Search results for "hvac Switch"

WE11X203 Dryer Genuine OEM Heater Restring Coil Kit  Dryer heating element restring kit. This kit replaces the existing heating coil in your dryer.  This Heater restring Coil Replaces WE11X103 Heater Restring Coil.  The diameter of the coil is 1/2" OD it stretches around the pan over the ceramic insulators.   Replaces Part Numbers:WE11X203, AH265619, AP2620176, DE333, EA265619, K35-408, PS265619, WE11X0203, WE11X103C   California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

WR30X39385 Genuine OEM GE Refrigerator Ice Maker The WR30X39385 is a genuine GE OEM ice maker assembly for GE refrigerators. This complete unit receives water, holds it in an internal mold, and freezes it into cubes, then ejects the finished ice into the freezer's ice bucket or drawer, repeating the cycle automatically until the bucket is full. It's the full assembly, not just an internal component, so replacing it addresses the ice-making mechanism, mold, and cycling controls together as one unit. Over time, internal components can wear or fail electrically, or the mold itself can develop issues that affect how cleanly ice releases. A failing ice maker typically shows up as reduced or stopped ice production, or ice cubes coming out hollow or malformed rather than solid. It directly replaces AP7179920. Quick Answer The WR30X39385 Genuine OEM GE Refrigerator Ice Maker fixes GE refrigerators that have stopped making ice, are producing significantly less ice than usual, or are making hollow or malformed cubes. Complete ice maker assembly. Replaces AP7179920. Installation is a moderate DIY repair, typically 30-45 minutes. Common Problems This Part Fixes Ice maker has stopped producing ice entirely Ice maker producing significantly less ice than usual Ice cubes coming out hollow or malformed instead of solid Ice maker cycling but not ejecting cubes into the bucket Inconsistent ice production from cycle to cycle Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This refrigerator ice maker directly replaces the following OEM and cross-reference part numbers: WR30X39385, 200D1181G118, 4983508, Model CAN07-018, WR01F04991, AP7179920, EAP16660009, AGE28641, PD00079707, PS16660009 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This ice maker is compatible with select GE refrigerators, and also fits select Hotpoint, Haier, Monogram, and Café refrigerators built on the GE platform. Note: Always verify your full model number before ordering, since GE uses several different ice maker designs across its refrigerator lineup. Contact our support team with your model number if you're unsure. Key Features Genuine GE OEM part — factory-specified mold design and cycling mechanism Complete ice maker assembly — freezes water into cubes and ejects them automatically Resolves "not making ice," "reduced ice production," and "hollow or malformed cubes" symptoms Direct drop-in replacement — no modification required Replaces AP7179920 Compatible with GE, Hotpoint, Haier, Monogram, and Café refrigerators Genuine OEM replacement — guaranteed fit, materials, and performance Moderate DIY repair, typically 30-45 minutes Product Specifications Part Number WR30X39385 Part Type Refrigerator Ice Maker Assembly Condition Genuine OEM Brand GE Function Freezes water into cubes and ejects them automatically into the ice bucket/drawer Repair Difficulty Moderate — 30 to 45 minutes Quantity 1 ice maker assembly Compatible Brands GE, Hotpoint, Haier, Monogram, Café Installation Notes ⚠️ Unplug Refrigerator Before Starting — Allow Components To Defrost Disconnect power to the refrigerator before beginning, and move perishable food to a cooler for the duration of the repair. Wear work gloves. If there's frost or ice buildup around the ice maker or its fill tube, allow the area to defrost fully before continuing, since ice buildup can make removal difficult and may mask the fill tube's actual condition. Open the freezer door and locate the ice maker assembly. Remove the ice bucket or drawer to improve access. Photograph the wiring harness connection and the fill tube position before disconnecting anything. Remove the mounting screws securing the ice maker in place, then disconnect the wire harness connector and the water fill tube connection. Remove the old ice maker fully. Install the new WR30X39385 in the same mounting position, making sure the fill tube aligns correctly so water reaches the mold without leaking, and reconnect the wire harness connector securely. Secure the mounting screws, reinstall the ice bucket or drawer, and restore power. Allow several hours for the first cycle to complete and confirm ice is being produced and ejected normally. Tools needed: Phillips screwdriver, work gloves. Frequently Asked Questions My ice cubes are coming out hollow. Is that the ice maker? Yes, hollow or malformed cubes are a documented symptom of ice maker issues on this platform, alongside reduced or stopped ice production altogether. This can point to a problem with how the mold fills or releases ice, and replacing the complete assembly addresses the mold and cycling mechanism together rather than trying to diagnose and repair individual internal components. Why does the fill tube alignment matter so much during installation? The fill tube is what delivers water from the refrigerator's supply line into the ice maker's mold at the start of each cycle. If it's not aligned correctly during installation, water can miss the mold, leak into the freezer compartment, or fail to fill the mold completely, all of which prevent normal ice production even with a perfectly good new ice maker installed. Do I need to defrost anything before starting this repair? If there's visible frost or ice buildup around the old ice maker or its fill tube, yes — letting that area defrost fully makes removal easier and gives you a clearer look at the fill tube's actual condition, rather than working around ice that could mask damage or make the old unit harder to detach cleanly. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by GE to factory specifications — guaranteed fit, materials, and performance. It includes the same mold design, cycling mechanism, and mounting configuration as the ice maker originally installed in your refrigerator. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO EAU61524007 Refrigerator Evaporator Fan Motor 13V, 1.5 W, 0.118A. 1-1/2" shaft. Has quick disconnect. Fits specific LG Refrigerator Models. Description:  This ERP EAU61524007 Refrigerator Evaporator Fan Motor is designed for reliable and efficient cooling performance. It features the EAU61524007 model, providing optimal airflow and preserving freshness in your refrigerator. Upgrade your appliance with this high-quality fan motor and enjoy the benefits of improved cooling and longer-lasting food. Replaces Part Numbers:EAU61524007, AP5950081, EAU60694510, PS10058947   This is an aftermarket part that can be used as a replacement for the OEM part.

