Search results for "Dryer Thermal Fuse"

XPARTCO DA47-00243K Refrigerator Defrost Thermostat The XPARTCO DA47-00243K is an aftermarket replacement defrost bi-metal thermostat compatible with select Samsung French door and bottom freezer refrigerators. This thermostat is a critical component in the automatic defrost system, functioning as a thermal safety device that monitors the temperature of the evaporator coils during the defrost cycle. When the evaporator reaches the preset maximum temperature of 140°F (60°C), the bi-metal thermostat opens the circuit and cuts power to the defrost heater — preventing overheating and damage to the evaporator. It resets and closes again at 104°F (40°C), allowing the next defrost cycle to begin normally. When the thermostat fails, it can cause excessive frost buildup on the evaporator coils, poor cooling performance, or a heater that won't shut off — all resulting in the refrigerator failing to maintain proper temperatures. Quick Answer The XPARTCO DA47-00243K Refrigerator Defrost Thermostat fixes refrigerators with excessive frost buildup, a freezer that is too cold while the fridge is too warm, a heater that won't shut off, or a refrigerator that stops cooling. It is compatible with select Samsung French door and bottom freezer refrigerators and opens at 140°F to protect the evaporator from overheating. Common Problems This Part Fixes Excessive frost or ice buildup on evaporator coils Freezer too cold while refrigerator section is too warm Defrost heater not shutting off after defrost cycle Refrigerator not cooling or maintaining temperature Food spoiling faster than normal Unusual humming or running sounds from the back of the fridge Replaces Part Numbers This thermostat directly replaces the following OEM and cross-reference part numbers: DA47-00243K, 2025696, DA47-00243B, DA47-00243C, DA47-00243J, ASM30257, PD00002154, EAP4140510, AP4403832, PS4140510. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This defrost thermostat is compatible with select refrigerators from the following brands: Samsung French door refrigerators Samsung bottom freezer refrigerators Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Bi-metal thermal safety device — opens at 140°F (60°C) to cut power to the defrost heater and prevent evaporator overheating Resets automatically at 104°F (40°C) — allowing the next defrost cycle to begin normally Aftermarket replacement built to OEM-equivalent quality standards 2-terminal design — direct drop-in replacement, no modification required Restores proper frost-free operation and refrigerator cooling performance DIY-friendly repair — installs with basic hand tools in 30–45 minutes Budget-friendly alternative to OEM at a lower cost without sacrificing performance Product Specifications Part Number DA47-00243K Part Type Defrost Bi-Metal Thermostat Condition Aftermarket Replacement Application Refrigerator Defrost System Open Temperature 140°F (60°C) Close Temperature 104°F (40°C) Terminals 2 Compatible Brands Samsung Installation Notes ⚠️ Safety First — Unplug Refrigerator Before Starting Unplug the refrigerator from the power source before beginning any repair. Safely remove and store any food that could deteriorate while the power is off. Wear work gloves to protect your hands. Access the evaporator coils by removing the rear panel inside the freezer compartment. Disconnect the wiring harness from the old thermostat and clip the new DA47-00243K thermostat onto the evaporator coil in the same position. Reconnect the wiring harness and reassemble the freezer panel. Allow 24 hours for the refrigerator to return to normal operating temperature. Consult your refrigerator's service manual for model-specific instructions. Frequently Asked Questions Will the DA47-00243K fit my Samsung refrigerator? This thermostat is compatible with select Samsung French door and bottom freezer refrigerators. Use the model search above to verify your model, or contact our support team before ordering. What does a defrost thermostat do? The defrost bi-metal thermostat monitors the temperature of the evaporator coils during the defrost cycle. It opens the circuit and cuts power to the defrost heater when the evaporator reaches 140°F (60°C), preventing overheating. It automatically resets and closes again at 104°F (40°C) to allow the next cycle. What are signs that my defrost thermostat needs replacement? Common signs include: excessive frost or ice buildup on the evaporator coils, the freezer running too cold while the refrigerator section is too warm, the defrost heater failing to shut off, or the refrigerator not maintaining proper temperatures and food spoiling faster than normal. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Samsung OEM part, but is designed to deliver reliable, long-lasting performance at a more affordable price point. At what temperatures does the DA47-00243K open and close? The thermostat opens (cuts power to the heater) at 140°F (60°C) and closes (resets) at 104°F (40°C). Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO 2188820 Refrigerator Thermistor (Sensor) Replaces WP2188820 The XPARTCO 2188820 is an aftermarket replacement refrigerator temperature sensor (thermistor) compatible with select Whirlpool, Kenmore, KitchenAid, Maytag, Jenn-Air, Dacor, and Thermador refrigerators. The thermistor is an NTC (negative temperature coefficient) sensor that continuously monitors the air temperature inside the refrigerator or freezer compartment and sends resistance-based readings to the electronic control board. The control board uses these readings to regulate compressor run time and fan operation, maintaining the set temperature accurately and efficiently. This thermistor features an NTC resistance of 50K ohms at 25°C (27K ohms at 0°C/32°F) and a standard wire length of approximately 5.3 inches (13.46 cm), compatible with low-voltage refrigerator control boards (5V/12V). It directly replaces WP2188820, 2213442, AP6006068, PS11739132, and 1057764. Note: this thermistor is compatible with non-WISE system refrigerators only — it is not compatible with newer Whirlpool refrigerators using the WISE (Whirlpool Intelligent Smart Energy) control system. Installs in under 15 minutes. Quick Answer The XPARTCO 2188820 Refrigerator Thermistor fixes Whirlpool-family refrigerators that are too warm, too cold, have erratic temperatures, run the compressor too long, or display temperature-related error codes. NTC sensor, 50K ohm at 25°C, ~5.3" wire. Non-WISE system models only. Compatible with Whirlpool, Kenmore, KitchenAid, Maytag, Jenn-Air, Dacor, and Thermador. Replaces WP2188820, 2213442, AP6006068, PS11739132. Common Problems This Part Fixes Refrigerator not maintaining set temperature — too warm or too cold Freezer section too warm or food not freezing properly Compressor running continuously without cycling off Temperature fluctuating erratically despite stable ambient conditions Refrigerator temperature-related error codes displayed on the control panel Excessive frost buildup caused by incorrect temperature regulation Food or beverages freezing in the fresh food section Replaces Part Numbers This refrigerator thermistor directly replaces the following OEM and cross-reference part numbers: WP2188820, 2188820, 2213442, EAP11739132, AWP46934, PD00033406, AP6006068, PS11739132. