Search results for "washer switch"

W10876600 Washer Genuine OEM Drain Pump – Compatible with Whirlpool, Maytag, Amana, and Crosley Washers Product Description Quickly and efficiently remove water from your washer with the W10876600 Washer Genuine OEM Drain Pump. This factory-approved replacement pump removes water from the tub during wash and spin cycles, ensuring smooth performance and proper draining. A faulty drain pump can cause standing water, error codes, or incomplete cycles. Replacing it with this Genuine OEM part restores dependable drainage and long-lasting washer performance. Replaces Part Numbers W10876600, 4455877, W10727777, W10876600VP, PD00034529, EAP11738156, AP6004933, PS11738156. Compatibility This Genuine OEM drain pump fits select Whirlpool, Maytag, Amana, and Crosley top-load and front-load washers. Example compatible models include (but are not limited to): Whirlpool WTW5000DW1, Maytag MVWC465HW0, and Amana NTW4516FW3. Always verify your washer’s model number before ordering. Contact our support team if you’re unsure. ✅ Key Features 🔄 Genuine OEM Replacement – Factory-approved for perfect fit and reliable operation 💧 Efficient Water Removal – Quickly drains water from the washer tub after each cycle 💪 Durable Motor Design – Built to withstand repeated use and heavy loads 🛠️ DIY Installation – Direct-fit replacement installs easily with basic tools 🛡️ Fixes Common Issues – Solves washer not draining, standing water, or “F9E1”/“SD” error codes 📐 Product Specification Part Number: W10876600 Component Type: Washer Drain Pump Assembly Material: Heavy-duty plastic pump housing and electric motor Voltage: 120V AC Mounting: Direct-fit on washer base with wiring harness connection Compliance: Genuine OEM certified 🛠️ Installation Notes Tools Needed: Nut driver, pliers, towel or bucket ⚠️ Safety First: Always unplug the washer and disconnect water supply before performing repairs to prevent electrical shock or leaks. Steps: Disconnect power and water hoses. Tilt the washer back or remove the front access panel. Unplug the wiring harness and loosen the clamps on the drain hoses. Remove the old pump and install the new W10876600 pump. Reconnect hoses and wiring, secure the pump, and restore power. Run a rinse or drain cycle to verify proper operation. ⏱️ Time Required: 20–30 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Genuine OEM Replacement Part 🔄 30-Day Return Policy Fix washer drainage issues fast — Add to Cart Now for a factory-quality repair that lasts!