Read more less

XPARTCO 4681JB1029D Refrigerator Condenser Fan Motor – Compatible with LG and Kenmore Refrigerators Product Description Keep your refrigerator running efficiently with the XPARTCO 4681JB1029D Refrigerator Condenser Fan Motor. This Condenser Fan Motor is a replacement part for specific LG, Kenmore refrigerator models. This motor is responsible for powering the fan that cools the condenser coils, which helps dissipate heat from the refrigerator. Proper functioning of the condenser fan motor is crucial for maintaining the efficiency and cooling performance of the refrigerator. Replaces Part Numbers 4681JB1029D, EAU61644104, 4681JB1029Q, 1267566, AH3523330, EA3523330, PD00008709, AP4437783, PS3523330. Compatibility This replacement condenser fan motor fits select LG and Kenmore refrigerators. Example compatible models include (but are not limited to): LG LFX25974ST, LG LFX28968ST, and Kenmore 795.71053.010. Always verify your refrigerator’s model number before ordering. Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement – Designed to match OEM performance for LG refrigerators 🌬️ Reliable Airflow – Circulates air over coils to prevent overheating and improve efficiency 💰 Cost-Effective Fix – Quality replacement at a lower cost than OEM parts 🛠️ DIY Installation – Plug-and-play wiring connector for easy setup 🛡️ Fixes Common Issues – Solves overheating, loud operation, or poor cooling problems 📐 Product Specification Part Number: 4681JB1029D Component Type: Refrigerator Condenser Fan Motor Assembly Material: Metal motor housing with plastic fan blade Mounting: Direct-fit on rear compressor compartment bracket Operating Conditions: Designed for continuous operation in refrigerator environments Compliance: Built to OEM-equivalent quality standards (not OEM) 🛠️ Installation Notes Tools Needed: Phillips screwdriver, nut driver, pliers ⚠️ Safety First: Always unplug the refrigerator before performing any repairs to prevent electrical shock. Steps: Disconnect power and pull refrigerator away from wall. Remove the rear access panel to expose the condenser area. Disconnect wiring harness and remove the old fan motor. Mount the new 4681JB1029D motor using the same screws. Reconnect the wiring harness and reinstall the rear panel. Plug in the refrigerator and confirm proper fan operation. ⏱️ Time Required: 20–25 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Appliance Parts Supplier 🔄 30-Day Return Policy Keep your refrigerator cool and efficient — Add to Cart Now for a reliable, budget-friendly replacement!

