WH23X38617 Genuine OEM GE Washer Drain Pump Filter with Seal
The WH23X38617 is a Genuine OEM GE replacement drain pump filter with seal, compatible with select GE, GE Profile, and GE 2-in-1 Washer/Dryer Combo models. The pump filter sits inside the drain pump housing and traps lint, coins, hair, and small debris before they reach the pump impeller. Keeping this filter clean and intact is essential for proper drainage — a clogged or damaged filter causes slow draining, standing water in the tub, and can strain the drain pump over time.
This genuine OEM part is manufactured by GE to factory specifications and includes both the pump filter and the seal. The seal prevents leaks at the pump clean-out when the filter is installed correctly. The filter body is blue plastic with rubber seal components, measuring approximately 6" L x 3" W x 3" H. It directly replaces part number AP7243923 and installs with a simple counterclockwise removal and clockwise installation — no special tools required.
Quick Answer
The WH23X38617 Genuine OEM GE Washer Drain Pump Filter with Seal fixes GE washers that drain slowly, leave standing water in the tub, or leak near the pump access panel. The filter traps lint and debris to protect the pump impeller. Includes filter and seal. Blue plastic/rubber, approx. 6" L x 3" W x 3" H. Twist-out installation — no tools needed. Compatible with GE, GE Profile, and GE 2-in-1 Washer/Dryer Combo models.
Common Problems This Part Fixes
Washer draining slowly or not draining at all after a wash cycle
Standing water remaining in the drum at the end of a cycle
Water leaking from the pump filter access panel at the front of the washer
Error codes related to drain or pump failure on compatible GE models
Unusual noise from the drain pump caused by debris reaching the impeller
Cracked, stripped, or missing filter cap allowing debris into the pump housing
Damaged or deteriorated seal causing leaks at the filter access port
Replaces Part Numbers
This drain pump filter directly replaces the following part numbers:
WH23X38617, WH23X38617, FIX17874614, AGE1014282, PD00090185, AP7243923, PS17874614.
Contact our support team with your model number if you need help confirming compatibility before ordering.
Compatibility
This drain pump filter is compatible with select washers and laundry centers from the following GE product lines:
GE front-load washers (select models)
GE Profile front-load washers (select models)
GE 2-in-1 Washer/Dryer Combo (select models)
Always verify your appliance model number before ordering. Contact our support team if you're unsure.
Key Features
Genuine OEM part manufactured by GE to factory specifications — guaranteed fit and performance
Traps lint, coins, hair, and small debris to protect the drain pump impeller from damage
Includes both the pump filter and seal — everything needed for a complete replacement
Seal prevents water leaks at the pump filter access port when the filter is properly installed
Blue plastic and rubber construction — durable and chemical resistant
Dimensions: approximately 6" L x 3" W x 3" H
Twist-out installation — turns counterclockwise to remove, clockwise to install; no special tools required
Should be cleaned regularly (every 1–3 months) and replaced when cracked, stripped, or leaking
Product Specifications
Part Number
WH23X38617
Part Type
Washer Drain Pump Filter with Seal
Condition
Genuine OEM
Application
Front-load washers and 2-in-1 washer/dryer combos
Approximate Dimensions
6" L x 3" W x 3" H
Color
Blue
Material
Plastic / Rubber
Includes
Pump filter and seal
Installation
Twist-out / twist-in — no special tools required
Compatible Brands
GE, GE Profile
Installation Notes
⚠️ Unplug Washer and Shut Off Water Before Starting Disconnect power and turn off the water supply before servicing the drain pump filter. Place towels or a shallow pan beneath the filter access panel to catch residual water — there will always be some water remaining in the pump housing when you remove the filter. Locate the pump filter access panel at the lower front of the washer and open or remove it. Turn the old WH23X38617 filter counterclockwise to loosen and remove it. Clear any debris from the filter housing and wipe the area clean. Install the new filter and seal by inserting it into the housing and turning it clockwise until snug — do not overtighten. Close or reinstall the access panel, restore water supply and power, then run a short cycle to verify proper drainage and confirm there are no leaks at the filter port. Tip: Clean the pump filter every 1–3 months as part of regular washer maintenance to prevent buildup. Tools needed: None for the filter itself; a screwdriver may be needed to open the access panel on some models.