Read more less

WH13X26637 Genuine OEM GE Washer Water Inlet Valve The WH13X26637 is a Genuine OEM GE replacement quad water inlet valve assembly compatible with select GE and GE Profile top-load washers in the GTW, GTV, GTN, PTW, and related series. This is a quad (4-solenoid) valve assembly that controls the flow of hot water, cold water, bleach dispenser water, and fabric softener dispenser water from the household supply lines into the washer tub and dispenser compartments. Each solenoid port is independently controlled by the washer's control board. When any port fails, the washer may not fill, fill too slowly, fill with the wrong temperature, overfill, fail to dispense bleach or fabric softener, or drip water between cycles. As a Genuine OEM part manufactured by GE to factory specifications, the WH13X26637 is a direct current-production replacement for the earlier WH13X24058. It measures approximately 7"L x 3"W x 3"H with multi-colored ports (blue, green, red, tan, silver, and gold) for easy identification of each solenoid's function. It directly replaces WH13X24058, WH13X26637-25PK, 4546358, AP6282070, EAP12171559, PD00037665, and PS12171559. Installs in 20–30 minutes with basic hand tools. Quick Answer The WH13X26637 Genuine OEM GE Washer Water Inlet Valve fixes GE top-load washers that won't fill, fill slowly, fill with wrong temperature, won't dispense bleach or fabric softener, overfill, or drip water between cycles. Quad (4-solenoid) valve. Approx. 7"L x 3"W x 3"H. Multi-color port identification. Genuine OEM. Replaces WH13X24058, WH13X26637-25PK, 4546358, AP6282070, EAP12171559, PS12171559. Compatible with GE GTW, GTV, GTN, PTW series top-load washers. Common Problems This Part Fixes Washer not filling with water at all when a cycle is started Washer filling very slowly — one or more solenoid ports partially blocked or failing Washer filling with only cold or only hot water — one temperature solenoid has failed Washer overfilling or filling continuously — valve port stuck open Bleach not dispensing during the wash cycle Fabric softener not dispensing at the rinse cycle point Water dripping into the tub between cycles — valve port not sealing completely Water leaking from the back of the washer near the valve body Replaces Part Numbers This water inlet valve directly replaces the following OEM and cross-reference part numbers: WH13X26637, WH13X24058, AGE26282, AP6282070, EAP12171559, PD00037665, PS12171559. WH13X26637 is the current updated part number superseding WH13X24058. If your washer's parts diagram shows WH13X24058, the WH13X26637 is the correct current replacement. Contact our support team with your model number if you need confirmation before ordering. Compatibility This water inlet valve is compatible with select GE and GE Profile top-load washers from the following series: GE washers — GTW680 series (GTW680BPL0DG, GTW680BPL1DG, GTW680BPL2DG, GTW680BSJ0WS, GTW680BSJ1WS, GTW680BSJ3WS, GTW680BSJ4WS, GTW680BSJ5WS, GTW680BSJ6WS and related models) GE washers — GTW685 series (GTW685BPL0DG, GTW685BPL1DG, GTW685BSL1WS, GTV685BSL0WS and related models) GE washers — GTW720 series (GTW720BPN0DG, GTW720BSN0WS and related models) GE washers — GTW725 series (GTW725BPN0DG, GTW725BSN0WS and related models) GE washers — GTW750 series (GTW750CPL0DG, GTW750CPL1DG, GTW750CSL0DG, GTW750CSL0WS, GTW750CSL1WS and related models) GE washers — GTW755 series (GTW755CPM0DG, GTW755CSM0WS, GTW755CSM1WS and related models) GE Profile washers — PTW600, PTW605, PTW700, PTW705 series and related models GE washers — GTN755 series (GTN755CPM1DG and related models) Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Genuine OEM part manufactured by GE to factory specifications — guaranteed fit and performance Quad (4-solenoid) valve assembly — independently controls hot water, cold water, bleach dispenser, and fabric softener dispenser ports Multi-colored ports for easy solenoid identification during installation Dimensions: approximately 7"L x 3"W x 3"H Current updated part number — directly supersedes WH13X24058 Compatible with GE GTW680, GTW685, GTW720, GTW725, GTW750, GTW755, PTW600, PTW605, PTW700, PTW705, GTN755 series top-load washers DIY repair — installs in 20–30 minutes with basic hand tools Product Specifications Part Number WH13X26637 Supersedes WH13X24058 Part Type Washer Water Inlet Valve Assembly (Quad / 4-Solenoid) Condition Genuine OEM Application GE and GE Profile Top-Load Washers Solenoids 4 (hot, cold, bleach, fabric softener) Dimensions Approximately 7"L x 3"W x 3"H Port Colors Multi-color (blue, green, red, tan, silver, gold) Material Plastic / Metal Compatible Brands GE, GE Profile Installation Notes ⚠️ Unplug Washer and Shut Off Water Before Starting Disconnect power and turn off both the hot and cold water supply valves before beginning. Pull the washer away from the wall to access the back panel and remove it to expose the valve assembly. Photograph all wire harness connections and hose routing — the multi-color ports make this straightforward. Disconnect the two external supply hoses from the hot and cold inlet ports. Disconnect the internal outlet hoses by releasing the retaining clips. Disconnect the wire harness connectors from each solenoid terminal. Unscrew the mounting bolts and remove the old valve. Install the new WH13X26637 valve in the same position, reconnect all hoses and wire harnesses in the documented positions, and secure the mounting bolts. Reconnect the external supply hoses, restore water supply and power, and run a fill cycle to verify normal filling and check for leaks. Tools needed: Phillips screwdriver, socket wrench, needle-nose pliers. Frequently Asked Questions What is the difference between WH13X26637 and WH13X24058? These are the same quad water inlet valve assembly — WH13X26637 is the current updated part number that GE issued to supersede the earlier WH13X24058. If your washer's documentation, parts diagram, or old valve label shows WH13X24058, the WH13X26637 is the correct current replacement to order. Both are quad (4-solenoid) valve assemblies with the same port configuration and function. What does each solenoid port on this quad valve control? The WH13X26637 quad valve has four independently operated solenoid ports. The hot water port opens to supply hot water from the household supply line. The cold water port supplies cold water. The bleach dispenser port delivers cold water through the bleach compartment at the appropriate point in the wash cycle. The fabric softener port delivers water through the softener compartment during the rinse cycle. When any single solenoid fails, only the function it controls is affected — the rest of the valve continues to work normally. My washer won't fill and shows an error code — is it the water inlet valve? A fill error code on compatible GE models commonly points to the water inlet valve. Before replacing the valve, confirm that both supply valves behind the washer are fully open, neither supply hose is kinked, and the household water pressure is adequate. You can test each solenoid coil with a multimeter — a working coil shows resistance (typically 200–500 ohms); an open circuit confirms that coil has failed and the valve needs replacement. If all coils test good but the washer still won't fill, the issue may be with the control board or water pressure. My washer fills fine but won't dispense fabric softener — could it be the valve? Yes — if only the fabric softener dispenser function is affected, the solenoid coil controlling that specific port has likely failed. Since it is part of the same quad valve assembly, replacing the entire WH13X26637 assembly resolves the failed port. Individual solenoid ports cannot be replaced — the complete quad valve assembly must be replaced when any port fails. Is this a Genuine OEM or aftermarket part? This is a Genuine OEM part manufactured by GE to factory specifications. It is the exact same quad water inlet valve assembly installed in compatible GE and GE Profile top-load washers from the factory — guaranteed fit, materials, and performance. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

W11305308 Dishwasher Genuine Whirlpool Control Board Control Board  Main electronic control board. Fits Specific Whirlpool Dishwasher Models. Replaces Part Numbers:W11305308, W11131683, W10918994, W11170192, W11227807, AP6832578, PS12704681.