Read more less

XPARTCO 2188820 Refrigerator Thermistor (Sensor) Replaces WP2188820 The XPARTCO 2188820 is an aftermarket replacement refrigerator temperature sensor (thermistor) compatible with select Whirlpool, Kenmore, KitchenAid, Maytag, Jenn-Air, Dacor, and Thermador refrigerators. The thermistor is an NTC (negative temperature coefficient) sensor that continuously monitors the air temperature inside the refrigerator or freezer compartment and sends resistance-based readings to the electronic control board. The control board uses these readings to regulate compressor run time and fan operation, maintaining the set temperature accurately and efficiently. This thermistor features an NTC resistance of 50K ohms at 25°C (27K ohms at 0°C/32°F) and a standard wire length of approximately 5.3 inches (13.46 cm), compatible with low-voltage refrigerator control boards (5V/12V). It directly replaces WP2188820, 2213442, AP6006068, PS11739132, and 1057764. Note: this thermistor is compatible with non-WISE system refrigerators only — it is not compatible with newer Whirlpool refrigerators using the WISE (Whirlpool Intelligent Smart Energy) control system. Installs in under 15 minutes. Quick Answer The XPARTCO 2188820 Refrigerator Thermistor fixes Whirlpool-family refrigerators that are too warm, too cold, have erratic temperatures, run the compressor too long, or display temperature-related error codes. NTC sensor, 50K ohm at 25°C, ~5.3" wire. Non-WISE system models only. Compatible with Whirlpool, Kenmore, KitchenAid, Maytag, Jenn-Air, Dacor, and Thermador. Replaces WP2188820, 2213442, AP6006068, PS11739132. Common Problems This Part Fixes Refrigerator not maintaining set temperature — too warm or too cold Freezer section too warm or food not freezing properly Compressor running continuously without cycling off Temperature fluctuating erratically despite stable ambient conditions Refrigerator temperature-related error codes displayed on the control panel Excessive frost buildup caused by incorrect temperature regulation Food or beverages freezing in the fresh food section Replaces Part Numbers This refrigerator thermistor directly replaces the following OEM and cross-reference part numbers: WP2188820, 2188820, 2213442, EAP11739132, AWP46934, PD00033406, AP6006068, PS11739132. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This thermistor is compatible with select refrigerators from the following brands and series: Whirlpool refrigerators — 5VW, GC3, EC3, GC5 series Kenmore / Sears refrigerators — 106 series (Whirlpool-built models) KitchenAid refrigerators — KSCS, KSSS, JS series Maytag refrigerators (select models) Jenn-Air refrigerators (select models) Dacor refrigerators (select models) Thermador refrigerators (select models) Important — WISE System Compatibility: The 2188820 thermistor is compatible with non-WISE system refrigerators only. It is not compatible with newer Whirlpool refrigerators equipped with the WISE (Whirlpool Intelligent Smart Energy) control system. If your refrigerator uses the WISE system, this thermistor will not work correctly. Verify your model number before ordering, or contact our support team to confirm compatibility. Key Features NTC (negative temperature coefficient) thermistor — resistance decreases as temperature increases, allowing precise temperature monitoring 50K ohm resistance at 25°C (27K ohm at 0°C/32°F) — matches original WP2188820 specifications Wire length approximately 5.3 inches (13.46 cm) — standard length matching OEM dimensions Low-voltage design compatible with 5V/12V refrigerator control boards Continuously sends temperature readings to the control board to regulate compressor and fan operation Non-WISE system compatible only — verify your model before ordering Direct replacement for WP2188820, 2213442, AP6006068, and PS11739132 Compatible with Whirlpool, Kenmore, KitchenAid, Maytag, Jenn-Air, Dacor, and Thermador refrigerators Aftermarket replacement built to OEM-equivalent quality standards Quick DIY repair — installs in under 15 minutes Product Specifications Part Number 2188820 OEM Part Number WP2188820 Part Type Refrigerator Temperature Sensor (NTC Thermistor) Condition Aftermarket Replacement Sensor Type NTC (Negative Temperature Coefficient) Resistance at 25°C 50,000 ohms (50K ohm) Resistance at 0°C (32°F) 27,000 ohms (27K ohm) Wire Length Approximately 5.3 inches (13.46 cm) Voltage 5V / 12V (low voltage) WISE System Compatibility Non-WISE models only Compatible Brands Whirlpool, Kenmore, KitchenAid, Maytag, Jenn-Air, Dacor, Thermador Installation Notes ⚠️ Unplug Refrigerator Before Starting Disconnect power before beginning. The thermistor location varies by model — it is typically clipped to a bracket on the interior side wall of the fresh food or freezer compartment, or mounted near the evaporator coil. Consult your model's parts diagram or service manual to confirm the exact location before disassembly. Open the sensor cover or unclip the sensor bracket, disconnect the wiring connector, and pull the old thermistor out. Insert the new 2188820 thermistor, reconnect the wiring connector, and snap the cover or bracket back into place. Ensure the sensor head is positioned close to the compartment wall and the wiring is not pinched. Restore power and monitor the refrigerator temperature over the next few hours to confirm stable, accurate cooling. Tools needed: Phillips screwdriver (for panel access on some models); no tools needed for sensor replacement itself. Frequently Asked Questions What is the difference between 2188820 and WP2188820? These are the same thermistor. WP2188820 is the updated Whirlpool OEM part number that superseded the original 2188820. The 2213442 is also a cross-reference for the same part. This aftermarket replacement is compatible with all three numbers. What does an NTC thermistor do and how do I know if mine has failed? An NTC thermistor is a resistor whose resistance decreases as temperature increases. The control board sends a small voltage through the thermistor and measures the resulting resistance — a lower resistance means warmer temperature, and a higher resistance means cooler temperature. The board uses this reading to decide when to run the compressor and fans. A failed thermistor either reads open circuit (no continuity), short circuit (zero resistance), or provides incorrect readings that cause the refrigerator to run too warm, too cold, or cycle erratically. Test with a multimeter at room temperature — a working 2188820 should read approximately 50K ohms at 25°C (77°F). Significant deviation indicates failure. How do I know if my refrigerator uses the WISE system? The WISE (Whirlpool Intelligent Smart Energy) system was introduced on newer Whirlpool refrigerator models and uses a different thermistor specification that is not interchangeable with the 2188820. Models that use the WISE system are typically marked in the product documentation or on the control board. The easiest way to confirm compatibility is to verify your model number with our support team before ordering, or check whether WP2188820 appears in your model's official parts diagram. If your parts diagram lists WP2188820, this replacement is compatible. Where is the thermistor located in my refrigerator? The thermistor location varies by model and brand. On Whirlpool and KitchenAid models, it is commonly found on the interior side wall of the fresh food compartment clipped to a plastic housing. On some models it is located near the evaporator coil behind the freezer back panel. On Kenmore 106 series models, it may be on the fresh food section wall or inside the back panel. Consult your specific model's parts diagram or search for a model-specific installation video to locate the sensor before disassembling the refrigerator. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured with an NTC thermistor rated to the same 50K ohm specification as the original WP2188820 to match the performance and accuracy of the factory sensor. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