Frequently Asked Questions
What does the drain pump filter do?
The drain pump filter catches lint, coins, hair, buttons, and other small items before they can reach the drain pump impeller. Without the filter, debris can jam or damage the impeller — leading to pump failure, loud grinding noises, or a washer that won't drain. The filter also acts as a cleanout access point so you can periodically remove accumulated debris without disassembling the pump.
How often should I clean or replace the pump filter?
GE recommends cleaning the pump filter every 1–3 months depending on how frequently you run the washer and how much lint your laundry produces. The filter should be replaced rather than just cleaned if it is cracked, stripped at the threads, or if the seal is damaged or missing — a compromised filter or seal will leak water from the access port.
Why is water leaking from the front of my GE washer near the bottom?
A leak at the lower front of the washer near the pump access panel is most often caused by a damaged or deteriorated pump filter seal, a cracked filter body, or a filter that is not fully tightened. Replacing the WH23X38617 pump filter and seal resolves this in most cases. Make sure the new filter is hand-tightened snugly — do not overtighten, as this can crack the housing.
Will there be water when I remove the pump filter?
Yes — there is always residual water in the drain pump housing. Before removing the filter, place towels and a shallow pan or tray directly under the access panel to catch the water. The amount varies depending on how much water remains in the washer after the last cycle. Running a drain-only cycle immediately before removing the filter will minimize the amount of water released.
Is this a Genuine OEM or aftermarket part?
This is a Genuine OEM part manufactured by GE to factory specifications. It is the exact same pump filter and seal that GE installs in compatible models from the factory — guaranteed fit, materials, and performance.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
Genuine OEM WP3406107 Dryer Door Switch
The Genuine OEM Whirlpool WP3406107 is a dryer door switch for Whirlpool, Kenmore, Maytag, and KitchenAid dryers. It mounts inside the top of the dryer's front panel, with one end connecting to the wiring harness and the other passing through the panel to make contact with the door. When the door closes, it presses the switch's black tab, which tells the dryer the door is shut so it can run. When the switch wears out, the dryer may not start, may run with the door open, or may lose its interior light.
This is the original Whirlpool part, a white, 6.5 inch, three-wire switch. Retailers describe the switch as a regular wear part and rate the repair as really easy, typically 15 to 30 minutes.
Quick Answer
The Genuine OEM WP3406107 Door Switch fixes a Whirlpool, Kenmore, Maytag, or KitchenAid dryer that won't start, runs with the door open, has a light that doesn't work, or has a door that won't close properly. Quick test: with the dryer unplugged, press the switch's black tab. If it has no resistance and doesn't click, the switch likely needs replacing.
Common Problems This Part Fixes
Dryer won't start
Dryer runs with the door open
Interior light doesn't work
Door won't close or latch properly against the switch
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This door switch directly replaces the following part numbers:
WP3406107, WPW10569603, 3406107, W10569603, 3405100, 3405101, 3406100, 3406101, 528948, 11259-65, 11288-80, WP3406107VP, AP6008561, AWP47183, EAP11741701, PD00002378, PS11741701
These numbers come from retailer cross-reference lists and span several generations of Whirlpool's own numbering for this switch. Confirm against your dryer's parts diagram, or contact our support team, if your model calls out a different number.
Compatibility
This door switch is listed for Whirlpool, Kenmore, Maytag, and KitchenAid dryers, including these examples:
Kenmore 11060372710, 11060522900, 11060702990, 11060802990
Kenmore 11061202010, 11061262311, 11061802000
Whirlpool EED4400WQ
Note: The models above are a small sample of a longer list, not a full list. This is a three-wire switch that replaces the two-wire switch found on many models, so compare it to your old switch, and contact our support team with your model number to verify fit before ordering.