Read more less

Genuine OEM WH23X10043 Washer Drain Pump The WH23X10043 is a genuine OEM drain pump from GE for GE and Hotpoint washers. The drain pump pushes wash water out of the tub and through the drain hose during the drain portion of the cycle. When it clogs, wears out, or leaks, the washer may leave water in the drum, stop before the spin, throw drain-related problems, leak from the pump, or make unusual noise while draining. This is a genuine OEM part, not an aftermarket equivalent, so the fit and operation match the original pump. It is a straightforward repair for most owners, usually under an hour, with a nutdriver, pliers and screwdrivers. Quick Answer The Genuine OEM WH23X10043 Drain Pump fixes a GE or Hotpoint washer that won't drain, leaves water in the drum, drains slowly, leaks from the pump, or makes noise while draining because the pump has failed. Genuine OEM from GE Appliances. Classic symptom: the cycle stalls with water still in the tub, or you hear the pump hum or grind but the water doesn't leave. Common Problems This Part Fixes Washer won't drain, or water is left in the drum after the cycle Slow or incomplete draining Water leaking from the pump Unusual noise while the washer drains Cycle stopping before the spin because the water hasn't drained Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This drain pump is listed under the following part number: WH23X10043, 2754597, DP035-043, AGE26084, AP5632594, EAP3654194, PD00023322, PS3654194 We have not found any superseded or alternate manufacturer numbers for this pump. If your old pump or parts diagram shows a different number, contact our support team and we'll check whether it matches. Compatibility This drain pump is listed for washers from: GE, including GBAN2800F0WW, GCWN4950D0WS, GHWN4250D0WW, GLWN5550D0WW, GMAN4250F0WS, and GTWN5650F2WS Hotpoint, including HTAP1200D1WW and MTAP1200D0WW Note: The model list above is only a sample, since retailers list 100 or more compatible models. Confirm fit by matching the number on your old pump or your parts diagram, or contact our support team with your model number and we'll verify before you order. Key Features Genuine OEM GE washer drain pump, not an aftermarket equivalent Restores full draining so cycles finish and the washer can spin Fits a wide range of GE and Hotpoint washers Simple replacement, typically under an hour with basic hand tools Product Specifications Part Number WH23X10043 OEM Part Number WH23X10043 Part Type Washer Drain Pump Condition Genuine OEM Manufacturer GE Appliances Approx. Size About 9 in H x 6 in L x 4 in Thick Application Select GE & Hotpoint Washers Installation Notes ⚠️ Unplug Power and Expect Water Unplug the washer and turn off the water supply before starting. Work gloves are recommended. Put towels and a shallow pan under the work area, since some water will remain in the pump and hoses. Following your model's service guide, remove the panel needed to reach the pump, disconnect its wiring connector, and loosen the clamps holding the hoses. Pull the hoses off, remove the pump's mounting fasteners, and take out the old pump. Install the new pump in the same position, reattach the hoses with their clamps (replace worn clamps if needed), and reconnect the wiring. Replace the panel, restore power and water, and run a drain cycle while checking for leaks. Reviewers note the hose clamps can be difficult, so have pliers ready. Frequently Asked Questions My washer won't drain. Is this the part I need? A failed or clogged drain pump is a common cause. Before replacing it, check the drain hose and the pump for a clog from a sock, coin, or lint. If the path is clear but the pump hums, grinds, leaks, or doesn't run, replacing it should fix the problem. Will this fit my GE or Hotpoint washer? It is listed for a wide range of GE and Hotpoint washers. Match the number on your old pump or parts diagram, or contact our support team with your model number and we'll confirm fit before you order. Do I need special tools? No. A nutdriver, pliers, and screwdrivers are typically all you need. Pliers help with the hose clamps. Is this a genuine GE part? Yes. This is a genuine OEM part from GE Appliances, not an aftermarket equivalent. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Genuine OEM Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

5220FR2006H Washer Hot Water Inlet Valve - Compatible with LG, Kenmore Product Description Ensure proper water flow with the replacement 5220FR2006H Washer Hot Water Inlet Valve. This replacement water inlet valve is designed for select LG and Kenmore front-load and top-load washers, featuring one solenoid to control hot water entry into the drum. It addresses issues like no water flow, leaks, improper filling, or error codes, offering a cost-effective alternative to OEM parts. Note: Includes one water inlet valve with one solenoid. Disconnect power and water supply before installation. Check water supply lines and valve filters for blockages to ensure optimal performance. Replaces part numbers: 5220FR2006H, 1268123, 5220FR1280F, 5220FR2006L, 5220FR2006Q, AH3527427, EA3527427, PD00001765, EAP3527427, AP4441935, PS3527427. Compatibility: Compatible with models including but not limited to: LG: WM2016CW, WM2077CW, WM2277HW, WM2455HW, WM2487HRM, WM2601HW, WM2701HV, WM2801HWA, WM3070HWA, WM3470HWA, WM8000HVA, WM9000HVA Kenmore: 796.40272800, 796.41022900, 796.41028900 Verify your model number or contact our support team for assistance. Key Features: ✅ Brand and Models Compatibility: Fits select LG and Kenmore front-load and top-load washers. 💧 Specifications: replacement water inlet valve with one solenoid, 120V, 60Hz. 💰 Cost-Effective Alternative: Offers OEM-equivalent performance at a lower price. 🛠️ Easy Installation: Requires screwdriver, pliers, work gloves; typically installed in 20–30 minutes. 🛡️ Effective Fixes: Resolves no water flow, leaks, improper filling, or error codes. Product Specification Part Number: 5220FR2006H Component Type: Washer hot water inlet valve Material: High-grade plastic and metal Electrical Specs: 120V, 60Hz, one solenoid. Mounting: Screw-mounted near washer water inlet Operating Conditions: Suitable for high-pressure water supply environments Compliance: Prop 65 warning for California Installation Notes: Safety First: Disconnect the washer from the power source and water supply before installation. Shop for high-quality replacement appliance parts with a 30-day return policy. Keep your washer running smoothly today! Add to cart now for a budget-friendly fix!

