottom panel. Place a towel to catch residual water. Disconnect hoses and wiring from the old pump motor. Install the new XPARTCO EAU64082901 pump motor. Reconnect hoses and wiring, reassemble panels, and restore power. Run a test drain cycle to confirm proper operation. ⏱️ Time Required: 20–30 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Appliance Parts Supplier 🔄 30-Day Return Policy Restore proper washer draining and avoid costly water issues — Add to Cart Now for a reliable, budget-friendly repair!

Read more less

DA62-00914B Genuine OEM Refrigerator Water Valve Fits Specific Samsung Refrigerator Models. Replaces Part Numbers:DA62-00914B, AP4142321, PS4146154. Description: This Water Valve is a Genuine OEM part for specific Samsung Refrigerator models. Refrigerator Water Inlet Valve is an essential component for maintaining the water supply in your Samsung refrigerator. This part ensures reliable performance and seamless integration with your appliance. Designed specifically for Samsung refrigerators, it guarantees a perfect fit and easy installation, allowing you to restore your fridge's water dispensing system efficiently. The Water Inlet Valve controls the flow of water into the refrigerator, preventing leaks and ensuring consistent water pressure for ice makers and water dispensers.  

Read more less

DC31-00181CCM Washer Circulation Pump 120V, 60Hz, 0.65A Re-circulation pump. Fits select Samsung front load washer models. Replaces Part Numbers: DC31-00181C, DC31-00030E, DC31-00030J, DC96-01113G, 4813796, DC31-30008F, AP6025315, PS11758869. Description: This Washer Motor AC Re-circulation Pump motor is an essential component for maintaining your washer's optimal performance. This replacement part ensures reliable operation by efficiently circulating water within the motor, preventing overheating and extending the lifespan of your appliance. Designed specifically for select Samsung washer models.   This is an aftermarket part that can be used as a replacement for the OEM part.

Read more less

XPARTCO W11130359 Washer Suspension Rod Kit – Compatible with Whirlpool, Maytag, Amana, Crosley, and Roper Washers Product Description Reduce vibration and restore smooth, stable operation with the XPARTCO W11130359 Washer Suspension Rod Kit. This high-quality aftermarket replacement supports the washer tub and absorbs movement during wash and spin cycles. Worn or broken suspension rods can cause loud banging noises, excessive shaking, or unbalanced loads. Replacing them with this reliable XPARTCO kit ensures balanced performance and extends the life of your washer. Replaces Part Numbers W11130359, W11027215, 4813873, W10594082, W10785954, W10821704, W10901060, W11033536, W11226784, AP6261901, PD00042502, EAP12347544, PS12347544. Compatibility This replacement suspension rod kit fits select Whirlpool, Maytag, Amana, Crosley, and Roper top-load washers. Example compatible models include (but are not limited to): Whirlpool WTW5000DW1, Maytag MVWC565FW0, and Amana NTW4516FW3. Always verify your washer’s model number before ordering. Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement – Built to match OEM performance and stability 🌀 Reduces Vibration – Keeps washer tub balanced during spin cycles 💰 Cost-Effective Solution – High-quality kit at a lower cost than OEM parts 🛠️ Complete Kit – Includes four suspension rods, bushings, and suspension springs 🛡️ Fixes Common Issues – Solves excessive shaking, banging, or unbalanced load problems 📐 Product Specification Part Number: W11130359 Component Type: Washer Suspension Rod Kit Includes: 4 suspension rods with springs and mounting bushings Material: Heavy-duty steel with corrosion-resistant coating Mounting: Direct-fit installation under washer tub Compliance: Built to OEM-equivalent quality standards (not OEM) 🛠️ Installation Notes Tools Needed: Phillips screwdriver, pliers, socket wrench ⚠️ Safety First: Always unplug the washer before performing repairs to prevent electrical shock or injury. Steps: Disconnect power and remove the washer lid or top panel. Support the washer tub with a sturdy object or strap. Remove the old suspension rods from their mounting holes. Install the new XPARTCO W11130359 rods one by one, attaching springs and bushings. Reassemble panels, plug in the washer, and run a test cycle to confirm smooth operation. ⏱️ Time Required: 30–40 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Appliance Parts Supplier 🔄 30-Day Return Policy Eliminate noise and vibration — Add to Cart Now for a stable, long-lasting repair!