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This thermistor is compatible with select refrigerators from the following brands and series: Whirlpool refrigerators — 5VW, GC3, EC3, GC5 series Kenmore / Sears refrigerators — 106 series (Whirlpool-built models) KitchenAid refrigerators — KSCS, KSSS, JS series Maytag refrigerators (select models) Jenn-Air refrigerators (select models) Dacor refrigerators (select models) Thermador refrigerators (select models) Important — WISE System Compatibility: The 2188820 thermistor is compatible with non-WISE system refrigerators only. It is not compatible with newer Whirlpool refrigerators equipped with the WISE (Whirlpool Intelligent Smart Energy) control system. If your refrigerator uses the WISE system, this thermistor will not work correctly. Verify your model number before ordering, or contact our support team to confirm compatibility. Key Features NTC (negative temperature coefficient) thermistor — resistance decreases as temperature increases, allowing precise temperature monitoring 50K ohm resistance at 25°C (27K ohm at 0°C/32°F) — matches original WP2188820 specifications Wire length approximately 5.3 inches (13.46 cm) — standard length matching OEM dimensions Low-voltage design compatible with 5V/12V refrigerator control boards Continuously sends temperature readings to the control board to regulate compressor and fan operation Non-WISE system compatible only — verify your model before ordering Direct replacement for WP2188820, 2213442, AP6006068, and PS11739132 Compatible with Whirlpool, Kenmore, KitchenAid, Maytag, Jenn-Air, Dacor, and Thermador refrigerators Aftermarket replacement built to OEM-equivalent quality standards Quick DIY repair — installs in under 15 minutes Product Specifications Part Number 2188820 OEM Part Number WP2188820 Part Type Refrigerator Temperature Sensor (NTC Thermistor) Condition Aftermarket Replacement Sensor Type NTC (Negative Temperature Coefficient) Resistance at 25°C 50,000 ohms (50K ohm) Resistance at 0°C (32°F) 27,000 ohms (27K ohm) Wire Length Approximately 5.3 inches (13.46 cm) Voltage 5V / 12V (low voltage) WISE System Compatibility Non-WISE models only Compatible Brands Whirlpool, Kenmore, KitchenAid, Maytag, Jenn-Air, Dacor, Thermador Installation Notes ⚠️ Unplug Refrigerator Before Starting Disconnect power before beginning. The thermistor location varies by model — it is typically clipped to a bracket on the interior side wall of the fresh food or freezer compartment, or mounted near the evaporator coil. Consult your model's parts diagram or service manual to confirm the exact location before disassembly. Open the sensor cover or unclip the sensor bracket, disconnect the wiring connector, and pull the old thermistor out. Insert the new 2188820 thermistor, reconnect the wiring connector, and snap the cover or bracket back into place. Ensure the sensor head is positioned close to the compartment wall and the wiring is not pinched. Restore power and monitor the refrigerator temperature over the next few hours to confirm stable, accurate cooling. Tools needed: Phillips screwdriver (for panel access on some models); no tools needed for sensor replacement itself. Frequently Asked Questions What is the difference between 2188820 and WP2188820? These are the same thermistor. WP2188820 is the updated Whirlpool OEM part number that superseded the original 2188820. The 2213442 is also a cross-reference for the same part. This aftermarket replacement is compatible with all three numbers. What does an NTC thermistor do and how do I know if mine has failed? An NTC thermistor is a resistor whose resistance decreases as temperature increases. The control board sends a small voltage through the thermistor and measures the resulting resistance — a lower resistance means warmer temperature, and a higher resistance means cooler temperature. The board uses this reading to decide when to run the compressor and fans. A failed thermistor either reads open circuit (no continuity), short circuit (zero resistance), or provides incorrect readings that cause the refrigerator to run too warm, too cold, or cycle erratically. Test with a multimeter at room temperature — a working 2188820 should read approximately 50K ohms at 25°C (77°F). Significant deviation indicates failure. How do I know if my refrigerator uses the WISE system? The WISE (Whirlpool Intelligent Smart Energy) system was introduced on newer Whirlpool refrigerator models and uses a different thermistor specification that is not interchangeable with the 2188820. Models that use the WISE system are typically marked in the product documentation or on the control board. The easiest way to confirm compatibility is to verify your model number with our support team before ordering, or check whether WP2188820 appears in your model's official parts diagram. If your parts diagram lists WP2188820, this replacement is compatible. Where is the thermistor located in my refrigerator? The thermistor location varies by model and brand. On Whirlpool and KitchenAid models, it is commonly found on the interior side wall of the fresh food compartment clipped to a plastic housing. On some models it is located near the evaporator coil behind the freezer back panel. On Kenmore 106 series models, it may be on the fresh food section wall or inside the back panel. Consult your specific model's parts diagram or search for a model-specific installation video to locate the sensor before disassembling the refrigerator. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured with an NTC thermistor rated to the same 50K ohm specification as the original WP2188820 to match the performance and accuracy of the factory sensor. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