Read more less

XPARTCO AJU75152601 Washer Water Inlet Valve Replaces 5221EA1008F, AJU73213301 The XPARTCO AJU75152601 is an aftermarket replacement washer water inlet valve assembly compatible with select LG and Kenmore top-load washers in the WT1, WT4, WT5, WT6, and WT7 series. This is a multi-port valve assembly that controls water flow from the household supply lines into the washer tub and dispenser compartments. The assembly contains multiple solenoid-operated valve ports: hot water inlet, cold water inlet, bleach dispenser valve, fabric softener dispenser valve, and jet spray valve — all integrated into a single assembly that connects to the washer's control board via wiring harnesses. When the water inlet valve fails — or when one individual port fails — the washer may not fill at all, fill too slowly, fill with the wrong temperature, overfill, fail to dispense bleach or fabric softener, or leak from the valve body. The valve solenoids operate at 12V DC. This kit includes the complete valve assembly and two AGM73269501 inlet screens. It directly replaces AJU73213301, 5221EA1008F, 5221EA1008P, AGF76283896, AP6308239, TAW35618287, AH3527446, AJU75152603, EA3527446, PS3527446, and PS12374721. Installs in 15–25 minutes with basic hand tools. Quick Answer The XPARTCO AJU75152601 Washer Water Inlet Valve fixes LG and Kenmore top-load washers that won't fill, fill slowly, fill with wrong temperature, won't dispense bleach or fabric softener, overfill, or leak from the valve. Multi-port assembly with hot, cold, bleach, fabric softener, and jet spray valves. 12V DC solenoids. Includes 2 AGM73269501 inlet screens. Compatible with LG WT1xxx–WT7xxx and Kenmore 796-series. Replaces AJU73213301, 5221EA1008F, 5221EA1008P, AP6308239, TAW35618287, PS12374721. Common Problems This Part Fixes Washer not filling with water at all when a cycle is started Washer filling very slowly — one or more valve ports partially blocked or failing Washer filling with only hot or only cold water — one temperature solenoid has failed Washer overfilling or filling continuously — valve port stuck open Bleach dispenser not dispensing during the wash cycle Fabric softener not dispensing at the correct rinse cycle point Jet spray not activating during fill Water dripping into the tub between cycles — valve port not closing completely Water leaking from the valve body or connection points at the back of the washer Replaces Part Numbers This water inlet valve directly replaces the following OEM and cross-reference part numbers: 5221EA1008F, AJU73213301, AJU75152601, AH3527446, AJU75152603, EA3527446, PS3527446, ALG53778, AP6308239, PD00042814, PS12374721, TAW35618287. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This water inlet valve is compatible with select LG and Kenmore top-load washers from the following series: LG top-load washers — WT1 series (WT1101CW, WT1201CW, WT1201CV, WT1301CW, WT1501CW, WT1701CW, WT1701CV, WT1801HVA, WT1801HWA and related models) LG top-load washers — WT4 series (WT4801CW, WT4870CW, WT4970CW and related models) LG top-load washers — WT5 series (WT5001CW, WT5070CW, WT5101HV, WT5101HW, WT5170HV, WT5270CW, WT5480CW, WT5680HVA, WT5680HWA and related models) LG top-load washers — WT6 series (select models) LG top-load washers — WT7 series (WT7200CW, WT7200CV, WT7500CW, WT7600HKA and related models) Kenmore / Sears top-load washers — 796-series (79631512210, 79631512211, 79631522211, 79631502210, 79631502211 and related models) Note: Always verify your exact model number before ordering. Newer LG WT7100/WT7150/WT7400/WT7405 series models use the AJU75152602 valve instead. Contact our support team with your model number to confirm the correct valve for your washer. Key Features Multi-port valve assembly — controls hot water, cold water, bleach dispenser, fabric softener dispenser, and jet spray from a single replaceable assembly 12V DC solenoid operation — responds to signals from the washer's control board to deliver the correct water to each compartment Resolves fill, dispenser, overfill, and drip-when-off symptoms in a single replacement Kit includes complete valve assembly and 2x AGM73269501 replacement inlet screens ABS plastic and stainless steel construction — durable and resistant to mineral buildup Replaces AJU73213301, 5221EA1008F, 5221EA1008P, AP6308239, TAW35618287, and over 10 additional cross-reference numbers Compatible with LG WT1xxx through WT7xxx and Kenmore 796-series top-load washers Aftermarket replacement built to OEM-equivalent quality standards DIY repair — installs in 15–25 minutes with basic hand tools Product Specifications Part Number AJU75152601 Also Replaces AJU73213301, 5221EA1008F (current supersession) Part Type Washer Water Inlet Valve Assembly (Multi-Port) Condition Aftermarket Replacement Application LG and Kenmore Top-Load Washers Valve Ports Hot water, cold water, bleach dispenser, fabric softener dispenser, jet spray Solenoid Voltage 12V DC Material ABS plastic / Stainless steel Kit Includes Valve assembly + 2x AGM73269501 inlet screens Compatible Series LG WT1xxx, WT4xxx, WT5xxx, WT6xxx, WT7xxx; Kenmore 796-series Compatible Brands LG, Kenmore Installation Notes ⚠️ Unplug Washer and Shut Off Water Before Starting Disconnect power and turn off both the hot and cold water supply valves before beginning. Pull the washer away from the wall to access the back panel. The water inlet valve assembly is mounted on the upper rear of the washer — the external supply hoses connect to the hot and cold inlet ports. Photograph all wire harness connections and hose routing before disconnecting anything. Before installing, install the new inlet screens (AGM73269501) included in the kit into the hot and cold inlet ports of the new valve. Disconnect the old valve's external supply hoses, internal hoses, and wire harness connectors. Unscrew the mounting screws and remove the old valve. Install the new AJU75152601 valve, reconnect all hoses and wire harnesses in the same positions as documented in your photos, and secure the mounting screws. Reconnect the external supply hoses, restore water supply and power, and run a fill cycle to verify proper filling, confirm all dispenser ports activate at the correct cycle points, and check for leaks. Tools needed: Phillips screwdriver, pliers. Frequently Asked Questions What is the difference between AJU75152601, AJU73213301, and 5221EA1008F? These are all part numbers for the same LG washer water inlet valve assembly used across different production runs. 5221EA1008F was the original part number, AJU73213301 was an updated version, and AJU75152601 is the current part number. All three are interchangeable. If your washer's documentation, parts diagram, or old valve label shows any of these numbers, this replacement is the correct current part to order. My washer won't dispense fabric