Key Features
Genuine OEM Whirlpool dryer door switch, not an aftermarket equivalent
Three-wire design; replaces the two-wire switch on many models
White, 6.5 inch switch with a spring-loaded black tab
Resolves no-start, runs-with-door-open, and light problems caused by a worn switch
Typically a 15 to 30 minute repair
Product Specifications
Part Number
WP3406107
OEM Part Number
WP3406107
Part Type
Dryer Door Switch
Condition
Genuine OEM
Manufacturer
Whirlpool
Length
6.5 Inches
Color
White
Wire Configuration
Three-Wire
Application
Whirlpool, Kenmore, Maytag & KitchenAid Dryers
Installation Notes
⚠️ Unplug Power Before Installing Unplug the dryer before beginning, and shut off the gas supply first on gas models. Wear work gloves, as cabinet edges can be sharp. The switch is mounted inside the top of the front panel, so follow your model's service guide to remove the panel needed to reach it. Note how the wiring connector is attached, disconnect it, and remove the old switch. Fit the new switch in the same position, reconnect the wiring, and reassemble. Restore power and confirm the dryer starts with the door closed and stops when the door is opened.
Frequently Asked Questions
My dryer won't start. Is this the part I need?
A worn door switch is a common cause. With the dryer unplugged, press the switch's black tab. If there is no resistance and no click, the switch likely needs replacing.
My dryer runs with the door open. Is that a problem?
Yes. The door switch is a safety part that stops the dryer from running when the door is open. If the dryer runs with the door open, replace the switch promptly.
My dryer has a two-wire switch. Will this three-wire switch work?
Retailers list this three-wire switch as the replacement for the two-wire switch found on many models. Compare it to your old switch and your wiring, or contact our support team with your model number, before ordering.
Will this fit my dryer?
It is listed for many Whirlpool, Kenmore, Maytag, and KitchenAid dryers, but the model list above is only a sample. Check your model number against your parts diagram, or contact our support team and we'll verify it before you order.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping ✓ Genuine OEM Parts ✓ Compatibility Support ✓ Secure Checkout
ERP DC97-05280W Washer Suspension Rod
Replaces Part Numbers: DC97-05280W, 3998024, AP5966911, PS11719937
This is an aftermarket part that can be used as a replacement for the OEM part.
California Residents only
WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov
DC31-00098A Washer Rotor Position Sensor
Replaces Parts Numbers: DC31-00098A, 2068316, AP4578642, PS4204673, B084RT6G78
Description: The Washer Rotor Position Sensor ensures precise motor function for your washer. This replacement part accurately detects the rotor's position, enabling smooth and efficient washing cycles. By maintaining optimal motor performance, it helps prevent unexpected interruptions and extends the lifespan of your appliance. Compatible with specific Samsung washer models, this rotor position sensor guarantees a secure fit and reliable operation.
This is an aftermarket part that can be used as a replacement for the OEM part.
5304506510 Dishwasher Dish Rack Rail End Cap - Compatible with Frigidaire, Electrolux.
Product Description
Keep your dishwasher rack stable with the 5304506510 Dish Rack Rail End Cap from Parts-O-Matic. This genuine OEM replacement end cap prevents the upper dish rack from sliding off the rails, ensuring safe and easy loading/unloading. Designed for Frigidaire, Electrolux dishwashers, it fixes issues like rack instability or falling out.
Note: Includes one rail end cap. Inspect rack rollers for wear .
Replaces part numbers: 5304506510, 5304440996, 4456332, PD00046626, EAP11770481, AP6036334, PS11770481.
Compatibility:
Compatible with models including but not limited to:
Frigidaire: FFBD2404NB10C, FFBD2406NB8B, FFBD2408NS7C, FFBD2412SB0A, FFCD2413US0A
Crosley: CDB350NB10B, CDBEH600SB0A, CDBEH950SS1A
Kenmore: 587.14022200A
Verify your model number or contact Parts-O-Matic support for assistance.
Key Features:
✅ Brand Compatibility: Fits select Frigidaire, Crosley, Kenmore, and Westinghouse dishwasher models.
🔒 Specifications: OEM gray plastic rail end cap, ~1–2" long, designed for secure rack stability.
💰 Cost-Effective: OEM performance at a competitive price.
🛠️ Easy Installation: Requires a flat-blade screwdriver; typically installed in 5–10 minutes.
🛡️ Reliable Fixes: Resolves rack sliding off rails, instability, or falling out.