DA32-10105RCM Refrigerator Temperature Sensor  Replaces Part Numbers: DA32-10105R, DA32-00006W, DA32-00006U, 2030342, DA32-00006B, DA32-00006C, DA32-00006D, DA32-00006L, DA32-00006M, DA32-00006T, DA32-00006V, AP4135567, PS4138681. 1" probe, 25.75" lead with two pin connectors. Fits Specific Samsung Refrigerator Models. This Defrost Sensor is a replacement part designed specific Samsung refrigerator models. This sensor, sometimes referred to as a defrost thermostat or defrost temperature sensor, is an integral part of your refrigerator's defrost system.   This is an aftermarket part that can be used as a replacement for the OEM part. 

Read more less

XP61005518 Refrigerator Relay Fits Specific refrigerator Models Replaces Part Numbers: 12002782, 1194680, 61005518, AH2004057, EA2004057, OEM12028982, AP4009659, PS2004057. Description: This is a Replacement compressor overload and relay kit for Specific Whirlpool, Maytag, Kenmore Refrigerator models. Kit was recently redesigned by manufacturer.   This is an aftermarket part that can be used as a replacement for the OEM part. California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

6500JB1008A Refrigerator Genuine OEM Temperature Sensor Replaces Part Numbers: 6500JB1008A, 1395582, AH3529164, EA3529164, AP4440683, PS3529164.   California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

5303917633 Refrigerator Genuine OEM Defrost Timer Description: This Electrolux Defrost Timer is an OEM replacement part for specific Frigidaire refrigerators. The defrost timer regulates the automatic defrost cycle, which prevents ice buildup on the evaporator coils in the freezer compartment by sending a signal to the defrost heater to turn on and melt any ice buildup on the coils. Once the defrost cycle is complete, the timer signals the heater to turn off, allowing the coils to cool and return to their normal temperature. Replaces Part Numbers:5303917633, 3286, A769, AH468976, CC351, CC901, EA468976, AP2592955, PS468976. California Residents only WARNING: California’s Proposition 65 