softener — is this the right part? Yes — the fabric softener dispenser solenoid is one of the ports integrated into the AJU75152601 valve assembly. When the fabric softener dispenser fails to activate at the right point in the rinse cycle, it is almost always because the solenoid valve controlling that port has failed. Since it is part of the same multi-port valve assembly, replacing the AJU75152601 resolves fabric softener, bleach, and jet spray dispenser issues in the same repair. Individual ports cannot be replaced — the complete assembly must be replaced when any one port fails. What are the AGM73269501 inlet screens included in the kit? The AGM73269501 screens are small mesh filters that install inside the hot and cold water inlet ports of the valve. They trap mineral deposits and debris from the household water supply before they can reach the valve seats and solenoid mechanisms. The kit includes two screens — one for the hot inlet and one for the cold inlet. Installing these fresh screens with the new valve helps extend valve life, especially in areas with hard water. If the old valve failed due to mineral clogging rather than solenoid failure, cleaning the supply hoses before installation is also recommended. How do I know if the water inlet valve has failed vs. the control board? You can test the valve solenoids with a multimeter. Disconnect the harness from a solenoid coil and probe both terminals — a working solenoid coil shows a resistance reading (typically 200–500 ohms); an open circuit confirms the solenoid has failed. If all solenoid coils test good but the valve still does not operate, the control board may not be sending the correct 12V DC signal to the solenoids — this requires checking voltage at the solenoid connectors with the washer powered and in a fill cycle, which is a more advanced diagnostic step. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine LG OEM part, but is manufactured from ABS plastic and stainless steel to match the port configuration, solenoid specifications, and dimensions of the original AJU75152601 water inlet valve assembly. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO WE01X30638 Laundry Center Control Knob The XPARTCO WE01X30638 is an aftermarket replacement control knob compatible with select GE, Hotpoint, RCA, and Kenmore GE-built laundry centers (stacked washer/dryer combination units). The control knob mounts on the timer or cycle selector shaft on the laundry center's control panel — it's what you grip and turn to choose wash cycles, dry cycles, and timer settings on both the washer and dryer sections of the unit. Because a stacked laundry center's knobs get twice the daily use of a standalone appliance (one control panel serving both washer and dryer functions), cracked and stripped knobs are one of the most common repairs on these units. Constructed from durable black ABS plastic with a polished silver edge ring and an internal metal plate insert that grips the D-shaped control shaft — allowing precise detent positioning so you land exactly on your desired cycle setting. Approximately 2" in diameter with thick inner walls to resist the cracking that plagues aging original knobs. Snap-on installation — pulls straight off, pushes back on, no tools required. This is the current production version, directly superseding WE01X24776. It also replaces 4961358, AP6996856, PS16226089, and EAP16226089. Installs in under 1 minute — no tools required. Quick Answer The XPARTCO WE01X30638 Laundry Center Control Knob replaces a cracked, stripped, or missing control knob on GE, Hotpoint, RCA, and Kenmore GE-built stacked laundry centers. Black ABS plastic with polished silver edge, ~2" diameter, internal metal plate for a firm shaft grip. Snap-on — no tools required. Current part superseding WE01X24776; also replaces 4961358, AP6996856, PS16226089, EAP16226089. Compatible with GE GUD27ESPM0DG, GUD27ESPM1DG, GUD27GSPM0DG, GUD27GSPM1DG and related GUD27 series laundry centers. Common Problems This Part Fixes Control knob cracked or split from age and repeated use — the most common failure on GUD27-series laundry centers Knob spinning freely on the shaft — internal grip stripped, no longer changing settings when turned Knob difficult to turn or not responding — worn internal metal plate no longer engaging the shaft Knob missing entirely from the control panel Knob loose and wobbling on the shaft — imprecise cycle selection Hairline cracks visible around the knob's shaft opening — early-stage failure that will soon strip Knob damaged from impact or overtightened grip Replacing multiple aging knobs at once — original knobs from the same production era tend to crack around the same time Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This laundry center control knob directly replaces the following OEM and cross-reference part numbers: WE01X30638, WE01X24776, AGE25575, AP6996856, EAP16226089, PD00068517, PS16226089. WE01X30638 is the current production part superseding WE01X24776. Contact our support team with your model number if you need confirmation before ordering. Compatibility This control knob is compatible with select laundry centers (stacked washer/dryer units) from the following brands: GE laundry centers — GUD27ESPM0DG (electric dryer) and GUD27ESPM1DG series GE laundry centers — GUD27GSPM0DG (gas dryer) and GUD27GSPM1DG series GE laundry centers — related GUD27 series models (verify with parts diagram) Hotpoint laundry centers (select GE-built models) RCA laundry centers (select GE-built models) Kenmore / Sears laundry centers (select GE-built models) Tip: If one knob on your laundry center has cracked, inspect the others — knobs from the same production era typically develop cracks around the same time. Since the replacement takes seconds and the knobs are identical, many customers order two or more at once and replace them all in a single session, avoiding a repeat order a few months later. This knob is approximately 2" in diameter — confirm your original knob's size matches before ordering. Key Features Control knob for laundry center timer and cycle selection — installs on the control panel shaft Durable black ABS plastic construction with thick inner walls — resists the cracking common on aging original knobs Polished silver edge ring for a clean, modern look that matches GE laundry center styling Internal metal plate insert grips the D-shaped control shaft firmly — precise detent positioning for accurate cycle selection Approximately 2" diameter with smooth mirror-polished surface for a comfortable grip Snap-on installation — pulls straight off the shaft, pushes back on; no tools or hardware required Current production part — directly supersedes WE01X24776 Replaces 4961358, AP6996856, PS16226089, and EAP16226089 Compatible with GE GUD27ESPM0DG/1DG and GUD27GSPM0DG/1DG laundry