Installation Notes:
Safety First: Unplug the dishwasher before installation (typically not needed for this repair).
Use a flat-blade screwdriver to pry open the locking tab on the old end cap (front of upper dish rack rail), remove it, and snap the new cap into place.
Inspect rack rollers and rails for wear to ensure stability.
Watch YouTube tutorials for model-specific guidance.
Shop Parts-O-Matic for high-quality replacement appliance parts with a 30-day return policy. Keep your dishwasher running smoothly today!
Add to cart now for a budget-friendly fix!
W10844024 Genuine OEM Whirlpool Dishwasher Water Inlet Valve
The W10844024 is a genuine Whirlpool OEM water inlet valve for Whirlpool, Kenmore, KitchenAid, Estate, Roper, Inglis, Maytag, Crosley, Ikea, Magic Chef, Kirkland, and Amana dishwashers. This valve regulates the flow of water into the appliance during each fill stage of the wash cycle, opening and closing to admit the correct amount of water at the right times.
Weighing approximately 0.2 lbs, common failure causes include mineral or sediment buildup inside the valve and general electrical wear in the solenoid. A failing valve produces a clear set of symptoms: the dishwasher not filling with water at all, or a valve that's unusually noisy — starting and stopping repeatedly — during heavy wash cycles as it struggles to regulate flow correctly. It directly replaces 3384890, 8283346, 9744468, W10219643, WP9744468, WPW10219643, 3378779, 3379356, 4383567, 8274221, 8283345, 9743175, 9743559, 9744029, 9744284, W10327248, W10844024VP, AP5989613, AWP42052, EAP11730996, PD00032565, PS11730996
Quick Answer
The W10844024 Genuine OEM Whirlpool Dishwasher Water Inlet Valve fixes Whirlpool, Kenmore, KitchenAid, Estate, Roper, Inglis, Maytag, Crosley, Ikea, Magic Chef, Kirkland, and Amana dishwashers that aren't filling with water, or that are unusually noisy — starting and stopping — during heavy wash cycles. Replaces 3384890, 8283346, 9744468, W10219643, WP9744468, WPW10219643, 3378779, 3379356, 4383567, 8274221, 8283345, 9743175, 9743559, 9744029, 9744284, W10327248, W10844024VP, AP5989613, AWP42052, EAP11730996, PD00032565, PS11730996. Some households need a separate hose adapter for this valve if the existing water line connector has a smaller diameter than the new valve's fitting — check before you start, or be prepared for a quick hardware store trip.
Common Problems This Part Fixes
Dishwasher not filling with water at all
Valve unusually noisy — starting and stopping repeatedly during heavy wash cycles
Cycle stalling at the fill step and never advancing to wash
Poor washing results due to insufficient water fill
Leaking near the valve connections
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This dishwasher water inlet valve directly replaces the following OEM and cross-reference part numbers:
W10844024, 3384890, 8283346, 9744468, W10219643, WP9744468, WPW10219643, 3378779, 3379356, 4383567, 8274221, 8283345, 9743175, 9743559, 9744029, 9744284, W10327248, W10844024VP, AP5989613, AWP42052, EAP11730996, PD00032565, PS11730996
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This water inlet valve is compatible with select Whirlpool dishwashers, and also fits select Kenmore, KitchenAid, Estate, Roper, Inglis, Maytag, Crosley, Ikea, Magic Chef, Kirkland, and Amana dishwashers built on the Whirlpool platform, including model numbers such as KUDR25SHWH1, MDB4629AWB1, DU900PWKB0, DU900PWKQ0, and Kenmore 665.15522000, 66517662991, and 66516669991.
Note: Always verify your full model number before ordering, since similar-looking dishwasher water valves can vary between models. Contact our support team with your model number if you're unsure.