Read more less

AJU34125552 Genuine OEM LG Refrigerator Water Inlet Valve The AJU34125552 is a genuine LG OEM water inlet valve for LG refrigerators, supplying water to both the ice maker and the door water dispenser from a single valve assembly. Mounted at the rear of the refrigerator where the household water supply line connects, this valve opens on command from the control board to admit water for either feature, and closes again once the request is satisfied. Common causes of failure include mineral and sediment buildup from hard water interfering with the internal solenoid over time, and general electrical wear. A failing valve typically shows up as the ice maker no longer producing ice, the water dispenser slowing down or stopping entirely, or both symptoms appearing together since one valve serves both functions. Quick Answer The AJU34125552 Genuine OEM LG Refrigerator Water Inlet Valve fixes LG refrigerators where the ice maker stopped making ice, the water dispenser isn't working, water flow is slow, or there's a leak near the valve at the back of the refrigerator. Supplies both the ice maker and dispenser from one valve. Common Problems This Part Fixes Ice maker has stopped making ice, or is producing less ice than usual Water dispenser on the refrigerator door isn't working or has slowed down Both the ice maker and water dispenser affected together Slow water flow at the dispenser Water leaking near the valve at the back of the refrigerator No water or ice production at all Valve failure following known hard water conditions at the home Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers AJU34125552, EAP10066440, FIX10066440, OEM17872815, PS10066440, AP5957602, ALG1274937, PD00053838. We were not able to confirm additional cross-reference or superseding part numbers for this specific part number from reliable sources at the time this page was built, so none are listed here rather than guessed. If you have a cross-reference number for your appliance, contact our support team and we will verify compatibility before you order. Compatibility This water inlet valve is compatible with select LG refrigerators. Note: A specific verified compatible model list was not available at the time this page was built. LG has used several visually similar water inlet valve part numbers across different refrigerator platforms, and parts that look identical can have small but important differences. Always verify your full model number before ordering. Contact our support team with your model number and we will confirm fitment before you purchase. Key Features Genuine LG OEM part — factory-specified solenoid design and flow-rate calibration Single valve assembly supplies water to both the ice maker and door water dispenser Resolves "ice maker not making ice," "dispenser not working," "slow water flow," and "leak near the valve" symptoms caused by valve failure Genuine OEM replacement — guaranteed fit, materials, and performance DIY-friendly repair — typically 15 to 30 minutes Product Specifications Part Number AJU34125552 Part Type Refrigerator Water Inlet Valve (Ice Maker + Dispenser) Condition Genuine OEM Brand LG Location Rear of refrigerator, at the household water line connection Function Supplies water to the ice maker and door water dispenser Repair Difficulty Easy — 15 to 30 minutes Quantity 1 valve assembly Compatible Brand LG Installation Notes ⚠️ Unplug Refrigerator Before Starting — Store Perishable Food Separately Shut off the water supply and unplug the refrigerator before beginning, and move perishable food to a cooler for the duration of the repair. Wear work gloves. Pull the refrigerator away from the wall for access, then locate the valve at the rear of the cabinet where the water supply line connects. Photograph the wiring harness and water line connections before disconnecting anything. On some installations, the wiring harness has been routed between water supply lines, which can make the connector difficult to reach and unplug — if this is the case, gently reposition or loosen a water line first rather than forcing the connector. Disconnect the water supply line from the old valve, disconnect the electrical connector, and remove the mounting screws holding the valve in place, then pull it free. Install the new AJU34125552 in the same position, secure the mounting screws, and reconnect the electrical connector fully — route the wiring the same way the original was routed, avoiding pinch points against the water lines if possible. Reattach the water supply line, tightening securely by hand plus a partial turn with pliers. Restore the water supply and check for leaks before restoring power. Push the refrigerator back into place and test both the ice maker and water dispenser over the following day to confirm normal operation. Tools needed: Phillips screwdriver, adjustable wrench or pliers, work gloves. Frequently Asked Questions My ice maker and dispenser both stopped working at the same time. Is that normal for a valve failure? Yes, this is actually a very telling symptom. Because one valve assembly supplies water to both the ice maker and the door dispenser, a failure inside the valve itself commonly affects both functions simultaneously. If only one of the two has stopped working while the other functions normally, it's worth double-checking the water filter and supply line for a localized restriction before assuming the valve has failed, but a simultaneous failure of both points strongly toward this valve. The wiring harness on my old valve was hard to reach. Is that normal? It can be, depending on how the original installation routed the wiring. Some installations run the harness between two water supply lines, which can make the connector awkward to access and unplug. If you find yourself in this situation, gently repositioning or loosening a nearby water line first — rather than forcing the connector — makes it much easier to disconnect without damaging anything. Could hard water be why my valve failed? Yes, this is a common and well-documented cause. Mineral deposits from hard water can build up inside the valve over time and interfere with the internal solenoid's ability to open and close properly, eventually leading to failure. If you know your home has hard water and this valve has failed, it may be worth considering a water softener or more frequent filter changes to extend the life of the replacement. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by LG to factory specifications — guaranteed fit, materials, and performance. It includes the same solenoid design and dual-function (ice maker and dispenser) configuration as the water inlet valve originally installed in your refrigerator. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

242253002 Refrigerator Genuine OEM Water Valve Replaces Part Numbers:242253002, 242102201, 2689640, OEM22679498, AP5669874, PS7321353. Description: This Water Inlet Valve is a Genuine OEM part for specific Frigidaire refrigerator models. It is designed to manage the flow of water to the ice maker and water dispenser. This solenoid-operated valve responds to commands from the refrigerator's electronic control, opening to allow water in and closing to stop the flow, ensuring proper operation of both ice production and water dispensing functions.   California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less