centers, plus Hotpoint, RCA, and Kenmore GE-built models Aftermarket replacement built to OEM-equivalent quality standards Quick replacement — installs in under 1 minute Product Specifications Part Number XPWE01X30638 Supersedes WE01X24776 Part Type Laundry Center Control Knob (Timer / Cycle Selector) Condition Aftermarket Replacement Application Laundry Centers / Stacked Washer-Dryer Units (GE platform) Diameter Approximately 2" Color Black with polished silver edge Material ABS plastic with internal metal plate insert Shaft Type D-shaped shaft receiver Installation Snap-on — no tools required Compatible Brands GE, Hotpoint, RCA, Kenmore (GE-built) Installation Notes ⚠️ Unplug Laundry Center Before Starting — Quick Toolless Replacement Disconnect power before beginning as a general safety precaution. Locate the old control knob on the laundry center's control panel. Grip the knob firmly and pull it straight off the control shaft — it should come off with a moderate pull (no tools required). If the knob is cracked and spinning without releasing, wrap a soft cloth around it for extra grip, or gently pry it off with a plastic tool (avoid metal tools that could scratch the control panel). Once the old knob is off, inspect the metal control shaft — note the D-shape (flat side) of the shaft. If the shaft itself is damaged, worn round, or the timer behind it feels loose, the underlying timer or switch may also need attention. Align the new WE01X30638 knob's internal D-shaped receiver with the flat side of the shaft and push it firmly straight on until it seats fully. Rotate the knob through its full range to confirm it clicks into each detent position cleanly and the indicator lines up with the panel markings. Restore power and run a quick test cycle. If replacing multiple knobs, repeat for each position — they're all identical on compatible GUD27-series units. Tools needed: None (soft cloth optional). Frequently Asked Questions Why do the knobs on my GE laundry center keep cracking? The original knobs on GUD27-series laundry centers are subject to constant rotational stress concentrated at the D-shaped shaft opening — and on a stacked laundry center, one control panel serves both the washer and dryer, so the knobs see roughly double the daily turning of a standalone appliance's controls. Over years of use, hairline cracks form at the shaft opening and gradually spread until the knob's grip strips and it spins freely. The replacement knob's thick inner walls and internal metal plate insert are designed to resist this failure pattern. If one of your knobs has cracked, check the others — knobs from the same production era typically crack around the same time, and replacing them together saves a repeat order. What's the difference between WE01X30638 and WE01X24776? These are the same control knob across production revisions. WE01X24776 was the earlier GE part number, and WE01X30638 is the current production version that GE issued as its direct replacement. Both are physically and functionally interchangeable — if your laundry center's parts diagram shows WE01X24776, the WE01X30638 is the correct current replacement, and this listing covers both numbers. There may be a very slight color variation between the new knob and your aged originals, but the fit and function are identical. How do I remove the old knob if it's cracked and just spins? When the internal grip has stripped, the knob spins on the shaft instead of pulling off cleanly. Wrap a soft cloth around the knob for extra grip and pull firmly straight out while wiggling slightly. If that doesn't work, gently work a plastic pry tool (a plastic putty knife or old credit card) behind the knob's base and lever it outward evenly around its circumference. Avoid metal tools, which can scratch the control panel. If the knob is badly cracked, you can also carefully break away the remaining plastic to free it from the shaft. Once removed, the new knob pushes straight on. Does this knob work for both the washer and dryer controls on my laundry center? Yes — on compatible GUD27-series laundry centers, the control knobs across the panel are the same part, whether they operate washer cycle selection, dryer timer, or other rotary controls that use the same D-shaped shaft. If you're replacing more than one knob, a single part number covers all matching positions. Just confirm each position's knob is the same ~2" diameter style before ordering multiples — if your unit has a visibly different-sized knob at any position, verify against the parts diagram first. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine GE OEM part, but is manufactured from durable ABS plastic with an internal metal plate insert to match the dimensions (~2" diameter), D-shaped shaft receiver, snap-on installation, and appearance of the original WE01X30638/WE01X24776 control knob used in compatible GE, Hotpoint, RCA, and Kenmore GE-built laundry centers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO W11168743 Washer Water Valve (Hot Side) The XPARTCO W11168743 is an aftermarket replacement hot water inlet valve for Whirlpool-built top-load washers. This is a single-solenoid valve dedicated to the hot water supply — it has one hose fitting inlet and one water outlet, and its only job is to open when the control calls for hot water and close again once the correct fill level is reached. This platform pairs the hot valve with a separate two-solenoid cold valve (sold separately as W11168740), so the hot and cold sides are independent components rather than one combined valve body. Because it's a dedicated single-function valve, a failure here produces a distinctive symptom: hot-only fills stop working or slow down dramatically, while cold fills (governed by the separate cold valve) continue working normally on their own. Common failure causes include mineral or sediment buildup that prevents the valve from sealing fully, a burned-out solenoid coil, or a worn rubber grommet or gasket at the push-on outlet connection. It directly replaces WPW10240948, W10240948, W10921515, 33390068, 4585634, AP6327638, PS12348074, and EAP12348074. Quick Answer The XPARTCO W11168743 Washer Water Valve (Hot Side) fixes Whirlpool-built top-load washers where hot water won't fill, fills slowly, overfills, leaks into the drum when off, or fails to stop filling. Single-solenoid hot-only valve, 120V, 60Hz, standard hose fitting inlet with push-on outlet connection. Replaces WPW10240948, W10240948, W10921515, 33390068, 4585634, AP6327638, PS12348074, EAP12348074. This is the hot-side valve only — the companion cold-side valve is sold separately as W11168740. Common Problems This Part Fixes Washer won't fill with hot water while cold water fills normally Hot water fills much more slowly than it used to Washer overfills or won't stop filling Water leaking