WR50X60 Refrigerator Genuine OEM Defrost Thermostat – For GE, Hotpoint, and Kenmore Product Overview The WR50X60 Refrigerator Defrost Thermostat is a genuine OEM part designed to regulate the defrost cycle by monitoring the temperature near the evaporator coils. When the temperature drops to a preset level, the thermostat activates the defrost heater to melt frost and maintain proper airflow. A faulty defrost thermostat can cause excessive frost buildup and cooling problems. This OEM replacement ensures reliable operation and is ideal for long-term use in compatible refrigerator models. Replaces Part Numbers This OEM thermostat replaces WR50X60, 3489, WR23X5030, WR50X0005, WR50X0007, WR50X0010, WR50X0011, WR50X0017, WR50X0021, WR50X0023, WR50X0026, WR50X0027, WR50X0036, WR50X0060, WR50X0076, WR50X0077, WR50X0089, WR50X0091, WR50X0093, WR50X0101, WR50X0105, WR50X0107, WR50X0110, WR50X0111, WR50X0115, WR50X0125, WR50X10, WR50X101, WR50X105, WR50X107, WR50X11, WR50X110, WR50X111, WR50X115, WR50X125, WR50X17, WR50X21, WR50X23, WR50X26, WR50X27, WR50X36, WR50X5, WR50X5009, WR50X5026, WR50X7, WR50X76, WR50X77, WR50X89, WR50X91, WR50X93, AH303547, EA303547, AP2071242, PS303547. It offers a direct fit and performance consistent with original factory-installed components. Compatible Brands Compatible with GE, Hotpoint, and Kenmore refrigerators made by GE. It fits various top-freezer, bottom-freezer, and side-by-side models that use this thermostat in their defrost systems. Fixes the Following Issues Frost accumulation in freezer Refrigerator not defrosting Blocked airflow due to ice Inconsistent cooling performance Why Buy from Parts‑O‑Matic 100% genuine OEM part for guaranteed compatibility Fast and free shipping throughout the U.S. Trusted by appliance technicians and DIYers Hassle-free returns and responsive support