Key Features
Genuine Whirlpool OEM part — factory-specified solenoid design and flow rate
Regulates water flow into the dishwasher during each fill stage of the cycle
Resolves "won't fill" and "noisy, starts and stops when filling" symptoms caused by valve failure
Factory Certified Part built to Whirlpool's engineering specifications
Direct drop-in replacement — matches the original mounting and hose connections
Replaces 3384890, 8283346, 9744468, W10219643, WP9744468, WPW10219643, 3378779, 3379356, 4383567, 8274221, 8283345, 9743175, 9743559, 9744029, 9744284, W10327248, W10844024VP, AP5989613, AWP42052, EAP11730996, PD00032565, PS11730996
Compatible with Whirlpool, Kenmore, KitchenAid, Estate, Roper, Inglis, Maytag, Crosley, Ikea, Magic Chef, Kirkland, and Amana dishwashers
Genuine OEM replacement — guaranteed fit, materials, and performance
Product Specifications
Part Number
W10844024
Part Type
Dishwasher Water Inlet Valve
Condition
Genuine OEM
Brand
Whirlpool
Weight
Approx. 0.2 lbs
Function
Regulates water flow into the dishwasher during fill
Repair Difficulty
Easy to Moderate
Quantity
1 valve
Compatible Brands
Whirlpool, Kenmore, KitchenAid, Estate, Roper, Inglis, Maytag, Crosley, Ikea, Magic Chef, Kirkland, Amana
Installation Notes
⚠️ Unplug Dishwasher And Shut Off Water Supply Before Starting — Check Your Hose Connector Size First Disconnect power at the outlet or shut off the circuit breaker, and disconnect the water lines connected to the old valve before beginning. Wear work gloves. Have a shop vacuum on hand — some customers have needed to remove standing water from the bottom of the dishwasher before starting this repair. Locate the old valve and use pliers to unscrew any screws or bolts connecting it to the appliance. Clean the area where the old valve was located, removing any debris before installing the new one. Check the diameter of your existing water line connector before starting — some households have a smaller-diameter connector than this new valve's fitting requires, in which case you'll need a separate hose adapter from a hardware store to complete the connection. Take the new W10844024 and place it in the same position as the old valve, making sure it's connected correctly, and secure any screws or bolts. Reattach the water lines to the new valve and reconnect power. Double-check all connections before restoring power, then run a test cycle to confirm the dishwasher fills correctly with no leaks. Tools needed: pliers, possibly a hose adapter, shop vacuum (if needed), work gloves.
Frequently Asked Questions
My dishwasher isn't filling with water at all. Is this the right part?
Yes, this is the most direct symptom of a failed water inlet valve. Since this valve is what admits water from your household supply into the dishwasher, a solenoid failure or internal blockage can prevent any water from entering at all, stopping the wash cycle from proceeding.
Will I need any extra parts for this installation?
Possibly. A few customers have found their existing water line connector had a smaller diameter than this valve's fitting, requiring a separate hose adapter purchased locally from a hardware store to complete the connection. It's worth checking your connector size beforehand, or having a quick trip to the hardware store planned just in case.
My dishwasher makes a noisy, start-and-stop sound when filling. Is that this valve?
Yes, this is a documented symptom. One customer described their valve as "very noisy on heavy wash cycles, started and stopped when filling" before replacing it with this exact part, which resolved the issue.
Is this an OEM or aftermarket part?
This is a genuine OEM part, manufactured by Whirlpool to factory specifications — guaranteed fit, materials, and performance. It matches the original solenoid design, flow rate, and connection type of the water inlet valve originally installed in your dishwasher.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
WR2X7054CM Dishwasher / Refrigerator Push-on Nut
Push on retainer clip.
Used on GE dishwashers and refrigerators.
Replaces Part Numbers:WR2X7054, WD02X0429, WD2X429, WR02X7054, AH298353, EA298353, AP2059046, PS298353.
This is an aftermarket part that can be used as a replacement for the OEM part.
California Residents only
WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov
8558953 Dishwasher Touchpad and Control Panel
Genuine OEM
Fits Specific Kenmore Dishwasher Models
Replaces Part Numbers: WP8558953, 8558953, 1066185, 8558928, 8563373, AP6013229, PS11746451.
California Residents only
WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov
XPARTCO W10730972 Washer Drain Pump Replaces WPW10730972
The XPARTCO W10730972 is an aftermarket replacement front-load washer drain pump and motor assembly compatible with a wide range of Whirlpool, Maytag, Kenmore, Amana, Inglis, and KitchenAid front-load washers — including the Whirlpool Duet, Maytag 2000/3000/4000 series, and Kenmore HE2/HE2T Plus. The drain pump removes water from the washer tub during the drain and spin phases of each wash cycle. When the pump fails, the washer will not drain, will leave standing water in the tub, stop mid-cycle, display error codes F21, F33, or SD, or leak from the pump area.