or trickling into the drum on the hot side when the washer is off Washer not washing properly due to insufficient hot water reaching the drum Cycle stalling at the fill step and never advancing to wash No hot water reaching the washer despite the water heater and supply line working correctly Water pooling underneath or behind the washer near the hot supply connection Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer hot water inlet valve directly replaces the following OEM and cross-reference part numbers: W11168743, WPW10240948, W10240948, W10921515, 33390068, 4585634, AP6327638, AWP43142, PD00040928, PS12348074, EAP12348074 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This hot water inlet valve is compatible with select Whirlpool-built top-load washers across the Whirlpool family of brands, including: Whirlpool top-load washers (select models) Maytag top-load washers (select Whirlpool-built models) KitchenAid, Jenn-Air, and Amana top-load washers (select models) Inglis, Magic Chef, Crosley, Norge, Modern Maid, and Caloric top-load washers (select models) Roper, Admiral, Hardwick, and Estate top-load washers (select models) Select Kenmore and Ikea top-load washers built on the Whirlpool platform Note — hot side only, and a different platform than our front-load valves: This is the hot water valve for Whirlpool's top-load platform. The matching cold water valve for these same washers is sold separately under part number W11168740 — the two are not interchangeable. This part is also a different valve family entirely from the front-load W11688994 (hot) / W11688995 (cold) valves elsewhere in our catalog; those fit a different washer platform and will not work here. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure which valve fits your washer. Key Features Aftermarket replacement single-solenoid hot water inlet valve for Whirlpool-built top-load washers Standard hose fitting inlet with a single push-on water outlet and rubber grommet seal Resolves "won't fill with hot water," "fills slowly," "overfills," and "won't stop filling" symptoms caused by valve failure Rated 120V, 60Hz Approximately 3-1/2"L x 3-1/2"W x 2-1/4" deep Direct drop-in replacement — no modification required Replaces WPW10240948, W10240948, W10921515, 33390068, 4585634, AP6327638, PS12348074, and EAP12348074 Compatible with a wide range of Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Inglis, Magic Chef, Crosley, Roper, and Kenmore top-load washers Aftermarket replacement built to OEM-equivalent quality standards Product Specifications Part Number XPW11168743 OEM Part Number W11168743 Part Type Washer Water Inlet Valve — Hot Side Condition Aftermarket Replacement Application Top-Load Washers (Whirlpool-Built) Voltage 120V Frequency 60 Hz Solenoids 1 (dedicated hot water function) Inlet Connection Standard hose fitting Outlet Connection Push-on with rubber grommet Dimensions Approx. 3-1/2"L x 3-1/2"W x 2-1/4" deep Companion Part W11168740 (cold water valve, sold separately) Quantity 1 valve Compatible Brands Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Inglis, Magic Chef, Crosley, Roper, Kenmore Installation Notes ⚠️ Shut Off Water Supply And Unplug Washer Before Starting — Have A Towel Ready Unplug the washer or shut off its circuit breaker, and shut off both the hot and cold water supply valves before beginning. Wear work gloves. Disconnect the hot water supply hose from the back of the valve first — have a towel or shallow pan ready, since residual water will spill out. Remove the rear screws securing the top panel, then slide the panel back and lift it off to access the valve assembly from inside the cabinet. Photograph the wiring connections before disconnecting anything, since the hot and cold valves sit next to each other and it's easy to cross a wire. Disconnect the electrical connector from the old hot valve, disconnect the push-on outlet hose (check the rubber grommet for wear and replace it if it looks flattened or cracked), remove the mounting screw or bracket, and pull the valve free — leave the cold valve (W11168740) undisturbed if it isn't also being replaced. Install the new W11168743 in the same position, secure the mounting screw, reconnect the electrical connector, and press the outlet hose back onto its fitting with the grommet properly seated. Reattach the hot water supply hose, tightening securely by hand plus a partial turn with pliers. Reinstall the top panel, restore the water supply, and check every connection you touched for leaks before restoring power. Run a short cycle and confirm hot water fills at the normal rate with no leaking underneath or behind the washer. Tools needed: Phillips screwdriver, nut driver, pliers, towel or shallow pan, work gloves. Frequently Asked Questions Hot water won't fill but cold water works fine. Is this the right part? Yes — that's exactly the symptom pattern this valve addresses. Since your washer uses separate hot and cold valves rather than one combined valve, a fault on the hot side only affects hot fills while the cold valve keeps working independently. If hot-specific cycles are the ones failing while cold cycles are unaffected, this hot-side valve is the correct part to replace. Do I need to replace both the hot and cold valves at the same time? Not necessarily. Since these are independent single-function valves, you only need to replace the one that's actually failed. If only hot fills are affected, replacing this W11168743 valve alone is sufficient. Some people choose to replace both while the top panel is already off, especially on an older washer, but it isn't required. Is this the same valve used on your front-load washer listings? No. This valve is built for Whirlpool's top-load platform. The front-load hot/cold valve pair in our catalog (W11688994 and W11688995) is a completely different part family for a different washer design, and the two are not interchangeable. Always check whether your washer is a top-load or front-load model, and verify your exact model number, before ordering either. My washer has no hot water at all, but the water heater is working. What should I check first? Before assuming the valve has failed, confirm the hot water supply valve at the wall behind the washer is fully open, check the inlet screen inside the valve port for sediment or debris that could be restricting flow, and make sure the hot supply hose isn't kinked. If those check out and hot water still isn't reaching the drum, the valve itself is the likely cause. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured to match the single-solenoid design, connection type, and dimensions of the original W11168743 hot water valve used in compatible Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Inglis, and related top-load washers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