Read more less

WB27X11213CM Microwave Fan Thermostat Closes at 158°F, Opens at 104°F. Fits GE Microwaves. Replaces Part Numbers:WB27X11213, WB24X28950, WB27X10846, SE-7350-004,  AP5791057, PS8754628.  This is an aftermarket part that can be used as a replacement for the OEM part. California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

ERWR50X122 Refrigerator Defrost Thermostat  L60-32F. 1/4" side push on clip. 11-3/4" leads with stripped wire ends. Replaces Part Numbers: WR50X122, 2387, AH303471, AP2071262, EA303471, PS303471, WR50X0122, WR50X0128, WR50X10014, WR50X128   This is an aftermarket part that can be used as a replacement for the OEM part.  California Residents Only - Warning: Cancer and Reproductive harm - https://www.p65warnings.ca.gov/

Read more less

XPARTCO W10316760 Refrigerator Thermistor Sensor – Compatible with Whirlpool, Kenmore, Maytag, and KitchenAid Refrigerators Product Description Maintain accurate refrigerator temperature control with the XPARTCO W10316760 Refrigerator Thermistor Sensor. This Refrigerator Thermistor Sensor is a replacement part for select Kenmore, KitchenAid, Maytag, Whirlpool refrigerator models. It is a crucial component responsible for accurately monitoring and regulating the temperature inside the refrigerator and freezer compartments. Replaces Part Numbers W10316760, WPW10323459, W10323459, 12791417, 12791417SP, 12791419SP, 1876627, W10280385, W10280386, W10308052, W10316760VP, W10438639, W10438761, W10452402, AH2580944, EA2580944, PD00006590, EAP2580944, AP4538142, PS2580944,  Compatibility This replacement thermistor sensor fits select Whirlpool, Kenmore, Maytag, Amana, Jenn-Air, and KitchenAid refrigerators. Example compatible models include (but are not limited to): Whirlpool WRS322FDAW04, Maytag MSS25N4MKZ00, and Kenmore 106.51133213. Always verify your refrigerator’s model number before ordering. Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement – Matches OEM temperature accuracy and response rate ❄️ Precision Cooling Control – Helps maintain stable refrigerator and freezer temperatures 💰 Affordable Alternative – Cost-effective solution versus expensive OEM sensors 🛠️ Simple Installation – Plug-in design for fast, hassle-free replacement 🛡️ Fixes Common Issues – Solves warm fridge, over-cooling, ice buildup, or erratic temperature cycling 📐 Product Specification Part Number: W10316760 Component Type: Refrigerator Thermistor / Temperature Sensor Material: Plastic probe housing with insulated wiring harness Resistance: ~2.7 kΩ at 77°F (varies with temperature) Mounting: Clips or adhesive tape depending on model location Compliance: Built to OEM-equivalent quality standards (not OEM) 🛠️ Installation Notes Tools Needed: Phillips screwdriver, needle-nose pliers (optional) ⚠️ Safety First: Always unplug the refrigerator before performing any repairs to prevent electrical shock. Steps: Disconnect power and remove interior shelves for access. Locate the existing thermistor near the evaporator or liner wall. Disconnect the wiring harness and remove any clips or tape. Install the new XPARTCO W10316760 thermistor in the same location. Reconnect the harness, secure wiring, and reassemble interior panels. Restore power and allow several hours for temperatures to stabilize. ⏱️ Time Required: 10–20 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Appliance Parts Supplier 🔄 30-Day Return Policy Restore accurate refrigerator cooling — Add to Cart Now for a reliable, budget-friendly repair!

Read more less