This complete assembly includes the motor, pump housing, and integrated filter — these components are only available as a complete assembly and are not sold separately. Rated 120V, 60Hz, 78W, 1.2A (CL.F duty class). Assembly dimensions are 8-3/4"L x 7"W x 5-1/4"H in off-white plastic housing. Note: Whirlpool redesigned this pump — the replacement may look different from the original but fits and functions identically. It directly replaces WPW10730972, W10130913, W10130913-B, 8540024, 8540025, 8540027, 8540028, 8540996, W10117829, W10183434, W10190647, W10190648, W10201457, AP6023956, PS11757304, and additional cross-reference numbers. Installs in 20–30 minutes with basic hand tools.
Quick Answer
The XPARTCO W10730972 Washer Drain Pump fixes Whirlpool Duet, Maytag 2000/3000/4000 series, and Kenmore HE2/HE2T Plus front-load washers that won't drain, leave standing water, or display error codes F21, F33, or SD. Complete assembly — motor, pump housing, and filter included. 120V/60Hz/78W/1.2A. 8-3/4"L x 7"W x 5-1/4"H. Note: redesigned — may look different from original but fits identically. Replaces WPW10730972, W10130913, 8540024, 8540996, W10117829, AP6023956, PS11757304.
Common Problems This Part Fixes
Washer not draining — standing water remaining in the tub after a cycle
Error code F21 displayed — long drain fault (washer unable to drain in allotted time)
Error code F33 displayed — pump motor fault
Error code SD displayed — suds detection or drain issue
Washer stopping mid-cycle due to a drain fault
Loud humming or grinding noise during the drain phase
Water leaking from the front lower area of the washer — pump seal failure
Pump motor running but water not being expelled from the tub
Replaces Part Numbers
This drain pump directly replaces the following OEM and cross-reference part numbers:
WPW10730972, W10730972, W10130913, 4281917, 8540024, 8540025, 8540027, 8540028, 8540996, W10117829, W10183434, W10190647, W10190648, W10201457, WPW10730972VP, AP6023956, AWP50633, B40-3A01, EAP11757304, PD00025949, PS11757304
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This drain pump is compatible with select front-load washers from the following brands and series:
Whirlpool front-load washers — Duet series (WFW8300, WFW8400, WFW9050, WFW9150, WFW9200, WFW9250, WFW9400, WFW9450, WFW9500, WFW9550, WFW9600, WFW96HEA, WFW97HED, WFW98HEB and related models)
Maytag front-load washers — 2000 series (MHW2000AW, MHW2000BWW and related models)
Maytag front-load washers — 3000 series (MHW3000BW and related models)
Maytag front-load washers — 4000 series (MHW4000BW, MHW4200BW, MHW5100DW, MHW6000AW, MHW6000XW and related models)
Kenmore / Sears front-load washers — HE2 and HE2T Plus series (110.45862400, 110.47532602 and related models)
Amana front-load washers (select models)
Inglis front-load washers (select models)
KitchenAid front-load washers (select models)
Note: Whirlpool redesigned this pump assembly — the replacement may look different from your original pump (larger in size on some versions) but is engineered to fit and function identically in all compatible models. Always verify your model number before ordering. Before replacing the pump, check and clear the coin trap/drain filter — a clogged filter is a common cause of F21/F33 errors that does not require pump replacement.