3148953CM Surface Burner Infinite Switch 240V, 7.5-9.3A switch for 8" elements. Fits specific Whirlpool electric ranges. Replaces Part Numbers: WP3148953, 3148953, 492439, AP6007658, PS11740775, WP3148953VP. Description The Infinite Control Switch is a replacement part for specific Whirlpool ranges and cooktop models. This part allows for precise adjustment of the heat level, enabling users to achieve the perfect temperature for various cooking techniques, from simmering to boiling. Causes of a bad Infinite Control Switch can range from electrical issues, such as short circuits or worn contacts, to mechanical failures within the switch itself.   This is an aftermarket part that can be used as a replacement for the OEM part. California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

WPW10619844 Washer Genuine OEM Lid Lock Assembly Replaces Part Numbers: WPW10619844, W10619844, W10059230, 3436901, 8563937, WPW10619844VP, AP6023438, PS11756782.  Description: This Lid Lock Assembly is a Genuine OEM part for specific Maytag, Kenmore, Whirlpool washing machine models. It ensures the washer lid is securely locked during operation, preventing it from being opened mid-cycle and ensuring safe and efficient washing. Common causes of a bad lid lock assembly can include wear and tear from frequent use, electrical issues such as short circuits, and physical damage from impact or mishandling. A malfunctioning lid lock can disrupt the washing cycle, leading to incomplete washes or safety concerns.

Read more less

WP3363892 Washer Genuine OEM Drain Pump Drain pump for belt-less direct-drive washer Oversized 1-3/4" outlet with flapper with back flow flapper valve Replaces Part Numbers:3363892, 3352496, AP6008110, PS11741242, WP3363892VP, B002CRSNT4, LP121   California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

W11220230 Washer Genuine OEM Water Valve – Compatible with Whirlpool, Maytag, Amana, Crosley, Roper Washers Product Description Keep your washer filling properly with the W11220230 Washer Genuine OEM Water Valve. This factory-approved valve regulates hot and cold water flow into the tub during wash cycles. A faulty valve can cause filling issues, leaks, or error codes. Replacing it with this genuine OEM part ensures dependable performance and efficient cleaning. Replaces Part Numbers W11220230, W10853296, 4591408, W10632527, W10758829, W11096268, PD00042661, EAP12349461, AP6329544, PS12349461. Compatibility This water valve is compatible with select Whirlpool, Maytag, Amana, Crosley, and Roper washers. Example compatible models include (but are not limited to): Whirlpool WTW5000DW3, Maytag MVWC465HW2, and Amana NTW4516FW3. Always verify your washer’s model number before ordering. Contact our support team if you’re unsure. ✅ Key Features 🔄 Genuine OEM Part – Designed for Whirlpool, Maytag, Amana, Crosley, and Roper washers 💧 Reliable Water Control – Ensures accurate water flow and filling cycles 💰 Cost-Effective OEM Repair – Long-lasting factory-tested replacement 🛠️ DIY Friendly – Installs in 20–30 minutes with basic tools 🛡️ Fixes Common Issues – Resolves filling problems, leaks, and error codes 📐 Product Specification Part Number: W11220230 Component Type: Washer Water Inlet Valve Material: Reinforced plastic body with solenoid valves Mounting: Direct-fit replacement Operating Conditions: Designed for residential washer use Compliance: Genuine OEM certified 🛠️ Installation Notes Tools Needed: Phillips screwdriver, pliers, adjustable wrench ⚠️ Safety First: Unplug washer and turn off water supply before beginning repairs. Steps: Disconnect washer from power and water supply. Remove back panel to access the water valve. Disconnect hoses and wiring harness from the old valve. Unscrew and remove the defective valve. Install the new W11220230 valve, reconnect hoses and wiring. Reassemble panel, restore water and power, and run a test cycle. ⏱️ Time Required: 20–30 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders 🛠️ Trusted Appliance Parts Supplier 🔄 30-Day Return Policy Fix washer filling issues today — Add to Cart Now for a safe, factory-approved repair!

Read more less