Read more less

Genuine Refrigerator Installation Part WX08X10015 Refrigerator Genuine SmartConnect Water Supply Line (15 Feet) Genuine 15-foot SmartConnect water supply line for compatible refrigerators and icemaker connections. Product Overview The WX08X10015 Refrigerator SmartConnect Water Supply Line is a genuine 15-foot refrigerator water line designed for compatible refrigerator and icemaker installations. It connects the household water supply to the refrigerator water inlet system. Use this line for a new installation or to replace a leaking, kinked, damaged, or deteriorated refrigerator water supply line. Quick Answer WX08X10015 is a genuine 15-foot refrigerator SmartConnect water supply line for compatible refrigerator and icemaker installations. Common Problems This Part May Fix Leaking refrigerator water supply line Kinked or restricted water tubing Damaged or deteriorated supply line Insufficient line length for refrigerator placement Water line replacement during refrigerator installation Replaces and Cross-References WX08X10015, 880515, AGE1244675, AP3140389, EAP311504, PD00065821, PS311504, TJ915PEX, IMKR15 Part number is provided for identification. This listing is for a genuine replacement and installation part. Compatibility Designed for compatible refrigerators and icemaker installations requiring SmartConnect water supply line part number WX08X10015. Important: Verify the refrigerator installation requirements, connection type, available space, and required line length before ordering. Key Features Genuine replacement and installation part 15-foot refrigerator water supply line Designed for compatible refrigerator and icemaker hookups Provides additional installation length for flexible placement Direct replacement for applications calling for WX08X10015 Product Specifications Part Number WX08X10015 Part Type Refrigerator Water Supply Line Product Line SmartConnect Length 15 Feet Application Compatible Refrigerators / Icemakers Condition New Part Quality Genuine Replacement Part Package Quantity 1 Water Supply Line Installation & Troubleshooting Notes Shut off the household water supply before installation. Disconnect refrigerator power if access to electrical components is required. Inspect the existing connection points for corrosion, damage, or leaks. Route the new supply line without sharp bends, pinching, or kinks. Secure the line to the household supply and refrigerator inlet according to the appliance installation instructions. Restore the water supply slowly and inspect all connections carefully for leaks. Installation tip: Leave enough slack behind the refrigerator so the appliance can be moved for service without pulling or stressing the water line. Frequently Asked Questions How long is WX08X10015? This SmartConnect water supply line is 15 feet long. What is WX08X10015 used for? It connects a compatible refrigerator or icemaker water inlet system to the household water supply. Is WX08X10015 a genuine part? Yes. This listing is for a genuine refrigerator water supply line. Will this work with every refrigerator? No. Verify the refrigerator installation requirements and connection specifications before ordering. Shop With Confidence Verify your refrigerator installation requirements before purchasing. Our compatibility team can help confirm whether WX08X10015 is suitable for your application. Genuine Replacement15-Foot Water LineInstallation SupportFast U.S. Shipping

Read more less

XPARTCO WR60X10358 Refrigerator Condenser Fan Motor The XPARTCO WR60X10358 is an aftermarket replacement condenser fan motor, made to replace GE part WR60X10358, for select GE bottom-mount refrigerators. The motor runs the fan that blows air across the condenser coils, pulling heat away so the refrigerator does not overheat and keeps a consistent temperature. It sits in the machine compartment. This is an aftermarket replacement from XPARTCO, not a genuine GE part. It is sold individually. Check your model number before ordering. Quick Answer The XPARTCO WR60X10358 Condenser Fan Motor replaces the condenser fan motor on a compatible GE bottom-mount refrigerator when it has failed. Replaces WR60X10339. Common signs of a failing condenser fan motor: the fan is noisy or not turning, or the refrigerator runs warm. When To Replace This Part Condenser fan is noisy Condenser fan is not turning Refrigerator or freezer is running warm because the condenser is not being cooled Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This condenser fan motor is made to replace the following GE part numbers: WR60X10358, WR60X10339, 3033263, D1225X14BXCPB47, AGE29414, AP5781519, EAP8690738, PD00024607, PS8690738 If your old motor shows a different number, contact our support team and we'll check whether it matches. Compatibility This condenser fan motor is listed for GE bottom-mount refrigerators, including these examples: GE GNE26GMDDES, GNE26GGDAWW, GNE26GSDASS, GNE26GMDAES GE GFE29HGDEWW, GFE29HGDCWW, GFE29HMDDES GE DFE29JGDAWW, DFE29JMDAES, DFE29JSDESS GE PFE27KSDDSS, PYE23KSDASS, PYE23PSDASS, CYE23TSDASS Note: The models above are a sample, not a full list. GE sells many condenser fan motors with different part numbers that look alike. Check your full model number against your parts diagram, or contact our support team to verify fit before ordering. Key Features Aftermarket replacement for the GE WR60X10358 condenser fan motor Moves air across the condenser coils to keep the refrigerator cooling efficiently Cross-references GE WR60X10339 Sold individually Product Specifications Part Number XPWR60X10358 OEM Part Number WR60X10358 Part Type Refrigerator Condenser Fan Motor Condition Aftermarket Replacement Quantity 1 Motor Application Select GE Bottom-Mount Refrigerators Installation Notes ⚠️ Disconnect Power Before Installing Unplug the refrigerator, move any food that could spoil, and wear work gloves. Remove the rear access panel to the machine compartment, note how the wiring connects, and disconnect the motor. Remove the old motor and fan blade, install the new motor, reconnect the wiring, and refit the panel. Restore power and check that the fan runs. Frequently Asked Questions My refrigerator is warm or noisy. Is this the part I need? It can be. Check the condenser coils for dust and make sure nothing is blocking the fan first. If the fan does not spin freely or the motor is noisy, replace the motor. Is this an OEM or aftermarket part? This is an aftermarket replacement from XPARTCO, made to replace GE part WR60X10358. If you specifically need a genuine GE part, contact our support team. Does this replace WR60X10339? Yes. WR60X10339 is an earlier GE number for this condenser fan motor, and this motor is made to replace both. If your motor shows another number, contact our support team and we'll check it. Will this fit my refrigerator? It is listed for select GE bottom-mount models, but the model list above is only a sample. Check your full model number against your parts diagram, or contact our support team and we'll verify it before you order. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

17438000001373 Washer Genuine OEM Water Level Sensor Assembly – Compatible with Midea, Insignia Washers Product Description Restore accurate water level detection and optimal washing performance with the 17438000001373 Washer Genuine OEM Water Level Sensor Assembly. This factory-original OEM sensor monitors water levels inside the washer and communicates with the control board to regulate fill cycles and ensure proper operation. A faulty sensor can lead to overfilling, underfilling, or cycles not completing correctly. Replacing it with this Genuine OEM assembly ensures precise sensing, proper communication with the control system, and long-lasting reliability. This part is manufactured to original factory specifications for dependable washer performance. Replaces Part Numbers 17438000001373, 302421600037, PS18188481 (verify if needed) Compatibility This Genuine OEM washer water level sensor assembly fits select Midea, Insignia washers. Common compatible models include (but are not limited to): Midea MAD160S2801GPSFMUS13, MLV41N1AWW, MAD160S2801PS, CTW41N1AW, MLV41N1AWWC, CLAWI47W, ATLMW41, CTW45N1AW, CTW45N2AW, CTW45N2AW, CTW45N1AW Always verify your washer’s model number before ordering.Contact our support team if you’re unsure. ✅ Key Features 🏭 Genuine OEM Part – Manufactured to original factory specifications 💧 Accurate Water Level Detection – Ensures proper fill and cycle control ⚙️ Fixes Common Issues – Resolves overfill, underfill, and sensor errors 🧩 Complete Sensor Assembly – Ready for direct installation 💪 Reliable Performance – Designed for long-term durability ⚠️ Symptoms If your washer is experiencing any of the following issues, this part may need replacement: 💧 Washer overfilling or underfilling ⚠️ Incorrect water levels during cycles 🔄 Cycle not completing properly 🛑 Washer stopping mid-cycle 🚫 Continuous filling or no fill condition Replacing this sensor assembly can restore proper water level control and washer operation. 📐 Product Specification Part Number: 17438000001373 Component Type: Washer Water Level Sensor Assembly Function: Detects water level and communicates with control board Connection Type: Electrical connector + pressure sensing system Application: Washer fill and cycle control system OEM Status: Genuine OEM 🛠️ Installation Notes Tools Needed: Phillips screwdriver ⚠️ Safety First: Unplug the washer before servicing to avoid electrical shock. Basic Steps: Disconnect washer power. Access the control panel or top panel. Locate the water level sensor assembly. Disconnect wiring and any attached pressure hose. Remove mounting screws and remove the old sensor. Install the new 17438000001373 Genuine OEM sensor. Reconnect wiring, reassemble, and restore power. Run a test cycle to confirm proper operation. ⏱️ Time Required: 20–30 minutes 📦 Shop With Confidence 🏭 Genuine OEM Appliance Part 🚚 Free Shipping on All Orders 🔄 30-Day Return Policy Restore factory-level washer performance and accurate water control — Add to Cart Now with confidence!

Read more less