Key Features
Removes water from the tub during drain and spin cycles — essential for proper washer operation
Complete assembly — motor, pump housing, and integrated filter included; components are not sold separately
Rated 120V, 60Hz, 78W, 1.2A (CL.F) — correct electrical specifications for compatible Whirlpool-family front-load washers
Dimensions: 8-3/4"L x 7"W x 5-1/4"H — off-white plastic housing
Resolves error codes F21 (long drain), F33 (pump motor fault), and SD (suds/drain) on compatible models
Redesigned assembly — may look different from original but fits and functions identically
Replaces WPW10730972, W10130913, 8540024, 8540996, W10117829, AP6023956, and over 20 additional cross-references
Compatible with Whirlpool Duet, Maytag 2000/3000/4000 series, Kenmore HE2/HE2T Plus, Amana, Inglis, and KitchenAid
Aftermarket replacement built to OEM-equivalent quality standards
DIY repair — installs in 20–30 minutes with basic hand tools
Product Specifications
Part Number
XPW10730972
OEM Part Number
WPW10730972
Part Type
Front-Load Washer Drain Pump and Motor Assembly
Condition
Aftermarket Replacement
Application
Front-Load Washers (Duet, Maytag 2000/3000/4000, Kenmore HE2/HE2T Plus)
Voltage
120V AC
Frequency
60 Hz
Wattage
78W
Amperage
1.2A
Duty Class
CL.F
Dimensions
8-3/4"L x 7"W x 5-1/4"H
Color
Off-White
Material
Plastic housing
Includes
Motor, pump housing, and integrated filter — complete assembly
Design Note
Redesigned — may look different from original; fits identically
Error Codes Resolved
F21 (long drain), F33 (pump motor fault), SD (suds/drain)
Compatible Brands
Whirlpool, Maytag, Kenmore, Amana, Inglis, KitchenAid
Installation Notes
⚠️ Unplug Washer and Shut Off Water Before Starting — Work Gloves Recommended Disconnect power and turn off the water supply before beginning. Place towels on the floor — residual water will drain when the pump is disconnected. The drain pump is accessed through the lower front panel of the washer. Remove the screws on the lower kick panel or snap panel to expose the pump access area. Before removing the pump, drain residual water by removing the coin trap/filter cap from the filter housing (have a shallow pan ready — up to a quart of water may flow out). After draining, disconnect the pump wiring harness. Release the drain hose clamps and disconnect the hoses from the pump. Unscrew or unclip the pump mounting hardware and remove the old pump. Transfer the hoses and wiring to the new W10730972 pump, secure the mounting hardware, and reinstall the front panel. Restore power and water, run a drain/spin cycle, and check for leaks. Tools needed: Phillips screwdriver, Torx screwdriver (T20 on some models), pliers, shallow pan, towels, work gloves.
Frequently Asked Questions
What do error codes F21, F33, and SD mean on Whirlpool Duet and Maytag washers?
F21 indicates a long drain fault — the washer was unable to drain within the expected time (typically 8 minutes). F33 indicates a pump motor fault — the control board is not detecting the pump motor operating correctly. SD is a suds detection code that can also appear when drain issues prevent the suds from clearing properly. All three codes point toward the drain pump or a drain obstruction. Before replacing the pump, check and clean the coin trap filter — a clogged filter is one of the most common causes of F21 errors and clearing it often resolves the code without needing a new pump.
Should I check the coin trap filter before replacing the pump?
Yes — always check the coin trap filter before replacing the pump. On Whirlpool Duet and Maytag front-load washers, the coin trap filter is located inside the lower front access panel, typically behind a small cap or cover. Removing the cap and clearing lint, coins, and debris from the filter restores drain flow and clears F21/F33 errors in many cases without any part replacement needed. If the filter is clear and the pump still humbles or fails to drain, the pump needs replacement.
Why does the replacement pump look different from the original?
Whirlpool redesigned this drain pump assembly during its production lifecycle — the WPW10730972 replacement is physically larger than some of the older 8540024-series pumps it supersedes. Despite looking different, the redesigned pump uses the same hose and electrical connection points and is a direct fit in all compatible models. The larger housing is an intentional design improvement to increase pumping capacity. If the pump looks bigger than what you removed, this is normal and expected — install it in the same way as the original.
What is the difference between W10730972 and WPW10730972?
These are the same drain pump assembly. WPW10730972 is the updated Whirlpool OEM part number that superseded the original W10730972. The W10130913 and 8540024 are also cross-references for earlier versions of this same pump. This aftermarket replacement is compatible with all of these numbers.
Is this an OEM or aftermarket part?
This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured to match the electrical specifications and performance of the original WPW10730972 drain pump assembly.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout
